[SOLVED] Jmicron ethernet card doesn't work
HI there,
I am installing Arch64 on Sager NP8170 laptop. Networking card is Jmicron PCI Express Gigabit Ethernet Adapter, which is controlled by kernel-build module JME.
Command
lsmod | grep jme
shows that module is loaded. Ping to sites does not work.
dhcpcd eth0
is timed out.
I loaded the latest module from www.jmicron.com. The driver is compiled by the following Makefile:
MODNAME := jme
TEMPFILES := $(MODNAME).o $(MODNAME).mod.c $(MODNAME).mod.o Module.symvers .$(MODNAME).*.cmd .tmp_versions modules.order
EXTRA_CFLAGS += -Wall -O3
#EXTRA_CFLAGS += -DTX_DEBUG
#EXTRA_CFLAGS += -DREG_DEBUG
obj-m := $(MODNAME).o
ifeq (,$(BUILD_KERNEL))
BUILD_KERNEL=$(shell uname -r)
endif
KSRC ?= /lib/modules/$(BUILD_KERNEL)/build
MODULE_INSTALLDIR = /lib/modules/$(BUILD_KERNEL)/kernel/drivers/net
all:
@$(MAKE) -C $(KSRC) SUBDIRS=$(shell pwd) modules
@rm -rf $(TEMPFILES)
checkstack:
$(MAKE) -C $(KSRC) SUBDIRS=$(shell pwd) modules
objdump -d $(obj-m) | perl $(KSRC)/scripts/checkstack.pl i386
@rm -rf $(TEMPFILES)
namespacecheck:
$(MAKE) -C $(KSRC) SUBDIRS=$(shell pwd) modules
perl $(KSRC)/scripts/namespace.pl
@rm -rf $(TEMPFILES)
clean:
@rm -rf $(MODNAME).ko $(TEMPFILES)
install: all
install -c -m 644 *.ko $(MODULE_INSTALLDIR)
/sbin/depmod -ae
When I am doing
make install
I have the following error:
make: *** /lib/modules/2.6.33-ARCH/build : No such file or directory. Stop
I am working with the problem for 2 days and googling does not help either.
Please help.
Last edited by Fixed (2011-05-24 15:45:03)
Here are the replies to the commands:
ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:90:F5:B8:10:8A
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:31
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
#dmesg | tail -50
usb 1-1: new high speed USB device using ehci_hcd and address 2
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: irq 30 for MSI/MSI-X
HDA Intel 0000:00:1b.0: setting latency timer to 64
firewire_core: created device fw0: GUID ea6410b8f5900058, S400
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
hda_codec: ALC892: BIOS auto-probing.
Too many connections
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input8
Too many connections
usb 3-1: new high speed USB device using ehci_hcd and address 2
Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04731/0xa40000
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input9
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 8 ports detected
EXT3-fs (sdb1): using internal journal
usb 3-1.1: new full speed USB device using ehci_hcd and address 3
usb 3-1.5: new full speed USB device using ehci_hcd and address 4
usbcore: registered new interface driver hiddev
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb3/3-1/3-1.1/3-1.1:1.0/input/input10
generic-usb 0003:046D:C52B.0001: input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.0-1.1/input0
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb3/3-1/3-1.1/3-1.1:1.1/input/input11
generic-usb 0003:046D:C52B.0002: input,hiddev0,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1.1/input1
generic-usb 0003:046D:C52B.0003: hiddev1,hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-1.1/input2
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usb 3-1.6: new high speed USB device using ehci_hcd and address 5
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device BisonCam, NB Pro (5986:0343)
input: BisonCam, NB Pro as /devices/pci0000:00/0000:00:1d.0/usb3/3-1/3-1.6/3-1.6:1.0/input/input12
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
jme 0000:03:00.0: irq 31 for MSI/MSI-X
eth0: Link is down.
usb 3-1.2: new high speed USB device using ehci_hcd and address 6
Initializing USB Mass Storage driver...
