RS482M4 TV-OUT problems / Better BIOS?

RS482M4-ILD is the board i have
Using on board Video /W the D-SUB connection.
What i have tried is the CD-Driver, MSI's, Latest Driver and now am using ATI's IPG 5.13 Driver.
However i can not use both TV-OUT and VGA at the same time, anyone have any idea for me?
Also does anyone know of a better BIOS for this board?
Beta or modified it doesnt matter, memory settings are VERY VERY poor, CAS only
And Voltage HTT options at all.
I am using my old RAM on this board, and would like to run it properly, its PC4000 / DDR 500
SO the goal is to run the RAM at a 1:1 ratio.
Dont plan on overclocking so i would be lowering the multiplier (currently the only option i have) to keep the CPU at around stock speed
I will also probly lower the Vcore on this CPU to keep heat low as its in a SFF case.
CPU is a 3200+ that did 2.7GHz in its day

This is a cross-post from another thread discussing the same problem.
It is not documented anywhere in the MSI manual, but the problem is the VGA and TV Out video ports share the same RAMDAC (video channel) and cannot both be active at the same time. Or if they can (I have a discrete ATI card that allows this), it is not yet supported in the driver.
Thus, the only way you can get TV Out with the VGA port in use is to use *only* TV Out. You can do this in Catalyst Control Center by dragging the image of the TV or HDTV in the "Displays connected but not in use" list to the "Main Monitor" (CRT) above the list and selecting the only available option, "Swap". This will enable TV Out and disable your CRT. Do the reverse to re-enable the CRT & disable the TV Out. You can I'm sure assign these two configurations to hotkeys (I usually use Ctrl-Alt-F1 for normal, & Ctrl-Alt-F2 for TV Out).
I assume with a DVI monitor plugged in that both the digital flat panel and TV Out could be active at the same time, but I haven't tested this. I will get a chance to in the coming week though.
If you have an LCD flat panel with both VGA and DVI plugs, try using a DVI cable instead to enable dual displays. If you don't have one already order from ComputerCableStore.com, which I have found the cheapest anywhere (DVI cables start at under $14 before shipping; the local big box stores sell them for $40-$130(!) in comparison).
Otherwise, you may have to buy a new DVI-capable LCD monitor to enable this functionality. If you do pay attention to what comes in the box - I just bought a Samsung 19" display for around $300 and it didn't include a DVI cable in the box. It may or may not make sense to order the cable separately depending on the price difference for models that do or do not include a cable. If you are not sure if a cable is included with a particular model, see if it is listed on NewEgg.com - their product pages are the best on the web and usually include pictures of the contents of boxes, as well as links directly to the manufacturer's product page which often list detailed specs.

Similar Messages

MSI Z87-G45 Latest beta bios problem?

So i have updated to the latest beta bios but the core jumps to 5600mhz from 4500mhz.
Everything is set like it's alway's set.(4500 core @ 1.285v 4200 uncore/ring @ 1.19v, memory on xmp profile and the inputvoltage is 1.880v)
This only happens when using firefox from what i've seen, but i haven't done testing yet so it could happen with more programs.
Firefox becomes laggy when this happens and doesn't want to load anything unless you wait 25 seconds and then it still not load's the site complete.
IE 11 doesn't do this by the way.
My setup:
MSI Z87-G45 Gaming
Intel I7 4770K
G.Skill Ripjaws X 16gb
Sapphire R9 290
Cooler Master Silent Pro 1000W
Edit: The clock's are just showing up that high in task manager, in XTU they stay @ 4.5.
But i still don't know why firefox is acting up with this bios.

Close this topic as i have found the problem.
It was a usb 2.0 stick in usb 3.0 port that was saving the cache for firefox.
But the stick was working very slowly in that port hence the slowdown.
Sorry for the thread.

KT4 - Errors, Beta BIOS ???

I am having the same problem as everyone else with the CRC and Corrupt file errors when using FSB 133.
Does the Beta BIOS work? Has anyone tried it and had any problems or improvement?
Razdyn ?(

If you know how to flash the BIOS, know what is a beta BIOS about (ie not supported, not warranted if you flashed wrong, only for testing and experiment purpose...), you may try out.

