Problems updating the BAM database

Hi Guys,
I have an activity that runs for a long time and after executing for about 15-16 mins it causes the following exception.
Did somebody else also faced this problem ever? I have tried configuring all possible timeout parameters but all in vain.
Any help would be highly appreciated.
Thanks,
MK
EXCEPTION DETAILS
Problems updating the BAM database. Reason:Unable to connect to the database.
Caused by: A lock could not be obtained within the time requested
fuego.analyzer.UpdaterRuntimeException: Unable to connect to the database.
     at fuego.analyzer.UpdaterRuntimeException.cannotConnecToDatabase(UpdaterRuntimeException.java:80)
     at fuego.analyzer.UpdaterRunner.synchronizeMetadata(UpdaterRunner.java:494)
     at fuego.analyzer.UpdaterRunner.run(UpdaterRunner.java:273)
     at fuego.analyzer.UpdaterRunner.runUpdater(UpdaterRunner.java:176)
     at fuego.server.service.BAMRunnerService.runUpdater(BAMRunnerService.java:62)
     at fuego.server.execution.BAMUpdater.execute(BAMUpdater.java:33)
     at fuego.server.execution.DefaultEngineExecution$AtomicExecutionTA.runTransaction(DefaultEngineExecution.java:290)
     at fuego.transaction.TransactionAction.startBaseTransaction(TransactionAction.java:465)
     at fuego.transaction.TransactionAction.startTransaction(TransactionAction.java:543)
     at fuego.transaction.TransactionAction.start(TransactionAction.java:216)
     at fuego.server.execution.DefaultEngineExecution.executeImmediate(DefaultEngineExecution.java:116)
     at fuego.server.execution.DefaultEngineExecution.executeAutomaticWork(DefaultEngineExecution.java:56)
     at fuego.server.execution.EngineExecution.executeAutomaticWork(EngineExecution.java:42)
     at fuego.server.execution.ToDoItem.executeAutomaticWork(ToDoItem.java:265)
     at fuego.server.execution.ToDoItem.run(ToDoItem.java:536)
     at fuego.component.ExecutionThread.processMessage(ExecutionThread.java:752)
     at fuego.component.ExecutionThread.processBatch(ExecutionThread.java:732)
     at fuego.component.ExecutionThread.doProcessBatch(ExecutionThread.java:138)
     at fuego.component.ExecutionThread.doProcessBatch(ExecutionThread.java:130)
     at fuego.fengine.ToDoQueueThread$PrincipalWrapper.processBatch(ToDoQueueThread.java:429)
     at fuego.component.ExecutionThread.work(ExecutionThread.java:816)
     at fuego.component.ExecutionThread.run(ExecutionThread.java:395)
Caused by: SQL Exception: A lock could not be obtained within the time requested
     at com.ibm.db2cs.m.j.generateCsSQLException(Unknown Source)
     at com.ibm.db2cs.m.b.wrapInSQLException(Unknown Source)
     at com.ibm.db2cs.m.b.handleException(Unknown Source)
     at com.ibm.db2cs.m.d.handleException(Unknown Source)
     at com.ibm.db2cs.m.t.handleException(Unknown Source)
     at com.ibm.db2cs.m.s.closeOnTransactionError(Unknown Source)
     at com.ibm.db2cs.m.s.movePosition(Unknown Source)
     at com.ibm.db2cs.m.s.next(Unknown Source)
     at fuego.jdbc.FaultTolerantResultSet.next(FaultTolerantResultSet.java:553)
     at fuego.analyzer.Updater.loadInstanceInfoValues(Updater.java:1039)
     at fuego.analyzer.Updater.loadInstanceInfoValues(Updater.java:988)
     at fuego.analyzer.Updater.loadInstanceInfo(Updater.java:982)
     at fuego.analyzer.Updater.synchronize(Updater.java:252)
     at fuego.analyzer.UpdaterRunner.synchronizeMetadata(UpdaterRunner.java:480)
     ... 20 more

