Restore iPod in DFU mode?
Hey their Apple communities
I have an iPod touch that definantly has viruses on it. I want to restore and update. If I were to enter DFU mode would this stop the viruses fro transfering to my computer? Also, after I done this would the viruses be completely wiped off my iPod?
Thanks and I hope you can answer my question
No, don't wipe it. If it definitely has viruses on it then it is probably a valuable historical artifact because it would likely be the first.
What proof-positive do you have that it has a virus?
Similar Messages
-
okay, so i put my ipod in DFU mode to restore it. well now it is in the middle of restoring ipod software and the bar hasnt moved. what do i do?
- Cancel the restore. Force close iTunes if necessary. Disconnect the iPod and reboot the computer and try again.
- Next try on another computer
- Make an appointment at the Genius Bar of an Apple store. -
why does my ipod exits dfu mode in the middle of the restore
Does iTunes see the iPod? Was the restore successful that it is went through all the steps without errors?
-
My ipad mini 2 is not turning on. I tried to reset with the power/home buttons but it didnt work. I tried to restore it in DFU mode but it didnt work, i get error 4004. Please help me!
I also tried the ol' whacking 3 times trick...Didn't work to my surprise
-
What is the easiest way to restore my ipod back to factory specs. It has a red circle with a red x in the middle,please help me to fix my ipod, until now i can't use my ipod..i tried all the procedures in Restore ipod from disk mode but still not working, please help me...
If you are unable to get the iPod into Disk Mode to try and restore it, it's a very good indication, as mentioned in the article, that the iPod's hard drive is damaged and in need of replacement either by Apple or a third party repair company.
B-rock -
TS3694 How to restore ipad on dfu mode error 9?
Hi guys
Need help how to restore IPAd in dfu mode error 9?Hi guys
Need help how to restore IPAd in dfu mode error 9? -
Cant switch on
What happened before you placed it in DFU mode?
Does iTunes see the iPod?
Does iTunes anything when you connect the iPod to the computer?
You really have not given us enough information to help you. -
IPhone will not update (error code 1) will not restore even in DFU mode (error code 1)
I bought the iPhone 4S from a friend, and I came to wiping it manually from the handset, no problems found however during the initial steps the iPhone was unable to validate on the apple servers (with the carrier stuck on searching). So, I plugged the phone into my trusty laptop installed Itunes fresh and proceeded to restore. The process gets to the later part of the validation and throws up an Error Code 1.
I'm aware (from searches across the internet) that error code 1 is typically found in phones with tampered hardware/software e.g. Jailbreak, unlock etc. My friend is not tech savvy and doesnt have a clue about these things so I'm sure the phone is 'as is'.
So i proceeded to troubleshoot the issue:
I edited my hosts file to point to the apple validation server (and checked it allowed connections to gs.apple.com within my browser - successful).
Now as the handset is stuck in recovery mode (with the usb and apple logo) I tried to restore via regular Recovery mode - no sucess (error 1)
Entered the phone into DFU mode (which, in essence ALL of google preaches is the way to restore regardless of issue) same error occurred.
So i looked into 3rd party applications that could force it to restore or perhaps allow a functional end product.
Redsnow (latest edition only provides restore for up to iOS 6.1.somethingorother) that produced a dead end.
Pangu restore facility (latest edition for iOS 7/some 8 models) hanged at the same place as the apple loader.
I've tried flushing my DNS cache, and verified the Date/time on my computer and router is correct.
I refuse to accept the phone is nonfunctional but am rapidly running out of ideas as how to
a) restore it to the iOS it initially had
b) update it forcefully and have iOS 8
c) install a custom rom in the hope some fuctionality exists enough to restore it again.
Please inform me of any suggestions you might have,
regards Jack.
PS. Further information; This has been attempted on 2 seperate windows workstations both running windows 8.1 up to date.
The USB cable is an unofficial one but has caused no issues in the past on another iphone that ive restored.Do you have the latest version of iTunes? Did you check for anti-virus software? One of the sections talks about interference from anti-virus software and firewalls. Also, you should not have to make any changes to your Host file unless your computer has been used to jailbreak a phone. I worry because you were using a number of software applications that are designed for jailbreaking devices. Excerpt from this support document. Get help with iOS update and restore errors - Apple Support
Check for hardware issues
Related errors: 1, 3, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
These errors mean that your device or computer might have a hardware issue that stops the update or restore from completing.
Check that your security software and settings aren't blocking your device from communicating with the Apple update server.
Then try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
Make sure that your security software and settings are allowing communication between your device and update servers.
If you still see the error message when you update or restore, contact Apple support. -
When I put my ipod into DFU mode, does it lose all of the photos and songs?
Just wondering.
No, all of your data will stay on the iPod Touch
I have put my iPod Touch 2nd gen in and out of DFU mode at least 10 times. -
Hi, i am in really big trouble, as on the 28th i decided i shoul update my ipod software to IOS 5. I plugged it in and downloaded it but unfortunately as it was installing to the ipod, i thought it was taking a while, and decided to try to cancel it, and in the end i unplugged it. Then i started to worry when it got put in dfu mode, now itunes won't even recognise it! Windows recognises it being plugged in and unplugged, i have been trauling through loads of websites to find out how to help it. I have also tried restarting and shutting down my laptop. Please help. (ipod touch 4th generation)
Jailbreaking voids the Apple warranty and also means that you will not get any support from Apple, including from this Apple forum. Jailbreaking can't be discussed in this Apple forum.
Unauthorized modification of iOS has been a major source of instability, disruption of services, and other issues -
My iPhone 3GS restarts repeatedly. Cannot be restored even in DFU Mode Restore.
My iPhone 3GS crashed and restarted on its own while running the Pandora app while plugged into a USB and charging. After it would finish starting up, it would say "activation required", as well as showing "no service" where there should have been service available. It would then restart after about 30 seconds to a minute. It would do this repeatedly in an endless loop of restarts.
I tried to do the "DFU Mode Restore" by holding the power and home buttons for 10 seconds, then holding the home button only until it connected to iTunes. The phone did have the black screen, and iTunes told me that the phone was in recovery mode and needed to be restored to be usable. The restore seems to complete, but in the end it fails. It says, "the iPhone "Iphone" could not be restored. An unknown error has occured (1)." It just leaves me with a screen showing that I should connect to iTunes with a USB cable.
Also, it shows no information on the phone in iTunes (capacity, software version, and serial number all show up as "n/a").Hello chiropteromania,
Thanks for the question. Based on what you stated, it seems like you get an error when trying to restore an iPhone. I would recommend that you read these articles, they may be helpful in troubleshooting your issue.
Resolve iOS update and restore errors in iTunes
Resolve iOS update and restore errors
Check for hardware issues
Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
These errors mean that your device or computer may have a hardware issue that's preventing the update or restore from completing.
Check that your security software and settings aren't preventing your device from communicating with the Apple update server.
Then try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
Confirm that your security software and settings are allowing communication between your device and update servers.
If you still see the error message when you update or restore, contact Apple support.
Thanks for using Apple Support Communities.
Cheers,
Mario -
ITunes cannot restore iPod in recovery mode.
I connect the iPod, and iTunes recognizes instantly, and tells me that it has detected the iPod in recovery mode etc. Then I click Restore and it normally extracts restoring software, and then a window appears that it cannot sync.
http://www.geocities.com/jjcalzada2009/Picture2.jpgopen iTunes
-plug the iPod into the computer
-hold both sleep/wake and home button until iPod restarts.
-let go of of the sleep/wake button when you see Apple logo.
