Problem acquiring data with cFP-AI-100

The vi we are trying to design is very simple, just trying to acquire 2 channels, however the sensors in question have both a high and low output, so I have written the VI to acquire 2 channels, one for the high and one for the low of each sensor, and used the express formula function to obtain the difference between them, multiplied by a number to give us a true pressure. We do get a signal bouncing around 0, but don't seem to be acquiring anything other then backround noise.
I've attached the VI as this is my first attempt at working with compact fieldpoint, so I just want to see where i've made my mistake
Attachments:
FTV Pressure.vi ‏286 KB

What kind of sensor are you connected to? Why are you wiring the high of a sensor to one channel and the low to another channel? The cFP-AI-100 uses single ended inputs relative to a common ground. If you don't tie one side of the signal to Common, the single lead is going to have a floating voltage level. The channels are isolated from each other so there is no voltage reference from one lead to the other.
Here is a link to the manual. http://www.ni.com/pdf/manuals/370278a.pdf

Similar Messages

Can I acquire data with VB from my DAQCard without using Measurment Studio?

I have the Measurement and Automation Software on my computer and VisualBasic.NET. Do I need any other software if I am receiving 2 analog signals and outputing 1 analog signal on my NI DAQCard-6024E PCMCIA?

The short answer is yes, you can acquire data with VB.NET from your DAQCard without using Measurement Studio.
There are a variety of ways to do it. All of them require that you install either the Traditional DAQ driver or the DAQmx driver in addition to Measurement and Automation Explorer. The DAQ drivers are included on a CD or CDs with your hardware. They are also available on the quarterly National Instruments Device Driver CD.
1) You can use the Measurement Studio DAQmx .NET API. This is far and away the easiest API to use to program DAQ cards in VB.NET and C#. This API is included in the DAQ installer and does not require you to purchase Measurement Studio. However, without Measurement Studio you do not get the benefit of the DAQ Assistant integrated into Visual Studio .NET. The DAQ Assistant, when integrated into Visual Studio .NET, allows you to graphically configure your DAQ tasks, generates the code you need to configure your tasks, and generates a .NET user control (with user interface) that demonstrates how you use the tasks that you created. The caveat to this approach is that PCMCIA cards are not directly supported under DAQmx 7.0. There is, however, a beta versin of DAQmx PCMCIA support as described in this KB article.
2) You can use the .NET P/Invoke services to call the Traditional DAQ or DAQmx C API directly. See MSDN for more information about P/Invoke. If you choose the DAQmx API, you will need to install the beta of the PCMCIA support as described in this KB article. National Instruments does not provide any examples, language-specific documentation, or code generation for this method. You'll need to look at the C API documentation to see what to do.
3) You can use the Measurement Studio Traditional DAQ ActiveX controls. These are included in the DAQ installer and do not require you to purchase Measurement Studio.
The absolute quickest and easiest way to get started using an NI-DAQ card in VB.NET is through the DAQ Assistant and Measurement Studio Professional or Enterprise edition.
Your next best approach is to use the native .NET DAQmx API. This API was designed from the ground up to support .NET languages. There are examples written in VB.NET to help you get started.
If for some reason, you don't want to use the native .NET API (or your hardware is not supported under DAQmx), whether you use P/Invoke or the ActiveX controls is a toss-up. It depends mostly on whether you are already familiar with the C API or the ActiveX API.
David Rohacek
National Instruments

Problem download data with trailing blanks using gui_download

Hi All,
      I am using SAP 4.6C. I have requirement to download data with trailing
blanks.But i am not succeeded fully to acheive my requirement.I want to
download data to be in the below format.
Eg: 'T000000070600000004000000003593593                                               '
I want to download data with different blanks of each record.
For example in 1 line 18, 2nd line 25, 3rd line 22.
I already used Hexa notation value '09'. But it is showing only 7 at once. I have
added 3 times this field but it is showing 21. How i can i add extra space?
I tried to move ' ' spaces also. It does't wotk. I have tried concatenate with ' ' and
separared by ' ' also but no use.
I have passed all possible parameters to GUI_DOWNLOAD FM.
say write_field_separator         = ' '
write_lf    = 'X'
trunc_trailing_blanks    = ' '
trunc_trailing_blanks_eol     = ' '
Could please tell me some one had faced same problem earlier. It is very urgent.
Is there is any class attribute in SAP 4.6C?
( like cl_abap_char_utilities in 4.7 )
Thanks in Advance.
Basha

Try :
CONCATENATE XXXX space RESPECTING BLANKS.
Of course you must retain these parameters :
trunc_trailing_blanks = space
trunc_trailing_blanks_eol = space
Hope this helps

Problem posting data with HttpsConnection

Hi,
I am currently having problems posting data using a HttpsConnection.
I am setting the setRequestMethod to HttpConnection.POST and then using the openDataOutputStream method.
I will post my code when I get home for reference.
Background to my problem - I am trying to use the declarative security features of J2EE to authenticate a mobile user.
I am firstly firing a HttpsConnection from the mobile device to a protected resource on the app server. I grab the JSessionId from the Set-Cookie http header of the response and post a second request to the j_security_check and provide the refer http header to the protected resource - this simulates exactly what happens on a browser (I used a Http monitor tool to confirm this). However, I need to pass the j_username and j_password as body of the https request. This doesn't seem to work because the server displays my access denied at this point - as if it hadn't received the crednetials
However, just to confirm my technique works I subsituted the post request for a get request to j_security_check and passed the j_username and j_password as request params in the URL. This worked fine and I got a 302 response 'temporily moved' which I then handle by simply making a further request for the original resource - this time it serves back the resource because I am authenticated.
Anyway that sets the scene - so the problem definitely appears to be posting data using an HttpsConnection.
Any help would be greatly appreciated
Rgds,
David

Hi,
Here is my code relating to the above problem:
httpsConn = (HttpsConnection)Connector.open("https://127.0.0.1:8443/ebank/j_security_check");
            httpsConn.setRequestMethod(HttpConnection.POST);
            httpsConn.setRequestProperty("referer", "https://127.0.0.1:8443/ebank/main/mainMenu.xml");
            httpsConn.setRequestProperty("cookie", cookieValue);
            httpsConn.setRequestProperty("location", url);
            httpsConn.setRequestProperty("User-Agent",
                "Profile/MIDP-1.0, Configuration/CLDC-1.0");
            httpsConn.setRequestProperty("Content-Language",
                "en-gb");
String credentials = "j_username=EB0001&j_password=240589";
            httpsConn.setRequestProperty("Content-Length",""+credentials.length());
            DataOutputStream os = httpsConn.openDataOutputStream();
            os.writeUTF(credentials);
....Thanks,
David

Problem sending data with HTTPS using client authentication.