Good morning justinmm357,
I would be more than happy to help delink the secondary email address from your My Best Buy™ account. Please send me a private message with the information below, by clicking on the blue button in my signature, and I will make sure that everything is up-to-date.
Name
Phone #
Mailing address
Email address (primary and secondary)
Thank you for reaching out to us on the forum and for being a My Best Buy™ member!
Derek|Social Media Specialist | Best Buy® Corporate
Private Message

Similar Messages

There is a problem with the Office database - Office 2011

Good day!
I recently installed Office 2011 for Mac and i'm getting the following error message: There is a problem with the Office database. Excel comes up with the error message but i am able to get past the error and open the application, but it freezes when I try on Word. I have to force quit the application to close it completely.
I've searched online and tried all the suggestions - even those from the discussion board: Problem with Office Mac 2011 database. I've completely removed traces of the software : http://support2.microsoft.com/kb/2398768 and reinstalled using the disc, as well as followed suggestions to rebuild the database. I also installed the latest Office update: http://www.microsoft.com/en-us/download/details.aspx?id=44026 from Excel (As it was the only one I know of that's functioning after the error message) but to no avail.
Here are the tech specs:
OS X
version 10.9.5
Office 2011 for Mac
Version 14.4.4 (140807)
Update: 14.4.4
Hope you guys can point me to the right direction. Any suggestions are greatly appreciated.

Best ask question on one of the Microsoft boards.
Could try NeoOffice.
https://www.neooffice.org/neojava/en/index.php

There is a problem with the Outlook database. Your database could not be rebuilt. [-18000]

For home use, I recently changed from Windows PC to MacBook Air. I have an iPhone 4 which I synched without problem to the PC. Since I have used Outlook for years on Windows and trusted advisors assured me Microsoft Office on the Mac is the same as Microsoft Office on Windows, I decided to continue using Microsoft Office. Because I cannot get my Outlook calendar to sync reliably to iCal / iPhone and because I have found a small but meaningful number of features I use daily in Outlook Windows do not work on Outlook Mac, I have never been in so much pain!
The latest problem is Outlook does not complete startup. I get this error:
There is a problem with the Outlook database. To use the database, you must rebuild it using the Database Utility.
I run the utility but it never completes successfully.
Step 1 of 5: Scannning...
Step 2 of 5: Verifying...
Step 3 of 5: Copying records to new database...
Step 4 of 5: Recovering data...
Your database could not be rebuilt. [-18000]
I have found many articles about this problem but they all seem to assume that you can successfully start Outlook then you rebuild the database to fix data corruption in Outlook.
What if I Outlook never completes startup?

Here are the steps that solved the Outlook data corruption problem.
http://answers.microsoft.com/en-us/mac/forum/macoffice2011-macoutlook/your-datab ase-could-not-be-rebuilt/5caff467-3ab2-464a-9fe6-00ad913b5f2e
The question was: Your database could not be rebuilt
The key is to create a new Outlook Identity, remove the database file, then copy your data records into the new identity and use the Outlook database utility to rebuild the database.
It's a wonderful feeling to see Outlook start up successfully after a few days of downtime!

I have a problem updating the new ipod touch 5th generation

I have a problem updating the new ipod touch 5th generation and I need help:
With each attempt I receive the message:
iTunes has detected an iPod in recovery mode. You must restore this iPod before it can be used with iTunes.
The iPod only displays a USB cable with an arrow pointing to an iTunes logo.
I receive a "Are you sure..." message with the 2 options, one to Restore and Update and the other to Cancel.
Each time I have selected the Restore and Update button and then moved through the acceptance screens. Then iTunes begins to download the iOS 6.0.1 Software Update, which usually takes about 50 minutes. During the download I will receive messages that an iPod has been found in restore mode.
After the download is complete no update occurs to the iPod and iTunes displays the Device Summary screen showing derive Name as iPod and all other items as n/a.
The iPod was working great without any known issues prior to attempting to update the OS.