-continue to hold home button until iTunes pops up with recovery mode
-click yes, and your iPod will be restored to its factory settings. -
I tried to put my ipod in dfu mode and now it wont turn back on?
my ipod was diabled and it said i had to connect it to itunes. then i was told to put it into dfu mode. i tried to do that but now my ipod wont turn back on. HELP?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
ERROR 27 :: iPhone 5 16GB Won't Restore, Stuck in DFU mode
I continue to recieve error msg when trying to restore my iphone... (end of the loading iPhone firmware)
As you show my itunes updater logs
========================================
2014-02-14 14:46:09.341 [21904:15f8]: restore library built Jan 7 2014 at 02:02:33
2014-02-14 14:46:09.341 [21904:15f8]: iTunes: iTunes 11.1.4.62
2014-02-14 14:46:09.341 [21904:15f8]: iTunes: Software payload version: 11B554a
2014-02-14 14:46:09.341 [21904:15f8]: iTunes: Using MobileRestore state machine
[12:47:15.0372] Changing state from 'Idle' to 'Restoring'
[12:47:15.0372] requested restore behavior: Erase
[12:47:15.0373] requested variant: Erase
[12:47:15.0374] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:16.0006] amai: _AMAuthInstallBundleCreateServerRequestDictionary: withApTicket is True
[12:47:16.0007] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RestoreLogo" Digest = "<CFData 00E8ABE8 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0007] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RestoreDeviceTree" Digest = "<CFData 00E8AC30 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0008] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RestoreKernelCache" Digest = "<CFData 00E8AC78 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0009] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RestoreRamDisk" Digest = "<CFData 00E8C238 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0009] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "iBEC" Digest = "<CFData 00E8C1F0 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0010] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "iBSS" Digest = "<CFData 00E8BFF8 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0011] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "KernelCache" Digest = "<CFData 00E8C280 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0011] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryLow1" Digest = "<CFData 00E8C160 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0012] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryLow0" Digest = "<CFData 00E8C2C8 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0013] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "LLB" Digest = "<CFData 00E8C118 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0013] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "iBoot" Digest = "<CFData 00E8C040 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0014] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "DeviceTree" Digest = "<CFData 00E8C0D0 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0014] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryCharging1" Digest = "<CFData 00E8C1A8 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0015] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "AppleLogo" Digest = "<CFData 00E8C310 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0015] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryPlugin" Digest = "<CFData 00E8C358 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0016] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryFull" Digest = "<CFData 00E8C088 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0016] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryCharging0" Digest = "<CFData 0F4C8D08 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0017] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RecoveryMode" Digest = "<CFData 0F4C8C78 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[12:47:16.0018] amai: _AMAuthInstallBundleCreateServerRequestDictionary: using UniqueBuildID <CFData 05B9C328 [7497907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}
[12:47:16.0018] amai: AMAuthInstallRequestSendSync: SSO function returned NULL, SSO disabled.
[12:47:16.0018] amai: AMAuthInstallDebugWriteObject: debug object written: file://localhost/H:/Users/ABDULL~1/AppData/Local/Temp/Per2900.tmp/amai/debug/ts s-request.plist
[12:47:16.0714] amai: tss_submit_job: HttpQueryInfo returned 200
[12:47:16.0909] amai: AMAuthInstallRequestSendSync: received tss response (server version: 2.1.0)
[12:47:16.0914] amai: AMAuthInstallDebugWriteObject: debug object written: file://localhost/H:/Users/ABDULL~1/AppData/Local/Temp/Per2900.tmp/amai/debug/ts s-response.plist
[12:47:17.0251] amai: _AMAuthInstallBundlePopulatePersonalizedBundle: no entry in manifest found for "Diags"
[12:47:17.0313] iBoot build-version = iBoot-1940.3.5
[12:47:17.0314] iBoot build-style = RELEASE
[12:47:17.0316] requested restore behavior: Erase
[12:47:17.0318] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:17.0320] requested restore behavior: Erase
[12:47:17.0324] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:17.0325] unable to open device_map.txt: No such file or directory
[12:47:17.0327] found device map entry for 0x00008950 0x00000002. boardConfig=n42ap platform=s5l8950x
[12:47:17.0328] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[12:47:17.0330] AMDeviceIoControl: GetOverlappedResult failed
[12:47:17.0330] AMDeviceIoControl: pipe stall
[12:47:17.0331] USBControlTransfer: error 31, usbd status c0000004
[12:47:17.0332] command device request for 'getenv radio-error' failed: 2008
[12:47:17.0333] radio-error not set
[12:47:17.0334] unable to open device_map.txt: No such file or directory
[12:47:17.0335] <Recovery Mode Device 0712ECA0>: production fused device
[12:47:17.0336] requested restore behavior: Erase
[12:47:17.0337] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:17.0338] requested restore behavior: Erase
[12:47:17.0338] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:17.0339] interface has 1 endpoints, file pipe = 1
[12:47:17.0339]
[12:47:17.0340] <Recovery Mode Device 0712ECA0>: operation 4 progress -1
[12:47:17.0382] bootstrapping restore with iBEC
[12:47:17.0383] requested restore behavior: Erase
[12:47:17.0385] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:17.0395] <Recovery Mode Device 0712ECA0>: operation 31 progress -1
[12:47:18.0396] <Recovery Mode Device 0712ECA0>: Recovery mode succeeded
[12:47:18.0397] Finished Recovery Restore Phase: Successful
[12:47:18.0520] Recovery mode device disconnected
[12:47:18.0522] Device removed when in state Restoring, moving device to transition state
[12:47:18.0523] Changing state from 'Restoring' to 'Transitioning'
[12:47:18.0524] Creating timer to monitor transition
[12:47:20.0554] Recovery mode device connected
[12:47:20.0555] Transitioning device returned, continuing restore.
[12:47:20.0555] Canceling timer
[12:47:20.0556] Changing state from 'Transitioning' to 'Restoring'
[12:47:20.0556] requested restore behavior: Erase
[12:47:20.0557] requested variant: Erase
[12:47:20.0557] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:21.0042] amai: _AMAuthInstallBundleCreateServerRequestDictionary: withApTicket is False
[12:47:21.0043] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreLogo"
[12:47:21.0044] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreDeviceTree"
[12:47:21.0045] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreKernelCache"
[12:47:21.0045] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreRamDisk"
[12:47:21.0046] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "iBEC"
[12:47:21.0046] amai: _AMAuthInstallBundleCreateServerRequestDictionary: entry "iBSS" has been previously personalized; skipping it
[12:47:21.0047] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "KernelCache"
[12:47:21.0048] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryLow1"
[12:47:21.0048] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryLow0"
[12:47:21.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: entry "LLB" has been previously personalized; skipping it
[12:47:21.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "iBoot"
[12:47:21.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "DeviceTree"
[12:47:21.0050] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryCharging1"
[12:47:21.0050] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "AppleLogo"
[12:47:21.0050] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryPlugin"
[12:47:21.0051] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryFull"
[12:47:21.0052] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryCharging0"
[12:47:21.0052] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RecoveryMode"
[12:47:21.0053] amai: _AMAuthInstallBundleCreateServerRequestDictionary: nothing to be done
[12:47:21.0053] iBoot build-version = iBoot-1940.3.5
[12:47:21.0054] iBoot build-style = RELEASE
[12:47:21.0054] requested restore behavior: Erase
[12:47:21.0054] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:21.0055] requested restore behavior: Erase
[12:47:21.0056] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:21.0057] unable to open device_map.txt: No such file or directory
[12:47:21.0057] found device map entry for 0x00008950 0x00000002. boardConfig=n42ap platform=s5l8950x
[12:47:21.0058] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[12:47:21.0059] AMDeviceIoControl: GetOverlappedResult failed
[12:47:21.0059] AMDeviceIoControl: pipe stall
[12:47:21.0059] USBControlTransfer: error 31, usbd status c0000004
[12:47:21.0060] command device request for 'getenv radio-error' failed: 2008
[12:47:21.0060] radio-error not set
[12:47:21.0061] unable to open device_map.txt: No such file or directory
[12:47:21.0061] <Recovery Mode Device 0712E8E8>: production fused device
[12:47:21.0062] requested restore behavior: Erase
[12:47:21.0062] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:21.0063] requested restore behavior: Erase
[12:47:21.0063] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:21.0063] interface has 1 endpoints, file pipe = 1
[12:47:21.0063]
[12:47:21.0064] <Recovery Mode Device 0712E8E8>: operation 4 progress -1
[12:47:21.0104] unable to open device_map.txt: No such file or directory
[12:47:21.0105] found device map entry for 0x00008950 0x00000002. boardConfig=n42ap platform=s5l8950x
[12:47:21.0106] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[12:47:21.0106] requested restore behavior: Erase
[12:47:21.0107] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:21.0108] requested restore behavior: Erase
[12:47:21.0109] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:21.0109] <Recovery Mode Device 0712E8E8>: operation 42 progress -1
[12:47:21.0110] requested restore behavior: Erase
[12:47:21.0111] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:22.0137] <Recovery Mode Device 0712E8E8>: operation 5 progress -1
[12:47:22.0372] unable to open device_map.txt: No such file or directory
[12:47:22.0374] found device map entry for 0x00008950 0x00000002. boardConfig=n42ap platform=s5l8950x
[12:47:22.0375] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[12:47:22.0377] AMDeviceIoControl: GetOverlappedResult failed
[12:47:22.0377] AMDeviceIoControl: pipe stall
[12:47:22.0378] USBControlTransfer: error 31, usbd status c0000004
[12:47:22.0380] command device request for 'getenv ramdisk-delay' failed: 2008
[12:47:24.0036] <Recovery Mode Device 0712E8E8>: operation 6 progress -1
[12:47:25.0047] <Recovery Mode Device 0712E8E8>: operation 7 progress -1
[12:47:25.0260] <Recovery Mode Device 0712E8E8>: operation 8 progress -1
[12:47:25.0261] unable to open device_map.txt: No such file or directory
[12:47:25.0263] found device map entry for 0x00008950 0x00000002. boardConfig=n42ap platform=s5l8950x
[12:47:25.0264] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[12:47:25.0265] <Recovery Mode Device 0712E8E8>: operation 9 progress -1
[12:47:25.0266] <Recovery Mode Device 0712E8E8>: Recovery mode succeeded
[12:47:25.0267] Finished Recovery Restore Phase: Successful
[12:47:26.0474] Recovery mode device disconnected
[12:47:26.0474] Device removed when in state Restoring, moving device to transition state
[12:47:26.0475] Changing state from 'Restoring' to 'Transitioning'
[12:47:26.0477] Creating timer to monitor transition
[12:47:28.0609] RestoreOS mode device connected
[12:47:28.0610] Transitioning device returned, continuing restore.
