Solaris 10 support on Sun Storedge 6120/6020

Hi ,
I have bought a SE6120 arrays attach to two Sun Fire 4800 as cluster
shared storage with Solaris 9 OS. I intend to upgrade the OS to Solaris 10. But after find the information at sunsolve.sun.com, it not mention about wether Solaris 10. Hope somebody will provide me solution..
Thanks in advance !!
Message was edited by:
Mohd.Suhaimi

The array is supported with Solaris 10. The noticeable change from prior OS is that the SAN drivers and packages are included with the base OS. You do not need to add anything as you did for Solaris 9 and 10.

Similar Messages

Install SUN StorEdge L280 to Solaris 10 x86

Hi, i need help with install & configure SUN StorEdge L280. I have SOLARIS 10 x86 platform on HP DL 380 g3. I need help with this. I dont understend what with this, what drivers is need... On sparc is all ok with veritas netbackup, but on x86...any help?thanks

i need help with install & configure SUN StorEdge L280. I have SOLARIS 10 x86 platform on HP DL 380 g3. I need help with this. I dont understend what with this, what drivers is need... On sparc is all ok with veritas netbackup, but on x86...any help?thanks
The L280 (or HP SureStore Autoloader 718) contains a DLT7000 drive. There is no reason why the generic SCSI tape driver doesn't support these drives.
If you're asking for software to control the autoloader, a similar software like Veritas NetBackup is required. Veritas supplies a replacement driver.
Now I see why your L280 doesn't work with your HP server. The L280 requires a HVD (High Voltage Differential) SCSI controller. The standard SCSI interface is SE (Single Ended) or LVD (Low Voltage Differential). Neither SE nor LVD are compatible with HVD. You won't see the device and can even damage the device and/or the controller.
Get a HVD SCSI controller (Symbios SYM22802, Part-No 375-0006) or Adaptec AHA-2944UW (not AHA-2940UW which is SE!!).
The Sun labeled HP Autoloaders (StorEdge L9, L280) use HVD SCSI while the original ones (SureStore 1/9, 718) use LVD or SE SCSI.
Michael
Robert,
any update ?
Message was edited by:
MAALATFT

Veritas Volume manager 4.0 with Sun StorEdge 3310 D

I am running into a problem. The vxconfigd deamon always dump core when rebooting.
Our environment is listed below.
OS environemt.
     SunOS server1 5.8 Generic_117350-43 sun4u sparc SUNW,Sun-Fire-V240
Software installed.
     Sun Cluster 3.0
     Veritas Volume Manager 4.0 MP2.
Disk Array associated.
     Sun StorEdge 3310 D.
I looked up veritas.com and find Array Support Library (ASL) for Sun StorEdge 3xxx Series is recommended. But I didn't find this library is running on this server.
Please refer to this following link
http://support.veritas.com/docs/277923
As our system is one of critical systems and I'd like to confirm that I can follow up this procedure without doing harm things to our system.
Jeff

No problem Jeff :)
I took a look at the Veritas doc and you're right it does seem to cover everthing.
Has the vxconfigd core dumped since the start? ie from the moment it was installed?
I have installed VXVM 4.0 with Solaris 8 but without the ASL and this worked ok, I know that's not much help to you but I am not sure the ASL will help. Mind you I have not installed it with Sun Cluster 3.0.

Solstice backup 6.1 hang when invoking the autochanger "SUN Storedge L8 "

