RADIUS Server on Mac OS X Server 10.5 Leopard
I must set up a Radius Server on my LAN and WLAN, I will do this with Mac OS X Server v.10.5 Leopard but I don't know if it's compatible with any routers(for LAN and WLAN Access) and with Windows XP Pro SP3 computers.
Can anyone help me????
I know this question is fairly old but I can now state that as of last night I am using a Netgear WN802T - 200 access point paired with the RADIUS service on a Leopard Server.
Leave the "type" of station either blank or other for Netgear.
Accounting does not seem to work and throws errors in the radiusd log, but other than that the Mac clients and iPhones show a WPA2 Enterprise connection.
Your mileage may vary.
Similar Messages
-
RADIUS Capabilities in Mac OS X Server (10.6 specifically)
We are building a WiFi Network to support 100 users. Our building is about a city block by a half a city block, so we will be using a lot of Airports (Airport Extreme 802.11n dual). Since we are concerned about security, we will be using Mac OS X Server's (10.6) Radius server.
Can anyone tell me if it is possible to record logs of user1 when to siteX at this date and time? I am concerned that if something bad goes down, we can track who did what & when.
Any info on this is appreciated.If you enable the extended logging using the following commands you will get all the details you are after in the radius log.
$ sudo radiusconfig -setconfig log_auth yes
$ sudo radiusconfig -setconfig logauthgoodpass yes
$ sudo radiusconfig -setconfig logauthbadpass yes
In the log you will then see entries like this
Auth: Login OK: [002500xxxxxx/password] (from client Airport BaseStation port 0 cli 00-25-00-xx-xx-xx)
where 'Airport BaseStation' will be the name of your access point as defined in the RADIUS server admin section.
Charlie at ewhizz d0t net
ewhizz dot net -
How to configure a Cisco 3560 with MAC-based 802.1x authentication by radius server
Hi dearI
How can I configure a Cisco 3560 to authenticate a client based on its mac address with 802.1x and radius server. Many tanks in advance!Olivier,
You can't reference WLP visitor roles in weblogic.xml, but you can
reference global roles (created using the WLS console):
- <security-role-assignment>
<role-name>PortalSystemAdministrator</role-name>
<externally-defined />
</security-role-assignment>
-Phil
"Olivier" <[email protected]> wrote in message
news:[email protected]..
>
We need to have login page to our portal app.
When using "form based" authentication is it possible to map the securityon a
"entitlement role" ?
Our need is to be abled to give direct url acces to some pages of theportal (for
exemple by sending urls like"http://server/appcontextpath/appmanager/myportal/mydesktop?_nfpb=true&_page
Label=mypage")"
by email to portal users) and need a simple mecanism of authenticationbefore
redirecting to the portal page.
Inste -
Can't authenticate Mac VPN client from RADIUS server
Hello,
I'm a real noob here so please bear with me.
I have been able to configure my PIX 515E to allow VPN connections onto my network, but what I need to do is set up some sort of user authentication to control access at a user level. From what I've read here and in the Configuration Guide I should be able to do this authentication with a RADIUS server. I'm running a Corriente Networks Elektron Security server which has RADIUS server capabilities. It is running on my (inside) interface at IP 192.168.10.26.
I thought that I had everything configured properly but it never seems to authenticate. I connect, the XAUTH window pops up, I add my username and password as it's configured on my RADIUS server, but when I click OK it just cycles the progress bar at the bottom and eventually times out. The client log doesn't show me anything and the log on the RADIUS server shows me nothing. Any ideas? this seems like it should be simple because I can connect until I attempt to authenticate to the RADIUS server.
TIA for any direction you can provide me.
ChristineIf it helps, here is my config with a some of the non-related bits deleted:
interface ethernet0 auto
interface ethernet1 auto
interface ethernet2 auto
nameif ethernet0 outside security0
nameif ethernet1 inside security100
nameif ethernet2 DMZ security50
enable password ********* encrypted
passwd ******* encrypted
hostname pixfirewall
domain-name acme.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol http 80
fixup protocol http 82
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
access-list inside_outbound_nat0_acl permit ip any 192.168.10.0 255.255.255.0
access-list inside_outbound_nat0_acl permit ip host 192.168.10.26 192.168.10.192 255.255.255.224
access-list inside_outbound_nat0_acl permit ip host 192.168.10.69 192.168.10.192 255.255.255.224
access-list outside_cryptomap_dyn_20 permit ip any 192.168.10.0 255.255.255.0
access-list outside_cryptomap_dyn_40 permit ip any 192.168.10.192 255.255.255.224
mtu outside 1500
mtu inside 1500
mtu DMZ 1500
ip address outside 207.XXX.XXX.130 255.255.255.0
ip address inside 192.168.10.1 255.255.255.0
ip address DMZ 192.168.100.1 255.255.255.0
multicast interface inside
ip audit info action alarm
ip audit attack action alarm
ip local pool CBI_VPN_Pool 192.168.10.201-192.168.10.220
pdm location 192.168.10.50 255.255.255.255 inside
pdm group CBI_Servers inside
pdm logging warnings 100
pdm history enable
arp timeout 14400
global (outside) 200 interface
global (DMZ) 200 interface
nat (inside) 0 access-list inside_outbound_nat0_acl
nat (inside) 200 192.168.10.0 255.255.255.0 0 0
static (inside,outside) 207.XXX.XXX.150 192.168.10.27 netmask 255.255.255.255 0 0
static (inside,outside) 207.XXX.XXX.132 192.168.10.26 dns netmask 255.255.255.255 0 0
access-group 100 in interface outside
route outside 0.0.0.0 0.0.0.0 207.XXX.XXX.129 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server radius-authport 1812
aaa-server radius-acctport 1812
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server RADIUS (inside) host 192.168.10.26 ************* timeout 10
aaa-server LOCAL protocol local
http server enable
http 192.168.10.3 255.255.255.255 inside
no floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-DES-MD5
crypto dynamic-map outside_dyn_map 40 match address outside_cryptomap_dyn_40
crypto dynamic-map outside_dyn_map 40 set transform-set ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map client authentication RADIUS
crypto map outside_map interface outside
crypto map inside_map interface inside
isakmp enable outside
isakmp nat-traversal 3600
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
vpngroup Test_VPN address-pool CBI_VPN_Pool
vpngroup Test_VPN dns-server 142.77.2.101 142.77.2.36
vpngroup Test_VPN default-domain acme.com
vpngroup Test_VPN idle-time 1800
vpngroup Test_VPN authentication-server RADIUS
vpngroup Test_VPN user-authentication
vpngroup Test_VPN user-idle-timeout 1200
vpngroup Test_VPN password ********
ssh timeout 5
console timeout 0
dhcpd address 192.168.10.100-192.168.10.254 inside
dhcpd dns 142.77.2.101 142.77.2.36
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
dhcpd enable inside -
EAP-FAST on Local Radius Server : Can't Get It Working
Hi all
I'm using an 877w router (flash:c870-advsecurityk9-mz.124-24.T4.bin) as local radius server and have followed various config guides on CCO. LEAP works fine but I just can't get EAP-FAST to work.
