Problem Cisco Catalyst 3850 input errors

Ive installed two stacked Catalyst 3850s. Connected to these two switches I have a SAN 6210 Equallogic Dell ESX .
The interfaces on the switches is bundels with Port-channel. MTU size 9198. On swich one its no problem but on switch two I see input errors on these interface.
If I move the cables from switch two to one then its ok...
I have two 10G going to the SAN. And 4 ESX server with 2 ISCSI each.
interface Port-channel21
description ESX1 ISCSI SAN
switchport access vlan 21
switchport mode access
flowcontrol receive desired
spanning-tree portfast
spanning-tree bpduguard enable
Port-channel21 is up, line protocol is up (connected)
Hardware is EtherChannel, address is
Description: ESX1 ISCSI SAN
MTU 9198 bytes, BW 2000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 17/255, rxload 16/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, link type is auto, media type is
input flow-control is off, output flow-control is unsupported
Members in this channel: Gi1/0/25 Gi1/0/34
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:07:12, output never, output hang never
Last clearing of "show interface" counters 1d21h
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 128760000 bits/sec, 8233 packets/sec
5 minute output rate 137021000 bits/sec, 7343 packets/sec
     520088013 packets input, 1454135312 bytes, 0 no buffer
     Received 1088 broadcasts (0 multicasts)
     0 runts, 0 giants, 0 throttles
     1534 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     0 input packets with dribble condition detected
     564793180 packets output, 978716517 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 pause output
     0 output buffer failures, 0 output buffers swapped out