My company have a SUN Storedge L8 attached to a SUN Solaris 9 (SPARC) while I can only do a tar to the /dev/rmt/0, whenever I tried to interact with the jukebox with the solstice backup, the program hang definitely.
grep '/usr/kernel/drv/lus' /var/sadm/install/contents
/usr/kernel/drv/lus f none 0555 root bin 34624 12073 993189557 SUNWsbus2
/usr/kernel/drv/lus.conf f none 0444 root bin 3754 45438 993190441 SUNWsbus2
/usr/kernel/drv/lus32 f none 0555 root bin 33444 4422 993213667 SUNWsbus2
pkginfo -l SUNWsbus2
PKGINST: SUNWsbus2
NAME: Solstice Backup (Backup/Recover) Device Drivers
CATEGORY: system
ARCH: sparc
VERSION: 6.1,REV=Build.186
BASEDIR: /
VENDOR: Sun Microsystems, Inc.
PSTAMP: gelato010622054128
INSTDATE: Apr 08 2003 13:25
STATUS: completely installed
FILES: 48 installed pathnames
44 executables
37896 blocks used (approx)
this machine has installed the solstice backup manager
pkginfo | grep -i Solstice
system SUNWmibii Solstice Enterprise Agents 1.0.3 SNMP daemon
system SUNWsacom Solstice Enterprise Agents 1.0.3 files for root file system
system SUNWsadmi Solstice Enterprise Agents 1.0.3 Desktop Management Interface
system SUNWsadml Solstice Launcher.
system SUNWsadmx Solstice Enterprise Agents 1.0.3 Desktop Management Interface Libraries (64-bit)
system SUNWsasnm Solstice Enterprise Agents 1.0.3 Simple Network Management Protocol
system SUNWsasnx Solstice Enterprise Agents 1.0.3 Simple Network Management Protocol Libraries (64-bit)
application SUNWsbuc Solstice Backup (Backup/Recover) Client
application SUNWsbum Solstice Backup (Backup/Recover) Man
application SUNWsbun Solstice Backup (Backup/Recover) Storage Node
application SUNWsbus1 Solstice Backup (Backup/Recover) Server
system SUNWsbus2 Solstice Backup (Backup/Recover) Device Drivers
under the server->registration, I found that the registration contains :-
Autochanger Module, 9 slots/9
ClientPaks for Windows/1
Networker for UNIX, Workgroup edition (8 clients per server)1 server
Networker Module for Oracl/1
BTW, inquire shows:-
/etc/LGTOuscsi/inquire
[email protected]:TOSHIBA DVD-ROM SD-M14011009|CD-ROM
[email protected]:ADIC FastStor 2 A12r|Autochanger (Jukebox)
[email protected]:HP Ultrium 1-SCSI E3 |Tape
[email protected]:HP Ultrium 1-SCSI E3 |Tape
where cfgadm -alv shows:-
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c0 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6:scsi
c0::/dev/lus connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM n /devices/pci@8,700000/scsi@6:scsi::/dev/lus
c0::dsk/c0t6d0 connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM y /devices/pci@8,700000/scsi@6:scsi::dsk/c0t6d0
c1 connected configured unknown
unavailable fc-private n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc
c1::21000004cfe34092 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34092
c1::21000004cfe34350 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34350
c2 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6,1:scsi
c2::lus1 connected configured unknown
unavailable unknown n /devices/pci@8,700000/scsi@6,1:scsi::lus1
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
c4 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@5:scsi
c4::lus3 connected configured unknown
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@5:scsi::lus3
usb0/1 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-kbd n /devices/pci@8,700000/usb@5,3:1
usb0/2 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:2
usb0/3 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-mouse n /devices/pci@8,700000/usb@5,3:3
usb0/4 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:4
nsrjb shows
Jukebox L8:
slot volume pool volume id recyclable
1: dwbak.inc.day0.wk0.001* 2481680129
2: dwbak.inc.day0.wk0.002 DW Incremental 2481704705 no
3: dwbak.inc.day0.wk0.003 DW Incremental 2481729793 no
4: -* -
5: dwbak.inc.day0.wk0.005 DW Incremental 2481779201 no
6: dwbak.inc.day0.wk0.006 DW Incremental 2481804289 no
7: dwbak.inc.day0.wk0.007 DW Incremental 2481829889 no
8: dwbak.inc.day0.wk0.008 DW Incremental 2481854209 no
*not registered in the NetWorker media data base
drive 1 (/dev/rmt/0cbn) slot 5: dwbak.inc.day0.wk0.005
nsrjb -HE hang indefinitly, so does nsrjb -HHE. devfsadm -c tape also hang while simply devfsadm can run without problem and cfgadm -alv c3 provide the following:-
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
nsjrb result should be past history, coz I am doing tar and manually changing the slot for quite some time already. Now I unconnect the cable and run devfsadm and then cfgadm -alv shows
cfgadm -alv
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c0 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6:scsi
c0::/dev/lus connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM n /devices/pci@8,700000/scsi@6:scsi::/dev/lus
c0::dsk/c0t6d0 connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM y /devices/pci@8,700000/scsi@6:scsi::dsk/c0t6d0
c1 connected configured unknown
unavailable fc-private n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc
c1::21000004cfe34092 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34092
c1::21000004cfe34350 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34350
c2 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6,1:scsi
c2::lus1 connected configured unknown
unavailable unknown n /devices/pci@8,700000/scsi@6,1:scsi::lus1
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
c4 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@5:scsi
c4::lus3 connected configured unknown
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@5:scsi::lus3
usb0/1 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-kbd n /devices/pci@8,700000/usb@5,3:1
usb0/2 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:2
usb0/3 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-mouse n /devices/pci@8,700000/usb@5,3:3
usb0/4 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:4
and inquire still shows
[email protected]:TOSHIBA DVD-ROM SD-M14011009|CD-ROM
[email protected]:ADIC FastStor 2 A12r|Autochanger (Jukebox)
[email protected]:HP Ultrium 1-SCSI E3 |Tape
[email protected]:HP Ultrium 1-SCSI E3 |Tape
and then I reconnect the cable I saw a lot of error message in dmesg:-
Jun 19 13:47:37 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:47:37 server Received unexpected SCSI Reset
Jun 19 13:47:37 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:47:37 server Received unexpected SCSI Reset
Jun 19 13:51:30 server scsi: [ID 107833 kern.notice] /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:30 server Failed to Get Features
Jun 19 13:51:50 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:50 server ISP: Firmware cmd timeout
Jun 19 13:51:50 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:50 server Fatal error, resetting interface, flg 1
and devfsadm hang. So I double check the past demsg and found a lot of similar SCSI error message as below:-
Jun 19 13:43:12 server probe request for LUN 0 denied: max LUN -1
Jun 19 13:43:12 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@5 (qus1):
Is that represent a hardware failure either on the jukebox or the SCSI controller? Or it is indeed a software corruption that can only be solved by reinstallation? But unfortunately I don't have the media on hand.
PS.a more details can be found under expert exchange thru the links below:-
http://www.experts-exchange.com/OS/Unix/Solaris/Q_23413012.html#a21749881
http://www.experts-exchange.com/OS/Unix/Solaris/Q_23478147.html

