Replacing HD in dv6110ca with a drive from another HP laptop

Hello there...
I have a DV2500 that has died. The hard drive is a Fujutsu 250gb. I also have a dv6110ca that the HD maybe on its last legs. Would the 250gb drive from the dv2500 fit the dv6110ca??

Hi,
Yes, physically fit. All standard 2.5" HDD's have same size. The new generation HDD's are thinner but still fit. Your machines use the previous generation.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

Can I take a hard drive from a different laptop and replace it in my MacBook pro 2007

My MacBook pro (2007) has failing hard drive. Can I remove the hard drive from a different laptop ie. Toshiba, or HP and replace it with the failing hard drive?

yes you can....but any files/data on the other drive will be gone. also make sure that the drive you install is a SATA drive which is in your Macbook...
make sure you have your original install disk if you plan on doing a clean install.

No "Fiery Features" with latest driver from Canon only "Printer features".

No "Fiery Features" with latest driver from Canon only "Printer features". iRC5235's using 'OSX installer PKG'. Installation completes successfully. Can successfully add the printer(s). Just cannot access the "Fiery Features" just "Printer Features". Other users are working fine. The driver is "Canon iR-ADV C5200s-B2 PSV10US". Already have removed, restarted and reinstalled numerous times - no progress. It should be noted that this user may print to the devices, just cannot access any of the "Fiery features" which are desired. Any thoughts? Thank you in advance for your assistance.

If the user is only getting Printer Features, then it would suggest that the wrong PPD is being selected when the printer is being added. For example, the PPD's for the internal Canon board will show Printer Features in print dialog. So while you mention the B2 driver is being used, are you sure it was selected when the print queue was created?
To check, you can open System Information (Applications > Utilities) and select Printers in the left column. Then in the top right pane, select the iR ADV C5235 with the B2 attached. The bottom right pane will give information about the print queue. The entry PPD will show which PPD is being used and it should show as you have shown above, ie "Canon iR-ADV C5200s-B2 PSV10US".
If the correct PPD was selected then another possible cause is a problem with the Fiery Features plugin. Via Finder, navigate to
/Library/Printers/Canon/PS3/PDEs/EF005626
and check that you have the file "EF005626(FF).plugin". This is the Fiery Feature plugin. If it is present, then maybe this user is having access issues to this folder/plugin.

Can you install osx lion with thumb drive from 10.6.3

can you install osx lion with thumb drive from 10.6.3

No. You can install Snow Leopard with a flash drive 10.6.3 installer. However, for Lion you must start with 10.6.8 in order to access the App Store to purchase and download Lion.

How do I format a internal Hard Drive from a PC/laptop

How do I format a internal Hard Drive from a PC/laptop...My old internal hard drive had problems so I took it out and I have a 100 gb Seagate ATA drive that I replaced it with. In the mean time I've been using a external drive to boot up my powerbook g4. Not sure of what to do.

Hi, capitala1. Start your Powerbook up from your Mac OS X installer disc and open Disk Utility from the Installer or Utilities menu (depending on which OS version it is). Select the newly-installed Seagate drive inside your Powerbook as the target, and format it "Mac OS Extended (Journaled)". It makes no difference at all that the drive came out of a PC laptop: this is exactly the same procedure you'd use if the drive had just come brand new from its manufacturer.

I'm trying to clone a internal hard drive from another mac using a usb connection.

I'm trying to clone a internal hard drive from another mac using a usb connection to an external drive so that I don't lose the file before reinstalling the software but I keep on getting a message:
"Restore Failure
Source volume is read-write and cannot be unmounted, so it can't be block copied."
Any advice on how to make a copy of this internal drive?
Thanks!
....also the internal hard drive i am trying to copying run on a mac os x 10.5 and i'm reinstalling the software because the computer is not starting and only shows a grey folder with a question marks inside.

I've had my Maxtor external OneTouch 250GB for about 18 months now and it hasn't skipped a beat. I have hear of people having their Maxtor drive just up and die but you will probably find that goes for all manufacturers.
By the way, Maxtor is, amongst others, an OEM supplier to Apple.

I am having some issues getting OS X to mount the hard drive from my old laptop (Windows 7). Is there anything I can do to mount this?

I am having some issues getting OS X to mount the hard drive from my old laptop (Windows 7). Is there anything I can do to mount this?
It is not showing on the Desktop or the left colomn of Finder (Set to do both in Finder Prefernces) and is not showing up under the Disk application under Utilities (Sorry can't remember the name off the top of my head!)

cjz0r wrote:
...I'm starting to think it is most likely NTFS, am I looking at needing an Application to read the NTFS partitions on the drive?
You should be able to read NTFS formatted drives, just not write to them. For that matter, USB Flash drives generally come formatted NTFS for use with PC's and they have to be able to mount on a Mac in order to reformat them for Mac use. The Windows utilities supplied on those Flash drives will be deleted when the drive is reformatted for Mac use so I routinely copy them to the Mac desktop first before reformatting.
You might look into something like this http://eshop.macsales.com/item/NewerTech/U3NVSPATA/ if the enclosure is an issue. It looks weird but it works.

