Ram Issues with a Hp Pavilion a6357c or maybe the amd athlon 64 5000+
I am really not sure if I am in the area-of a post like this. Please excuse my grammar and spelling"will try and use spell check"...
I got this computer from a friend of mine.Total nightmare. Was told all it needs is a hard drive and maybe a video card..Boy was that not the issue. I first got it and plugged it-make sure it would boot to bios..Nothing computer turned on-fans and all..Nothing on the screen. To make a long story short...I found an old ps2 mouse..The mouse was defective...with that mouse plugged in-computer wouldn't even boot to bios..Fixed that issue. Got into bios and all was good. Next step..Video card-Bought a new pny 9500 GT and a TTGI 550 power supply....swaped it all out and it works great...Than found a hard drive SATA 2...everthing installed and ready to place an operating system on....
Windows 7 64 bit--Installed great...But when it came up to the start up---Freeze--blue screen...Ok thought maybe it was the ram.....ended up taking all the old ram out and replace it with some DDR2 6300--or what ever the max was...total of 6 gb...still issue...freezing--decided to boot into safe mode---all good and ran great....checked Ram-stress test-checked every little hardware--stress test-no issues...Booted back up out of safe mode... Same issues....ok--lets just try Windows 7 32 bit.....
Windows 7 32 bit.....Install went great-no issues....updated and all the sp's...but underload----bluescreen....played and played with it...but the blue screen were all over the place...back into safe mode and checked all the drivers--and devices....Ok lets just go back to what the system had----windows Vista....
Again----everything boot and installed perfect...This time was a liitle more stable...updates--all the sp's all the drivers.....
Blue screen underload......Ok maybe my ram is at fault.......
It ended up stable and working perfect---single channel mode-2 gb in the first slot....I tried every way to put the ram in.....
found out--ok---only stable in single channel mode...anytime I added ram--for dual channel...Fail under load....Put the 2 gb stick or a 1 gb stick any any of the other slots-by itself---perfect stable and running great...I was even able to add another 1 gb stick with the 2 gb stick---but it had to be in single channel....tried to add more in single channel and fail....3 is it and it is not all the way stable--but stable enough to run...2 gb stick by itself---perfect.........
Did some digging---maybe it is the memory controller...But can not find any post with this issue---I keep finding people asking the quesion--and there storys match...But no answers and it seems that the just get a walk around.....
I have narrowed it down..It has to me the intergrated memory controller on the chip....so i think...I could just purchase a new one and swap it out........But here is the issue...........
Safe Mode will take all the ram-dual channel---single channel..anyway.......But so will linix-----Only has this issue with Windows....
The other werid item too---My had drive say scis drive or something along that lines--Not sata.....and again-I can not find a post to explain why......
Please understand----Stress test on Ram-cpu-motherboard--videocard----everthing--is perfect no issues...PSU is perfect---checked it out in another sytem---no issues....I am at my witts end with this thing and I have got nowhere......
It is working great with just a 2 gb stick of ram---very fast and very responsive....But adding extra ram really bothers me...Not because--it make a differance-Just because I don't know...
Can somebody out there school me.....I have tried everything........