[12:47:28.0610] Canceling timer
[12:47:28.0611] Changing state from 'Transitioning' to 'Restoring'
[12:47:28.0614] <Restore Device 00E4C4C0>: operation 44 progress -1
[12:47:28.0615] requested restore behavior: Erase
[12:47:28.0616] requested variant: Erase
[12:47:28.0616] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:29.0096] amai: _AMAuthInstallBundleCreateServerRequestDictionary: withApTicket is False
[12:47:29.0097] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreLogo"
[12:47:29.0097] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreDeviceTree"
[12:47:29.0098] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreKernelCache"
[12:47:29.0099] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreRamDisk"
[12:47:29.0099] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "iBEC"
[12:47:29.0100] amai: _AMAuthInstallBundleCreateServerRequestDictionary: entry "iBSS" has been previously personalized; skipping it
[12:47:29.0100] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "KernelCache"
[12:47:29.0101] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryLow1"
[12:47:29.0101] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryLow0"
[12:47:29.0102] amai: _AMAuthInstallBundleCreateServerRequestDictionary: entry "LLB" has been previously personalized; skipping it
[12:47:29.0103] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "iBoot"
[12:47:29.0103] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "DeviceTree"
[12:47:29.0103] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryCharging1"
[12:47:29.0104] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "AppleLogo"
[12:47:29.0104] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryPlugin"
[12:47:29.0105] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryFull"
[12:47:29.0105] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryCharging0"
[12:47:29.0106] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RecoveryMode"
[12:47:29.0106] amai: _AMAuthInstallBundleCreateServerRequestDictionary: nothing to be done
[12:47:29.0107] requested restore behavior: Erase
[12:47:29.0107] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:29.0108] device did not return saved USB log
[12:47:29.0108] device did not return saved panic log
[12:47:29.0109] previous restore failed with exit status 0x100
[12:47:29.0109] connected to service com.apple.mobile.restored
[12:47:29.0109] using protocol version 13
[12:47:29.0110] unable to open device_map.txt: No such file or directory
[12:47:29.0110] board config = n42ap
[12:47:29.0111] no value returned for BootArgs
[12:47:29.0111] _copyDeviceProperty() failed for restore bootargs
[12:47:29.0113] no value returned for MarketingPartNumber
[12:47:29.0113] _copyDeviceProperty() failed for mpn
[12:47:29.0114] requested restore behavior: Erase
[12:47:29.0115] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[12:47:29.0117] value query for 'HardwareModel' returned 'N42AP'
[12:47:39.0127] <Restore Device 00E4C4C0>: operation 28 progress -1
[12:47:52.0192] previous restore failed: rial Port on ARM Device=uart1 at 0x32600000(0x8d46d000)
[12:47:52.0192] [IOFlashPartitionScheme:INIT ] probing with score 4[nand_part_core:INF@2173] read valid partition table
[12:47:52.0192] [nand_part_core:INF@ 145] created partition 0 as 'Boot Block'
[12:47:52.0192] [nand_part_core:INF@ 145] created partition 1 as 'Effaceable'
[12:47:52.0192] [nand_part_core:INF@ 145] created partition 2 as 'NVRAM'
[12:47:52.0192] [nand_part_core:INF@ 145] created partition 3 as 'Firmware'
[12:47:52.0192] [nand_part_core:INF@ 145] created partition 4 as 'Filesystem'
[12:47:52.0192] [nand_part_core:INF@ 157] published partition 4
[12:47:52.0192] [nand_part_core:INF@ 145] created partition 5 as 'System Config'
[12:47:52.0192] com.apple.AppleFSCompressionTypeZlib load succeeded
[12:47:52.0192] AppleSwissPPNFTL started with IOFlashStoragePartition provider
[12:47:52.0192] [NAND] _FindFlashMediaAndKeepout:601 physical nand block offset 1
[12:47:52.0192] AppleNANDFTL registered[nand_part_core:INF@ 145] created partition 6 as 'Diagnostic Data'
[12:47:52.0192] [nand_part_core:INF@ 145] created partition 7 as 'Bad Block Table'
[12:47:52.0192] [NAND] start:356 this 0x9076d400 PROVIDER=0x907a2c80 flashMedia=0x907a2c80
[12:47:52.0192] L2TP domain init
[12:47:52.0192] L2TP domain init complete
[12:47:52.0192] PPTP domain init
[12:47:52.0192] [NAND] WMR_Start:149 Apple PPN NAND Driver, Read/Write
[12:47:52.0192] [NAND] WMR_Start:174 FIL_Init [OK]
[12:47:52.0192] Scaler 0 enableDeviceClock(true,HALF_CLOCK_INDEX) = 0x0
[12:47:52.0192] Scaler 0 enableDeviceClock(true,FULL_CLOCK_INDEX) = 0x0
[12:47:52.0192] Scaler 0 enableDevicePower(true,0,HALF_CLOCK_INDEX) = 0x0
[12:47:52.0192] Scaler 0 enableDeviceClock(false,FULL_CLOCK_INDEX) = 0x0
[12:47:52.0192] AppleMultitouchN1SPI: successfully started
[12:47:52.0192] Scaler 1 enableDeviceClock(true,HALF_CLOCK_INDEX) = 0x0
[12:47:52.0192] Scaler 1 enableDeviceClock(true,FULL_CLOCK_INDEX) = 0x0
[12:47:52.0192] Scaler 1 enableDevicePower(true,0,HALF_CLOCK_INDEX) = 0x0
[12:47:52.0192] [nand_part_core:INF@ 157] published partition 7
[12:47:52.0192] Scaler 1 enableDeviceClock(false,FULL_CLOCK_INDEX) = 0x0
[12:47:52.0192] AppleD1972PMUPowerSource: AppleUSBCableDetect 1
[12:47:52.0192] [NAND] WMR_Open:371 VFL_Open [OK]
[12:47:52.0192] AppleAP3DSH::probe found device with ID: 0x3f
[12:47:52.0192] AppleAP3DSH::handleStart _calibrationMatrix [65044 -1766 -685] [-927 66132 -215] [379 250 66155]
[12:47:52.0192] AppleAP3DSH::handleStart _calibrationOffsets [-446256 834666 2479123]
[12:47:52.0192] AppleAP3DSH::handleStart - No calibration inverse matrix or the data is invalid, Compute locally
[12:47:52.0192] AppleAP3DSH::handleStart _calibrationInverseMatrix [66053 1761 689] [924 64970 220] [-381 -256 64919]
[12:47:52.0192] AppleAP3DSH::handleStart _odr400HzSampleInterval = 2418
[12:47:52.0192] AppleD1972PMUPowerSource: AppleUSBCableType USBHost
[12:47:52.0192] AppleH4CamIn::start - back camera expected
[12:47:52.0192] AppleH4CamIn::start - front camera expected
[12:47:52.0192] AppleH4CamIn::power_off_hardware
[12:47:52.0192] AppleH4CamIn::setPowerStateGated: 0
[12:47:52.0192] virtual bool AppleDisplayPipe::start_hardware(IOService *), auto-detect chip
[12:47:52.0192] AppleSynopsysOTGDevice::gated_handleUSBCableConnect cable connected, but don't have device configuration yet
[12:47:52.0192] AppleCS35L19Amp: could not allocate control 395
[12:47:52.0192] AppleSynopsysOTGDevice::gated_handleUSBCableConnect cable connected, but don't have device configuration yet
[12:47:52.0192] AppleMultitouchN1SPI: detected HBPP. driver will be kept alive
[12:47:52.0192] display-scale = 2
[12:47:52.0192] display-rotation = 0
[12:47:52.0192] found applelogo at /usr/share/progressui/[email protected]
[12:47:52.0192] found display: primary
[12:47:52.0192] display: 640 x 1136
[12:47:52.0192] found PTP interface
[12:47:52.0192] AppleSynopsysOTGDevice - Configuration: PTP
[12:47:52.0192] AppleSynopsysOTGDevice Interface: PTP
[12:47:52.0192] AppleSynopsysOTGDevice - Configuration: iPod USB Interface
[12:47:52.0192] AppleSynopsysOTGDevice Interface: USBAudioControl
[12:47:52.0192] AppleSynopsysOTGDevice Interface: USBAudioStreaming
