Reset PMU... mouse still stuck..now what?

Hi,
I fixed logic board problem and graphics
Tried to fix mouse by resetting PMU
Now the computer (when you start it) grey screen with apple comes up and locks when the whell at the bottom comes up. Any suggestions?

I'm wondering if you inadvertently disconnected the trackpad somehow? Is it still not working? If it isn't, here is a link to Michael Baker's detailed instructions on how to reconnect it (in case that is the problem):
http://discussions.apple.com/thread.jspa?messageID=1034519#1034519
Does it work okay with a USB mouse?
Will it start up from the Panther Install CD by putting the Install CD into the tray and holding down the c key at the end of the startup chime? If so, then choose Installer > Open Disk Utility and select the hard drive in the left column. Choose the First Aid tab. Click Repair Disk to test and repair the hard drive.
Once you have repaired the hard drive with the Install disc's Disk Utility, then try to start up normally and repair permissions from Disk Utility in the Utilities folder on the hard drive.

Similar Messages

I have a classic that seems to be stuck in restore mode, the screen says "do not disconnect'' and i can't restore using itunes. i have tried resetting it and still no good, what can i do to fix this problem ?

i have a classic that seems to be stuck in restore mode, the screen says "do not disconnect'' and i can't restore using itunes. i have tried resetting it and still no good, what can i do to fix this problem ?

Be good to know what the diagnostic results are.
I've also just run into an issue where I couldn't restore an iPod with a corrupt file system, and the "super fix" in that linked article wasn't working for me. I've run across a potentially useful workaround.
iPod Classic went on the fritz today just after syncing. Couldn't restore via iTunes, kept getting 1439 errors, Windows wouldn't format as FAT32, claimed the "Volume is too big for FAT32". Finally tracked down EaseUS Partition Master Home Edition (Free) and formatted as FAT32 with 128k clusters. The iPod is filling back up again. Might be worth a shot here...
tt2

I was charging my iPhone 5 for about 2 hours. Then I took it off the charger and it wouldn't turn on. I tried to reset it, and still nothing. What do i do to turn it on?

I was charging my iPhone 5 for about 2 hours. Then I took it off the charger and it wouldn't turn on. I tried to reset it, and still nothing. What do i do to turn it on?

Hi Bsut,
Welcome to the Support Communities!
The article below may be able to help you with this.
iOS: Not responding or does not turn on
http://support.apple.com/kb/ts3281
Symptoms
Your iPhone, iPad, or iPod touch may occasionally stop responding to buttons, switches, or touchscreen input and may exhibit one or more of these symptoms:
Does not return to the Home screen after you press the Home button
Does not wake from sleep after you press the Sleep/Wake button
Does not turn on (or power on) when you press any button
Does not start up past Apple logo
Appears frozen or unresponsive
Is unable to "Slide to Unlock" or "Slide to Power Off"
I hope this information helps ....
- Judy

I started downloading ITunes Match last night. The first 2 steps downloaded okay. The 3rd step is stuck at the beginning 64 out of 2479. It is still stuck. What should I do?

I started downloading ITunes Match last night. The first 2 steps downloaded okay. The 3rd step is stuck at the beginning 64 out of 2479. It is still stuck. What should I do?

Are you using the charger and cable that came with the phone?
Are you using an unauthorized third party charger?

I reset my phone... now what do I do????

I just reset my iPhone of everything.. deleting everything... now on the screen its showing up to plug it into itunes.. but when i plug it in nothing happens.. what should i do?

http://support.apple.com/kb/HT1808

Replaced power supply, G5 still dead - now what?

I recently posted that my wife's G5 2.0 (June 2004) had made a loud pop followed by a burning odor, and the consensus on the forum seemed to be that the power source had died. I just replaced the power source, but when I tried to fire up the computer got no results; no light, no chime, nothing. The one thing that the computer IS doing now that it did not after the "popping" incident is that when I turn on the power strip that the computer plugs into, the computer makes a small clicking sound, like a switch being flipped, that it also made before (but not after) the popping incident.
Before taking everything apart and looking to see where I might have screwed up I'd appreciate any advice as to where I should look first. I thought the disassembly and reassembly went pretty smoothly, so I'm a bit bummed at the lack of a positive result (except for the clicking noise being back).
Probably not relevant, but I was interested to see that the power source I pulled from the computer was made by Lite On, so perhaps it had been replaced before I bought it 4 years ago.

