Problems logging clips!

I have some problems logging clips from my SONY camera. Even if I put IN/OUT marks when logging, Premiere doesn't stop recording at the OUTmark when batching. It just keeps going. Why is this??!
Thank you!
Simon

Welcome to the forum.
Can you give us some details on your Sony camera? As mfgr's sites can be heck to navigate, if you can give both the model number, and also the full specs. of the files, that would be helpful.
Next, please tell us about the Project/Sequence, that you are Capturing into, plus your Preferences>Capture settings?
If you are Capturing SD material, you might have more luck with Scenealyzer, and if HD, then more success with HDVSplit.
Good luck,
Hunt

Similar Messages

Digitizing Pre-Logged Clips: Drop Frame/Non-Drop Frame Discrepency

I have about 100hrs of DV NTSC footage that has been logged and now I need to capture it.
Everything seemed good to go:
• I ctrl+click the clip intended to capture
• Select 'batch capture' (it initializes)
• Settings are (apple setting) DV NTSC 48kHz
• I click okay and I get an error message that reads:
"WARNING: You are about to capture drop-frame media to a non-drop frame clip. If you proceed, you may experience changes in logged in and out points, problems relinking media, or removal of master clip relationships."
Now, the setting noted above is set at 29.97 not 30.
I tried to see if there was anything I could select/deselect in the logged clips and came up dry.
I made duplicated the apple setting and changed the fps to 30. This yielded no error message but did on the second clip I tried.
Does anyone have any idea on how I should be troubleshooting this?
Due to the high volume of footage, and workflow schedule, I'd really rather not screw this up.
I turn to you my faithful FCP gurus.
Thanks.
Ian
p.s. I'm running FCP v.5.1.4

Just check your timecode accuracy before you get any further... i.e. does the timecode in the captured clip match the code that's on the tape. If so, you're good to go on... if not, I'd recapture using the proper TC... it's pretty easy if you do it from the tape in the Log and Capture window.
Jerry

Problems capturing clips

I using the latest version of FCP with a Blackmagic card. Everything has been working fine until today. I'm having problems capturing clips. I'll start Log & Capture, grab a clip, the window displays it is capturing it, and then when I look at the logging bin, my clip is not there. But if I look in the capture scratch folder, the clip is there.
Now, if I try to import that or any other clip, FCP gives me an error message. Does anyone know what could be wrong? I would appreciate your help.

Probably a Black Magic issue so be prepared to talk to them.
To debug this, you have to take the Black Magic stuff out of the equation to determine if FCP is at fault. If you have any DV device, try to capture from it.
bogiesan

Batch capture logged clips makes subclips that are invisible in sequence

Any ideas?
I log a series of clips (the icon is the square master clip icon). They are offline until I batch capture. However, once I batch capture, they become subclips(jaggy-edge subclip icon). They can play in the viewer and they are viewable in Quicktime. However, once I put them in the sequence, they are only black, even after rendering. HOWEVER, if I do a capture now off of the SAME tape w/ the SAME settings it will play just fine (after render) in the SAME sequence.
Anyone else experiencing this? Thanks in advance
Vicky
Power Mac G5 Mac OS X (10.4.2) FCP 5.01

Okay, finally able to do a couple of tests. I started a new project w/ settings for capturing good ol' NTSC DV, logged some footage and then batch captured (ntsc footage) -- no problem at all. The clips were clips, not subclips. Then I went into a project for DVCPro HD 720 30p, and pulled some clips from my original low res project into the HD project. Made those offline, then batch captured those at the full HD resolution. Not a problem there either. Then I went back into the original low res project, made a clip offline, recaptured it at full HD res, no problem. Soo.... I think there is some connection between what I've been capturing at my "low res HD" setting and the problem of turning the logged clips into subclips upon capture.
All that said...I think I'm ok. At least I know now when I do need to capture it all in full HD res, I'll be able to, and it will relink into my project correctly as visible clips.
Also, how can you mark somthing "helpful' if it has already been marked "solved"...it is not undoable, correct?
Dual 2.7 GHz PowerPC G5 Mac OS X (10.4.5) 2 GB RAM

Change setings for logged clips?

