RACs nodes can not communicate

I am working with the installation of Oracle 11g RAC on virtual servers.
so far, I create rac1 and rac2 two nodes on virtual server.
after run two virtual mahines, I try to test the network setup, ping the nodes from each other using public address.
I have the following problems;
*rac1:internet connection ;0.k
ip_address:10.45.110.247
subnet:255.255.252.0
gateway:10.45.109.1
*rac2:internet connection:o.k
ip_address:10.45.110.178
subnet:255.255.252.0
gateway:10.45.109.1
if i ping to each other
run ping forever....
if I type,
ssh rac2 cat ~/.ssh/id_rsa/bub >> ~/.ssh/authorized_keys
error;ssh: rac2:Name or service not known.
would you help me!

I have a question with following your instruction;
In my virtual network setting ;
virtual network     summary                  subnet
vmnet0[bridged]     bridged to auto
vmnet1[host-only]    a private network    192.168.65.0
vmnet8[nat]   used to share the host   192.168.183.0
DHCP TAB
vmnet1       192.168.65.0 255.255.255.0 VMNET1
vmnet8    192.168.183.0 255.255.255.0 VMNET8
question;
Choose host only networking -> it means - go to ethernet hardware config. and change" Host-only" in network connection in vmnet8. am I right?
Also ethernet config for the cluster interconnect should not have a broadcast ?????? i do not understand, where do i go to change it?
thank you so much for your help.
by the way, if you have some reference for my problem, please share with me.

Similar Messages

FP2000 status light stays lit red can not communicate

I just tried to update the software on a FP2000 not the status light stays read and can not communicate. any ideas.
Solved!
Go to Solution.

TJE-
Based on the manual for this device, the status light staying lit refers to “the FieldPoint-20XX did not power on correctly.” I would suggest removing all software from this controller and reinstall it.
Regards,
Mike S
NI AE

Node can not join cluster after RAC HA Testing

Dear forum,
We are performing RAC failover tests according to document "RAC System Test Plan Outline 11gR2, Version 2.0". In testcase #14 - Interconnect network failure (11.2.0.2 an higher), we have disabled private interconnect network of node node1 (OCR Master).
Then - as expected - node node2 was evicted. Now, after enabling private interconnect network on node node1, i want to start CRS again on node2. However, node does not join cluster with messages:
2012-03-15 14:12:35.138: [ CSSD][1113114944]clssgmWaitOnEventValue: after CmInfo State val 3, eval 1 waited 0
2012-03-15 14:12:35.371: [ CSSD][1109961024]clssnmvDHBValidateNCopy: node 1, node1, has a disk HB, but no network HB, DHB has rcfg 226493542, wrtcnt, 2301201, LATS 5535614, lastSeqNo 2301198, uniqueness 1331804892, timestamp 1331817153/13040714
2012-03-15 14:12:35.479: [ CSSD][1100884288]clssnmvDHBValidateNCopy: node 1, node1, has a disk HB, but no network HB, DHB has rcfg 226493542, wrtcnt, 2301202, LATS 5535724, lastSeqNo 2301199, uniqueness 1331804892, timestamp 1331817154/13041024
2012-03-15 14:12:35.675: [ CSSD][1080801600]clssnmvDHBValidateNCopy: node 1, node1, has a disk HB, but no network HB, DHB has rcfg 226493542, wrtcnt, 2301203, LATS 5535924, lastSeqNo 2301200, uniqueness 1331804892, timestamp 1331817154/13041364
Rebooting node2 did not help. Node1 which was online all the time (although private interconnect interface was unplugged for a few minutes and then plugged back in). I suppose that if we reboot node2, the problem will disappear. But there should be solution, which keeps availability requirements.
Setup:
2 Nodes (OEL5U7, UEK)
2 Storages
Network bonding via Linux bonding
GI 11.2.0.3.1
RDBMS 11.1.0.7.10
Any ideas?
Regards,
Martin

I have found a solution myself:
[root@node1 trace]# echo -eth3 > /sys/class/net/bond1/bonding/slaves
[root@node1 trace]# echo -eth1 > /sys/class/net/bond1/bonding/slaves
[root@node1 trace]# echo +eth1 > /sys/class/net/bond1/bonding/slaves
[root@node1 trace]# echo +eth3 > /sys/class/net/bond1/bonding/slaves
Now node2 is automatically joining the cluster.
Regards,
martin

Listener on RAC node 2 not accepting user connections

Hey guys i am experiencing a disturbing scenario, i have a 2 RAC node cluster . The problem is that the second listener is not registering any connections . I have verified the services of listener using lsnrctl status (the default name is LISTENER), i also have verified the local and remote listener parameters they are fine but running the fol query shows count =0 against inst_id=2;
SQL > select count() from gv$session where username='XYZ' and inst_id=2;*
Count
0
Any help is appreciated in this regard please.