scsi6 : usb-storage 3-1.2:1.0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 6:0:0:0: Direct-Access HP v125w PMAP PQ: 0 ANSI: 0 CCS
sd 6:0:0:0: Attached scsi generic sg3 type 0
sd 6:0:0:0: [sdc] 15667200 512-byte logical blocks: (8.02 GB/7.47 GiB)
sd 6:0:0:0: [sdc] Write Protect is off
sd 6:0:0:0: [sdc] Mode Sense: 23 00 00 00
sd 6:0:0:0: [sdc] Assuming drive cache: write through
sd 6:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
sd 6:0:0:0: [sdc] Assuming drive cache: write through
sd 6:0:0:0: [sdc] Attached SCSI removable disk
#ip link
command not found
#lspci -vvv
00:00.0 Host bridge: Intel Corporation Device 0104 (rev 09)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:01.0 PCI bridge: Intel Corporation Device 0101 (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f4000000-f60fffff
Prefetchable memory behind bridge: 00000000e8000000-00000000f3ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: CLEVO/KAPOK Computer Device 7100
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4169
Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [140 v1] Root Complex Link
Desc: PortNumber=02 ComponentID=01 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed19000
Kernel driver in use: pcieport
Kernel modules: shpchp
00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f650a000 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI])
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6508000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 30
Region 0: Memory at f6500000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000feeff00c Data: 41a9
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=22
Status: NegoPending- InProgress-
Capabilities: [130 v1] Root Complex Link
Desc: PortNumber=0f ComponentID=00 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c000
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f6400000-f64fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #0, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4171
Capabilities: [90] Subsystem: CLEVO/KAPOK Computer Device 7100
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f6300000-f63fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4179
Capabilities: [90] Subsystem: CLEVO/KAPOK Computer Device 7100
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.2 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 3 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f6200000-f62fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #3, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #2, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4181
Capabilities: [90] Subsystem: CLEVO/KAPOK Computer Device 7100
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 4 (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f6100000-f61fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #4, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #3, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4189
Capabilities: [90] Subsystem: CLEVO/KAPOK Computer Device 7100
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI])
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f6507000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1f.0 ISA bridge: Intel Corporation Device 1c4b (rev 05)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
Kernel modules: iTCO_wdt
00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 29
Region 0: I/O ports at f070 [size=8]
Region 1: I/O ports at f060 [size=4]
Region 2: I/O ports at f050 [size=8]
Region 3: I/O ports at f040 [size=4]
Region 4: I/O ports at f020 [size=32]
Region 5: Memory at f6506000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 4191
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f6505000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f000 [size=32]
Kernel modules: i2c-i801
01:00.0 VGA compatible controller: nVidia Corporation Device 0dd1 (rev a1) (prog-if 00 [VGA controller])
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e8000000 (64-bit, prefetchable) [size=128M]
Region 3: Memory at f0000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at e000 [size=128]
Expansion ROM at f6000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <512ns, L1 <4us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [b4] Vendor Specific Information: Len=14 <?>
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [128 v1] Power Budgeting <?>
Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Kernel modules: nvidiafb
01:00.1 Audio device: nVidia Corporation Device 0be9 (rev a1)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at f6080000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <512ns, L1 <4us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
02:00.0 USB Controller: NEC Corporation Device 0194 (rev 03) (prog-if 30)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6400000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [90] MSI-X: Enable- Count=8 Masked-
Vector table: BAR=0 offset=00001000
PBA: BAR=0 offset=00001080
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 unlimited
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
Capabilities: [150 v1] #18
Kernel driver in use: xhci_hcd
Kernel modules: xhci
03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 31
Region 0: Memory at f6320000 (32-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at d100 [size=128]
Region 3: I/O ports at d000 [size=256]
Region 4: Memory at f6310000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at f6300000 [disabled] [size=64K]
Capabilities: [68] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [40] MSI-X: Enable- Count=8 Masked-
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [70] MSI: Enable+ Count=1/8 Maskable+ 64bit+
Address: 00000000feeff00c Data: 41b1
Masking: 000000fe Pending: 00000000
Capabilities: [100 v1] Device Serial Number 8a-10-b8-ff-ff-f5-90-00
Kernel driver in use: jme
Kernel modules: jme
03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 4
Region 0: Memory at f6326000 (32-bit, non-prefetchable) [size=256]
Capabilities: [a4] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [100 v1] Device Serial Number 8a-10-b8-ff-ff-f5-90-00
03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) (prog-if 01)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 18
Region 0: Memory at f6325000 (32-bit, non-prefetchable) [size=256]
Capabilities: [a4] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: fffffffc Data: 0000
Capabilities: [100 v1] Device Serial Number 8a-10-b8-ff-ff-f5-90-00
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90)
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 4
Region 0: Memory at f6324000 (32-bit, non-prefetchable) [size=256]
Capabilities: [a4] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: fffffffc Data: 0000
Capabilities: [100 v1] Device Serial Number 8a-10-b8-ff-ff-f5-90-00
04:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8176 (rev 01)
Subsystem: Realtek Semiconductor Co., Ltd. Device 9196
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 4
Region 0: I/O ports at c000 [size=256]
Region 2: Memory at f6200000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 01-91-81-fe-ff-4c-e0-00
05:00.0 FireWire (IEEE 1394): JMicron Technology Corp. IEEE 1394 Host Controller (rev 30) (prog-if 10 [OHCI])
Subsystem: CLEVO/KAPOK Computer Device 7100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f6101000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at f6100000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [94] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: fffffffc Data: 0000
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci
Similar Messages
-
Ethernet card doesn't work with new arch install?
