Scaned Paper Quality Problem

Dear Sirs,
I could not get high quality paper with low sizes. For example, when i choose dpi 300 with black colour,the size is 3,6 MB for 9 pages. When i choose 200 dpi, at that time we can not read the letter clearly and size is aprx 1mb for 9 pages. 
The question is how can set up the printer for ideal size and quality exclude DPI Settings.
Note: I was using Samsung and Brother multifunction and i was scanning 300dpi black and white as 516kb for 9 pages.
Thank you,
ibrahim olcal

Hello there! Welcome to the forums @ib0 
Could you please let me know which HP product you have? I will do my best to help you with it from there!
How Do I Find My Model Number?
Thank you
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Similar Messages

  • Officejet K550 Pro: Paper Feed Problems

    About a year or two ago, we purchased a K550 unit for our office, and 3 subsequent units for employees' personal use.  At first, everything went great - it was the best inkjet printer I or my staff had ever owned!  After a month of great service, my staff and I recommended this product to customers demanding a printer with low cost of ownership and fast, high-quality printing.  However, after about 3 months of service, all of our units began developing paper feed problems in about the order they were purchased, depending on their usage (the older units first, unless they were used more than other units).
    It started with an occasional failure to pickup a new sheet during a print job, slowly progressed to having to hand-feed the printer to get it started on a job and supervising the printer throughout the job to clear the occasional feeding problems during the job, and erupted into a continuous hand-feeding of every sheet of every job through all of these printers, all the time.  We immediately replaced, at our cost, all of the 15 customer units, 3 employee units and 1 internal unit that were purchased by us or on our recommendation with other HP devices, even after several customers willingly contacted HP and were sent warranty replacement new and refurbished units that also failed.  The only three K550 printers that remain in service with us or our customers (one in our office and two others with customers who requested to keep the units we replaced) fail to pick up any paper out of the main tray an astonishing 93%, 98% and 100% of the time, respectively.  This is not an exaggeration, these are documented numbers rounded down when applicable).
    I've perused many online sites, forums and websites on this topic - both professional and non - and found this to be a common problem with what seems to be a very great number of these units.  Some folks also mention a problem with the K/Y (black/yellow) printhead, but neither I nor any of our customers have experienced this problem.  In solving this feeding problem, we've tried different brands, weights and chemical makeups of paper (HP paper works well, but Staples brand paper of standard weight and 97 bright works best), tried different loading strategies for each paper type (such as fanning the paper before loading and before printing, light, moderate and heavy loads in the standard tray), tried installing a duplexing device (HP OEM of course), tried installing the larger paper tray (also HP OEM) and flashing different firmware supplied by HP - all to no avail.  None of the units have any aftermarket parts, kits, ink cartridges or printheads - everything installed and used in these printers is OEM, except for occasional special papers or label sheets.  So where does this leave us?  More importantly - where does this leave my customers who I prematurely recommended this product to?
    We're looking for a solution from HP.  We've tried customer service and have opened several issues without resolution.  I'm tired of my employees and myself dealing with this issue only to be told how to load paper and to flash the same firmware on the same device for the third, fourth and fifth times.  We have 16 defective units in storage and 3 units in partial service for a total of 19 units.  Accounting for these 19 units:  we lightly use 1; we sold and supported 15 of these within our customer base and 3 to our employees, all of which we replaced with other HP products (again, at our cost), and 2 customers decided to keep 1 defective unit each.  As a result, both myself and my company are out big money because of this issue.  We replaced all of our supported K550's with other HP devices only after unsuccesfully attempting resolution with HP.
    If there are replacement parts that address and resolve this conflict available, where can I obtain them?  If there is a simple remedy, what is it?  What can we do to mitigate this situation and yield a positive outcome?  The K550 is an outstanding printer in terms of speed and print quality, unfortunately its unreliability due to poor feeding performance and need for constant supervision and user intervention doom this model to the component recycler's scrap heap.  Do you have a solution?  Are you experiencing the same problems?  I want to know!

    So, I just typed this nice, long post about my SOLUTION to this problem, and apparently the forum didn't like it and deleted it.  I'll have it up in the next couple days. 

