Problem with K8T Neo and cdrom

Hi!
I have got a problem with my cdburner (LG). When i put in a new hdd in my computer the cd stoped workin. I have a seagate 200gig sata and with that it worked fine. And when i put in a WD 250gig sata disk to the computer the cd burner stoped working. But both the discs works fine. So What could help? The PSU should be enough. It´s a qtecnology 400w (NOT a Qtec). And i have used it on a more powerdemanding system.

Make sure that the Opticals and the HDD's do not share an ISE Channel. Typically both HDD would be on IDE0 and any Opticals would thenm be on IDE1. Also check that your jumpers for Master/Slave/Cable Select are set correctly for all drives. As you just added a driver you may have to remove the opticals drivers and reinstall them so that any positional changes are compensated for properly in your registry.

Similar Messages

Probs with k8t neo and radeon 9500 non pro

Hi!
I´m totaly new with amd and i got a msi k8t neo and a sempron 2800+ with 1gb memory and a saphire radeon 9500 non pro and the computer does not start with that graphiccard.The processor fan just spins up a bit then it dies. But with a gforce 5200 card the computer works fine. I have tryed the saphire card in my server with a P4 1,6ghz and on that motherboard it works just fine.
Im from sweden so my english is not the best ;-)

Quote from: qTj on 17-November-05, 20:25:05
Yes i have tryed all those things. But my card works perfectly in 2 diffrent computers. So i dont think that the vidccard is broken.. But what do i know...
Well you know that othergfx cards do work oin ur board, so I still say you RMA it, or swap if with another card that will work
Quote
"drulleförsäkringen"
translates like "fools insurance", apperently in Sweden U get a refund when u buy something and wreck it

Problems with K8T Neo-FSR (ms-6702) and radeon 9800

hey
does anybody have problems or success using an ati radeon 9800 graphics card with this board?
any special configurations required ?
seems that other msi neo boards cause problems with this card

Make sure to use the VIA drivers that came with the board as the newer Hyperions do not work as well and have been known to cause issues.

Early Chipset Initialization problem with K8T Neo 2 - FIS2R

This one has me stumped.
I went to install a new CPU fan earlier today and while I was installing the fan I had to remove my sound card and AGP card so I could screw the fan to the side of the heat sink.
I got all that done and went to start the computer back up and now I get a contineous high pitched sound while at the same time 3 beeps. The D bracket shows a green LED on 1 so this is the "early chipset initialization" problem.
What is causing this and why would this happen after a fan installation?
Specs
A64 3200+ Winchester
1.5 GB RAM (2x 512, 2x 256) DDR 400
MSI K8T Neo 2 - FIS2R
PNY GF 6800
Audigy 2 ZS Gamer
200GB IDE HDD
80 GB IDE HDD
DVD - R/RW
Win XP Pro w/ SP2

Okay after a bit of messing around with the problem I discovered what the problem was....
I didn't plug in the power to the video card
Yeah the 6800 uses needs more power from the PSU and I left that little rail unplugged. Maybe some other soul will find this useful in a time of need.

