Polling the status of report_object_status

Instead of using a WHILE LOOP to get the get 'FINISHED' status of the report, any number of loops is suggested if we want to have a time out for this polling method?
Say
FOR i in 1..500? 1000? LOOP
END LOOP
anyone can give me a hint?
Thanks

You probably don't need this piece of code (the loop to check report status). It is usually used to wait for a report to finish, before calling the output with web.show_document.
If you run the report in SYNCHRONOUS mode, this loop is not necessary. See the online help:
Synchronous specifies that control returns to the calling application only after the called product has finished.

Similar Messages

I am trying to get waveform information out of my Tektronix TDS3034B scope. My implementation of serial polling of the status b yte register isn't working - any ideas???

My .VI is attached. Any, and all, suggestions would be greatly appreciated. My vi configures the oscilloscope, setting it for a single sequence (sample) waveform capture, then my attempt was to poll the status register until the 4th bit was set. The problem is that it never gets set. I know this because I put an indicator to light when it was true. Is there something that needs to be sent to the scope to cause it to enable the status register 4th bit when a waveform has been captured?
Attachments:
Configure 10u.vi ‏49 KB

Jryan,
Arrays in LabVIEW are "zero indexed" meaning that the first element in
an array has an index of zero. If you are sure your instrument
should be setting the 4th bit in the status register, then you will
want index 3. You could also use NI-Spy for a better look at what's happening on the GPIB bus.
Robert Mortensen
Software Engineer
National Instruments

Sender file adapter not polling the file

hi all,
i have configured a filexifile scenario....
but the file sender adapter is not polling the file at all....
i dont c any message either in RWB or in SXMB_MONI
i checked the adapter framework url at http://<ximachine>;<port>/AdapterFramework....and the status for the file adapter is green...
but the message it gives there is
Sender Adapter v1014 for Party '', Service 'TASL_FILE_SENDER':
Configured at 03:07:24 2006-02-02
Up and running - no message processing until now
last poll interval started 04:01:24 2006-02-02
length 60,000 secs
y is the sender adapter not polling the file..
i am using NFS as my File System....i gave the source directory as d:/test_dir/
is this way of specifying the source directory on a windows machine correct...
thanks
pavan

There is probably something wrong with the File Adapter. You will need to go to the RunTime Workbench >> Component Monitoring >> Display >> Click on the Adapter Engine >> More information will display and click on the button 'Adapter Monitoring' >> A new window will display and click on the arrow next to your adapter engine. This displays a list of adapters running on your system. Green light means good; Red, you have a configuration problem. Look at the error and try and resolve it.

Polling on status flag using Informatica

Hi Informatica guru's
how can Informatica workflow do polling (10 attempts MAX) on the status flag of a particular table at a fixed time interval of every 5 minutes.
On the 10th Attempt ,if the status is still not yet changed ,then the Informatica workflow to be marked as failed.
later an email to be sent about the workflow failure.
how do I develop the above logic?
please help me ASAP.
Thanks & warm regards,
Kam

did you ever figure out how to do this? I need to do the same thing.
Thanks,
Angie

Sun Netra T5220 will not poweron (FATAL: Polling POK Status Time Out)