I'm testing with win7 client using anyconnect secure mobility client, and also a mac book pro but without luck.
the router sees unknown auth type, and when I run some debugs it talks of unknown eap type 3
sh radius local-server s
Successes : 1 Unknown usernames : 0
Client blocks : 0 Invalid passwords : 0
Unknown NAS : 0 Invalid packet from NAS: 17
NAS : 172.27.44.1
Successes : 1 Unknown usernames : 0
Client blocks : 0 Invalid passwords : 0
Corrupted packet : 0 Unknown RADIUS message : 0
No username attribute : 0 Missing auth attribute : 0
Shared key mismatch : 0 Invalid state attribute: 0
Unknown EAP message : 0 Unknown EAP auth type : 17
Auto provision success : 0 Auto provision failure : 0
PAC refresh : 0 Invalid PAC received : 0
Can anyone suggest what I might be doing wrong?
Regs, TimThanks Nicolas, relevant snippets from config:
aaa new-model
aaa group server radius rad_eap
server 172.27.44.1 auth-port 1812 acct-port 1813
aaa authentication login eap_methods group rad_eap
aaa authorization exec default local
aaa session-id common
dot11 ssid home
vlan 3
authentication open eap eap_methods
authentication network-eap eap_methods
authentication key-management wpa
ip dhcp pool home
import all
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 194.74.65.68 194.74.65.69
ip inspect name ethernetin tcp
ip inspect name ethernetin udp
ip inspect name ethernetin pop3
ip inspect name ethernetin ssh
ip inspect name ethernetin dns
ip inspect name ethernetin ftp
ip inspect name ethernetin tftp
ip inspect name ethernetin smtp
ip inspect name ethernetin icmp
ip inspect name ethernetin telnet
interface Dot11Radio0
no ip address
encryption vlan 1 mode ciphers aes-ccm tkip
encryption vlan 2 mode ciphers aes-ccm tkip
encryption vlan 3 mode ciphers aes-ccm tkip
broadcast-key vlan 1 change 30
broadcast-key vlan 2 change 30
broadcast-key vlan 3 change 30
ssid home
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
interface Dot11Radio0.3
encapsulation dot1Q 3
no cdp enable
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 spanning-disabled
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
interface Vlan3
no ip address
bridge-group 3
interface BVI3
ip address 192.168.1.1 255.255.255.0
ip inspect ethernetin in
ip nat inside
ip virtual-reassembly
radius-server local
no authentication mac
nas 172.27.44.1 key 0 123456
user test1 nthash 0 B151E8FF684B4F376C018E632A247D84
user test2 nthash 0 F2EEAE1D895645B819C9FD217D0CA1F9
user test3 nthash 0 0CB6948805F797BF2A82807973B89537
radius-server host 172.27.44.1 auth-port 1812 acct-port 1813 key 123456
radius-server vsa send accounting -
Cisco 871w, radius server local, and leap or eap-fast will not authenticate
Hello, i trying to setup eap-fast or leap on my 871w. i belive i have it confiured correctly but i can not get any device to authenticate to router. Below is the confiureation that i being used. any help would be welcome!
! Last configuration change at 15:51:30 AZT Wed Jan 4 2012 by testtest
! NVRAM config last updated at 15:59:37 AZT Wed Jan 4 2012 by testtest
version 12.4
configuration mode exclusive auto
service nagle
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service linenumber
service pt-vty-logging
service sequence-numbers
hostname router871
boot-start-marker
boot-end-marker
logging count
logging message-counter syslog
logging buffered 4096
logging rate-limit 512 except critical
logging console critical
enable secret 5 <omitted>
aaa new-model
aaa group server radius rad-test3
server 192.168.16.49 auth-port 1812 acct-port 1813
aaa authentication login default local
aaa authentication login eap-methods group rad-test3
aaa authorization exec default local
aaa session-id common
clock timezone AZT -7
clock save interval 8
dot11 syslog
dot11 ssid test2
vlan 2
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 <omitted>
dot11 ssid test1
vlan 1
authentication open
authentication key-management wpa
wpa-psk ascii 7 <omitted>
dot11 ssid test3
vlan 3
authentication open eap eap-methods
authentication network-eap eap-methods
no ip source-route
no ip gratuitous-arps
ip options drop
ip dhcp bootp ignore
ip dhcp excluded-address 192.162.16.49 192.162.16.51
ip dhcp excluded-address 192.168.16.33
ip dhcp excluded-address 192.168.16.1 192.168.16.4
ip dhcp pool vlan1pool
import all
network 192.168.16.0 255.255.255.224
default-router 192.168.16.1
domain-name test1.local.home
lease 4
ip dhcp pool vlan2pool
import all
network 192.168.16.32 255.255.255.240
default-router 192.168.16.33
domain-name test2.local.home
lease 0 6
ip dhcp pool vlan3pool
import all
network 192.168.16.48 255.255.255.240
default-router 192.168.16.49
domain-name test3.local.home
lease 2
ip cef
ip inspect alert-off
ip inspect max-incomplete low 25
ip inspect max-incomplete high 50
ip inspect one-minute low 25
ip inspect one-minute high 50
ip inspect udp idle-time 15
ip inspect tcp idle-time 1800
ip inspect tcp finwait-time 30
ip inspect tcp synwait-time 60
ip inspect tcp block-non-session
ip inspect tcp max-incomplete host 25 block-time 2
ip inspect name firewall tcp router-traffic
ip inspect name firewall ntp
ip inspect name firewall ftp
ip inspect name firewall udp router-traffic
ip inspect name firewall pop3
ip inspect name firewall pop3s
ip inspect name firewall imap
ip inspect name firewall imap3
ip inspect name firewall imaps
ip inspect name firewall smtp
ip inspect name firewall ssh
ip inspect name firewall icmp router-traffic timeout 10
ip inspect name firewall dns