My company have a SUN Storedge L8 attached to a SUN Solaris 9 (SPARC) while I can only do a tar to the /dev/rmt/0, whenever I tried to interact with the jukebox with the solstice backup, the program hang definitely.
grep '/usr/kernel/drv/lus' /var/sadm/install/contents
/usr/kernel/drv/lus f none 0555 root bin 34624 12073 993189557 SUNWsbus2
/usr/kernel/drv/lus.conf f none 0444 root bin 3754 45438 993190441 SUNWsbus2
/usr/kernel/drv/lus32 f none 0555 root bin 33444 4422 993213667 SUNWsbus2
pkginfo -l SUNWsbus2
PKGINST: SUNWsbus2
NAME: Solstice Backup (Backup/Recover) Device Drivers
CATEGORY: system
ARCH: sparc
VERSION: 6.1,REV=Build.186
BASEDIR: /
VENDOR: Sun Microsystems, Inc.
PSTAMP: gelato010622054128
INSTDATE: Apr 08 2003 13:25
STATUS: completely installed
FILES: 48 installed pathnames
44 executables
37896 blocks used (approx)
this machine has installed the solstice backup manager
pkginfo | grep -i Solstice
system SUNWmibii Solstice Enterprise Agents 1.0.3 SNMP daemon
system SUNWsacom Solstice Enterprise Agents 1.0.3 files for root file system
system SUNWsadmi Solstice Enterprise Agents 1.0.3 Desktop Management Interface
system SUNWsadml Solstice Launcher.
system SUNWsadmx Solstice Enterprise Agents 1.0.3 Desktop Management Interface Libraries (64-bit)
system SUNWsasnm Solstice Enterprise Agents 1.0.3 Simple Network Management Protocol
system SUNWsasnx Solstice Enterprise Agents 1.0.3 Simple Network Management Protocol Libraries (64-bit)
application SUNWsbuc Solstice Backup (Backup/Recover) Client
application SUNWsbum Solstice Backup (Backup/Recover) Man
application SUNWsbun Solstice Backup (Backup/Recover) Storage Node
application SUNWsbus1 Solstice Backup (Backup/Recover) Server
system SUNWsbus2 Solstice Backup (Backup/Recover) Device Drivers
under the server->registration, I found that the registration contains :-
Autochanger Module, 9 slots/9
ClientPaks for Windows/1
Networker for UNIX, Workgroup edition (8 clients per server)1 server
Networker Module for Oracl/1
BTW, inquire shows:-
/etc/LGTOuscsi/inquire
[email protected]:TOSHIBA DVD-ROM SD-M14011009|CD-ROM
[email protected]:ADIC FastStor 2 A12r|Autochanger (Jukebox)
[email protected]:HP Ultrium 1-SCSI E3 |Tape
[email protected]:HP Ultrium 1-SCSI E3 |Tape
where cfgadm -alv shows:-
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c0 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6:scsi
c0::/dev/lus connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM n /devices/pci@8,700000/scsi@6:scsi::/dev/lus
c0::dsk/c0t6d0 connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM y /devices/pci@8,700000/scsi@6:scsi::dsk/c0t6d0
c1 connected configured unknown
unavailable fc-private n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc
c1::21000004cfe34092 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34092
c1::21000004cfe34350 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34350
c2 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6,1:scsi
c2::lus1 connected configured unknown
unavailable unknown n /devices/pci@8,700000/scsi@6,1:scsi::lus1
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
c4 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@5:scsi
c4::lus3 connected configured unknown
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@5:scsi::lus3
usb0/1 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-kbd n /devices/pci@8,700000/usb@5,3:1
usb0/2 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:2
usb0/3 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-mouse n /devices/pci@8,700000/usb@5,3:3
usb0/4 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:4
nsrjb shows
Jukebox L8:
slot volume pool volume id recyclable
1: dwbak.inc.day0.wk0.001* 2481680129
2: dwbak.inc.day0.wk0.002 DW Incremental 2481704705 no