Yeah i know very well the purpose of SCAN . But web admins are sticking to the vip . Well here is the output of lsnrctl status:-
LSNRCTL for Solaris: Version 11.2.0.1.0 - Production on 11-APR-2013 16:41:55
Copyright (c) 1991, 2009, Oracle. All rights reserved.
Connecting to (ADDRESS=(PROTOCOL=tcp)(HOST=)(PORT=1521))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for Solaris: Version 11.2.0.1.0 - Production
Start Date 10-MAR-2013 13:00:14
Uptime 17 days 2 hr. 42 min. 18 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Listener Parameter File /u01/app/11.2.0/grid/network/admin/listener.ora
Listener Log File /u01/app/oracle/diag/tnslsnr/fedb6/listener/alert/log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=LISTENER)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=5.2.21.1)(PORT=1521)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=5.2.21.7)(PORT=1521)))
Services Summary...
Service "+ASM" has 1 instance(s).
Instance "+ASM2", status READY, has 1 handler(s) for this service...
Service "grid1.xyz" has 1 instance(s).
Instance "grid12", status READY, has 1 handler(s) for this service...
Service "grid1XDB.xyz" has 1 instance(s).
Instance "grid12", status READY, has 1 handler(s) for this service...
Service "xyz" has 1 instance(s).
Instance "grid12", status READY, has 1 handler(s) for this service...
The command completed successfully
and here is tnsnames.ora output :-
GRID1 =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = grid1-scan)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = grid1.xyz)
PRIMARY1_SERV =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = 5.2.21.1)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = grid1.xyz)
(INSTANCE_NAME= grid11)
PRIMARY2_SERV =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = 5.2.21.6)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = grid1.xyz)
(INSTANCE_NAME = grid12)
)

Agenda can not communicate with Exchange server

Hello,
Whenever I start my agenda app on my MBP, I get the message: Agenda can not store the agenda <name> on the Exchange server. I use Office 365's Exchange server. When I use Outlook to communicate with te same Exchange server, there is no problem, but I like to use the native Apple Agenda app.
Anybody got the same problem, and more important, the solution?

Justin, I don't know if this will help but I do remember running into this in the past.
I ended up setting up my mail using our webmail server. Also instead of using my email address I used my login credential in front of the @. Our login credential is not the same as our email. So instead of [email protected] I went with [email protected] and used my password for password at setup of an exchange account. This worked like a charm.

Can not communicate any with Server, BUT I CAN CONNECT SUCCESS FROM "MANAGE SITES"

I can NOT see Server Files in dw cs6 , so i can NOT upload/download or communicate any with Server, BUT I CAN CONNECT SUCCESS FROM "MANAGE SITES"...WELL WHERE THE PROBLEM?

From the File view pop-up menu, choose Remote server

Client can not communicate with MP over https. Certification Problem

Hi All,
I have been fighting with this problem for the last 3 days and couldn't solve yet. So, I hope we can solve it here.
I am trying to install client manually from a usb drive by using the below command.
Ccmsetup.exe /usepkicert smsmp=”srvsccm2012.domain.local” ccmhostname=”sccm.domain.tr” smssitecode=”AUTO”
Client Installs on workstations but only info that I can see under Configuration Manager Properties are:
Client Certificate: None
Connection Type: Currently Intranet
Version:5.00.x.x
So, there is a problem with connection to MP, It can not get policies and certificate info (PKI) etc...
If I try to browse these urls, result is 403 - Forbidden: Acces is denied.
http://siteservername/SMS_MP/.sms_aut?MPCert<o:p></o:p>
http://siteservername/SMS_MP/.sms_aut?MPlist<o:p></o:p>
This makes me think certificates are messed up but if I try to browse my MP with the url below, Result is IIS 8 page.
https://sccmserver.domain.local
I can see these errors in my log files:
CcmMessaging Log errors:
Post to http://”myservername.mydomain”/ccm_system/request failed with 0x87d00231.
Failed in WinHttpSendRequest API, ErrorCode = 0x2ee7.
ClientIDManagerStartup Log errors:
RegTask: Failed to refresh site code. Error: 0x8000ffff
LocationServices Log errors:
Failed to retrieve DNS service record using _mssms_mp_”auto”._tcp.mydomain lookup. DNS returned error 9003
Policy prevents failover to WINS for lookup
LocationServices 8/26/2014 4:18:29 PM
3900 (0x0F3C)
LSGetSiteVersionFromAD : Failed to retrieve version for the site '”AUTO”' (0x80004005)
The ip address of workstation on DNS is correct.
I can ping and resolve the name of MP from workstation.
I want to check if my certificates are OK but I dont know how to make sure certificates are good. Please advise.
By the way, This problem is happening on the newly reformatted workstation, existing workstations can be re-installed with client without problems.
Yavuz Selim Atmaca

