Routing setup Time based on material length

Hi All,
I have a situation where i have to write an Object Dependency to change the setup time of an operation based on the length of the material selected by the customer.
For the first 5 inches, the Setup time should be 4Hrs, for each additional 5 inches the Setup time should be increased by 1Hr. there is no limit on the length they can select.
I have created a Reference Characteristics SETUP_TIME, and have a Characteristic called LENGTH. I could use some help with writing the dependency.
Thanks for the help.
Raj

Hello Raj,
Please review the link . You can create a procedure as defined in this link.
http://help.sap.com/saphelp_47x200/helpdata/EN/92/58c3a1417011d189ec0000e81ddfac/frameset.htm
Eg ,
$SELF.SETUP_TIME = MDATA $SELF.SETUP_TIME + 30 IF COLOR = 'FL'
OR $SELF.SETUP_TIME = $SELF.SETUP_TIME + 30 IF METALLICEFFECT = u2018Yesu2019
You should only usee MDATA if you reading the value from master data ,for a changed value you do not need to use MDATA.
You can also achieve this by usingVariant functions in a procedure. You can write a code to do a calculation based on the values you are sending. Assign this FM (OD) to the reference characteristic. You can find more information on this on the following link.
http://help.sap.com/saphelp_47x200/helpdata/EN/92/58c6eb417011d189ec0000e81ddfac/frameset.htm
Hope this helps
Thanks Amber

Similar Messages

VC - Dependency for routing setup time

Hi all,
During dependency editor programming, I had this difficulty with creating a procedure for summing up the setup time in the routing.
We have 3 components A,B,C as multiple selection in a characteristic with variable BOM quantities.
Based on the selection of these components, we have characteristics called QA,QB and QC to obtain the quantity of the respective components and pass it on to STPO-MENGE of the specific components.
We have another procedure which sums up the total of QA, QB and QC and multiplies this to the setup time in the routing for a particular operation.
The code for this dependency is:
$SELF.SETUP_TIME = MDATA $SELF.SETUP_TIME * (QA + QB + QC).
The issue we have here is the code calculates the setup time only if all the 3 characteristics QA,QB and QC is filled.
We want the QA,QB and QC characteristics to be displayed only if that particular component is selected. Can anybody suggest how to code the procedure to output a sum even if one of the characteristics is not SPECIFIED.

$SELF.SETUP_TIME = 0,
$SELF.SETUP_TIME = $SELF.SETUP_TIME + QA
   IF QA SPECIFIED,
$SELF.SETUP_TIME = $SELF.SETUP_TIME + QB
   IF QB SPECIFIED,
$SELF.SETUP_TIME = $SELF.SETUP_TIME + QC
   IF QC SPECIFIED.

WRT54GX4 - Difficulties Accessing the Router's Web-Based Setup Page

WRT54GX4 - Difficulties Accessing the Router's Web-Based Setup Page.
I have tried everything posted to the forums and the Knowledge Base for several weeks now with no luck. I can power push router and gain access to router's web-base interface but only for a few minutes than it quits loading part way through and or does not load at all. If I turn off the wireless side I can access the router at will with no problems. My warranty is almost over. I am at my wits end. I would like to get it replaced under warranty if I can. (^8
Solved!
Go to Solution.

Thank you for your recommendations peanuts. (^8
I bought the router back in December 10, 2006.
I updated the firmware to v1.00.20 back in June 2007. After I did a successful firmware upgrade I reset the router to factory default settings and then reconfigured it. It has worked Ok till a couple of months ago.
I have read everything I can find here on the support forum and in the Knowledge Base several times.
I have tried changing all the different settings to the different recommendations posted here and in Knowledge Base with no success. Each time I would do a long reset back to factory defaults, let it soak for a few hours and then make one change at a time and let it soak.
I have been monitoring 6 other wireless AP(s) around me (none mine) for a couple of months too. None of them are strong enough to connect to. My SSID is different from them. I have tried all the channels. My router is passworded and MAC'd.
It is looking like it is time to call support and try to get a replacement under warranty while it is still in affect.

Error in router's web-based setup page (WRT54G V5)

Hi,
My router’s web-based setup page is unable to load fully.
There seems to be an error with some document.setup.save file.
I have tried to reset my router but the router’s web-based setup page is still unable to load fully.
Please help.
Thanks.