Maybe:
iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
Unable to contact the iOS software update server gs.apple.com
Error 1004, 1013, 1638, 3194: These errors may be the result of the connection to gs.apple.com being redirected or blocked. Follow these steps to resolve these errors:
Install the latest version of iTunes.
Check security software. Ensure that communication to gs.apple.com is allowed. Follow this article for assistance with security software. iTunes for Windows: Troubleshooting security software issues.
Check the hosts file. The restore will fail if there is an active entry to redirect gs.apple.com. Follow iTunes: Advanced iTunes Store troubleshooting to edit the hosts file or revert to a default hosts file. See section "Blocked by configuration: (Mac OS X/Windows) > Rebuild network information".
Try to restore from another known-good computer and network.
If the errors persist on another computer, the device may need service.

How can I update the QuickLook database?

About 10 days ago my dock in Leopard crashed and I could not find it without restarting. Now I see in the console at startup:
Dock[150] [QL ERROR] Generator database update takes too long... we will use what we currently have
Since I have updated the Info.plist on my .tex files to conform to public.plain-text I would like quicklook to take note of it, but nothing I do will force it to take effect. On the command line qlmanage -r shows "resetting all generators" but qlmanage -m ends with the statement "generators change detected: NO". Any help would be greatly appreciated. Thanks

This is by no means a complete answer. I still get the error messages in the console. However, I now have a partial answer to my question. After I log in, I run Cocktail 4.0.1 for Leopard, Select System then Databases. Then Rebuild Launch Services database with Restore default file associations enabled. About three quarters of the way through executing /System/Library/ScriptingAdditions/StandardAdditions.osax/Contents/MacOS/uid the .tex files lose the icon when selected, show the label "TEX" and can now be viewed with a touch of the space bar. What a pleasure. To the poster who recommends staying with Tiger, I say I never want to give up the pleasure of having Quick Look a spacebar away for all my files.
Unfortunately, when I logout, restart or shutdown, once again, none of the org.tug.tex files are registered as public.plain-text and only the icon appears. To regain Quick Look capability I have to Rebuild Launch Services database. It only takes a few minutes, but I would like to automate the process somehow at login, but I have no idea how to do this. I will probably stay logged in for long periods of time, hoping that an update in the future will resolve this.

Problem with the standby database?

i am working on 10gr2 on rhel4.
i am creating a standby database on the same servr machine.
i have taken a cold backup of the primary database and edited the parameter files for the primary as well as the standby database.
the only problem is that i am unable to open the standby database in the read only mode. following is the problem:
SQL> alter database open read only;
alter database open read only
ERROR at line 1:
ORA-16004: backup database requires recovery
ORA-01152: file 1 was not restored from a sufficiently old backup
ORA-01110: data file 1: '/data02/logical_stdby/prdbs02sb/oradata/system01.dbf
thanks

if i issue this command on the primary database, i get
SQL> select status, error from v$archive_Dest where dest_id=2;
STATUS ERROR
ERROR ORA-01031: insufficient privileges
what is the reason, my logs are not propagating to the standby.
also some entries from the primary alert log file is as below:
Thu Oct 4 15:19:26 2007
Errors in file /opt/db/oracle/admin/prdbs02/bdump/prdbs02_arc1_17509.trc:
ORA-01031: insufficient privileges
PING[ARC1]: Heartbeat failed to connect to standby 'PRDBS02SB'. Error is 1031.
what is the reason??? please let me know if anything else is required for troublshooting