Hi Peter,
I checked IIS Logs and I didn't see any error messages.
I checked the certificate requirements and I think there is no problem with them.
certutil -verify -urlfetch command outputs some results that I couldnt understand. Here it is:
ssuer:
CN=mydomain-SRVDC01-CA
DC=mydomain
DC=edu
DC=local
Subject:
EMPTY (DNS Name=selimtestPC.mydomain.edu.local)
Cert Serial Number: 29e6fe37000000005edb
dwFlags = CA_VERIFY_FLAGS_ALLOW_UNTRUSTED_ROOT (0x1)
dwFlags = CA_VERIFY_FLAGS_IGNORE_OFFLINE (0x2)
dwFlags = CA_VERIFY_FLAGS_FULL_CHAIN_REVOCATION (0x8)
dwFlags = CA_VERIFY_FLAGS_CONSOLE_TRACE (0x20000000)
dwFlags = CA_VERIFY_FLAGS_DUMP_CHAIN (0x40000000)
ChainFlags = CERT_CHAIN_REVOCATION_CHECK_CHAIN (0x20000000)
HCCE_LOCAL_MACHINE
CERT_CHAIN_POLICY_BASE
-------- CERT_CHAIN_CONTEXT --------
ChainContext.dwInfoStatus = CERT_TRUST_HAS_PREFERRED_ISSUER (0x100)
ChainContext.dwRevocationFreshnessTime: 7 Hours, 33 Minutes, 49 Seconds
SimpleChain.dwInfoStatus = CERT_TRUST_HAS_PREFERRED_ISSUER (0x100)
SimpleChain.dwRevocationFreshnessTime: 7 Hours, 33 Minutes, 49 Seconds
CertContext[0][0]: dwInfoStatus=102 dwErrorStatus=0
Issuer: CN=mydomain-SRVDC01-CA, DC=mydomain, DC=edu, DC=local
NotBefore: 26.08.2014 14:19
NotAfter: 26.08.2016 14:29
Subject:
Serial: 29e6fe37000000005edb
SubjectAltName: DNS Name=selimtestPC.mydomain.edu.local
Template: ConfigMgr Client Certificate
74 cf 94 a4 5d 72 0f e9 19 d1 36 b4 5c 06 4e 55 12 04 89 26
Element.dwInfoStatus = CERT_TRUST_HAS_KEY_MATCH_ISSUER (0x2)
Element.dwInfoStatus = CERT_TRUST_HAS_PREFERRED_ISSUER (0x100)
---------------- Certificate AIA ----------------
Verified "Certificate (0)" Time: 0
[0.0] ldap:///CN=mydomain-SRVDC01-CA,CN=AIA,CN=Public%20Key%20Services,CN=Servi
ces,CN=Configuration,DC=mydomain,DC=edu,DC=local?cACertificate?base?objectClass=cer
tificationAuthority
---------------- Certificate CDP ----------------
Verified "Base CRL (057a)" Time: 0
[0.0] ldap:///CN=mydomain-SRVDC01-CA,CN=SRVDC01,CN=CDP,CN=Public%20Key%20Servic
es,CN=Services,CN=Configuration,DC=mydomain,DC=edu,DC=local?certificateRevocationLi
st?base?objectClass=cRLDistributionPoint
Verified "Delta CRL (057a)" Time: 0
[0.0.0] ldap:///CN=mydomain-SRVDC01-CA,CN=SRVDC01,CN=CDP,CN=Public%20Key%20Serv
ices,CN=Services,CN=Configuration,DC=mydomain,DC=edu,DC=local?deltaRevocationList?b
ase?objectClass=cRLDistributionPoint
Verified "Delta CRL (057a)" Time: 5
[0.0.1] http://srvdc01.mydomain.edu.local/CertEnroll/mydomain-SRVDC01-CA+.crl
Verified "Base CRL (057a)" Time: 4
[1.0] http://srvdc01.mydomain.edu.local/CertEnroll/mydomain-SRVDC01-CA.crl
Verified "Delta CRL (057a)" Time: 0
[1.0.0] ldap:///CN=mydomain-SRVDC01-CA,CN=SRVDC01,CN=CDP,CN=Public%20Key%20Serv
ices,CN=Services,CN=Configuration,DC=mydomain,DC=edu,DC=local?deltaRevocationList?b
ase?objectClass=cRLDistributionPoint
Verified "Delta CRL (057a)" Time: 4
[1.0.1] http://srvdc01.mydomain.edu.local/CertEnroll/mydomain-SRVDC01-CA+.crl
---------------- Base CRL CDP ----------------
OK "Delta CRL (057e)" Time: 0
[0.0] ldap:///CN=mydomain-SRVDC01-CA,CN=SRVDC01,CN=CDP,CN=Public%20Key%20Servic
es,CN=Services,CN=Configuration,DC=mydomain,DC=edu,DC=local?deltaRevocationList?bas
e?objectClass=cRLDistributionPoint
OK "Delta CRL (057e)" Time: 4
[1.0] http://srvdc01.mydomain.edu.local/CertEnroll/mydomain-SRVDC01-CA+.crl
---------------- Certificate OCSP ----------------
No URLs "None" Time: 0
CRL 057a:
Issuer: CN=mydomain-SRVDC01-CA, DC=mydomain, DC=edu, DC=local
a4 81 a4 bb 01 7e e1 be e2 33 4b 06 5d 00 3c 30 97 93 27 f6
Delta CRL 057e:
Issuer: CN=mydomain-SRVDC01-CA, DC=mydomain, DC=edu, DC=local
52 c5 95 b3 9d c2 9d 22 ee fa 3b c4 b9 04 08 3e 95 98 1d 5c
Application[0] = 1.3.6.1.5.5.7.3.2 Client Authentication
CertContext[0][1]: dwInfoStatus=10c dwErrorStatus=0
Issuer: CN=mydomain-SRVDC01-CA, DC=mydomain, DC=edu, DC=local
NotBefore: 22.10.2010 16:50
NotAfter: 22.10.2025 17:00
Subject: CN=mydomain-SRVDC01-CA, DC=mydomain, DC=edu, DC=local
Serial: 49c50a78f367cdb8466cd34160977233
Template: CA
01 a8 da 41 35 f7 52 be 7a 9b 4d 26 3d ee 33 af c4 e0 9c e0
Element.dwInfoStatus = CERT_TRUST_HAS_NAME_MATCH_ISSUER (0x4)
Element.dwInfoStatus = CERT_TRUST_IS_SELF_SIGNED (0x8)
Element.dwInfoStatus = CERT_TRUST_HAS_PREFERRED_ISSUER (0x100)
---------------- Certificate AIA ----------------
No URLs "None" Time: 0
---------------- Certificate CDP ----------------
No URLs "None" Time: 0
---------------- Base CRL CDP ----------------
OK "Delta CRL (057e)" Time: 0
[0.0] ldap:///CN=mydomain-SRVDC01-CA,CN=SRVDC01,CN=CDP,CN=Public%20Key%20Servic
es,CN=Services,CN=Configuration,DC=mydomain,DC=edu,DC=local?deltaRevocationList?bas
e?objectClass=cRLDistributionPoint
OK "Delta CRL (057e)" Time: 4
[1.0] http://srvdc01.mydomain.edu.local/CertEnroll/mydomain-SRVDC01-CA+.crl
---------------- Certificate OCSP ----------------
No URLs "None" Time: 0
CRL 057a:
Issuer: CN=mydomain-SRVDC01-CA, DC=mydomain, DC=edu, DC=local
a4 81 a4 bb 01 7e e1 be e2 33 4b 06 5d 00 3c 30 97 93 27 f6
Delta CRL 057e:
Issuer: CN=mydomain-SRVDC01-CA, DC=mydomain, DC=edu, DC=local
52 c5 95 b3 9d c2 9d 22 ee fa 3b c4 b9 04 08 3e 95 98 1d 5c
Exclude leaf cert:
58 db 23 c9 81 00 ff 3e de e0 13 da 87 29 66 96 56 45 51 cd
Full chain:
ba 55 5a 92 f0 b4 69 47 01 d7 02 23 1c db 7e 88 66 f2 42 dc
Verified Issuance Policies: None
Verified Application Policies:
1.3.6.1.5.5.7.3.2 Client Authentication
Leaf certificate revocation check passed
CertUtil: -verify command completed successfully.
I just checked SCCM SystemStatus/ Component Status from the SCCM Console and found errors under SMS_MP_CONTROL_MANAGER
component:
"MP has rejected a message from GUID:A90AA88F-FB10-407C-B2ED-DCE41479FBDC because the signature could not be validated. If this is a valid client, it will attempt to re-register automatically so its signature can be correctly validated."
Should I delete all config manager related certificates and re-create them?
Yavuz Selim Atmaca

