'Registration Timeout'
Hi,
I have posted this in the iPod Nano 2g forum but the problem may well be iTunes related so I hope you don't mind me posting here as well.
I have plugged in my new Nano and am getting a timeout message when I try to register the Nano. No matter what button I press ('Later', 'Never' or 'Continue') I get the same problem.
I have been told to try re-installing iTunes and then trying again - is this a case of downloading the latest version from the Apple website?
Any pointers gratefully received! Thanks.
iMac Intel Core 2 Duo 2.16 Ghz (20") Mac OS X (10.4.8)
Update - have downloaded the latest version of iTunes and re-installed. I have done a software update and rebooted. No change. Still can't use by lovely £130 Nano properly.
Does anybody from Apple ever read these forums because I don't seem to be the only person having this problem? I'll take my Nano into my nearest Apple Store and see what they say. Otherwise, I'm not sure what to do except ask for my money back.
iMac Intel Core 2 Duo 2.16 Ghz (20") Mac OS X (10.4.8)
Similar Messages
-
Sconadm timeout - Sun On-line Account authentication failed.
Hello,
I run Solaris 10 5/08 s10x_u5wos_10 X86.
and the registration timeout. See below the basicreg.log
I copy the commands i used. and the output. I also run the suc.sh script and post in the end.
#ping 82.98.86.176
82.98.86.176 is alive
#sconadm register -a -r regfile
sconadm is running
Authenticating user ...
Sun On-line Account authentication failed
failed registration!
telnet cns-transport.sun.com 443
Trying 198.232.168.137...
traceroute to cns-transport.sun.com (198.232.168.137), 30 hops max, 40 byte packets
1 172.30.168.254 (172.30.168.254) 0.409 ms 0.241 ms 0.147 ms
2 125-230-64-254.dynamic.hinet.net (125.230.64.254) 2.334 ms 77.107 ms 1.457 ms
3 tc-kk-t64-2.router.hinet.net (168.95.149.78) 0.937 ms 1.112 ms 0.867 ms
4 220-128-17-98.HINET-IP.hinet.net (220.128.17.98) 1.246 ms tc-c12r12.router.hinet.net (220.128.17.158) 1.252 ms 1.138 ms
5 tp-crs11.router.hinet.net (220.128.2.10) 4.423 ms 4.281 ms 15.803 ms
6 220-128-4-29.HINET-IP.hinet.net (220.128.4.29) 5.076 ms 4.274 ms 4.034 ms
7 r02-s2.tp.hinet.net (220.128.4.38) 16.038 ms 4.358 ms 4.359 ms
8 r12-pa.us.hinet.net (211.72.108.121) 142.842 ms 150.936 ms 142.567 ms
9 r11-pa.us.hinet.net (202.39.83.193) 143.152 ms 142.800 ms 142.830 ms
10 206.111.12.165.ptr.us.xo.net (206.111.12.165) 142.651 ms 142.925 ms 142.852 ms
11 te-11-0-0.rar3.sanjose-ca.us.xo.net (207.88.12.69) 144.081 ms 144.510 ms 144.974 ms
12 207.88.14.117.ptr.us.xo.net (207.88.14.117) 218.322 ms 218.461 ms 217.083 ms
13 207.88.14.118.ptr.us.xo.net (207.88.14.118) 218.363 ms 217.950 ms 218.103 ms
14 207.88.183.54.ptr.us.xo.net (207.88.183.54) 214.827 ms 214.479 ms 216.544 ms
15 border7.te2-2-bbnet2.wdc002.pnap.net (216.52.127.87) 214.862 ms 215.908 ms 214.832 ms
16 seven-6.border7.wdc002.pnap.net (216.52.125.250) 214.658 ms 214.440 ms 214.558 ms
17 * * *
18 * * *
# cat basicreg20081024111737681.log
24.10.2008 11:17:48 com.sun.cns.basicreg.BasicReg loadPropertiesFromHomeDir
INFO: properties file loaded from the default config.properties
24.10.2008 11:17:48 com.sun.scn.util.Utils getLocalHostNames
INFO: get hostname 82.98.86.176
24.10.2008 11:17:48 com.sun.scn.util.Utils getLocalHostNames
INFO: first returned hostname 82.98.86.176
24.10.2008 11:17:48 com.sun.cns.basicreg.cacao.NetworkProxyCacaoAdapter setProxy
INFO: SCNNetworkProxyConfigMBean.setHost() = null
24.10.2008 11:17:48 com.sun.cns.basicreg.cacao.NetworkProxyCacaoAdapter setProxy
INFO: SCNNetworkProxyConfigMBean.setPort() = null
24.10.2008 11:17:48 com.sun.cns.basicreg.cacao.NetworkProxyCacaoAdapter setProxy
INFO: SCNNetworkProxyConfigMBean.setUser() = null
24.10.2008 11:17:48 com.sun.cns.basicreg.cacao.NetworkProxyCacaoAdapter setProxy
INFO: SCNNetworkProxyConfigMBean.setPassword() = null
24.10.2008 11:17:48 com.sun.cns.basicreg.BasicRegCLI printRegistrationProfile
INFO: userName = [email protected]
24.10.2008 11:17:48 com.sun.cns.basicreg.BasicRegCLI printRegistrationProfile
INFO: password = *****
24.10.2008 11:17:48 com.sun.cns.basicreg.BasicRegCLI printRegistrationProfile
INFO: hostName =
24.10.2008 11:17:48 com.sun.cns.basicreg.BasicRegCLI printRegistrationProfile
INFO: portalEnabled =false
24.10.2008 11:17:48 com.sun.cns.basicreg.BasicRegCLI run
INFO: Authenticating user ...
24.10.2008 11:17:48 com.sun.cns.basicreg.cacao.ClientLoginCacaoAdapter getSCNClientSession
INFO: CREATING SCNClientSession
24.10.2008 11:25:18 com.sun.cns.basicreg.cacao.ClientLoginCacaoAdapter loginAccount
SCHWERWIEGEND: Error: login account exception: Connection refused to host: 82.98.86.176; nested exception is:
java.net.ConnectException: Connection timed out
24.10.2008 11:25:18 com.sun.cns.basicreg.cacao.ClientLoginCacaoAdapter loginAccount
SCHWERWIEGEND:
com.sun.scn.jmx.impl.UISClientLoginModule.login(UISClientLoginModule.java:151)
sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
java.lang.reflect.Method.invoke(Method.java:585)
javax.security.auth.login.LoginContext.invoke(LoginContext.java:769)
javax.security.auth.login.LoginContext.access$000(LoginContext.java:186)
javax.security.auth.login.LoginContext$5.run(LoginContext.java:706)
java.security.AccessController.doPrivileged(Native Method)
javax.security.auth.login.LoginContext.invokeCreatorPriv(LoginContext.java:703)
javax.security.auth.login.LoginContext.login(LoginContext.java:575)
com.sun.scn.jmx.impl.UISClientLogin.login(UISClientLogin.java:201)
sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
java.lang.reflect.Method.invoke(Method.java:585)
com.sun.jmx.mbeanserver.StandardMetaDataImpl.invoke(StandardMetaDataImpl.java:414)
javax.management.StandardMBean.invoke(StandardMBean.java:323)
com.sun.jmx.mbeanserver.DynamicMetaDataImpl.invoke(DynamicMetaDataImpl.java:213)
com.sun.jmx.mbeanserver.MetaDataImpl.invoke(MetaDataImpl.java:220)
com.sun.jmx.interceptor.DefaultMBeanServerInterceptor.invoke(DefaultMBeanServerInterceptor.java:815)
com.sun.jmx.mbeanserver.JmxMBeanServer.invoke(JmxMBeanServer.java:784)
com.sun.jdmk.interceptor.DefaultMBeanServerInterceptor.invoke(DefaultMBeanServerInterceptor.java:203)
com.sun.cacao.agent.DispatchInterceptor.invoke(DispatchInterceptor.java:736)
com.sun.cacao.agent.auth.impl.AccessControlInterceptor.invoke(AccessControlInterceptor.java:618)
com.sun.jdmk.JdmkMBeanServerImpl.invoke(JdmkMBeanServerImpl.java:764)
com.sun.cacao.common.instrum.impl.InstrumDefaultForwarder.invoke(InstrumDefaultForwarder.java:106)
javax.management.remote.rmi.RMIConnectionImpl.doOperation(RMIConnectionImpl.java:1410)
javax.management.remote.rmi.RMIConnectionImpl.access$100(RMIConnectionImpl.java:81)
javax.management.remote.rmi.RMIConnectionImpl$PrivilegedOperation.run(RMIConnectionImpl.java:1247)
java.security.AccessController.doPrivileged(Native Method)
javax.management.remote.rmi.RMIConnectionImpl.doPrivilegedOperation(RMIConnectionImpl.java:1350)
javax.management.remote.rmi.RMIConnectionImpl.invoke(RMIConnectionImpl.java:784)
sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
java.lang.reflect.Method.invoke(Method.java:585)
sun.rmi.server.UnicastServerRef.dispatch(UnicastServerRef.java:294)
sun.rmi.transport.Transport$1.run(Transport.java:153)
java.security.AccessController.doPrivileged(Native Method)
sun.rmi.transport.Transport.serviceCall(Transport.java:149)
sun.rmi.transport.tcp.TCPTransport.handleMessages(TCPTransport.java:466)
sun.rmi.transport.tcp.TCPTransport$ConnectionHandler.run(TCPTransport.java:707)
java.lang.Thread.run(Thread.java:595)
24.10.2008 11:25:18 com.sun.cns.basicreg.cacao.ClientLoginCacaoAdapter getLoginResult
INFO: SCN Fault: Connection refused to host: 82.98.86.176; nested exception is:
java.net.ConnectException: Connection timed out
24.10.2008 11:25:18 com.sun.cns.basicreg.BasicRegCLI run
SCHWERWIEGEND: Sun On-line Account authentication failed
#sh suc.sh
User: root
Logname: root
Freitag, 24. Oktober 2008 11:48 Uhr CST
xxx
smpatch settings:
patchpro.backout.directory - ""
patchpro.baseline.directory - /var/sadm/spool
patchpro.download.directory - /var/sadm/spool
patchpro.install.types - rebootafter:reconfigafter:standard
patchpro.patch.source - https://getupdates1.sun.com/
patchpro.patchset - current
patchpro.proxy.host - ""
patchpro.proxy.passwd **** ****
patchpro.proxy.port - 8080
patchpro.proxy.user - ""
smpatch analyze:
Failure: Cannot connect to retrieve detectors.jar: This system is currently unregistered and is unable to retrieve patches from the Sun Update Connection. Please register your system using the Update Manager, /usr/bin/updatemanager or provide valid Sun Online Account(SOA) credentials.