Try Internet Explorer, it usually works.
JavaScript must be enabled.
Temporarily turn off your computer's software firewall, and see if that corrects your problem.
Hope this helps.

How is easy is to setup Time Capsule as a wifi router

How easy is it to setup Time Capsule as a wifi router?

The following would be the basic setup steps for the Time Capsule (TC):
Modem/Router Power ReCycling
o Power-off the Cable modem, TC, & computer(s); Wait at least 30 minutes.
o Power-on the Cable modem; Wait at least 15 minutes.
o Power-on the TC; Wait at least 5 minutes.
o Power-on the computer(s)
Either connect to the TC's wireless network or, temporarily, connect your computer directly (using an Ethernet cable) to one of the LAN ports of the TC, and then, using the AirPort Utility in Manual Mode, check these settings:
AirPort - Base Station
o Base Station Name: <whatever you wish or use the default>
o Base Station Password: (optional)
o Contact: (optional)
o Location: (optional)
o Set time automatically (optional)
o Time Zone: <select your time zone>
o Status Light: Always On (Default)
o Allow configuration over Ethernet WAN port (unchecked)
o Advertise configuration globally using Bonjour (unchecked)
AirPort - Wireless
o Wireless Mode: Create a wireless network
o Network Name: <whatever you wish or use the default>
o Allow this network to be extended (unchecked)
o Radio Mode: 802.11n (802.11b/g compatible)
o Channel: Automatic
o Wireless Security: None
AirPort - Wireless - Wireless Options
o Region: <select your region>
o Multicast Rate: 2 Mbps
o Transmit Power: 100%
o Create a closed network (unchecked)
o Use interference robustness (unchecked)
Internet - Internet Connection
o Connect Using: Ethernet
o Configure IPv4: Using DHCP
o IP Address: <provided by your ISP>
o Subnet Mask: <provided by your ISP>
o Router Address: <provided by your ISP>
o DNS Server(s): <provided by your ISP>
o Domain Name: <provided by your ISP>
o DHCP Client ID: (optional)
o Ethernet WAN Port: Automatic (Default)
o Connection Sharing: Share a public IP address
Internet - DHCP
o DHCP Range: 10.0 1.x
o DHCP Beginning Address: 10.0.1.2
o DHCP Ending Address: 10.0.1.200
o DHCP Lease: 4 hours
o DHCP Message: (optional)
o LDAP Server: (optional)
o DHCP Reservations: (optional)
Internet - NAT
o Enable default host at: (leave blank)
o Enable NAT Port Mapping Protocol (checked)
Once you have verified Internet access, I strongly suggest that you use wireless encryption (WPA or WPA2) to secure your network.

HT1515 do i need to buy an apple time capsule to bridge my airport express or is it okay for me to just use my wi-fi router setup at home?

do i need to buy an apple time capsule to bridge my airport express or is it okay for me to just use my wi-fi router setup at home?

Sorry, I am confused by your question.
What devices do you now have on your network?
What are you trying to accomplish?

ISP Router/Modem Time Capsule - Optimal Setup

I've read many different threads on this issue but none have really address my question fully, so posting this in the hopes of getting some feedback.
I currently have an ISP that supplies a DSL Modem/Router that serves a dual purpose, provide me with internet and TV service. In Canada it's called Bell Fibe TV. Currently, I have the ISP Modem Wifi OFF, wired it to my Time Capsule and use it to provide Wifi throughout the house.
My question is related to all my other devices and whether they should be connected to the Time Capsule or the ISP Router. Time Capsule and Router are both located in the basement. I have my house hard wired with ethernet to the basement with 3 main outlets, one in the basement for my iMac computer/office, one on the main floor, and one on the top floor.
I have two 3 Apple TV's, one in the basement, one on the main floor and one on the top floor. I use a 5-port ethernet switch on the main floor as I have a variety of different devices there ie: Apple TV, TV Receiver Box, Sonos Player etc. I also have an Airport Express that is wirelessly extending my Wifi.
What is the optimal setup in this situation? I have my Time Capsule on DHCP with router mode OFF (Bridged). Should I be connecting the hard-wired ethernet cables that go throughout the house to the ISP Router/Modem or to the Time Capsule? Does it matter? In recent weeks, I've noticed some odd issues where my Apple TV will lose its network settings and not find the network.
Also, I noticed in BRIDGE mode, there's no way to setup a Guest account on Wifi.
Looking for any suggestions/help on this.
Thanks