K8N Neo2 Plat (M7025) Beta Bios

Hi all,
Noticed that Neo2 has some beta bios out, like 133 134 and 135. Has anybody tried these things? Anything good in the new bios? Any problems? Grateful if someone knows about it could share his knowledge/experience.

Yeah, I don't care what those guys say over on PC Perspective; for my system, BIOS 1.35b is golden.
Rock solid stability: http://img48.exs.cx/my.php?loc=img48&image=Prime95-30h00m.jpg. (For those too lazy to click the link, that's a screenshot of my 30 hour Prime95 run.)
I also ran memtest for a full 24 hours as well: 46 std test passes, 2 extended test passes. (I took a picture, but I'm too lazy to upload it.)
For v.1.23b and v.1.2 (Official), I could never run Prime95 for more than 9.5 hours.
I'm downloading 3DMark05 right now, but since everyone on the planet must be downloading it, it's going at a pathetic 7.9 KB/s rate! (It won't be done for another 10 hours.) So I haven't "torture tested" my video card, but I have been playing UT2K4, Doom 3, and Sims 2 for days on end hours at a time with no problems.
System:
AMD 64 FX-53
MSI K8N Neo2
TwinXCMS3200XLPro (2x512 MB) (2-2-10-2-1T @DDR400, 2.75 V)
eVGA GeForce 6800 Ultra
EDIT: Oh, I set the CPU voltage to 1.55 V. I only did this to get back a reading of 1.50 V.

K9N Platinum Beta Bios?

Can anyone tell me or show me if there is a new beta bios out for the K9N Platinum?
Right now I'm using beta 1.45 and it works great! Except...I just want something that will fix the stupid cpu temp reading!!!
Lemme know if you find anything.
thanks!

Quote from: natasha on 09-January-12, 03:00:18
What cpus does this bios support? Just curious if it will do a phenom 9750.
Please start your own new topic instead of bringing up one that's been dead for 5 years.
>> Please read and comply with the Forum Rules <<
>> Posting Guide <<
Edit: No the K9N Platinum does not support AM2+ CPUs of any kind with any BIOS.

ITunes will not allow me to drag files onto my desktop or a USB drive. The files still come up in finder and I can drag from there but I need entire playlists transferred. It started this when Yosemite went public and I updated out of BETA.

Songs and Playlists cannot be dragged from the itunes app onto desktop or usb drives.
Files can be dragged from Finder but only one at a time.
The issue started when I updated Yosemite out of BETA.
I am running:
OS X Yosemite 10.10
2013 Macbook Pro
iTunes 12.0.1

Hey! I had the same problem you did just today when I was trying to get my second iPhone to sync. What you need to do with music or anything extra that you doing you have to creat a second playlist or picture or anything that you would like to use, so that you can add to the second device that you are going to be using. I am not sure if that will help but it helped me out a lot!! Good luck!

TV OUT Problem this is how I solved.

Well, first of all I cannot guarantee if this will work for all people with tv out problems. TV with PC I think will always be a BIG headache .
How I did fix my TV OUT problem. Since I live here in Brazil, people have a problem with the system that is Pal-m. But this is easy to set up, since you just have the screen working on your TV.
The first thing that I did is to remove completely the most recent NVDIA drive (not the one made for MSI) that is 30.82. I also removed the WDM driver. Since Im using XP I didnt have to reboot 30 times just 20, , yes 20 reboot times to see if everything was all right, it took me about 1,5 hour of work.
The second thing was that I started to install the driver that came with my MSI Card (Geforce4 MX-460 TV OUT). The version was 27.50. The TV out problem was gone. I got a really nice image from the screen.
Than It came the must boring part. ;( I tested all nvidia drives from 27.50 to 30.82. Look the results I got concerning just the nview situation(dual monitors):
Nvidia 28.32. work with nview.
nvidia win-xp-2k-2835 work with nview.
nvidia win-xp-2k-2880 doesnt work with nview.
nvidia win-xp-2k-2890 doesnt work with nview.
nvidia win-xp-2k-2911 doesnt work with nview. Not all parts from the driver was updated, someone belongs to 28.90.
nvidia win-xp-2k-2920 doesnt work with nview.
nvidia win-xp-2k-2942 doesnt work with nview.
nvidia win-xp-2k-2960 doesnt work with nview.
nvidia win-xp-2k-2980 doesnt work with nview.
nvidia Win2k-xp-29.90 doesnt work with nview.
nvidia W2K_XP_V29.90 doesnt work with nview
nvidia Win2k-xp-3020 doesnt work with nview
nvidia Win2k-xp-3030 doesnt work with nview.
nvidia Win2k-xp-3082 doesnt work with nview.
I got all this drivers from a really nice site: 3dchipset .
Of course most of these are beta drivers and due to my limitation knowledge, I dont know why the nview display stopped to work at version 28.32.
And the last. The driver 28.90 driver did a really fatal crash on my PC when I was using my web camera and the nview together. It just shut down my PC, at once. X(
That all folks