[12:47:52.0192] AppleSynopsysOTGDevice Interface: IapOverUsbHid
[12:47:52.0192] AppleSynopsysOTGDevice - Configuration: PTP + Apple Mobile Device
[12:47:52.0192] AppleSynopsysOTGDevice Interface: PTP
[12:47:52.0192] AppleSynopsysOTGDevice Interface: AppleUSBMux
[12:47:52.0192] AppleSynopsysOTGDevice - Configuration: PTP + Apple Mobile Device + Apple USB Ethernet
[12:47:52.0192] AppleSynopsysOTGDevice Interface: PTP
[12:47:52.0192] AppleSynopsysOTGDevice Interface: AppleUSBMux
[12:47:52.0192] AppleSynopsysOTGDevice Interface: AppleUSBEthernet
[12:47:52.0192] AppleSynopsysOTGDevice::gated_registerFunction Register function USBAudioControl
[12:47:52.0192] IOAccessoryPortUSB::start
[12:47:52.0192] virtual bool AppleUSBDeviceMux::start(IOService *) build: Sep 27 2013 23:30:36
[12:47:52.0192] init_waste
[12:47:52.0192] AppleSynopsysOTGDevice::gated_registerFunction Register function AppleUSBMux
[12:47:52.0192] AppleSynopsysOTGDevice::gated_registerFunction Register function IapOverUsbHid
[12:47:52.0192] AppleSynopsysOTGDevice::gated_registerFunction Register function USBAudioStreaming
[12:47:52.0192] AppleSynopsysOTGDevice::gated_registerFunction Register function AppleUSBEthernet
[12:47:52.0192] AppleSynopsysOTGDevice::gated_registerFunction Register function PTP
[12:47:52.0192] AppleSynopsysOTGDevice::startUSBStack Starting usb stack
[12:47:52.0192] IOReturn AppleUSBDeviceMux::setPropertiesGated(OSObject *) setting debug level to 7
[12:47:52.0192] 000123.268755 wlan.N[0] AppleBCMWLANBusInterfaceHSIC::attachBusGated(): AppleBCMWLANBusInterfaceHSIC (0x916a5000) -->>-- AppleBCMWLANBusInterfaceHSICShim (0x92e43c00)
[12:47:52.0192] AppleBCMWLANCore::init(): IO80211-40 Sep 27 2013 22:57:52
[12:47:52.0192] AppleBCMWLANCore::init(): AppleBCMWLANV2-249.2 Sep 27 2013 23:32:48 release
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f05948 established 62078<-lo0->49152 62078<-usb->17920
[12:47:52.0192] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x92f05948
[12:47:52.0192] recv(13, 4) failed: connection closed
[12:47:52.0192] unable to read message size: -1
[12:47:52.0192] could not receive message
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f05948 established 62078<-lo0->49153 62078<-usb->18176
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f058f0 established 62078<-lo0->49154 62078<-usb->18432
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f05898 established 62078<-lo0->49155 62078<-usb->18688
[12:47:52.0192] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x92f05948
[12:47:52.0192] recv(13, 4) failed: connection closed
[12:47:52.0192] unable to read message size: -1
[12:47:52.0192] could not receive message
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f05948 established 62078<-lo0->49156 62078<-usb->18944
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f05840 established 62078<-lo0->49157 62078<-usb->19200
[12:47:52.0192] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x92f05898
[12:47:52.0192] recv(15, 4) failed: connection closed
[12:47:52.0192] unable to read message size: -1
[12:47:52.0192] could not receive message
[12:47:52.0192] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x92f05948
[12:47:52.0192] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x92f05840
[12:47:52.0192] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x92f058f0
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f058f0 established 62078<-lo0->49158 62078<-usb->19456
[12:47:52.0192] recv(13, 4) failed: connection closed
[12:47:52.0192] unable to read message size: -1
[12:47:52.0192] could not receive message
[12:47:52.0192] recv(16, 4) failed: connection closed
[12:47:52.0192] unable to read message size: -1
[12:47:52.0192] could not receive message
[12:47:52.0192] recv(14, 4) failed: connection closed
[12:47:52.0192] unable to read message size: -1
[12:47:52.0192] could not receive message
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f05840 established 62078<-lo0->49159 62078<-usb->19712
[12:47:52.0192] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x92f05840
[12:47:52.0192] recv(14, 4) failed: connection closed
[12:47:52.0192] unable to read message size: -1
[12:47:52.0192] could not receive message
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f05840 established 62078<-lo0->49160 62078<-usb->19968
[12:47:52.0192] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x92f05840
[12:47:52.0192] recv(14, 4) failed: connection closed
[12:47:52.0192] unable to read message size: -1
[12:47:52.0192] could not receive message
[12:47:52.0192] 000123.374285 wlan.N[1] AppleBCMWLANCore::start(): Starting with MAC Address: <<<mac address>>>
[12:47:52.0192] 000123.374664 wlan.N[2] AppleBCMWLANCore::setPowerStateGated(): powerState 1, fStateFlags 0x20, dev 0xcef28000 (this 1, provider 0)
[12:47:52.0192] 000123.374678 wlan.N[3] AppleBCMWLANCore::setPowerStateGated(): Received power state change before driver has initialized, ignoring
[12:47:52.0192] IO80211Peer::addPhyStatistics Phy stats started for addr <<<mac address>>>
[12:47:52.0192] IO80211Peer::addPhyStatistics Tx Completion stats started for addr <<<mac address>>>
[12:47:52.0192] IO80211PeerManager::initWithInterface cant add monitoring timer
[12:47:52.0192] Started logging for intf
[12:47:52.0192] IO80211PeerManager::initWithInterface: inited peer manager
[12:47:52.0192] IO80211Interface::init peerManager=0x9167f000
[12:47:52.0192] start:156
[12:47:52.0192] start:156
[12:47:52.0192] [NAND] WMR_Open:420 FTL_Open [OK]
[12:47:52.0192] [NAND] _publishServices:642 FTL capabilities: 0x00000001
[12:47:52.0192] [NAND] _ppnvflGetStruct:3469 Checking borrowed blocks - count: 23 max_count: 23
[12:47:52.0192] [NAND] _fetchBorrowedList:881 number of borrowed blocks 16
[12:47:52.0192] [nand_part_core:INF@ 157] published partition 0
[12:47:52.0192] [nand_part_core:INF@ 157] published partition 1
[12:47:52.0192] [nand_part_core:INF@ 157] published partition 2
[12:47:52.0192] [nand_part_core:INF@ 157] published partition 3
[12:47:52.0192] [nand_part_core:INF@ 157] published partition 5
[12:47:52.0192] [nand_part_core:INF@ 157] published partition 6
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f050b0 established 62078<-lo0->49161 62078<-usb->20224
[12:47:52.0192] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x92f050b0
[12:47:52.0192] recv(9, 4) failed: connection closed
[12:47:52.0192] unable to read message size: -1
[12:47:52.0192] could not receive message
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f050b0 established 62078<-lo0->49162 62078<-usb->20480
[12:47:52.0192] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x92f050b0
[12:47:52.0192] recv(9, 4) failed: connection closed
[12:47:52.0192] unable to read message size: -1
[12:47:52.0192] could not receive message
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f050b0 established 62078<-lo0->49163 62078<-usb->20736
[12:47:52.0192] unrecognized key 'BootArgs' in value query
[12:47:52.0192] failed to handle value query for key 'BootArgs', sending back empty response
[12:47:52.0192] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x92f050b0
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f050b0 established 62078<-lo0->49164 62078<-usb->20992
[12:47:52.0192] recv(9, 4) failed: connection closed