Hi guys,
so this is kinda my first post, not that I'm new to arch i just never had an issue i couldn't figure out on my own... But i love arch i have been using it for about a year now and have had no serious problems except for this. I have had arch running on an older dell vostro 200 desktop before i reinstalled with a vary similar issue except that the fix i came up with doesn't work anymore. I will tell you about the first issue first because i ALMOST posted on here about it originally but i figured out a way to make it work even though it was a hassle.
After cold/rebooting my computer the network card doesn't work at all. lspci reported that the kernel module e1000e was the correct one (i have verified this) and that the kernel has loaded it, i verified that with dmesg but still it wouldn't work. After much much anguish and hairpulling, I realized that it had to have something to do with the module so i tried forcing it to reload with rmmod e1000e and modprobe e1000e and it still wouldn't work until i physically unpluged the ethernet cord and pluged it back in until the light on the NIC turned on. After that everything works as normal i could even unplug and plug it back in with no problems. So eventually i wrote a script that did this for me (except for the uplugging and plugging part) and i used that when i cold/rebooted.
But now i have the exact same issue after reinstalling arch to the T except for the fact that the (crazy) fix i came up with doesn't work now. I used my "fix" after booting from the arch cd and it worked just like it always has. And now after rebooting into my fresh system the fix doesn't work anymore. So now i'm back where i was to begin with but i have no idea what to try next. I didn't do anything particularly different during installation except i added a udev rule for the e1000e module just to see if somehow that would fix the problem... it didnt and i have since deleted that (to see if it was the problem). The only other thing that is different is the root and home are now btrfs partitions instead of ext4.
I have booted several other live cds and dvds (diferent distros) including arch derivatives such as manjaro and they all worked just fine, using the same kernel module (e1000e). I'm not sure what that could mean but i know that it means there is a fix for this some way or another. I am going to hook up a wifi adapter and connect that computer to the internet to put some more information up if it's needed (asked for) but for now lspci -vnn | grep -i -A 10 net reports
00:19.0 Ethernet controller [0200]: Intel Corporation 82562V-2 10/100 Network Connection [8086:10c0] (rev 02)
Subsystem: Dell Device 0238
Flags: bus master, fast devsel, latency 0, IRQ 42
Memory at fdfc0000 (32-bit non-prefetchable) [size=128k]
Memory at fdfff000 (32-bit non-prefetchable) [size=4k]
I/0 ports at ff00 [size=32]
Capabilities: [c8] Power Management version 2
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [e0] Vendor Specific Information: Len=06 <?>
Kernel driver in use: e1000e
Kernel modules: e1000e
ip a reports:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
3: enp0s25: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:1d:09:8c:36:f6 brd ff:ff:ff:ff:ff:ff
4: wlp0s29f7u3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 64:66:b3:16:92:10 brd ff:ff:ff:ff:ff:ff
inet 172.16.1.55/16 brd 172.16.255.255 scope global wlp0s29f7u3
valid_lft forever preferred_lft forever
inet6 fe80::6666:b3ff:fe16:9210/64 scope link
valid_lft forever preferred_lft forever
lsmod | grep e1000e
e1000e 215644 0
ptp 17692 1 e1000e
any help on what to do next would be greatly appreciated.
Last edited by mvheart/dev/null (2014-08-18 04:02:12)Sorry I was thinking that it was say "state up" after that, I was looking in the wrong place... It's been a long time since I was playing around with this. So it is as i thought it was before?
[aaron@arch-box Arch-Linux]$ sudo systemctl start [email protected]
[sudo] password for aaron:
Job for [email protected] failed. See 'systemctl status [email protected]' and 'journalctl -xn' for details.
[aaron@arch-box Arch-Linux]$ systemctl status -l [email protected]
● [email protected] - dhcpcd on enp0s25
Loaded: loaded (/usr/lib/systemd/system/[email protected]; disabled)
Active: failed (Result: exit-code) since Mon 2014-08-18 11:20:29 EDT; 4min 11s ago
Process: 17650 ExecStart=/usr/bin/dhcpcd -q -w %I (code=exited, status=1/FAILURE)
Aug 18 11:19:59 arch-box dhcpcd[17650]: version 6.4.3 starting
Aug 18 11:19:59 arch-box dhcpcd[17650]: enp0s25: adding address fe80::ae3:ee04:7099:77c5
Aug 18 11:19:59 arch-box systemd[1]: Starting dhcpcd on enp0s25...