3: dwbak.inc.day0.wk0.003 DW Incremental 2481729793 no
4: -* -
5: dwbak.inc.day0.wk0.005 DW Incremental 2481779201 no
6: dwbak.inc.day0.wk0.006 DW Incremental 2481804289 no
7: dwbak.inc.day0.wk0.007 DW Incremental 2481829889 no
8: dwbak.inc.day0.wk0.008 DW Incremental 2481854209 no
*not registered in the NetWorker media data base
drive 1 (/dev/rmt/0cbn) slot 5: dwbak.inc.day0.wk0.005
nsrjb -HE hang indefinitly, so does nsrjb -HHE. devfsadm -c tape also hang while simply devfsadm can run without problem and cfgadm -alv c3 provide the following:-
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
nsjrb result should be past history, coz I am doing tar and manually changing the slot for quite some time already. Now I unconnect the cable and run devfsadm and then cfgadm -alv shows
cfgadm -alv
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c0 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6:scsi
c0::/dev/lus connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM n /devices/pci@8,700000/scsi@6:scsi::/dev/lus
c0::dsk/c0t6d0 connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM y /devices/pci@8,700000/scsi@6:scsi::dsk/c0t6d0
c1 connected configured unknown
unavailable fc-private n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc
c1::21000004cfe34092 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34092
c1::21000004cfe34350 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34350
c2 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6,1:scsi
c2::lus1 connected configured unknown
unavailable unknown n /devices/pci@8,700000/scsi@6,1:scsi::lus1
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
c4 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@5:scsi
c4::lus3 connected configured unknown
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@5:scsi::lus3
usb0/1 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-kbd n /devices/pci@8,700000/usb@5,3:1
usb0/2 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:2
usb0/3 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-mouse n /devices/pci@8,700000/usb@5,3:3
usb0/4 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:4
and inquire still shows
[email protected]:TOSHIBA DVD-ROM SD-M14011009|CD-ROM
[email protected]:ADIC FastStor 2 A12r|Autochanger (Jukebox)
[email protected]:HP Ultrium 1-SCSI E3 |Tape
[email protected]:HP Ultrium 1-SCSI E3 |Tape
and then I reconnect the cable I saw a lot of error message in dmesg:-
Jun 19 13:47:37 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:47:37 server Received unexpected SCSI Reset
Jun 19 13:47:37 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:47:37 server Received unexpected SCSI Reset
Jun 19 13:51:30 server scsi: [ID 107833 kern.notice] /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:30 server Failed to Get Features
Jun 19 13:51:50 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:50 server ISP: Firmware cmd timeout
Jun 19 13:51:50 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:50 server Fatal error, resetting interface, flg 1
and devfsadm hang. So I double check the past demsg and found a lot of similar SCSI error message as below:-
Jun 19 13:43:12 server probe request for LUN 0 denied: max LUN -1
Jun 19 13:43:12 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@5 (qus1):
Is that represent a hardware failure either on the jukebox or the SCSI controller? Or it is indeed a software corruption that can only be solved by reinstallation? But unfortunately I don't have the media on hand.
PS.a more details can be found under expert exchange thru the links below:-
http://www.experts-exchange.com/OS/Unix/Solaris/Q_23413012.html#a21749881
http://www.experts-exchange.com/OS/Unix/Solaris/Q_23478147.html