Hey All,
New to the forums here.
We have a SUN Netra T5220 which we are unable to poweron, failing with a couple FATAL errors.
sc> showlogs
Log entries since Apr 20 07:48:41
Apr 20 07:48:41: Chassis |critical: "CRITICAL ALARM is set"
Apr 20 07:48:41: Chassis |critical: "CRITICAL ALARM is set"
Apr 20 07:48:41: Chassis |critical: "Host has been powered off"
Apr 20 07:52:23: Audit |minor : "root : Set : object = /SYS/power_state : value = on : success"
Apr 20 07:52:33: Chassis |critical: "Apr 20 07:52:33 *FATAL: Polling POK Status Time Out: 0x9f*"
Apr 20 07:52:33: Chassis |critical: "Apr 20 07:52:33 *FATAL: The HOST Processor has a configuration error, forcing a power-down*"
Apr 20 07:52:33: Chassis |critical: "CRITICAL ALARM is set"
Apr 20 07:52:33: Chassis |critical: "Host has been powered off"
Apr 20 08:04:32: Audit |minor : "root : Set : object = /SYS/power_state : value = on : success"
Apr 20 08:04:42: Chassis |critical: "Apr 20 08:04:42 FATAL: Polling POK Status Time Out: 0x9f"
Apr 20 08:04:42: Chassis |critical: "Apr 20 08:04:42 FATAL: The HOST Processor has a configuration error, forcing a power-down"
Apr 20 08:04:42: Chassis |critical: "CRITICAL ALARM is set"
Apr 20 08:04:43: Chassis |critical: "Host has been powered off"
Apr 20 08:07:54: Audit |minor : "root : Close Session : object = /session/type : value = console : success"
Apr 20 08:08:10: Audit |minor : "admin : Open Session : object = /session/type : value = console : success"
Apr 20 08:12:59: Audit |minor : "admin : Set : object = /SYS/power_state : value = on : success"
Apr 20 08:13:09: Chassis |critical: "Apr 20 08:13:09 FATAL: Polling POK Status Time Out: 0x9f"
Apr 20 08:13:09: Chassis |critical: "Apr 20 08:13:09 FATAL: The HOST Processor has a configuration error, forcing a power-down"
Apr 20 08:13:10: Chassis |critical: "CRITICAL ALARM is set"
Apr 20 08:13:10: Chassis |critical: "Host has been powered off"
sc> showfaults
Last POST Run: Sat Mar 26 06:38:35 2011
Post Status: Passed all devices
No failures found in System
curious if any of you all have seen this type of error before and what may be the resolution.
Thanks in advance for any responses,
rbrociek

rbrociek,
It looks like the system board or power distribution board is faulty.
You should open a SR in My Oracle Support.
Regards.

The status bar is pushed up at about 3/4 of the screen, so I can view onlu firefox at about 1/4, good thing there is a scroll bar, but below the status bar is white display? can u please help me, I want to drag down the status bar so I can have a full vi

The status bar is pushed up at about 3/4 of the screen, so I can view only Firefox at about 1/4, good thing there is a scroll bar, but below the status bar is white display? can u please help me, I want to drag down the status bar so I can have a full view
== This happened ==
Every time Firefox opened

Your code is absolutely unreadable - even if someone was willing to
help, it's simply impossible. I do give you a few tips, though: If you
understand your code (i.e. if it really is YOUR code), you should be
able to realize that your minimum and maximum never get set (thus they
are both 0) and your exam 3 is set with the wrong value. SEE where
those should get set and figure out why they're not. Chances are you
are doing something to them that makes one 'if' fail or you just
erroneously assign a wrong variable!

FM to read the different steps in workflow and the status at each step

Hi All,
Is there any FM in SAP which gives the detail roadmap of the steps taken in a workflow and the diffrent status or decision at each step.
I am looking for something like what you see when you click on the "STARTED WORKFLOW" in the business workplace outbox.
Which shows up the "steps in the process so far " and the decision and the agents for each of them.
Thanks,
Charan.

Hi,
You can get the status according to the task. please check with FM "SAP_WAPI_GET_WI_DELTA".
Regards
SM Nizamudeen