Help! XP install problems with K8T Neo-FIS2R

The other day I put together a new system for a friend. I got the system to POST properly, the diagnostic lights on the D bracket are fine, and I can edit the BIOS, and the BIOS sees all the drives properly.
However, installing XP Pro has been impossible. I set the system to boot first to the CD, then to the hard drive (from the BIOS). After booting to the CD, I never see the message I am used to seeing ("Press any key to boot from CD...) when booting from the XP Pro install disk. The system thinks about things for a long time with a blank screen, then later it finally begins to do the install. Things appear normal at this point as in any other time I have installed XP Pro. I reformat the hard drive to start clean and then the XP install files are copied over. I get the standard message that the system will reboot and this is where things get flaky. The system reboots, but I never get the message once again on whether or not to boot from the CD. So after a while the system tries to install XP once again (it would repeat this process forever....trust me). I've popped the CD out right after the system reboots so it will try to go to the hard drive. I just get some kind of boot failure message and to insert the bootable media or whatever. I've even gone into the BIOS right after the reboot to switch the BIOS loading to try and load the hard drive first. This still doesn't give me the desired results.
This is by far the weirdest thing I've ever experienced when doing an install. I've installed XP Pro on at least 15-20 desktops/laptops of different configs and never ran into this before.
The BIOS settings are stock. I didn't see anything in there that was really needed tweaking or that hadn't "set itself". I haven't messed with the SATA or RAID stuff since it's not really necessary in this situation.
Here are the system specs:
--Antec 430 True Power PSU
--K8T Neo-FIS2R mobo
--AMD 3000+ 64 bit CPU
--40GB Maxtor HD (master on IDE1)
--Lite-On DVD-ROM drive (slave on IDE1)
--80GB Western Digital (8MB buffer) (master on IDE2)
--Sony DRU510A DVD-RW (slave on IDE2)
--(2) Kingmax 184 Pin 512MB DDR PC-3200 Model# MPXC22D-38
--ATI 9800 Pro
--3.5 Floppy
All the components except the mobo, CPU, and memory are from another AMD system that was running fine. No problems with any of the HD's or the optical drives. All new components were purchased from newegg.
I thought that maybe I had a problem with the jumpering of the drives so I messed with those in about every possible combination. I took IDE2 completely out of the system and just tried to get it running with the 40GB Maxtor and the Lite-On drive. I tried about every master/slave/cable select combination but nothing was working. In certain combinations the BIOS recognized everything as I intended. I've pulled everything off that doesn't need to be connected. Keyboard, monitor, and internal components are the only things connected.
I don't consider myself to be a guru at this business, but I can get through most things with enough trial and error. This really has me stumped.
Any help is certainly appreciated.
Thanks,
Heath

Quote
Originally posted by chasmon
Hi all,
I have just setup up a brand new system but am having probelms getting it working. I want to install XP on a single Maxtor 160Gb drive.
I have my HD on Promise Ser1 and all SATA stuff in BIOS enabled. When I get to the screen I press F6 and then when promted I insert the floppy with the promise drivers on. I then get this message:
"File txtsetup.oem caused an unexpected error (4096) at line 1742 in d:\xpclient\base\boot\setup\oemdisk.c"
I can't get past this screen I have tried:
1.Drivers from the CD supplied.
2.Drivers from the MSI website.
Please help me this lot cost lots of hard earned I'm pretty gutted at the moment.
System:
Antec 380W PSU and Sonata Case
LG DVDROM 8163B
NEC DVDR/RW 2500B
Panasonic Floppy
Neo FIS2R mobo
Maxtor Diamondmax Plus 9 160Gb SATA150
Benq RF K/B & Mouse
Download the drivers from MSI again, and when you copy the contents of the XP folder to floppy ADD the file txtsetup.oem from the directory above that folder. Worked for me..!
Ian

Registry/boot problem with K8T Neo mobo (solved)

I got similar problem: https://forum-en.msi.com/index.php?threadid=40752&sid=
Though my error message is: "Windows could not start because the following file is missing or corrupt:\WINNT\SYSTEM32\CONFIG\SYSTEM"
I did NOT have this problem before i enabled the Realtek gigabit ethernet controller in BIOS.. But now when it is enabled everything runs/installs/reboots fine... until i shut down and when i turn power on next day i get that error message.
So: when Realtek 8169/8110 gigabit ethernet NIC is enabled in BIOS, necessary drivers installed and system shut down, registry get corrupted while shutting down.
I had AMI BIOS 1.1 when got this first time (after enabling realtek), flashing to 1.2 didn't help.
I also tried newest realtek 8169/8110 drivers (5.611.1231.2003) instead of original (5.606.811.2003)(they're still in msi neo-fis2r page i see) but it didn't help either.
So, any suggestions? i believe the integrated realtek causes the problem because it didn't occur before i enabled it from bios->integrated stuff... or is there any other possible reason?
oh, msinfo32 says that radeon 9800XT, IEEE1394 controller (firewire in audigy2) and realtek controller share the same IRQ 16.. i removed firewire controller but it didn't help.. could radeon and realtek sharing the same IRQ be the problem?