Sorry all-But i never got a reply to this situation. But I am done. I ended up running threw tons of post and tons of threads. I can tell you that when people ask a question. There is always some smart A--, telling them something that has nothing to do with the current situation. I guess alot of people out there think they know everything- and have nothing to do-but mess with the people like me when they are stumped. Anyways...I ended up running a computer check in or after bios...I think they call it burned in-HP....what ever-the last straw when you can not figure it out..Ran it with one stick---than with all the sticks..Everytime--it claimed that there was nothing wrong..But when I tried to restart it--boom blue screen..with the mulyi sticks of ram. So when I couldn't find an solution online...I stoped using the words HP a6357c.. and just typed the issue..Funny thing the issue kept poping up--and with the same motherboard or processor...and again-nobody ever came up with a solution..Most of the post claimed the issue was the power supply....ot the ram timming..But I know better..Not to mention people kept saying-buy the tool from ebay to check wattage usuage.....Bam----wattage...Did a simple check with harware monitor...my 3.5 or 3.3 rail was running at 1.78....enought to power one stick of ram---not 2...or barley enough to power a 1 gb stick and a 2 gb stick in single channel mode...Again-people were blaming--PSU"not my case".Ram Timming.."not my case".........Then I found a person with the same make and model.....Look for fat or bad capasitors...Never thought of that.....Guess what------That is what I found....No body but a thread-one thread has explained...If you have this same issue-Look at the capasitors...Maybe this is a defective motherboard--you can not find it on the site anyway-no specs nada..like it was a mistake..So if you have one just like this- I have a feeling-you will run into this issue-in one way or another..I just don't understand why both companys have no fix--or no--recall info..No answers to problems on these....now I have a big black paper weight.....sorry for my spelling and grammer-just so mad..the net was no help on this
Similar Messages
-
Ram issues with my hp pavilion p7-1459(joshua-H61-uATX mobo)
I traded my buddy my original 2 sticks of ram that came with the computer (2x 4gb sticks) not sure what the specs on them were, but that is easy enough to find out. Anyways, my buddy gave me his 1 stick of 8gb gskill ripjaws x ram (ddr3-1333 pc3-10666). when i put in the gskill ram my computer refuses to boot, although my motherboard says that it takes ddr3-1333. so i am very confused. Additionally my room mate gave me a stick of 4 gb ram out of another hp prebuilt and that stick alone will run my system. ive tried consulting google about this with no avail, im hoping someone from here can help me out, thanks..
Ps. i am also running a 650w psu and a geforce gtx 760 gpu.Hi,
Are you a gamer as perhaps indicated by your name?
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT -
I am having major issues with links in keynote! Even though the links (a navigation system) are on the master page, they are only working on some of my slides. Anyone have ideas on how to fix this or similar issues? Help!
I have created a navigation system on the master pages and set the presentation to links only mode. I also have other links scattered throughout the program, like a linkable table of contents, etc. Some of them work, some of them don't. Not sure why. Anyone out there having similar issues? Or have any idea on how I can solve this issue? Any help would be appreciated!
Thanks!Links should not create any problems in Keynote. If they are set up correctly on text, the text will be underlined. Objects that have links will have a curved arrow bottom right, if you click the arrow a popup will display the link information.
Try this repair for Keynote, ensure you complete all the tasks and in the order shown:
1
delete all the iWork applications if you have them, not just Keynote, using Appcleaner from Mac Update, its a freeware application
2
empty the trash: Finder > Empty Trash
3
Shut down your Mac, wait 30 seconds, then power on the Mac, immediately after the start chime, hold down the Shift key
When you see the grey Apple symbol and progress indicator (a spinning gear), release the Shift key.
If you are prompted to log in, type your password, then hold down the Shift key again as you click Log in.
4
Let the Mac fully boot up, it will take longer as the OS is repairing the drive
5
when fully booted, go to Applications > Utilities > Disc Utility; click on the boot drive then First Aid tab and click repair disc permissions
6
when complete, restart the Mac normally, Apple menu > Restart
7
install Keynote from the Mac App Store
let us know if this helped -
My debit card kept getting rejected by my iTunes account, it there an issue with iTunes? I have been using the same Card since very long time. I downloaded the iOS 8, can I talk to someone so I can get this resolve?
Apple is not here. Contact Apple to resolve your issue:
iTunes Support WorldWide
or
iTunes Support by eMail ww
Cheers,
GB -
We had some accuracy issues with NI 5112 scope in one of the ATE and then I decided to perform self calibration using Labvidew vi to perform “niScope_CalSelfCalibrate(handle, "", 0);” function.
But it made it worse. I tried using option 2 to restore but it did not work.
Could you pls advice me to resolve this issue.Hi Ana10,
Are you using this digitizer with NI VideoMaster? if not you should probably post this in the Digitizer forums. That said I would suggest using the self calibrate function in MAX for this device rather than the LabVIEW API method just so that you can rule out any errors in correctly configuring the digitizer for self cal in LabVIEW. Also you should ensure that all inputs are disconnected before performing a self cal. If this still results in an error in calibration you could refer to the following document or arrange to return the digitizer to NI for external calibration.
http://www.ni.com/pdf/manuals/370328e.pdf
Hope this helps,
Nick -
A SERIOUS issue with WIFI in Pavilion 15-p002nk
Hi , Thank you for visiting the HP Support Forums and Welcome.Thank you for the very detailed information. I have looked into your issue about your HP Pavilion 15-p002nk Notebook and issues with the Wireless disconnecting. Here is a link to the troubleshooting the Wireless connection, if you need it.