HT4890 i get a message that my mac can not communicate with my iCloud why???

I get a message that my mac can not comunicate with my icloud why?

Welcome to the Apple Community.
What are you doing when this occurs and what does the message say.

RAC node is not starting

I have 2 node RAC instance in 2 virtual machines. My node 2 ASM instance is not starting after the reboot but node 1 is working fine.
I got below output from Node 2.
srvctl status asm
PRCR-1070 : Failed to check if resource ora.asm is registered
Cannot communicate with crsd
alertlog
[/u01/app/11.2.0/grid/bin/cssdagent(3782)]CRS-5818:Aborted command 'start for resource: ora.cssd 1 1' for resource 'ora.cssd'. Details at (:CRSAGF00113:) in /u01/app/11.2.0/grid/log/ol5-112-rac2/agent/ohasd/oracssdagent_root/oracssdagent_root.log.
2015-03-13 16:38:23.671
[ohasd(3315)]CRS-2757:Command 'Start' timed out waiting for response from the resource 'ora.cssd'. Details at (:CRSPE00111:) in /u01/app/11.2.0/grid/log/ol5-112-rac2/ohasd/ohasd.log.
2015-03-13 16:38:24.264
[ohasd(3315)]CRS-2765:Resource 'ora.cssdmonitor' has failed on server 'ol5-112-rac2'.
2015-03-13 16:38:35.915
[cssd(4326)]CRS-1713:CSSD daemon is started in clustered mode
2015-03-13 16:38:41.195
[cssd(4326)]CRS-1707:Lease acquisition for node ol5-112-rac2 number 2 completed
2015-03-13 16:38:41.259
[cssd(4326)]CRS-1605:CSSD voting file is online: /dev/oracleasm/disks/DISK1; details in /u01/app/11.2.0/grid/log/ol5-112-rac2/cssd/ocssd.log.
2015-03-13 16:38:41.562
[crsd(4285)]CRS-1013:The OCR location in an ASM disk group is inaccessible. Details in /u01/app/11.2.0/grid/log/ol5-112-rac2/crsd/crsd.log.
2015-03-13 16:38:42.217
[ohasd(3315)]CRS-2765:Resource 'ora.crsd' has failed on server 'ol5-112-rac2'.
2015-03-13 16:38:43.313
[crsd(4357)]CRS-1013:The OCR location in an ASM disk group is inaccessible. Details in /u01/app/11.2.0/grid/log/ol5-112-rac2/crsd/crsd.log.
2015-03-13 16:38:44.262
[ohasd(3315)]CRS-2765:Resource 'ora.crsd' has failed on server 'ol5-112-rac2'.
2015-03-13 16:38:44.716
[ohasd(3315)]CRS-2765:Resource 'ora.diskmon' has failed on server 'ol5-112-rac2'.
crsd log
2015-03-13 16:39:02.140: [ OCRASM][1266976496]proprasmo: kgfoCheckMount returned [7]
2015-03-13 16:39:02.140: [ OCRASM][1266976496]proprasmo: The ASM instance is down
2015-03-13 16:39:02.140: [ OCRRAW][1266976496]proprioo: Failed to open [+DATA]. Returned proprasmo() with [26]. Marking location as UNAVAILABLE.
2015-03-13 16:39:02.140: [ OCRRAW][1266976496]proprioo: No OCR/OLR devices are usable
2015-03-13 16:39:02.140: [ OCRASM][1266976496]proprasmcl: asmhandle is NULL
2015-03-13 16:39:02.140: [ OCRRAW][1266976496]proprinit: Could not open raw device
2015-03-13 16:39:02.140: [ OCRASM][1266976496]proprasmcl: asmhandle is NULL
2015-03-13 16:39:02.140: [ OCRAPI][1266976496]a_init:16!: Backend init unsuccessful : [26]
2015-03-13 16:39:02.140: [ CRSOCR][1266976496] OCR context init failure. Error: PROC-26: Error while accessing the physical storage ASM error [SLOS: cat=7, opn=kgfoAl06, dep=15077, loc=kgfokge
ORA-15077: could not locate ASM instance serving a required diskgroup
] [7]
2015-03-13 16:39:02.140: [    CRSD][1266976496][PANIC] CRSD exiting: Could not init OCR, code: 26
2015-03-13 16:39:02.140: [    CRSD][1266976496] Done
Pls help