Yes, that's how iMessage should work. Try this. Sign out of Messages on both devices. Sign back in on your phone and wait until it activates. Go to Settings>Messages>Send & Receive. Make sure Start New Conversations From is set to our mobile number. Then sign in on your iPad using the same Apple ID as you use on your phone. Once it activates, verify the settings. I've got iMessage syncing across my iPhone, iPad and MBA. Every once in a while, there's a glitch but rarely.
Best of luck.

Unstable with last beta bios on z77 Mpower

hi all,
I've just install the last beta bios, and i can't boot now with my last setting. pc was stable with it, now i've got problem.
I run now with automatic OC but can run my ram @ 2600MHZ.
In manual oc configuration, i can't run the base clock can't runing @ 102, pc reboot and reboot permanently, bios freeze....well very bad beta bios, so what i can do?
Thanks

Or the beta previous to that one.
>>Use the MSI HQ Forum USB flasher<<
>>Beta BIOSes<<
If the primary is unstable, try this method:
https://forum-en.msi.com/index.php?topic=160450.0

600 and 600e modem problem, and BIOS update

I hope I can find the answers to my 600 and 600e problems here. I've looked over the whole community and can't find the answer to my problems.
BIOS Problem: For some reason I can't update the bios on either machine. I am upgrading from 98 to 2000. I believe I need spsdib54 as a BIOS update. I find IBM laptops rather difficult to update. I have worked on a few computers in my day, but never IBM until now, and the learning curve is hell. I have a floppy drive but can't get the laptop to allow the spsdib54 file to open. I get a remove media message and then hit any key to continue. I'm lost here.and theIBM instructions are no help
MODEM Problem. I am trying to use AOL dialup. I install 2000, and can test my modem on both machines. I install AOL with no problems. Both laptops will dial out and get the correct Phone numbers. When I let AOL use smart connect and try to proceed, I loose all modem activity, and can't get it back even with the Modem upgrade which I have done. ....help

Thomasrwahl wrote:
I hope I can find the answers to my 600 and 600e problems here. I've looked over the whole community and can't find the answer to my problems.
BIOS Problem: For some reason I can't update the bios on either machine. I am upgrading from 98 to 2000. I believe I need spsdib54 as a BIOS update. I find IBM laptops rather difficult to update. I have worked on a few computers in my day, but never IBM until now, and the learning curve is hell. I have a floppy drive but can't get the laptop to allow the spsdib54 file to open. I get a remove media message and then hit any key to continue. I'm lost here.and theIBM instructions are no help
I. Create a System Program Service Diskette:
Download spsdib54.exe (TP 600E: spsdih47.exe or spsdin36.exe - find out here) to your desktop.
Insert a high density floppy disk into the diskette drive.
Double-click the downloaded exe and follow the instructions on the screen.
II. Follow the "Installation Instructions" in spsdib54.txt to update the BIOS:
Installation Instructions
Notes: - You need an AC adapter and a charged battery pack to update
              the system program.
          - If your computer is attached to any kinds of Docking station
             or port replicator, turn off the computer and detach it
            before proceeding.
            - Make sure the SPSD diskette is write protected.
1. Print these instructions or display on another computer.
2. Firmly connect the AC adapter to the computer.
3. Insert the System Program Service Diskette into the diskette drive
    and turn on the computer.
4. Select Read this first from the menu and carefully read the
    information that appears.
5. Press the Esc key to return to the menu.
6. Select Update system program and follow the instruction on
    the screen.
    Warning: Do not turn off or suspend the computer until the update
                   has been completed. IF YOU TURN OFF OR SUSPEND THE
                  COMPUTER WHILE THE UPDATE IS STILL IN PROGRESS, THE
                  SYSTEM BOARD MAY HAVE TO BE REPLACED.
After the update has been completed, do the following to make the
changes effective.
7. Make sure the System Program Service Diskette is removed from
     the diskette drive, then turn off the computer.
8. Press and hold the F1 key, then turn on the computer. Hold the F1
     key until the Easy-Setup menu appears.
9. If a password prompt appears, type the correct password.
10. Select Config, then select Initialize.
11. Select OK to initialize the system.
Run the diagnostics to make sure that the computer runs with no
errors:
12. Turn off the computer, press and hold the F1 key, then turn on
     the computer. Hold the F1 key until the Easy-Setup menu appears.
13. Select Test, then select Start to run all the basic tests.
    Various test patterns will appear on the screen.
     An OK will appear for each device that passes the test.
14. Verify that OK appears for all of the devices tested.
15. Press the Esc key to exit Test and turn off the computer.