[12:47:52.0192] unable to read message size: -1
[12:47:52.0192] could not receive message
[12:47:52.0192] unrecognized key 'MarketingPartNumber' in value query
[12:47:52.0192] failed to handle value query for key 'MarketingPartNumber', sending back empty response
[12:47:52.0192] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x92f050b0
[12:47:52.0192] recv(14, 4) failed: connection closed
[12:47:52.0192] unable to read message size: -1
[12:47:52.0192] could not receive message
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x92f050b0 established 62078<-lo0->49165 62078<-usb->21248
[12:47:52.0192] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x92f050b0
[12:47:52.0192] client protocol version 13
[12:47:52.0192] recv(9, 4) failed: connection closed
[12:47:52.0192] unable to read message size: -1
[12:47:52.0192] could not receive message
[12:47:52.0192] *** UUID A8E00E75-4D25-6A4A-BB48-9F3FA7071E50 ***
[12:47:52.0192] Restore options:
[12:47:52.0192] UUID => <CFString 0x15e3bb00 [0x369ad0]>{contents = "A8E00E75-4D25-6A4A-BB48-9F3FA7071E50"}
[12:47:52.0192] MinimumSystemPartition => <CFNumber 0x15e3ba50 [0x369ad0]>{value = +1589, type = kCFNumberSInt64Type}
[12:47:52.0192] SystemPartitionSize => <CFNumber 0x15e3d3b0 [0x369ad0]>{value = +1589, type = kCFNumberSInt64Type}
[12:47:52.0192] SystemPartitionPadding => <CFBasicHash 0x15e3bb30 [0x369ad0]>{type = mutable dict, count = 5,
[12:47:52.0192] entries =>
[12:47:52.0192] 2 : <CFString 0x15e3ba80 [0x369ad0]>{contents = "128"} = <CFNumber 0x15e3bab0 [0x369ad0]>{value = +1280, type = kCFNumberSInt64Type}
[12:47:52.0192] 3 : <CFString 0x15e3cbe0 [0x369ad0]>{contents = "16"} = <CFNumber 0x15e3bb60 [0x369ad0]>{value = +160, type = kCFNumberSInt64Type}
[12:47:52.0192] 4 : <CFString 0x15e3ba20 [0x369ad0]>{contents = "32"} = <CFNumber 0x15e3d180 [0x369ad0]>{value = +320, type = kCFNumberSInt64Type}
[12:47:52.0192] 5 : <CFString 0x15e3b770 [0x369ad0]>{contents = "8"} = <CFNumber 0x15e3b6b0 [0x369ad0]>{value = +80, type = kCFNumberSInt64Type}
[12:47:52.0192] 8 : <CFString 0x15e3b7a0 [0x369ad0]>{contents = "64"} = <CFNumber 0x15e3b760 [0x369ad0]>{value = +640, type = kCFNumberSInt64Type}
[12:47:52.0192] }
[12:47:52.0192]
[12:47:52.0192] entering load_sep_os
[12:47:52.0192] device has no sep
[12:47:52.0192] entering partition_nand_device
[12:47:52.0192] device supports boot-from-NAND
[12:47:52.0192] nand device is already partitioned
[12:47:52.0192] entering wait_for_storage_device
[12:47:52.0192] Searching for NAND service
[12:47:52.0192] Found NAND service: IOFlashStoragePartition
[12:47:52.0192] NAND initialized. Waiting for devnode.
[12:47:52.0192] entering clear_remap_variable
[12:47:52.0192] waiting for matching IOKit service: <CFBasicHash 0x15d44000 [0x369ad0]>{type = mutable dict, count = 2,
[12:47:52.0192] entries =>
[12:47:52.0192] 0 : <CFString 0x160e98 [0x369ad0]>{contents = "IOResourceMatch"} = <CFString 0x15d44d70 [0x369ad0]>{contents = "IONVRAM"}
[12:47:52.0192] 2 : <CFString 0x4c2f00 [0x369ad0]>{contents = "IOProviderClass"} = <CFString 0x15d44d50 [0x369ad0]>{contents = "IOResources"}
[12:47:52.0192] }
[12:47:52.0192]
[12:47:52.0192] executing /usr/sbin/nvram
[12:47:52.0192] entering format_effaceable_storage
[12:47:52.0192] effaceable storage is formatted, clearing it
[12:47:52.0192] [effaceable:INIT] found current generation, 59, in group 2
[12:47:52.0192] [effaceable:INIT] started
[12:47:52.0192] [effaceable:INIT] started
[12:47:52.0192] effaceable storaged cleared
[12:47:52.0192] entering ramrod_probe_media
[12:47:52.0192] device partitioning scheme is GPT
[12:47:52.0192] find_filesystem_partitions: storage=/dev/disk0s1 system=/dev/disk0s1s1 data=/dev/disk0s1s2
[12:47:52.0192] executing /sbin/fsck_hfs
[12:47:52.0192] ** /dev/rdisk0s1s1
[12:47:52.0192] Executing fsck_hfs (version hfs-227).
[12:47:52.0192] ** Checking Journaled HFS Plus volume.
[12:47:52.0192] ** Detected a case-sensitive volume.
[12:47:52.0192] The volume name is InnsbruckTaos11B554a.N42OS
[12:47:52.0192] ** Checking extents overflow file.
[12:47:52.0192] ** Checking catalog file.
[12:47:52.0192] ** Checking multi-linked files.
[12:47:52.0192] ** Checking catalog hierarchy.
[12:47:52.0192] ** Checking extended attributes file.
[12:47:52.0192] ** Checking volume bitmap.
[12:47:52.0192] ** Checking volume information.
[12:47:52.0192] ** Trimming unused blocks.
[12:47:52.0192] ** The volume InnsbruckTaos11B554a.N42OS appears to be OK.
[12:47:52.0192] executing /sbin/mount_hfs
[12:47:52.0192] /dev/disk0s1s1 mounted on /mnt1
[12:47:52.0192] entering check_for_restore_log
[12:47:52.0192] found restore log (size = 44403)
[12:47:52.0192] entering unmount_filesystems
[12:47:52.0192] error unmounting '/mnt2': Invalid argument
[12:47:52.0192] entering clean_NAND
[12:47:52.0192] NAND format complete
[12:47:52.0192] entering ramrod_probe_media
[12:47:52.0192] find_filesystem_partitions: storage=/dev/disk0 system= data=
[12:47:52.0192] entering format_storage_for_LwVM
[12:47:52.0192] entering ramrod_probe_media
[12:47:52.0192] device partitioning scheme is GPT
[12:47:52.0192] unexpected partition 'LwVM' - skipping
[12:47:52.0192] find_filesystem_partitions: storage=/dev/disk0s1 system= data=
[12:47:52.0192] entering create_filesystem_partitions
[12:47:52.0192] User specified system partition size, skipping firmware extras size.
[12:47:52.0192] system partition padding size is: 167772160 bytes
[12:47:52.0192] unable to open : No such file or directory
[12:47:52.0192] creating 2 partitions
[12:47:52.0192] creating encrypted data partition
[12:47:52.0192] entering ramrod_probe_media
[12:47:52.0192] device partitioning scheme is GPT
[12:47:52.0192] find_filesystem_partitions: storage=/dev/disk0s1 system=/dev/disk0s1s1 data=/dev/disk0s1s2
[12:47:52.0192] wipe entire partition: 1 (old = 0 new = 1749)
[12:47:52.0192] block size for /dev/disk0s1s1: 4096
[12:47:52.0192] /sbin/newfs_hfs -s -v System -J /dev/disk0s1s1
[12:47:52.0192] executing /sbin/newfs_hfs -s -v System -J /dev/disk0s1s1
[12:47:52.0192] Initialized /dev/rdisk0s1s1 as a 2 GB case-sensitive HFS Plus volume with a 8192k journal
[12:47:52.0192] block size for /dev/disk0s1s2: 4096
[12:47:52.0192] /sbin/newfs_hfs -s -v Data -J -P /dev/disk0s1s2
[12:47:52.0192] executing /sbin/newfs_hfs -s -v Data -J -P /dev/disk0s1s2
[12:47:52.0192] Initialized /dev/rdisk0s1s2 as a 13 GB case-sensitive HFS Plus volume with a 8192k journal
[12:47:52.0192] entering ramrod_probe_media
[12:47:52.0192] device partitioning scheme is GPT
[12:47:52.0192] find_filesystem_partitions: storage=/dev/disk0s1 system=/dev/disk0s1s1 data=/dev/disk0s1s2
[12:47:52.0192] entering mount_filesystems
[12:47:52.0192] executing /sbin/fsck_hfs
[12:47:52.0192] ** /dev/rdisk0s1s1
[12:47:52.0192] Executing fsck_hfs (version hfs-227).
[12:47:52.0192] ** Checking Journaled HFS Plus volume.
[12:47:52.0192] ** Detected a case-sensitive volume.
[12:47:52.0192] The volume name is System
[12:47:52.0192] ** Checking extents overflow file.
[12:47:52.0192] ** Checking catalog file.
[12:47:52.0192] ** Checking multi-linked files.
[12:47:52.0192] ** Checking catalog hierarchy.
[12:47:52.0192] ** Checking extended attributes file.
[12:47:52.0192] ** Checking volume bitmap.
