Single ap and multiple ssids

Hi Every body!
Is it possible for sinle "AP" to have ultiple ssids, If yes, then it must effect the performance as " ap" has to send beacon for each ssid then switch the traffic from each ssid.
Could anyone explain me this please?
thanks a lot!

Yes, Cisco APs can now support up to 16 SSIDs. And you're correct that it must beacon for each one, so you should be smart about how many you use. Simply use the minimum of what you need!

Similar Messages

1242AG Bridge, VLAN and Multiple SSIDs

I have two buildings that I'm trying to configure a bridge in between them using 2 1242AG APs.
Building A
PCOFFICE SSID on VLAN 200 Radio G
ROOT_1 SSID on Native VLAN 1 Radio A
Root Bridge
Building B
FDAPC SSID on Native VLAN 1 Radio G
ROOT_1 SSID on Native VLAN 1 Radio A
We are using directional antenna. I know they are lined up properly because I have them both down and in front of me. I'm getting an error on the Building B AP that says "
No SSID with VLAN configured. Dot11Radio1 not started." and I'm unable to get this to work. The bridge was working before I added the VLAN and encryption/WPA information for the PCOFFICE and FDAPC SSIDs
Any assistance would be amazing. Thanks! Please see attached files for configurations. I know the switch is configured properly because I had this working before and forgot to save the damn configuration off the devices. I'm not having to do it over from scratch.

That did not work.
I've managed to fix the ROOT_1 and FDAPC... now I'm having an issue where I can attempt to connect to the PCOFFICE SSID but I'm unable to get a DHCP address from the server.
Here is the config for the AP with PCOFFICE on it and the switch.
SWITCH
interface GigabitEthernet3/2
switchport trunk allowed vlan 1,200
switchport mode trunk
interface Vlan1
ip address 192.168.3.4 255.255.255.0
interface Vlan200
ip address 192.168.30.2 255.255.255.0
ip helper-address 192.168.3.98
ip default-network 192.168.3.0
ip route 0.0.0.0 0.0.0.0 192.168.3.1
no ip http server
ACCESS POINT
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP1_ROOT_AP
enable secret 5 REMOVED
ip subnet-zero
no aaa new-model
dot11 vlan-name VLAN1 vlan 1
dot11 vlan-name pcCopper vlan 200
dot11 ssid PCOFFICE
   vlan 200
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 REMOVED
dot11 ssid ROOT_1
   vlan 1
   authentication open
   authentication key-management wpa
   infrastructure-ssid optional
   wpa-psk ascii 7 REMOVED
dot11 network-map
dot11 arp-cache optional
power inline negotiation prestandard source
username Cisco password 7 REMOVED
username admin privilege 15 password 7 REMOVED
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 200 mode ciphers tkip
ssid PCOFFICE
speed basic-2.0 5.5 11.0 12.0 18.0 24.0 36.0 48.0 54.0
no power client local
power client 17
power local cck 17
power local ofdm 17
channel 2462
station-role root access-point
antenna receive right
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 port-protected
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.200
encapsulation dot1Q 200
no ip route-cache
bridge-group 200
bridge-group 200 subscriber-loop-control
bridge-group 200 block-unknown-source
no bridge-group 200 source-learning
no bridge-group 200 unicast-flooding
bridge-group 200 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers tkip
ssid ROOT_1
dfs band 3 block
speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0
no power client local
power client 11
power local 11
channel 5180
station-role root bridge
antenna receive right
antenna transmit right
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
hold-queue 160 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0.200
encapsulation dot1Q 200
no ip route-cache
bridge-group 200
bridge-group 200 spanning-disabled
interface BVI1
ip address 192.168.3.241 255.255.255.0
no ip route-cache
ip default-gateway 192.168.3.1
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
line vty 0 4
login local