Error while checking the status of Oracle Cluster ware

Hi
I was trying to install the database using dbca after setting up the grid and database software on LINUX x86-64 RHEL 5.7 machine. The database software version is 11.2.0.3. It throwing the error regarding the connectivity of clusterware. So I checked the status of clusterware.
-bash-3.2$ ./crsctl stat res -t
CRS-4535: Cannot communicate with Cluster Ready Services
CRS-4000: Command Status failed, or completed with errors.
-bash-3.2$
But when I ran below one:
-bash-3.2$ ./crsctl stat res -t -init
NAME TARGET STATE SERVER STATE_DETAILS
Cluster Resources
ora.asm
1 ONLINE ONLINE sfv9699 Started
ora.cluster_interconnect.haip
1 ONLINE ONLINE sfv9699
ora.crf
1 ONLINE ONLINE sfv9699
ora.crsd
1 ONLINE OFFLINE
ora.cssd
1 ONLINE ONLINE sfv9699
ora.cssdmonitor
1 ONLINE ONLINE sfv9699
ora.ctssd
1 ONLINE ONLINE sfv9699 OBSERVER
ora.diskmon
1 OFFLINE OFFLINE
ora.drivers.acfs
1 ONLINE ONLINE sfv9699
ora.evmd
1 ONLINE INTERMEDIATE sfv9699
ora.gipcd
1 ONLINE ONLINE sfv9699
ora.gpnpd
1 ONLINE ONLINE sfv9699
ora.mdnsd
1 ONLINE ONLINE sfv9699
So i saw that the crsd having some issue. I checked the alert log and crsd log. Below are the output.
Alert <server_name>.log
2012-10-20 15:37:51.408
[ohasd(3694)]CRS-2765:Resource 'ora.crsd' has failed on server 'sfv9699'.
2012-10-20 15:37:52.968
[crsd(5188)]CRS-1013:The OCR location in an ASM disk group is inaccessible. Details in /oracle2/app/11.2.0/grid/log/sfv9699/crsd/crsd.log.
2012-10-20 15:37:52.984
[crsd(5188)]CRS-0804:Cluster Ready Service aborted due to Oracle Cluster Registry error [PROC-26: Error while accessing the physical storage
ORA-27140: attach to post/wait facility failed
ORA-27300: OS system dependent operation:invalid_egid failed with status: 1
ORA-27301: OS failure message: Operation not permitted
ORA-27302: failure occurred at: skgpwinit6
ORA-27303: additional information: startup egid = 1000 (oinstall), current egid = 10002 (dba)
]. Details at (:CRSD00111:) in /oracle2/app/11.2.0/grid/log/sfv9699/crsd/crsd.log.
2012-10-20 15:37:53.471
[ohasd(3694)]CRS-2765:Resource 'ora.crsd' has failed on server 'sfv9699'.
2012-10-20 15:37:53.472
[ohasd(3694)]CRS-2771:Maximum restart attempts reached for resource 'ora.crsd'; will not restart.
CRSD.log
2012-10-20 15:37:52.456: [ CRSMAIN][3563381328] Checking the OCR device
2012-10-20 15:37:52.457: [ CRSMAIN][3563381328] Sync-up with OCR
2012-10-20 15:37:52.457: [ CRSMAIN][3563381328] Connecting to the CSS Daemon
2012-10-20 15:37:52.457: [ CRSMAIN][3563381328] Getting local node number
2012-10-20 15:37:52.459: [ CRSMAIN][3563381328] Initializing OCR
[ CLWAL][3563381328]clsw_Initialize: OLR initlevel [70000]
2012-10-20 15:37:52.897: [ OCRASM][3563381328]proprasmo: Error in open/create file in dg [DATA]
[ OCRASM][3563381328]SLOS : SLOS: cat=7, opn=kgfoAl06, dep=27140, loc=kgfokge
2012-10-20 15:37:52.898: [ OCRASM][3563381328]ASM Error Stack : ORA-27140: attach to post/wait facility failed
ORA-27300: OS system dependent operation:invalid_egid failed with status: 1
ORA-27301: OS failure message: Operation not permitted
ORA-27302: failure occurred at: skgpwinit6
ORA-27303: additional information: startup egid = 1000 (oinstall), current egid = 10002 (dba)
2012-10-20 15:37:52.967: [ OCRASM][3563381328]proprasmo: kgfoCheckMount returned [7]
2012-10-20 15:37:52.967: [ OCRASM][3563381328]proprasmo: The ASM instance is down
2012-10-20 15:37:52.968: [ OCRRAW][3563381328]proprioo: Failed to open [+DATA]. Returned proprasmo() with [26]. Marking location as UNAVAILABLE.
2012-10-20 15:37:52.968: [ OCRRAW][3563381328]proprioo: No OCR/OLR devices are usable
2012-10-20 15:37:52.968: [ OCRASM][3563381328]proprasmcl: asmhandle is NULL
2012-10-20 15:37:52.969: [ GIPC][3563381328] gipcCheckInitialization: possible incompatible non-threaded init from [prom.c : 690], original from [clsss.c : 5326]
2012-10-20 15:37:52.975: [ default][3563381328]clsvactversion:4: Retrieving Active Version from local storage.
2012-10-20 15:37:52.978: [ CSSCLNT][3563381328]clssgsgrppubdata: group (ocr_SFV9699-cluster) not found
2012-10-20 15:37:52.978: [ OCRRAW][3563381328]proprio_repairconf: Failed to retrieve the group public data. CSS ret code [20]
2012-10-20 15:37:52.981: [ OCRRAW][3563381328]proprioo: Failed to auto repair the OCR configuration.
2012-10-20 15:37:52.981: [ OCRRAW][3563381328]proprinit: Could not open raw device
2012-10-20 15:37:52.981: [ OCRASM][3563381328]proprasmcl: asmhandle is NULL
2012-10-20 15:37:52.983: [ OCRAPI][3563381328]a_init:16!: Backend init unsuccessful : [26]
2012-10-20 15:37:52.984: [ CRSOCR][3563381328] OCR context init failure. Error: PROC-26: Error while accessing the physical storage
ORA-27140: attach to post/wait facility failed
ORA-27300: OS system dependent operation:invalid_egid failed with status: 1
ORA-27301: OS failure message: Operation not permitted
ORA-27302: failure occurred at: skgpwinit6
ORA-27303: additional information: startup egid = 1000 (oinstall), current egid = 10002 (dba)
2012-10-20 15:37:52.984: [ CRSMAIN][3563381328] Created alert : (:CRSD00111:) : Could not init OCR, error: PROC-26: Error while accessing the physical storage
ORA-27140: attach to post/wait facility failed
ORA-27300: OS system dependent operation:invalid_egid failed with status: 1
ORA-27301: OS failure message: Operation not permitted
ORA-27302: failure occurred at: skgpwinit6
ORA-27303: additional information: startup egid = 1000 (oinstall), current egid = 10002 (dba)
2012-10-20 15:37:52.984: [ CRSD][3563381328][PANIC] CRSD exiting: Could not init OCR, code: 26
2012-10-20 15:37:52.984: [ CRSD][3563381328] Done.
=======================
I see in the above log that saying ASM instance is down and failed to open +DATA .
But the asm instance up and running
SQL> select instance_name,status from v$instance;
INSTANCE_NAME STATUS
+ASM1 STARTED
And we havent created any disk named DATA before the installation. We have created only below two disks
SQL> select name,header_status from v$asm_disk;
NAME HEADER_STATUS
ASM_DATA MEMBER
FLASH_RECOVERY MEMBER
But I am seeing a diskgroup in the v$asm_diskgroup which we havent created.
SQL> select name,state from v$asm_diskgroup;
NAME STATE
DATA MOUNTED
Ya this is a second time installtion. In the first installtion we created the asmdisk as DATA. But later everything (RAW device ) was formatted and this new disks has been created and installtion again started
[root@SFV9699 bin]# oracleasm listdisks
ASM_DATA
FLASH_RECOVERY
Seems like its trying to read the old disk DATA.
we have done asmscanning too with oracleasm scan disks. but no use.
Where I can remove the old entry of DATA disk.
It would be a great if a quick response get.
Thanks
SHIYAS M

