Power over ethernet for AIR-BR1310G

Hello
i have AIR-BR1310G that came with its proper power injector AIR-PWRINJ-BLR2 can this power injector be feed using a POE switch or do i have to use the 48v power adapter
regards
Elie

ELie: no PoE. You can only use power supply to operate the bridge.
HTH
Amjad
Sent from Cisco Technical Support iPad App

Similar Messages

  • 1300 Series Access Point/Bridge Power Injector - Using power over ethernet

    Can I use power over ethernet to supply the Injector with power?

    Hi Mikael,
    Sorry, this will not work. Have a look at these specs;
    1300 Series Power
    Power
    The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.
    The power injector is available in two models:
    Cisco Aironet Power Injector LR2 standard version (included with the access point/bridge)
    48-VDC input power
    Uses the 48-VDC power module (included with the access point/bridge)
    Cisco Aironet Power Injector LR2T optional transportation version
    12- to 40-VDC input power
    Note The power injector and the power module must not be placed in an outdoor unprotected environment. The power module must not be placed in a building's environmental air space, such as above a suspended ceiling.
    http://www.cisco.com/en/US/products/ps5861/products_installation_guide_chapter09186a008079b93b.html#wp1051840
    Dual coaxial cable to run from the power injector to the 1300. See attached notes:
    Cisco Aironet 1300 Series
    Cisco Aironet 1300 Series Access Point/Bridge Power Injector
    The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html
    Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide
    Ethernet Ports
    The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_installation_guide_book09186a00804d3095.html
    AIR-PWRINJ-BLR2
    F-Type Connectors
    Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html
    Hope this helps!
    Rob

  • Power Over ethernet on Cisco switches - why??

    I administer 3 servers (two g4 towers and one xserve attached to an XCraid) and 50 Macintosh workstations in an agency/production group within a fairly large company (2000+). Like most major companies the majority of the computer and servers are Windows based (specifically DELL) with CISCO switches.
    I ran into a problem today where a switch was updated the "OS of the swithc" without my knowledge by our Infrastructure group. This resulted in a very high latency problem when pulling files from our Apple servers. After some digging we determined that the feature "Power Over Ethernet" had been disabled when they updated the switch's OS. Once we enabled PoE back on those ports, it was back to business.
    My question here is, why does this feature have to be enabled? All DELL servers reconnected without a hitch. I hear PoE is only really resevered for VoiP devices and such. What is it with Apple servers that need this feature turned on?
    Look forward to hear from you all.
    Xserver, Xraid, G5, etc   Mac OS X (10.4.6)  

    I can confirm that portfast makes a huge difference, as the autonegotiation between the switch and the client is performed inside of about 2 seconds, rather than the standard thrash-around period of about 40 seconds that some ethernet devices can use to determine line speed and simplex / duplex operation.
    Turn on portfast on any switch ports that you don't plan on using for trunking / uplinking. When you do this, it tells the switch that there isn't a managed switch / router downstream, so it doesn't need to try to negotiate routing protocols and whatnot - it greatly speeds up the autonegotiation process.
    Also, on some Cisco switches (We found it on a Cisco Catalyst 4006) if you lock the port to a specific operating speed / mode (e.g. 100Mbps / full duplex), the Mac doesn't like it nearly as much as if you leave it to autonegotiation. We were having the exact same issue the OP is seeing (limited bandwidth, massive CRC error count) until we put it back to auto and enabled portfast, and then we got the performance we expected, without recurrence of the issue.

  • How do I set up multiple Airport Expresses to connect over ethernet for Airtunes only?

    I am trying to set up an Airtunes network using an Airport Extreme and three Airport Expresses connected together via ethernet (CAT5 cable). At each Airport Express there will be a speaker setup. I don't need/want internet connectivity on the network, but not sure if it is required for setup or not. I have made this work over wifi, using the Expresses to extend the network, but struggling to get this to work over ethernet.
    I would be verry grateful of a step-by-step method to setting this up! I am also looking to set up 6 airport expresses to do the same thing in another location.
    Thanks in advance!