Sun UC patch revision:
120336-04
121082-06
121119-13
121454-02
123004-03
123006-07
123631-03
123896-04
124187-07
Solaris release:
Solaris 10 5/08 s10x_u5wos_10 X86
Copyright 2008 Sun Microsystems, Inc. All Rights Reserved.
Use is subject to license terms.
Assembled 24 March 2008
Solaris Kernel: Generic_127128-11
Machine Type: i86pc
Platform: i86pc
Java -version:
java version "1.5.0_14"
Java(TM) 2 Runtime Environment, Standard Edition (build 1.5.0_14-b03)
Java HotSpot(TM) Client VM (build 1.5.0_14-b03, mixed mode, sharing)
Cacao Java version:
java-home=/usr/jdk/jdk1.5.0_14
Software Cluster:
CLUSTER=SUNWCall
All ccr properties:
Property not defined: 18
18:
cns.assetid:
cns.br.SunUCenabled:
true
cns.ccr.keyGenPath:
/usr/lib/cc-ccr/bin/ccrKeyGen
cns.clientid:
cns.httpproxy.auth:
cns.httpproxy.ipaddr:
cns.httpproxy.port:
cns.regtoken:
cns.security.password:
cns.security.privatekey:
cns.security.publickey:
cns.swup.UMautolaunch:
false
cns.swup.autoAnalysis.enabled:
true
cns.swup.checkinInterval:
2
cns.swup.lastCheckin:
0
cns.swup.patchbaseline:
current
cns.swup.regRequired:
true
cns.transport.serverurl:
patchsvr not installed.
Sun UC package status:
SUNWbreg not installed
SUNWdc not installed
Edited by: Denis_Theinert on Oct 24, 2008 4:13 AMI could connect all of this hosts without problems.
# telnet sun.com 80
Trying 72.5.124.61...
Connected to sun.com.
Escape character is '^]'.
^CConnection to sun.com closed by foreign host.
# telnet cns-services.sun.com 443
Trying 198.232.168.133...
Connected to cns-services.sun.com.
Escape character is '^]'.
^CConnection to cns-services.sun.com closed by foreign host.
# telnet getupdates1.sun.com 443
Trying 198.232.168.136...
Connected to getupdates1.sun.com.
Escape character is '^]'.
^CConnection to getupdates1.sun.com closed by foreign host.
# telnet a248.e.akamai.net 443
Trying 60.254.154.75...
Connected to a248.e.akamai.net.
Escape character is '^]'.
^CConnection to a248.e.akamai.net closed by foreign host.
# -
Problem when applying IPSEC to DMVPN
Hi i have some trouble with DMVPN
i configured NHRP between a HUB and aSPOKE:
HUB
tu0 tu1
| |
ISP
|
tu0,tu1
SPOKE
the HUB has two physical interfaces and two logical interfaces.
The SPOKE has one physical interface and two logical interfaces.
in configured NHRP correctly, the tunnels are detected in the HUB and the SPOKE.
when i add the profile IPSEC to the intefaces i lose tunnel1.
SPOKE1#sh ip nhrp
10.1.1.4/32 via 10.1.1.4, Tunnel0 created 02:22:01, never expire
Type: static, Flags: authoritative used
NBMA address: 190.1.1.1
10.2.2.4/32 via 10.2.2.4, Tunnel1 created 02:18:21, never expire
Type: static, Flags: authoritative used
NBMA address: 190.1.2.1
SPOKE1#debug ip nhrp
tunnel0
*Mar 1 03:50:09.399: NHRP: Attempting to send packet via DEST 10.1.1.4
*Mar 1 03:50:09.399: NHRP: Encapsulation succeeded. Tunnel IP addr 190.1.1.1
*Mar 1 03:50:09.399: NHRP: Send Registration Request via Tunnel0 vrf 0, packet size: 82
*Mar 1 03:50:09.403: src: 10.1.1.1, dst: 10.1.1.4
*Mar 1 03:50:09.403: NHRP: 82 bytes out Tunnel0
*Mar 1 03:50:09.519: NHRP: Receive Registration Reply via Tunnel0 vrf 0, packet size: 102
*Mar 1 03:50:09.519: NHRP: netid_in = 0, to_us = 1
tunnel 1
*Mar 1 03:50:30.575: NHRP: Attempting to send packet via DEST 10.2.2.4
*Mar 1 03:50:30.575: NHRP: Encapsulation succeeded. Tunnel IP addr 190.1.2.1
*Mar 1 03:50:30.575: NHRP: Send Registration Request via Tunnel1 vrf 0, packet size: 82
*Mar 1 03:50:30.579: src: 10.2.2.1, dst: 10.2.2.4
*Mar 1 03:50:30.579: NHRP: 82 bytes out Tunnel1
*Mar 1 03:50:30.579: NHRP: Resetting retransmit due to hold-timer for 10.2.2.4
no reply from the HUB.
HUB#sh ip nhrp
10.1.1.1/32 via 10.1.1.1, Tunnel0 created 00:05:05, expire 00:08:29
Type: dynamic, Flags: authoritative unique registered
NBMA address: 191.1.1.11
just tunnel0 is there !