[12:47:52.0192] ** Checking volume information.
[12:47:52.0192] ** Trimming unused blocks.
[12:47:52.0192] ** The volume System appears to be OK.
[12:47:52.0192] executing /sbin/mount_hfs
[12:47:52.0192] /dev/disk0s1s1 mounted on /mnt1
[12:47:52.0192] executing /sbin/fsck_hfs
[12:47:52.0192] ** /dev/rdisk0s1s2
[12:47:52.0192] Executing fsck_hfs (version hfs-227).
[12:47:52.0192] ** Checking Journaled HFS Plus volume.
[12:47:52.0192] ** Detected a case-sensitive volume.
[12:47:52.0192] The volume name is Data
[12:47:52.0192] ** Checking extents overflow file.
[12:47:52.0192] ** Checking catalog file.
[12:47:52.0192] ** Checking multi-linked files.
[12:47:52.0192] ** Checking catalog hierarchy.
[12:47:52.0192] ** Checking extended attributes file.
[12:47:52.0192] ** Checking volume bitmap.
[12:47:52.0192] ** Checking volume information.
[12:47:52.0192] ** Trimming unused blocks.
[12:47:52.0192] ** The volume Data appears to be OK.
[12:47:52.0192] executing /sbin/mount_hfs
[12:47:52.0192] /dev/disk0s1s2 mounted on /mnt2
[12:47:52.0192] entering resize_system_partition_to_options
[12:47:52.0192] User specified system partition size, skipping firmware extras size.
[12:47:52.0192] Found SystemPartitionPadding value of 167772160 bytes
[12:47:52.0192] Erasing system partition prior to resize operation.
[12:47:52.0192] block size for /dev/disk0s1s1: 4096
[12:47:52.0192] /sbin/newfs_hfs -s -v System -J /dev/disk0s1s1
[12:47:52.0192] executing /sbin/newfs_hfs -s -v System -J /dev/disk0s1s1
[12:47:52.0192] Initialized /dev/rdisk0s1s1 as a 2 GB case-sensitive HFS Plus volume with a 8192k journal
[12:47:52.0192] executing /sbin/fsck_hfs
[12:47:52.0192] ** /dev/rdisk0s1s1
[12:47:52.0192] Executing fsck_hfs (version hfs-227).
[12:47:52.0192] ** Checking Journaled HFS Plus volume.
[12:47:52.0192] ** Detected a case-sensitive volume.
[12:47:52.0192] The volume name is System
[12:47:52.0192] ** Checking extents overflow file.
[12:47:52.0192] ** Checking catalog file.
[12:47:52.0192] ** Checking multi-linked files.
[12:47:52.0192] ** Checking catalog hierarchy.
[12:47:52.0192] ** Checking extended attributes file.
[12:47:52.0192] ** Checking volume bitmap.
[12:47:52.0192] ** Checking volume information.
[12:47:52.0192] ** Trimming unused blocks.
[12:47:52.0192] ** The volume System appears to be OK.
[12:47:52.0192] executing /sbin/mount_hfs
[12:47:52.0192] /dev/disk0s1s1 mounted on /mnt1
[12:47:52.0192] Trying to resize system partition to 1833959424 bytes aka 1749 MB
[12:47:52.0192] entering adjust_partition
[12:47:52.0192] partition: requiredSize=447744
[12:47:52.0192] no change in size
[12:47:52.0192] Successfully resized the system partition
[12:47:52.0192] entering maximize_data_partition
[12:47:52.0192] entering adjust_partition
[12:47:52.0192] partition: requiredSize=<<<<<IMEI>>>>>>6
[12:47:52.0192] maximizing data partition to 14020509695 bytes
[12:47:52.0192] entering adjust_partition
[12:47:52.0192] partition: requiredSize=3422976
[12:47:52.0192] no change in size
[12:47:52.0192] Successfully resized data partition to consume free blocks
[12:47:52.0192] The system partition now has a total HFS+ capacity of 1749 MB
[12:47:52.0192] entering ramrod_probe_media
[12:47:52.0192] device partitioning scheme is GPT
[12:47:52.0192] find_filesystem_partitions: storage=/dev/disk0s1 system=/dev/disk0s1s1 data=/dev/disk0s1s2
[12:47:52.0192] entering unmount_filesystems
[12:47:52.0192] entering ramrod_ticket_update
[12:47:52.0192] looking up root ticket hash
[12:47:52.0192] device tree ticket-hash: <CFData 0x15e3bf80 [0x369ad0]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}
[12:47:52.0192] ticket_hash: <<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>
[12:47:52.0192] received valid ticket (2729 bytes)
[12:47:52.0192] entering restore_images
[12:47:52.0192] Successfully marked device node /dev/rdisk0s1s1 as static data
[12:47:52.0192] executing /usr/sbin/asr -source asr://localhost:12345 -target /dev/disk0s1s1 -erase -noprompt --chunkchecksum --puppetstrings
[12:47:52.0192] void AppleUSBDeviceMux::handleConnectResult(struct BulkUSBMuxSession *, errno_t) new session to port 12345 failed: 61
[12:47:52.0192] void AppleUSBDeviceMux::handleConnectResult(struct BulkUSBMuxSession *, errno_t) new session to port 12345 failed: 61
[12:47:52.0192] ASR: asr: Unable to disable idle sleep - -536870199
[12:47:52.0192] ASR STATUS: start 241.1 multicast-client
[12:47:52.0192] ASR: Waiting for connection attempt from server
[12:47:52.0192] AppleUSBDeviceMux::handleConnectResult new session 0x930c8d10 established 12345<-lo0->49168 12345<-usb->22016
[12:47:52.0192] ASR STATUS: setup
[12:47:52.0192] ASR: Validating target...
[12:47:52.0192] ASR: done
[12:47:52.0192] ASR STATUS: metadata
[12:47:52.0192] ASR: Validating source...
[12:47:52.0192] ASR: done
[12:47:52.0192] ASR: Retrieving scan information...
[12:47:52.0192] ASR: done
[12:47:52.0192] ASR: Validating sizes...
[12:47:52.0192] ASR: done
[12:47:52.0192] ASR STATUS: restore
[12:47:52.0192] ASR RESTORE PROGRESS: 2%
[12:47:52.0192] ASR RESTORE PROGRESS: 4%
[12:47:52.0192] ASR RESTORE PROGRESS: 6%
[12:47:52.0192] ASR RESTORE PROGRESS: 8%
[12:47:52.0192] ASR RESTORE PROGRESS: 10%
[12:47:52.0192] ASR RESTORE PROGRESS: 12%
[12:47:52.0192] ASR RESTORE PROGRESS: 14%
[12:47:52.0192] ASR RESTORE PROGRESS: 16%
[12:47:52.0192] ASR RESTORE PROGRESS: 18%
[12:47:52.0192] ASR RESTORE PROGRESS: 20%
[12:47:52.0192] ASR RESTORE PROGRESS: 22%
[12:47:52.0192] ASR RESTORE PROGRESS: 24%
[12:47:52.0192] ASR RESTORE PROGRESS: 26%
[12:47:52.0192] ASR RESTORE PROGRESS: 28%
[12:47:52.0192] ASR RESTORE PROGRESS: 30%
[12:47:52.0192] ASR RESTORE PROGRESS: 32%