If this continues I would change the Channel on the router. Routers are capable of communicating to your Notebook on several different channels. If your neighbours Wi-Fi is on the same channel, your network speeds might have issues. Some say this helps fix this problem Microsoft Fix it. Here is a link to help as well. Hope this is helpful. Thanks.Hi all.. Since the time i bought my new PC laptop "HP Pavilion 15 Notebook PC, Number: 2S23EA#BH4" , I've an issue with Wifi Connection; it's discconecting by itself sometime without any reason, then, it reconnect again like nothing happend because the "Connect automatically " option on Windows 8.1 is checked. Although, sometimes when it disconnect I have to reconnect by myself, after many troubles like I have to restart the computer, or activating the Airlplane mode, disabling the Wifi cards and enable it again.. The strange behaviours of the Wifi connection is that is sometimes show me that the Wifi's stengh is full, all 5 bars, while it should be just like 2 bars or 3 at maximum, because where I'm connecting is a bit far from the router. but this just for few seconds before disconnecting, in addition, sometimes the Wifi card disable itself and re-enable at the moment and reconnect again. Moreover, once upon time when it disconnect, it dosen't detect my router or any other Wifi network around me. while there's more than 6 Wifi's available where i am living. Generally, this issue is not excessive, but those last days, it is being immoderate. i tried to look for some solution, but none of those proposed solution worked for me. I wish that i can find some resolution of this annoyning problem. advance Thank for everyone.
-
The infamous RAM issue with bootcamp
Sp, I have seen a lot of threads about RAM issues when using bootcamp.
I'm about to install Windows XP SP 3 using bootcamp - how much RAM will be utilized when using my windows partition?
I have a MBP 2.33 Ghz Intel Core 2 Duo with 3 GB RAM and Radeon X 1600 256 mb RAM.
Looking forward to your responses.
ThanksThis is not so much an issue with Bootcamp as it is an issue with Windows. On any machine, Mac or PC, Windows will only recognize approximately 3GB of RAM. The only Windows Operating Systems that are capable of going higher are the 64-bit OS choices. So, if and when you upgrade your MacBook Pro to 4GB of RAM, Windows will still only see 3GB. Just a heads-up.
-
Hello
I wonder if some one could help me one...... 2-3 years ago i bought a new pc system..... but i still have ram issue!
my PC contains: MSI x58m bios version 3.8 , i7 950 3.07Ghz, Crucial Ram 1333 6GB (1gb x 6) DDR3 240pin , video card ati Club 3d HD4890, Win 7pro SP1 64bit
from day 1 i had problem - unexpected restarts...... my pc store exchanged mother board twice, gpu 2 times and 1 time ram..... nothing helped i only lost 2 weeks! But pc started working fine only after in bios we changed the ram MHz from 1333 to 800mhz! after that system was stable no restarts
could some one plz tell me what is the problem and how to avoid it?
some info from my ram: CT12864BA1339.M8SFD , BL1119M.3V, 200933 SU
regardQuote from: anat_usa on 10-July-12, 18:00:52
# of Memory Channels - 3
but for some reasons i cant use 1066
that is simple to explain 1066 would work with 3 sticks of ram installed but you have 6 so the max is 800mhz as you have 2x3 channel memory installed and the cpu cant handle that much at full speed!
its all down to the CPU's (Central Processing Unit's) memory controler Quote from: anat_usa on 10-July-12, 18:09:15
i have chievtec 750w, -
my GPU needs only 500 Watt or greater power supply with two 75W 6-pin PCI Express® power connectors recommended (600 Watt and four 6-pin
club-3d.com/index.php/products/reader.en/product/hd4890.214.html
seems like should be ok.....
not the point wattage ratings are meaningless its all down to how that is sub-devided on its rails as ampages i have a 1000W psu here that can't boot a single 24A graphics card as it has 4 x 20A +12v rails and is only usefull as a paper weight!
what are the ampages of its +12V rail or rails? there the important data points to pay attention to! WATTAGE OF A PSU REALLY MEANS NOTTHING ITS ALL ABOUT AMPAGE IT CAN DELIVER ON THE RAILS!!!!!! minimum Wattage psu calculations are done based on a single high ampage +12v rail and if yours has 2-3 +12v rails its no better then a 300W psu at best!
that HD 4890 you have requires this:
18A idle power draw = 216W
28A under load = 336W
that is very power hungery at idle probaly neer the max your psu can put out on a +12v rail! -
Hello,
I am a very happy owner of an 3.06 gh imac and love it .