ip inspect name firewall h323
ip inspect name firewall hsrp
ip inspect name firewall telnet
ip inspect name firewall tftp
no ip bootp server
no ip domain lookup
ip domain name local.home
ip name-server 8.8.8.8
ip name-server 8.8.4.4
ip accounting-threshold 100
ip accounting-list 192.168.16.0 0.0.0.31
ip accounting-list 192.168.16.32 0.0.0.15
ip accounting-list 192.168.16.48 0.0.0.15
ip accounting-transits 25
login block-for 120 attempts 5 within 60
login delay 5
login on-failure log
memory free low-watermark processor 65536
memory free low-watermark IO 16384
username testtest password 7 <omitted>
archive
log config
logging enable
logging size 255
notify syslog contenttype plaintext
hidekeys
path tftp://<omitted>/archive-config
write-memory
ip tcp synwait-time 10
ip ssh time-out 20
ip ssh authentication-retries 2
ip ssh logging events
ip ssh version 2
bridge irb
interface Loopback0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
interface Null0
no ip unreachables
interface FastEthernet0
switchport mode trunk
shutdown
interface FastEthernet1
switchport mode trunk
shutdown
interface FastEthernet2
shutdown
spanning-tree portfast
interface FastEthernet3
spanning-tree portfast
interface FastEthernet4
description Cox Internet Connection
ip address dhcp
ip access-group ingress-filter in
ip access-group egress-filter out
no ip redirects
no ip unreachables
no ip proxy-arp
ip accounting access-violations
ip flow ingress
ip flow egress
ip inspect firewall out
ip nat outside
ip virtual-reassembly
ip tcp adjust-mss 1460
load-interval 30
duplex auto
speed auto
no cdp enable
interface Dot11Radio0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 2 mode ciphers aes-ccm
encryption key 1 size 128bit 7 <omitted> transmit-key
encryption mode wep mandatory
broadcast-key vlan 1 change <omitted> membership-termination
broadcast-key vlan 3 change <omitted> membership-termination
broadcast-key vlan 2 change <omitted> membership-termination
ssid test2
ssid test1
ssid test3
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
rts threshold 2312
no cdp enable
interface Dot11Radio0.1
description <omitted>
encapsulation dot1Q 1 native
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.2
description <omitted>
encapsulation dot1Q 2
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 spanning-disabled
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
interface Dot11Radio0.3
description <omitted>
encapsulation dot1Q 3
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 spanning-disabled
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
interface Vlan1
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan2
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 2
bridge-group 2 spanning-disabled
interface Vlan3
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 3
bridge-group 3 spanning-disabled
interface BVI1
description <omitted>
ip address 192.168.16.1 255.255.255.224
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
interface BVI2
description <omitted>
ip address 192.168.16.33 255.255.255.240
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
interface BVI3
description <omitted>
ip address 192.168.16.49 255.255.255.240
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
no ip http server
no ip http secure-server
ip http secure-ciphersuite 3des-ede-cbc-sha rc4-128-sha
ip http timeout-policy idle 5 life 43200 requests 5
ip flow-top-talkers
top 10
sort-by bytes
ip nat inside source list 1 interface FastEthernet4 overload
ip nat inside source static tcp 192.168.16.50 80 interface FastEthernet4 80
ip nat inside source static tcp 192.168.16.50 53 interface FastEthernet4 53
ip nat inside source static tcp 192.168.16.50 3074 interface FastEthernet4 3074
ip nat inside source static udp 192.168.16.50 3074 interface FastEthernet4 3074
ip nat inside source static udp 192.168.16.50 88 interface FastEthernet4 88
ip nat inside source static udp 192.168.16.50 53 interface FastEthernet4 53
ip access-list extended egress-filter
deny ip any host <omitted>
deny ip any host <omitted>
deny ip host <omitted> any
deny ip host <omitted> any
remark ----- Bogons Filter -----
deny ip 0.0.0.0 0.255.255.255 any
deny ip 10.0.0.0 0.10.9.255 any
deny ip 10.0.0.0 0.10.13.255 any
deny ip 127.0.0.0 0.255.255.255 any
deny ip 169.254.0.0 0.0.255.255 any
deny ip 172.16.0.0 0.15.255.255 any
deny ip 192.0.0.0 0.0.0.255 any
deny ip 192.0.2.0 0.0.0.255 any
deny ip 192.168.0.0 0.0.15.255 any
deny ip 192.168.0.0 0.0.255.255 any
deny ip 198.18.0.0 0.1.255.255 any
deny ip 198.51.100.0 0.0.0.255 any
deny ip 203.0.113.0 0.0.0.255 any
deny ip 224.0.0.0 31.255.255.255 any
remark ----- Internal networks -----
permit ip <omitted> 0.0.0.3 any
deny ip any any log
ip access-list extended ingress-filter
remark ----- To get IP form COX -----
permit udp any eq bootps any eq bootpc
deny icmp any any log
deny udp any any eq echo
deny udp any eq echo any
deny tcp any any fragments
deny udp any any fragments
deny ip any any fragments
deny ip any any option any-options
deny ip any any ttl lt 4
deny ip any host <omitted>
deny ip any host <omitted>
deny udp any any range 33400 34400
remark ----- Bogons Filter -----
deny ip 0.0.0.0 0.255.255.255 any
deny ip 10.0.0.0 0.255.255.255 any
deny ip 127.0.0.0 0.255.255.255 any
deny ip 169.254.0.0 0.0.255.255 any
deny ip 172.16.0.0 0.15.255.255 any
deny ip 192.0.0.0 0.0.0.255 any
deny ip 192.0.2.0 0.0.0.255 any
deny ip 192.168.0.0 0.0.255.255 any
deny ip 198.18.0.0 0.1.255.255 any
deny ip 198.51.100.0 0.0.0.255 any