Hi Levi,
I got below output from cssd.log
2015-03-15 10:38:48.248: [ GIPCNET][1214789952]gipcmodNetworkProcessConnect: slos op : sgipcnTcpConnect
2015-03-15 10:38:48.248: [ GIPCNET][1214789952]gipcmodNetworkProcessConnect: slos dep : No route to host (113)
2015-03-15 10:38:48.248: [ GIPCNET][1214789952]gipcmodNetworkProcessConnect: slos loc : connect
2015-03-15 10:38:48.248: [ GIPCNET][1214789952]gipcmodNetworkProcessConnect: slos info: addr '192.168.1.101:42729'
2015-03-15 10:38:48.248: [    CSSD][1214789952]clssscSelect: conn complete ctx 0x24d7aa0 endp 0x10d4
2015-03-15 10:38:48.248: [    CSSD][1214789952]clssnmeventhndlr: node(1), endp(0x10d4) failed, probe((nil)) ninf->endp (0x1000010d4) CONNCOMPLETE
2015-03-15 10:38:48.248: [    CSSD][1214789952]clssnmDiscHelper: ol5-112-rac1, node(1) connection failed, endp (0x10d4), probe(0x100000000), ninf->endp 0x10d4
2015-03-15 10:38:48.248: [    CSSD][1214789952]clssnmDiscHelper: node 1 clean up, endp (0x10d4), init state 0, cur state 0
2015-03-15 10:38:48.248: [GIPCXCPT][1214789952]gipcInternalDissociate: obj 0x27c8050 [00000000000010d4] { gipcEndpoint : localAddr 'gipc://ol5-112-rac2:de93-de83-5e0c-a373#192.168.1.102#50439', remoteAddr 'gipc://ol5-112-rac1:nm_ol5-112-scan#192.168.1.101#42729', numPend 0, numReady 0, numDone 0, numDead 0, numTransfer 0, objFlags 0x0, pidPeer 0, flags 0x8061a, usrFlags 0x0 } not associated with any container, ret gipcretFail (1)
2015-03-15 10:38:48.248: [GIPCXCPT][1214789952]gipcDissociateF [clssnmDiscHelper : clssnm.c : 3215]: EXCEPTION[ ret gipcretFail (1) ] failed to dissociate obj 0x27c8050 [00000000000010d4] { gipcEndpoint : localAddr 'gipc://ol5-112-rac2:de93-de83-5e0c-a373#192.168.1.102#50439', remoteAddr 'gipc://ol5-112-rac1:nm_ol5-112-scan#192.168.1.101#42729', numPend 0, numReady 0, numDone 0, numDead 0, numTransfer 0, objFlags 0x0, pidPeer 0, flags 0x8061a, usrFlags 0x0 }, flags 0x0
2015-03-15 10:38:48.248: [    CSSD][1214789952]clssnmDiscEndp: gipcDestroy 0x10d4
2015-03-15 10:38:48.414: [    CSSD][1147648320]clssnmvDHBValidateNCopy: node 1, ol5-112-rac1, has a disk HB, but no network HB, DHB has rcfg 320087493, wrtcnt, 207342, LATS 355744, lastSeqNo 207342, uniqueness 1426244111, timestamp 1426396128/31164744
2015-03-15 10:38:48.414: [    CSSD][1214789952]clssnmconnect: connecting to addr gipc://ol5-112-rac1:nm_ol5-112-scan#192.168.1.101#42729
2015-03-15 10:38:48.414: [    CSSD][1214789952]clssscConnect: endp 0x10e0 - cookie 0x24d7aa0 - addr gipc://ol5-112-rac1:nm_ol5-112-scan#192.168.1.101#42729
2015-03-15 10:38:48.414: [    CSSD][1214789952]clssnmconnect: connecting to node(1), endp(0x10e0), flags 0x10002
2015-03-15 10:38:48.710: [    CSSD][1181219136]clssgmWaitOnEventValue: after CmInfo State val 3, eval 1 waited 0
2015-03-15 10:38:49.209: [    CSSD][1206397248]clssnmRcfgMgrThread: Local Join
2015-03-15 10:38:49.209: [    CSSD][1206397248]clssnmLocalJoinEvent: begin on node(2), waittime 193000
2015-03-15 10:38:49.209: [    CSSD][1206397248]clssnmLocalJoinEvent: set curtime (356544) for my node
2015-03-15 10:38:49.209: [    CSSD][1206397248]clssnmLocalJoinEvent: scanning 32 nodes
2015-03-15 10:38:49.209: [    CSSD][1206397248]clssnmLocalJoinEvent: Node ol5-112-rac1, number 1, is in an existing cluster with disk state 3
2015-03-15 10:38:49.210: [    CSSD][1206397248]clssnmLocalJoinEvent: takeover aborted due to cluster member node found on disk
Thanks,
Suranga