Hi and Sorry Just copied and past the part that I thought was the problem. It seems that MTU size on switch two in the stack still has MTU 1500......
So here is the lot....
This interface is OK
sh controllers ethernet-controller g1/0/25
Transmit                  GigabitEthernet1/0/25                 Receive
2373084674113 Total bytes               2700589618458 Total bytes
   1259517537 Unicast frames               1355829627 Unicast frames
2373055994149 Unicast bytes             2700589410330 Unicast bytes
       314726 Multicast frames                      0 Multicast frames
     25604588 Multicast bytes                       0 Multicast bytes
        44657 Broadcast frames                   3252 Broadcast frames
      3075376 Broadcast bytes                  208128 Broadcast bytes
            0 System FCS error frames               0 IpgViolation frames
            0 MacUnderrun frames                    0 MacOverrun frames
            0 Pause frames                          0 Pause frames
            0 Cos 0 Pause frames                    0 Cos 0 Pause frames
            0 Cos 1 Pause frames                    0 Cos 1 Pause frames
            0 Cos 2 Pause frames                    0 Cos 2 Pause frames
            0 Cos 3 Pause frames                    0 Cos 3 Pause frames
            0 Cos 4 Pause frames                    0 Cos 4 Pause frames
            0 Cos 5 Pause frames                    0 Cos 5 Pause frames
            0 Cos 6 Pause frames                    0 Cos 6 Pause frames
            0 Cos 7 Pause frames                    0 Cos 7 Pause frames
            0 Oam frames                            0 OamProcessed frames
            0 Oam frames                            0 OamDropped frames
       423237 Minimum size frames               78563 Minimum size frames
    593742624 65 to 127 byte frames         338414660 65 to 127 byte frames
      1416083 128 to 255 byte frames          4836098 128 to 255 byte frames
       558097 256 to 511 byte frames          1505992 256 to 511 byte frames
      5464138 512 to 1023 byte frames         6457219 512 to 1023 byte frames
    472854085 1024 to 1518 byte frames      834470341 1024 to 1518 byte frames
        80781 1519 to 2047 byte frames         257961 1519 to 2047 byte frames
      2891352 2048 to 4095 byte frames       13701476 2048 to 4095 byte frames
     14353508 4096 to 8191 byte frames        8698824 4096 to 8191 byte frames
    168093015 8192 to 16383 byte frames     147411745 8192 to 16383 byte frames
            0 16384 to 32767 byte frame             0 16384 to 32767 byte frame
            0 > 32768 byte frames                   0 > 32768 byte frames
            0 Late collision frames                 0 SymbolErr frames
            0 Excess Defer frames                   0 Collision fragments
            0 Good (1 coll) frames                  0 ValidUnderSize frames
            0 Good (>1 coll) frames                 0 InvalidOverSize frames
            0 Deferred frames                       0 ValidOverSize frames
            0 Gold frames dropped                   0 FcsErr frames
            0 Gold frames truncated
            0 Gold frames successful
            0 1 collision frames
            0 2 collision frames
            0 3 collision frames
            0 4 collision frames
            0 5 collision frames
            0 6 collision frames
            0 7 collision frames
            0 8 collision frames
            0 9 collision frames
            0 10 collision frames
            0 11 collision frames
            0 12 collision frames
            0 13 collision frames
            0 14 collision frames
            0 15 collision frames
            0 Excess collision frames
LAST UPDATE 4870 msecs AGO
This interface have problem. It is in portchannel with g1/0/25. Ive got more interfaces and port-channels showing the same behavior for switch two in my cluster.
sh controllers ethernet-controller g2/0/25
Transmit                  GigabitEthernet2/0/25                 Receive
925460044357 Total bytes                201085804055 Total bytes
    702370104 Unicast frames                184041790 Unicast frames
925449913241 Unicast bytes              201085599895 Unicast bytes
       118823 Multicast frames                      0 Multicast frames
      9171804 Multicast bytes                       0 Multicast bytes
        14251 Broadcast frames                   3190 Broadcast frames
       959312 Broadcast bytes                  204160 Broadcast bytes
            0 System FCS error frames               0 IpgViolation frames
            0 MacUnderrun frames                    0 MacOverrun frames
            0 Pause frames                          0 Pause frames
            0 Cos 0 Pause frames                    0 Cos 0 Pause frames
            0 Cos 1 Pause frames                    0 Cos 1 Pause frames
            0 Cos 2 Pause frames                    0 Cos 2 Pause frames
            0 Cos 3 Pause frames                    0 Cos 3 Pause frames
            0 Cos 4 Pause frames                    0 Cos 4 Pause frames
            0 Cos 5 Pause frames                    0 Cos 5 Pause frames
            0 Cos 6 Pause frames                    0 Cos 6 Pause frames
            0 Cos 7 Pause frames                    0 Cos 7 Pause frames
            0 Oam frames                            0 OamProcessed frames
            0 Oam frames                            0 OamDropped frames
       155980 Minimum size frames                3226 Minimum size frames
     92357460 65 to 127 byte frames          52503630 65 to 127 byte frames
       542363 128 to 255 byte frames           660137 128 to 255 byte frames
      1843346 256 to 511 byte frames           500600 256 to 511 byte frames
      6158096 512 to 1023 byte frames         1116353 512 to 1023 byte frames
    601445933 1024 to 1518 byte frames      129261034 1024 to 1518 byte frames
            0 1519 to 2047 byte frames         319527 1519 to 2047 byte frames
            0 2048 to 4095 byte frames              0 2048 to 4095 byte frames
            0 4096 to 8191 byte frames              0 4096 to 8191 byte frames
            0 8192 to 16383 byte frames             0 8192 to 16383 byte frames
            0 16384 to 32767 byte frame             0 16384 to 32767 byte frame
            0 > 32768 byte frames                   0 > 32768 byte frames
            0 Late collision frames                 0 SymbolErr frames
            0 Excess Defer frames                   0 Collision fragments
            0 Good (1 coll) frames                  0 ValidUnderSize frames
            0 Good (>1 coll) frames            319524 InvalidOverSize frames
            0 Deferred frames                       3 ValidOverSize frames
            0 Gold frames dropped                   0 FcsErr frames
            0 Gold frames truncated
            0 Gold frames successful
            0 1 collision frames
            0 2 collision frames
            0 3 collision frames
            0 4 collision frames
            0 5 collision frames
            0 6 collision frames
            0 7 collision frames
            0 8 collision frames
            0 9 collision frames
            0 10 collision frames
            0 11 collision frames
            0 12 collision frames
            0 13 collision frames
            0 14 collision frames
            0 15 collision frames
            0 Excess collision frames

Similar Messages

Cisco Catalyst 3850 Series

Can I use DC power supply for
Cisco Catalyst 3850 Series?