  • Quality problem printing in Windows 8.1 with CP1215

    Recently purchased new laptop with Windows 8.1 Pro.  I have had my printer for years, CP1215, via USB, without having any problems printing to it with Windows 7 Pro. I first noticed that the quality of print I receive out of my printer on the new laptop is darker.  The darkness comes from black lines going diagonally across the page.  I would estimate at approximately a 2 degree angle.  I would also estimate that the lines appear every 4th pixel row.  I have attached 2 images, printed on 2 different printers.  The one on the top is the one off of my CP1215, the one on the bottom is a color copier in my office.  I have zoomed in incredibly on the prints to show the lines.  Just never had problems with this printer in pre Windows 8.1 days.  Tried installing ljcP1215-HB-pnp-win64-en.  Tried uninstalling printer, rebooting, then installing, still same problem.  I also have another problem with printing, but suspect it is more of a Microsoft problem.  My laptop thinks a network printer goes offline, stopping and restarting the print spooler service seems to fix that.  I had to make a .bat file on my desktop to do it, it happens at least 2 times in an 8 hr work day.                        

    Hi paulie99, Welcome to the HP Forums, I hope you enjoy your experience! I understand the printer isn't printing properly from Windows 8.I will be happy to help you. Check your printer driver settings. 1. On the File menu in the software program, click Print.2. Select the driver, and then click Properties or Preferences.3. Click the Paper/Quality tab.4. In the Type is or Size is list box, select the correct media type or size. Set the quality to ImageREt 2400. I have provided a document to install the Windows print driver to see if that makes a difference.Installing the Printer Software in Windows 8.1 for a USB or Network Connection. For the network printer I would setup a static IP address. Please let me know the results if you are still having issues. Thank you for posting on the HP Forums.Have a great weekend! 

  • HP PSC 1610 lost Paper/Quality tab in Print Options

    Help! The Paper/Quality tab in Print Options menu has disappeared. Everything prints with max ink. The ability to select draft, fast normal or black ink only has disappeared. I suspect this happened after the last OSX update. I now have 10.4.7
    The problem persists with all software applications

    Thanks for the tip. I did receive a long answer from HP to uninstall and reinstall the updated printer drivers from HP's site. They think something got corrupted. I suspect they are right. After doing the whole procedure it now works fine. Thanks for your help.

  • F2480 - paper feed problem - loud noise

    My F2480 has recently developed a problem with its paper feed. Once I press the Print command for a document etc, there is a loud ratchet sounding noise for about 3 seconds and that's it - it doesn't then feed the paper in. It sounds like machine gun fire.
    This happened after a paper jam when the printer took in a whole wadge of paper in one go for no apparent reason. I cleared the paper jam as you're supposed to and now I am left with this problem.
    The printer is around 18 months old.
    How can I correct this?

    Hi @Trav46, 
    I understand that you can print one or two pages, then a blank page feeds through part way and causing a jam. The printer makes a noise when printing with the refilled toner also. I can help you.
    Did you have this issue before replacing the toner?
    Remove the toner.
    When you turn the printer on, does the printer make a noise?
    When you reseat the toner and turn the printer back on, does the printer make a noise?
    Inspect the toner cartridge for damage:
    1. Remove the toner cartridge from the product and verify that the sealing tape has been removed.
    2. Check the memory chip for damage.
    3. Examine the surface of the imaging drum on the bottom of the toner cartridge.
    CAUTION: Do not touch the roller (imaging drum) on the bottom of the cartridge.
    Fingerprints on the imaging drum can cause print-quality problems.
    4. If you see any scratches, fingerprints, or toner, any other damage on the imaging drum, replace the toner.
    5. If the imaging drum does not appear to be damaged, reseat the toner again.
    Replace the toner with Genuine HP Toner to rule that out.
    If you need further assistance, just let me know.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Print Quality problems

    My print quality for Reds & Greens is coming out streaked. The blacks and blues are fine. I use HP ink cartridges anad keep them cleaned and aligned. But on the Alignment page the reds & greens are streaked and cannot be cognized. Could this be a print head problem ? 

    Hello novemberwolf,
    Welcome to the HP Forums.
    I see that you are having some printing issues when attempting to print in colour.
    Please click on the following link on Fixing Print Quality Problems for the HP Officejet Pro 8600 e-All-in-One Printer Series.
    If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
    Thanks for your time.
    Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    W a t e r b o y 71
    I work on behalf of HP

  • Print quality problems on Fuji Xerox printers when printing from ArchiCAD and/or Preview.

    Hello,
    We experience major print quality problems when printing directly from Graphisoft's ArchiCAD, Nemetscheks Vectorworks and from Apple's Preview.
    Basically we see various artefacts on our printed drawings, e.g. line thicknesses change and hatched patterns / fills are reproduced with patches where the lineweights and clours change completely... which is not acceptable.
    This affects the following Fuji Xerox printer models on both 10.6.x and 10.7.x with the latest FJX PPDs:
    ApeosPort C5540I
    Xerox LF6605 MF
    The workarounds for us are to either print PDFs from Adobe Acrobat Reader or via the rather dated Accxess Tools, besides that we prefer at times to print directly from a given Software it is also not always possible to generate a PDF and print it from Acrobat Reader... especially since the latest Adobe Reader update to its print dialogue makes printing from it extremely tedious - in fact we are considering going back to 9.5.2
    Obviously, we have approached FJX Tech Support and are awaiting a reply - however we are disappointed that this is happening on relatively new equipment and wonder if anybody else has already found a solution.