i have also this on the HUB :
*Mar 1 03:58:54.519: %CRYPTO-6-IKMP_MODE_FAILURE: Processing of Quick mode failed with peer at 191.1.1.11 (physical adress of SPOKE1)
configs :
HUB :
crypto isakmp policy 10
encr aes
hash md5
authentication pre-share
group 2
crypto isakmp key techservices address 0.0.0.0 0.0.0.0
crypto ipsec transform-set AES_MD5 esp-aes esp-md5-hmac
crypto ipsec profile DMVPN
set transform-set AES_MD5
interface Tunnel0
bandwidth 10000
ip address 10.1.1.4 255.255.255.0
no ip redirects
ip mtu 1400
no ip next-hop-self eigrp 123
ip nhrp authentication dmvpn1
ip nhrp map multicast dynamic
ip nhrp network-id 123
no ip split-horizon eigrp 123
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 123
tunnel protection ipsec profile DMVPN
interface Tunnel1
bandwidth 10000
ip address 10.2.2.4 255.255.255.0
no ip redirects
ip mtu 1400
no ip next-hop-self eigrp 124
ip nhrp authentication dmvpn2
ip nhrp map multicast dynamic
ip nhrp network-id 124
no ip split-horizon eigrp 124
tunnel source FastEthernet1/0
tunnel mode gre multipoint
tunnel key 124
tunnel protection ipsec profile DMVPN
router eigrp 123
network 10.1.1.0 0.0.0.255
network 172.16.4.0 0.0.0.255
no auto-summary
router eigrp 124
network 10.2.2.0 0.0.0.255
network 172.16.4.0 0.0.0.255
no auto-summary
SPOKE1:
crypto isakmp policy 10
encr aes
hash md5
authentication pre-share
group 2
crypto isakmp key techservices address 0.0.0.0 0.0.0.0
crypto ipsec transform-set AES_MD5 esp-aes esp-md5-hmac
crypto ipsec profile DMVPN
set transform-set AES_MD5
interface Tunnel0
bandwidth 10000
ip address 10.1.1.1 255.255.255.0
ip mtu 1400
ip nhrp authentication dmvpn1
ip nhrp map multicast 190.1.1.1
ip nhrp map 10.1.1.4 190.1.1.1
ip nhrp network-id 123
ip nhrp holdtime 600
ip nhrp nhs 10.1.1.4
ip nhrp registration timeout 300
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 123
tunnel protection ipsec profile DMVPN
interface Tunnel1
bandwidth 10000
ip address 10.2.2.1 255.255.255.0
ip mtu 1400
ip nhrp authentication dmvpn2
ip nhrp map multicast 190.1.2.1
ip nhrp map 10.2.2.4 190.1.2.1
ip nhrp network-id 124
ip nhrp holdtime 600
ip nhrp nhs 10.2.2.4
ip nhrp registration timeout 300
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 124
tunnel protection ipsec profile DMVPN
router eigrp 123
network 10.1.1.0 0.0.0.255
network 172.16.1.0 0.0.0.255
no auto-summary
router eigrp 124
network 10.2.2.0 0.0.0.255
network 172.16.1.0 0.0.0.255
no auto-summary
regardsbut when i add an other SPOKE there is a problem :
HUB
| |
SPOKE1___ ISP__SPOKE2
HUB:
crypto isakmp policy 10
encr aes
hash md5
authentication pre-share
group 2
crypto isakmp key cisco address 0.0.0.0 0.0.0.0
crypto ipsec transform-set AES_MD5 esp-aes esp-md5-hmac
crypto ipsec profile DMVPN
set transform-set AES_MD5
interface Tunnel0
bandwidth 1000
ip address 10.1.1.4 255.255.255.0
no ip redirects
ip mtu 1400
no ip next-hop-self eigrp 123
ip nhrp authentication dmvpn1
ip nhrp map multicast dynamic
ip nhrp network-id 123
no ip split-horizon eigrp 123
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 123
tunnel protection ipsec profile DMVPN
interface Tunnel1
bandwidth 1000
ip address 10.2.2.4 255.255.255.0
no ip redirects
ip mtu 1400
no ip next-hop-self eigrp 124
ip nhrp authentication dmvpn2
ip nhrp map multicast dynamic
ip nhrp network-id 124
no ip split-horizon eigrp 124
tunnel source FastEthernet1/0
tunnel mode gre multipoint
tunnel key 124
tunnel protection ipsec profile DMVPN
router eigrp 123
network 10.1.1.0 0.0.0.255
network 172.16.4.0 0.0.0.255
no auto-summary
router eigrp 124
network 10.2.2.0 0.0.0.255
network 172.16.4.0 0.0.0.255
no auto-summary
SPOKE1 :
crypto isakmp policy 10
encr aes
hash md5
authentication pre-share
group 2
crypto isakmp key cisco address 0.0.0.0 0.0.0.0
crypto ipsec transform-set AES_MD5 esp-aes esp-md5-hmac
crypto ipsec profile DMVPN
set transform-set AES_MD5
interface Tunnel0
bandwidth 1000
ip address 10.1.1.1 255.255.255.0
no ip redirects
ip mtu 1400
ip nhrp authentication dmvpn1
ip nhrp map multicast 190.1.1.1
ip nhrp map 10.1.1.4 190.1.1.1
ip nhrp network-id 123
ip nhrp holdtime 600
ip nhrp nhs 10.1.1.4
ip nhrp registration timeout 300
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 123
tunnel protection ipsec profile DMVPN shared
interface Tunnel1
bandwidth 1000
ip address 10.2.2.1 255.255.255.0
no ip redirects
ip mtu 1400
ip nhrp authentication dmvpn2
ip nhrp map multicast 190.1.2.1
ip nhrp map 10.2.2.4 190.1.2.1
ip nhrp network-id 124
ip nhrp holdtime 600
ip nhrp nhs 10.2.2.4
ip nhrp registration timeout 300
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 124
tunnel protection ipsec profile DMVPN shared
router eigrp 123
network 10.1.1.0 0.0.0.255
network 172.16.1.0 0.0.0.255
no auto-summary
router eigrp 124
network 10.2.2.0 0.0.0.255
network 172.16.1.0 0.0.0.255
no auto-summary
SPOKE2 :
crypto isakmp policy 10
encr aes
hash md5
authentication pre-share
group 2
crypto isakmp key cisco address 0.0.0.0 0.0.0.0
crypto ipsec transform-set AES_MD5 esp-aes esp-md5-hmac
crypto ipsec profile DMVPN
set transform-set AES_MD5
interface Tunnel0
bandwidth 1000
ip address 10.1.1.2 255.255.255.0
no ip redirects
ip mtu 1400
ip nhrp authentication dmvpn1
ip nhrp map multicast 190.1.1.1
ip nhrp map 10.1.1.4 190.1.1.1
ip nhrp network-id 123
ip nhrp holdtime 600
ip nhrp nhs 10.1.1.4
ip nhrp registration timeout 300
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 123
tunnel protection ipsec profile DMVPN shared
interface Tunnel1
bandwidth 1000
ip address 10.2.2.2 255.255.255.0
no ip redirects
ip mtu 1400
ip nhrp authentication dmvpn2
ip nhrp map multicast 190.1.2.1
ip nhrp map 10.2.2.4 190.1.2.1
ip nhrp network-id 124
ip nhrp holdtime 600
ip nhrp nhs 10.2.2.4
ip nhrp registration timeout 300
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 124
tunnel protection ipsec profile DMVPN shared
router eigrp 123
network 10.1.1.0 0.0.0.255
network 172.16.2.0 0.0.0.255
no auto-summary
router eigrp 124
network 10.2.2.0 0.0.0.255
network 172.16.2.0 0.0.0.255
no auto-summary
HUB:
HUB#sh ip nhrp
10.1.1.1/32 via 10.1.1.1, Tunnel0 created 00:15:17, expire 00:09:21
Type: dynamic, Flags: authoritative unique registered
NBMA address: 191.1.1.11
10.1.1.2/32 via 10.1.1.2, Tunnel0 created 00:12:09, expire 00:07:50
Type: dynamic, Flags: authoritative unique registered
NBMA address: 191.1.1.12
10.2.2.1/32, Tunnel1 created 00:02:57, expire 00:00:07
Type: incomplete, Flags: negative
Cache hits: 7
10.2.2.2/32 via 10.2.2.2, Tunnel1 created 00:12:00, expire 00:07:58
Type: dynamic, Flags: authoritative unique registered
NBMA address: 191.1.1.12
HUB can't have the NBMA adress for 10.2.2.1 for SPOKE1
HUB#ping 10.2.2.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.2.2.1, timeout is 2 seconds:
Success rate is 0 percent (0/5)
*Mar 1 00:45:18.431: NHRP: MACADDR: if_in null netid-in 0 if_out Tunnel1 netid-out 124
*Mar 1 00:45:18.435: NHRP: Checking for delayed event 0.0.0.0/10.2.2.1 on list (Tunnel1).
*Mar 1 00:45:18.435: NHRP: No node found..
*Mar 1 00:45:07.131: NHRP: MACADDR: if_in null netid-in 0 if_out Tunnel1 netid-out 124
*Mar 1 00:45:07.131: NHRP: Checking for delayed event 0.0.0.0/10.2.2.1 on list (Tunnel1).
*Mar 1 00:48:30.759: NHRP: Checking for delayed event 0.0.0.0/10.2.2.1 on list (Tunnel1).
*Mar 1 00:48:30.763: NHRP: No node found.
*Mar 1 00:48:30.763: NHRP: Attempting to send packet via DEST 10.2.2.1
*Mar 1 00:48:30.767: NHRP: Send Resolution Request via Tunnel1 vrf 0, packet size: 82
*Mar 1 00:48:30.771: src: 10.2.2.4, dst: 10.2.2.1
*Mar 1 00:48:30.771: NHRP: Encapsulation failed for destination 10.2.2.1 out Tunnel1
SPOKE1#
*Mar 1 00:53:38.695: NHRP: Setting retrans delay to 64 for nhs dst 10.2.2.4
*Mar 1 00:53:38.699: NHRP: Attempting to send packet via DEST 10.2.2.4
*Mar 1 00:53:38.699: NHRP: Encapsulation succeeded. Tunnel IP addr 190.1.2.1
*Mar 1 00:53:38.703: NHRP: Send Registration Request via Tunnel1 vrf 0, packet size: 82
*Mar 1 00:53:38.711: src: 10.2.2.1, dst: 10.2.2.4
*Mar 1 00:53:38.715: NHRP: 82 bytes out Tunnel1
no reply from the HUB
SPOKE1#ping 10.2.2.4
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.2.2.4, timeout is 2 seconds:
Success rate is 0 percent (0/5)
the SPOKE can't reach 10.2.2.4
after a few time :
HUB#sh ip nhrp
10.1.1.1/32 via 10.1.1.1, Tunnel0 created 00:25:03, expire 00:09:35
Type: dynamic, Flags: authoritative unique registered used
NBMA address: 191.1.1.11
10.1.1.2/32 via 10.1.1.2, Tunnel0 created 00:21:55, expire 00:08:03
Type: dynamic, Flags: authoritative unique registered
NBMA address: 191.1.1.12
10.2.2.2/32 via 10.2.2.2, Tunnel1 created 00:21:47, expire 00:08:12
Type: dynamic, Flags: authoritative unique registered
NBMA address: 191.1.1.12
only 3 tunnels -
Hello All,
I am trying to build a DMVPN solution for two sites each with secondary ISPs.
The solution works "sort of", but doesn't seem very robust (sometimes a router reload is required if VPN doesn't come up after ISP failover)
I was wondering if anyone had any suggestions to my config below?
Thanks!