Didn't try the external yet, i'll still try something with this.
:: Do you have a home network setup, or connect straight to modem?
straight to modem.
i doubt it is the audigy, it worked before... and i've disabled everything i don't need like onboard audio, onboard 1394.. (never installed 'em)
i noticed one thing: all people with similar problems are running win2000 SP4, you run XP so it's ok.
MS knowledge base says "If one or two registry hives consistently become corrupted for no reason, the problem probably occurs at shutdown and is not discovered until you try to load the registry hive at the next restart. In this scenario, the registry hive is written to disk when you shut down the computer, and this process may stop the computer or a component in the computer before the writing is completed." http://support.microsoft.com/default.aspx?scid=kb;en-us;822705
so something (realtek?) is writing to the registry while i shut down the pc.
i'm gonna disable realtek before shutdown & see if it boots without errors... if it does, i'll just have to disable it *always* before shutdown.... sounds like driver error for me?

Problems with P965 Neo and E4500 Core 2 Duo

Hope someone can help.
I have a gadget for Vista that shows core usage. The second core does not register at all when running a performance test. Also, when I look under "My Computer" at the Properties it shows:
Processor: Intel(R) Core(TM)2 Duo CPU E4500 @ 2.20GHz 1.10GHz
Also, my Windows Experience Index for my processor is only 4.3, seems low for the processor.
Makes me wonder if the second core is toast? Why would it show 1.10GHz? Looking at my BIOS version, I believe it's at 1.5 (I've never updated it since it came out of the package) but the Live Update Online utility says there are no newer versions available. I tried to download the BIOS update off MSI's website, but when I click on the .exe file, it flashes and then goes away. So fast, that I can't even read or see much of anything. The instructions that were included do not cover Vista, and say I have to get a 98/XP boot disk??? When has that ever been necessary for a BIOS update?
Anyway, any help would be appreciated.

Hello and Welcome to the Forum!
BIOS-Updates
BIOS Updates should be done in pure DOS mode. Flashing from a Windows Environment is very risky and should be avoided if possible. Flash your BIOS only if you are aware of the risks of BIOS Flashing. Updating the BIOS should be the last resort in troubleshooting. If you are sure you want to flash a different BIOS use the Forum's USB-Flashing. It is easy to use and prepares the Flash Drive automatically for a DOS-Flash. You can find it here:
https://forum-en.msi.com/index.php?topic=108079.0
Quote
The second core does not register at all
Is your CPU properly recognized in BIOS and during POST?
In BIOS, make sure the following options are properly set:
ACPI = Enabled
(IO)APIC = Enabled
MPS Table Version = 1.4
If you are sure these options are as shown above, force Vista to re-detect proper HAL during startup. You have to find Vista's Advanced Boot Options dialog box in order to do that:

Problem with repaired neo fis2r

I am experiencing performance problems with my neo tha t I am not sure where to begin trouble shooting. I had an video card falure(delaminated pin on agp ) which resulted in damage to the agp slot I rma 'd my neo and it returned marked repaired with a grey agp slot , bios 1.4 ( had 1.6 installed) and the same serial #. I reinstalled all components. noted the retrograde bios and flashed to 1.8. then I attempted to return all settings to theyre original state only to find that I can't overclock! previously I got 250mhz clock with perf mode set to ultra turbo and ram set to 333mhz . now I can't get past perf mode fast and 205mhz no matter what. I see references to bios 1.8 as being not very overclockable.this may be the problem but the waters have been muddied by the multitude of events. I am not an expert and do not know where to start. I was so thrilled with the performance of my neo and now I am at a loss . Is the bios responsible for this abysmal performance or is my system still compromised? I don't know what to do to determine its state. my system is as follows:-
neo fis2r( of course)
2.4c p4 with zalman alcu 7000
ati 8500dv
512mb samsung 400mhz ram
seagate barracuda sata 150 raid 0
pci modem card
thermaltake xaser2 case
any suggestions would be greatly appreciated
kev