Hi,
I�m tryingto send a message to a secure server using for this client certificate, apparently if I make a GET of "/" (server root) , everything works fine (authentication, and data received), from the moment that I try to ways send data to the "/pvtn " directory i obtain the following error.
This is a sample of the code i�m using:
import com.sun.net.ssl.KeyManagerFactory;
import java.io.BufferedReader;
import java.io.InputStreamReader;
import java.io.OutputStreamWriter;
import java.io.Writer;
import java.net.Socket;
import java.security.*;
import java.security.GeneralSecurityException;
import java.security.Principal;
import java.security.PublicKey;
import java.util.Collection;
import java.util.Date;
import javax.net.ssl.SSLSocket;
import javax.net.ssl.SSLSocketFactory;
import javax.security.cert.*;
import javax.security.cert.X509Certificate;
public class Test
public static final String TARGET_HTTPS_SERVER = "mymachine.mydomain.pt";
public static final int TARGET_HTTPS_PORT = 443;
public static void main(String[] args) throws Exception
System.setProperty("javax.net.ssl.trustStore","/certificados/truststore.txt");
System.setProperty("javax.net.ssl.trustStorePassword","trustpwd");
System.setProperty("javax.net.ssl.keyStore","/certificados/truststore.txt");
System.setProperty("javax.net.ssl.keyStorePassword","trustpwd");
java.security.Security.removeProvider("SunJSSE");
java.security.Security.insertProviderAt(new com.sun.net.ssl.internal.ssl.Provider(),2);
KeyManagerFactory kmf= KeyManagerFactory.getInstance("SunX509", "SunJSSE") ;
//Socket
SSLSocket jsslSoc = (SSLSocket) SSLSocketFactory.getDefault().createSocket(TARGET_HTTPS_SERVER, TARGET_HTTPS_PORT);
String [] ciphers = jsslSoc.getSupportedCipherSuites() ;
//// Select the ciphers you want and put them.
//// Here we will put all availabel ciphers
jsslSoc.setEnabledCipherSuites(ciphers);
//// We are creating socket in client mode
jsslSoc.setUseClientMode(true);
//// Do SSL handshake
jsslSoc.startHandshake();
// Print negotiated cipher
System.out.println("Negotiated Cipher Suite: " + jsslSoc.getSession().getCipherSuite());
System.out.println("");
X509Certificate[] peerCerts = ((javax.net.ssl.SSLSocket)jsslSoc).getSession().getPeerCertificateChain();
if (peerCerts != null)
System.out.println("Printing server information:");
for(int i =0; i < peerCerts.length; i++)
System.out.println("Peer Certificate ["+i+"] Information:");
System.out.println("- Subject: " + peerCerts.getSubjectDN().getName());
System.out.println("- Issuer: " + peerCerts[i].getIssuerDN().getName());
System.out.println("- Version: " + peerCerts[i].getVersion());
System.out.println("- Start Time: " + peerCerts[i].getNotBefore().toString());
System.out.println("- End Time: " + peerCerts[i].getNotAfter().toString());
System.out.println("- Signature Algorithm: " + peerCerts[i].getSigAlgName());
System.out.println("- Serial Number: " + peerCerts[i].getSerialNumber());
else
System.out.println("Failed to get peer certificates");
try
Writer out = new OutputStreamWriter(jsslSoc.getOutputStream(), "ISO-8859-1");
//THIS WAY WORKS FINE
out.write("GET / HTTP/1.1\r\n");
// HERE COMES THE TROUBLES
//out.write("GET /pvtn?someparameter=paramvalue HTTP/1.1\r\n");
out.write("Host: " + TARGET_HTTPS_SERVER + ":" + TARGET_HTTPS_PORT + "\r\n");
out.write("Proxy-Connection: Keep-Alive\r\n");
out.write("User-Agent: SSL-TEST \r\n");
out.write("\r\n");
out.flush();
BufferedReader in = new BufferedReader(new InputStreamReader(jsslSoc.getInputStream(), "ISO-8859-1"));
String line = null;
while ((line = in.readLine()) != null)
System.out.println(line);
finally
jsslSoc.close();
the ssl log until sending the GET is
main, WRITE: SSL v3.1 Handshake, length = 36
main, READ: SSL v3.1 Change Cipher Spec, length = 1
main, READ: SSL v3.1 Handshake, length = 36
Plaintext after DECRYPTION: len = 36
0000: 14 00 00 0C 71 AB 40 CC 6C 33 92 05 E9 69 4B 8F [email protected].
0010: D1 77 3F 6E 3C DB F0 A0 B7 9C CF 49 B6 6D C8 17 .w?n<......I.m..
0020: 7E 03 52 14 ..R.
*** Finished, v3.1
verify_data: { 113, 171, 64, 204, 108, 51, 146, 5, 233, 105, 75, 143 }
%% Cached client session: [Session-1, SSL_RSA_WITH_RC4_128_SHA]
[read] MD5 and SHA1 hashes: len = 16
0000: 14 00 00 0C 71 AB 40 CC 6C 33 92 05 E9 69 4B 8F [email protected].
Negotiated Cipher Suite: SSL_RSA_WITH_RC4_128_SHA
When i send the GET
Plaintext before ENCRYPTION: len = 247
0000: 47 45 54 20 2F 70 76 74 6E 3F 41 30 33 30 3D 4D GET /pvtn?A030=M
main, WRITE: SSL v3.1 Application Data, length = 247
main, READ: SSL v3.1 Handshake, length = 24
Plaintext after DECRYPTION: len = 24
*** HelloRequest (empty)
%% Client cached [Session-1, SSL_RSA_WITH_RC4_128_SHA]
%% Try resuming [Session-1, SSL_RSA_WITH_RC4_128_SHA] from port 3535
*** ClientHello, v3.1
RandomCookie: GMT: 1131988975 bytes = { 45, 113, 241, 212, 81, 255, 244, 169, 74, 41, 160, 227, 197, 210, 155, 211, 47, 237, 18, 179, 238, 47, 28, 86, 30, 253, 157, 253 }
Session ID: {208, 18, 243, 174, 216, 156, 80, 201, 121, 136, 63, 162, 31, 196, 186, 95, 193, 143, 238, 172, 173, 79, 64, 219, 17, 149, 14, 138, 53, 95, 18, 96}
Cipher Suites: { 0, 5, 0, 4, 0, 9, 0, 10, 0, 18, 0, 19, 0, 3, 0, 17, 0, 2, 0, 1, 0, 24, 0, 26, 0, 27, 0, 23, 0, 25 }