Unfortunately your post is off topic here, in the TechNet Site Feedback forum, because it is not Feedback about the TechNet Website or Subscription. This is only one forum among the many
that are on the TechNet Discussion Forums, and given your post, you likely chose the wrong forum. This is a standard response I’ve written up in advance to help many people (thousands, really.) who post their question in this forum in error, but please
don’t ignore it. The links I share below I’ve collected to help you get right where you need to go with your issue.
For technical issues with Microsoft products that you would run into as an
end user of those products, one great source of info and help is
http://answers.microsoft.com, which has sections for Windows, Hotmail, Office, IE, and other products. Office related forums are also here:
http://office.microsoft.com/en-us/support/contact-us-FX103894077.aspx
For Technical issues with Microsoft products that you might have as an
IT professional (like technical installation issues, or other IT issues), you should head to the TechNet Discussion forums at
http://social.technet.microsoft.com/forums/en-us, and search for your product name.
For issues with products you might have as a Developer (like how to talk to APIs, what version of software do what, or other developer issues), you should head to the MSDN discussion forums at
http://social.msdn.microsoft.com/forums/en-us, and search for your product or issue.
If you’re asking a question particularly about one of the Microsoft Dynamics products, a great place to start is here:
http://community.dynamics.com/
If you really think your issue is related to the subscription or the TechNet Website, and I screwed up, I apologize! Please repost your question to the discussion forum and include much more
detail about your problem, that could include screenshots of the issue (do not include subscription information or product keys in your screenshots!), and/or links to the problem you’re seeing.
If you really had no idea where to post this question but you still posted it here, you still shouldn’t have because we have a forum just for you! It’s called the Where is the forum for…?
forum and it’s here: http://social.msdn.microsoft.com/forums/en-us/whatforum/
Moving to off topic.
Thanks
MSDN and TechNet Subscriptions Support
Did Microsoft call you out of the blue about your computer?
No, they didn't.

Cisco Catalyst 3850 as ntp master

Hi All,
I have 2 x Cisco Catalyst 3850 stacked together. What are your recommendations if I use the C3850 as a ntp master for all edge switches connected in my network? All edge switches must be authenticated if it needs NTP sychronization. But other than that, what are the downsides?
For example,
1. I heard that switches do not have an internal clock so is a poor device to be a centralized NTP master.
2. I have also read that switches also have slow CPU processors that may lack the processing required.
3. Its NTP sychronization will use external NTP servers which are resolved into IP addresses (e.g. pool.ntp.org). IP address can change. What other more reliable NTP sources are there?
4. Any other thoughts and comments are most welcome.

Firstly, DO NOT use the command "ntp master". Cisco do not recommend using this commands because this will confuse the NTP propagation inside the network.
Next, all Cisco devices do not have a dedicated clock. All appliances need to get SNTP/NTP time synch from somewhere. This "somewhere" could either be a dedicated GPS-based NTP server and/or a time synch somewhere out in the internet.
You can also use the command "ntp update-calendar". This new command allows appliances to take regular "snapshot" of the time and save it into the NVRAM. In case there was a reboot or a power failure, the appliance's time is not too far away instead of waiting 5 to 10 minutes for SNTP/NTP to synch.

How many Cisco Catalyst 3850 switches can make up a Cisco StackPower stack?

I know the number of Cisco 3850 switches for stacking is 9, so, if I make up a Cisco StackPower stack, MAX is 9, too?

Hi, emma, only 4 switches can become part of the same Cisco StackPower stack in a ring topology.
For the Cisco 3850 switches stack number,there are two types:
Up to 9 Cisco Catalyst 3850 switches can be stacked together to build single logical StackWise-480 switch since Cisco IOS XE Release 3.3.0SE. Prior to Cisco IOS XE Release3.3.0SE, up to 4 Cisco Catalyst 3850 switches could be stacked together.

Cisco Catalyst 3850 switches

How many Cisco Catalyst 3850 switches can stack into a single logical entity?