!!!!HUB!!!!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot-end-marker!no logging console!no aaa new-modelmemory-size iomem 5!!ip cef!!crypto isakmp policy 3 hash md5 authentication pre-sharecrypto isakmp key cisco123 address 0.0.0.0 0.0.0.0!!crypto ipsec transform-set strong esp-3des esp-md5-hmac!crypto ipsec profile dmvpn set security-association lifetime seconds 1800 set transform-set aes256 set pfs group5!crypto ipsec profile dmvpn2 set security-association lifetime seconds 1800 set transform-set aes256 set pfs group5!!interface Tunnel0 ip address 10.255.255.1 255.255.255.0 no ip redirects ip mtu 1400 no ip next-hop-self eigrp 53 no ip split-horizon eigrp 53 ip nhrp authentication secret1 ip nhrp map multicast dynamic ip nhrp network-id 6 ip nhrp holdtime 300 ip tcp adjust-mss 1360 delay 1000 tunnel source GigabitEthernet0/1 tunnel mode gre multipoint tunnel key 545 tunnel protection ipsec profile dmvpn shared!interface Tunnel1 ip address 10.255.254.1 255.255.255.0 no ip redirects ip mtu 1400 no ip next-hop-self eigrp 53 no ip split-horizon eigrp 53 ip nhrp authentication secret1 ip nhrp map multicast dynamic ip nhrp network-id 7 ip nhrp holdtime 300 ip tcp adjust-mss 1360 delay 1000 tunnel source FastEthernet0/0/0 tunnel mode gre multipoint tunnel key 546 tunnel protection ipsec profile dmvpn2 shared!interface Tunnel2 ip address 10.255.253.1 255.255.255.0 no ip redirects ip mtu 1400 no ip next-hop-self eigrp 53 no ip split-horizon eigrp 53 ip nhrp authentication secret1 ip nhrp map multicast dynamic ip nhrp network-id 8 ip nhrp holdtime 300 ip tcp adjust-mss 1360 delay 1000 tunnel source GigabitEthernet0/1 tunnel mode gre multipoint tunnel key 547 tunnel protection ipsec profile dmvpn shared!interface Tunnel3 ip address 10.255.252.1 255.255.255.0 no ip redirects ip mtu 1400 no ip next-hop-self eigrp 53 no ip split-horizon eigrp 53 ip nhrp authentication secret1 ip nhrp map multicast dynamic ip nhrp network-id 9 ip nhrp holdtime 300 ip tcp adjust-mss 1360 delay 1000 tunnel source FastEthernet0/0/0 tunnel mode gre multipoint tunnel key 548 tunnel protection ipsec profile dmvpn2 shared!interface FastEthernet0/0/0 description Secondary ISP ip address 199.1.1.1 255.255.255.0 duplex auto speed auto!interface VLAN1 description LAN ip address 192.168.1.1 255.255.255.0!interface GigabitEthernet0/1 description Primary ISP ip address 200.1.1.1 255.255.255.0 duplex auto speed auto!router eigrp 53 network 10.255.252.0 0.0.0.255 network 10.255.253.0 0.0.0.255 network 10.255.254.0 0.0.0.255 network 10.255.255.0 0.0.0.255 network 192.168.1.0 eigrp stub connected no auto-summary!!ip route 0.0.0.0 0.0.0.0 199.1.1.2 5ip route 0.0.0.0 0.0.0.0 200.1.1.2 !!control-plane!line con 0line aux 0line vty 0 4 login!!end
!!!SPOKE!!!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot-end-marker!no logging console!no aaa new-modelmemory-size iomem 5!!ip cef!!crypto isakmp policy 3 hash md5 authentication pre-sharecrypto isakmp key cisco123 address 0.0.0.0 0.0.0.0!!crypto ipsec transform-set strong esp-3des esp-md5-hmac!crypto ipsec profile dmvpn set security-association lifetime seconds 1800 set transform-set aes256 set pfs group5!crypto ipsec profile dmvpn2 set security-association lifetime seconds 1800 set transform-set aes256 set pfs group5!!!interface VLAN1 ip address 192.168.0.1 255.255.255.0 no ip redirects!interface Tunnel0 ip address 10.255.255.5 255.255.255.0 no ip redirects ip mtu 1400 ip nhrp authentication secret1 ip nhrp map 10.255.255.1 200.1.1.1 ip nhrp map multicast 200.1.1.1 ip nhrp network-id 6 ip nhrp holdtime 300 ip nhrp nhs 10.255.255.1 ip nhrp registration timeout 30 delay 1000 tunnel source GigabitEthernet0/1 tunnel mode gre multipoint tunnel key 545 tunnel protection ipsec profile dmvpn shared!interface Tunnel1 ip address 10.255.254.5 255.255.255.0 no ip redirects ip mtu 1440 ip nhrp authentication secret1 ip nhrp map 10.255.254.1 199.1.1.1 ip nhrp map multicast 199.1.1.1 ip nhrp network-id 7 ip nhrp holdtime 300 ip nhrp nhs 10.255.254.1 delay 1500 tunnel source GigabitEthernet0/1 tunnel mode gre multipoint tunnel key 546 tunnel protection ipsec profile dmvpn shared!interface Tunnel2 ip address 10.255.253.5 255.255.255.0 no ip redirects ip mtu 1400 ip nhrp authentication secret1 ip nhrp map multicast 200.1.1.1 ip nhrp map 10.255.253.1 200.1.1.1 ip nhrp network-id 8 ip nhrp holdtime 300 ip nhrp nhs 10.255.253.1 ip nhrp registration timeout 30 delay 1000 tunnel source FastEthernet0/0/0 tunnel mode gre multipoint tunnel key 547 tunnel protection ipsec profile dmvpn2 shared!interface Tunnel3 ip address 10.255.252.5 255.255.255.0 no ip redirects ip mtu 1440 ip nhrp authentication secret1 ip nhrp map multicast 199.1.1.1 ip nhrp map 10.255.252.1 199.1.1.1 ip nhrp network-id 9 ip nhrp holdtime 300 ip nhrp nhs 10.255.252.1 delay 1500 tunnel source FastEthernet0/0/0 tunnel mode gre multipoint tunnel key 548 tunnel protection ipsec profile dmvpn2 shared!interface FastEthernet0/0/0description Secondary Internet ip address 201.1.1.1 255.255.255.0 duplex auto speed auto!interface GigabitEthernet0/1 description Primary Internet ip address 201.2.2.1 255.255.255.0 duplex auto speed auto!router eigrp 53 distribute-list 1 out network 10.255.252.0 0.0.0.255 network 10.255.253.0 0.0.0.255 network 10.255.254.0 0.0.0.255 network 10.255.255.0 0.0.0.255 network 192.168.0.0 offset-list 1 out 12800 Tunnel1 eigrp stub connected no auto-summary!!ip route 0.0.0.0 0.0.0.0 201.2.2.2ip route 0.0.0.0 0.0.0.0 201.1.1.2 5!!access-list 1 permit 192.168.0.0access-list 1 permit 10.255.255.0 0.0.0.255access-list 1 permit 10.255.254.0 0.0.0.255access-list 1 permit 10.255.253.0 0.0.0.255access-list 1 permit 10.255.252.0 0.0.0.255!!control-plane!!line con 0line aux 0line vty 0 4 login!!endHello,
Thanks for the response!
I left the stub on the hub while troubleshooting, it has since been removed.
By DPD, do you mean "crypto isakmp keepalive 10 periodic"?
I've since added that (spoke and hub) and while the tunnels work great (they fail over, can ping 10.255.25x.x) the routes do not update which lead me to believe it's an EIGRP problem. Is there something else I should do for DPD?
Thanks again
Will
Can't edit the original post, so:
!Hub
crypto isakmp keepalive 10 periodic
router eigrp 53
network 10.255.252.0 0.0.0.255
network 10.255.253.0 0.0.0.255
network 10.255.254.0 0.0.0.255
network 10.255.255.0 0.0.0.255
network 192.168.1.0
no auto-summary
!Spoke
crypto isakmp keepalive 10 periodic
router eigrp 53
network 10.255.252.0 0.0.0.255
network 10.255.253.0 0.0.0.255
network 10.255.254.0 0.0.0.255
network 10.255.255.0 0.0.0.255
network 192.168.0.0
eigrp stub connected
no auto-summary -
I have problem with a dynamic failover with two isps
Hello, I would like to help me with something.
I would like to do failover on my cisco router but the problem is that i have two isp but one of them is DSL. I meam that It learns gateway for dhcp and this is my main gateway.
I tried to do the same thing but I can´t put track in this command "ip route 0.0.0.0 0.0.0.0 dhcp.."
I also use "ip dhcp-client default-route 25" but It didn´t work..
could you help me ? please
I upload a file with configuration that i actually have it. In this file I don´t have any configuration about failover because i tried many option but i haven´t found any solutionI did this but on router didn´t change deafult route.