essentially I am not just concerned about it's current inability to overclock. but more in the fact that b4 the repiar of the board I was able to overclock with no difficulty and no special considerations. in fact when I look at my little log of bios settings the agp clock was set at 66.6/33.3 after all the overclocking. and now with EXACTLY the same components( ati card repalced but physically identical) none of those same settings work. did the failure damage other components whose failure is not yet critical path or has the bios upgrade caused instability?

Problem with PT8 NEO Y VGA ATI SAPHIRE 9250SE

problem with PT8 NEO Y VGA ATI SAPHIRE 9250SE

From the VGA test report: http://www.msi.com.tw/html/products/mainboard/testreport_pdf/6799/vga.pdf for the board , i can't find ATI Radeon 9250SE , but it is obvious that MSI only tested their Nvidia cards and no ATI cards. So, you'd better to try Nvidia cards or contact your VGA vendor to ask if there is the latest VGA BIOS to solve your issue.
Anyway, remember to tell us the results .

MOVED: [Opteron] Problem with K8T Master2

This topic has been moved to Server/workstation.
[Opteron] Problem with K8T Master2

No, there is no confusion.. I do know the difference between MS-9130 and the MS-9617. Almost identical except the chipset. Reason I was looking for it is because I used to have it on a board a couple years ago that I eventually sold. I recently picked up 5 more and I have a few 275's. One of my boards is running a custom bios with a pair of 275's, but I wanted to check the difference between the 2 versions.

Boot problems with K8N Neo FSR

Recently i bought a new MSI K8N Neo FSR mainboard and an Athlon64 3000+
I noticed that a lot of people on this board had problems when booting Windows XP
I had the same problem: Every time i tried to boot Win, it freezed at the Win XP logo.
It seems that the problem is my cordless logitech keyboard.
When i'm using a standard PS/2 keyboard i have no problems booting.
Are there any known problems with nForce3 based mainboards and cordless logitech keyboards?
Does anyone know if there is a way to fix this problem?

There just seems a problem with some mobos and keyboards.
Usually it's a PS2 thing, but looks like you have found another to add to the list.
Note...
COMPATIBLE INPUT DEVICES (Keyboards)
Aspire/Mitsuko Internet Keyboard
Cherry Soft Touch
Chicony #KB-9805
Compaq EVO Series
CoolerMaster Q
Dell
Logitech Cordless Duo, Logitech Ultra-X, Logitech Internet Navigator
Logitech Di Novo Series
Memorex Multimedia
Microsoft Multimedia Wireless, Microsoft Desktop Elite
Mitsumi #KFKEB9HY
Qtronix Scorpius
Viewmate Office

Problems with ListViews Drag and Drop

I'm surprised that there isn't an Active X control that can do this more
easily? Would
be curious to find out if there is - although we aren't really embracing the
use of
them within Forte because it locks you into the Microsoft arena.
---------------------- Forwarded by Peggy Lynn Adrian/AM/LLY on 02/03/98 01:33
PM ---------------------------
"Stokesbary, Michael" <[email protected]> on 02/03/98 12:19:52 PM
Please respond to "Stokesbary, Michael" <[email protected]>
To: "'[email protected]'" <[email protected]>
cc:
Subject: Problems with ListViews Drag and Drop
I am just curious as to other people's experiences with the ListView
widget when elements in it are set to be draggable. In particular, I am
currently trying to design an interface that looks a lot like Windows
Explorer where a TreeView resides on the left side of the window and a
ListView resides on the right side. Upon double clicking on the
ListView, if the current node that was clicked on was a folder, then the
TreeView expands this folder and the contents are then displayed in the
ListView, otherwise, it was a file and it is brought up in Microsoft
Word. All this works great if I don't have the elements in the ListView
widget set to be draggable. If they are set to be draggable, then I am
finding that the DoubleClick event seems to get registered twice along
with the ObjectDrop event. This is not good because if I double click
and the current node is a folder, then it will expand this folder in the
TreeView, display the contents in the ListView, grab the node that is
now displayed where that node used to be displayed and run the events
for that as well. What this means, is that if this is a file, then Word
is just launched and no big deal. Unfortunately, if this happens to be
another directory, then the previous directory is dropped into this
current directory and a recursive copy gets performed, giving me one
heck of a deep directory tree for that folder.
Has anybody else seen this, or am I the only lucky one to experience.
If need be, I do have this exported in a .pex file if anybody needs to
look at it more closely.
Thanks in advance.
Michael Stokesbary
Software Engineer
GTE Government Systems Corporation
tel: (650) 966-2975
e-mail: [email protected]