Hi, emma, only 4 switches can become part of the same Cisco StackPower stack in a ring topology.
For the Cisco 3850 switches stack number,there are two types:
Up to 9 Cisco Catalyst 3850 switches can be stacked together to build single logical StackWise-480 switch since Cisco IOS XE Release 3.3.0SE. Prior to Cisco IOS XE Release3.3.0SE, up to 4 Cisco Catalyst 3850 switches could be stacked together.

Cisco catalyst 3850 switch won't take command: "switchport mode trunk encapsulation dot 1q"

Hi all,
I'am working on this switch's configuration. when I typed "switchport mode trunk encapsulation dot 1q", I got an error " invavid input". I'm guessing that this model already set encapsulation type to dot 1q, and that's why the switch won't take it, right?
Please help!

According to the documents it supports both.
You are however using the wrong command, it should be -
"switchport trunk encapsulation dot1q"
ie. no "mode" keyword.
If it doesn't take that then do a "sh int <x> capabilities" and it should show you which encapsulation methods are supported.
Jon

Catalyst 3850 vs Nexus 3K

Hi ,
I have a question. If the only requirement for the DC is to have iSCSI for some servers , is it better to go for Nexus 3K or I should choose Cat 3850. Apparently with 10 gig uplinks Cat 3850 is more expensive. Can someone plz tell what would be the benefits of each in this scenario?
Fawad

Hi ,
Cat 3850 is mainly used for unify wired and wireless networks. Cisco Catalyst 3850 Switches, which combine wired and wireless by supporting wireless tunnel termination and full wireless LAN controller functionality.
In other hand , Nexus 3000 is datacenter top of the rack switch and low latency , unify data ad storage switch and well suited for your Iscsi requirement . so i would suggest nexus 3000 .
HTH
Regards,
VS.Suresh.
*Plz rate the usefull posts *

Catalyst 3850 rack mount kit: 3850-RACK-KIT or C3850-4PT-KIT ?

When purchasing a Cisco Catalyst 3850, do we need to buy the rack mounting kit to install it in a standard 19" rack? 3850-RACK-KIT or C3850-4PT-KIT ? Is the 4-point kit really necessary, can the 3850 hang only on the front of the rack?

No, you don't need the C3850-4PT-KIT. 3850-RACK-KIT comes in the box and it is good enough as long as you rack it nice and tide. The reason some people use C3850-4PT-KIT is because the switch will hang from the back a little when using 3850-RACK-KIT and so if you don't like that than you want the 4PT.
HTH

Catalyst 3850 Cross-Stack EtherChannel

On 3850 configuration guide, I came across PAgP desirable mode is not supported in the switch stack (cross-stack EtherChannel).
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3850/software/release/3se/layer2/configuration_guide/b_lay2_3se_3850_cg/b_lay2_3se_3850_cg_chapter_0101.html
But on Q&A document, it mentioned 3850 supports PAgP.
Q. What cross-stack EtherChannel link bundling protocols are supported?
A. The Cisco Catalyst 3850 supports Cisco Port Aggregation Protocol (PAgP) and industry-standard IEEE 802.3ad Link Aggregation Control Protocol (LACP). Other 3750 Series Switches support only LACP for cross-stack EtherChannel.
Seems like both statements are contradicting.
Can someone shed some light on this?
Thank you.

Hi, adimakmur
Cisco Catalyst 3850 Cross-Stack EtherChannel can be PAgP+ and can be used for VSS dual active detection.
In last deployment of 3850 we use Cross-Stack EtherChannel and use it as trusted for VSS dual active detection.
c6500-V#sh switch virtual dual-active pagp
PAgP dual-active detection enabled: Yes
PAgP dual-active version: 1.1
----skiped----
Channel group 106 dual-active detect capability w/nbrs
Dual-Active trusted group: Yes
Dual-Active Partner Partner Partner
Port Detect Capable Name Port Version
Te1/7/7 Yes c3850-307 Te1/1/3 1.1
Te2/7/7 Yes c3850-307 Te2/1/3 1.1
---skiped----
c6500-V#sh etherchannel 106 protocol
Protocol: PAgP
c3850-307#sh etherchannel port-channel
Channel-group listing:
Group: 1
Port-channels in the group:
Port-channel: Po1
Age of the Port-channel = 235d:20h:50m:10s
Logical slot/port = 12/1 Number of ports = 2
GC = 0x00010001 HotStandBy port = null
Port state = Port-channel Ag-Inuse
Protocol = PAgP
Port security = Disabled
Ports in the Port-channel:
Index Load Port EC state No of bits
------+------+------+------------------+-----------
0 00 Te1/1/3 Desirable-Sl 0
0 00 Te2/1/3 Desirable-Sl 0
Time since last port bundled: 169d:04h:58m:49s Te1/1/3
Time since last port Un-bundled: 169d:05h:00m:47s Te1/1/3