    The symptoms you mention could be related to the FJX engine and Acrobat is masking this fault. To test, you can create a Postscript file from the print dialog of ArchiCAD or VectorWorks and then download this to the Apeos RIP. If this produces the same result as when using the printer driver from the applications, then it would indicate that the engine is not capable of handling the data being sent to it from these applications.

  • HP Officejet 5610 All-in-one paper jam problem

    Please is anyone out who can heIp me.
    I tried to print a word document from my computer and my printer came up with the following message: Paper jam: clear jam and press ok. I have looked through the printer to see if there is any paper jammed in the printer. I just couldn't find any. This is the first time I have experienced this paper jam problem with my printer.
    On pressing the OK button resulted in the printer making some strange noise (sounding as if it is trying to pickup a paper) with the catridge mechanism sliding from one side to the other for about 10 seconds without a paper in the paper tray being picked up. It then shows the paper jam message again and again. It has been the same for the last 5 hours and I need to print some documents urgently.
    I have tried all of the following troubleshooting I found on the HP website without any joy.
    Step one: Remove any loose paper Remove any loose paper from the input tray.
    Step two: Clear the jam from the back of the Allin-
    One 1. On the rear of the product, press in the tab on the left side of the rear access
    door to release the door. Pull the door away from the product to remove it. Gently pull the
    paper out of the rollers. CAUTION: If the paper tears while being removed from the
    rollers, check the rollers and wheels for torn pieces of paper that might have remained
    inside the product. Loose pieces of paper will cause future paper jams. Replace the
    rear access door. Gently push the door forward until it snaps into place. Press OK to
    continue the current print job. If the issue is not resolved , continue to the next step. If
    the issue is resolved , you do not need to continue to the next step. If these steps
    resolved the issue , there is no need to continue troubleshooting. If the issue persists , see the next step.
    Step three: Clean the rollers Turn off the unit, and then unplug the power cord. Press in the tab on
    the left side of the rear clean-out door to release the door. Remove the door by
    pulling it away from the unit. Wipe the paper rollers with a lint-free cloth lightly moistened
    with distilled or bottled water. Rotate the rollers with your fingers to clean all the way
    around. Allow the rollers to dry completely, and then replace the rear access door. Plug
    the unit back in and turn it on. If these steps resolved the issue , there is no need to
    continue troubleshooting. If the issue persists , see the next step.
    Step four: Clear the jam from the automatic document feeder (ADF) Lift the cover of the ADF. 
    Lifting the ADF cover Gently pull the paper out of the rollers. CAUTION: If the paper
    tears when being removed from the rollers, check the rollers and wheels for torn pieces
    of paper that might be remaining inside the product. Loose pieces of paper will cause
    future paper jams. Close the cover of the ADF. If these steps resolved the issue ,
    there is no need to continue troubleshooting. If the issue persists , see the next step. The
    next step couldn't be done because the paper is not loading. 

    @CAGY, take a look at this HP link on how to clear a jam.
    Please mark the post that solves your issue as "Accept as Solution".
    If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
    I am not a HP employee.

  • I have Mac OS X 10.6.8 and am trying to change a printer to black and white/gray scale. All the posts I find refer to a button for Paper Quality. This does not appear on my options. Just paper handling which does not have a function to change from colour.

    I cannot change the printer settings on my MacBook Pro to gray scale from colour. there is no function for Paper quality, just paper handling. any suggestions greatly appreciated - as long as they work!!

    Was the printer instance properly configured when created, so the print subsystem picked the correct PPD and knows of all the device's capabilities? If in doubt, erase and create anew so you can confirm that the printer maker/model/version is getting correctly identified. This may trigger Software Update to download & install a printer update. The menus available on the print dialog depend on what the OS knows the printer can do. For instance, this is what I get in Safari's print dialog when using an HP 2550Ln color laser at the office:

  • HP 8750 Paper-Size Problem where it keeps telling me the paper is too big (it's set up for 11x17)

    I've got an HP 8750 printer running with a Windows 7 Ultimate machine, and I've got a paper-size problem where it keeps telling me the paper is too big. It's set up for 11 x 17. 
    The actual wording on the printer is: 
    Paper installed is larger than needed. Press cancel to replace with correct size, if you wish to save paper, or press check mark to continue. 
    When you press the check mark it feeds the paper, but for a multi page-document I have to press the check mark for each page to feed.
    How do I get it to print 11 x 17 paper without having to press the check mark for each page?