deny ip 203.0.113.0 0.0.0.255 any
deny ip 224.0.0.0 31.255.255.255 any
remark ----- Internal networks -----
deny ip 10.10.10.0 0.0.0.255 any
deny ip 10.10.11.0 0.0.0.255 any
deny ip 10.10.12.0 0.0.0.255 any
deny ip any any log
access-list 1 permit 192.168.16.0 0.0.0.63
access-list 20 permit 127.127.1.1
access-list 20 permit 204.235.61.9
access-list 20 permit 173.201.38.85
access-list 20 permit 216.229.4.69
access-list 20 permit 152.2.21.1
access-list 20 permit 130.126.24.24
access-list 21 permit 192.168.16.0 0.0.0.63
radius-server local
no authentication mac
eapfast authority id <omitted>
eapfast authority info <omitted>
eapfast server-key primary 7 <omitted>
nas 192.168.16.49 key 7 <omitted>
group rad-test3
vlan 3
ssid test3
user test nthash 7 <omitted> group rad-test3
user testtest nthash 7 <omitted> group rad-test3
radius-server attribute 32 include-in-access-req format %h
radius-server host 192.168.16.49 auth-port 1812 acct-port 1813 key 7 <omitted>
radius-server vsa send accounting
control-plane host
control-plane transit
control-plane cef-exception
control-plane
bridge 1 protocol ieee
bridge 1 route ip
bridge 2 protocol ieee
bridge 2 route ip
bridge 3 protocol ieee
bridge 3 route ip
line con 0
password 7 <omitted>
logging synchronous
no modem enable
transport output telnet
line aux 0
password 7 <omitted>
logging synchronous
transport output telnet
line vty 0 4
password 7 <omitted>
logging synchronous
transport preferred ssh
transport input ssh
transport output ssh
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
process cpu threshold type total rising 80 interval 10 falling 40 interval 10
ntp authentication-key 1 md5 <omitted> 7
ntp authenticate
ntp trusted-key 1
ntp source FastEthernet4
ntp access-group peer 20
ntp access-group serve-only 21
ntp master 1
ntp server 152.2.21.1 maxpoll 4
ntp server 204.235.61.9 maxpoll 4
ntp server 130.126.24.24 maxpoll 4
ntp server 216.229.4.69 maxpoll 4
ntp server 173.201.38.85 maxpoll 4
endso this what i am getting now for debug? any thoughs?
010724: Jan 5 16:26:04.527 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/2
010725: Jan 5 16:26:08.976 AZT: RADIUS: No response from (162.168.16.49:1812,1813) for id 1645/2
010726: Jan 5 16:26:08.976 AZT: RADIUS/DECODE: No response from radius-server; parse response; FAIL
010727: Jan 5 16:26:08.976 AZT: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
010728: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAIL
010729: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response
010730: Jan 5 16:26:08.976 AZT: Client d8b3.7759.0488 failed: EAP reason 1
010731: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: Failed client d8b3.7759.0488 with aaa_req_status_detail 1
010732: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for d8b3.7759.0488
010733: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client d8b3.7759.0488
010734: Jan 5 16:26:08.976 AZT: EAPOL pak dump tx
010735: Jan 5 16:26:08.976 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0004
010736: Jan 5 16:26:08.976 AZT: EAP code: 0x4 id: 0x1 length: 0x0004
0AD05650: 01000004 04010004 ........
0AD05660:
010737: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: sending data to requestor status 1
010738: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010739: Jan 5 16:26:08.980 AZT: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds
010740: Jan 5 16:26:08.980 AZT: dot11_auth_dot1x_send_client_fail: Authentication failed for d8b3.7759.0488
010741: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: sending data to requestor status 0
010742: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: client FAILED to authenticate d8b3.7759.0488, node_type 64 for application 0x1
010743: Jan 5 16:26:08.980 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010744: Jan 5 16:26:08.984 AZT: %DOT11-7-AUTH_FAILED: Station d8b3.7759.0488 Authentication failed
010745: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010746: Jan 5 16:26:09.624 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010747: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: req->auth_type 0
010748: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010749: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010750: Jan 5 16:26:09.624 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010751: Jan 5 16:26:09.624 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010752: Jan 5 16:26:09.624 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010753: Jan 5 16:26:09.624 AZT: EAPOL pak dump tx
010754: Jan 5 16:26:09.624 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010755: Jan 5 16:26:09.624 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0AD05B50: 01000031 01010031 ...1...1
0AD05B60: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0AD05B70: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0AD05B80: 72383731 2C706F72 7469643D 30 r871,portid=0
010756: Jan 5 16:26:09.644 AZT: dot11_auth_send_msg: sending data to requestor status 1
010757: Jan 5 16:26:09.648 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010758: Jan 5 16:26:09.648 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010759: Jan 5 16:26:09.656 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010760: Jan 5 16:26:09.656 AZT: EAPOL pak dump rx
010761: Jan 5 16:26:09.656 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0009
010762: Jan 5 16:26:09.656 AZT: EAP code: 0x2 id: 0x1 length: 0x0009 type: 0x1
0B060D50: 01000009 02010009 ........