Aug 18 11:19:59 arch-box dhcpcd[17650]: enp0s25: waiting for carrier
Aug 18 11:20:29 arch-box systemd[1]: [email protected]: control process exited, code=exited status=1
Aug 18 11:20:29 arch-box systemd[1]: Failed to start dhcpcd on enp0s25.
Aug 18 11:20:29 arch-box systemd[1]: Unit [email protected] entered failed state.
Last edited by mvheart/dev/null (2014-08-18 15:50:10) -
P20-552: 2GB SD card doesn't work.
I have a P20-552 (PSP26E-025E9-S4) which is about 18 months old. I recently bought a Canon digital camera (IxUS 750) with a 2GB Sandisk Ultra II SD card and the combination is working well. Although I can transfer images from the camera to my Toshiba portable using an USB cable, sometimes I would like to use the SD slot on the portable but there seems to be a problem: seconds after pressing home the SD card in the slot I get the message "Disk is not formatted - Do you want to format it now?". I reply OK but then I get the message "The disk in drive E cannot be formatted"
The card continues to work perfectly well in both my camera and in my iPaq PocketPC. The SD card slot in the Toshiba will work quite happily with the Sandisk 256MB SD card that is usually in my PDA.
Anybody has any idea why the 2GB card doesn't work in the Toshiba? Is it a question of updating a driver - I did look the other day but I couldn't find anything that to me seemed appropriate but I might well have overlooked something..
I am running XP Home (SP2) and have fully automatic updates ON. I have Norton Virus and Zone Alarm running and am not experiencing any problems with any other software/applications - at least, no problem since someone suggested vacuuming my overheating laptop a few weeks ago ;-)
Thanks, Brian.It seems that the unit doesnt support this card.
Check your user manual. There you will find a information that this unit supports only the following SD card sizes: 8/16/32/64/128/256 and 512 MB
According to this document the 2 GB are to high. -
Hi. Unfortunately my ethernet card was not working anymore. This is the message "This computer does not appear to have any PCI Ethernet card. How can I fix it?
i would try an SMC reset, the following article tells how to do this:
http://support.apple.com/kb/HT3964
if it still gives that message, you need to take it to apple store or apple service provider to have a new card installed. the apple site gives listings of providers and stores in your area:
https://locate.apple.com -
How do I turn this off? I can't download anything until I put in the card's information. But the card doesn't work anymore, it ran out of money. It keeps saying that my last perchase was unseccessful or something. I just want this to stop so I can update and download apps! Please help!
My iMac with Snow Leopard 10.6.8 crahed b/c the HD cannot be repaired. I reinstalled Mac OS X and luckily have most documents and applications. I have moved them all into folders before I erase the HD. I had all my documents but lost the 3 applications for iWorks. It says go to the store, buy and enter your serial#. That is not working. Here it is:MB966Z/A
WVL 001299 10959191-000
I need the updates. Apple has my sign in Apple ID.
Thanks,
pandaposyus -
What do you do went your iTunes redeem card doesn't work ?, What do you do went your iTunes redeem card doesn't work ?
Welcome to the Apple Community.
The following article(s) may help you.
iTunes Card and Gift Certificate FAQ -
Why my nano cut sim card doesn't work on iphone 5c?
why my nano cut sim card doesn't work on iphone 5c?
Cut cards often don't work. Get a real nano SIM from your cell carrier.
Regards. -
IPhone 5 sim card doesn't work
Hi,
One day the SIM card in IPhone 5 just stopped working. I can see the network on the desktop and in general settings, but it does not work for real. I can't make a call, send a message or get internet. Sometimes it goes "No service", "Searching" but then goes back.
I have checked this SIM card with different phone - it works properly good. Any different SIM card in my IPhone also doesn't work.
So I went to the Apple Store (Indonesia, Denpasar, Bali) they said you need to reset all the content and settings. So I did all and nothing happened.
Again SIM doesn't work - same situation. What is interesting sometimes I'm getting messages from the network so it seems that SIM card works some time but I can not make any calls or actions with SIM.
In the App Store guys told me this might be a hardware problem which could not be solved it's just broken.
They say you can exchange an IPhone for the new one but not in Bali because they don't have IPhone 5 anymore. Is it fair?
Please help me what can I do and how can I make my IPhone works or exchanged it for a new one.
I will be in Malaysia, Kuala Lumpur on February 7th. Can I exchange my IPhone here?
Version 7.1.1 (11D201)
was bought in USA 2,5 years ago
I live in Bali, Indonesia
Thank you in advance for any help.