here is the required code....
private static class TreeDragGestureListener implements DragGestureListener {
     public void dragGestureRecognized(DragGestureEvent dragGestureEvent) {
     // Can only drag leafs
     JTree tree = (JTree) dragGestureEvent.getComponent();
     TreePath path = tree.getSelectionPath();
     if (path == null) {
          // Nothing selected, nothing to drag
          System.out.println("Nothing selected - beep");
          tree.getToolkit().beep();
     } else {
          DefaultMutableTreeNode selection = (DefaultMutableTreeNode) path
               .getLastPathComponent();
          if (selection.isLeaf()) {
          TransferableTreeNode node = new TransferableTreeNode(
               selection);
          dragGestureEvent.startDrag(DragSource.DefaultCopyDrop,
               node, new MyDragSourceListener());
          } else {
          System.out.println("Not a leaf - beep");
          tree.getToolkit().beep();
}

Problems with Customer Service AND unexplained charges!

I've been with Verizon for I-don't-know-how-many years, and through the years you are bound to have a few problems here and there but some of the problems are just ridiculous! It's also the same reocurring problem!!!!!!!!!!!!!!!! I was with Alltel first, before it was bought out by Verizon. The years I was with Alltel, I didn't have near as many problems. It seems EVERY time I do the smallest change or something to my phone or bill, I get a ridiculous amount of charges that I was NOT aware of, nor told about... EVEN IF I ask "So this isn't going to change my bill, or there will not be any unexpected/unexplained charges that I don't know about?"... BUT not matter how many times I ask... and NO matter how many times I am told "no"... there always is. For example.... last year, I updated and signed a new 2 year contract and purchased the first Driod. Before, my 30 day warranty was up, I was having problems with my Driod, and decided to send it in and get a new one. Before I did this.. I called customer service to make sure there would be no interuption in my bill, and there wouldn't be any unexpect charges, and there would be no difference in anything. I was told there was not, and once I recieved my new phone, just send it in and nothing would be changed. Of course, when I get my bill.. I see I was charged $500 for the new phone. It was explained to me that my credit card was reimbursed (which I never check that card, because I never used it expect to purchase the phone) and that I was recharged for the new phone, since it was a new phone. So I had to fork out the $500 (on top of my bill) and then wait months to get the $100 rebate card. Months after that, I "assumed liablity of my line" because I was on a plan with my family. I decided to have my own line, so I "assumed liability." I was not told that when I did that, I "renewed" my contract date. So I just added 6 more months to my 2 year contract. Was NOT told about that! Then again...... I was recently having problems with my Driod (the screen went black and would not come back on.) I had to turn on an OLD motorola razor, so I would not be without a phone for two days while I was waiting on my phone to come in. As soon as my phone came in, I had my Droid turned back on. I recieved my bill recently, and my bill was $200 over what it normally should be.... so I called in... apparently, when I had my phone replaced, they dropped off my data package and when I recieved my replacement driod, they never put it back on. So I was being charged for alllll my data usage... again I was NOT told about this. I wasn't even aware that they had dropped off my data package, and when/where did they get the authority to do that??? These are just a FEW of the problems that I have had.................................
Does anyone have these reoccuring problems!?