The permission looks fine. If it was permission issue then y it is trying to read the DATA disk which I havent created this time at all ( But created in the first installation).
2012-10-20 15:37:52.459: [ CRSMAIN][3563381328] Initializing OCR
[ CLWAL][3563381328]clsw_Initialize: OLR initlevel [70000]
2012-10-20 15:37:52.897: [ OCRASM][3563381328]proprasmo: *Error in open/create file in dg [DATA]*[ OCRASM][3563381328]SLOS : SLOS: cat=7, opn=kgfoAl06, dep=27140, loc=kgfokge
2012-10-20 15:37:52.898: [ OCRASM][3563381328]ASM Error Stack : ORA-27140: attach to post/wait facility failed
ORA-27300: OS system dependent operation:invalid_egid failed with status: 1
ORA-27301: OS failure message: Operation not permitted
ORA-27302: failure occurred at: skgpwinit6
ORA-27303: additional information: startup egid = 1000 (oinstall), current egid = 10002 (dba)
2012-10-20 15:37:52.967: [ OCRASM][3563381328]proprasmo: kgfoCheckMount returned [7]
2012-10-20 15:37:52.967: [ OCRASM][3563381328]proprasmo: The ASM instance is down
2012-10-20 15:37:52.968: [ OCRRAW][3563381328]proprioo: *Failed to open [+DATA].* Returned proprasmo() with [26]. Marking location as UNAVAILABLE.
2012-10-20 15:37:52.968: [ OCRRAW][3563381328]proprioo: No OCR/OLR devices are usable
2012-10-20 15:37:52.968: [ OCRASM][3563381328]proprasmcl: asmhandle is NULL
The only disks created are
[root@SFV9699 dev]# oracleasm listdisks
ASM_DATA
FLASH_RECOVERY
And these disks are showing part of that group also.. Not quite sure how this happened..
what abt dropping this group.. will anything work.

