Set up 2 airports

Running a business from home and need fast internet access, so in my office I have one airport and in the home another. When I try to set-up my work airport I get DCHP errors, I do I correct these errors?

Hi Duane,
Thank you for your reply. I looked at the dual band network set up. That is not what I need. I am trying to have internet access in two buildings w/o paying for two internet hookups. I want to extend the range of the new 802.11n airport into a second building. I found instructions for "Using the AirPort Admin Utility to create a WDS network with multiple base stations". This seemed to be the answer but the Airport Admin Utility doesn't work on the 802.11n. I have to use the software that came with it the "Airport Utility" to set it up. There is not a place in that utility to set the 802.11n up as a WDS. I can do it with the old aiport but not on the new. Do you have any other suggestions for me?

Similar Messages

I was setting up my Airport and thought the first set up did not go through, so I set up again and I ended up with two accounts instead of one. How can I manage to have only one account now? Thanks for the help.

I was setting up my Airport and thought the first set up dod not go through, then I set up again and ended up with two wireless accounts. I use it for the prointer and the iPad, and I can see both accounts in the iPad. How do I get rid of one account? Thanks for the help!

me.com accounts can be used for iCloud. See the FAQ section in:
<http://support.apple.com/kb/ht4895>
but it may be too late if you have already created a new AppleID.
A few years ago Apple said they were working on allowing account merging, but it never happened (maybe objections from copyright holders).

How can I set up mhy Airport Express to extend my Time Capsule wifi wirelessly

I want to extend my wifi off my Time Capsule with an Airport Experess in a part of my house that has no data cable ran to it. How do I do this?
Thanks

No more meseges.
في ٢٦/٠٨/٢٠١٤، الساعة ٢١:٤٥، كتب Apple Support Communities Updates <[email protected]>:
New discussion activity
Bob Timmons has posted in the AirPort community.
How can I set up mhy Airport Express to extend my Time Capsule wifi wirelessly
Assuming that you have the model A1264 or A1392 version of the Express, it must be located where it can receive a strong wireless signal from the Time Capsule to be able to extend it correctly.
A good general location would be a point that is about half way between the Time Capsule and other area that needs more wireless coverage.
You will use AirPort Utility on your computer to configure the Express. An iPhone or iPad could be used as well.
We can provide more help....if you need it....but we'll need to know what version of AirPort Utility that you are using on your computer....or whether you want to use an iPhone or iPad to setup the Express.
https://discussions.apple.com/servlet/JiveServlet/downloadImage/2-26506753-46613 2/AboutAirPortUtility.png
To post a reply, go to the discussion in Apple Support Communities.
You are receiving this email from Apple Support Communities. You can change your email preferences in your Apple Support Communities Profile.
TM and copyright © 2014 Apple Inc. 1 Infinite Loop, MS 96-DM. Cupertino, CA 95014.
All Rights Reserved | Privacy Policy | Terms of Use | Apple Support

How to set up an AirPort Express using static IP with internet provider limitations?

I am trying to set up an Airport Express to act as a wireless router (for multiple users to use) and I have some limitations with my ISP provider...my ISP provider restricts access to the internet for each device by only providing/issuing one IP address to one device (so they charge extra for multiple attached devices). So only one device can access internet via an IP address (they link the device's MAC address to that specific IP address, therefore limiting internet to only one device).
My ISP provider has provided me with the following info:
- IP address
- Subnet Mask
- Router Address/Gateway
- DNS servers (4 were provided)
- domain name
I was trying to work around the ISP provider so I don't get charged using multiple devices so I was configuring my Airport Express with the info provided (ie-IP address, subnet mask, etc.) by configuring the IPv4 "manually" using a static IP. After plugging in this info using AirPort Utility, I was able to get access to the internet through wifi/Airport but only if the bridge is disconnected and only with one device at the time (trying to use another device to access the WIFI from the Airport Express gave me the error "can't access the internet because the IP address 128.xxx.xxx.xx" is already in use by another user).
I tried different angles such as changing the router mode to 'DHCP and NAT' (which doesn't yield any access to the internet on any device; I get the amber light blinking on the Airport device). When attempting to change the DHCP range, I get an error saying "the range provided doesn't work" (not exact wording).
The only other thing I haven't tried is to supply my ISP provider with the MAC address of the Airport Express device. Does anyone know if this would work and, if so, would I be able to use my Airport Express as a wireless router?
Unfortunately, I can't switch ISP providers as this provider is the only one I can use in the area (so frustrating!!) so I have to try to work around the system. Please help!!
Note: my Airport Express is the new model (I bought it a few weeks ago) and I have tried connecting to it using Airport Utility version 6.3.2 with Mac OS X 10.9.4 and OS X 10.9.2