Hello-
I've just logged a ton of footage but have just now realized that I've logged all of my clips with 16 tracks of audio, when I only need 2. This a problem because if I capture with 16 tracks of audio, my capture will stutter and drop frames.
How do I change the audio settings of logged, un-digitized clips in my bin?
Thanks,
Jason

Figured it out:
1) Change my capture settings to what I wanted (1V, 2A)
2) Select the bin I want to capture
3) Right click, select "Batch Capture"
4) In Batch Capture Window, UN-check the box for "Use logged clip settings"
5) FCP will then capture at whatever your current settings are
Thanks!
Jason

Logging Clips

I am going to be starting a project that requires me to take multiple clips off the same tape. I want to play the tape and mark my in and out points then hit log clip..then have it save the clip as no media. Once i complete the entire project, then I want to hit capture project.. and then it will go get all my clips at once on its own... But when i try it, i hit capture "clip", it immediately captures the clip and does not log it. What is the best way to fix this problem?
i am using final cut express hd

Tom has spelled out the problem.
FWIW, this was a non starter issue for me and why I went directly to FCP (now known as Final Cut Studio).
The price difference is significant but does include a number of very powerful programs.
good luck.
x

Active Directory accounts problem logging in to Mavericks

We have twenty iMacs in a lab and five in an Internet café, all wired to a multiple subnet network. OS X Mavericks is bound to Active Directory. Frequently OS X Mavericks behaves as if the network user account password is entered incorrectly until the iMac is restarted. This did not happen when we had Mountain Lion. We never have problems logging in to Windows computers bound to Active Directory.

We have twenty iMacs in a lab and five in an Internet café, all wired to a multiple subnet network. OS X Mavericks is bound to Active Directory. Frequently OS X Mavericks behaves as if the network user account password is entered incorrectly until the iMac is restarted. This did not happen when we had Mountain Lion. We never have problems logging in to Windows computers bound to Active Directory.

Error: There was a problem logging on to SAP BusinessObjects Enterprise

I am trying to use Crystal Reports Enterprise XI 4.0 with BusinessObjects Enterprise 4.0 using a Bex Query on an SAP NetWeaver 7.01 SPS 9 BW system. I have been using the SAP Press book u201CIntegrating SAP BusinessObjects BI Platform 4.x with SAP NetWeaveru201D as my guide, attempting to follow it step by step. Please bear with me as I have only started working with this set of products within the last month. (Very new at this and do not have a very good grounding of the way it all works together. Trying to learn as quickly as possible as I am expected to support this set of tools for our developers / users.)
I have been trying to follow along with the book to get everything connected. At this point, I have BOE set up to attach to the SAP NetWeaver BW system. I have created a test Bex Query on the BW system. From within BOE, using CMC, I can configure the Bex Query as an OLAP connection. I have set it up for SSO. I have also exchanged certificates between the BOE and the SAP NetWeaver systems which I believe will allow the exchange of tokens.
I then go into Crystal Reports for Enterprise XI 4.0 on my PC. (I am running Windows 7 64-bit on the PC. I installed the BOE 4.0 suite of client tools except for SAP BO Live Office and SAP BO Analysis for MS Office). I can attach to my BOE system and can browse to see the OLAP connections in the BOE. I then try to select one as the data source for a new report. I then get a pop-up window stating:
   Unable to Logon
     There was a problem logging on to SAP BusinessObjects Enterprise.
       Please check your logon credentials and make sure your network is properly configured before trying again. If the problem
       persists please contact your Administrator.
I cannot find a log / trace / error file on my PC, the BOE system or the BW system to indicate any additional information as to what the root problem is. Has anyone seen a similar error and might know where I can find more information, how to increase trace levels so that I get some additional information or provide hints as to what the root problem might be?
I am also trying to figure out how the authentication works between the PC, BOE and SAP NetWeaver. If using a token, there has to be consistency with the username (or some value) and I am not certain that is happening. Right now, my BOE sources its UME from the SAP NetWeaver BW system. So its user accounts are in the form SID123/ACCOUNT where SID is the SID of the SAP NetWeaver system and the string u201C123u201D is the client on that SID. When I log into the BOE system from within Crystal Reports, I am using the account in that format whereas the account on the SAP NetWeaver BW system in actuality is only the string ACCOUNT. So is the token stripping the string u201CSID123/u201D from the account name when it is sent so that the accounts match? Or do I have to manually configure some kind of account alias (in the BOE system?) so that the two recognize each other? Or something else?
Any hints or ideas around where I can find additional information or where I have gone wrong, would be greatly appreciated.
Thank-you in advance,
Deb Nugent.