Catalyst 3850 indirecttly connected ap

Does the Cisco Catalyst 3850 with version 3.06.01 support indirectly connected access points?
Wich does version the switch need to support this feature?
Thanks...

Duplicate post.
Go HERE.

Error in switch ports POE model, "Cisco Catalyst 2960S-24PS-L Switch"

I have problem with the poe switch Cisco Catalyst 2960S-24PS-L posts does not respond, and me the following error resporta was t
%PLATFORM_ENV-3-ILP_PORT_POST_ERR: %s can’t be brought up because it failed POST
in Inline Power test.
he source of that error and what are the possible causes

Hey Dustin,
Device needs to be RMA'ed. The inline power supply has failed.
HTH.
Regards,
RS.

Cisco Catalyst WS-C3560-48TS and DLINK 3120 interface errors

Hello,
We are getting a lot of FCS-Err in one FC- GIgabit trunking interface between Cisco Catalyst WS-C3560-48TS running IOS Version 12.2(25)SEE3 and DLINK 3120 Firmware 4.00.015.
Our config in the cisco is the following:
interface GigabitEthernet0/1
description SWITCH-Dlink01
switchport trunk encapsulation dot1q
switchport mode trunk
macro description cisco-switch
spanning-tree link-type point-to-point
We have tried without "macro description cisco-switch" and "spanning-tree link-type point-to-point" too and the problem persist.
If we run "sh interfaces counters errors"
Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize
Gi0/1 0 11423 0 11423 12516029
The errors counters in the DLINK are growing very fast too.
Usually these errors are related with hardware or cable problems, we have changed the cable, the SFP and the port, but the problem is still there.
We have activated the debug for the interface and syslog, but we aren't getting any error.
Do you have any idea about this issue or how to troubleshoot it?

Hi,
Try to hard set the ports on both sides to Gig/full duplex and test again.
HTH

CRC errors and input errors on Te 1/2 of Cisco WS-C3560X-48 switch

Hi All,
I am observing CRC errors and input errors on one of the Te1/2 interface of WS-C3560X-48 Cisco switch. I have not observed any CRC errors or input errors on the connected interface at other end. Can you please let us know whether the issue is with cable or SFP module.
Effected interface:
TenGigabitEthernet1/2 is up, line protocol is up (connected)
Hardware is Ten Gigabit Ethernet, address is f866.f243.e6b6 (bia f866.f243.e6b6)
Description: *** MAN-SW1B***
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 254/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, 10Gb/s, link type is auto, media type is SFP-10GBase-SR
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 3w5d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 29000 bits/sec, 30 packets/sec
5 minute output rate 45000 bits/sec, 37 packets/sec
68905128 packets input, 8272036576 bytes, 0 no buffer
Received 68904979 broadcasts (68812046 multicasts)
0 runts, 0 giants, 0 throttles
146170 input errors, 130065 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 68812046 multicast, 0 pause input
0 input packets with dribble condition detected
83524620 packets output, 12642123488 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
Other end.
TenGigabitEthernet1/4 is up, line protocol is up (connected)
Hardware is Ten Gigabit Ethernet Port, address is 503d.e53b.9703 (bia 503d.e53 b.9703)
Description: *** DMZ-SW1B ***
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 10Gb/s, link type is auto, media type is 10GBase-SR
input flow-control is on, output flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 32000 bits/sec, 27 packets/sec
5 minute output rate 21000 bits/sec, 22 packets/sec
918379921 packets input, 312586470396 bytes, 0 no buffer
Received 881142868 broadcasts (875016400 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
463132111 packets output, 240865283601 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out

When there are more than two members in a cluster (stack), the Gigabit interface operates at half-duplex. Since collisions can result at half-duplex, some CRCs errors are normal.