If I have my old hard drive from my windows laptop, can I use that as a partition?

i was wondering since i recently upgraded to a mac, if i could use my old hard drive from my windows laptop, with a usb connection, if i could use that as a windows partition for gaming and other things of that nature that are only support windows.

If you mean that you want to run Windows from a USB
drive, you can't. Windows itself can only boot from
internal drives. This is a limitation of Windows.

Using CD drive from another laptop

How do I use a CD drive from another laptop to download music CD's onto my MacBook Air?

Here's how:
DVD or CD sharing: Using Remote Disc

UPDATING A TABLE WITH SAME INFO FROM ANOTHER TABLE ON THE SAME DB

0down votefavorite
I am trying to update a table with info from another table on the same db with same table name. I just want the info to be the same , no primary key or constraint involve just a straight replacement of records and I keep getting errors WITH THE TABLE not
being recignize. below is my query:
UPDATE
VNDFIL
SET EOBTYP
= VNDFIL.EOBTYP,
EDI_X12_835_VERSION = VNDFIL.EDI_X12_835_VERSION
FROM
AGERECOVERY
WHERE
VNDFIL.EOBTYP
= VNDFIL.EOBTYP
AND
VNDFIL
.EDI_X12_835_VERSION
= VNDFIL.EDI_X12_835_VERSION

Hi rotary,
If those two same named tables are in the same database then they have to be in different schemas. If you mean they are in the same server instance, then they may be in different databases, besides the "table not being recognized" error,
anyway you should use the fully qualified table names, that is database.Schema.Table(If across instances, ServerName should be prefixed) to avoid the table unrecognized error.
Using Identifiers As Object Names
With the fully qualified names, your update statement can be like below.
UPDATE
db1.schema1.VNDFIL
SET EOBTYP = srcTbl.EOBTYP, EDI_X12_835_VERSION = srcTbl.EDI_X12_835_VERSION
FROM
db1.schema2.VNDFIL srcTbl
WHERE
db1.schema1.VNDFIL.EOBTYP = srcTbl.VNDFIL.EOBTYP AND
db1.schema1.VNDFIL.EDI_X12_835_VERSION = srcTbl.VNDFIL.EDI_X12_835_VERSION
If you have any question, feel free to let me know.
Eric Zhang
TechNet Community Support

Copy standard cost with Cost Component from another material

Hi,
I need to copy standard cost from another material not only total price but also details of cost component split. I try to used transaction CKUC with procedure of "explode material cost estimate" but the reference material use "mixed costing" and isystem stop explosion.
There is another procedure in order to make this copy? I can not use special procurement because are different codes (material A / Plant XXX copy froma material B /Plant XXX).
Thanks for your support.
Mic

Hi Chandra,
thanks for your suggestion, it works but only if I explode a level ... material "B" contains two mix codes that also contain their mixes. So system shows this message "Mixed cost estimate explosion in level 2 for material xxx" and "Mixed cost estimate exists: maximum of 2 explosion level (s) possible".
So Is not possible to copy and esploded a standard cost with multi level mix?
Thanks
Michela

Initialize a global with a global from another file

hi,
I know that initialization order for global variables across compilation units is not defined, but if I have
file1.cpp
int x0 = 33, x1 = 55;
extern int y0, y1;
static int a[] = { y0, y1 };
void print_a( void ) { printf( "\na[0] = %d\na[1] = %d", a[0], a[1] ); }
extern void print_b( void );
main()
print_a();
print_b();
and file2.cpp
int y0 = 77, y1 = 99;
extern int x0, x1;
static int b[] = { x0, x1 };
void print_b( void ) { printf( "\nb[0] = %d\nb[1] = %d", b[0], b[1] ); }
I notice that values are displayed correctly and consequently, initialized in the order I need. So what's the secret, coincidence, am I lucky? Does it make any difference if file2.cpp is part of a static library?
Thanks