Per Diem Calculations for Single Day and Multiple Days

Hi Gurus
I have just now confronted a weird calculation of Per Diems.
I have configured Per Diems for 1 Day say $50 per Day, irrespective of the no.of hours.
When I create a trip for a single day, the system is calculating $50 Per DIem for one day.
Whereas, when I create a trip for 3 days, the system is calculating only for Two days i.e, $50x2=$100 and not $150 as expected, meaning the lfirst and seond day gets calculated and the last day is not getting calculated
Please let me know where I am missing the little configuration in order to let the system calculate for multiple days correctly ?
This is an urgent requirement please.....Need help.
Thank you
RRoy

Hi,
As I told you earlier that there could be serval options which needs to be checked again.
For example:
a) V_T702N_D
b) Your per diem table
I think if you have checked 24 hours in V_T702N_D , then please verify the trip duration on PR05
If it was working earlier then below might help you...
For Example:
Start date/time 23-July-2011 Time 00:00
End date/time 25-July-2011 Time 00:00
Here above number of days are three (23,24,25) but calculation for meals shall be done for two days, because for three days per diem calculation it shall be 48:01 Hours above is 48 Hours..
Please try in PR05 and check the results.
Start date/time 23-July-2011 Time 00:00
End date/time 25-July-2011 Time 00:01
So please check again and let know in case of problem..
Regards,
Muhammad Umer

Comparision between single Plant and multiplant.

I am doing practice for creation of one organization structure,
At the starting i have one plant under which their are 3 storage location located in different cities.
The Value of material is same in all cities, now i think define each storage location as plant, then what effect will get on the
business.
Can anyone explain me the advantages of multi -plant against single plant?
which process is beneficiary for business process?
Thanks;
Baya Jo.

Hi
At the starting i have one plant under which their are 3 storage location located in different cities
1 ) see first storage location never situated far way from plant its in different cities it should be plant or warehouse or depo
If manufacturing activities happen there then it should be plant
If its only for saleing purpose ,then it will depo ,or only storing purpose it will warehouse
pupose of this ( if you have all three plants ,you get valuvation differntly for each plant )
If you have single plant ,no mater but valuvation will be at single plant level,you cannt get valuvation per citied for you business for you material and releates things
my suggestion consider it plant or depo if it in differnt cities
Regards
Kailas Ugale

Reconcilation- single RO and multiple ITresource- lookup group recon

I added ITresource as key,
usecase:
for server1 i have some groups(ITresource1)--> i want run lookup recon for the server1 and ITresource1 to get server 1 groups
for server2 i have some groups(ITresource2)--> i want run lookup recon forthe serve2 and ITresource2 to get server 2 groups
In RO when i select the ITresource1, i have to get server1 groups(in lookup) only
Thanks

You will need to create your own query that uses the SVR_KEY being the same as the beginning of the lookup.
-Kevin

WAP4410N and multiple SSIDs on different VLANs using RADIUS

I am trying to setup the above environment. When I connect on my guest network it does not give me an IP address from my guest network DHCP scope that is configured on my CISCO router.
Does anyone have any idea how to set this up???
Any help would be appreciated...

It is most likely (I'm not certain from the description) that
the 'sub-buttons' are a 'child' MC of the main button? if so, the
'on' handler for the 'main' button will override any handlers
attached to 'child' buttons within it. the only solution is to use
a hitTest method for either the 'parent' button or the 'child'
buttons, OR separate the two MCs and use the 'main' button to bring
a MC of the 'sub' buttons to the Stage.

Single Source and Multiple Destinations.

Hi all,
I am working on the scenario like Jdbc to Two destnations(SAP and Jdbc).I am able to sent the data from Jdbc to SAP.I have to send the data parallelly or serially to another destination(JDBC).
Could anybody suggest the steps briefly.
Thanks & Regards
sekhar.