Welcome to Apple Support Communities
If your PC hasn't got a disc drive, download AirPort Utility from the Apple website to set up the AirPort Express > http://support.apple.com/kb/DL1547?viewlocale=es_ES

How to set up the airport express with a linksys wireless-g broadband router

I need to know if and how to set up an airport express to use to extend a home wi-fi network. I have AT&T service with a 2WIRE modem. I am using a Linksys wireless-G broadband router. I also have the new Macbook Air notebook. The airport express keeps giving me a blinking amber light even when the ethernet cable (from the modem) connected. Please let me know how to set up an extended wifi network using this system. Any help would be appreciated.

If that is all that is done, the Express would not provide more wireless coverage. Instead, it would duplicate the coverage provided by the Linksys and there would be two WiFi systems covering approximately the same area. As per my above comment, one Express connects via Ethernet to the Linksys. The second Express provides the extension.
You must have misunderstood what I was saying.
Linksys is providing a wireless network.
The Express is connected to one of the LAN ports on the Linksys router using a long Ethernet cable (or Ethernet powerline adapters)
The Express is located on the other side of the house, for example.
The Express is configured to create a wireless network using the same wireless network name, security and password as the Linksys router
The Express is configured in Bridge Mode
This has worked quite well for me for years. Computers "switch" from one wireless access point to another smoothly and automatically while they move around the house.
Although this is an "extended" network, it is technically known as a "roaming" network.
This is what I was suggesting as a possible alternative without having to buy more hardware.

I have a linksys WRT54G router that we use as a base. I want to use Airplay using Airport Express and hook up my stereo to it. How can i set up my Airport express without a PC/laptop? I just downloaded Airport utility on my iphone and ipad,will that work?

I have a linksys WRT54G router that we use as a base. I want to use Airplay using Airport Express and hook up my stereo to it. How can i set up my Airport express without a PC/laptop? I just downloaded Airport utility on my iphone and ipad,will that work? And one more thing about the setup, the linksys router shich acts as a base is in a different room as the airport express which i wanted to use for airplay. So I'm hoping to hook up the Airport express via wireless signal. If i can set it up, can someone pls help me out by posting detailed instructions. Thanks so much!

The first message that AirPort Utility will display during the auto setup will be that the Express will be confgured to "extend" the network. When AirPort Utility analyzes the network further, and sees that the Express cannot "extend" the 3rd party network, the next message will indicate that the Express is being configured to "join" the wireless network.
Once the Express is configured, if you later go into AirPort Utility to check the settings under the Wireless tab, you will see that the Wireless Mode is indeed "Join a wireless network".

How do I set up multiple Airport Expresses to connect over ethernet for Airtunes only?

I am trying to set up an Airtunes network using an Airport Extreme and three Airport Expresses connected together via ethernet (CAT5 cable). At each Airport Express there will be a speaker setup. I don't need/want internet connectivity on the network, but not sure if it is required for setup or not. I have made this work over wifi, using the Expresses to extend the network, but struggling to get this to work over ethernet.
I would be verry grateful of a step-by-step method to setting this up! I am also looking to set up 6 airport expresses to do the same thing in another location.
Thanks in advance!