I upgraded the ram to 4Gb.
imac accepted it and it works well.
But ram fills up so quickly , amazing.
Like when i imported pictures it used all 4 gb of ram while importing.
Also it uses ram for apps and then when i quite the app the ram usage in the activity monitor doesnt go back as it was before like somehow still shows used.
Is there any program to check if my installed ram is well used?
It seems yes but then why is so quickly used?
and why it doesnt show availble as before using app , when i quit app?
If i dont upgrade to 4 gb , would it mean that my system wouldnt run?
As now the machine allways uses more then 2 whenever i open a few apps.
Before the upgrade for the same apps it used less then 2...
Also windows xp under vm fusion .. when i use it again the ram is over 2 gb .. would it mean the without 4 gb of ram i wouldnt be able to use fusion?
I dont understand..
Thank you a lot for helping me on that, and also with a program to test it.
Regards
Anteros
Message was edited by: anteros27You should not worry about free memory unless your system is spending a lot of time doing pageout I/O.
Any operating system that maintains a lot of free memory is *wasting your money*. The operating system should maximize the use of memory so that you get the best performance for your money.
Mac OS X will use memory for a file system buffer cache. It will keep previously executed program code in memory just in case you quickly re-run that program, so it does not need to read it back from disk.
Many programs, especially programs that process graphic images will consume large amounts of memory. That memory may remain as file system buffer cache.
All cached memory or is available, the same as free memory, anytime the operating system need it for something else.
If you are concerned that your performance is suffering, you can run the following utility from an Applications -> Utilities -> Terminal session:
sar -g 60 100
This will report the pageout operation every minute for 100 minutes. If you have mostly zeros then you enough memory. If you see sustained pageout numbers over an extended period of time, especially if you have high numbers, then you would benefit from more memory, or running fewer high memory demanding programs at the same time.
Remember if you always have lots of free memory, then your OS is wasting your money -
Upgrading from 10.4.7 have fixed many of my problems. Certain apps take up more cpu power and ram i assume. It will freeze almost within 10 minutes of use. If i dont manually restart by holding the power button down. Within 2-5 minutes the black screen with 4 languages stating power down comes up.
But I did something interesting, I swapped my 2 1GB cards with each other, and now it only registers 1.5 GB instead of saying 2GB. And it has fixed all the problems.
My question is why would tiger not register 50% of one of the ram chips. Here is my scenario based on my experiences.
BEFORE TIGER:
Slot 1 Chip A(1GB)
Slot 2 Chip B(1GB)
Computer states 2 GB DDR SDRAM
AFTER TIGER
Slot 1 Chip A(1GB)
Slot 2 Chip B(1GB)(only registering as 512)
Computer states 1.5 GB DDR SDRAM
AFTER TIGER UPDATE TO 10.4.8 and all is wrong! *Notice chips are swapped below* Now my computer shows 2GB. But I have a slew of problems, freezes, hangs, black kernal panic screen
Slot 1 Chip B(1GB)
Slot 2 Chip A(1GB)
Computer states 2 GB DDR SDRAM
AFTER TIGER UPDATE TO 10.4.8 and all is fixed
Slot 1 Chip A(1GB)
Slot 2 Chip B(1GB)(only registering as 512)
Computer states 1.5 GB DDR SDRAM
The 2 ram chips I purchased was from MAC Mall, and it is Axiom AXA-PBG4333/1G 1GB PC2700 DDR SO DIMM for APPLE POWERBOOK G4 15in & 17in.
Any help would be greatly appreciated.
Thanks again
Brian
Powerbook G4 Mac OS X (10.4.7)Hello Brian.