    Thanks for the info.
    I assume that the AirPort Extreme is setup and working at this point.
    Work with one AirPort Express at a time to get them all configured, and then you can locate them where they will be needed.
    AirPort Setup will configure the Express devices to "extend a wireless network" using Ethernet, so they will be broadcasting the same wireless signal as the AirPort Extreme and provide more wireless signal coverage as well.
    I have yet to meet the first person who thought that they had too much wireless coverage, but you would have the option to turn off the wireless on the Express if you wanted. Most users like having extended wireless for their devices.
    Temporarily, move an Express close to the AirPort Extreme
    Connect a spare Ethernet cable from one of the LAN <-> ports on the Extreme to the WAN "O" port on the Express
    Power up the Express for a few minutes
    Hold in the reset button on the back of the Express for 10 seconds and release. Allow a full minute for the Express to restart to a slow, blinking amber light.
    Click the Airport icon at the top of the Mac's screen and wait a few seconds for AirPort Express to appear just under the listing of New AirPort Base Station
    Click directly on the AirPort Express
    AirPort Setup will open up automatically and take a minute to analyze the network, then announce that the Express will be configured to extend the AirPort Extreme network.
    Enter a device name that you want to use....example.....Express1.....and click Next
    AirPort Setup will configure everything for you. Notice that the message will say that the Express is being set up to extend using Ethernet. When you see the message of setup complete, click Done.
    Now you can move the Express to the remote location where it is needed, hook it up to the Ethernet connection there, power up the Express and set up AirTunes on the device.
    AirTunes is enabled by default, to other than make the speaker connection, you won't have much to do on that.
    Set up other Express devices the same way, except assign a different name to each device....example....Express2, Express3, etc.....to keep things organized.

  • Aironet 1100 / 802.3af Power Over Ethernet (POE) Support

    I was under the impression that the Aironet 1100 supports 802.3af POE. I purchased a NetGear FS108P POE switch, however, when I plug in the 1100, it does not receive any power.
    I have seen references in the documentation to a Cisco inline power injector and a Cisco Catalyst switch that can provide POE to the 1100 and maybe they will work, however, will the 1100 only work with those devices?? If so, it would seem that the 1100 really doesn't support the 802.3af standard and that Cisco's implementation of POE is proprietary.
    Any input would be appreciated.
    Thanks,
    Michael

    Hi Michael,
    As you have discovered (unfortunately) is that the 1100 only supports Cisco Pre-standard PoE :( Have a look;
    Single 802.11g radio offering 54 Mbps of capacity
    2.4 GHz integrated diversity dipole antennas
    Available in an autonomous version only
    16 MB of memory with 8 MB of storage
    Operating temperature range of 32 to 104?F (0 to 40?C)
    **Inline power support (Cisco pre-standard)**
    From this doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps4570/prod_brochure0900aecd8035a015.html
    The good news is that either of the options you listed will work just fine. I would go for the power injector probably just for neatness sake.
    POWERING OPTIONS
    The Cisco Aironet 1100 Series can be powered either locally using the AC-DC power adapter, or over the Ethernet cable when coupled with a device capable of delivering in-line power, such as an in-line power-capable Cisco Catalyst? switch, Catalyst in-line power patch panel, or Cisco Aironet Power Injector.
    The AC-DC power adapter is included with the access point and can also be ordered as a spare part. The Cisco Aironet Power Injector can either be configured to the order or can be ordered separately.
    You can use either;
    AIR-PWR-A= Cisco Aironet Power Supply-Input 110-240VAC, Output 48VDC, 380 mA-for 1100 and 1200 Series
    AIR-PWRINJ3= Cisco Aironet Power Injector for the 1100 and 1200 Series Access Points
    From this doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_data_sheet0900aecd8045690f.html
    Hope this helps! And good luck!
    Rob
    Please remember to rate helpful posts.....

  • Gigabit Ethernet for Air...

    I purchased the 10/100 mbps Apple ethernet adapter with my new air... It took overnight to restore my backup from my Time Capsule (much slower than my previous Macbook Pro).
    I know that USB is theoretically limited to 480 mbps.
    I know that the Apple adapter is limited to 100 mbps.
    USB can handle more than 100 mbps even if isn't going to reach theoretical limit of 480 mbps - Especially when I'm not doing anything but backing up/restoring.
    If you go to Amazon - there are a few Gigabit adapters that have reviews from Air owners that have experienced transfer throughput that's a lot higher than 100 mbps...
    I'd like an alternative to the Apple solution, but before I purchase something - I want to hear from people who have first hand experience with an adapter as a recommendation. Some of these adapters required beta drivers which I do not want to meddle.
    thanks

    Thanks for the advice but that's a bit much for an ethernet adapter
    I tried to find more information about the Presto unit but their website is horrible - No information about their own product aside from a press release and a pretty picture.
    I guess no one has tried this little comparison so what the ****, I might as well and post my results. I went to Micro Center and purchased a Belkin Gigabit USB 2.0 Network Adapter.
    Here are my results.
    802.11 N Wireless to my Time Capsule (1st gen)
    Write: 7.3 Mbps (58.4 mbps)
    Read: 7.6 Mbps (60.8 mbps)
    Apple USB "Fast" Ethernet adapter to Time Capsule (1st gen)
    Write: 11.1 Mbps (88.8 mbps)
    Read: 8.2 Mbps (65.6 mbps)
    Belkin "Gigabit" USB 2.0 Network Adapter to Time Capsule (1st gen)
    Write: 20 Mbps (160 mbps)
    Read: 28 Mbps (224 mbps)
    So there you have it - I don't expect to get Gigabit speed 125 Mbps (1000 mbps), but getting nearly twice the write speed makes backing up and restoring a lot faster. Interesting to note - I have read posts that state there will be issues with Gigabit (1000 mbps) over USB 2.0 (480 mbps) - I noticed none...
    The Belkin adapter is not as pretty as the Apple adapter - The blue LEDs can be used as a flash light they are so bright, but it does a better job.