0B060D60: 01746573 74 .test
010763: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(CLIENT_WAIT,CLIENT_REPLY) for d8b3.7759.0488
010764: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_send_response_to_server: Sending client d8b3.7759.0488 data to server
010765: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_send_response_to_server: Started timer server_timeout 60 seconds
010766: Jan 5 16:26:09.664 AZT: RADIUS/ENCODE(00000198):Orig. component type = DOT11
010767: Jan 5 16:26:09.664 AZT: RADIUS: AAA Unsupported Attr: ssid [282] 8
010768: Jan 5 16:26:09.664 AZT: RADIUS: 74 6F 79 73 6F 6E [toyson]
010769: Jan 5 16:26:09.664 AZT: RADIUS: AAA Unsupported Attr: interface [175] 3
010770: Jan 5 16:26:09.664 AZT: RADIUS: 36 [6]
010771: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Config NAS IP: 192.168.16.49
010772: Jan 5 16:26:09.664 AZT: RADIUS/ENCODE(00000198): acct_session_id: 408
010773: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Config NAS IP: 192.168.16.49
010774: Jan 5 16:26:09.664 AZT: RADIUS(00000198): sending
010775: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Send Access-Request to 162.168.16.49:1645 id 1645/3, len 133
010776: Jan 5 16:26:09.664 AZT: RADIUS: authenticator BF 69 DD DF 89 1F C6 FB - EF EC 12 EB C5 3F 3A CD
010777: Jan 5 16:26:09.664 AZT: RADIUS: User-Name [1] 6 "test"
010778: Jan 5 16:26:09.664 AZT: RADIUS: Framed-MTU [12] 6 1400
010779: Jan 5 16:26:09.664 AZT: RADIUS: Called-Station-Id [30] 16 "0019.3075.e660"
010780: Jan 5 16:26:09.664 AZT: RADIUS: Calling-Station-Id [31] 16 "d8b3.7759.0488"
010781: Jan 5 16:26:09.668 AZT: RADIUS: Service-Type [6] 6 Login [1]
010782: Jan 5 16:26:09.668 AZT: RADIUS: Message-Authenticato[80] 18
010783: Jan 5 16:26:09.668 AZT: RADIUS: 5B FA 47 07 0E E3 4B 71 7F 60 6E 4E 91 37 84 A6 [[?G???Kq?`nN?7??]
010784: Jan 5 16:26:09.668 AZT: RADIUS: EAP-Message [79] 11
010785: Jan 5 16:26:09.668 AZT: RADIUS: 02 01 00 09 01 74 65 73 74 [?????test]
010786: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]
010787: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port [5] 6 661
010788: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port-Id [87] 5 "661"
010789: Jan 5 16:26:09.668 AZT: RADIUS: NAS-IP-Address [4] 6 192.168.16.49
010790: Jan 5 16:26:09.668 AZT: RADIUS: Nas-Identifier [32] 11 "router871"
010791: Jan 5 16:26:14.501 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010792: Jan 5 16:26:19.018 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010793: Jan 5 16:26:23.739 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010794: Jan 5 16:26:28.700 AZT: RADIUS: Fail-over to (162.168.16.49:1812,1813) for id 1645/3
router871#
010795: Jan 5 16:26:33.629 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010796: Jan 5 16:26:38.494 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010797: Jan 5 16:26:39.794 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010798: Jan 5 16:26:39.794 AZT: EAPOL pak dump rx
010799: Jan 5 16:26:39.794 AZT: EAPOL Version: 0x1 type: 0x1 length: 0x0000
0AD053D0: 01010000 ....
010800: Jan 5 16:26:39.798 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,EAP_START) for d8b3.7759.0488
010801: Jan 5 16:26:39.798 AZT: dot11_auth_dot1x_ignore_event: Ignore event: do nothing
router871#
010802: Jan 5 16:26:43.007 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010803: Jan 5 16:26:47.336 AZT: RADIUS: No response from (162.168.16.49:1812,1813) for id 1645/3
010804: Jan 5 16:26:47.336 AZT: RADIUS/DECODE: No response from radius-server; parse response; FAIL
010805: Jan 5 16:26:47.336 AZT: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
010806: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAIL
010807: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response
010808: Jan 5 16:26:47.336 AZT: Client d8b3.7759.0488 failed: EAP reason 1
010809: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: Failed client d8b3.7759.0488 with aaa_req_status_detail 1
010810: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for d8b3.7759.0488
010811: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client d8b3.7759.0488
010812: Jan 5 16:26:47.336 AZT: EAPOL pak dump tx
010813: Jan 5 16:26:47.336 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0004
010814: Jan 5 16:26:47.336 AZT: EAP code: 0x4 id: 0x1 length: 0x0004
0B060710: 01000004 04010004 ........
0B060720:
010815: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: sending data to requestor status 1
010816: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010817: Jan 5 16:26:47.340 AZT: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds
010818: Jan 5 16:26:47.340 AZT: dot11_auth_dot1x_send_client_fail: Authentication failed for d8b3.7759.0488
010819: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: sending data to requestor status 0
010820: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: client FAILED to authenticate d8b3.7759.0488, node_type 64 for application 0x1
router871#
010821: Jan 5 16:26:47.340 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010822: Jan 5 16:26:47.344 AZT: %DOT11-7-AUTH_FAILED: Station d8b3.7759.0488 Authentication failed
010823: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010824: Jan 5 16:26:47.972 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010825: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: req->auth_type 0
010826: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010827: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010828: Jan 5 16:26:47.976 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010829: Jan 5 16:26:47.976 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010830: Jan 5 16:26:47.976 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010831: Jan 5 16:26:47.976 AZT: EAPOL pak dump tx
010832: Jan 5 16:26:47.976 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010833: Jan 5 16:26:47.976 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0AD05B50: 01000031 01010031 ...1...1
0AD05B60: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0AD05B70: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0AD05B80: 72383731 2C706F72 7469643D 30 r871,portid=0
010834: Jan 5 16:26:47.996 AZT: dot11_auth_send_msg: sending data to requestor status 1
010835: Jan 5 16:26:47.996 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010836: Jan 5 16:26:47.996 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010837: Jan 5 16:26:47.996 AZT: dot11_auth_client_abort: Received abort request for client d8b3.7759.0488
010838: Jan 5 16:26:47.996 AZT: dot11_auth_client_abort: Aborting client d8b3.7759.0488 for application 0x1
router871#
010839: Jan 5 16:26:47.996 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
router871#