Thanks for the info.
I assume that the AirPort Extreme is setup and working at this point.
Work with one AirPort Express at a time to get them all configured, and then you can locate them where they will be needed.
AirPort Setup will configure the Express devices to "extend a wireless network" using Ethernet, so they will be broadcasting the same wireless signal as the AirPort Extreme and provide more wireless signal coverage as well.
I have yet to meet the first person who thought that they had too much wireless coverage, but you would have the option to turn off the wireless on the Express if you wanted. Most users like having extended wireless for their devices.
Temporarily, move an Express close to the AirPort Extreme
Connect a spare Ethernet cable from one of the LAN <-> ports on the Extreme to the WAN "O" port on the Express
Power up the Express for a few minutes
Hold in the reset button on the back of the Express for 10 seconds and release. Allow a full minute for the Express to restart to a slow, blinking amber light.
Click the Airport icon at the top of the Mac's screen and wait a few seconds for AirPort Express to appear just under the listing of New AirPort Base Station
Click directly on the AirPort Express
AirPort Setup will open up automatically and take a minute to analyze the network, then announce that the Express will be configured to extend the AirPort Extreme network.
Enter a device name that you want to use....example.....Express1.....and click Next
AirPort Setup will configure everything for you. Notice that the message will say that the Express is being set up to extend using Ethernet. When you see the message of setup complete, click Done.
Now you can move the Express to the remote location where it is needed, hook it up to the Ethernet connection there, power up the Express and set up AirTunes on the device.
AirTunes is enabled by default, to other than make the speaker connection, you won't have much to do on that.
Set up other Express devices the same way, except assign a different name to each device....example....Express2, Express3, etc.....to keep things organized.

How can I set up an Airport Extreme as a router, in conjunction with my AT&T modem/router?

I am trying to set up an Airport Extreme as my router, and I am currently using an AT&T modem/router combo. I am wondering what would be the easiest way to do this. Any help would be appreciated. Thanks!

Connect an Ethernet cable from one of the LAN <-> ports on the ATT modem/router to the WAN "O" port on the AirPort Extreme. This cable must remain in place permanently.
Open Macintosh HD > Applications > Utilities > AirPort Utility on your Mac
Click on Other WiFi Devices
Click on AirPort Extreme xxxxx
The utility will take a moment to analyze the connection, then a screen similar to this will appear with your AirPort Extreme instead of an AirPort Express
Type in a short simple name that you want to use for the wireless network
Type in a device name for the AirPort Extreme
Enter a password that will be used for both the AirPort Extreme and wireless network
Verify the password
Click Next
The utility will setup everything for you. When the message of Setup Complete appears, click Done and close AirPort Utility.
The AirPort Extreme wireless network is now available.

I just set up the airport wireless modem - with a comcast internet router - all wireless device connect seemlessly (3 Iphones, Mac Air, and a Sony Laptop) but my IPAD 1 no longer connects. It tries to but never connects. I have reset it and have utility

I just set up the airport wireless modem - with a comcast internet router - all wireless device connect seemlessly (3 Iphones, Mac Air, and a Sony Laptop) but my IPAD 1 no longer connects. It tries to but never connects. I have reset it and have airprot utility app downloaded on my IPAD - it shows the modem and the internet no connected?

Do you mean an Airport Extreme Base Station connected to a Comcast Modem?

I want to set up my Airport Express Base Station again but do not remember how. Please walk me thru it.

I am trying to hook my Airport Express Base Station up to be a router again and have forgotten how to do this. Before I had it hooked through the modeum and would like to have it that way again but for some reason the process has completely left my memory. I know it has something to do with the little icon on the top of the computer but not what it has to do with it. Because it is not hooked up I am unable to get my printer to work unless I connect to another wireless that I have but do not want to use all of the time since I have to pay for it and do not have many GB. I am also paying for another that I want to use all of the time (unless necessary to use the other) so It only cost me when I am away from home. Please walk me through the process of hooking the Apple router back up.

All apple routers are setup via Airport Utility.. there is no icon for it in the top menu area.. I think you are confusing the airport network setup (ie the internal wireless card in the Mac) with the airport express setup.. Apple insist on calling everything the same name which makes it more confusing.
Open the airport utility which you find under applications/utilties.
Router setting will depend on what version of the utility you are using.
In version 5 it is under Internet tab and in v6 utility under network. You need to set it to DHCP + NAT.
Download and read the manual for setting up the express if you have forgotten the details.. manuals are always good.. all the manuals are listed at the head of the section. But you are in Time Capsule instead of extreme/express specific area.
https://discussions.apple.com/community/wireless/airport
Manuals link http://support.apple.com/manuals/%23airport
If you want the express as router the modem should be bridged or it should be a pure modem for it to work without Double NAT issues. There is nothing wrong with bridging the Express.. that is not the same as using it in wireless bridge modes.. that is router bridge.
What modem do you have?
I am at a loss to understand the rest.. why the printer is not part of your own network.. and how setting up the airport this way is important. You need to give us specific details if you need more help.
How exactly is the airport setup now?
How do you connect to the modem?
How is the printer connected? What kind of printer?