Error while updating the status record of IDOC in SAP

Hi All,
I am facing this problem. I have done outbound processing and IDOC was sent successfully from SAP to EDI system and it was processed in EDI and now EDI system wants to send the status back to SAP with a status message and the status number that we are using is '24' and we have mapped all the fields in the status table EDIDS and made sure that EDI system sends all those and I think Counter field can not be determined by EDI system so EDI system used the counter '1' since it can not determine how many counters are already there in SAP and unless we pass the value to this counter field we were getting the error. After passing all the values the status of the IDOC is updated with the status '00' instead of '24' and we do not know why it is happened and I would like to know how SAP converts the status record that is received from the EDI system.
Please let me know how the status record will be translated into SAP from EDI system and I ahve followed basically EDIDS structure and the IDOC status is updating in SAP but with wrong status number and the alignemnt also missing in SAP fields like if I give some text in the EDI it is splitting and storing in 2 fields.
Please help me in this and I think I have explained the problem in a detail manner.
Thanks,
Ramesh.

Hi Naresh,
Thanks for the reply and my question is since EDI system is able to send the status back to SAP from EDI system and only problem is it is updatinf the status wrong and I have checked the EDIDS table also and the entry is creating with another counter and please confirm me that it is because of EDI does not support the status record update so that I can confirm to the client that there is nothing wrong in the way SAP functions and EDI system can not update the status code in the SAP.
Thanks,
Ramesh.

Changing Portal Role after the status change of user status at the CRM end.

Hi,
I have Portal with Java database as the default and CRM is connected to it using SSO.The database in both the case in separate.The users that are created in Portal will have a BP status in CRM sytsem.
Now my requirement is that if the status of the BP gets changed at the backend simultaneoulsy its Portal role should also gets changed.How shall i facilitate this procedure of changing the Portal Role?
Is there any RFC ,BAPi or Webservices required for this?
Regards,
Amarys
Edited by: amarys on Sep 13, 2011 11:20 AM

Hello,
Since the status has no number it will appear under statuses W/O number bottom right in status overview window.
These status will appear as additional text beside current user status. For example if user staus is BUG and status without number is DFL and sets when deletion flag is set and gets deleted when it is revoked than user status will appear as
BUG DFL -
Deletion flag set.
BUG -
When deletion flag revoked.
You have to live with it. I don't think there is a way out for that.
Thanks
Saikishore Ganga.

Problems with Syncing iPhone 3G (4.2.1. iOS). What is appearing in the status bar is "Syncing "untiled playlist.." and its stuck at backing up. I noticed that my name has been replaced to "untitled playlist". Whats wrong

Problems with Syncing iPhone 3G (4.2.1. iOS). What is appearing in the status bar is "Syncing "untiled playlist.." and its stuck at backing up. I noticed that my name has been replaced to "untitled playlist". Whats wrong

Welcome to Apple Discussions!
Maybe a long shot, but WD is not known for the quality of some of their enclosures, although I do like the drives themselves. It may be worth mounting this drive in a different enclosure, something like one of OWC's FireWire enclosures with the highly reliable Oxford chip sets. I wouldn't be inclined to trust a WD enclosure, especially if it already seemed to be acting in a flakey manner.
Here's an example of what I mean:
http://eshop.macsales.com/item/Other%20World%20Computing/MEP924FW8E2O/
I have 3 of these and I really like them.
From what I understand, if the drive spins up, it is often possible to recover data from it. To be absolutely certain to destroy the data, you just about have to take a hammer to the disk. Hopefully, there will be a way to get your data back.
Good luck!

How do you use the status column to show progress of a step in an OI?