010840: Jan 5 16:26:58.634 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010841: Jan 5 16:26:58.634 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010842: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: req->auth_type 0
010843: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010844: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010845: Jan 5 16:26:58.638 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010846: Jan 5 16:26:58.638 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010847: Jan 5 16:26:58.638 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010848: Jan 5 16:26:58.638 AZT: EAPOL pak dump tx
010849: Jan 5 16:26:58.638 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010850: Jan 5 16:26:58.638 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0B060710: 01000031 01010031 ...1...1
0B060720: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0B060730: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0B060740: 72383731 2C706F72 7469643D 30 r871,portid=0
010851: Jan 5 16:26:58.658 AZT: dot11_auth_send_msg: sending data to requestor status 1
010852: Jan 5 16:26:58.658 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010853: Jan 5 16:26:58.658 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010854: Jan 5 16:27:01.603 AZT: dot11_auth_client_abort: Received abort request for client d8b3.7759.0488
010855: Jan 5 16:27:01.603 AZT: dot11_auth_client_abort: Aborting client d8b3.7759.0488 for application 0x1
010856: Jan 5 16:27:01.603 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010857: Jan 5 16:27:02.179 AZT: %SEC-6-IPACCESSLOGP: list ingress-filter denied tcp 32.42.41.254(57443) -> 72.201.117.84(59652), 1 packet
010858: Jan 5 16:27:02.179 AZT: %SEC-6-IPACCESSLOGP: list egress-filter denied tcp 22.3.184.118(0) -> 74.125.53.188(0), 4 packets
010859: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010860: Jan 5 16:27:12.261 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010861: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: req->auth_type 0
010862: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010863: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010864: Jan 5 16:27:12.261 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010865: Jan 5 16:27:12.261 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010866: Jan 5 16:27:12.261 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010867: Jan 5 16:27:12.261 AZT: EAPOL pak dump tx
010868: Jan 5 16:27:12.261 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010869: Jan 5 16:27:12.261 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0B060FD0: 01000031 01010031 ...1...1
0B060FE0: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0B060FF0: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0B061000: 72383731 2C706F72 7469643D 30 r871,portid=0
010870: Jan 5 16:27:12.285 AZT: dot11_auth_send_msg: sending data to requestor status 1
010871: Jan 5 16:27:12.285 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010872: Jan 5 16:27:12.285 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010873: Jan 5 16:27:12.293 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010874: Jan 5 16:27:12.293 AZT: EAPOL pak dump rx
010875: Jan 5 16:27:12.293 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0009
010876: Jan 5 16:27:12.293 AZT: EAP code: 0x2 id: 0x1 length: 0x0009 type: 0x1
0AD05290: 01000009 02010009 ........
0AD052A0: 01746573 74 .test
010877: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(CLIENT_WAIT,CLIENT_REPLY) for d8b3.7759.0488
010878: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_send_response_to_server: Sending client d8b3.7759.0488 data to server
010879: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_send_response_to_server: Started timer server_timeout 60 seconds
010880: Jan 5 16:27:12.301 AZT: RADIUS/ENCODE(0000019B):Orig. component type = DOT11
010881: Jan 5 16:27:12.305 AZT: RADIUS: AAA Unsupported Attr: ssid [282] 8
010882: Jan 5 16:27:12.305 AZT: RADIUS: 74 6F 79 73 6F 6E [toyson]
010883: Jan 5 16:27:12.305 AZT: RADIUS: AAA Unsupported Attr: interface [175] 3
010884: Jan 5 16:27:12.305 AZT: RADIUS: 36 [6]
010885: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Config NAS IP: 192.168.16.49
010886: Jan 5 16:27:12.305 AZT: RADIUS/ENCODE(0000019B): acct_session_id: 411
010887: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Config NAS IP: 192.168.16.49
010888: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): sending
010889: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Send Access-Request to 162.168.16.49:1645 id 1645/4, len 133
010890: Jan 5 16:27:12.305 AZT: RADIUS: authenticator 6F 6C 63 31 88 DE 30 A2 - C2 06 12 EB 50 A3 53 36
010891: Jan 5 16:27:12.305 AZT: RADIUS: User-Name [1] 6 "test"
010892: Jan 5 16:27:12.305 AZT: RADIUS: Framed-MTU [12] 6 1400
010893: Jan 5 16:27:12.305 AZT: RADIUS: Called-Station-Id [30] 16 "0019.3075.e660"
010894: Jan 5 16:27:12.305 AZT: RADIUS: Calling-Station-Id [31] 16 "d8b3.7759.0488"
010895: Jan 5 16:27:12.305 AZT: RADIUS: Service-Type [6] 6 Login [1]
010896: Jan 5 16:27:12.305 AZT: RADIUS: Message-Authenticato[80] 18
010897: Jan 5 16:27:12.305 AZT: RADIUS: 9D D5 62 1A 38 13 94 30 3A 43 D7 A4 AE A4 43 64 [??b?8??0:C????Cd]
010898: Jan 5 16:27:12.305 AZT: RADIUS: EAP-Message [79] 11
010899: Jan 5 16:27:12.305 AZT: RADIUS: 02 01 00 09 01 74 65 73 74 [?????test]
010900: Jan 5 16:27:12.305 AZT: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]
010901: Jan 5 16:27:12.305 AZT: RADIUS: NAS-Port [5] 6 664
010902: Jan 5 16:27:12.309 AZT: RADIUS: NAS-Port-Id [87] 5 "664"
010903: Jan 5 16:27:12.309 AZT: RADIUS: NAS-IP-Address [4] 6 192.168.16.49
010904: Jan 5 16:27:12.309 AZT: RADIUS: Nas-Identifier [32] 11 "router871"
010905: Jan 5 16:27:16.642 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/4 -
Client Exclusion Policies on WLC not working with ISE as RADIUS Server
Hi,
for our Guest WLAN (Security Setting for this SSID:Layer2: MAC filtering, Layer3:none) we use ISE as RADIUS Server. On WLC I enabled client exclusion polices and checked all options (Excessive 802.11 Auth. Failures etc..).. But even if a client fails 20times at authentication, it is not excluded on the wlc. It works with other SSIDs, where security settings are set to 802.1x.
Am I missing any settings here or do you have some tipps on how to troubleshoot this?
Thanks very much!Hi Renata,
If those guest failures are not associated with valid guest users (i.e. people who have forgotten their account or entering the wrong password) there isn't anything that can be done. The main point of Guest WLAN is to make it as easy as possible for Guests - individuals with device configurations you don't want to deal with or know about, to connect your network for internet access. From a WiFi/802.11 perspective, the standard Guest WLAN setup means its easy for any device to connect.