Cisco IP phone problem with external directory http error

Hi,
I have a problem when I try to open the directory on different model Cisco IP Phone for new deployment.
In CUCM (version 8.5) we have configured internal and external directory and on each device set the "service provisioning" to "both". For all the sites configured in CUCM this feature is working properly, but not in the new deployed site. I´ve already verified the url is written properly.
I get the following error messages for these different models:
- Cisco IP phone 8945: "HTTP connection failed"
- Cisco IP Comm: "HTTP error [500] "
Thank you for your help,
Regards,
David Lozano

Hi David,
What firmware are you using? Do you have 8945s on the other sites? I found a bug, but I'm not sure it applies to your description:
CSCty58000 Bug Details
8945 freezes when directories is pressed
Symptom:
8945 freezes when directories button is pressed.
Conditions:
This issue happens when the phone load is 9.2.3 and the directories URL doesn't contain port number.
Workaround:
Please use http://X.X.X.X:8080/ccmip/xmldirectory.jsp for the directories
URL instead of http://X.X.X.X/ccmip/xmldirectory.jsp
You can try upgrading to firmware 9.3(1)
Regards,
Tere.

How to Clear the Input errors in a Cisco ASA Interface?

Hi Everyone,
                  My Expertise with Cisco ASA is Very less. I have observed Input errors in a Couple of Interfaces in Cisco ASA 5540 Firewall.
296867 input errors, 0 CRC, 0 frame, 296867 overrun, 0 ignored, 0 abort
0 pause input, 0 resume input
0 L2 decode drops
102091138038 packets output, 96596756282996 bytes, 2683 underruns
0 pause output, 0 resume output
0 output errors, 0 collisions, 2 interface resets
0 late collisions, 0 deferred
52 input reset drops, 0 output reset drops, 0 tx hangs
input queue (blocks free curr/low): hardware (255/230)
output queue (blocks free curr/low): hardware (255/0)
I need to Clear the Input errors on this particular Interface.
Will Clear interface GigabitEthernet 0/0 will help?
Thanks in Advance,
Nanda

Hi,
Here is an example of using the command on my own ASA5505 firewall
interface Ethernet0/0
description WAN Access
switchport access vlan 10
ASA# sh interface Ethernet 0/0
Interface Ethernet0/0 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps, DLY 100 usec
        Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
        Input flow control is unsupported, output flow control is unsupported
        Description: WAN Access
        Available but not configured via nameif
        MAC address 0025.45f4.0a9a, MTU not set
        IP address unassigned
        9679 packets input, 6532697 bytes, 0 no buffer
        Received 2 broadcasts, 0 runts, 0 giants
        0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
        0 pause input, 0 resume input
        0 L2 decode drops
        0 switch ingress policy drops
        8421 packets output, 2202683 bytes, 0 underruns
        0 pause output, 0 resume output
        0 output errors, 0 collisions, 0 interface resets
        0 late collisions, 0 deferred
        0 rate limit drops
        0 switch egress policy drops
        0 input reset drops, 0 output reset drops
ASA# clear interface Ethernet0/0
ASA# sh interface Ethernet 0/0
Interface Ethernet0/0 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps, DLY 100 usec
        Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
        Input flow control is unsupported, output flow control is unsupported
        Description: WAN Access
        Available but not configured via nameif
        MAC address 0025.45f4.0a9a, MTU not set
        IP address unassigned
        0 packets input, 0 bytes, 0 no buffer
        Received 0 broadcasts, 0 runts, 0 giants
        0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
        0 pause input, 0 resume input
        0 L2 decode drops
        0 switch ingress policy drops
        0 packets output, 0 bytes, 0 underruns
        0 pause output, 0 resume output
        0 output errors, 0 collisions, 0 interface resets
        0 late collisions, 0 deferred
        0 rate limit drops
        0 switch egress policy drops
        0 input reset drops, 0 output reset drops
interface Ethernet0/0
description WAN Access
switchport access vlan 10
- Jouni

Problem Cisco Catalyst 3850 input errors

Similar Messages

Maybe you are looking for