My question is related to all my other devices and whether they should be connected to the Time Capsule or the ISP Router.
If the Time Capsule is configured correctly, it makes no difference whether devices connect to the Time Capsule or the ISP modem/router, since both the modem/router and Time Capsule are on the same network.
I have my Time Capsule on DHCP with router mode OFF (Bridged)
That is the correct setting for your situation.
Should I be connecting the hard-wired ethernet cables that go throughout the house to the ISP Router/Modem or to the Time Capsule?
See answer above.
The best practice, wiring wise, would be to connect an Ethernet cable from one of the LAN <--> ports on the modem/router to an Ethernet switch. Then connect the Time Capsule and all other Ethernet connections to the switch.
Performance will not be any better this way, but the network layout and troubleshooting are easier in this type of setup. If you do not want to add a switch, then connect to the most convenient port on either the modem/router or Time Capsule.
Also, I noticed in BRIDGE mode, there's no way to setup a Guest account on Wifi.
That is correct. The Guest Network feature will only work correctly if the Time Capsule is the main router for a network....not a bridge to the network.

Can't Access Router's Web-Based Setup Page

I have tried this: http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=3676
Entering in the default IP and my actual IP address does not work, I'm trying to find out what my security key is.
Solved!
Go to Solution.

When you Hardwired your computer to the Router, on your computer click on Start - Run - CMD and click ok, now in the Command Prompt window type "ipconfig" and hit enter.. Note down the Default Gateway IP address.
Open IE on your Computer and in the address bar type http://default gateway ip and hit enter,when prompted for the Username and Password, Leave the Username blank and type "admin" as a password and click Ok. (If you have changed the Router password, then you need to use that password to login to the Setup page of your Router).
Once you login to the Router setup page, click on the Wireless tab and then click on the sub tab "Wireless Security" and in the window you will find out your security key.

Delivery Date in SO not calculated with Route Transit Time

Hello Experts,
We are not able to calculate the delivery date in Sales Orders based on the Route transit time.We are using the Transportation group from Material master , Shipping condition from sold to Party , and Receiving issuing plants and zones .
One thing I notices is if we don't use the Transportation group in the material master , then the delivery date calculated based on transit time.Not sure not why its not working with using Trans group in Mat master
Please advise.
Thanks in advance

Hi,
Kindly do not post same questions twice
HI,
For delivery scheduling enter time
IMG >> SD >> Basic functions >> delivery scheduling and transportation >> maintain duration
Maintain here route, pick/pack & loading time
For in house production maintain time in material master in MRP view
Then now system will take in account what is production time + pick/pack + load time and then will schedule
Kapil

Time based mode runs 4 hours before time set

time based modes are running 4 hours early...
The mode was set for 6:00 pm, ran at 2:00 pm.
changed it to 8:00 pm it then ran at 4:00 pm
when creating the mode it said that EST after the begin time, so it knows the correct time zone that I am in
Bill T

Paul,
Can you elaborate on where you applied the configuration. I have a scenario where Rightfax sends the call to CUCM via an H323 trunk, then CUCM sends the call to the PSTN Gateway and then out to the PSTN. I am experiencing the same issue where the call disconnects before the destination fax answers if it is set to ring 3 or 4 times before answering.
I'm not sure that I understand what you mean by splitting the incoming and outgoing dialpeer. I have the following dialpeer to match and route my outbound number to the PSTN.
dial-peer voice 92 pots
translation-profile incoming PREFIX-9
translation-profile outgoing CALLERID
destination-pattern 91[2-9]..[2-9]......
progress_ind setup enable 3
progress_ind progress enable 8
port 0/0/0:23
forward-digits 11
I appreciate any help you can provide.

I am trying to setup time limits in airport 5.6

I am trying to setup time limits for internet usage in airport 5.6—
but i don't get a timed access control "option. Tried on both imac and macbook pro.

What are you setting it up as.. join wireless network .. the very worst setup, it will disappear.. reboot the whole network in order modem. router TC.. clients and it will likely reappear.
Tell us what network setup you are using..
If you setup with cable to a computer completely isolated from the network with TC also isolated.. finish the setup of everything you want. .before update.. then plug it into the network. .then restart everything in correct order.. it will work most of the time.