Compression Methods: { 0 }
[write] MD5 and SHA1 hashes: len = 105
Plaintext before ENCRYPTION: len = 125
main, WRITE: SSL v3.1 Handshake, length = 125
main, READ: SSL v3.1 Handshake, length = 94
Plaintext after DECRYPTION: len = 94
*** ServerHello, v3.1
RandomCookie: GMT: 1131991620 bytes = { 205, 194, 212, 113, 37, 213, 41, 13, 60, 142, 135, 68, 17, 78, 227, 251, 176, 211, 133, 203, 153, 173, 153, 195, 93, 7, 87, 123 }
Session ID: {108, 85, 45, 208, 104, 124, 209, 24, 247, 113, 156, 134, 28, 154, 75, 198, 64, 181, 167, 9, 149, 223, 162, 21, 225, 32, 168, 31, 190, 48, 241, 195}
Cipher Suite: { 0, 5 }
Compression Method: 0
%% Created: [Session-2, SSL_RSA_WITH_RC4_128_SHA]
** SSL_RSA_WITH_RC4_128_SHA
[read] MD5 and SHA1 hashes: len = 74
main, READ: SSL v3.1 Handshake, length = 3154
Plaintext after DECRYPTION: len = 3154
*** Certificate chain
stop on trusted cert: [
Version: V1
Subject: CN=GTE CyberTrust Global Root, OU="GTE CyberTrust Solutions, Inc.", O=GTE Corporation, C=US
Algorithm: [MD5withRSA]
Signature:
[read] MD5 and SHA1 hashes: len = 3134
main, READ: SSL v3.1 Handshake, length = 479
Plaintext after DECRYPTION: len = 479
*** CertificateRequest
Cert Types: RSA, DSS,
Cert Authorities:
[read] MD5 and SHA1 hashes: len = 455
*** ServerHelloDone
[read] MD5 and SHA1 hashes: len = 4
0000: 0E 00 00 00 ....
*** Certificate chain
*** ClientKeyExchange, RSA PreMasterSecret, v3.1
Random Secret: { 3, 1, 19, 223, 230, 65, 59, 210, 10, 69, 239, 178, 185, 5, 52, 57, 44, 160, 163, 239, 85, 64, 173, 16, 132, 234, 33, 228, 0, 8, 134, 52, 20, 190, 196, 15, 205, 35, 169, 39, 14, 160, 143, 74, 210, 74, 43, 181 }
[write] MD5 and SHA1 hashes: len = 141
Plaintext before ENCRYPTION: len = 161
main, WRITE: SSL v3.1 Handshake, length = 161
SESSION KEYGEN:
PreMaster Secret:
.CONNECTION KEYGEN:
Client Nonce:
Server Nonce:
Master Secret:
Client MAC write Secret:
Server MAC write Secret:
Client write key:
Server write key:
0000: FE 94 DF 4C 1A 9F FA CE 0C E9 A6 DB 31 53 E5 FD ...L........1S..
... no IV for cipher
Plaintext before ENCRYPTION: len = 21
0000: 01 0D 16 E6 49 18 36 AF E1 52 9C 2F 72 EE CA DF ....I.6..R./r...
0010: 41 71 68 30 06 Aqh0.
main, WRITE: SSL v3.1 Change Cipher Spec, length = 21
*** Finished, v3.1
verify_data: { 243, 49, 247, 150, 113, 86, 182, 125, 244, 163, 245, 243 }
[write] MD5 and SHA1 hashes: len = 16
0000: 14 00 00 0C F3 31 F7 96 71 56 B6 7D F4 A3 F5 F3 .....1..qV......
Plaintext before ENCRYPTION: len = 36
0000: 14 00 00 0C F3 31 F7 96 71 56 B6 7D F4 A3 F5 F3 .....1..qV......
0010: 1A 7C 8F D9 51 CB 6F 47 2A 7C 90 81 20 EE 97 64 ....Q.oG*... ..d
0020: FF 47 35 CA .G5.
main, WRITE: SSL v3.1 Handshake, length = 36
main, SEND SSL v3.1 ALERT: warning, description = close_notify
Plaintext before ENCRYPTION: len = 22
0000: 01 00 F0 F4 AC 3C B2 DE 95 98 0E B4 ED B1 24 3B .....<........$;
0010: 54 6C 8B DC F3 1F Tl....
main, WRITE: SSL v3.1 Alert, length = 22
java.net.SocketException: Connection aborted by peer: socket write error
     void java.net.SocketOutputStream.socketWrite(java.io.FileDescriptor, byte[], int, int)
          native code
     void java.net.SocketOutputStream.write(byte[], int, int)
          SocketOutputStream.java:96
     void com.sun.net.ssl.internal.ssl.OutputRecord.a(java.io.OutputStream)
     void com.sun.net.ssl.internal.ssl.SSLSocketImpl.a(com.sun.net.ssl.internal.ssl.OutputRecord)
     void com.sun.net.ssl.internal.ssl.HandshakeOutStream.flush()
     void com.sun.net.ssl.internal.ssl.Handshaker.sendChangeCipherSpec(com.sun.net.ssl.internal.ssl.HandshakeMessage$Finished)
     void com.sun.net.ssl.internal.ssl.ClientHandshaker.c()
     void com.sun.net.ssl.internal.ssl.ClientHandshaker.a(com.sun.net.ssl.internal.ssl.SunJSSE_o)
     void com.sun.net.ssl.internal.ssl.ClientHandshaker.processMessage(byte, int)
     void com.sun.net.ssl.internal.ssl.Handshaker.process_record(com.sun.net.ssl.internal.ssl.InputRecord)
     void com.sun.net.ssl.internal.ssl.SSLSocketImpl.a(com.sun.net.ssl.internal.ssl.InputRecord, boolean)
     void com.sun.net.ssl.internal.ssl.SSLSocketImpl.a(com.sun.net.ssl.internal.ssl.InputRecord)
     int com.sun.net.ssl.internal.ssl.AppInputStream.read(byte[], int, int)
     int java.io.InputStream.read(byte[])
          InputStream.java:91
     int java.io.InputStreamReader.fill(char[], int, int)
          InputStreamReader.java:173
     int java.io.InputStreamReader.read(char[], int, int)
          InputStreamReader.java:249
     void java.io.BufferedReader.fill()
          BufferedReader.java:139
     java.lang.String java.io.BufferedReader.readLine(boolean)
          BufferedReader.java:299
     java.lang.String java.io.BufferedReader.readLine()
          BufferedReader.java:362
     void Teste3.main(java.lang.String[])
          Teste3.java:109
Exception in thread main
Debugger disconnected from local process.
Process exited with exit code 1.
One more thing if if make the same thing via browser (https://mymachine.mydomain.pt/pvtn?someparameter=somevalue) and works fine too (obviously i pre installed the client certificate in the browser and choose the certificate when the pop up show up)
It seems like the handshaking fails when i send data to /pvtn...
Regards,
Paulo.