I can not communicate with the FP-1000, using the serial port.

FP-100 communication by serial port.
My problem is the communication with the interface FP-1000, I haven been using it for two month with my program application and suddenly it stopped to work. I tried to use the FieldPoint Explorer to communicate using its last configuration but it does not work. I have tried to configure again and the FieldPoint Explorer doe not find any module, also I have seen that the network and access LEDs don lit when I am trying to communicate with the FP-1000.
I have checked all connection and they are already, the FP-1000 turn on, and the status LEDs does not lit.
I guess the trouble is the RS-323 connector at the FP-1000.
Could you tell how can I solve this problem?

Hello,
There are a number of things that you can try when you are experiencing communication problems with a FP-1000.
First, double-check that the serial port that you are using is the same one that you are specifying in FieldPoint Explorer. Try using another serial port on the host computer. Try connecting the FP-1000 to another computer.
Make sure that you have FieldPoint Explorer version 3.0.2 or later. Free upgrades are available from the web.
I hope this helps,
Chad Evans

ASM instance on one node can not startup

use dbca create database failure
[oracle@rac1 ~]$ dbca -silent -responseFile /home/oracle/dbca.rsp
Look at the log file "/opt/ora/product/10.2.0/db_1/cfgtoollogs/dbca/mydb.log" for further details.
[oracle@rac1 ~]$ cat "/opt/ora/product/10.2.0/db_1/cfgtoollogs/dbca/mydb.log"
PRKS-1009 : Failed to start ASM instance "+ASM2" on node "rac2", [CRS-0215: Could not start resource 'ora.rac2.ASM2.asm'.]
ORA-03135: connection lost contact
[oracle@rac2 bin]$ ./crs_stat -t
Name           Type           Target    State     Host
ora....SM1.asm application    ONLINE    ONLINE    rac1
ora....C1.lsnr application    ONLINE    ONLINE    rac1
ora.rac1.gsd   application    ONLINE    ONLINE    rac1
ora.rac1.ons   application    ONLINE    ONLINE    rac1
ora.rac1.vip   application    ONLINE    ONLINE    rac1
ora....SM2.asm application    ONLINE    OFFLINE
ora....C2.lsnr application    ONLINE    ONLINE    rac2
ora.rac2.gsd   application    ONLINE    ONLINE    rac2
ora.rac2.ons   application    ONLINE    ONLINE    rac2
ora.rac2.vip   application    ONLINE    ONLINE    rac2so i try to start asm instance on rac2
[oracle@rac2 bin]$ ./srvctl start asm -n rac2
PRKS-1009 : Failed to start ASM instance "+ASM2" on node "rac2", [PRKS-1009 : Failed to start ASM instance "+ASM2" on node "rac2", [rac2:ora.rac2.ASM2.asm:
rac2:ora.rac2.ASM2.asm:SQL*Plus: Release 10.2.0.1.0 - Production on Mon Jul 25 17:58:21 2011
rac2:ora.rac2.ASM2.asm:
rac2:ora.rac2.ASM2.asm:Copyright (c) 1982, 2005, Oracle. All rights reserved.
rac2:ora.rac2.ASM2.asm:
rac2:ora.rac2.ASM2.asm:Enter user-name: Connected to an idle instance.
rac2:ora.rac2.ASM2.asm:
rac2:ora.rac2.ASM2.asm:SQL> ORA-03113: end-of-file on communication channel
rac2:ora.rac2.ASM2.asm:SQL> Disconnected
rac2:ora.rac2.ASM2.asm:
CRS-0215: Could not start resource 'ora.rac2.ASM2.asm'.]]
[PRKS-1009 : Failed to start ASM instance "+ASM2" on node "rac2", [rac2:ora.rac2.ASM2.asm:
rac2:ora.rac2.ASM2.asm:SQL*Plus: Release 10.2.0.1.0 - Production on Mon Jul 25 17:58:21 2011
rac2:ora.rac2.ASM2.asm:
rac2:ora.rac2.ASM2.asm:Copyright (c) 1982, 2005, Oracle. All rights reserved.
rac2:ora.rac2.ASM2.asm:
rac2:ora.rac2.ASM2.asm:Enter user-name: Connected to an idle instance.
rac2:ora.rac2.ASM2.asm:
rac2:ora.rac2.ASM2.asm:SQL> ORA-03113: end-of-file on communication channel
rac2:ora.rac2.ASM2.asm:SQL> Disconnected
rac2:ora.rac2.ASM2.asm:check the alert log find
Mon Jul 25 17:58:23 2011
Maximum Tranmission Unit (mtu) of the ether adapter is different
on the node running instance 1, and this node.
Ether adapters connecting the cluster nodes must be configured
with identical mtu on all the nodes, for Oracle.
Please ensure the mtu attribute of the ether adapter on all
nodes are identical, before running Oracle.
Mon Jul 25 17:58:23 2011
Errors in file /opt/ora/admin/+ASM/bdump/+asm2_lmon_29711.trc:
ORA-27550: Target ID protocol check failed. tid vers=%d, type=%d, remote instance number=%d, local instance number=%d
LMON: terminating instance due to error 27550
Mon Jul 25 17:58:25 2011
Shutting down instance (abort)
License high water mark = 0
Mon Jul 25 17:58:28 2011
Instance terminated by LMON, pid = 29711
Mon Jul 25 17:58:30 2011