Hi,
If you want to send the data in parallel, just configure two receivers in the receiver determination.
Use BPM only if you want to implement a more complex scenario, such as waiting for a response from SAP before sending the messgae to jdbc, deadline monitoring, exception handling etc.
Regards
Manish

Difference between Multiple single values and Selection option variables

Hi !
Can any one tell me the difference between variable types:
Multiple single values and Selection option?
I used each one of them for selecting values for a characteristic but could not notice a difference in choosing values.
Is there some difference in functionality or can they be used interchageably?
Regards,
Sri Harsha

Harsha,
When you go for slection option, in the variable input screen you will be having a button in the last where you can give your slections. There you can maintain either multiple single values and Multiple intervals or else not equal to also..
Just check out there... you will be having tabs for each..
Assign Points if it helps
Gattu

Mail Adapter - Multiple mail ID and multiple mail servers config.

Hi All
I am doing BPM synch scenario in which i get the response from SAP box and send the response via email adapter. I am using mail.xsd and doing mail config. in message mapping. However in the TO field i am able to give only one email ID. If i give multiple email ID's mail is not received. I tried comma and semi-colon as separator. Still not working? I have two questions in configuring TO option:
1) How to send to multiple id's? I am using Lotus Notes.
2)How to send to multiple mail servers? I have to send to Lotus Notes id's and outlook express id's also simultaneously.
Thanks for your help in advance
Warm Regards
Samuel

Hi,
Please find here with some observations about it,
1) How to send to multiple id's? I am using Lotus Notes.
If you have specified an IMAP server under URL, the message is saved in the specified folder but is not sent to the receiver specified under To.
Then even if Under To, you had specified the e-mail address that will receive the message would be separated with a semicolon. It will not work.
Please verify about it .
The below link will also help you to verify if there is anything missing
Mail Adapter (XI) - how to implement dynamic mail address
/people/michal.krawczyk2/blog/2005/03/07/mail-adapter-xi--how-to-implement-dynamic-mail-address
BPM:Single Sender and Multiple Receivers based on synchronous
exchange(switch) part-1
/people/prasadbabu.nemalikanti3/blog/2006/03/10/bpmsingle-sender-and-multiple-receivers-based-on-synchronous-exchangeswitch-part-1
Generic Message Interface in SAP Exchange Infrastructure Email Integration Scenarios
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/00d5a235-4803-2a10-f682-889d67c69975
(If your using Alert Framework then)
If you want to send it to multiple email addresses and all email addresses are user of XI then you can define "Role" and attach that role to everyuser and make this role as receipent of alert .
Thanks
Swarup
Thanks
Swarup

Single access point with multiple ssids and single channel possible?

Hi everybody.
I have this silly question.
Let say we have three vlans, vlan1,2,3 and they are mapped to wlans as follows:
Vlan 1 ssid1
Vlan 2 ssid2
Vlan3 ssid 3
AP --------trunk------Switchted network.
Our Ap has mobile devices in three wlans, i.e ssid1ssid2 and ssid3
Since AP uses half duplex mode, mobile devices need positive ack from ap before they can send data, therefore once channel let say channel 3( assuming 802.11b is used) can be shared by all mobile devices in three wlans.
Is my understanding correct?
Thanks and have a great weekend.

Hii ,
Yes ,that is pretty much possible as suggested by other experts on board. Depending on your access point you will have 1 (2.4 GHz) or both 2.4 & 5GHz radios.
You can configure multiple SSIDs (up to 16 ) known as MBSSID mode in autonomous environment. In Controller based architecture you can configure up to 512 WLAN (SSID) and transmit any 16 of them per AP (using AP group feature). However , it is recommended to keep multiple SSID count below 8 as for each SSID separate beacon will be sent on air which consumes more air time.
Hope this helps
Thanks
Vinay

Is it possible to do multiple ssids and encryptions on an autonomous AP without vlans?