Can't connect to router setup page

Hi,
I have a WRT54G wireless router, version 2.1. It's been working fine for the last 3 years and suddenly the WLAN light is out and there's no communication between router & computer. I've tried resetting it (via reset button, and unplugging power) a million times with no results. A techie thought maybe I needed a firmware upgrade -- which I've downloaded, but now I still have to access the setup page to install it, which seems to be impossible. The 192.168.1.1 page won't come up at all. (And when I went into the command prompt, it said my Default Gateway was 207.237.223.1 -- which, of course, I've tried, but that won't come up either.) I've turned off firewalls and antivirus programs, thinking they might be the problem -- still nothing. Any suggestions/advice would be MUCH appreciated! Thanks in advance!
TrevorNYC

You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.

QC Activity based on Material Production Version

Hi,
Normally, we perform QC activity based on Material Code, i.e. in Material Master we maintain inspection type in QM View for material which needs QC activation during Good Receipt from Production
Is it possible to perform QC Activity based on Production Version of a material i.e.
For Example
Product A having 2 Production Versions
IF Product A with Production Version 1 then No QC required during goods receipt from production
IF Product A with Production Version 2 then QC required during goods receipt from production
So please tell me what feasible solution possible from your side
With Regards,
Kunal Sheth

Dear Sap User,
Production version is nothing just a combination of Master recipe/Routing and BOM used for particular production or process.
If you are having so many production version then you have to choose which you want to choose but if you are having a single production version then it will be chosen automatically.
Do it once and revert in case of any query.
Rgrds,
Dheeraj Rawal
Edited by: Dheeraj89 on Feb 9, 2012 6:13 AM

Problem in Time Based Publishing Content

Hi every1,
Im working with Time based publishing.
Using xml form builder i created 3 contents means 3 xmls.
Then i created one iView for reading the contents (KM Navigation iView) and i setup the properties like
layout set, layout set mode, root folder of contents.
After creation of iView i checked in the preview all 3 contents visible in my iView.
Now i want to show time based content in that iView.
Contents displayed as per time based
for that i enabled time based publishing and life time of particular content(xml)by using the given way
Time dependant publishing in Km. I clicked on the right hand side of the name of my folder-> go to details -> Settings -> Lifetime. there you have to enable the time dependant publishing. Then i opened the folder and click on the rt hand side of the document-> properties -> lifetime, here give the time span of the document.
After life time setup , again i seen in the iView for reading the contents (previous created) in the preview
again all 3 contents displayed including life time expired content also.
Please give me solution for this, or any more configurations required.
Note :
I required to display the contents in between time applicable only ( from time and until time).
Thanks in advaince
Vasu

I have waited more than 3 hours for settings to apply.
But i couldn't find any changes.
any other solution?
Thanks
Vasu

E4200 - Okay router, setup issues

I chose this router over the Netgear N750 because of previous bad experience with their customer support and over the Asus RT-N56U b/c of a compatibility issue with a specific application.
The Cisco Connect Software is very poor software. No OSX Lion support so I could not use my Mac for setup and it could not even detect the router on a wired connection on a Windows 7 PC through a simple Dell unmanaged switch. Even the router setup software built into Windows had no problem with that. I had to rely on manual setup which was straightforward.
Range was mostly adequate for me with both 2.4 and 5 Ghz over 5,000 sq. ft. of indoor space with no direct line of sight, through many walls, multiple floors, and the outside patio also, although with a few connected devices I found the 5 Ghz band somewhat unreliable at times. Wired gigabit performance was good enough for my purposes.
Overall a decent router, not bad, not great.

It seems like you are using an outdated version of Cisco Connect Software… There is a new release of the Cisco Connect Software that supports Mac OS X (10.7 "Lion")… So you need to download the latest Cisco Connect from the Cisco Website (homesupport.cisco.com) or you can use this link: http://homesupport.cisco.com/en-us/support/routers/E4200 ... After downloading you need to set the router to factory defaults, power cycle the whole network and then run the Cisco Connect that you downloaded…
For more information about setting up E4200 router with Cisco Connect. Please refer to the link below.
http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=22732&userrole=Links...

Routing setup Time based on material length

Similar Messages

Maybe you are looking for