    ''guigs2 [[#answer-672422|said]]''
    <blockquote>
    NoScript stops cookies, please disable this addon/extension as well as make sure that the language en-us is installed.
    # 1) Open up the Firefox Preferences tab. You can do this by typing about:preferences in the URL bar.
    # 2) Click "Content"
    # 3) Next to "Languages", click "Choose"
    # 4) Select "English/United States [en-us]", click "Add"
    # 5) re-open "about:accounts"
    # 6) Click "Get Started"
    </blockquote>
    Thank you for replying. Unfortunately, I already did all of these things. As you can see from the below screenshot, the language is already set. Also, this screenshot was taken in Safe Mode, so NoScript is not enabled. About:accounts still says I need to enable cookies for some reason. So, this solution didn't work....

  • HP PSC 1515 paper-feed problem

    Hi
    Our HP PSC 1315 has a paper-feed problem, but this does not appear to be a dirty roller: while I can hear motors whirring when the printer wants to feed in the paper, none of the visible rollers turn ― including the single pick-up roller ― and the "check paper" light remains on. 
    Any suggestions? Can you help?
    Thank you
    Michael

    Hi,
    You could try a printer reset.  See the following link:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01577374&tmp_task=solveCategory&lc=en&dlc=en&cc...
    This may help.  However, if the rollers still persist in not moving there may be some mechanical issue with internal gears not engaging.  This would probably necessitate some physical repair so you woul dprobably have to contact HP to find out if there is somewhere that does printer repairs near where you live. See this link:
    http://www8.hp.com/us/en/contact-hp/contact.html
    I hope that this helps.
    ---- If my answer was helpful please click the Kudos star.
    If your problem is solved please click the Accept as Solution button so other forum users can use the solution.---->
    (I am an HP employee) I am not a expert on all our products, but I'll do my best to help you.

  • Paper Alignment problems!

    I have a HP F4280 all in one printer, just recently when doing any type of printing, everything is printed but comes off alignment, that is not straight on the page. How can I fix this paper alignment problem? I've had this printer for 2 years now and just recently the alignment is off, I haven't done anything different!

    The troubleshooting page here may help.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • 4 Questions on New Project Settings with Pemiere Elements 9 - & Fix Quality Problems.

    When I started my new project I selected PAL, DSLR - 1920 x 1080p  - 24 fps.
    Once in New Project, I dragged the movie onto the Timeline, then up poped a box saying something like "Fix Quality Problems", whch I accepted.
    Q1 Which is the best frame rate to record in, to subsequently bring media into Premiere Elements 9?
    I am in The UK so we have PAL and therefore, I could use 24p or 25p   - 25 p is 25 fps, and 24p is 23.976 fps. per the Canon manual.   [NB the Canon will not record at 50 or 60p in PAL]
    Q2, I read somewhere that some Video Editors can not accept a movie file in its native format , and thus change it to a different format and then edit it, and then export and convert it back - often with a serious loss of quality. I would like to maximise the quality.
    Q2i] Does Premiere Elements 9 do this converstion? If so does it harm the quality significantly - are there ways to avoid this?
    Q2ii] and if so, is there a recording format best suited for me to record in,  and subsequently import my videos into Premiere Elements 9?  eg would it be better to record in 25 fps?
    Q2iii]  There was also a screen somewhere about this section like 2,2,3,2,2  I think its something to do with pulldown?  What is the best setting for the highest quality?
    Background info:-
    I shot my videos with my new Canon DSLR 5D MkIII;  I set the movie quality to:-
    PAL, 1920 x 1080p  ALL-I (this was the highest quality the 5DIII can record at, there was an "IPB" option for lower quality).  And I selected 24 fps  - which the manual says is actually 23.976 fps
    The manual also says it is a MPEG-4 AVC/H.264 [movie recording compression] Recording Format = MOV
    But  strangely it loads onto my laptop as a "Quick Time Movie". I was expecting to see a .MOV file. [whether this is because this Sony Laptop comes with 'PMB Organiser' and view software. Or the hated iTunes changed how things are imported, I just don't understand any of this stuff .  All I do know is iTunes repeatedly tried to change my default viewer. So did it change the format, which files are imported in?? [re loading the files from my cameras CF card into my laptop]
    Any advice much appreciated
    Peter