So here's where I am now. I disassembled the computer to the point of pulling the heat sinks so I could see the connections to the power supply, except for the plug that sits under the supply and would require pulling the PS out to check. All connections look good. I also looked at the connections from the "start button" back to the boards, and they looked/felt solid.
I did find the SMU reset button that BDAqua mentioned, and that I hadn't found before. I put the good battery out of my own computer in, pushed the SMU reset button, then plugged in and tried to start. No success; no light or any sound when pushing the startup button.
Any ideas what to try next? Could something else have fried when the power supply went? Or could the original popping noise and burning smell been caused by something else entirely? Do I need to pull the power source to make sure the final connection is good? I sure THOUGHT I plugged it together well.
On the positive side, I've gotten really fast at taking the computer apart....

Tryed all 5 Rs-nano still frozen-now what-need help

I have a 4gb nano that is frozen. have tried resetting (hold-menu-select)numerous times. have reinstalled software and rebooted. have completely restored ipod...but screen is still frozen. before restore screen was frozen on main menu--after restore screen is still frozen but on the language screen. I've checked all the support pages and looked through many posts on the discussion site but can't find an answer. Can anyone help or do I need to return this one. This is the second one I've purchased in two weeks--the first froze on the "OK to disconnect" screen. I'm about ready to give up and go back to life with out an ipod! Any ideas?????

mabey call an apple support tech?> Apple Numbers
Nano 4GB black,Moto RAZR V3 black, PSP, all kinds of cases for nano,radio/remote Windows XP <img src="http://i36.photobucket.com/albums/e13/superman5656/s.gif"align="right"</span>

Just got my iphone 5 last week and the power button is stuck now what

is my phone under warranty and can anything be done?

If there's no evidence of user damage (like you dropped it and that's why the power button is stuck), then your phone will be replaced without charge.

HELP!!! My iphone is stuck on the apple logo, I already did the process of putting it into DFU mode and reseted it on itunes and its still stuck!! What do I do now?

I need help!!! I dropped my iphone from the couch to the floor, really not a big fall... it automatically turned off and got stuck with the apple logo, I already did the reseting process on itunes using the DFU mode or however its called... and it erased all my data and now its still stuck!!!
Does anybody know what can I do?? Please help!

If the iPhone is recognized by iTunes, restore it. At the end of the restore process, when you're prompted to by iTunes, do not restore from backup. This will eliminate corrupted/damaged files as the issue.
If the issue persists, it looks like you may need to make a second trip to the Apple store.
Good luck

My iPod is stuck on the USB connector towards the iTunes snd on cd, and I updated it and now it's saying my iPod has apasscode when it's still stuck on that USB screen... What do I do????

My iPod is stuck on the USB connector towards the iTunes snd on cd, and I updated it and now it's saying my iPod has apasscode when it's still stuck on that USB screen... What do I do????

you can do is go to ijailbreak.com then select downloads section.......scroll down and see the latest version of ipod touch second generation is available for download.....when it gets downloaded connect your iPod to itunes or keep it connected then hold option and click restore (mac) search the software by writing in search "iPod" a thing with white cube will show up if it is the file you just downloaded click it and wait for itunes to do its work......you can ask more if you are on windows

HT5787 i forgot Icloud password and security question what method i can use to reset it is ther any or what i am still using iphone but my icloud is disabled for to many atempts what now how to rest the password

i forgot Icloud password and security question what method i can use to reset it is ther any or what i am still using iphone but my icloud is disabled for to many atempts what now how to rest the password

Hi bekimlorini,
Thanks for visiting Apple Support Communities.
You may find this article helpful with resetting your security questions:
Rescue email address and how to reset Apple ID security questions
http://support.apple.com/kb/HT5312
If you're not able to receive email to your rescue email address, you may need to contact iTunes Store Support:
You'll need to contact iTunes Store support to have your questions and answers reset.
All the best,
Jeremy

I cant reset my iphone because it demand restriction code, em stuck now, kindly help what to do to get the **** out ov this?

I cant reset my iphone because it demand restriction code, em stuck now, kindly help what to do to get the **** out ov this?