I amhaving the another problem very similar, I am struggling with client authentication with IIS 5.0, and receiving the 'Remote Host closed the connection' error.
Is there any help me in this. I truly apprecaite it
Thanks

Problem increasing dates with REGEXP_REPLACE and TO_DATE

Hello all,
i'm trying to increase dates in a string with a single statement, but i ran into the problem that Oracle doesn't interpret the regex backtrace operators when they are used in TO_DATE:
SELECT
REGEXP_REPLACE(
    'Test: 01.01.2001 Test: 02.02.2002',
    '([0-9]{2})\.([0-9]{2})\.([0-9]{4})',
    TO_CHAR(TO_DATE('\1\2\3', 'DDMMYYYY') + 1, 'DD.MM.YYYY')
FROM DUALLeads to a ORA-01858: 01858, 00000, "a non-numeric character was found where a numeric was expected".
However, using other functions on the backtrace operators like UPPER('\1') works like a charm. Is this a limitation of the TO_DATE function?
Is there any possibility to replace the dates in a small, simple statement?
Thanks in advance,
-sd

How should I show you an example, when it's simply
not possible? I know I mixed up parameters and
callbacks mistakenly and took the wrong approach.Ok. In your last post, you've added a question mark, so
it did look as you weren't aware of the problem.
However, I thought there was some possibility in
Oracle regex to apply a callback function to
regex-replacement like other languages have
(preg_replace_callback in PHP for example) like:Interesting. Unfortunately PL/SQL is not PHP and there's
(yet) no callback feature implemented.
FUNCTION chg_date(
p_string
REGEXP_REPLACE_CALLBACK('Test: 2001', '[0-9]{4}',
'chg_date')
...I too miss the possibility to extend the use of backtrace
parameters, maybe in one of the future versions.
C.

Problem loading data with DTP

Hi everyone,
I trying to load data from a DSO to a INFOCUBE, the problem is as follow. Normally in a DTP the system process packages in the request. In this case the DTP don't proccess any package but finish with status green.
When I manage the target, I see that the request finish in red.
The symptom is that the DTP don't process any request. I don´t know why.
Status: The DSO have active data, and the infocube is empty.
I don't know what happen, but I've not carry the data from the DSO to the target.
I hope that you help me,
Regards.
Jose

Answering your questions:
Are you seeing the request red in Manage and Green in Monitor Details ?
Yes in manage I see the requests in red, but in the monitor details all is in green, although there are not requests processed in the monitor details..
Are the requests green and active in the source DSO ?
Ok, this DSO is direct input, an it's filled by a APD process. So the DSO don't have active request. This DSO Just have the data in table of active data. I think that it doesn't matter because I'm trying to do the same thing between two infocubes and doesn't work too.
I'm looking that the problem y general for all warehouse.
Additional, this DTP works correct the last week.
This week begins to fail.
Could be a System problem.
What can I check??
Also check if this is an auth issue - SU53 ..
I check SU53 but all it's ok.
In Monitor Header - Selections - You should see the requests which have been loaded from source.
I don't see anything in this field.
Thanks
Jose

Problems acquiring images with IMAQ-1408

I have a IMAQ-1408 acquisition card that I recently transplanted from an old computer to a new P4. Initially, it did record a few images (both in one of my programs and using the test panels in the Measurement and Automation Explorer. Now it doesn't acquire. I have tried several things like switching PCI slots, adjusting some of the settings like the sync voltage levels and such, but I'm not getting any images. All 6 diagnositc tests past (from 'FPGA register' to 'Basic interrupt'). Also, the card is still detecting something - when I connect to a video source, I get the error ... when I have it disconnected from the video, it gives an IMG-ERR-VLCK. So it must be detecting some of the V-synch pulses. Anyway, at what poi
nt do I decide that my card is non-functional? Are there any more setting adjustments I should try. (BTW, I'm using an NTSC source).
thanks

This issue is sounding more like a hardware problem if the diagnostics fail repeatedly. Before considering repair or purchasing a new board, I still recommend testing the card in another machine just to be thorough.
The board most likely can be repaired (I'm not sure about the cost, since it is most likely out of warranty). Otherwise, the PCI-1409 board is similar to the 1408, but has several advantages. Please see this KnowledgeBase for more information on the differences. If you are interested in the repair/replacement options, please generate a service request to speak directly with an engineer. You can generate a request online at "http://www.ni.com/ask">www.ni.com/ask. This will allow us to set up an RMA if need be.
Regards,
Jesse D.
Applications Engineer
National Instruments

Numerisation of Acquired Data and Transforming into Frequency domain to process it with some mathematical expressions

Hi everyone,
I've been trying to manage some signal processing stuff, I use mathscript node for it; due to the node, i have to transform the data set into numerical values. Due to my research, i should do my processing in frequency domain.
I did a VI, but i dont think it will work properly when i will use it with acquired data. The VI in the attachment has four dummy-signal sources, sines, consider these as analog input channels. The main question is actually how to process acquired data with numerical operations. And how to properly transform the time domain series into "numerical" frequency domain array.
Take a look at the example in the attachment. The other one is mathematical expression of the process.
Thanks,
OZGUR
Attachments:
sample.vi ‏204 KB
mathematical.png ‏103 KB