  • Time Capsule Backup over ethernet for PC

    Hi,
    I am planning to buy a Time Capsule.
    I have a macbook and a PC with Windows Vista.
    My PC does not have the Wireless option, so i have to connect it to the Time capsule through ethernet to use it as a router.
    I have 300 GB of files on my PC, how do i transfer this to the time capsule hard drive.........on the website it says Time capsule is a "wireless shared hard drive".....what does this mean......does it mean i cannot transfer my 300GB files from my PC to the Time capsule hard drive through the ethernet cable.

    You can use Ethernet to transfer files and acess the Internet through the time capsule.

  • Power supply requirement for SM-ES3G-16-P

    I need 3925 router and i want to install SM-ES3G-16-P etherswitch module with PoE into it. So my question is do I need PoE power supply or not? Will PoE ports on this module work with basic AC power supply?

    Thank you for your reply. I've read the document, but it is still not clear to me though.
    Document says: "Power over Ethernet requires the PoE versions of the router power supplies". I have two PWR-3900-AC power supplies in the 3925 router (not PoE versions). So I will have no PoE on the etherswitch ports? (despite the fact that there is enough power on this two power supplies to set PoE up)

  • Ignore Ethernet for Internet.

    I am trying to network a Mac Mini OSX.6.4 and a MacBook Pro OSX.6.4 over ethernet for screen sharing/file-transfer. And using a separate WiFi network for internet access. I have internet working and the Mini shows up as an available comp in Finder, but it won't make the connection.

    Thats what I thought but I just couldn't find conformation.
    Thanks

  • I synced about 50 books to my new ipad air 2.  When I click any other books, the sync starts all over again for all books (it shows 51 books syncing).  If I abort the sync, all of a sudden, all books are gone from my ipad.  I don't know why.

    I synced about 50 books to my new ipad air 2.  When I click any other books, the sync starts all over again for all books (it shows 51 books syncing).  If I abort the sync, all of a sudden, all books are gone from my ipad.  I don't know why.  I did not have this problem on my old ipad...or before I upgraded to the latest version of iTunes.  Any help would be greatly appreciated.

    Hi were you able to resolve yours?
    I was very worried losing all my medical stuff on my iPad Air 2, plus i have nothing to use for the next day! So i have to try all the possible things i read on the internet!! And this worked on my part (Thank God, and thank you Google)
    Perform a hard reboot
    Hold down the Home button and Power button on your iPhone or iPad and keep holding them until you see the Apple logo. Once you do, you can let go. When your device boots back up, go ahead and check to see if the apps have started re-downloading. If they still appear to be stuck, continue on.

  • When I power up my ipad air the apple logo comes up like it should then the lock screen only comes up for a second or less so I can't swipe it fast enough.

    When I power up my iPad Air the Apple Logo comes up like it should then the lock screen only comes up for a second or less so I can't swipe it fast enough to get to the home page. The lock screen just disappears. I have to hit the sleep/wake or home button to bring the lock screen back up so I can swipe it. Have others found this situation with the iPad Air. I have an iPad 2 and it does not happen at all. The Apple store checked it out. One rep said to me this is unusual and had a tech check it out and they said this is normal. If the iPad is suppose to be user friendly, why this extra step to get to the lock screen? Are other owners of the iPad Air having the same problem? If so, what have you done to correct it?

    Try this  - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.) No data/files will be erased.
     Cheers, Tom

  • Choosing the Right Network Protocol for CRIO 9024 to PXI over Ethernet

    We are in the design phase of setting up a CRIO 9024 Embedded Controller to send data captured to a PXIe-8105 Controller over ethernet. The data will be be 2D arrays of double precision. This data will need to be sent to the pxi at the end of each test step. Each step will have different number of channels and sample rates.
    For example,  Test Step 1 will have 5 channels of Analog inputs that will be sampled at 100,000 KHz for 1 second. This data will be coming from the CRIO FPGA. The data will get post processed by the CRIO 9024 and analyzed for pass or fail metrics. Then, the CRIO controller will send the 2D Array of Data (500,000 data points 5 X 100,000) and the results of all the metrics (a 1D array) to the PXI.
    The connection to the PXI will be using Ethernet.
    Keep in mind that the PXI will also have to send the CRIO some values to tell the CRIO when to start the test and when the test sequence is complete.
    I was thinking TCP/IP would work best because of the 2 way communication needed. But then I was looking at Network Streaming or even using Shared Variables.
    If anyone has any ideas or suggestions please please post them.
    Spark
    CLAD
    Test Engineer
    Solved!
    Go to Solution.