Since you have experienced kernel panics, sounds like you have a RAM problem since incompatible, defective or failing RAM are the most common causes of kernel panics.
If you are experiencing many problems, it is generally recommended to resolve the problems before installing a major OS Update such as 10.4.8 since not doing so will usually not resolve the problems and sometimes make matters worse.
Unless you are experiencing a problem that an OS update addresses specifically, you should resolve existing problems before doing anything else.
Unless your RAM was not seated properly, I would focus on the RAM chips. Assuming you have the original RAM chip that shipped with your Mac, the best method for testing RAM is via a process of elimination. If the same problems do not occur when using the original RAM chip that shipped with your Mac when purchases, you need to return the RAM for exchange or credit if possible.
Check this link for information on the causes of kernel panics and a roadmap of troubleshooting steps to take in the order provided to resolve focusing on the hardware test and RAM testing.
http://www.thexlab.com/faqs/kernelpanics.html -
Issue with LCM while migrating planning application in the cluster Env.
Hi,
Having issues with LCM while migrating the planning application in the cluster Env. In LCM we get below error and the application is up and running. Please let me know if anyone else has faced the same issue before in cluster environment. We have done migration using LCM on the single server and it works fine. It just that the cluster environment is an issue.
Error on Shared Service screen:
Post execution failed for - WebPlugin.importArtifacts.doImport. Unable to connect to "ApplicationName", ensure that the application is up and running.
Error on network:
“java.net.SocketTimeoutException: Read timed out”
ERROR - Zip error. The exception is -
java.net.SocketException: Connection reset by peer: socket write error
at java.net.SocketOutputStream.socketWrite0(Native Method)
at java.net.SocketOutputStream.socketWrite(SocketOutputStream.java:92)
at java.net.SocketOutputStream.write(SocketOutputStream.java:136)
at java.io.BufferedOutputStream.flushBuffer(BufferedOutputStream.java:65)Hi,
First of all, if your environment for source and target are same then you will have all the users and groups in shared services, in that case you just have to provision the users for this new application so that your security will get migrated when you migrate the from the source application. If the environs are different, then you have to migrate the users and groups first and provision them before importing the security using LCM.
Coming back to the process of importing the artifacts in the target application using LCM, you have to place the migrated file in the @admin native directory in Oracle/Middleware/epmsystem1.
Open shared services console->File system and you will see the your file name under that.
Select the file and you will see all your exported artifacts. Select all if you want to do complete migration to target.
Follow the steps, select the target application to which you want to migrate and execute migration.
Open the application and you will see all your artifacts migrated to the target.
If you face any error during migration it will be seen in the migration report..
Thanks,
Sourabh -
Issue with PO Currency when currency changed after the approval.
Hi All,
we have get an issue with PO currency which is as follows
Step1:Created a Limit PO with value 3.701,00 CHF and sent it for approval,,and PO is approved and transfered to backed (We are using "Extended classical scenario' .
Step2:but we got to know that the PO value should be in USD ,so will go to PO and changed the currency value to USD ,it coveted value to 3421 but ,since i need the 3701 USD i changed the value to 3701 at item level and orderd the PO.
but after approval , when it transfered to backed it is showing the value 3.701,00 USD at header level ,but 3.402,84 USD at item level.
so when we are trying to create GR it is populating 3.402,84 USD but we need 3701 USD.
is any one know the what is the problem with this.
please help
Regards
cbYou can re-output a message that has already been outputted (printed or transmitted).
"Repeat message" function
You use this function if you wish to print out or transmit again a complete purchasing document that has already been outputted. Note that the system takes account in the message of any changes made to the purchasing document since it was last outputted - i.e. the system always outputs the current status of the document. If you wish to have old statuses available, you must optically archive the purchasing document.
Activities
You invoke the Messages screen as follows:
Via the purchasing document itself (Header Messages) or
Via <Purchasing document> Messages Print/transmit.
Enter the processing status 1 (successfully processed) and display the messages.
Select the desired message and choose Goto-> Message details.
Choose Edit-> Repeat message or Change message.
The system inserts the new message. If a change message is involved, the system sets the Change indicator.
Save your data.
Hope you find this useful.