How do I set up my AirPort Extreme to provide IP addresses without being connected to the Internet?

II'm trying to set up my AirPort Extreme in the field without an Internet connection so that devises can communicate wirelessly but there aren't any IP addresses being generated

Just run the AE in router mode.. if you have difficult with the setup do it completely manually..
This is how I do it.
Airtport Utility can't find Airport Time Capsule on either of my 2009 Macs
As long as the AE is running in DHCP and NAT mode it will produce IP addresses.. however you cannot turn off WAN.
You could give it a static IP .. so set to static instead of dhcp if you like.. eg.
DNS and WAN errors.. double NAT, Ethernet unplugged, etc.. so it makes no real difference..
The AE will function fine as router (Wireless AP) to your network however..
Just ignore all the errors.

How do I set up my airport express to make a connection with my Hp? I already have it set up for my mac laptop just not sure how to set it up so that theres also a connection with my Hp

how do I set up my airport to make a connection with my Hp? I already have it set up for my mac laptop just not sure how to set it up so that theres also a connection with my Hp

I set up my new HP Descjet 3054A . I had a problem becouse Apple give me CD as a driver. The thing was that CD wasn good for this printer becouse it was old software:) I had to go to Apple store so the specialist had to download me he wright driver. Becouse I didnt wannet to screw this up . When he downloaded driver I fired it up at house and thingworks perfect. The thing is when you download all the software from HP side . Then you have to connect your MAC to printer via USB . Fallow the instructions it should works. Worked for me. Good Luck!

How do i set up my airport express to my pc?

how do i set up my airport express to my pc. all i see is an amber light flashing on it?

Hi
Take a look at this page for general windows info regarding airport express:
http://www.ifelix.co.uk/tech/airport.html
Assuming your computer connects to the network you want to allow your girlfriend to access you will find the password you require in your keychain.

How do i set up my airport extreme to access from my work windows based PC

How do I set up my airport extreme to access from my work windows based pc?

To mount the AirPort Disk in Windows 7 or Vista:
Open the Network browser by double-clicking Network on the Windows Desktop.
The AirPort Extreme base station name should appear in the browswer.
Double-click the name and you should get a login prompt.
Now depending on how you set up disk access:
In the Name field, either enter the user account name or for base station/disk access, leave this field blank.
In the Password field, enter the base station, disk, or user account password.
Select the volume(s) you want to mount, and then, click OK.

How do I set up my Airport Extreme to best use multiplayer games locally

How do I set up my Airport Extreme to best use multiplayer games with my family. Everyone is located in the same house and uses the same router.
I have tried a few games but have not successfully connected 2 players

That is a weird question, as your GAMES could be interpreted a hundred different ways. Are we talking about third party devices here or what?

My Airport wireless is working for my two MacBook Pros and my daughter's iPod, but our iPad, Iphone and other iPod all say they need to set up an Airport Base Station but do not have the proper software. I'm not sure what to do to remedy this situation.

My Airport wireless is working for my two MacBook Pros and my daughter's iPod, but our iPad, Iphone and other iPod all say they need to set up an Airport Base Station but do not have the proper software. I'm not sure what to do to remedy this situation.

This might sound like a silly question, but are you sure the iOS devices (iPhone, iPad, iPod touch etc.) are still trying to connect to the same network from your own Airport router, as the MacBook Pros are? If you tap Settings on them, is the network name next to where it says Wi-Fi, the right one?
I've got a weird feeling that either in the past couple of days, a neighbour got an Airport device and hasn't set it up yet (causing your iOS devices to try to help), or that perhaps there's an issue with your Airport router and they're noticing it and trying to help out, while for whatever reason, Airport Utility isn't opening itself on the MacBook Pros like it normally should if there's a problem.
If you open Airport Utility on one of the MacBook Pros, does it report any problems with your Airport device, and can you view/edit the settings on it?

Set up 2 airports

Similar Messages

Maybe you are looking for