Motorbreath,
Here are some examples on how to use LabVIEWs graphcial coding to get things into the Frequency domain:
https://decibel.ni.com/content/docs/DOC-9981
http://zone.ni.com/devzone/cda/tut/p/id/13042
http://zone.ni.com/devzone/cda/tut/p/id/7111
http://zone.ni.com/devzone/cda/epd/p/id/2904
But essentially you are going to want to use the FFT VIs
http://zone.ni.com/devzone/cda/tut/p/id/4278
http://zone.ni.com/devzone/cda/tut/p/id/4541
http://zone.ni.com/devzone/cda/tut/p/id/3342
https://decibel.ni.com/content/docs/DOC-6390
I hope this gets you going
Sam S
Applications Engineer
National Instruments

Acquiring data continuously with a start and stop trigger

I am currently acquiring data continuously (1000 samples at 5k/s) using a start trigger to start the acquisition and stopping the acquisition with a digital line. The problem with this is that I want the acquisition to stop immediately on a trigger, in otherwords I don't want it to finish with 500 or 200 samples of useless data. I am using a PCI 6024 E. Any suggestions would be appreciated.

The trick will be to minimize the number of post-trigger scans that will occur after your stop trigger. The stop (reference) trigger requires a minimum of 2 post-triggered scans. Therefore, the way to stop your acquisition as soon as possible is to configure your stop trigger to have only 2 post-triggered scans.
I've included a little bit of code to illustrate this in LabVIEW 7.0. The number of post-trigger scans will equal the buffer size less the number of pre-trigger scans. Since the minimum number of post-triggered scans is 2, we'd have to set the number of pre-trigger scans to the buffer size less 2. This is wired as the minimum number of pre-trigger scans acquired input to the AI Control.vi in the example.
This should do what you're
after. Best of luck to you as you get this all put together.
Jim Laudie
Applications Engineer, National Instruments
Attachments:
example.vi ‏85 KB

Oracle OCI: Problem in Query with Date field

Client compiled with OCI: 10.2.0.4.0
Server: Oracle9i Enterprise Edition Release 9.2.0.4.0
The problematic query is:
SELECT CODIGO FROM LOG WHERE TEL = :telnumber AND DATE_PROC = '05-JUL-08'Table description:
SQL>describe LOG;
TEL NOT NULL VARCHAR2(15)
CODIGO NOT NULL VARCHAR2(20)
DATE_PROC NOT NULL DATEAs simple as it might look, when executed directly on the server with SQLPlus, it returns a result, but when executed from the app that uses OCI, this query returns OCI_NO_DATA always. In the beginning, the date value was also a placeholder, but I found out that even giving a literal like '05-JUL-08' didn't work. I have tried the following:
<ul>
<li>I've tried the basics: querying the DB from the client does work. It's this one that gives me trouble</li>
<li>The query: SELECT CODIGO FROM LOG WHERE TEL = :telnumber does work</li>
<li>Executing: ALTER SESSION SET NLS_DATE_FORMAT="DD-MM-YYYY"; before the query in both the server and the client. Same result: server returns data, client OCI_NO_DATA</li>
<li>Tried changing DATE_PROC format, combining this with the use of TO_DATE(). Same result.</li>
<li>Searched, searched, searched. No answer</li>
</ul>
I'm a bit desperate to find an answer, would appreciate any help and can provide as many further details as needed. Thanks.
Edited by: user12455729 on Jan 15, 2010 5:59 AM. -Formatting-

Hi,
I've recreated your table and populated with your data.
I've run your select using OCILIB on a 10gR2 (client and server) and the codes runs fine and give expected results.
So the problem must resides in your code.... (i don't think it can be a OCI bug)
Here is the ocilib code :
#include "ocilib.h"
int main(void)
    OCI_Connection *cn;
    OCI_Statement *st;
    OCI_Resultset *rs;
    char msisdn[100] = "11223344";
    char datetime[100] = "";
    if (!OCI_Initialize(err_handler, NULL, OCI_ENV_DEFAULT))
        return EXIT_FAILURE;
    cn = OCI_ConnectionCreate("db", "usr", "pwd", OCI_SESSION_DEFAULT);
    st = OCI_StatementCreate(cn);
    OCI_Prepare(st, "SELECT "
                    " CODIGO_BANCO "
                    "FROM "
                    " VTA_LOG "
                    "WHERE "
                    " TELEFONO = :msisdn AND "
                    " FECHA_PROCESO = TO_DATE(:datetime, 'YYYYMMDDHH24MISS')");
    OCI_BindString(st, "msisdn", msisdn, sizeof(msisdn)-1);
    OCI_BindString(st, "datetime", datetime, sizeof(datetime)-1);
    strcpy(datetime, "20080705162918");
    OCI_Execute(st);
    rs = OCI_GetResultset(st);
    OCI_FetchNext(rs);
    printf("%s\n", OCI_GetString(rs, 1));
    strcpy(datetime, "20080705062918");
    OCI_Execute(st);
    rs = OCI_GetResultset(st);
    OCI_FetchNext(rs);
    printf("%s\n", OCI_GetString(rs, 1));
    OCI_Cleanup();
    return EXIT_SUCCESS;
}Output is :
BancoOne
BancoTwoi recreated your data with
create table VTA_LOG
     TELEFONO          VARCHAR2(15) NOT NULL ,
     CODIGO_BANCO     VARCHAR2(20) NOT NULL ,
     FECHA_PROCESO     DATE NOT NULL
insert into VTA_LOG values ('11223344', 'BancoOne', to_date('20080705162918', 'YYYYMMDDHH24MISS'));
insert into VTA_LOG values ('11223344', 'BancoTwo', to_date('20080705062918', 'YYYYMMDDHH24MISS'));
commit;Regards,
Vincent

Failed to acquire DAS with data sources that match the specified OCE

Please help, Thank you all.
We are migrating Oracle databases from Windows to Linux servers. Currently, I have no problem to use my desktop Hyperion Intelligence Designer 8.5 with new oce file to connect to Linux. However, I published the same oce file to Hyperion Performance Suite 8.5 then I got “Sever Error [2018]: Failed to acquire Data Access Service with data sources that match the specified OCE”.
I launched Service Configurator, in the “Local Service Configurator - DAS1_host”, the “Database JDBC URL is point to Linux server. Also, I added ODBC connection to Oracle database on Linux in the “Properties of Data Access Service: DAS1_host’s Data Source”. Database of JDBC URL in BI1_host, AZ1_host, PUB1_host, SM1_host, LS1_host, UT1_host, BPS1_host, AN1_host are also point to Linux server.
The “Remote Service Configurator” has ES1_host’s” Storage” with JDBC URL point to Linux server. The same for RM1_host’s and NS1_host’s “Storage” with JDBC URL point to Linux server.
Is there some missing configuration on the server? Thank you in advance.