This is the configuration that i tried:
Current configuration : 9940 bytes
! Last configuration change at 22:10:41 UTC Fri Aug 29 2014 by Conssa
version 15.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname RT_Conssaccs
boot-start-marker
boot system flash:c890-universalk9-mz.153-3.M2.bin
boot-end-marker
aqm-register-fnf
logging buffered 51200 warnings
enable secret 5 $1$RK//$OFh6Dnk96LlX1VFKQwsme.
aaa new-model
aaa authentication login default enable
aaa authentication login consola local
aaa authentication login vty line
aaa authentication login userauthen local
aaa authorization network EZAUTHR local
aaa session-id common
crypto pki trustpoint TP-self-signed-4275920401
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-4275920401
revocation-check none
rsakeypair TP-self-signed-4275920401
ip dhcp ping timeout 100
ip dhcp update dns
ip dhcp-client default-router distance 100
ip cef
no ipv6 cef
multilink bundle-name authenticated
license udi pid CISCO891-K9 sn FTX145104B5
object-group network conssaremoto
description vpnremoto
range
object-group network pruebasael
description vpnremoto
range
redundancy
track 1 ip sla 1 reachability
no ip ftp passive
crypto isakmp policy 10
encr 3des
authentication pre-share
group 5
lifetime 180
crypto isakmp policy 20
encr 3des
hash md5
authentication pre-share
group 2
lifetime 28800
crypto isakmp key cisco address
crypto isakmp keepalive 10 4
crypto isakmp client configuration group conssa
key vpnbna
pool conssaVPN
acl 121
mode transport
crypto ipsec transform-set TSET esp-3des esp-md5-hmac
mode tunnel
crypto ipsec profile CiscoCP_Profile1
set transform-set ESP-3DES-SHA
set pfs group5
crypto ipsec profile EZPROFILE
set transform-set TSET
interface Tunnel0
description VPNConssaCCs
bandwidth 1000
ip address
ip mask-reply
ip mtu
ip nhrp authentication DMVPN_NW
ip nhrp map multicast
ip nhrp map
ip nhrp network-id 100000
ip nhrp holdtime 360
ip nhrp nhs
ip nhrp registration no-unique
ip nhrp registration timeout 30
ip tcp adjust-mss 1360
delay 1000
tunnel source GigabitEthernet0
tunnel destination
tunnel key 100000
tunnel protection ipsec profile CiscoCP_Profile1
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
switchport access vlan 2
no ip address
shutdown
interface FastEthernet3
no ip address
interface FastEthernet4
no ip address
interface FastEthernet5
no ip address
interface FastEthernet6
no ip address
interface FastEthernet7
no ip address
interface FastEthernet8
description $ETH-WAN$
no ip address
shutdown
duplex auto
speed auto
interface Virtual-Template1 type tunnel
ip unnumbered Vlan1
tunnel mode ipsec ipv4
tunnel protection ipsec profile EZPROFILE
interface GigabitEthernet0
description $ETH-WAN$
ip dhcp client route track 1
ip ddns update hostname
ip ddns update noip
ip address dhcp
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface Vlan1
description $ETH-LAN$
ip address
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface Vlan2
no ip address
shutdown
interface Async1
no ip address
encapsulation slip
ip local policy route-map prueba
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http client username conssa
ip nat inside source list 1 interface GigabitEthernet0 overload
ip route 0.0.0.0 0.0.0.0 10.10.6.1 200
ip sla auto discovery
ip sla 1
icmp-echo 8.8.8.8 source-interface GigabitEthernet0
frequency 5
ip sla schedule 1 life forever start-time now
no logging trap
no cdp run
route-map prueba permit 10
match ip address 101
set ip next-hop dynamic dhcp
access-list 1 permit any
access-list 101 permit icmp any host 8.8.8.8 echo
sh ip route
Gateway of last resort is 200.84.32.1 to network 0.0.0.0
S* 0.0.0.0/0 [100/0] via 200.84.32.1
10.0.0.0/8 is variably subnetted, 3 subnets, 3 masks -
Omni Portlet shows No Listener
We have Portal 10.1.4. When connection to portal are reached at 120 then omni portlet on every page of portal shows "No Listener". Other content still visisble on the pages, only problem with the omni portlets.
What should i do to solve the issue.
Thanks in advanceSolutions is to increase timeout value in provider.xml file in MID_TIER_ORACLE_HOME/j2ee/OC4J_Portal/applications/portalTools/omniPortlet/WEB-INF/providers/omniPortlet. If you change the timeout value, you also need to do the following:
Bounce your middle-tier.
Increase the provider registration Timeout value of the OracleAS Portal instances with which this provider is registered. -
About configuration in ubr7200 of CMTS
Hi......
The shown configuraion is ubr7200 CMTS router.
I would like to know each command statement.
Would you explanation me next config ?
I wanna easy explanation. :)
interface Cable2/0
ip address 10.80.0.1 255.255.254.0 secondary
ip address 58.145.127.65 255.255.255.192 secondary
ip address 10.64.0.1 255.255.224.0
ip access-group 104 in
ip pim dense-mode
no ip mroute-cache
no keepalive
cable registration-timeout 30
cable bundle 10 master
cable downstream rate-limit token-bucket shaping
cable downstream annex B
cable downstream modulation 256qam
cable downstream interleave-depth 32
cable downstream frequency 555000000
cable upstream 0 frequency 26000000
cable upstream 0 power-level 10
cable upstream 0 channel-width 3200000
no cable upstream 0 shutdown
cable upstream 1 frequency 31008000
cable upstream 1 power-level 10
cable upstream 1 channel-width 3200000
no cable upstream 1 shutdown
cable upstream 2 frequency 31008000
cable upstream 2 power-level 10
cable upstream 2 channel-width 3200000
no cable upstream 2 shutdown
cable upstream 3 frequency 26000000
cable upstream 3 power-level 10
cable upstream 3 channel-width 3200000
no cable upstream 3 shutdown
cable upstream 4 frequency 26000000
cable upstream 4 power-level 10
cable upstream 4 channel-width 3200000
no cable upstream 4 shutdown
cable upstream 5 frequency 26000000
cable upstream 5 power-level 10
cable upstream 5 channel-width 3200000
no cable upstream 5 shutdown
no cable ip-multicast-echo
cable dhcp-giaddr policy
cable helper-address 61.102.191.20
I wait your answer.......
Thanks.....After you have completed upstream and downstream configuration in Chapter 2, "Configuring the Cable Modem Termination System for the First Time,"you have additional options to manage how your cable modems (CMs) operate in the hybrid fiber-coaxial (HFC) network. You can set the following CM functions:
http://www.cisco.com/en/US/products/hw/cable/ps2217/products_configuration_guide_chapter09186a00801170f2.html
http://www.cisco.com/en/US/tech/tk86/tk804/technologies_q_and_a_item09186a00800a4ae5.shtml -
EAZYVPN and DMVPN on the same router,same interface
Hi all,
First of all, thanks in advance for the help. I have setup DMVPN and EAZYVPN on one router. Tunnel interface on Spoke one and Spoke two are up/up and show crypto ISakmp sa shows both tunnels are in idle. However, tunnel to Spoke one(10.10.1.1) keep bouncing on and off(see below). Every 30 sec or so, the tunnel gone back to IKE phase while tunnel for spoke two(5.5.5.1) still leave active. THe configuration on the HUB side is the same for both spoke!! show crypto ipsec sec shows both side has the same life time(IOS default). Could that be an IOS debug on the spoke one?
Hub :
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 15.1(3)T2, RELEASE SOFTWARE (fc1)
HUB#sh crypto ipsec security-association
Security association lifetime: 4608000 kilobytes/3600 seconds
Spoke one:
Cisco IOS Software, C2600 Software (C2600-ADVSECURITYK9-M), Version 12.4(8), RELEASE SOFTWARE (fc1)
SPOKE1#sh crypto ipsec security-association
Security association lifetime: 4608000 kilobytes/3600 seconds
HUB#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id status
5.5.5.1 5.5.5.2 QM_IDLE 1002 ACTIVE
10.10.1.1 10.10.1.2 MM_NO_STATE 1134 ACTIVE (deleted)
10.10.1.1 1.1.1.10 QM_IDLE 1126 ACTIVE
10.10.1.1 1.1.1.10 QM_IDLE 1076 ACTIVE
HUB#sh crypto se
HUB#sh crypto session
Crypto session current status
Interface: Serial0/1/1
Username: testuser
Profile: AccountingPro
Group: Accounting
Assigned address: 20.20.20.1
Session status: UP-ACTIVE
Peer: 1.1.1.10 port 60201
IKEv1 SA: local 10.10.1.1/500 remote 1.1.1.10/60201 Active
IPSEC FLOW: permit ip 0.0.0.0/0.0.0.0 host 20.20.20.1
Active SAs: 2, origin: dynamic crypto map
Interface: Serial0/1/1
Username: testuser
Profile: AccountingPro
Group: Accounting
Assigned address: 20.20.20.2
Session status: UP-ACTIVE
Peer: 1.1.1.10 port 49768
IKEv1 SA: local 10.10.1.1/500 remote 1.1.1.10/49768 Active
IPSEC FLOW: permit ip 0.0.0.0/0.0.0.0 host 20.20.20.2
Active SAs: 2, origin: dynamic crypto map
Interface: FastEthernet0/1
Profile: DMVPN
Session status: UP-IDLE
Peer: 5.5.5.2 port 500
IKEv1 SA: local 5.5.5.1/500 remote 5.5.5.2/500 Active
Interface: Serial0/1/1
Profile: DMVPN
Session status: DOWN-NEGOTIATING
Peer: 10.10.1.2 port 500
IKEv1 SA: local 10.10.1.1/500 remote 10.10.1.2/500 Inactive
HUB#
2. My second issue is, I use the same interface(s0/1/1=10.10.1.1) for eazyvpn access. The client from eazyvpn is connected fine,but does not receive traffric back(statics window show no decrypted=0 and reeiced=0). The eazy vpn can't even ping the IP address assigned to the vpn client(20.20.20.2), and the client can only pin 10.10.1.1 address. Reverse router is able but the 20.20.20.0/24 network didn't show up in the ip table of the HUB router!!!