Where can I download a beta bios?

I have searched the web for hours and I cant seem to find a Beta bios for my 865G-PLS MB, I am looking for a bios that has fixed the X800 videocard problem and one that allows the CPU core voltage to be adjusted.
Thanks for the help.

Thanks Del and Danny, the only issue I have atm is the fact I bought a prescott =P, really though I installed an X800 Pro and I have problems with lock ups due to the X800 bios isue and I really dont want to use the 3.7 bios because I am unable to change the core voltage, thus I cant overclock and hit 3.7 Ghz anymore.
I am going to go ahead and use the 3.7 and see if it clears up the issue I am having and go from there, but going from 3.7Ghz back down to 3.4Ghz is gong to cause me great pain hehe.

MSI 880GMA-35 FX [MS-7641 rev 2.1] - BETA BIOS Request

Hi, there beta bios for this motherboard?

I asked in this section to check for new updates in development. Since I bought this card in bundle with a processor AMD PHENOM X II, I'm having a series of problems:
- Lack of recognition of the AMD Phenom II x 960T BE (it was declared like supported but i must upgrade bios and clear cmos twice to recognize it successfully)
- Incompatibility with Samsung Hard Disk 502HJ (i found a incompatibility between SB850 and this HDD that i fix with a firmware update)
- problem with the Crucial M4 SSD (installation in AHCI mode only)
- Not being able to individually set the mode of access to individual devices (ide or ahci)
and look forward to some improvement:
- Unlock function on the core (which is not handled of software UNLOCK CAP as promised on the website of the motherboard where says "This new MSI software tool allows users to unlock CPU cores from Windows with just a few simple clicks, no need to enter the BIOS." )
I hope Msi coul emprove some function in next release and provide the software MSI's UNLOCKCAP with this motherboard.
(it's the same chip 880)

P7N Beta bios 1.1B4..closing in on 500mhz FSB

Played around with the beta bios tonight..using a 6X multiplier..got 487mhz fsb out of it..I'm pretty sure 500+ is out there, but my ram is dragging me down..lol. Had .125v cpu, 1.4v NB and 2.0 SB all others auto to get to this point.
http://valid.x86-secret.com/show_oc.php?id=325249
Paul

Proxyma,
I have no idea of the NB temp? MSI uses a temp sensor "near the middle of the motherboard". System temp is typically 28-30C idle and 32-33C under load. I dont think my NB ever gets too hot because it's watercooled along with the CPU. The highest temp I've ever seen logged for the CPU was around 48C (during a Crysis benchmark run at max settings).
Paul

K7D Master beta bios

I have been looking around the MSI site for over an hour for a beta bios I was told about. I am looking for the K7D Master (6501) beta bios. I was told it was 2.10 or something close to that. Someone please tell me where MSI hides this stuff at before I lose my mind.