[12:47:52.0192] ASR RESTORE PROGRESS: 34%
[12:47:52.0192] ASR RESTORE PROGRESS: 36%
[12:47:52.0192] ASR RESTORE PROGRESS: 38%
[12:47:52.0192] ASR RESTORE PROGRESS: 40%
[12:47:52.0192] ASR RESTORE PROGRESS: 42%
[12:47:52.0192] ASR RESTORE PROGRESS: 44%
[12:47:52.0192] ASR RESTORE PROGRESS: 46%
[12:47:52.0192] ASR RESTORE PROGRESS: 48%
[12:47:52.0192] ASR RESTORE PROGRESS: 50%
[12:47:52.0192] ASR RESTORE PROGRESS: 52%
[12:47:52.0192] ASR RESTORE PROGRESS: 54%
[12:47:52.0192] ASR RESTORE PROGRESS: 56%
[12:47:52.0192] ASR RESTORE PROGRESS: 58%
[12:47:52.0192] ASR RESTORE PROGRESS: 60%
[12:47:52.0192] ASR RESTORE PROGRESS: 62%
[12:47:52.0192] ASR RESTORE PROGRESS: 64%
[12:47:52.0192] ASR RESTORE PROGRESS: 66%
[12:47:52.0192] ASR RESTORE PROGRESS: 68%
[12:47:52.0192] ASR RESTORE PROGRESS: 70%
[12:47:52.0192] ASR RESTORE PROGRESS: 72%
[12:47:52.0192] ASR RESTORE PROGRESS: 74%
[12:47:52.0192] ASR RESTORE PROGRESS: 76%
[12:47:52.0192] ASR RESTORE PROGRESS: 78%
[12:47:52.0192] ASR RESTORE PROGRESS: 80%
[12:47:52.0192] ASR RESTORE PROGRESS: 82%
[12:47:52.0192] ASR RESTORE PROGRESS: 84%
[12:47:52.0192] ASR RESTORE PROGRESS: 86%
[12:47:52.0192] ASR RESTORE PROGRESS: 88%
[12:47:52.0192] ASR RESTORE PROGRESS: 90%
[12:47:52.0192] ASR RESTORE PROGRESS: 92%
[12:47:52.0192] ASR RESTORE PROGRESS: 94%
[12:47:52.0192] ASR RESTORE PROGRESS: 96%
[12:47:52.0192] ASR RESTORE PROGRESS: 98%
[12:47:52.0192] AppleUSBDeviceMux::sessionUpcall socket is closed, session 0x930c8d10 (12345<-lo0->49168 12345<-usb->22016)
[12:47:52.0192] ASR RESTORE PROGRESS: 100%
[12:47:52.0192] ASR: Copied 1666908672 bytes in 51.54 seconds, 31586.74 KiB/s
[12:47:52.0192] ASR STATUS: verify
[12:47:52.0192] ASR VERIFY PROGRESS: 2%
[12:47:52.0192] ASR VERIFY PROGRESS: 4%
[12:47:52.0192] ASR VERIFY PROGRESS: 6%
[12:47:52.0192] ASR VERIFY PROGRESS: 8%
[12:47:52.0192] ASR VERIFY PROGRESS: 10%
[12:47:52.0192] ASR VERIFY PROGRESS: 12%
[12:47:52.0192] ASR VERIFY PROGRESS: 14%
[12:47:52.0192] ASR VERIFY PROGRESS: 16%
[12:47:52.0192] ASR VERIFY PROGRESS: 18%
[12:47:52.0192] ASR VERIFY PROGRESS: 20%
[12:47:52.0192] ASR VERIFY PROGRESS: 22%
[12:47:52.0192] ASR VERIFY PROGRESS: 24%
[12:47:52.0192] ASR VERIFY PROGRESS: 26%
[12:47:52.0192] ASR VERIFY PROGRESS: 28%
[12:47:52.0192] ASR VERIFY PROGRESS: 30%
[12:47:52.0192] ASR VERIFY PROGRESS: 32%
[12:47:52.0192] ASR VERIFY PROGRESS: 34%
[12:47:52.0192] ASR VERIFY PROGRESS: 36%
[12:47:52.0192] ASR VERIFY PROGRESS: 38%
[12:47:52.0192] ASR VERIFY PROGRESS: 40%
[12:47:52.0192] ASR VERIFY PROGRESS: 42%
[12:47:52.0192] ASR VERIFY PROGRESS: 44%
[12:47:52.0192] ASR VERIFY PROGRESS: 46%
[12:47:52.0192] ASR VERIFY PROGRESS: 48%
[12:47:52.0192] ASR VERIFY PROGRESS: 50%
[12:47:52.0192] ASR VERIFY PROGRESS: 52%
[12:47:52.0192] ASR VERIFY PROGRESS: 54%
[12:47:52.0192] ASR VERIFY PROGRESS: 56%
[12:47:52.0192] ASR VERIFY PROGRESS: 58%
[12:47:52.0192] ASR VERIFY PROGRESS: 60%
[12:47:52.0192] ASR VERIFY PROGRESS: 62%
[12:47:52.0192] ASR VERIFY PROGRESS: 64%
[12:47:52.0192] ASR VERIFY PROGRESS: 66%
[12:47:52.0192] ASR VERIFY PROGRESS: 68%
[12:47:52.0192] ASR VERIFY PROGRESS: 70%
[12:47:52.0192] ASR VERIFY PROGRESS: 72%
[12:47:52.0192] ASR VERIFY PROGRESS: 74%
[12:47:52.0192] ASR VERIFY PROGRESS: 76%
[12:47:52.0192] ASR VERIFY PROGRESS: 78%
[12:47:52.0192] ASR VERIFY PROGRESS: 80%
[12:47:52.0192] ASR VERIFY PROGRESS: 82%
[12:47:52.0192] ASR VERIFY PROGRESS: 84%
[12:47:52.0192] ASR VERIFY PROGRESS: 86%
[12:47:52.0192] ASR VERIFY PROGRESS: 88%
[12:47:52.0192] ASR VERIFY PROGRESS: 90%
[12:47:52.0192] ASR VERIFY PROGRESS: 92%
[12:47:52.0192] ASR VERIFY PROGRESS: 94%
[12:47:52.0192] ASR VERIFY PROGRESS: 96%
[12:47:52.0192] ASR VERIFY PROGRESS: 98%
[12:47:52.0192] ASR VERIFY PROGRESS: 100%
[12:47:52.0192] ASR: Verified SHA-1 checksum 1666908672 bytes in 8.86 seconds, 183636.22 KiB/s
[12:47:52.0192] ASR STATUS: finish
[12:47:52.0192] entering ramrod_probe_media
[12:47:52.0192] device partitioning scheme is GPT
[12:47:52.0192] find_filesystem_partitions: storage=/dev/disk0s1 system=/dev/disk0s1s1 data=/dev/disk0s1s2
[12:47:52.0192] entering mount_filesystems
[12:47:52.0192] executing /sbin/fsck_hfs
[12:47:52.0192] ** /dev/rdisk0s1s1
[12:47:52.0192] Executing fsck_hfs (version hfs-227).
[12:47:52.0192] ** Checking Journaled HFS Plus volume.
[12:47:52.0192] ** Detected a case-sensitive volume.
[12:47:52.0192] The volume name is InnsbruckTaos11B554a.N42OS
[12:47:52.0192] ** Checking extents overflow file.
[12:47:52.0192] ** Checking catalog file.
[12:47:52.0192] ** Checking multi-linked files.
[12:47:52.0192] ** Checking catalog hierarchy.
[12:47:52.0192] ** Checking extended attributes file.
[12:47:52.0192] ** Checking volume bitmap.
[12:47:52.0192] ** Checking volume information.
[12:47:52.0192] ** Trimming unused blocks.
[12:47:52.0192] ** The volume InnsbruckTaos11B554a.N42OS appears to be OK.
[12:47:52.0192] executing /sbin/mount_hfs
[12:47:52.0192] /dev/disk0s1s1 mounted on /mnt1
[12:47:52.0192] executing /sbin/fsck_hfs
[12:47:52.0192] ** /dev/rdisk0s1s2
[12:47:52.0192] Executing fsck_hfs (version hfs-227).
[12:47:52.0192] ** Checking Journaled HFS Plus volume.
[12:47:52.0192] ** Detected a case-sensitive volume.
[12:47:52.0192] The volume name is Data
[12:47:52.0192] ** Checking extents overflow file.
[12:47:52.0192] ** Checking catalog file.
[12:47:52.0192] ** Checking multi-linked files.
[12:47:52.0192] ** Checking catalog hierarchy.
[12:47:52.0192] ** Checking extended attributes file.
[12:47:52.0192] ** Checking volume bitmap.
[12:47:52.0192] ** Checking volume information.
[12:47:52.0192] ** Trimming unused blocks.
[12:47:52.0192] ** The volume Data appears to be OK.