You should login to my oracle support to look into this ID.
This is the solution mentioned
Solution
1) In the .profile file, you will find the definition of the LD_LIBRARY_PATH variable. However, the path to 64 bit libraries is probably appended before the path to the 32 bit libraries(%ORACLE_HOME%/lib32). Therefore, please reverse the order in the definition so that the 32 bit libraries get loaded before the 64 bit libraries.
Then, restart all services.
2) Oracle 9.2 was the first Oracle release which defaults to using the 64 bit libraries in the 'lib' directory and the 32-bit libraries that we need are in the 'lib32' directory.
Therefore, please have the%ORACLE_HOME%/lib32 placed in front of the LD_LIBRARY_PATH environment variable definition.Then, restart all services.
3) Please check that users have read and write access to the files located in the %ORACLE_HOME%/lib32 folder.
4) Check the permissions of the libclntsh.a file(located in the %ORACLE_HOME%/lib32 folder) are set to rwxr-xr-x
5) Recreate the OCE connection in DAS and restart DAS in CMC.
6) Restart all the BIPlus Services and process the query.

Compairing a db record date with a dynamic calendar to make date into a hyperlink problem. Please help

Hello;
I need help. I have a dynamic calendar I have been writting. (I realize there are lots of free ones online but I needed one to do something else. this is only a part of the whole.I have everyhting working fine, it advances to the next month and looks really nice.I can't get my query to work. I had it throwing an error, but now it is just spitting out data I didn't want.I will post the code that is the problem, then the whole code for the calendar.
This is the problem code:
<cfset firstOfTheMonth = createDate(year(now()), month(now()), 1)>
<cfset endOfTheMonth = createdatetime(year(now()), month(now()), #daysinmonth(firstOfTheMonth)#, 23, 59, 59)>
<cfquery name="CaleventRec" datasource="#APPLICATION.dataSource#">
SELECT events.eventDate, events.ID AS ID
FROM events
Where eventDate Between #firstOfTheMonth# and #endOfTheMonth#
</cfquery>
<cfoutput>
<cfif thisday is day(now())>
        <b>#ThisDay#</b>
    <cfelse>
        <cfif listFind(days,thisday)>
            <a href="##"><b>thisday</b></a>
        <cfelse>
            #thisday#
        </cfif>
    </cfif>
</cfoutput>
this is the whole code for the calendar part:

       <cfparam name = "month" default = "#DatePart('m', Now())#">
<cfparam name = "year" default = "#DatePart('yyyy', Now())#">
<cfparam name = "currentday" default = "#DatePart('d', Now())#">
<cfparam name = "startmonth" default = "#DatePart('m', Now())#">
<cfparam name = "startyear" default = "#DatePart('yyyy', Now())#">

<cfset ThisMonthYear = CreateDate(year, month, '1')>
<cfset Days = DaysInMonth(ThisMonthYear)>

<cfset LastMonthYear = DateAdd('m', -1, ThisMonthYear)>
<cfset LastMonth = DatePart('m', LastMonthYear)>
<cfset LastYear = DatePart('yyyy', LastMonthYear)>
<cfset NextMonthYear = DateAdd('m', 1, ThisMonthYear)>
<cfset NextMonth = DatePart('m', NextMonthYear)>
<cfset NextYear = DatePart('yyyy', NextMonthYear)>
<cfset PreviousDay = DateAdd('d', -1, ThisMonthYear)>
<cfset CurrentYear = DatePart('yyyy', Now())>
       <table border="0" width="100%" bgcolor ="#ffffff">
            <tr>
                <td align = "center" valign="top">
                    <table border="0" width="100%" height="100%">
   <tr>
      <th align="center" colspan="7" bgcolor="#2b4e6e">
   <cfoutput>
   <table width="100%" border="0" cellspacing="0" cellpadding="0">
      <tr>
        <td width="15%" align="left" valign="middle">
<cfif (LastYear lt CurrentYear) OR (LastYear lte CurrentYear AND LastMonth lt startmonth)>
<cfelse>
  <a href ="index.cfm?month=#LastMonth#&year=#LastYear#" class="calNav">Prev</a></cfif></td>
        <td width="72%" align="center" valign="middle"><FONT SIZE="3" face="Arial, Helvetica, sans-serif" color="##ffffff">#MonthAsString(month)# #year#</FONT></td>
        <td width="13%" align="right" valign="middle">
<cfif (NextYear lt CurrentYear) OR (NextYear lte CurrentYear AND NextMonth lt startmonth)>
<cfelse>
<a href = "index.cfm?month=#NextMonth#&year=#NextYear#" class="calNav">Next</a>  </cfif></td>
      </tr>
    </table></cfoutput></th>
   </tr>
   <tr>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Sun</FONT></td>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Mon</FONT></td>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Tue</FONT></td>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Wed</FONT></td>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Thu</FONT></td>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Fri</FONT></td>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Sat</FONT></td>
   </tr>
<cfset firstOfTheMonth = createDate(year(now()), month(now()), 1)>
<cfset endOfTheMonth = createdatetime(year(now()), month(now()), #daysinmonth(firstOfTheMonth)#, 23, 59, 59)>
<cfquery name="CaleventRec" datasource="#APPLICATION.dataSource#">
SELECT events.eventDate, events.ID AS ID
FROM events
Where eventDate Between #firstOfTheMonth# and #endOfTheMonth#
</cfquery>
<cfset ThisDay = 0>
<cfloop condition = "ThisDay LTE Days">
<tr class = "calendar">
<cfloop from = "1" to = "7" index = "LoopDay">