    Hi,
    You could use either.  Whichever you are more comfortable with really.  The STM method will have slightly less overhead over my XML style of tagging the data but it will be very little given the data size.  Probably go with STM as it just has most of the work done for you.
    In terms of data size the way you should normally transfer data like this is to flatten to string.  If you convert to a string of human readable numbers you will either lose precision, increase size or both.  Given that, the string after being flattened will be the same size as the original array anyway so quick calculation based on your previous post 500,000 doubles (8 bytes) is 4 miB (3.8MB)
    Cheers, 
    James Mc
    ========
    CLA and cRIO Fanatic
    wiresmithtech.com/blog

  • Dynamic bandwidth selection for PPPoE over Ethernet/VLAN

    Hello all, hope you are doing great.
    I'm planning to deploy PPPoE Server (Cisco Router 7609) for a ISP. This ISP will provide Internet connection for customer over Ethernet.
    I have to provide a solution to assign bandwidth to each customer by RADIUS and I find some clues that Dynamic Bandwidth Selection (DBS) should be the answer. Unfortunately, DBS only support PPPoA or PPPoE over ATM.
    If you have any experience with equivalent function, please help me. Thank you very much.
    Regards,
    Hiep Nguyen.

    Hiep,
    I think I have figured this out.  Here is the test config on my PPPoE server:
    int lo1
      ip address 172.25.25.25 255.255.255.255
    ip radius source-interface Loopback1
    aaa new-model
    radius-server host 172.16.1.55 auth-port 1812 acct-port 1813 key cisco$$$
    aaa group server radius RADIUS-ACT
     server 172.16.1.55 auth-port 1812 acct-port 1813  
    aaa authentication login default group RADIUS-ACT local
    aaa authorization exec default group RADIUS-ACT local
    aaa accounting exec default start-stop group RADIUS-ACT
    aaa accounting delay-start
    aaa authentication ppp default if-needed group RADIUS-ACT local
    aaa authorization network default group RADIUS-ACT local
    aaa accounting network default start-stop group RADIUS-ACT
    aaa accounting update periodic 5
    bba-group pppoe global
     virtual-template 1
    interface fa0/1
     pppoe enable group global
     ip address 172.30.0.1 255.255.0.0
     no shut
    interface Virtual-Template1
     mtu 1492
     ip unnumbered FastEthernet0/1
     peer default ip address pool GLOBALPOOL
     ppp authentication chap
    ip local pool GLOBALPOOL 172.30.0.2 172.30.127.255
    policy-map POLICE-128K
     class class-default
        police 128000
    policy-map POLICE-512K
     class class-default
        police 512000
    Here are the attributes on the radius server, for a group the PPPoE customer belonged to:
    Service-Type = Framed
    Framed-Protocol = PPP
    cisco-avpair="ip:sub-policy-In=POLICE-128K"
    cisco-avpair+="ip:sub-policy-Out=POLICE-512K"
    Here is the show policy-map on the virtual-access interface the client connected on:
    sho policy-map int virtual-a 3
     Virtual-Access3
      Service-policy input: POLICE-128K
        Class-map: class-default (match-any)
          1000 packets, 1402000 bytes
          5 minute offered rate 0 bps, drop rate 0 bps
          Match: any
          police:
              cir 128000 bps, bc 4000 bytes
            conformed 799 packets, 1120198 bytes; actions:
              transmit
            exceeded 201 packets, 281802 bytes; actions:
              drop
            conformed 0 bps, exceed 0 bps
      Service-policy output: POLICE-512K
        Class-map: class-default (match-any)
          911 packets, 1137746 bytes
          5 minute offered rate 0 bps, drop rate 0 bps
          Match: any
          police:
              cir 512000 bps, bc 16000 bytes
            conformed 799 packets, 1136178 bytes; actions:
              transmit
            exceeded 0 packets, 0 bytes; actions:
              drop
            conformed 0 bps, exceed 0 bps
    I was able to generate enough traffic with ping to meet the exceed action in and have it drop packets.

  • Will AIR ac power cord work for Mac Book Pro?

    will AIR ac power cord work for Mac Book Pro? I've lost my MBP cord.

    No. It does not provide sufficient power for a MBP unless you have a 13" model that uses a 60 watt adaptor.

  • Macbook air 2013 needs power button pressed for 10 seconds before it turns on?

    macbook air 2013 needs power button pressed for 10 seconds before it turns on? also I've tried resting PRAM but when i press the 4 buttons before the start up screen it never restarts again? please help!

    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
    If this does not help, contact Apple.
    Genius Bar reservation:
    http://www.apple.com/retail/geniusbar/
    Best.

Maybe you are looking for