Chris: Thanks for the link to that bios, I didnt know they had a 2.x out. It is dated the same as that 1.9 which I installed. My system has two of the mobile 2500+ chips. The 1.9 bios does not support the mobile and I use that CrystalCPU multiplier to change the speed from 800 to 2000. It is flakey and at the exact time it is supposed to switch to 2000 occassionally (1 out of 10 or so) I see a blue screen. I was wondering if that 2.x bios has support for mobile amd chips. All I see is that support was added for sempron. Not sure that that does on a dual processor board. So sempron can work on dualies?

If MSI starts a beta bios, then why do they leave it unfinished?

Dear Moderators of this BIOS Section,
Can you just tell me please why MSI simply leave a beta bios unfinished? Like K8N Neo2 Platinum bios 1D2????
I just wondered that point... When I asked them if they would finalize that version, they simply give the usual answer you give, 'don't flash/update a bios, if it works fine...' OK, I know this point very well but what they do is ignore the question anyway....
Kind regards you all
Zeki

Quote from: Zeki on 11-January-07, 08:18:42
Dear Syar2003,
I know you are an expert on modifying bioses. Can't you please modify this beta bios and as you said, finalise it as a final release and give it out as a 'syar2003' modified bios?
Thanks very much.
Zeki
K8N Neo 2 Platinum 1D2 Mod ---> https://forum-en.msi.com/index.php?topic=103653.msg761110#msg761110
Use it at Own Risk. Make and Ensure PC is stable before proceed. do not forgot to clear CMOS via regular way after BIOS update is complete successfully.(remove power cord from the PSU before proceed with Clear CMOS). you can PM to the_cultie and Daver(which i know its used for sure) for experience and feeback before proceed.

Problem with BIOS upgrade

I have a UK model laptop, a Satellite C855-1HM. (The website for Tosh UK has redirected me here for support.)
This evening I was prompted by the Tosh software to upgrade BIOS from 6.60 to 6.70 using the InsydeFlash download and installer. I have used this function several times before with no problem.
This time, however, when the system restarted, the wireless adapter was not working, and looking in Device Manager I found that there was a resource conflict, though I could not see what it was conflicting with, it simply told me that the resources wanted by the wireless weren't available. Luckily I have a 5 metre ethernet cable handy...
I managed to find the 6.60 download on Tosh website, but of course when I tried to run it it refused, saying 'The Version of ROM file is not newer than that of BIOS'. I looked for a way round this, and tried tweaking the platform.ini, as suggested by various websites, but with no success. I tried also reinstalling the 6.70 BIOS but it also refused to work, saying it is the same as the installed BIOS.
Eventually I thought of restarting the laptop. I was pleased to find that the wireless adapter now works, but now there is no sound - '"No audio output device is installed", it tells me, although I can't see anything wrong in Device Manager, there must be something missing.
So basically I still need to find a way to reinstall the older BIOS. I have managed to unzip the files and look at them. One website I referred to suggested that there would be a date in one of the files, but I haven't located that, even with a hex editor. Is it in the F8660.FD file, and if so, in what format?
I would be very glad of any help - a.s.a.p, please. Thanks in advance.
Solved!
Go to Solution.

egarobar wrote:
Hi there, the Tosh comes with a program called Service Station, which I turned on when I got the laptop (9 months ago). About 4 times this year it has prompted me to upgrade the BIOS. I assumed it was important, as it seemed to be saying there were software vulnerabilities (can a BIOS get a virus?)... so I did as they said!
I thought Toshiba knew what they were doing - and the software they sent out would RELIABLE - I was wrong.
I am still trying to return to the 6.60 version, but no luck - I need some practical help, please.
I do not know of a way to revert back to an older version bios (on a laptop). however, if it just a matter of audio, try ininstalling the audio driver and reinstalling. You have the latest bios installed and your computer is running ok, except for this audio driver issue. consider yourself luck as Dokie pointed out, updating a bios is serious and if interupted for whatever reason, it can render your computer permanantly inoperable. Unless you are experiencing problems, pass on the bios update. you can't get a virus from having an older version bios.
L305-S5955, T9300 Intel Core 2 Duo, 4GB RAM, 60GB SSD, Win 7 Ultimate 64-bit

RS482M4 TV-OUT problems / Better BIOS?

Similar Messages

Maybe you are looking for