<cfoutput>
<cfif thisday is day(now())>
        <b>#ThisDay#</b>
    <cfelse>
        <cfif listFind(days,thisday)>
            <a href="##"><b>thisday</b></a>
        <cfelse>
            #thisday#
        </cfif>
    </cfif>
</cfoutput>
<cfif ThisDay IS 0>
<cfif DayOfWeek(ThisMonthYear) IS LoopDay>
<cfset ThisDay = 1>
</cfif>
</cfif>

<cfif (ThisDay IS NOT 0) AND (ThisDay LTE Days)>
<cfoutput>

<cfif (#ThisDay# EQ #currentday#) AND (#month# EQ #startmonth#) AND (#year# EQ #startyear#)>
<td align = "center" bgcolor="##FFFFCC">
<cfset dayview = #dateformat(createdate(#year#, #month#, #thisday#), "mm/dd/yyyy")#>
<font face="Arial, Helvetica, sans-serif" color="##000000" size="2">#ThisDay#</font>
</td>
<cfelse>
<td align = "center">
<cfset dayview = #dateformat(createdate(#year#, #month#, #thisday#), "mm/dd/yyyy")#>
<font face="Arial, Helvetica, sans-serif" color="##000000" size="2">#ThisDay#</font>
</td>
</cfif>
</cfoutput>
<cfset ThisDay = ThisDay + 1>
<cfelse>
<td></td>
</cfif>
</cfloop>
</tr>
</cfloop>
</table>
</td>
</tr>
</table> </td>
</tr>
</table>
Can anyone help me with this? It is the last thing I need to get working and it is driving me crazy. Right now, this code does this:0
0
0
0
1
1
2
2
3
3
and then at the bottom of 32 numbers and doubles of numbers, is the calendar. So my llink code is making it do this.
Thank you!
I have to point out, it's pretty bad when Adobe is using jsp instead of coldfusion to run their forums.???????

I have been doing a lot of reading, and my code seems to be right accept for my where statement on my query that is matching the db date with the calendar date. (I think) This is what I did, and right now I get an error. I also dumped it and my date is posted at the bottom of this message in it's format.
This is my error:
Parameter validation error for the CREATEODBCDATE function.
The value of parameter 1, which is currently mm/dd/yyyy, must be a class java.util.Date value.
The error occurred in C:\website\event\index.cfm: line 157
155 : SELECT events.eventDate, events.ID AS ID
156 : FROM events
157 : WHERE eventDate = #CreateODBCDate("mm/dd/yyyy")#
158 : </cfquery>
ok this is now my code: (I realize it is long, I tried to make it as easy to follow as possible)

       <cfparam name = "month" default = "#DatePart('m', Now())#">
<cfparam name = "year" default = "#DatePart('yyyy', Now())#">
<cfparam name = "currentday" default = "#DatePart('d', Now())#">
<cfparam name = "startmonth" default = "#DatePart('m', Now())#">
<cfparam name = "startyear" default = "#DatePart('yyyy', Now())#">

<cfset ThisMonthYear = CreateDate(year, month, '1')>
<cfset Days = DaysInMonth(ThisMonthYear)>

<cfset LastMonthYear = DateAdd('m', -1, ThisMonthYear)>
<cfset LastMonth = DatePart('m', LastMonthYear)>
<cfset LastYear = DatePart('yyyy', LastMonthYear)>
<cfset NextMonthYear = DateAdd('m', 1, ThisMonthYear)>
<cfset NextMonth = DatePart('m', NextMonthYear)>
<cfset NextYear = DatePart('yyyy', NextMonthYear)>
<cfset PreviousDay = DateAdd('d', -1, ThisMonthYear)>
<cfset CurrentYear = DatePart('yyyy', Now())>
<table border="0" width="100%" bgcolor ="#ffffff">
            <tr>
                <td align = "center" valign="top">
                    <table border="0" width="100%" height="100%">
   <tr>
      <th align="center" colspan="7" bgcolor="#2b4e6e">
   <cfoutput>
   <table width="100%" border="0" cellspacing="0" cellpadding="0">
      <tr>
        <td width="15%" align="left" valign="middle">
<cfif (LastYear lt CurrentYear) OR (LastYear lte CurrentYear AND LastMonth lt startmonth)>
<cfelse>
<a href ="index.cfm?month=#LastMonth#&year=#LastYear#" class="calNav">Prev</a></cfif></td>
        <td width="72%" align="center" valign="middle"><FONT SIZE="3" face="Arial, Helvetica, sans-serif" color="##ffffff">#MonthAsString(month)# #year#</FONT></td>
        <td width="13%" align="right" valign="middle">
<cfif (NextYear lt CurrentYear) OR (NextYear lte CurrentYear AND NextMonth lt startmonth)>
<cfelse>
<a href = "index.cfm?month=#NextMonth#&year=#NextYear#" class="calNav">Next</a> </cfif></td>
      </tr>
    </table></cfoutput></th>
   </tr>
   <tr>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Sun</FONT></td>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Mon</FONT></td>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Tue</FONT></td>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Wed</FONT></td>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Thu</FONT></td>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Fri</FONT></td>
    <td><FONT SIZE="2" face="Arial, Helvetica, sans-serif" color="#333366">Sat</FONT></td>
   </tr><br><br>

<cfquery name="CaleventRec" datasource="#APPLICATION.dataSource#">
SELECT events.eventDate, events.ID AS ID
FROM events
WHERE eventDate = #CreateODBCDate("mm/dd/yyyy")#
</cfquery>

                       
                        <cfset ThisDay = 0>
                        
                        <cfloop condition = "ThisDay LTE Days">
                            <tr>
                            
                            <cfloop from = "1" to = "7" index = "LoopDay">
                            
                                <cfif #PreviousDay# EQ Now() - 1>
                                    <cfoutput query="CaleventRec">
                                        <a href = "cal_day.cfm">#Days#</a>
                                    </cfoutput>
                                </cfif>
                            
                                <cfif ThisDay IS 0>
                                    <cfif DayOfWeek(ThisMonthYear) IS LoopDay>
                                        <cfset ThisDay = 1>
                                    </cfif>
                                </cfif>
                            
                                <cfif (ThisDay IS NOT 0) AND (ThisDay LTE Days)>
                                    <cfoutput>
                                    
                                        <cfif (#ThisDay# EQ #currentday#) AND (#month# EQ #startmonth#) AND (#year# EQ #startyear#)>
                                            <td align = "center">
                                                <cfset dayview = #dateformat(createdate(#year#, #month#, #thisday#), "mm/dd/yyyy")#>
                                                <font class = "calendartoday">#ThisDay#</font>
                                            </td>
                                        <cfelse>
                                            <td align = "center">
                                                <cfset dayview = #dateformat(createdate(#year#, #month#, #thisday#), "mm/dd/yyyy")#>
                                                <font class = "calendar">#ThisDay#</font>
                                            </td>
                                        </cfif>
                                    </cfoutput>
                                    <cfset ThisDay = ThisDay + 1>
                                    <cfelse>
                                        <td></td>
                                </cfif>
                            </cfloop>
                            </tr>
                    </cfloop>
                    </table>
                </td>
            </tr>
        </table>
My date inthe database is like this = 1/1/2009
So my date is in teh DB with no time on it, I used code in the admin section to force an event date to only be allowed to be in that format.
How can I make this work? Is it only my where statement?
Thanks for the help so far.