Problem updating the Firmware on a PCI-7334

About me: I am pretty new to the Labview/NI landscape so I may be missing something here! That said im very technically aware in general and believe I understand what is going on here.
Background: This NI PCI-7334 board has been taken from currently unused project stock so current physical condition of board is not really known (ie was not recently working) although it appears to be in good physical order.
Attempting to setup a new Labview 7 Express development environment on new PC hardware with a clean build of Windows XP Pro SP1 along with 1 x IMAQ PCI-1411 and 1 x IMAQ PCI-1408.
Attempting to update the PCI-7334 with the latest firmware in NI Motion 6.1.2. I select the option "Update All Firmware Sectors" f
rom the firmware tree by right mouse clicking. It starts off with the buttonless (ie No Cancel Button) file transfer progress dialog box. But after about 30 seconds I keep getting the error "Error configuring the board for download. Please ensure that the board is in a reset state and that no other application is communicating with it."
Existing Firmware versions are listed in NiMAX as:
68331 - 6.00.3012
DSP - 6.00.3008
FPGA1 - [BLANK*]
FPGA2 - [BLANK*]
*Listed in tree without a version
Unusually under the General listing I get "0" for the device serial number!
When I go into the "Status" area and choose the "Reset Device" option I eventually get these status lights (red):
Ready to Receive
Power Up Reset
Modal Error Message
0x80 Move Complete Status
I have tried removing all other cards from the PC to ensure there is not a compatability issue.
At this stage it would appear that it is a hardware problem so I was wondering what options I have available to g
et this card repaired. Is repair by NI economically viable or is a new puchase a better approach? IE are repairs done at a fixed price or based on materials and labour?
Please advise!
Thanks, Rod.
Attachments:
NI_PCI-7334_Firmware_Update_Error.zip ‏115 KB

I agree with your diagnostics. It looks like something went wrong during the last firmware update. The only solution for this problem is to send the board for repair.
NI has fixed prices for repairs which are much cheaper than buying a new board. Please contact your local NI branch for details.
Best regards,
Jochen Klier
Applications Engineering Group Leader
National Instruments Germany GmbH

Connection problems with the Olite database

Hi,
I have a problem when I want to execute a BPEL Process from the process manager. I get a java.sql.SQLException with the following message "[POL-3207] a corrupted data page was detected".
The fact is that another person (with his own account) installed the SOA Suite and executed the same code before and it worked. But when I connected to the computer remotely using my account and tried to execute the BPEL Process this error appeared. Since then even the former user has the same error message. Is there a way to solve this problem or do I have to reinstall the SOA Suite? Is there a problem using the SOA Suite with different windows accounts?
When I also try to see the instances after executing the process, I get the following error:
The following exception occured while processing this request:
Cannot find instances.
An attempt to fetch the instances using the where condition "" from the datastore has failed. The exception reported is: [POL-3207] a corrupted data page was detected
Please check that the machine hosting the datasource is physically connected to the network. Otherwise, check that the datasource connection parameters (user/password) is currently valid.
sql statement: SELECT * FROM admin_list_ci WHERE ci_domain_ref = 0 ORDER BY ci_modify_date desc
Oracle BPEL Console v10.1.3.1.0
Is there a GUI program to access the Olite DB instead of using the mobility sql in the command prompt?
Any help would be greatly appreciated.
Amir

Hi rajesh,
You restart your Olite database. You can do one thing.
Goto control panel->Administrative tools->services-> Stop & start Olite multiuser service.
Then try to run the polsql.cmd command.
Hope this works fine.
Cheers,
Abhi...

Space problems with the SAP Database MS SQL 2000

Hi,
Actually, I have a size problem with the database, I have MS SQL Server 2000 with Service Pack4 on a Windows 2003 Server environment that is my DataBase Server of my ERP ECC 6.0. On the other hand I have a storage where I have 229 Gb of free space used only for the database files of the SAP data and the SAP log file.
But when I check the DB space allocation on trx. DB02 I saw this:
3 Database files and 1 transaction log:
The 3 database files are: PRDDATA1 (size 15,313 MB used 15016 MB) , PRDDATA2 (size 14106 MB used 13984 MB), PRDDATA3 (size 14472 MB used 14352 MB) and the log file is PRDLOG1 ( size 1000 MB) all of them with no limit option and growth by 10%.
So I went to the SQL Enterprise Manager and I saw that my Database PRD properties and I got this information:
My database size is 44892.48 Mb size with only 1330.36 Mb of free space and that is alarming.
So the question here is how ,if I have a storage where the sap data is storing with 229 Gb of free space, can I make the database files grow up in order to use all the available space of my storage.
Can you help me please because it is critical being my productive system?
Best Regards
Erik Espinosa

I resolved this issue myself. Thanks for all your help.
Best Regards,
Erik Espinosa