If your Guest WLAN has the following:
SSID is broadcast enabled, Security = OPEN, Encryption = none, then any 802.11 device can find the WLAN via passive scanning and connect. And any device that connects will get the ISE portal. Once recieveing that portal they can guess away at valid username/password.
I would suspect that unless your Guest WiFi is adjacent to a Mall, school, hotel or other hi-density area of individuals with time and electronics on their hands, other than alerts in your ops window and logs, resources associated with this (WLC & ISE) are very low.
You can try and dull the noise a few ways.
Option 1. create and ISE log filter on those alerts so they don't cluter the console.
Option 2. Stop broadcasting the SSID. This is not a security measure, but will cut volume of people connecting to the SSID significantly. You will have to tell your guests what SSID or include it in their credential communication.
Option 3. Put a very simple PSK on the SSID. The PSK will become a public secret - shared with valid guests, doesn't have change as it's purpose is not security. You will have to include this information on their credential communication.
Option 4 - both 2 and 3
The most effective option would be 3.
Good Luck! -
AP won't talk to Radius Server
I have a 350 AP (v12.00T) setup for Network-EAP. When I try to associate with it I keep getting "EAP retry limit reached for Station". I've sniiffed the ethernet port and the AP is not even trying to contact the Radius Server.
Anybody have any ideas why this might be happening?
BenThanks for the reply
I've now gotten my 350 AP to send a request to my RADIUS server (MS Win2k IAS), but the client is sending it's MAC address and not asking for user name, password, and domain like it's supposed to when doing PEAP. Everything is the newest version.
I've followed the following instructions:
http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo_350/350cards/windows/incfg/win_appe.htm#97267
http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo_350/350cards/windows/incfg/win_ch7.htm#xtocid23
Any ideas on how to force it ask for username and such?
Ben -
WLC log RADIUS server failed to respond to request
I'm keep on getting same couple MACs being failed. I was hoping somebody has more inside about this? Radius server is pingable from WLC. People are authenticating. Please let me know what log should I provide. Thank you in advance.
Thu Feb 20 16:22:06 2014
RADIUS server 10.4.120.251:1812 failed to respond to request (ID 78) for client 3c:a9:f4:42:11:a0 / user 'unknown'
3
Thu Feb 20 16:22:06 2014
RADIUS server 10.4.120.251:1812 failed to respond to request (ID 77) for client 24:77:03:20:78:d0 / user 'unknown'
4
Thu Feb 20 16:22:06 2014
RADIUS server 10.4.120.251:1812 failed to respond to request (ID 76) for client 24:77:03:d0:bd:b4 / user 'unknown'
5
Thu Feb 20 16:22:00 2014
RADIUS server 10.4.120.251:1812 failed to respond to request (ID 75) for client 24:77:03:26:86:7c / user 'unknown'
6
Thu Feb 20 16:21:59 2014
RADIUS server 10.4.120.251:1812 failed to respond to request (ID 74) for client 24:77:03:20:78:d0 / user 'unknown'
7
Thu Feb 20 16:21:59 2014
RADIUS server 10.4.120.251:1812 failed to respond to request (ID 73) for client 3c:a9:f4:42:11:a0 / user 'unknown'
8
Thu Feb 20 16:21:59 2014
RADIUS server 10.4.120.251:1812 failed to respond to request (ID 72) for client a0:82:1f:d8:24:02 / user 'unknown'You should look at the ACS logs as that will give you a better idea of the failure.
Sent from Cisco Technical Support iPhone App -
I have setup NPS for Radius / Mac authentication to my Meru Wireless controller, I've created user accounts for my mac clients. The request to connect to the wireless controller is setup and the connection is authenticated on the controller, the controller
then sends the request to the AD Radius server with mac username and password for authentication and it fails. The NPS returns an error that the username and password have a mismatch.Hi,
First please make sure that the username and password are correct. Do not forget to add the domain name after the username. Normally, it should like
[email protected] or YOURDOMAIN\username.
Please check if the NPS server has been registered in the domain controller. To verify this, please check if the NPS server has been added into the
RAS and IAS Servers group in the domain controller.
If issue persists, please provide the detailed configuration of your Network Policy. It may give some hints.
Best Regards.
Steven Lee Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected] -
Cisco Switch connecting to Radius Server
Hello Team,
I discovered that anytime the Uplink of my Cisco C2960CG-8TC-L goes down and reconnects, before the switch connects with the Radius Server, the access ports starts to connect into Guest VLAN, which is not the correct production VLAN that has been assigned to the Mac addresses.
I thought I could resolve this with Link state track Upstream and Downstream, but it's not working effectively.
The solution to the problem should be when the UPLINK port does down for whatsoever reason and comes back up, it should communicate with the Radius Server first, thereafter the access ports comes up and connect to the assigned Production VLAN not the Guest VLAN.
How do I achieve this? Any positive advise would be highly appreciated. Configuration can be uploaded if needed.
Thanks
PeterI haven't ever done it, but I think you can set up the Access point as a radius server. Then configure Mac authentication and either filter with the local list or an access list.
Thanks,
Alex -
Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points
Hi Guys,
I would like to go for "Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points 1300". I want the AP to broadcast only 1 SSID. The client find the SSID ->put in his user credential->Raudius athentication->assign him to an specific vlan based on his groupship.
The problem here is that I don't have a AP controller but only configurable Aironet Access Points 1300. I can connect to the radius server, but I am not sure how to confirgure the AP's port, radio port, vlan and SSID.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
I go through some references:
3.5 RADIUS-Based VLAN Access Control
As discussed earlier, each SSID is mapped to a default VLAN-ID on the wired side. The IT administrator may wish to impose back end (such as RADIUS)-based VLAN access control using 802.1X or MAC address authentication mechanisms. For example, if the WLAN is set up such that all VLANs use 802.1X and similar encryption mechanisms for WLAN user access, then a user can "hop" from one VLAN to another by simply changing the SSID and successfully authenticating to the access point (using 802.1X). This may not be preferred if the WLAN user is confined to a particular VLAN.