Problem in scheduling agreement dates with 2LIS_12_VCSCL extractor

I am using 2LIS_12_VCSCL extractor to get the order fulfilment report.
I am using ODS as an infprovider and on BW 3.5.
Scenario on Sale Order screen - VA33 [ Scheduling Agreemnent ]
Sales doc   Item Line-No     Qty      Del NO    Req-Date         Actual GI Date
    100          10      1            10          222        5/10/2008        5/10/2008   ( this is the only item that is delivered)
     ---            --       2            10                       6/10/2008
     ---            --       3            10                       7/10/2008
This Scenario when we view the data in rsa3 by running 2LIS_12_VCSCL
Sales doc   Item Line-No     Qty      Del NO     Req-Date        Actual GI Date
     100       10      1            10           222         5/10/2008         5/10/2008
        ---       2            10          222        6/10/2008          5/10/2008
        ---       3            10          222        7/10/2008           5/10/2008
Note that the delivery no is assigned to the unschedules schedulines(ie; these are open schedulelines that have not been delivered, but the extractor is assigning the first delivery no to all these schedule lines)
We are confused and do not understand if this is how this extractor works . what we actually expected to get is only one recored for which the delivery has been made.
like :
Sales doc   Item Line-No     Qty      Del NO    Req-Date        Actual GI Date
       100       10      1            10          222        5/10/2008        5/10/2008
the other two lines should not get extracted. If this is a bug in the extractor program please point us to the OSS notes or the fix that can be applied.
Else if this is how this extractor works please suggest the fix that can be applied on the BW side to extract only the first record (ie; the schedule line record for which the delivery has been done)
Greatly appreciate help on this issues.
Thank You,
Edited by: Swordfish on May 12, 2008 1:09 PM
Edited by: Swordfish on May 12, 2008 1:21 PM

Hello,
I think we have the same problem. Data pulled over to BW has alot more records for a single delivery.
Anybody have any thoughts on this.

Problem in working with Japanese data

Hello,
We have an application, which should work for both English and Japanese languages. Our application is working fine for English data but in case of Japanese, we are facing problems. In the application, there is a language setting, where the user can select either English or Japanese. This changes the language of the labels to English or Japanese. We are handling this thru' ResourceBundles. But the data that is entered can be independent of this. In English setting also, the data entered or diplayed could be Japanese. Now we are facing problems at vaious places -
1. When we enter Japanese data and save it, it gets copied into the bean and if there is any error in the saving, the same data from bean comes back on the screen. This data doesn't appear properly in Japanese.
2. When we try to retrieve the already saved data from database, it doesn't show poperly in Japanese.
We are using our own 'toUnicode' function, which converts the data to Unicode before saving the data to database. Similarly, we have tried different encodings like SJIS / Shift_JIS / ISO-2022-JP at various places i.e. in 'Page' directive or in HTML Meta tag or various combinations of these two. Nothing is working reliably. Sometimes for some combination, data retained in the first case is correct but it can't be saved. Sometimes it works with Unicode, sometimes without Unicode. Some combination affects the Japanese labels as well. Otherwise the labels at least are displayed properly.
The same code with just Shift_JIS setting in 'page' directive, worked well in IIS Server for both English and Japanese.
What could be the problem in WebLogic? Does it matter if WL is installed on English or Japanese machine?
Kindly answer ASAP, since the project is getting delayed.
Thanking in anticipation...
-Medha

Hi,
is there a difference in handling Japanese and Chinese chars? If not I
might be able to give you some hints.
Daniel
-----Original Message-----
From: JSB [mailto:[email protected]]
Posted At: Monday, February 12, 2001 6:22 PM
Posted To: internationalization
Conversation: Problem in working with Japanese data
Subject: Re: Problem in working with Japanese data
Have u solved this yet, and how ?
Medha <[email protected]> wrote in message
news:[email protected]...
>
Hello,
We have an application, which should work for both English andJapanese
languages. Our application is working fine for English data but in case
of
Japanese, we are facing problems. In the application, there is a
language
setting, where the user can select either English or Japanese. This
changes
the language of the labels to English or Japanese. We are handling this
thru' ResourceBundles. But the data that is entered can be independent
of
this. In English setting also, the data entered or diplayed could be
Japanese. Now we are facing problems at vaious places -
1. When we enter Japanese data and save it, it gets copied into thebean
and if there is any error in the saving, the same data from bean comes
back
on the screen. This data doesn't appear properly in Japanese.
2. When we try to retrieve the already saved data from database, itdoesn't show poperly in Japanese.
We are using our own 'toUnicode' function, which converts the datato
Unicode before saving the data to database. Similarly, we have tried
different encodings like SJIS / Shift_JIS / ISO-2022-JP at various
places
i.e. in 'Page' directive or in HTML Meta tag or various combinations of
these two. Nothing is working reliably. Sometimes for some combination,
data
retained in the first case is correct but it can't be saved. Sometimes
it
works with Unicode, sometimes without Unicode. Some combination affects
the
Japanese labels as well. Otherwise the labels at least are displayed
properly.
The same code with just Shift_JIS setting in 'page' directive,worked
well in IIS Server for both English and Japanese.
What could be the problem in WebLogic? Does it matter if WL isinstalled on English or Japanese machine?
Kindly answer ASAP, since the project is getting delayed.
Thanking in anticipation...
-Medha

Problem acquiring data with cFP-AI-100

Similar Messages

Maybe you are looking for