DMVPN AND EAZYVPN SERVER config..
crypto keyring dmvpnkey
pre-shared-key address 0.0.0.0 0.0.0.0 key DMVPNLAB
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
crypto isakmp policy 20
encr aes
authentication pre-share
group 2
crypto isakmp policy 30
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp policy 40
authentication pre-share
crypto isakmp keepalive 30
crypto isakmp xauth timeout 90
crypto isakmp client configuration group Accounting
key eazypvn
dns 4.2.2.2
wins 4.2.2.2
domain bigBois.com
pool dmAccouting
crypto isakmp profile AccountingPro
match identity group Accounting
client authentication list access_in
isakmp authorization list my_vpn
client configuration address respond
crypto isakmp profile DMVPN
keyring dmvpnkey
match identity address 0.0.0.0
crypto ipsec transform-set DMVPN ah-sha-hmac esp-aes
mode transport
crypto ipsec transform-set EAZYVPN esp-3des esp-md5-hmac
crypto ipsec profile dmvpnlab
set transform-set DMVPN
set isakmp-profile AccountingPro
crypto dynamic-map Remote_Acc 20
set transform-set EAZYVPN
set isakmp-profile AccountingPro
reverse-route
crypto map RemoteAcc client authentication list access_in
crypto map Remote_Acc client authentication list my_vpn
crypto map Remote_Acc 20 ipsec-isakmp dynamic Remote_Acc
interface Loopback0
ip address 192.168.200.1 255.255.255.0
interface Loopback2
ip address 172.16.10.1 255.255.255.0
interface Loopback3
ip address 172.16.15.1 255.255.255.0
interface Tunnel1
bandwidth 10000
ip address 4.4.4.1 255.255.255.0
no ip redirects
ip mtu 1400
no ip next-hop-self eigrp 10
ip nhrp authentication DMVPN
ip nhrp map multicast dynamic
ip nhrp network-id 7940
ip nhrp registration timeout 10
ip tcp adjust-mss 1360
tunnel source Serial0/1/1
tunnel mode gre multipoint
tunnel key 7940
tunnel protection ipsec profile dmvpnlab
interface FastEthernet0/0
description OUTSIDE
ip address 1.1.1.1 255.255.255.0
ip virtual-reassembly in
duplex auto
speed auto
interface FastEthernet0/1
description INSIDE
ip address 5.5.5.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface Serial0/1/0
no ip address
shutdown
clock rate 2000000
interface Serial0/1/1
description to SPOKE1
ip address 10.10.1.1 255.255.255.0
crypto map Remote_Acc
interface Serial0/3/0
no ip address
shutdown
router eigrp 10
network 4.4.4.0 0.0.0.255
network 5.5.5.0 0.0.0.255
network 10.0.0.0
network 10.10.10.0 0.0.0.3
network 172.16.0.0 0.0.0.255
network 172.16.1.0 0.0.0.255
network 172.16.10.0 0.0.0.255
network 172.16.15.0 0.0.0.255
network 192.168.200.0
ip local pool dmAccouting 20.20.20.1 20.20.20.10
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
THanks a bunch for the help,
ErnestAny ideas why devices keep renewing phase 1?
Thanks, -
DMVPN GRE with IPSEC fragmentation
When configuring our tunnel we get an error message indicating that the MTU is greater than the transport value 1376, fragmentation will occur (see below). We are using transport mode and using the recommended MTU settings of 1400 bytes. Could this be causing excessive fragmentation and affecting latency and user experience?
ro1-91309(config)#interface Tunnel2
service_policy on dynamic interface is not allowed if there is fair-queue configured on main interface
ro1-91309(config-if)# description GRE tunnel interface to Tempe
ro1-91309(config-if)# bandwidth 1500
ro1-91309(config-if)# ip address x.x.x.x.x
ro1-91309(config-if)# ip mtu 1400
%Warning: IP MTU value set 1400 is greater than the current transport value 1376, fragmentation may occur
ro1-91309(config-if)# ip hello-interval eigrp 65100 10
ro1-91309(config-if)# ip hold-time eigrp 65100 40
ro1-91309(config-if)# ip flow ingress
ro1-91309(config-if)# ip flow egress
ro1-91309(config-if)# ip pim sparse-mode
ro1-91309(config-if)# ip nat outside
ro1-91309(config-if)# ip nhrp authentication cisco
ro1-91309(config-if)# ip nhrp map 10.2.0.1 x.x.x.x
ro1-91309(config-if)# ip nhrp map multicast x.x.x.x
ro1-91309(config-if)# ip nhrp network-id 1001
ro1-91309(config-if)# ip nhrp holdtime 600
ro1-91309(config-if)# ip nhrp nhs 10.2.0.1
ro1-91309(config-if)# ip nhrp registration timeout 30
ro1-91309(config-if)# ip virtual-reassembly in
ro1-91309(config-if)# zone-member security TRUST
ro1-91309(config-if)# ip tcp adjust-mss 1360
ro1-91309(config-if)# ip summary-address eigrp 65100 10.8.80.0 255.255.255.0 5
ro1-91309(config-if)# load-interval 30
ro1-91309(config-if)# if-state nhrp
ro1-91309(config-if)# qos pre-classify
ro1-91309(config-if)# tunnel source FastEthernet0/1
ro1-91309(config-if)# tunnel destination x.x.x.x
ro1-91309(config-if)# tunnel key 1001
ro1-91309(config-if)# tunnel protection ipsec profile iGBN
ro1-91309(config-if)# max-reserved-bandwidth 100
service_policy on dynamic interface is not allowed if there is fair-queue configured on main interface
ro1-91309(config-if)# hold-queue 4096 in
ro1-91309(config-if)# hold-queue 4096 out
ro1-91309(config-if)#end
Crypto settings
crypto isakmp policy 1
encr aes
hash md5
group 5
crypto isakmp invalid-spi-recovery
crypto isakmp keepalive 30 12
crypto ipsec security-association replay window-size 1024
crypto ipsec transform-set iGBN esp-aes esp-md5-hmac
mode transport
crypto ipsec profile iGBN
set transform-set iGBNYou should be good with this configuration -
Here is the explaination-
When an IP packet has been split into two fragments and encapsulated by GRE. In this case IPsec will see two independent GRE + IP packets. Often in a default configuration one of these packets will be
large enough that it will need to be fragmented after it has been encrypted. The IPsec peer will have to reassemble this packet before decryption. This "double fragmentation" (once before GRE and again after IPsec) on the sending router increases latency and lowers throughput. Also, reassembly is process-switched, so there will be a CPU hit on the receiving router whenever this happens. This situation can be avoided by setting the "ip mtu" on the GRE tunnel interface low enough to take into account the overhead from both GRE and IPsec (by default the GRE tunnel interface "ip mtu" is set to the outgoing real interface MTU - GRE overhead bytes). -
Hey people. I'm trying to solve a small VRF Lite project I've been working on. Router has one public interface. I have GRE tunnels going to a VTI. I also created a second tunnel VTI and put it in a VRF so that I could have one plain GRE tunnel and also a second GRE tunnel that supports IPSEC. I can't seem to figure out how to route packets in and out of the VRF and global table. From a tunnel established on the VRF, I would like to ping one of the global table peers networks (or even a loopback interface on the router itself). Below is my config. Any help is appreciated.
ip vrf IPSEC-Customers
rd 65000:1
route-target export 65000:1
route-target import 65000:1
interface Tunnel0
bandwidth 100000
bandwidth inherit
ip address 10.1.1.1 255.255.255.0
no ip redirects
ip mtu 1500
ip nat inside
ip nhrp map multicast dynamic
ip nhrp network-id 1011
ip nhrp holdtime 30
ip nhrp registration timeout 30
ip virtual-reassembly
ip tcp adjust-mss 1400
load-interval 30
qos pre-classify
tunnel source 204.12.X.X
tunnel mode gre multipoint
tunnel bandwidth transmit 100000
tunnel bandwidth receive 100000
interface Tunnel1
bandwidth 10000
bandwidth inherit
ip vrf forwarding IPSEC-Customers
ip address 10.1.2.1 255.255.255.0
no ip redirects
ip mtu 1500
ip nhrp map multicast dynamic
ip nhrp network-id 1012
ip nhrp holdtime 30
ip nhrp registration timeout 30
ip tcp adjust-mss 1400
load-interval 30
qos pre-classify
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 50
tunnel bandwidth transmit 100000
tunnel bandwidth receive 100000
tunnel protection ipsec profile DMVPN1
interface FastEthernet0/0
bandwidth 10000
ip address 204.12.X.X 255.255.2X.X
ip access-group Outside_In in
ip nbar protocol-discovery
ip flow ingress
ip flow egress
ip nat outside
ip virtual-reassembly
load-interval 30
duplex auto
speed auto
router bgp 65000
no synchronization
bgp log-neighbor-changes
no auto-summary
address-family ipv4 vrf IPSEC-Customers
redistribute connected
redistribute static
no synchronization
exit-address-family
ip route vrf IPSEC-Customers 10.2.7.0 255.255.255.0 10.1.2.3 name TestHello,
The tunnel source and destination must be in the same vrf for this to work. In another case you can use a tunnel to ride over a vrf if required.