Force the phone into recovery mode, as described here, & restore it:
http://support.apple.com/kb/ht1808

I am using iPhone 4s with no sim card. My WiFi turned grey and isn't working. I've tried many methods like freezing and Resetting the network settings, still not working. Now what should I do? (iOS 7.1.2)

I am using iPhone 4s with no sim card. My WiFi turned grey and isn't working. I've tried many methods like freezing and Resetting the network settings, still not working. Now what should I do? (iOS 7.1.2)

Put in a micro SIM (SIM need not be active) and
Restore from backup
Restore as new
http://support.apple.com/en-us/HT201252

Blue screen, reset pmu, booted up, now no cursor

hello all...i have received a ibook g4 with some issues. i rebooted it, terminal blue screen, decided to reset pmu, came up after power up, and now no cursor. i tried to plug in a mouse. still nothing! any ideas? just trying to get the ibook back up to get the hard drive emptied off. thanks in advance.

Hi.
Two things to try for starters:
First , try a Starting up in Safe Mode
Safe Boot takes longer than normal startup
What is Safe Boot, Safe Mode.
Then re-boot normally.
If the above doesn't fix things so that you can "...get the ibook back up to get the hard drive emptied off" try booting into Target Disk Mode by holding the 'T' key down at start-up and connect it to your Pro with a firewire cable. The iBook's HD should show on the Pro. Run DU from the Pro to erase the iBook's HD. Use the zero out option (once will be enough) to map out any bad blocks. If you are re-installing you can run the install from the Pro too while the iBook is still in TDM.
Have fun,
Adrian

HP "Support" does not know how to perform "regionalization reset", now what?