Sun StorEdge 3510

Dears,
Good day,
I need your support to guide me to configure Sun StorEdge 3510. I have 24 Disks and single controller. I is connected to one host. I want to configure it with the most biggest storage. I want to implement RAID 5 on 11 disks on the first enclosure and the same to the second enclosure with two disks spare each one in the same enclosure.
Can you guide me throw this?
Thanks a lot.

Wow, it took me about 5 hours to set mine up from scratch and I'm a pretty strong storage guy. Here's an overview of what I did. Most of the info is in the 3510 documentation.
Step 1 is connectivity. Get your host to see the 3510 (FC).
Step 2 - use the cli utilities to setup the IP address on the controller (in-band).
Step 3 - ssh in, setup the RAID and presentation of the luns
Step 4 - rescan on the hosts to see the new luns

Solaris 8.0 on SUN SPARC 5 machine.

Can i install Solaris 8.0 on SUN SPARC 5 machines ?
Why can't i find it in the hardware compatibility list ?

Hi Solaris 8 is supported for Sparc Station 5 machines and should install just fine. However Solaris 8 is not supported on 4c architecture systems like the Sparc Station 1's and 2's...etc.
You can find a list of supported systems at the following URL:
http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-2221-10.pdf
Skip ahead to page 25 if you are looking just for supported machines.
Regards,
Andrew
Sun Developer Technical Support
Can i install Solaris 8.0 on SUN SPARC 5 machines ?
Why can't i find it in the hardware compatibility list

Sun StorEdge L8 Tape Library (UREGENT!!)

hi all
help needed.. i am new in this.. i ahve to do backup in the Sun StorEdge L8 every weekend.. as usual i will unload the Tape 1 and load the Tape 2 for this weekend backup.. Recently the tape shows '!' at the Tape 2.. when i try to unload the Tape 2, it shows me no tape is load.. wat does the '!' means?? can anyone explain? is it the tape is bad??
this is wat it shows when i mt staus
HP Ultrium LTO 2 tape drive:
sense key(0x6)= Unit Attention residual= 0 retries= 0
file no= 0 block no= 0
can anyone explain..
Thanks..