Henry,
Many thanks and excellent suggestions. But I am still not able to get this to work and (once again) am stuck.
RE: Server Connections: When I check my server connection, I have not ticked SSL and am using the non-secure server port for my BOE system. When I click on u201CTest connectionu201D, I can successfully log in using my username / password on the SAP NetWeaver BW system. If I tick the SSL box without changing the port, I get the error message u201CFailed to establish a connection. The cause was u201CCannot connect to SAP BusinessObjects Enterprise at this time. Please try again later.u201D If I tick the SSL box and change the port to use the secure server port for the BOE system, I get the same error.
RE: Preferences: I am using the default settings under Preferences -> Network Settings. We do not manually configure proxy settings on our network so I have ticked u201CUse system proxy configurationu201D and under SSL settings, have ticked u201CUse system keystore / trust storeu201D. I have swapped keys between the BOE system and the SAP NetWeaver system but I have not swapped any keys between my PC and the BOE system or the SAP NetWeaver system (which I do not expect to do but am mentioning here in case I am wrong).
RE: BILaunchPad: I do not have any references for BILaunchPad. Is this u201CWeb Intelligence Rich Clientu201D? If so, I tried starting it, it reported an error: u201CAn error occurred at session creation.u201D Details showed u201CSSL mode is being requested but the following argument(s) are not present: passphrase (FWM 01012)u201D I went into the CMC and checked my SAP connections under Authentications. On the tab u201COptionsu201D, there is the section u201CSAP SSO Serviceu201D where I typed in the KeyStore password. When I created the key store file, I only specified a keystore password and did not specify a private key. Originally, I had it set with the private key blank with the correct password on the keystore. I also tried entering the same password as the private keystore and saving it. I verified that the connection services for Web Intelligence had restarted but I still am getting that same message when I try to start the Web Intelligence Rich Client.
At OS level on the BOE server, I logged in as my boe1 account and checked the parameters that can be entered for the PKCS12Tool.jar file that I used to create the ketstore file I had used. There does not appear to be an option for anything other than the keystore password. There is no private key password field listed.
I searched for the FWM 01012 error and found the HTML and PDF help files form SAP explaining errors. However, it only states u201CEnsure that all SSL arguments are presentu201D but gives no details as to what, exactly needs to be checked.
I will be talking with co-workers today to see if any of them can make sense of this (anoterh set of eyes sometimes helps). Any other suggestions about areas to look for addiitonal details / increased traces / logs?
Deb Nugent.

Sales order cannot be rejected -problem log status item status is incorrect

Hi,
I need to reject this particular sales order, but when i try to reject it says to check the problem log which states that the item status is incorrect. It says subsequent documents exists for some lines even though no documenst are attached.
There were a delivery attached to this order earlier but that has been archived. I ran repors SDVBUK00 etc but nothin seem to sort this issue..
I just need to reject the whole sales order. does anyone know any reports or somethin to rectify this issue.
Thanks
Keshini

Dear Keshini,
Could you please update with the process of Delivery Document Archieved?
I mean, had you reversed the delivery (T. Code: VL09) and then deleted the items from reversed Delivery Doc (T. Code: VL02N), before deleteing the Delivery Doc?
Was there any subsequent document for Delivery Doc.?
Best Regards,
Amit
Note: Also, check with Copy-Control settings for Order-to-Delivery (T. Code: VTLA)
1. Field: Update Document Flow is marked ticked at
Item (Dialog Structure) --> Item Category --> Control data
2. Field: Pos./neg. quantity with entry "+"

Hi, so I keep having problems logging onto the iTunes store in iTunes and I get this error message: "iTunes could not connect to the iTunes Store. An unknown error occurred (0x80090318) Make sure your network connection is active and try again."

Hi,
So I keep having problems logging onto the iTunes store in iTunes where an error message pops up saying: "iTunes could not connect to the iTunes Store. An unknown error occurred (0x80090318) Make sure your network connection is active and try again."
How do I fix this?

Hey thatssoivi,
If you are having an issue with being unable to connect to the iTunes store, I would suggest that you troubleshoot using the steps in this article -
iTunes for Windows: iTunes Store connection troubleshooting - Apple Support
Thanks for using Apple Support Communities.
Be well,
Brett L

Problem Logging it to Int Rep and Int Dir of SAP XI

Hi,
I m using SAP XI 3.0, I am maintaing 2 systems, one as server and one as client. In the client system I have installed J2e engine and SAP GUI. I have problem logging in to Integration rep and Int Dir in the Client system. I have no logging problem in SERVER, but I have in Client system.
So pls help me in this regard....
!!!THANKS IN ADVANCE!!
Sunil Shetty

Hi,
If its a problem in the exchange profile, then how is it possible to log in to the SAP XI Server, which is having the same use name and password.
User Name and Pass Word of Server System is Same as the Client system.I can log in to the server but I am unable to log in to client system which is another system.
Thanks in advance.
Sunil Shetty

Any way to re-capture logged clips to anamorphic setting?

Hello-
I have an FCP project with containing clips with a 16:9 aspect ratio captured with 4:3 aspect ratio setting. I'd like to recapture all of the logged clips using the anamorphic capture setting. However, all the capture information is embedded in the clips, so, even if I set the capture preference to anamorphic, the clips still come through as 4:3 when I attempt to re-batch capture.
Is there anyway to globally change the capture setting to anamorphic with clips that have already been captured at 4:3?
Thanks....