JTree: Problems updating the nodes size

Hi,
I'm trying to update the content of a JTree and I wonder how it
really works, since the paint() method doesn't seem to call the
renderer.
My situation: Imagine a JPanel splited in two by a JSplitPane. In
the left is the tree. Each node in the tree shows two panels, one
aligned to the left, and another to the right. I need that the panel
containing the two use all the available space in the left part of the
Split panel.
My solution: I pass the left JPanel to the tree renderer, so that
it can get the width from it (inside the
getTreeCellRendererComponent()) to build the return JPanel with the
correct size. My logic is that since each time you move the JSplitPane
the JTree paint() method is invoked the renderer can return the
correct JPanel with the correct size that will be painted then in the
screen.
My problem: Doens't work. When I render the tree, the renderer is
invoked, but it doesn't change its size (I can change the color based on the width, but not the node size). Only when I collapse & expand a node, it correctly takes into account the .setPreferredSize() and returns the JPanel with the correct size.
The only way I found to update the tree involves to catch the
JSplitPane event and call updateUI() in the tree, something that, I
think, it's certainly not the correct way to do it.
Any explanation of why this doesn't work would be really great. Any
pointer to a web resource explaining in deep how Swing components work (specially the JTree) would be a godsend.
Thanks,
- Juancho

My situation: Imagine a JPanel splited in two by a JSplitPane. Got it.
In the left is the tree. In the left side of the JSplitPane is a JTree.
Each node in the tree shows two panels,Maybe... on the right side of the JSplitPane are two Panels in which the data depends on which node is selected in the JTree???
Maybe... you have a custom TreeCellRenderer which displays a pair of panels in place of the standard JLabel???
one aligned to the left, and another to the right. To the left of what??? To the right of what???
I need that the panel containing the two use all the available
space in the left part of the Split panel.Panel containing the two what??? I thought the left part of the SplitPanel contained a JTree???

Problems updating the ipad2 - network error message

I keep trying to update the ipad2 thru Itunes - which i updated to 10.5 I keep getting an error message of network connectivity. Called my internet provider, Comcast, and plugged modem directly into laptop. Still a problem. Called Apple and the guy said lower the anti-virus setting. Did that. Still getting this error message and now have had the connection from being on hold to a person ring for nearly 15 minutes. VERY DISAPPOINTED with the three different tech people I have spoken with giving me three different answers, and I'm still not updated. HELP HELP HELP

About iTunes Store authorization and deauthorization
iPod: Troubleshooting songs and audiobooks that won't play
iPod does not play content purchased from the iTunes Store

How to use the myAdapter.Update and OleDbCommandBuilder from dataGridView to update the db2 database

hello,everybody ,it a question makes me crazy .my code is that :
public string tableName = "";
public DataSet ds;
public OleDbDataAdapter myAdapter;
public string sql = "";
private void button12_Click_1(object sender, EventArgs e)
sql = textBox5.Text.Trim();
OleDbConnection Conn = new OleDbConnection(st_contractconn);
Conn.Open();
this.comboBox1.Items.Add(this.textBox5.Text);
try
System.Text.RegularExpressions.Regex r = new System.Text.RegularExpressions.Regex(@"(?<=from\s)\w+(?=\s)");
System.Text.RegularExpressions.Match B = r.Match(sql);
tableName = B.ToString();
OleDbCommand cmd = new OleDbCommand("SELECT * FROM PT_PO",Conn);
Conn.Close();
myAdapter = new OleDbDataAdapter(cmd);
ds = new DataSet();
myAdapter.Fill(ds, "PT_PO");
dataGridView2.DataSource = ds.Tables["PT_PO"].DefaultView;
this.groupBox2.Text = "共查询到" + ds.Tables[0].Rows.Count.ToString() + "条记录" + tableName;
catch (Exception ex)
MessageBox.Show(ex.Message);
private void button26_Click(object sender, EventArgs e)
OleDbConnection Conn = new OleDbConnection(st_contractconn);
Conn.Open();
OleDbCommandBuilder Builder = new OleDbCommandBuilder(myAdapter);
Validate() ;
myAdapter.Update(ds.Tables["PT_PO"]);
Conn.Close();
ds.AcceptChanges() ;
when it run to the myAdapter.Update(ds.Tables["PT_PO"]); it comes out a wrong "对于不返回任何基表信息的 SelectCommand 不支持动态 SQL 生成。" who knows it is why ,my QQ is 501212848,thankyou very much.