Hi Surajsid
Do you still have a support contract for this Library ? If it's still showing the same issues after power cycling the drive I would log a call with Orcale/Sun.
Have you changed anything in your backup environment lately ?
Regards
David

Maximum Disk-Volume Capacity Solaris 8 supports (SPARC) ?

Any one knows what is the maximum capacity that Solaris 8 on SPARC supports for storage-set ( Raid set, Stripe Set ...)
Can Solaris 8 supports file system up to 2 Terabyes ?
Thanks

Yup.
EOL in November 2002
Which means EOSL November 2007
http://sunsolve.sun.com/handbook_pub/validateUser.do?target=Systems/U10/U10
Unless you've somehow maintained a service contract on that system,
by specific system serial number,
your best bet is to haunt an online auction site (such as Ebay),
and get a replacement cpu or cpus for shelf stock.
Your current OBP patch level is only down two patch levels,
but your kernel patch level is essentially "never patched".
If it were patched better it may have noticed the issue a lot sooner.
Expect to replace that cpu.

Sun Storedge L9 command utility, need to load and unload tapes.

I am looking for a utility that will unload, and reload an L9 Sun storedge.
I found:
http://www.sun.com/bigadmin/jsp/descFile.jsp?url=descAll/l9ctl
This utility has some calls that either we don't have, or I can't find:
loadmedia.cgi
inloadmedia.cgi
Am I setting this up incorrectly?
Where is this stuff supposed to be?
I am running on a sun ulta-5, Solaris 8.

Hello!
Before use, You should small customize script:
1) Change
$LibraryHostName="http://l9"; - It's library hostname.
Or set this name in /etc/hosts
$AdminPwd="12341234"; - password to Library
And, of course, before use this script - you should setup netwotk connection of L9.
Another way - use project MTX.
http://freshmeat.net/projects/mtx/releases
This program use SCSI commands for control library.
Regards.

Is the Fujitsu-Solaris platform supported (ALL PRODUCTS)?

Is the Fujitsu-Solaris platform supported for Netscape/iPlanet products?
<P>
Quality assurance (QA) tests Netscape and iPlanet products (Solaris versions)
on Sun SPARC systems with the Solaris operating system from Sun Microsystems.
This setup is the reference platform.
<P>
If you run Netscape or iPlanet products on a SPARC/Solaris compatible system
(assuming the system is 100% compatible), the product should perform as
described. However, if you discover a compatibility problem on such a system,
Netscape/iPlanet Technical Support typically attempts to reproduce the defect
on the reference SPARC/Solaris platform. Then, if they find that the problem
exists on the reference platform, they will forward the defect on to
engineering for resolution.

Yes
We have plan to buy and use Aardvark OEM I2C Host Adapter and use it with LabView2013.
I am searching if this device already has LabView VI's for I2C communication.
I am not sure If we can use the VI's for Aardvark I2C/SPI Host Adapter to Aardvark OEM I2C Host Adapter.
Before we decide to buy Aardvark OEM I2C Host Adapter we just want to make sure that we can use it.
Best Thanks.
Jessie

Sun Storedge 3310

I would like to know if it is possible to connect a sun storedge 3310 array to windows server 2012 r2? If ther is could you tell me how. I know how to do it on server 2003 but 2012 r2 is much different.