I understand that my bill can be viewed online, and I do view it fairly regularly, so if there are any unexplained charges, I can call Verizon asap. The problem does not come from me not understanding my bill, but from customer service. I have been with Verizon for a very long time, and it is a continuing problem. Where did Verizon get the 'OK' to drop my data package off my plan? Who authorized that?
After calling Verizon and trying to find out the problem, the gentleman told me that when I activated on old phone while I was waiting on my new Droid to arrive, my data package was dropped off and I "should" have been told about that. When I reactiviated my new Droid, I "should" have called and had them restart my data package. I was not aware that when you activate an old phone that data plan is taken off your plan. In all my years of having cell phones, I never make two years with one phone. I have always, at one point, had to turn on an old phone, and my data package has NEVER changed. Why would I have my data package dropped and why would I have to call Verizon to have it restarted. I would never know to do that unless I was TOLD that my data packaged HAD to be re-added when I recieved my new phone, but I was never told of that.
All of that is beside the point, the point is, Verizon was never given the authorization to change my plan. Never. My bill was taken care of and readjusted, and I am thankful for that. It does not change the fact it is always a hassle with Verizon Customer Service and I am always the one having to PROVE that I am not at fault, or that I was NEVER told of certian things. EVERY TIME I HAVE CALLED CUSTOMER SERVICE, I AM TOLD "I'M SORRY, THEY SHOULD HAVE TOLD YOU THAT."
"they should" does not help my bill with the extra armount of charges.

Problems with dropped calls and no reception on Samsung Continuum

My mother and I both purchased a Samsung Continuum in late March 2011, and have experienced the same problems with the phone. The device drops at least 2-3 calls per day, often on the same conversation; we have not found that location or time of day makes a difference. The phone freezes up frequently, even if no apps are running in the background. We lose our 3G network reception frequently, and cannot access our texts, emails, or the internet. The screen saver kicks in even when we are actively dialing a number, or typing in a text message. The overall performance of the phone is also poor, and it is quite slow much of the time.
We have raised this issue several times with a representative at one of the Verizon stores, but he states that he can find no problem with the phone, and that these issues may not be covered under our insurance plan. None of my friends with non-Samsung phones are having the same problems with phone reception and performance. I am aggravated enough with these issues that I am considering reactivating my old Blackberry, which worked like a charm.
I am not upset that my phone has not been updated to Android 2.2. I just want the phone to perform as stated, and not fail at its primary function: making and receiving phone calls. I am not certain if these problems originate with the phone, Verizon, or Samsung, nor do I care. I just want to resolve these issues as soon as possible, or I will have to look at other alternatives.
Thank you.

If this doesn't work...now what??? I have a useless $400 plus piece of unreliable junk. My Motorola Razor was ions more reliable than this phone...very, very sad but true.
What carrier were you using with the Razor? AT&T? Same area?
Dave M.
MacOSG Founder/Ambassador  An Apple User Group  iTunes: MacOSG Podcast
Creator of 'Mac611 - Mobile Mac Support' (designed exclusively for an iPhone/iPod touch)

Problems with Mail, Safari and iTunes after updating to 10.5.6

Hi all,
after installing 10.5.6 I have problems with Mail, Safari and iTunes.
The time to open mails, websides and iTunes store is increasing dramatically since the update. If I open a webside parallel with Safari and Firefox, Safari needs minimum 15 times longer to open the complete side. Mails containing HTML-code also needs a long time to be opened. Tha same Problem with iTunes store. Connecting to the Store costs at least 30 - 40 seconds. And unfortunately for every iTunes store side I open. Its terrible
Any idea or workaroung to solve that problem?
Regards
Michael

First, run Disk Utility and repair permissions and then restart.
I installed the 10.5.6 Combo update. Sometimes things get "lost in the translation" when you use Software Update depending on your installation. Perhaps you can download 10.5.6 Combo from the website and install it from your desktop.

Problem with K8T Neo and cdrom

Similar Messages

Maybe you are looking for