Edited by: Reetesh on Dec 3, 2011 7:36 PM -
Some of the photo I take with my iphone will not get saved into my photo stream. Some of these photos were taken while the iphone was connected to the wifi, but did not get saved. Other photos were while not on wifi and they seem to get saved. I have not narrowed down what is the difference between those photos that get saved and those that don't get saved. Is there a way to force a photo to get saved? I would like to be able to access these photos from all my devices.
I also have an issue with the photo stream on my PC getting updated. I have photos in the photo stream that is updated on my Ipad and iphone. However, these photos are not getting updated on the PC. Everything seems to be set up on the icloud and photos stream for the PC.
Thanks,That is the way it is designed to work. If you want the photos on your Mac on your new iPhone, you can sync them with iTunes.
-
Issue with re-connecting a Client Computer to the Server Essentials R2 2012
I have an issue re-connecting a Client Computer to Server Essentials R2 2012. The Client Computer in question was connected to the Sever originally. I started getting Error Messages indicating that I was running out of storage room. I
had been wanting to re-configure this Server with additional Hard Drives for some time, but something else always came up first. Now, I was forced to address the problem. I shut down the Server and added additional Hard Drives and while I was at
it I replaced the original Hard Drive that the Server Operating System was on with a much smaller Hard Drive, and reinstalled Server Essentials on that Drive. Everything was working fine and the Server Back-up went fine to an external Hard Drive.
I was ready to re-install my Client Computers. I started with my primary Production Computer first. The Connector Software seemed to install fine, but as I moved through the Connection Wizard I received the following Error Message: "Cannot
connect this computer to the network. This computer is already connected to another Windows Server Network. Before connecting this computer to the Windows Server Essentials network, you must remove this computer from the current network.
To resolve this issue, contact the person responsible for your network". I am the Administrator. I removed the Connector Software following the instructions in the "Troubleshooting connecting computers to the Server", but I continue
to get the Error Message whenever I attempt to re-connect the Client Computer. I have not attempted to connect any of the other three Client Computers yet as I need to resolve this issue first on my primary production machine. Where am I going
wrong? Does anyone have any suggestions?Hi PARADOX-RED,
Based on the error messages that you provided, please remove the connector software from Control Panel completely. Then, in the problematic computer, please locate
to: Control Panel-> System-> select Change settings. And select the Computer Name tab in the System Properties dialog box, click
change button. Then in the Computer Name/Domain Changes dialog box, please take the computer out of the domain as a workgroup, and rejoin in new domain.
Please check if this issue can be solved. If it still exists, please don’t hesitate to let me know.
Hope this helps.
Best regards,
Justin Gu -
Issue with TestStand 2010 or 2012 hanging on the first step after continuously running TestStand?
I am having issues with a CVI test sequence hanging in TestStand 2010 & 2012. Currently, the only way to resolve this is to exit/close TestStand. Following this we must replace the entire project with a backup project. This only occurs about once a day or so with the sequence running continuously. It will hang on the first or second step in the sequence, usually the first step. The project uses several continuous XINET CAN messaging, so I wonder if this could be related to that.
Yes, I have. It hangs at the first statement in the code after all the variable defines. It does seem to be related to any particular statement, as we had skipped that test step, and then it hangs on the next step at the first statement.
Maybe you are looking for
-
i have just download a book from itunes store but, since i don't have an iPad, i can´t read it or even see it. Can anybody help me? Can i convert it? Thanks.
-
Cannot find symbol class Scanner
hi all i'm defining a class within a project so i can use the class inside my program, but the line: Scanner keyboard = new Scanner(System.in);generates an error with my compiler: cannot find symbol class Scanner please help
-
SCSI, AGP Powermac G4, and Tiger
I have a SCSI card installed in my AGP Graphics PowerMac G4, but it also has Tiger installed on it. I've read that the Mac OS X stopped supporting SCSI starting with Panther. Is this true? I have some SCSI external hard drives, and it would be nice i
-
Trackpad Issues with iMac Retina
Hello, I have noticed twice now that when I wake my iMac from sleep the trackpad malfunctions. I can move the curser but have lost all the other functions. I can click on things by physically pressing down on the trackpad, but the tap click option
-
How to I customize and save Apple Templates?
I need to scale down brochures to fit in my printer margins. Is there a way to permanently save these changes?