Hi,
I would like to know if it is possible to connect a sun storedge 3310 array to windows server 2012 r2?
Since we are not familiar with the product you have mentioned, I would suggest you contact corresponding vendor support to get more specific and accurate response.
Thank you for your understanding and support.
Best Regards,
Amy
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Import netscape.ldap.* ; is it not supported in Sun one LDAP server

import netscape.ldap.*;
is the above line not supported n Sun One LDAP directory Server
if that is the case what should i do
wenever i compile my code the error tat comes up is : package netscap.ladp does not exists
need help immediately
my code is as follows
import netscape.ldap.*;
import java.util.*;
* Simple search program to experiment with filters
public class SearchFilter {
* Do a subtree search using a specified filter
* @parm args host, port, authDN, password, baseDN, filter
public static void main(String[] args) {
if (args.length != 6) {
System.out.println("Usage: java FilterSearch " + "<host> <port> " + "<authdn> <password> " + "<baseDN> <filter>");
System.out.println("Example:");
System.out.println(" java FilterSearch " + "localhost 389 " + "\"\" \"\" " + "\"o=airius.com\" " + "\"(|(cn=sam*)(cn=b*))\"");
System.exit(1);
}

Couldn't you download the netscape.ldap package (iPlanet LDAP SDK) and put its jars in your app classpath?
The suggested way to replace netscape.ldap package is to use only JNDI calls, but maybe they can not fulfill all your needs.
By the way, you can get the source code for that package in Mozilla.org site.
(Note: if you are using Netscape LDAP SDK for parsing/generating ASN.1 streams including X.509 certificates, try using BouncyCastle instead of netscape.ldap.ber.stream package - I had to modify several classes from Netscape's package that is not meant to handle certificates, but LDAP streams...)

How to integrate a Solaris x86 server on Sun Management Center ?

Hello people,
I want to integrate a Solaris x86 server on Sun Management Center platform.
If I'm not wrong, SunMC doesn't run for Solaris x86, server and client only as console with Java.
In speat of it, I try to install Sun Management Center 3.0 Agent for Solaris x86.
It seems to be ok, install packages, but when execute es-setup script, intents to create the following directory:
/opt/SUNWsymon/base/bin/sparc-sun-solaris2.8
I supose that in this directory, SunMC will install sparc binary files
At this point, I can't follow the installation and abort it.
Can anybody give me ideas to install and integrate my solaris x86 server on SunMC ?
Thanks

Hi Hisham,
hishooooo wrote:
Dear Gents,
I have one X86 Solaris Server configured and installed to be Sun Management Center Server.
successfully i could monitor the Sun Solaris Servers after i have installed the SMC agent on them.
my problem is that i could not install the SMC agent on Red Hat Linux. as i could not find an easy document or steps to do so.
could you guide please?If you still have a copy of your SunMC media around, the same ["es-inst"|http://docs.sun.com/app/docs/doc/820-2215/command-line-1?l=en&a=view] program you use to install Solaris Agents should work on Linux as well. It autodetects OS type and will install Solaris packages or RPMs as appropriate.
Regards,
[email protected]
http://www.HalcyonInc.com

How to integrate Solaris x86 server on Sun Management Center ?

Hello people,
I want to integrate a Solaris x86 server on Sun Management Center platform.
If I'm not wrong, SunMC doesn't run for Solaris x86, server and client only as console with Java.
In speat of it, I try to install Sun Management Center 3.0 Agent for Solaris x86.
It seems to be ok, install packages, but when execute es-setup script, intents to create the following directory:
/opt/SUNWsymon/base/bin/sparc-sun-solaris2.8
I supose that in this directory, SunMC will install sparc binary files
At this point, I can't follow the installation and abort it.
Can anybody give me ideas to install and integrate my solaris x86 server on SunMC ?
Thanks

Hi
From the Unix prompt enter oemapp console(for v9.x). If you are using earlier versions it is oemapp console (for starting the console) and oemapp dbastudio(for starting dba studio)
For starting OMS enter: oemctrl start oms.
Hope this helps
sarath

Solaris 8 support for CMD-649

Does Solaris 8 support the CMD-649 PCI to IDE device?
dp

Currently Solaris 10 is not supported in CSA 5 or the upcoming CSA 6. I am told that they will be adding Solaris 10 for CSA 6 but it is unknown as to when this will be released.

Solaris 10 support on Sun Storedge 6120/6020

Similar Messages

Maybe you are looking for