    Peter,
    The way out of the project is encoding. And recoding tends to degradation of the export in varying degrees for different formats. Typically DV AVI undergoes less change with reencoding than the rest. But, we are not dealing with DV AVI here. Your source appears to be
    AVCHD (MPEG4 AVC/H.264) video compression
    1920 x 1080 16:9 @ 24 progressive frames per second
    Rather than export the Premiere Elements 9.0/9.0.1 Timeline to a .mov file or something else and then importing that into Premiere Elements 11 for is AVCHD export, please consider trying to open the Premiere Elements 9.0/9.0.1 project in Premiere Elements 11 and then proceed there to export Publish+Share/Compute/AVCHD with Presets = MP4 - H.264 1920 x 1080 p24.
    Keep in mind that if you take a project created in Premiere Elements 9.0/9.0.1 and edit it in Premiere Elements 11 and then decide to further edit it in Premiere Elements 9.0/9.0.1, cannot do. And, if some unexpected perk allows the opening of the Premiere Elements 11 edited version, there will be problems. Unless there is a special reason, best complete a project in the version that created and create anew in the newer version.
    A just in case note, the original on the hard drive is not altered. Premiere Elements traces back to the original from the Project Assets thumbnail (copy of original).
    But, you should make the comparsion between your H.264.mov opportunity in version 9.0/9.0.1 and your AVCHD.mp4 opportunity in Premiere Elements 11. I believe that you said that is your intention.
    For your Premiere Elements 11 tryout download, check out another browser. I always had to go to Internet Explorer for that download. Firefox never was good for that. But with this version 11, Firefox did the job. I had better results saving the downloaded folder to Documents than I did to Desktop.
    Please review and let us know if I have targeted your questions. If not, please detail what I overlooked.
    Thanks.
    ATR

  • QUALITY PROBLEM FASH STORAGE

    I bough my MacBook Air in 2013, after 2 years using only internet, photos and music, nothing havy, I updated my OS X Yosemite and my computer turned off and never turn on again, with a question folder on it.
    I look for the online support, I made step by step that exist on website and nothing happen. Even the chat support I did! However, nothing change and nobody could help me from apple.
    So, I took my MacBook to the authorized technician support, that even the technical could not explain to me what happend with my flash storage, I totaly lost it.
    I know that have a poor lot of flash storage that was sold between 2012 and 2013, the year I bough, but was in August and they said that the bad quality lot was until June, who guarantee me that was not this quality lot?
    The problem of my computer for sure was a quality problem, I didnt used in a bad way.
    The budged of the service is too high, almost a price of Sansung laptop, and I am wander if someone can give me a solution or something that can help, because apple didnt reply my quality problem, nobody nows why the computer is off and is pretty new.
    I'm out of USA and hope to get my solution soon, because its a disrespect with the consumer.
    If someone can give me a reply, I will appreciated.

    Hi guys
    I have the same problem however I am able to retrieve and play back the audio files but bnot able to retrieve screen capture video files
    I am also migrated it to network storage. Video files are being uploaded to the new location with nno issues but they are not being able to be retrieved any suggestion
    I am getting the following messages:
    The message they are getting is as follows:
    There are two windows appearing quickly saying that the files are decoded and initialized successfully. Then we get the window displaying” connecting to video file please wait while a connection is established
    The message they are getting is as follows:
    There are two windows appearing quickly saying that the files are decoded and initialized successfully. Then we get the window displaying” connecting to video file please wait while a connection is established
    The message they are getting is as follows:
    There are two windows appearing quickly saying that the files are decoded and initialized successfully. Then we get the window displaying” connecting to video file please wait while a connection is established. then is stays there and does not retrieve files
    Abdul

  • Quality problem exporting from FCE

    Hi,
    i have a quality problem exporting from FCE. I have finalized a 30 minute movie and want to send it to friends on DVD or CD-ROM. when i use "export as quicktime movie" the file has 6.5 GB and won't fit on a DVD-ROM. when i use "export with quicktime conversion" and choose quicktime movie with H.264 compression and highest quality the movie goes down to 4.2GB. Now it would fit on a DVD-ROM, but the quality is not good. The picture looks blurred and i see some type of interlace-effect.
    which type of export format do i have to choose to avoid the interlace and blurred pictures? is there a magic format that does not cost that much quality and reduces the movie by 30-40%? or would a video DVD work better? how do i create a DVD? with iDVD?
    thanks for your help!

    or would a video DVD work better? how do i create a DVD? with iDVD?
    That's what Id do.
    Export as QuickTime Movie (reference file is OK) and drop the export to iDVD.
    You will get 1 hour of FCE Timeline on a single sided disc using Best Performance (iDVD setting).
    Two hours using Best Quality (iDVD setting)
    Al

Maybe you are looking for