I got a customer who just has autonomous APs. They are upgrading from 1210s to 1262s. They are currently running a config that is wide open with no authentication or encryption and using a VPN tunnel on the wireless clients for security. They want to switch to using WPA2/PSK with the new APs. They have existing clients that have to continue to work during the upgrade to the new APs. They run 3 shifts so it is a 24 hr operation with no downtime. What I was thinking would be to configure the 1262 with multiple SSIDs, one with their existing settings and one with the new. Then I could swap the APs one at a time and it would only impact service for a short period of time while I was mounting the new AP. Then once all the new APs are installed I could transition the clients over to the new SSID and encryption then disable the old SSID once all the clients are switched over. I've done this before with a WLC but not with an autonomous APs. The only config examples I can find uses VLANs. This customer is not using VLANs. Is there anyway to use multiple SSIDs with different encryption on a single radio on an autonomous 1262 without VLANs?
The site has about 30 APs and 100 clients. Yes I know a controller would be preferred for a site of this size but that is a question for sales and why they didn't see them a controller. I just get stuck with what they sell them.
thanks

Hi Don,
Im afraid on the autonmous platform you can not map multiple WLANS to a single vlan.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

WAP200 and .1x/radius authentication with multiple SSIDs

Apparently it's not possible to define more than a single radius server when using multiple SSIDs with WAP200. Unfortunately WAP200 doesn't add the name of the SSID as a radius attribute, so it's not possible to make distinction whether the user is trying to log in to SSID A or B. Does anyone have any ideas or workarounds for this limitation? Of course the best solution would be if Cisco/Linksys fixed the firmware so that the SSID of the logging in user would be sent to the radius server as an extra attribute or appended to the client mac address.

Security option for an SSID can be unique and can be configured when you configure a SSID or under VLAN . Note that each vlan is uniquely mapped to induvidual SSID.

NAC Guest Server and Multiple Guest SSID's/Splashpages

Hi All,
If I have multiple guest SSID's on a single controller and I use NGS as the Radius. How do I configure NGS to "send" the clients to differnet login pages corresponding to the SSID they came from.
I can configure different splash pages in HotSpots section but how do I map the different SSID's from the controller to the different splash pages. Then I guess that raises the question when I generate guest users on NGS is it possile to only allow them associate to a specific SSID.
TIA,
Eoin.

Hi Nicolas,
Thanks for the reply. I can see that config on the WLC and have used it before where there is only a single guest SSID. What I dont know is if the NAC Guest server sees radius requests coming from different guest SSID's on the same WLC. How does the NAC Guest server apply the correct guest policy to that user. And when sponsors genereate guest accounts how do they specific which policy is to be applied to that guest so it can only get access to a specfic guest network/SSID I'm not sure where the "mapping" of accounts/splash pages/policies takes place on the NAC guest server. I've only ever set up NAC Guest when there has been a single guest SSID.
Regards,
Eoin.

I have multiple SSID, but want users of a single SSID to be redirected to a HTTP or HTTPS URL (LAN SERVER for authentication)

Hi team,
I have multiple SSID, but want users of a single SSID to be redirected to a HTTP or HTTPS URL (LAN SERVER for authentication)
I am very curious and it is important. I want to see how to achieve this with CISCO WLC !!!

http://10.229.3.99/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=10.229.3.99/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=www.geo.tv/
I wanted if someone connects to WLAN "MO-GUEST" automatically the user should be redirected to http://10.229.3.99/login.html and once authenticated by 10.229.3.99 , he/she should be allowed to access anything as normal. [ actually i just want automatic url redirection for the first time for the user of wlan "MO-GUEST"
waiting expert opinions.

HT2688 Working on a single computer with multiple users, I have set things up to allow each user to view and listen to the others' music libraries under the "Shared Library" function. Can you then connect an iPod touch and copy music from a shared librar

Working on a single computer with multiple users, I have set things up to allow each user to view and listen to the others' music libraries under the "Shared Library" function. Can you then connect an iPod touch and copy music from a shared library?

Was your wife logged into the libray at the time you tried to log in? I have had a similar problem and it was because another user was logged into the library when I attempted to. I got the permission denied banner.

Single ap and multiple ssids

Similar Messages

Maybe you are looking for