[12:47:52.0192] executing /sbin/mount_hfs
[12:47:52.0192] /dev/disk0s1s2 mounted on /mnt2
[12:47:52.0192] entering install_kernel_cache
[12:47:52.0192] writing kernelcache to /mnt1/System/Library/Caches/com.apple.kernelcaches/kernelcache
[12:47:52.0192] entering install_secure_vault_daemon
[12:47:52.0192] entering get_hardware_platform
[12:47:52.0192] platform-name = s5l8950x
[12:47:52.0192] linking /mnt1/usr/sbin/securekeyvaultd to /mnt1/usr/sbin/securekeyvaultd.s5l8950x
[12:47:52.0192] no securekeyvaultd for s5l8950x
[12:47:52.0192] entering ramrod_ticket_write
[12:47:52.0192] writing ticket to /mnt1/System/Library/Caches/apticket.der
[12:47:52.0192] entering update_device_firmware
[12:47:52.0192] create_baseband_update_options: Got imeisv: 6
[12:47:52.0192] baseband updater options = <CFBasicHash 0x15e3d840 [0x369ad0]>{type = mutable dict, count = 3,
[12:47:52.0192] entries =>
[12:47:52.0192] 0 : <CFString 0x162238 [0x369ad0]>{contents = "IMEISwVersion"} = <CFNumber 0x15d45750 [0x369ad0]>{value = +6, type = kCFNumberSInt32Type}
[12:47:52.0192] 1 : <CFString 0x162298 [0x369ad0]>{contents = "autoSetupEnv"} = <CFBoolean 0x369e88 [0x369ad0]>{value = false}
[12:47:52.0192] 2 : <CFString 0x1622a8 [0x369ad0]>{contents = "disablePing"} = <CFBoolean 0x369e80 [0x369ad0]>{value = true}
[12:47:52.0192] }
[12:47:52.0192]
[12:47:52.0192] _baseband_update_requires_system_filesystem_once: querying baseband to determine if it requires system filesystem
[12:47:52.0192] _baseband_update_requires_system_filesystem_once: query returned <CFBasicHash 0x15e3c9c0 [0x369ad0]>{type = mutable dict, count = 3,
[12:47:52.0192] entries =>
[12:47:52.0192] 0 : <CFString 0x162008 [0x369ad0]>{contents = "requireSystemPartitionMount"} = <CFBoolean 0x369e80 [0x369ad0]>{value = true}
[12:47:52.0192] 1 : <CFString 0x162028 [0x369ad0]>{contents = "requireUserPartitionMount"} = <CFBoolean 0x369e88 [0x369ad0]>{value = false}
[12:47:52.0192] 2 : <CFString 0x162038 [0x369ad0]>{contents = "requireBasebandFSPartitionMount"} = <CFBoolean 0x369e88 [0x369ad0]>{value = false}
[12:47:52.0192] }
[12:47:52.0192]
[12:47:52.0192] entering update_iBoot
[12:47:52.0192] found 'AppleImage3NORAccess' object in IORegistry
[12:47:52.0192] entering update_iBoot_image3_NOR_access
[12:47:52.0192] write_image3_data: flashing illb data (length = 0x24a1a)
[12:47:52.0192] write_image3_data: flashing SCAB data (length = 0xaf0)
[12:47:52.0192] ticket updated
[12:47:52.0192] write_image3_data: flashing ibot data (length = 0x4518c)
[12:47:52.0192] write_image3_data: flashing chg1 data (length = 0x88cc)
[12:47:52.0192] write_image3_data: flashing bat0 data (length = 0xaa4c)
[12:47:52.0192] write_image3_data: flashing batF data (length = 0x1484c)
[12:47:52.0192] write_image3_data: flashing logo data (length = 0x1a8c)
[12:47:52.0192] write_image3_data: flashing recm data (length = 0xdd8c)
[12:47:52.0192] write_image3_data: flashing dtre data (length = 0x153cc)
[12:47:52.0192] write_image3_data: flashing chg0 data (length = 0x260c)
[12:47:52.0192] write_image3_data: flashing bat1 data (length = 0x80c)
[12:47:52.0192] write_image3_data: flashing glyP data (length = 0xf8c)
[12:47:52.0192] AppleImage3NORAccess::_getSuperBlock imageVersion: 3
[12:47:52.0192] AppleImage3NORAccess::_getSuperBlock imageVersion: 3
[12:47:52.0192] [nand_part_core:INF@2289] first 2 pages of boot blocks written with copies of partition table
[12:47:52.0192] entering update_gas_gauge
[12:47:52.0192] entering update_ir_mcu
[12:47:52.0192] looking for mcu nub...no entry from path!
[12:47:52.0192] TiSerialFlasher not supported on this platform. Exiting.
[12:47:52.0192] entering update_baseband
[12:47:52.0192] update_baseband: registering for progress notifications
[12:47:52.0192] create_baseband_update_options: Got imeisv: 6
[12:47:52.0192] baseband updater options = <CFBasicHash 0x15d48140 [0x369ad0]>{type = mutable dict, count = 6,
[12:47:52.0192] entries =>
[12:47:52.0192] 0 : <CFString 0x1621e8 [0x369ad0]>{contents = "SystemRoot"} = <CFString 0x15e3b990 [0x369ad0]>{contents = "/mnt1"}
[12:47:52.0192] 1 : <CFString 0x162238 [0x369ad0]>{contents = "IMEISwVersion"} = <CFNumber 0x15d45750 [0x369ad0]>{value = +6, type = kCFNumberSInt32Type}
[12:47:52.0192] 2 : <CFString 0x162298 [0x369ad0]>{contents = "autoSetupEnv"} = <CFBoolean 0x369e88 [0x369ad0]>{value = false}
[12:47:52.0192] 3 : <CFString 0x162178 [0x369ad0]>{contents = "forceUpdate"} = <CFBoolean 0x369e80 [0x369ad0]>{value = true}
[12:47:52.0192] 5 : <CFString 0x1622a8 [0x369ad0]>{contents = "disablePing"} = <CFBoolean 0x369e80 [0x369ad0]>{value = true}
[12:47:52.0192] 6 : <CFString 0x162198 [0x369ad0]>{contents = "DisallowFusiing"} = <CFBoolean 0x369e80 [0x369ad0]>{value = true}
[12:47:52.0192] }
[12:47:52.0192]
[12:47:52.0192] update_baseband: querying baseband info
[12:47:52.0192] bbupdater: BEGIN: Querying info at stage first
[12:47:52.0192] bbupdater: BEGIN: Preparing first stage
[12:47:52.0192] bbupdater: Requested boot mode: kBBUBootModeNone
[12:47:52.0192] bbupdater: Creating transport, attempts remaining 5...bbupdater: OK
[12:47:52.0192] bbupdater: Baseband VendorID [0x5C6] ProductID [0x9008]
[12:47:52.0192] bbupdater: END: Preparing first stage
[12:47:52.0192] bbupdater: Connecting to Loader...bbupdater: OK
[12:47:52.0192] bbupdater: Getting Version...bbupdater: OK
[12:47:52.0192] bbupdater: Loader version: PBL-DloadVER2.0
[12:47:52.0192] bbupdater: Fusing disallowed, will treat as fused
[12:47:52.0192] bbupdater: END: Querying info at stage first
[12:47:52.0192] update_baseband: query returned <CFBasicHash 0x15d4adb0 [0x369ad0]>{type = mutable dict, count = 6,
[12:47:52.0192] entries =>
[12:47:52.0192] 0 : <CFString 0x162318 [0x369ad0]>{contents = "CertHash"} = <CFData 0x15d4ade0 [0x369ad0]>{length = 32, capacity = 32, bytes = 0x<<<<Appears Hardware issue. See http://support.apple.com/kb/TS3694#hardware
Contact Apple Support Appointment at Genius Bar -
Trouble with restoring Ipod in disk mode
So i have a 30GB Ipod video that i am having trouble restoring.
I have reset it and it goes to the sad face with the exclamation mark. I have gotten it in diagnostic mode and it looks like everything scans okay. I then ran it in disk mode and it shows the white page that it needs to be restored. Then it flashes "okay to disconnect" for a few seconds and the "do not disconnect"
Its hooked up to my laptop and have used mutliple USB ports. It gets recognized under my devices and has the double chime noise that windows makes. I right click onto the ipod to troubleshoot but nothing gets detected. The problem is i only have about 1 minute while its it disk mode and it says "do not disconnect" before it restarts.
what can I do (if anything) to make it stay longer in disk mode. I have itunes open (which I have reinstalled multiple times) but it never pulls up ipod as the source or lets me sync it.
So if i bring it to the genius bar how much to they charge just to look at it. I wonder if you thinks non repairabe that i should just put that money towards a new one.After recharging it for at least 2 hours, do the iPod Disk Diagnostics, as posted earlier by tt2, it wont fix your problem but helps in troubleshooting.
There are 3rd Party iPod service clinic, that do free evaluation, just google for one in your Area.
Maybe you are looking for
-
I need to download an updated version of a file every few days to use. My secretary works on the file all the time. I thought i could use my old airport extreme and attach an external HD and set up a network to do just this. At work we alll use pc's
-
How do I publish for flash player 9? using macromedia mx 2004
-
Hi All, I am trying to configure OIM with Exchange 2003, for this I am using exchange connector MSFT_Exchange_91100 with OIM 9101. I have copied the jar files to required directory and also imported the xml and according to the documentation I need n
-
I always hated doing site upgrades when the original site was done by someone else. But sometimes I gotta bite the bullet, case in point as I'm so frustrated and now turn to the DW gods for help! The site is http://www.kanefilms.tv/ problem - if you
-
Music player doesn't show up in itunes window
I downloaded itunes and moved all my music to the itunes library and now I can't load music to my music player. I looked in Help and it said that my device should show up in the itunes window but I can't click on that window. Can someone help me?