Hello,
We were a IBM-DB2 shop for over 20 years, when we moved to .NET we found it was better to use the native DB2 data provider which you can download from IBM for free.
Main objects
IBM.Data.DB2.iSeries.iDB2Connection
IBM.Data.DB2.iSeries.iDB2Command
IBM.Data.DB2.iSeries.iDB2Parameter
So you would not use adapters but write code using the key objects above. Then to get new primary keys we would use
SELECT nextval for SOMETABLE_REF_AUTONUMBER_SEQUENCE from sysibm.sysdummy1
Bottom line is the structure is create a connection, create a command, set the connection and command text along with creating parameters as needed.
Please remember to mark the replies as answers if they help and unmark them if they provide no help, this will help others who are looking for solutions to the same or similar problem.
what is the meaning about you ? db2 cannt using adapters to update the datebase?

Problem updating the infotype 1208 subtype ALUM

Hi,
My requirement is to update the infotype 1208 subtype ALUM with the Value "YES" when I terminate a employee in PA40. ( immediately).
I am using the FM - HR_INFOTYPE_OPERATION which doesn't seem to work.
I tried running a BDC for PA30 , but it is not allowing me to edit the employee and says that i am processing him.
I feel this is an issue with locks. But not sure about how to go with.
Are there any standard classes available or any other method to use to update this infotype while terminating.
Regards,
Karan.

Hi,
try using this method, this will convert the OLD_IMAGE, NEW_IMAGE, parameters into pnnnn table.
this code is the following class.
CL_IM_BR_SALARY_INCREASE,
you need to create your own method, copy the parameters as well.
method READ_IMAGE .
FIELD-SYMBOLS: <f> type any.
DATA: help_prelp TYPE prelp,
        inf_tabname(10).
data: wa_p0008      type p0008,
        wa_p0734      type p0734.
concatenate 'WA_P' p_infty into inf_tabname.
ASSIGN (inf_tabname) TO <f>.
loop at p_image into help_prelp
                  where infty eq p_infty and
                        opera eq p_opera and
                        subty eq '0'.
    CLEAR <f>.
    CALL METHOD cl_hr_pnnnn_type_cast=>prelp_to_pnnnn
      EXPORTING
        prelp = help_prelp
      IMPORTING
        pnnnn = <f>.
      append <f> to pnnnn.
endloop.
endmethod.
Message was edited by:
        javier santana

TS1538 Problems Updating the Apple Mobile Device Driver for ipad4

My iTunes was not recognising my new ipad4 and so I followed Apple guidelines re. Apple Mobile Device Service and found that this was not listed on my laptop.
I then followed guidelines to update the driver - I followed steps to install the usbaapl file, however when I clicked ok to install the following message came up:
"The folder you specified doesn't contain a compatible software driver for your device. If the folder contains a driver, make sure it is designed to work with Windows for 32-bit systems."
Any ideas/tip/advice anyone can offer would be much appreciated! I just want to get my music onto my new iPad :(
Thanks.

See:
iOS: Device not recognized in iTunes for Windows
I would start with
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP

Problem updating the BIOS on Satellite A300

You update the BIOS in the laptop model A300-psagce after the update, the device to be subjected something.
Please help very necessary

Hey buddy,
Does this mean that now after the BIOS update you see only a black screen? Or can you access the BIOS or boot into safe mode?
If your notebook doesnt start anymore you should try this workaround: Remove the battery and AC/DC adaptor. Then wait one hour and connect both devices again. Now you can try to start the notebook again.
If it doesnt work you should go to an authorized service provider. Maybe the ROM module must be reflashed but this can only be done from an ASP.
Good luck!

Problems updating the BAM database

Similar Messages

Maybe you are looking for