Instance terminated by USER, pid = 29831and i checked my eth
[root@rac1 oracle]# ifconfig -a
eth0      Link encap:Ethernet HWaddr 00:0C:29:3C:42:0C
          inet addr:192.168.40.102 Bcast:192.168.40.255 Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:9762 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6028 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:1193646 (1.1 MiB) TX bytes:1037252 (1012.9 KiB)
          Interrupt:67 Base address:0x2400
eth0:1    Link encap:Ethernet HWaddr 00:0C:29:3C:42:0C
          inet addr:192.168.40.201 Bcast:192.168.40.255 Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          Interrupt:67 Base address:0x2400
eth1      Link encap:Ethernet HWaddr 00:0C:29:3C:42:16
          inet addr:10.10.17.221 Bcast:10.10.17.225 Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:30185 errors:0 dropped:0 overruns:0 frame:0
          TX packets:37936 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:19988844 (19.0 MiB) TX bytes:35126056 (33.4 MiB)
          Interrupt:51 Base address:0x2480
lo        Link encap:Local Loopback
          inet addr:127.0.0.1 Mask:255.0.0.0
          UP LOOPBACK RUNNING MTU:16436 Metric:1
          RX packets:52537 errors:0 dropped:0 overruns:0 frame:0
          TX packets:52537 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:4380651 (4.1 MiB) TX bytes:4380651 (4.1 MiB)
[root@rac2 ~]# ifconfig -a
eth0      Link encap:Ethernet HWaddr 00:0C:29:9C:CC:90
          inet addr:192.168.40.103 Bcast:192.168.40.255 Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:3665 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1489 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:563952 (550.7 KiB) TX bytes:243127 (237.4 KiB)
          Interrupt:67 Base address:0x2400
eth0:1    Link encap:Ethernet HWaddr 00:0C:29:9C:CC:90
          inet addr:192.168.40.202 Bcast:192.168.40.255 Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          Interrupt:67 Base address:0x2400
eth1      Link encap:Ethernet HWaddr 00:0C:29:9C:CC:9A
          inet addr:10.10.17.222 Bcast:10.10.17.225 Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:38281 errors:0 dropped:0 overruns:0 frame:0
          TX packets:29683 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:35182270 (33.5 MiB) TX bytes:19905266 (18.9 MiB)
          Interrupt:51 Base address:0x2480
lo        Link encap:Local Loopback
          inet addr:127.0.0.1 Mask:255.0.0.0
          UP LOOPBACK RUNNING MTU:16436 Metric:1
          RX packets:44387 errors:0 dropped:0 overruns:0 frame:0
          TX packets:44387 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:2299383 (2.1 MiB) TX bytes:2299383 (2.1 MiB)any idea ?
i try to run dbca on rac2 ,it seems OK
============
ASM instance still have problem,no ASM instance create in rac1
[oracle@rac2 bin]$ ./crs_stat -t
Name           Type           Target    State     Host
ora.mydb.db    application    ONLINE    ONLINE    rac1
ora....b1.inst application    ONLINE    OFFLINE
ora....b2.inst application    ONLINE    ONLINE    rac2
ora....SM1.asm application    ONLINE    OFFLINE
ora....C1.lsnr application    ONLINE    ONLINE    rac1
ora....C2.lsnr application    ONLINE    OFFLINE              => ora.rac1.LISTENER_RAC2.lsnr   (i do not know where this resource come from ??)
ora.rac1.gsd   application    ONLINE    ONLINE    rac1
ora.rac1.ons   application    ONLINE    ONLINE    rac1
ora.rac1.vip   application    ONLINE    ONLINE    rac1
ora....SM2.asm application    ONLINE    ONLINE    rac2
ora....C2.lsnr application    ONLINE    ONLINE    rac2
ora.rac2.gsd   application    ONLINE    ONLINE    rac2
ora.rac2.ons   application    ONLINE    ONLINE    rac2
ora.rac2.vip   application    ONLINE    ONLINE    rac2and here is my dbca.rsp file content
[GENERAL]
RESPONSEFILE_VERSION = "10.0.0"
OPERATION_TYPE = "createDatabase"
[CREATEDATABASE]
GDBNAME = "mydb.us.oracle.com"
SID = "mydb"
NODELIST=rac1,rac2
TEMPLATENAME = "/home/oracle/mydb.dbc"
SYSPASSWORD = "Myss123456"
SYSTEMPASSWORD = "Myss123456"
EMCONFIGURATION = "NONE"
DBSNMPPASSWORD = "Myss123456"
STORAGETYPE=ASM
DISKLIST=/dev/oracleasm/disks/VOL1,/dev/oracleasm/disks/VOL2
DISKGROUPNAME=ORADG
REDUNDANCY=EXTRENAL
DISKSTRING="/dev/oracleasm/disks/*"
ASM_SYS_PASSWORD="Myss123456"
LISTENERS = "listener1 listener2"Edited by: 859340 on 2011-7-24 下午7:23
Edited by: 859340 on 2011-7-24 下午7:32
Edited by: 859340 on 2011-7-24 下午7:35
Edited by: 859340 on 2011-7-24 下午7:51