So your global table would then become a vrf, i am not sure if we can do this with the global table... :-/ Using your example below:
ip vrf IPSEC-Customers
rd 65000:1
route-target export 65000:1
route-target import 65000:1
ip vrf GLOBAL
rd 1:1
interface Tunnel0
ip vrf forwarding GLOBAL
bandwidth 100000
bandwidth inherit
ip address 10.1.1.1 255.255.255.0
no ip redirects
ip mtu 1500
ip nat inside
ip nhrp map multicast dynamic
ip nhrp network-id 1011
ip nhrp holdtime 30
ip nhrp registration timeout 30
ip virtual-reassembly
ip tcp adjust-mss 1400
load-interval 30
qos pre-classify
tunnel source 204.12.X.X
tunnel mode gre multipoint
tunnel bandwidth transmit 100000
tunnel bandwidth receive 100000
interface Tunnel1
bandwidth 10000
bandwidth inherit
ip vrf forwarding IPSEC-Customers
ip address 10.1.2.1 255.255.255.0
no ip redirects
ip mtu 1500
ip nhrp map multicast dynamic
ip nhrp network-id 1012
ip nhrp holdtime 30
ip nhrp registration timeout 30
ip tcp adjust-mss 1400
load-interval 30
qos pre-classify
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 50
tunnel bandwidth transmit 100000
tunnel bandwidth receive 100000
tunnel protection ipsec profile DMVPN1
tunnel vrf GLOBAL
interface FastEthernet0/0
ip vrf forwarding GLOBAL
bandwidth 10000
ip address 204.12.X.X 255.255.2X.X
ip access-group Outside_In in
ip nbar protocol-discovery
ip flow ingress
ip flow egress
ip nat outside
ip virtual-reassembly
load-interval 30
duplex auto
speed auto
I haven't tested this myself but I have come across this in my studies. In theory this should work.
hope this helps
Bilal (CCIE #45032) -
Smallest Cisco 800 series + DMVPN?
Hello
Recently I've been looking into posibilities for extending a DMVPN (already implemented) with very small (1-2 user) remote locations over a single ISP link.
I would like to use what is basically the smallest Cisco router that supports DMVPN and EIGRP (stub) - here's a sample configuration:
interface Tunnel***
bandwidth ***
ip address ***
ip hold-time eigrp ***
ip nhrp authentication ***
ip nhrp map *** ***
ip nhrp map multicast ***
ip nhrp network-id ***
ip nhrp holdtime ***
ip nhrp nhs ***
ip nhrp registration timeout ***
tunnel source ***
tunnel mode gre multipoint
tunnel key ***
tunnel path-mtu-discovery
tunnel protection ipsec profile ***
All this accompanied by the appropriate transform set and isakmp policy.
I know that the 881 can accomplish the above without issues (if it has Adv IP Services as licensing).
I would like to know if I can use the smaller routers (physically smaller, that is) for a similar configuration. Can anyone provide insight here? Can the Cisco 819 router (http://www.cisco.com/en/US/prod/collateral/routers/ps10906/ps380/ps11615/data_sheet_c78-678459.html)
provide the same functionality? What about the Cisco 866VAE router (http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78-693249.html)?819 does support both DMVPN and EIGRP.
866VAE does not support DMVPN. -
Jabber registration issue on CCM 7.1.5
Hi Guys, I'd like to ask your valuable advice on the following:
- we're running CCM 7.1.5(b)SU5
- we installed the following .cop files for Android support (we tried one after the other hoping to get around the problem):
cmterm-android_8.6.2v17.cop.sgn
cmterm-android_8.6.2v17b.cop.sgn
cmterm-android_9.0.1v24.cop.sgn
- we forced the phone (Samsung Galaxy S GTi9000) to install the following Jabber client (found on CCO together with the above device files for which it should be compatible):
Release 8.6(5) - Optimus-MR3-aligned.apk
Unfortunately we had no luck and the phone gets always the 'timeout/check network config' error.
This is what you see on CCM side:
12/07/2012 10:51:44.332 CCM|SIPStationD(7,100,169,47), BOTTEST, 10.40.251.125:40916, primaryDN=5011, Registration profile error: Error: DB Config, sending registration reject and closing station|<CLID::CCMSG-Cluster><NID::10.40.11.23><CT::0,0,0,0.0><IP::><DEV::><LVL::Error><MASK::0020>
... we followed all the Cisco guidelines to create a suitable device configuration (the same worked like a charm on CCM 8.5).
I'll attach a CCM trace showing the above error (as you may have guesses, the phone name is 'BOTTEST')
Thanks a lot !
- AndreaI've been having a real fun time trying to get Jabber for Android working as well. CUCM version 8.6.2 and Jabber 9.0.
The trick was to check the box for 'Use Fully Qualified Domain Name in SIP Requests' in the SIP profile you created for Android phones.
I was connecting to the CUCM, but then it would time out.
Thanks,
Richard -
Hi Everyone,
We have the password portal up and running on one box and another server with FIM R2 and SharePoint 2010. All is good with the exception that our end users typically get distracted during the password registration and/or reset process and receive:
"An error has occurred. Please try again, and if the problem persists, contact your help desk or system administrator. (Error 3000) ". The timeout kicks in after 5 minutes of inactivity in the browser.
The FIM Service log shows the following:
"Authentication gate timed out waiting for a challenge response".
I have confirmed that the default password portal web.config setting is <add key="SessionTimeoutInMinutes" value="20" />.
We have also updated Microsoft.ResourceManagement.Service.exe.config per this
article to the following but with no luck:
<resourceManagementClient resourceManagementServiceBaseAddress="myAddress" timeoutInMilliseconds="600000" />
<resourceManagementService externalHostName="myHost" dataReadTimeoutInSeconds="600" dataWriteTimeoutInSeconds="600"/>
We did not update the Windows SharePoint Servicesweb.config setting per the article about since we are on SharePoint 2010.
There is no NLB or firewall in front on this server.
If anyone has any solution to how to solve this on FIM R2/SharePoint 2010 please let me know.
Cheers!FIM_Admin,
You could try changing the receiveTimeoutInSeconds parameter of the resourceManagementService node in your Microsoft.ResourceManagement.Service.exe.config file. However, you are warned not to do this unless instructed to by MS customer support.
http://msdn.microsoft.com/en-us/library/windows/desktop/ee652424(v=vs.100).aspx
http://technet.microsoft.com/en-us/library/ff800821(v=ws.10).aspx -
SapSetup failed in the registration of
Hello,
we're facing a blocking issue in our SAP GUI 7.10 Patch 3 deployment via SMS.
On some computers (not all) the sapsetup crashes with the following single log :
Any tip on how to fix that ?
Logfile: C:\Program Files\SAP\SapSetup\LOGs\NWSAPS~1.log
Started logging: Fri Jan 04 09:18:37 2008
Operating system: Windows XP (Version 5.1 Build# 2600)
Browser version: Internet Explorer 6.00
Executing user: SYSTEM (Administrator)
Workstation name: PLWARN0PL0183
Windows directory: C:\WINNT
Temp directory: C:\WINNT\TEMP
ThreadId: 2988, ProzessId: 796
Commandline: "
PLWARSSMS03\PACKAGES\SAP_71\Setup\NWSAPS~1.EXE" /noDlg /Package="SAP 7.10"
Executable:
PLWARSSMS03\PACKAGES\SAP_71\Setup\NWSAPS~1 (PID 796)
Physical memory: 581 MB of 1272 MB free
System libraries information
atl.dll: 3.5.2284.0
comctl32.dll: 5.82.2900.2982
mfc42.dll: 6.2.4131.0
msvcrt.dll: 7.0.2600.2180
oleaut32.dll: 5.1.2600.3139
shell32.dll: 6.0.2900.3241
shlwapi.dll: 6.0.2900.3231
SAP Setup libraries information
NwSapSetupEngine.dll: 8.0.0.376
NwSapFeiUt.dll: 8.0.0.376
NwSapFeiKr.dll: 8.0.0.376
NwSapFeiLg.dll: 8.0.0.376
NwSapFeiSh.dll: 8.0.0.376
09:18:43 NwSapFeiKr 2 SAP Frontend Installation Kernel initialized
(Unicode Release build)
09:18:52 NwSapsEngn 1 SapSetup Workstation Engine Library Loaded
09:18:59 NwSapSetUI 1 SapSetup UI Library Loaded
09:19:08 NwSapsAtlC 1 SapSetup ATL Common Library Loaded
09:19:10 NwSapSetup 1E SAPSetup Server (Un-)Registration: General Failure
09:19:10 NwSapSetup 1E SapSetup failed in the registration of
PLWARSSMS03\PACKAGES\SAP_71\Setup\NwSapFeiKr.Dll
09:19:10 NwSapSetup 1E SapSetup failed in the registration of
PLWARSSMS03\PACKAGES\SAP_71\Setup\NwSapFeiSh.Dll
09:19:10 NwSapSetup 1E SapSetup failed in the registration of
PLWARSSMS03\PACKAGES\SAP_71\Setup\NwSapSetupAtlCommon.Dll
09:19:10 NwSapSetup 1E SapSetup failed in the registration of
PLWARSSMS03\PACKAGES\SAP_71\Setup\NwSapSetupUi.Dll
09:19:10 NwSapSetup 1E SapSetup failed in the registration of
PLWARSSMS03\PACKAGES\SAP_71\Setup\NwSapSetupEngine.Dll
09:19:10 NwSapSetup 1 Registration Activity took 30.054582 seconds
09:19:10 NwSapFeiSh 1 Trying to load '
PLWARSSMS03\PACKAGES\SAP_71\Setup\vbscript.dll'...