I buy a dual voltage OfficeJet 4620 in Germany in Ferbruary 2013.
NOWHERE in the product literature does it mention the ink cartridges are regionalized (defeats the purpose of even manufacturing a 110-220v device! But I digress).
I move to Florida in June and yesterday my black ink begins to run out.
The printer needs the "regionalization reset" which can only be performed by HP support, as stated by their own webpage:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c02558798
Another description of it here:
http://www.fixya.com/support/t156381-change_region_code_ink_cartridges
I call HP support, and waste over an hour and a half with a girl in the Phillipines until she finally tells me that I need a complete set of USA ink cartridges in order to perfom the procedure (which appears to be not true, you do not need them to reset the printer, but rather it appears you need them simply if you wish to print anything after the reset was performed if for no other reason but to verify that the reset was successful). She claims HP support will call me this morning at 11AM EST. They did not call.
I call HP "Support" at 1130 EST and go through the wickets with them again. This time the girl does not know what to do and is clearly completely unknowledgeable about the product, mush less how to troubleshoot it, and instead she is simply following a script. Another hour wasted. After being put on hold for the 4th or 5th time for 15 minutes, I simply hang up. (Realizing later that this is an intentional strategy.)
I call again. Now I am speaking to some guy in India. He does not know what he is doing either and tries to guide me through the support menu on the printer itself, but his script does not match the menu options on the printer. Back to the 15 minute intervals of hold broken up by him saying "one minute please sir while I verify some information". Another hour wasted, until I finally begin to realize that none of these people know what to do.
Still I call back and get another guy who leads me into the Support menu (press the return button 4 times to access this menu) . The he has me go to the Reports Menu and select the "print mech button tap" option, which prints out a 2 page "Printer Hardware" printout. He asks me to "give him the numbers on the document, but the document has all sorts of numbers on it from serial numbers to product numbers to other numbers with labels that are simply abbreviations. I ask him which numbers he needs from the two pages full of numbers, and back on hold I go for 20 minutes. He comes back and says "the long number, there should be a long number". Well the longest number on the document is the Serial number which I have already given during the initial information polling he did and so I ask him if he needs it again. Back on hold i go for another 20 minutes. Now the 15-20 minute hold cycle resumes, with him "checking something" and he will "be right back". Eventually he simply clicks over to see if I am still on the line and immediately puts me back on hold without saying anything. I put my phone on speaker and I wait him out, having already wasted an entire morning and half my afternoon.
Now this was the best part....HE BEGINS TO PRETEND LIKE HE IS HAVING MICROPHONE PROBLEMS AND CANNOT HEAR ME (yes I know, what does his microphone have to do with hearing me, I had the same thought). It is obvious he has simply either taken his headset off his head or moved the mic far away from his mouth and is pretending he can't hear me and that he will call me back and asks for my number. I ask him how is he going to hear me tell him my number (which by the way he already took at the beginning of the conversation) and he continues his ruse. So I hang up. It is obvious he doesnt know what to do and no one else there is going to help me.
Now I call back tonight around 930PM EST, and I get the Phillipines again. I go trough the whole polling phase with the girl and explain to her that I need the regionalization reset performed, and that all I need is to know which numbers of my printer to give to HP Support so that they can give me the code I need to reset this device. I politely tell her that I understand if she does not know what to do or understand what the procedure is and that I will not be angry with her if she is simply honest and tells me so, but that I want her to tell me if there is anyone there where she works who will definitely know how to do the reset, a supervisor or actual technical advisor, anybody. She is friendly and honest and says this is the frst time she has heard of this and she will ask what to do. Back on hold for 5 or 10 minutes. She claims she is looking in her "resources" for the way to do this. Nothing. I ask her to please stop and get her supervisor, she claims she is checking with her supervisor and that they are "checking the resources" for the procedure to reset regionalization. I foolishly think we are making progress.
After 20 minutes of her constantly telling me she is checking her resources, even after I have told her what the procedure entails and that all she needs to do is find the procedure and tell me which numbers it requires from the device itself in order to provide the reset code, I tell her to stop what she is doing and put her supervisor on the phone. She stalls. She says she is sorry but they have never heard of this procedure before and that she will schedule me a call-back for tomorrow. YEAH RIGHT. I ask her WHO is going to call me tomorrow? She replies that it will be them and that they will have the answer. I tell her that I already heard that from them the night before and I dont have another day to be wasted. I tell her to put her supervisor on the phone and I want the name of whoever is in charge of her office. She tries to ignore me and continues to ask for my phone number (which she already has). I press her for the name of who is in charge and she finally claims "Peter" is the supervisor. I tell her to put "Peter" on the phone. 10 minutes of hold and later a guy picks up the line, claims he is "Peter" and asks how I am doing. I politely say I am well and I ask him for his last name. He asks why I need his last name. i repeat my question, "What is your last name Peter?"..........his reply? "hello, sir? I am having trouble hearing you, can you hear me?" He begins to play with the microphone and puts me on hold. Each time he picks up and asks if I am there I immediately ask him for his last name, to which he resumes the ruse that he cannot hear me. I stay on the line. At this point it appears that HP must have some sort of policy where their "Support" personnel are not allowed to hang up the phone first, perhaps it is even tracked as a half-assed internal method of "Quality Assurance", and these people know it and this is why they will leave you on hold for ever and wait until you hang up. So, I wait Peter out for about 10 minutes, I am not on hold because there is no music, the microphone is simply muted. I tell him i know he is there and can hear me, and that i know he cannot hang up first, and then he promptly hangs up.
SO, my question....
NOW WHAT?
How does anything get escalated at HP when their overseas "Support" doesn't know what to do?
I live in Miami and there is a corporate headquarters there for HP Latin America. I am thinking of walking right into the lobby and finding someone with authority, but in all honesty I just want the d*** printer region reset so I can use these ink cartridges I already bought and opened.
Suggestions?

Hi,http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03149924&cc=uk&dlc=en&lc=en#N89
First, I am sorry to see your experience, however be aware that this forum is a peer-to-peer community and not a direct contact with HP.
To clarify, the product specification do list the ink cartridges regionalization, the specifications itself reffer to HP Suresupply to locate the ink cartridges for your region, as well as the following document which clearly state that information:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03239171&tmp_task=prodinfoCategory&cc=uk&dlc=en...
Firs be sure to have the latest software installed prior contacting HP support, which should be listed as 28
You may find that information listed in the following document (Check the How can I tell which driver version I have? section), if you have any older version be sure to uninstall it and install the latest software, as listed within the same document:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03149924&cc=uk&dlc=en&lc=en#N89
If you need, the latest software can be found below:
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-108821-3&cc=uk&dlc=en&lc=en...
Next ensure you have any of the 564 ink cartridges, once the printer being reset it require all the 4 ink cartridges to work
Finally check the private messages I sent you prior contacting HP support , the envelope icon at the top-right part of that screen.
The ensure you use the correct contact details lease double chekc it below:
http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1
Regards,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Reset PMU... mouse still stuck..now what?

Similar Messages

Maybe you are looking for