There are two different ways to implement RADIUS-based VLAN access control features:
1. RADIUS-based SSID access control: Upon successful 802.1X or MAC address authentication, the RADIUS server passes back the allowed SSID list for the WLAN user to the access point or bridge. If the user used an SSID on the allowed SSID list, then the user is allowed to associate to the WLAN. Otherwise, the user is disassociated from the access point or bridge.
2. RADIUS-based VLAN assignment: Upon successful 802.1X or MAC address authentication, the RADIUS server assigns the user to a predetermined VLAN-ID on the wired side. The SSID used for WLAN access doesn't matter because the user is always assigned to this predetermined VLAN-ID.
extract from: Wireless Virtual LAN Deployment Guide
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00801444a1.html
==============================================================
Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller Configuration Example
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
==============================================================
Controller: Wireless Domain Services Configuration
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801c951f.shtml
Any help on this issue is appreicated.
Thanks.I'm not sure if the Autonomous APs have the option for AAA Override. On the WLC, I can go into the BSSID, Security, Advanced, and there's a checkbox that I would check to allow a Radius server to send back the VLAN.
I did a little research and it looks like the 1300 may give this option but instead is defined as "VLAN Override". I've found the release notes for 12.3(7)JA5 (not sure what version you're running) that give mention and a link to configuring EAP on page 4: http://www.ciscosystems.ch/en/US/docs/wireless/access_point/1300/release/notes/o37ja5rn.pdf
Hope this helps -
Hi
I am trying to setup the Radius server on my Mac OSX 10.5.2 server. I have two Airport Extreme 802.11n base stations connected to my network, one which we use normally for wireless access and another that I am using to test and get the Radius Server configured. One has an address of 192.168.10.5 and the other is 192.168.10.6. All my wireless clients can browse the net without any issues.
When I go into Server Admin and select Radius and then Configure Radius Service, I select the default certificate and am then presented with a screen where I add my base stations. Now, the puzzling thing is that both of my base stations appear, but they are showing 169.254.xxx.xxx addresses. So, my first question is why do they show self assigned IPs? Is it because they are being found using Bonjour?
If I then back out of this screen and select the Base Stations icon in the menu, I can click browse and again it shows the AEBSs but again with a self assigned IP. Another interesting point is that if I select my normal base station, in the info below it shows the Ethernet and Airport ID info showing V7.3.1 software version but a picture of the old dome shape Airport Extreme Base Station. If I select the test base station, I get the same info but THE RIGHT PICTURE !
If I then select the test base station and enter the password, it says it's the wrong password, even though I know it's the right one.
I'd like to get past this point, but can't see how to proceed until the IPs are right. What's going on? Any ideas gratefully received.
PaulI have just purchased a new AirPort Extreme to begin testing to rollout wireless using RADIUS on our Mac OS X 10.5 server.
I am having a bit of trouble setting up the actual base station. I too was having the same problem with the IP address showing up on the RADIUS server as self-assigned 169. but noticed that when I changed the Primary RADIUS IP address to something different to the AirPorts Ethernet IP address it showed up correctly. Maybe I am wrong but that's what I think happened.
The problem I am having is this: I have created a wireless RADIUS network. My client was able to log in and connect to the wireless system, but I am not getting any DHCP information from my DHCP server running on Mac OS X Server. What am I doing wrong. What settings should be entered for Primary RADIUS IP Address, Shared Secret, etc. I am a bit confused an Apple hasn't provided technical documentation on this aspect.
Help! -
Connecting Windows 7 to Apple Radius server
Anyone know how to get a windows 7 machine to connect to an apple radius server? My macs work great and authenticate perfectly, but my windoww boxes won't connect at all.
Please check out the following Apple Support article for details on how to access a HDD attached to an AirPort Extreme Base Station (AEBS) from either a Mac or PC.
-
Question about RADIUS server configuration with a MacBook Pro
Hello,
I own a modem router which is capable of WPA2 Enterprise and I want to use it with a RADIUS server for authentication and security purposes.
However, I have a few doubts about this.
MY CONFIGURATION:
The modem router would be connected to a fixed PC with Windows and to a MacBook Pro (both with Ethernet)
The RADIUS server would be running on the MacBook Pro (freeRADIUS)
The bold is the issue, that comes when I disconnect the MBP (it's a notebook, so I use it disconnected from the router sometimes).
Supposing the router would have recognized it (correct configuration), it would disconnect from it.
My questions:
Would Wi-Fi be lost in this manner? Or would the modem router automatically switch to another Wi-Fi authentication?
If I reconnected the MBP to the modem router and re-run the RADIUS server, would I need to access the control panel and re-configure the WPA2 Enterprise in order for Wi-Fi to work again?
Thanks in advance,
Tyrexionibus"Full HD 3DD camcorder..." Marketing at it's best.
This is HDV, right? HDV has the same data rate as DV...13.6GB/hour. But because of the MPEG-2 Long GOP format the HDV format employs, it can be a bit tough to edit, but mainly when rendering effects. IT will be slower than DV, and you can't monitor thru the camera like you can with DV, but a simple FW400 drive and Intel Mac will be fine. Better if you can convert to ProRes upon ingest, but then that eats up a LOT more space and requires at least FW800...
http://library.creativecow.net/articles/poisson_chris/hdv-prores.php
Shane
Maybe you are looking for
-
I customize my genres, etc. but iTunes keeps changing it back. How do I stop this?
-
Hi All, Recently purchased a T43 on e-bay to replace a deceased T42. Overall, love the machine, really missed having a ThinkPad when I was between machines (was using an Acer for a bit....awfull machine) Have had some issues with my "new" machine th
-
Standby database SRL & Online logs
Hi, I have just tried my hand at building a Physical standby database in Oracle 10gR2 using RMAN. I will detail out the steps that i have performed before asking my question. I configured every pre-requisite and i did not create any SRL's on primary
-
WAD-Error configuration.
Hi Gurus, I am presently working on WAD in my sandbox system. Problem: Our's WAD is not configure when i try to save a template I get following error. Portal unavailable or config problem. please contact system admin. Can any one give me hint how to
-
Hyperlink button doesnot work in IE
I created a hyperlink button to take to a HTML page on an existing silverlight application. The button and the webpage works fine with Google chrome and firefox however, it doesnot with Internet explorer 9 and 11. I made sure the manage add ons the s