Hi,
Use this tech note on MOS.
*Instance Crash on startup with ORA-27550: Target ID protocol check failed [ID 730516.1]*
Regards,
Levi Pereira

Why my TDS2014B scope can not communicate with signalexpress

I have already installed LabView 2014,Signal express and VISA 4.6.
Now i want my TDS2014 scope communicate with Signal Express,
of course,I haved installed TDS2014's driver,it's a zip file,and extracted directly to the \instr.lib directory.
but when i Create New IVI Session，I found anything in instrument driver box,while Resource Descriptor can be selected as my "usb USB0::0x0699:....."
what should I do ?any suggestions?
PLEASE help and contact me,thanks.

Thanks Dennis.
I made it.You are right,I installed the wrong driver,but now new problems occured.When i clik run,erro shows "Primary Error: (Hex 0xBFFA0010) Invalid value for parameter or property.
Secondary Error: (Hex 0xBFFC0004) Parameter 4 out of range, or error occurred while setting Parameter 4.
Elaboration: Max Input Frequency"
AM I havn't configured the parameter yet?I tried to set IVI configuration in Measurement & Automation Explore,but it still can't work.

IChat AIM Can Not Communicate

I have read many different variations of this problem on this site but none of them have fixed my problem.
I have a IMAC 24" Core 2 Duo w/2MB, MAC OS X 10.5.1. My daughter has a Dell Laptop running Vista with AIM 6 loaded. We both have AIM screen names and we both in the same LAN using Cox Internet through my Netgear Router.
When she initiates a Video call (Dell computer) I get the invitation (IMAC) and accept it. However; the Dell register a timeout on the response. When I initiate the Video call (IMAC) and she accepts it I get an error message that asks me to send to the error Apple.
I have played with the settings in both IChat and Quicktime on the IMAC and AIM on the Dell with no luck. Can I get a straight forward answer/fix for this problem on this site?

I recently had a breakthrough success with getting video to work. Previously it has worked only sporadically. I had success & failure at home & work, on & off VPN. All my accounts, jabber, google & aim, were intermittent. Rebooting sometimes allowed a video connection to start working.
Yesterday, I changed Preferences | Audio/Video | Bandwidth Limit from none to 500k. My contact did the same. We were immediately able to establish a video conference.
We then, one at a time, bumped Bandwidth Limit back to None & were able to successfully establish a video conference each time.
Interestingly, the day before, we were able to get 3 macs working from 2 locations, but the 4th mac would not connect. The next day, none of the macs could connect. That's when we tried changing the Bandwidth Limit.
I seem to vaguely recall that SIP negotiations generally start out with the maximum media capabilities available, then negotiate downward if necessary. I wonder if adding the bandwidth limit pulls the negotiation within 'acceptable limits'? It's been a few years since I talked about SIP, so feel free to reply with technical corrections!
Haven't had a chance to replicate this, so ymmv.
Good luck!

MQ 2 FILE scenrio - can not communicate with communication channel

hello
trying to run MQ 2 file and the file is in the MQ and the communication channel of the sender write me in the RWB this message
XI inbound processing failed for message at 2008-04-15. JMS and XI identfers for message are ID:.......
JMS adapter will rollback database and JMS session tranactions.
does any one know what is the problem with the Queue? why does the sender does not recieve the message and I dont see it in SXMB moni?

Seube wrote:
mmm it seems I spoke too quickly, things seems to work as expected now. I don't know what I did change since.
I've retested between two cards: it seems also ok except 2 strange things:
- when CAN2 is physically connected on PC2, it seems CAN1 that listens instead (as if CAN1 was connected)
- trames sent from CAN0 and CAN1 on PC1 seems to be repeated from IXXAT card: they are returning respectively on CAN1 and CAN0.
Sorry, no idea on these two. As for the first one, what happens if you connect CAN1 to CAN2 on PC2 (no connetion to PC1)? I don't know anything about the IXXAT card. Is there some switch that internally bridges the two ports?

I can not communicate on facetime

Excuse me , I use to call by facetime everyday from my iphone to another iphone.
I m living in Mexico , and the another one is in England.
I cant stablish communication along this day, i haced tried but i cant.
The message that appears in the viewer is : connecting ,,, and we were waiting for that, and it cant be posible.
Please I need your help, what we can do for fixing the problem and chating by facetime like always .
Thank you very much for your kind help,
Regards sincerly
Adriana Miranda

First things I would try is:
Reboot- Hold the home button and power button at the same time until the screen goes black and the apple logo appears. Try again
Sign out and back in on facetime in Settings>Facetime.
Lastly it could be on Apple's end.http://www.apple.com/support/systemstatus/
I would say restore phone, but your saying it has worked before. Check your home internet connection(reset your router etc) if you need to. Check that by opening up a webpage etc.. to see if its your wifi.

RACs nodes can not communicate

Similar Messages

Maybe you are looking for