@ Igor Tandetnik: Yes, I chose an example with circular dependency just to show that it was not the situation that, by luck, the "other" file was was initialized first. Yes, I would like a solution for such circular dependency, but I hope that I will
find, at least, a solution for the case when such circular dependency does not exist. What I want to achieve? As the title says, I want a solution to be able to initialize globals with globals from another file, a solution as general and fault proof and convenient
as possible.
@ Wyck: I thought about something like that, problem is that in case of large arrays there is a lot to type. Another solution (it saves a little typing) I saw was something like
// common_header.h
#define LIST_A y0, y1
#define LIST_B x0, x1
// file1.cpp
#include "common_header.h"
Number x0(33), x1(55);
static Number a[] = { LIST_A }; // just to give correct size
// file2.cpp
#include "common_header.h"
Number y0(77), y1(99);
static Number b[] = { LIST_B }; // just to give correct size
// init.cpp
extern Number LIST_A, LIST_B;
void init()
{ Number a_[] = { LIST_A }; Number b_[] = { LIST_B }; // stack usage
for( int i = 0; i <_countof( a_ ); i++ ) a[ i ] = a_[ i ];
for( int i = 0; i <_countof( b_ ); i++ ) b[ i ] = b_[ i ];
This still has the problem of using much stack in case of large arrays and if array members are more complex structures (might also contain string literals), there is a bit more difficult.
Bellow is a solution I came up with using macros but which I don't really like because is a bit cumbersome. I'm looking for something better/more elegant/safer or simply I want to see what other solutions people see here.
// file1.cpp -------------------------------------------
#define MEMBER_LIST( Usage ) \
Usage( x1 ) \
Usage( x2 )
#define IMPORT( ext_member ) extern Number ext_member;
#define COUNT( member ) 1 +
#define LOAD( member_val ) a[ i++ ] = member_val;
Number y1 = 77, y2 = 99;
MEMBER_LIST( IMPORT )
static Number a[ MEMBER_LIST( COUNT ) 0 ];
static void InitGlobals_a( void ) { uint8 i = 0; MEMBER_LIST( LOAD ) }
extern void InitGlobals_b( void );
int _tmain(int argc, _TCHAR* argv[])
{ InitGlobals_a(); InitGlobals_b();
return 0;
// file2.cpp -------------------------------------------
#define MEMBER_LIST( Usage ) \
Usage( y1 ) \
Usage( y2 )
#define IMPORT( ext_member ) extern Number ext_member;
#define COUNT( member ) 1 +
#define LOAD( member_val ) b[ i++ ] = member_val;
Number x1 = 33, x2 = 55;
MEMBER_LIST( IMPORT )
static Number b[ MEMBER_LIST( COUNT ) 0 ];
void InitGlobals_b( void ) { uint8 i = 0; MEMBER_LIST( LOAD ) }
Of course, something like
#define MEMBER_LIST( Usage ) Usage( x1 ) Usage( x2 )
could be further simplified using other macros so you can simple use
#define MEMBER_LIST x1, x2
but those additional macros will add up to the complexity.

Read group membership for a user object and populate every group with matching user from another domain

I have LON\JSmith in LON domain and DEL\JimSmith in DEL domain
I would like to extract group memberships of LON\JSmith in LON domain and append matching by email (i.e. DEL\JimSmith) user object in every group in LON domain.
for instance
LON\JSmith and DEL\JimSmith is the same person and has same email address [email protected]
LON\JSmith belongs to 3 groups - LON\localadmingroup;LON\univdesktop;LON\globalsurvey
The outcome of the script should be
LON\JSmith; DEL\JimSmith should be in 3 groups - LON\localadmingroup;LON\univdesktop;LON\globalsurvey.
How can i do it?
Navgup

Hi Navgup,
Please refer to the script below, to query users in other domain by specifying the parameter "-Server" in the cmdlet "get-aduser", and also note I haven't tested the script below:
import-module activedirectory
get-adgroupmember "group"|foreach{
$email=(get-aduser $_.samaccountname -properties *).EmailAddress#get the user email
Get-ADUser -filter {EmailAddress -eq $email} -properties * -server DomainB.company.com|select samaccountname, memberof}#filter user name and group with the email in other domain
To get users across domain, please also refer this blog:
Adding/removing members from another forest or domain to groups in Active Directory:
http://blogs.msdn.com/b/adpowershell/archive/2010/01/20/adding-removing-members-from-another-forest-or-domain-to-groups-in-active-directory.aspx?Redirected=true
I hope this helps.

Problem with creating site from another computer!

Hi
I have WebDB 2.2 and Oracle8i instaled on the same computer. I have a problem to create site from another computer. There is not any process when I try to create site. There is always 0%.
But I have no problem with creating site on the origin computer.
Does anybody know something about it?

I am just not clear what to do once I have made changes and have published the new information.
You shouldn't have to do anything. iWeb will save the information in the Domain.sites file. You can keep this file in a folder, or even on your desktop and iWeb will launch from a double-click on the file.

Breakout table (fill table with matching data from another table)

Hi
I've been trying to study old discussions about breakout tables. I feel I'm close, but still no cigar :-)
In plain english, I'm trying to autocreate rows with data on a table, based on matching values from another table. E.g. have a table to display all rows where type = AssetX
I have attached a screenshot of my "master table" called Assets:
I'm looking to prefill Asset name, Total from this table and populate a new table called e.g. Greenhouse
Where I'd be adding more data (date, income, expense).
Any help whould be greatly appreciated.
Thanks!

Hi,
Here is a Sample Query.
Update Emp A
Set Sal = (Select Sal from emp b where
a.empno = b.empno)
where empno in (select empno from emp);
Regards,
Ganesh R
null

Replacing HD in dv6110ca with a drive from another HP laptop

Similar Messages

Maybe you are looking for