09:19:12 NwSapFeiSh 1 "
PLWARSSMS03\PACKAGES\SAP_71\Setup\vbscript.dll" successfully loaded.
09:19:16 NwSapsEngn 1E Data Exchange not Constructed
09:19:16 NwSapsEngn 1E UI Manager not Constructed
09:19:16 NwSapsEngn 1E Error in creating DE Variable Collection
09:19:18 NwSapsEngn 1 Engine: Commencing execution
09:19:18 NwSapsEngn 1 Initializing the Installation Engine
09:19:18 NwSapsEngn 1 EngineContext released
09:19:18 NwSapsEngn 1E Engine Context not Constructed
09:19:18 NwSapsEngn 1E Installer Engine: Command Line Arguments Object not constructed
09:19:18 NwSapsEngn 1E SapSetup Error manager not created - Error control dysfunction
09:19:18 NwSapsEngn 1E Engine Initialize unknown failure: quitting
09:19:19 NwSapFeiSh 1E Microsoft VBScript runtime error (0x800a01a8)
Object required: 'NwEngine.Context' (Line 11, Col. 1)
The setup script contains the error listed above. Please contact your system administrator and provide this information, for example by sending him a screenshot of this message box (Press Alt+PrtScrn to create the screenshot and copy it to the clipboard).
09:19:19 NwSapSetup 1 Un-Registration Activity took 0.000004 seconds
09:19:19 NwSapSetup 1 Un-registration complete
09:19:19 NwSapSetUI 1 SapSetup UI Library Unloaded
09:19:19 NwSapsAtlC 1 SapSetup ATL Common Library Unloaded
09:19:19 NwSapFeiKr 2 SAP Frontend Installation Kernel shutdown
09:19:19 NwSapsEngn 1 SapSetup Workstation Engine Library Unloaded
09:19:19 NwSapsEngn 1 DM Deleted
09:19:19 NwSapsEngn 1E Engine Flush Data unknown failure: quitting
09:19:19 NwSapsEngn 1 This Engine Instance lasted 0.051194 minutes
09:19:19 NwSapsEngn 1 Engine DeletedI have the same problem. Have you got any solve?
Logfile: C:\Program Files\SAP\SapSetup\LOGs\NwSapSetup.log
Started logging: Thu Sep 25 19:45:15 2008
Operating system: Windows XP (Version 5.1 Build# 2600)
Browser version: Internet Explorer 6.00
Executing user: SYSTEM (Administrator)
Workstation name: DACZC8225XF3
Windows directory: C:\WINDOWS
Temp directory: C:\WINDOWS\TEMP
ThreadId: 320, ProzessId: 5024
Commandline: p:\Setup\NwSapSetup.exe /Silent /Package="SAP_GUI_710_9"
Executable: p:\Setup\NwSapSetup (PID 5024)
Physical memory: 1024 MB of 2003 MB free
System libraries information
atl.dll: 3.5.2284.0
comctl32.dll: 5.82.2900.2982
mfc42.dll: 6.2.4131.0
msvcrt.dll: 7.0.2600.2180
oleaut32.dll: 5.1.2600.3266
shell32.dll: 6.0.2900.3241
shlwapi.dll: 6.0.2900.3354
SAP Setup libraries information
NwSapSetupEngine.dll: 8.1.0.107
NwSapFeiUt.dll: 8.1.0.107
NwSapFeiKr.dll: 8.1.0.107
NwSapFeiLg.dll: 8.1.0.107
NwSapFeiSh.dll: 8.1.0.107
19:45:34 NwSapFeiUt 3 Utilities Library initialized (Unicode Release build)
19:45:38 NwSapFeiUt 3 IPC(Source) : waiting 0 ms for listener to become alive...
19:45:38 NwSapFeiUt 3 IPC(Source) : timeout
19:46:07 NwSapFeiKr 2 SAP Frontend Installation Kernel initialized
(Unicode Release build)
19:46:16 NwSapFeiSh 3 Scripting Host initialized (Unicode Release build)
19:46:24 NwSapSetup 1E SAPSetup Server Registration / Unregistration: General Failure (can be caused by a slow network)!
19:46:24 NwSapSetup 1E SapSetup failed in the registration of p:\Setup\NwSapFeiKr.Dll
19:46:24 NwSapSetup 1E SapSetup failed in the registration of p:\Setup\NwSapFeiSh.Dll
19:46:24 NwSapSetup 1E SapSetup failed in the registration of p:\Setup\NwSapSetupAtlCommon.Dll
19:46:24 NwSapSetup 1E SapSetup failed in the registration of p:\Setup\NwSapSetupUi.Dll
19:46:24 NwSapSetup 1E SapSetup failed in the registration of p:\Setup\NwSapSetupEngine.Dll
19:46:24 NwSapSetup 1 Registration Activity took 45.000655 seconds
19:47:03 NwSapsAtlC 1 SapSetup ATL Common Library Loaded
19:47:03 NwSapSetup 1E Server could not be loaded
19:47:03 NwSapSetup 1E Server could not be loaded
19:47:03 NwSapSetup 1E Reason - : The specified module could not be found.## Error code 0x7e (126)
19:47:03 NwSapSetup 1E Reason - : The handle is invalid.## Error code 0x6 (6)
19:47:05 NwSapFeiSh 1 Trying to load 'p:\Setup\vbscript.dll'...
19:47:16 NwSapFeiSh 1 "p:\Setup\vbscript.dll" successfully loaded.
19:47:18 NwSapFeiUt 3 Security : no previous CRC32 checksum available for 'p:\Setup\nwsapsetup.xsc'
19:47:20 NwSapFeiSh 1E Microsoft VBScript runtime error (0x800a01ad)
ActiveX component can't create object: 'NWSapSetupEngine.Engine' (Line 4, Col. 1)
The setup script contains the error listed above. Please contact your system administrator and provide this information, for example by sending him a screenshot of this message box (Press Alt+PrtScrn to create the screenshot and copy it to the clipboard).
19:47:20 NwSapFeiUt 3 IPC(Source) : waiting 0 ms for listener to become alive...
19:47:20 NwSapFeiUt 3 IPC(Source) : timeout
19:47:20 NwSapSetup 1 Un-Registration Activity took 0.000002 seconds
19:47:20 NwSapSetup 1 Un-registration complete
19:47:20 NwSapFeiSh 3 Scripting Host shutdown
19:47:20 NwSapsAtlC 1 SapSetup ATL Common Library Unloaded
19:47:20 NwSapFeiKr 2 SAP Frontend Installation Kernel shutdown
19:47:20 NwSapFeiUt 3 Utilities Library shutdown -
Timeout during allocate / CPIC-CALL: ThSAPCMRCV
We have the error: "timeout during allocate / CPIC-CALL: ThSAPCMRCV" when test our RFC "MDX PARSER". Windows 2003 x64 Server, SAP NetWeaver 7.0 Unicode. We read notes about this error (for example 1032461) but we have another problem. Our problem concerned librfc32.dll registration (we doing this using command: regsvr32 C:\Windows\system32\librfc32.dll) because of this we can't starts mdxsvr. Anybody doing same operation on Windows 2003 x64 server?
Hi
I think you should post this in basis and security forum.
Cheers
Chanda
Maybe you are looking for
-
How can I delete specific convos in the messages app without it gliching?
I have an iPhone 4S with absolutely everything up to date. Now I'm pretty much what you could call a texting hoarder.. I have text messages on my phone all the way up until the previous year sometimes. As of this very moment, I'm trying to delete cer
-
Vista doesn't recognize d drive, I tunes reformats
My Vista loaded laptop was not recognizing the d drive, Microsoft had me enter the register and delete the upper and lower filters, which fixed that problem, however it caused Itunes to be unable to burn a disc, Itunes suggested re downloading Itunes
-
Any way to link to a file in Catalyst, rather than a URL or state?
Given the 20 page limitation, I'm having to build my prototype in chunks, but so far have been unable to find a way to link up the various prototypes. Does anyone know of a way to add a link to a local file rather than a live URL or simply another s
-
IPhone 6 Plus-iOS 8.3 Deleted all music on my phone but songs still showing
I have a problem where I cannot delete some/most of the songs on my iPhone. I've already tried syncing the phone with my iTunes library (which is empty on my computer) and these songs are still on my phone. There's about 185 of them. I've tried this
-
Keep getting an error about no gdk module being available when trying to load a python script. I have up-to-date versions of both python and pygtk. any ideas?