Hi everyone,
I was just doing a little browsing and noticed the picture at the top of the http://www.ni.com/teststand/ web page. It shows a progress bar in the status column of a step being executed.
I have several applications where this would be a very useful addition. I use the progress bar at the bottom of the OI and sequence editor regularly, but would very much like to show progress of an individual step in the status column. It would be particularly useful where you turn the tracing off into a sequence but want to see that progress is being made through the steps within it...
Anyone know how to do this? I have been unsuccessful in trying to find examples....
Cheers,
Barry

James,
I believe your answer to Bazza's question also applies to my situation, but I wasn't sure so I thought I would ask. I am working on a custom TestStand operator interface in LabVIEW using the UI controls. I would like it to behave as closely as possible to the old Test Executive. Specifically, I would like the operator to be able to see the contents of the sequence file, interact with them, and see the execution results all in the same view. Is that possible? In other words, can I display and interact with a sequence file (display the sequence steps, run selected steps, loop selected steps, etc.) and display the sequence's execution results (including tracing) in the same SequenceView control or do I have to use 2 of them?
Thanks,
Ryan Wright

Is there a BAPI that gives the status information (and possibly more) of a

Hi All,
We are using an external document image system where we scan and code vendor invoices. They are send to our SAP system via a BAPI.
We want to update the status of the invoice in the document image system from the status in the SAP system, so whether it is still open or has been paid and cleared. Is there a BAPI that gives the status information (and possibly more) of a specific vendor open item?
Regards,
Gerrit

Are you sure about that? Several highly regarded, widely downloaded apps, e.g., eReader, have an option to hide the status bar. The developer forums are awash in discussions about the commands to hide the status bar-- it's built in to the SDK.
I figure someone will have put out a small program that does nothing but hide the status bar or allow its tweaking... much like StatusBar does on the Palm OS 5 PDAs...

How do I enable some scripts to run in some programs/websites and what happened to the status bar of my Mozilla Firefox 4?

Well, first of all, I was tying to create a web-based computer game in Notepad in H.T.M.L., C++, and JavaScript codes. But when I tried to open the completed product, Firefox only came up with a blank page. What do I do with this? And also, I unwittingly removed the "Status Bar" on the bottom side of my browser(the one that always says "Transferring data from/to..."), and when I tried to bring it back up, I couldn't because I don't know how, since I'm new to Mozilla Firefox 4. If you could help me with these problems, Then I would greatly appreciate it.

You can install the Status-4-Evar extension to regain some functionality from previous Firefox versions that was lost with the removal of the Status bar.
Open the Customize window via "View > Toolbars > Customize" or via "Firefox > Options > Toolbar Layout" after you have installed the Status-4-Evar extension and drag the items (Status Text, Progress Meter, Download Status) upon the Add-ons Bar (View > Toolbars > [X] Add-on Bar) 
Also check the Options of Status-4-Evar in Firefox (or Tools) > Add-ons
* Status-4-Evar: https://addons.mozilla.org/firefox/addon/235283/

The status of scheduled report in java application ?

Post Author: Jay_Misys
CA Forum: JAVA
My java application is running on application server (websphare / java application server)
I schduled the report published on crystal report server
the java code is like:
BIPlatform bipService = new BIPlatform(new Connection(new URL(servicesURL + "/biplatform")), oSession.getConnectionState());
ResponseHolder rh=bipService.get("path://InfoObjects/"+sCrystal_Reports_Folder + reportName +
"@SI_SCHEDULEINFO,SI_PROCESSINFO" ,oGetOptions);
InfoObjects oInfoObjects = rh.getInfoObjects();
CrystalReport oCrystalReport = (CrystalReport)oInfoObjects.getInfoObject(0);
SchedulingInfo schedulingInfo = oCrystalReport.getSchedulingInfo();
schedulingInfo.setRightNow(Boolean.TRUE);
oCrystalReport.setPluginProcessingInterface(procInfo);
oInfoObjects.setInfoObject(0,oCrystalReport);
bipService.schedule(oInfoObjects);
Pls help me to get the status (running / sucessfully generated/ failed etc...) of scheduled report ?

out = new FileOutputStream(matcher.group(1)+".open" , true);
                      FileChannel ch = out.getChannel();
                                   FileLock lock = ch.lock(0L, Long.MAX_VALUE, false);
                               // Connect print stream to the output stream
                                   p = new PrintStream( out );
                        p.println ("\n" + parms.getProperty( value ) + "\n");
                              p.flush();
                        p.close();
                              lock.release();Ok, I tried implementing locks but I dont know why it is not working...An exception is thrown and nothing is wriiten to the file. I have employed a complete lock on the file so that no other JVM application can use it.
Actually this is a server that grabs data sent from an Iframe and writes it down to a temp file. I open a file input stream, lock it and then use a printwriter strream to write the realyed data to the file. Any inputs as to what is wrong with the code snippet above?????

Polling the status of report_object_status

Similar Messages

Maybe you are looking for