If you are talking about DV, there is absolutely no need to recapture. The difference between 4:3 and 16:9 DV is really in how FCP interpretes the pixels- they are both 720x480.
Go to the Browser and you can add a check mark in the ANAMORPHIC column. Voila, you now have anamorphic clips without recapturing.
x
edit: I'm slow slow slow. To elaborate on what Tallguy said, if you need to fix the aspect ratio of the clips you've already placed in a 16:9 timeline, select all the clips in the timeline, right (control) click and from the popup menu select: Remove Attributes>Video Attributes>Distort.

I have just upgraded from an iPhone 3Gs to an iPhone 5. I am trying to transfer all my content via icloud but having problems logging in - it keeps telling me the server is not responding. Nano sim hasn't yet been registered - does this affect things?

i have just upgraded from an iPhone 3Gs to an iPhone 5. I am trying to transfer all my content via icloud but having problems logging in - it keeps telling me the server is not responding. Nano sim hasn't yet been registered - does this affect things?

Have you activated your phone with your carrier yet?

Problem Logging into only one of many computers

1. I have two desktop computers. One is hard wired to a linksys router and works great. The other desktop that has a problem logging into my email account. See (5) below. 2. First you must know that I also have an apple mac that is connected via the Router and it also works fine running OSX. 3. I have a Dell Laptop running Vista connected via the Router that runs fine. 4. Have another Dell Laptop running Win 7 is connected via the Router that runs fine. 5. I have this desktop running Win XP pro that is my problem. This is how the problem goes: I get to what appears to the correct login page; Type in the correct user and PW info; execute by clicking on the correct button; Nothing happens; I try several other ways; I click on the "signin" box at the extreme top right and nothing happens; I click on another box that ask for my location and a new window appears asking for my addres and zip code. I eventually get to the email. Now at this moment I look at the top of this my current window and I see that my location is shown and I am signed into verizon to write to you. There is a block that reads "signout". What is going on?

And one more small detail. After I have this problem there's a crash file in ~Library/Preferences called 'com.apple.iLifeAssetManagement.crqash.plist'. It's cryptic, but it says:
bplist00“_AssetManagmentCrashDetailsKey_AssetManagmentCrashCheckerKey°’
_&AssetManagementAgentProcessInfoDateKey_3AssetManagementAgentProcessInfoProcess IdentifierKey_0AssetManagementAgentProcessInfoSupportsDeleteKey_7AssetManagement AgentProcessInfoSupportsSharedStreamsKey_0AssetManagementAgentProcessInfoExecuta blePathKey3A∑Ëô¿U∞y— _i/Applications/iPhoto.app/Contents/Library/LoginItems/PhotoStreamAge nt.app/Contents/MacOS/PhotoStreamAgent÷_&AssetManagementAgentProcessInfoDateKey_ 3AssetManagementAgentProcessInfoProcessIdentifierKey_0AssetManagementAgentProces sInfoSupportsDeleteKey_<AssetManagementAgentProcessInfoSupportsSharedStreamsVide oKey_7AssetManagementAgentProcessInfoSupportsSharedStreamsKey_0AssetManagementAg entProcessInfoExecutablePathKey3A∏Ü“@Ôx î _i/Applications/iPhoto.app/Contents/Library/LoginItems/PhotoStre amAgent.app/Contents/MacOS/PhotoStreamAgent
π

Changing Media Start and End of Logged Clips

This should be really simple, and I'm sure I'm just overlooking something. I am trying to recapture some clips in Final Cut Pro and it was fine until I came to a clip that gave me the "timecode error - pre roll, post roll, etc" message. The Media Start on the problematic clip is at 00:00:01:04 - I want to manually change this time to allow pre-roll. The timecode in the "In" and "Out" sections isn't making a difference and seems unrelated - no matter what I put it to.
So I just want to edit the Media Start time as I'm sure this would remedy my timecode error when trying to capture... but I can't edit that field. What am I doing wrong? How do I change the Media Start time?
I could recapture the whole tape independently but I already have sequences edited based on my previously logged clip. Any help would be greatly appreciated. Thanks!

If you are re-capturing then you must have used Capture Now to get the clip first time round or you would have run into the same trouble with pre-roll. You'll have to capture the clip again using the same method. Of course, the chances of getting the same start and end code using Capture Now are slim, but if you can get in earlier and out later then you should be able to manually re-connect the clip.
rh

Problems logging clips!

Similar Messages

Maybe you are looking for