Best regards,
YuliaThank you. I bought IPhone in USA 2 years ago.
"The iPhone warranty is not international" - it's very sad. Just wondering why people in the Store told me different things. -
Hello, I've just upgraded to linux-firmware and the newest X.org, which doesn't work.
Xorg.0.log tells me:
[ 934.318]
X.Org X Server 1.8.1
Release Date: 2010-05-11
[ 934.322] X Protocol Version 11, Revision 0
[ 934.323] Build Operating System: Linux 2.6.33-ARCH x86_64
[ 934.325] Current Operating System: Linux staerseus 2.6.34-ARCH #1 SMP PREEMPT Sat Jun 19 00:07:49 CEST 2010 x86_64
[ 934.326] Kernel command line: root=/dev/disk/by-uuid/727c4683-ee4c-4b32-8a59-370264cb7d9f ro i915.modeset=1 init=/sbin/bootchartd
[ 934.327] Build Date: 26 May 2010 07:50:07PM
[ 934.329]
[ 934.330] Current version of pixman: 0.18.2
[ 934.331] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 934.334] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 934.338] (==) Log file: "/var/log/Xorg.0.log", Time: Mon Jun 21 10:15:38 2010
[ 934.340] (==) Using config file: "/etc/X11/xorg.conf"
[ 934.341] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 934.343] (==) No Layout section. Using the first Screen section.
[ 934.343] (==) No screen section available. Using defaults.
[ 934.343] (**) |-->Screen "Default Screen Section" (0)
[ 934.343] (**) | |-->Monitor "<default monitor>"
[ 934.343] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 934.343] (==) Automatically adding devices
[ 934.343] (==) Automatically enabling devices
[ 934.343] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 934.343] Entry deleted from font path.
[ 934.343] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/,
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/
[ 934.343] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 934.343] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 934.343] (II) Loader magic: 0x7ce880
[ 934.343] (II) Module ABI versions:
[ 934.343] X.Org ANSI C Emulation: 0.4
[ 934.343] X.Org Video Driver: 7.0
[ 934.343] X.Org XInput driver : 9.0
[ 934.343] X.Org Server Extension : 3.0
[ 934.352] (--) PCI:*(0:0:2:0) 8086:2a42:1734:113f Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller rev 7, Mem @ 0xf2400000/4194304, 0xd0000000/268435456, I/O @ 0x00001800/8
[ 934.352] (--) PCI: (0:0:2:1) 8086:2a43:1734:113f Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller rev 7, Mem @ 0xf2100000/1048576
[ 934.352] (II) Open ACPI successful (/var/run/acpid.socket)
[ 934.352] (II) LoadModule: "extmod"
[ 934.352] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 934.352] (II) Module extmod: vendor="X.Org Foundation"
[ 934.352] compiled for 1.8.1, module version = 1.0.0
[ 934.352] Module class: X.Org Server Extension
[ 934.352] ABI class: X.Org Server Extension, version 3.0
[ 934.352] (II) Loading extension MIT-SCREEN-SAVER
[ 934.352] (II) Loading extension XFree86-VidModeExtension
[ 934.352] (II) Loading extension XFree86-DGA
[ 934.352] (II) Loading extension DPMS
[ 934.352] (II) Loading extension XVideo
[ 934.352] (II) Loading extension XVideo-MotionCompensation
[ 934.352] (II) Loading extension X-Resource
[ 934.352] (II) LoadModule: "dbe"
[ 934.352] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 934.352] (II) Module dbe: vendor="X.Org Foundation"
[ 934.353] compiled for 1.8.1, module version = 1.0.0
[ 934.353] Module class: X.Org Server Extension
[ 934.353] ABI class: X.Org Server Extension, version 3.0
[ 934.353] (II) Loading extension DOUBLE-BUFFER
[ 934.353] (II) LoadModule: "glx"
[ 934.353] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 934.353] (II) Module glx: vendor="X.Org Foundation"
[ 934.353] compiled for 1.8.1, module version = 1.0.0
[ 934.353] ABI class: X.Org Server Extension, version 3.0
[ 934.353] (==) AIGLX enabled
[ 934.353] (II) Loading extension GLX
[ 934.353] (II) LoadModule: "record"
[ 934.353] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 934.353] (II) Module record: vendor="X.Org Foundation"
[ 934.353] compiled for 1.8.1, module version = 1.13.0
[ 934.353] Module class: X.Org Server Extension
[ 934.353] ABI class: X.Org Server Extension, version 3.0
[ 934.353] (II) Loading extension RECORD
[ 934.353] (II) LoadModule: "dri"
[ 934.353] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 934.353] (II) Module dri: vendor="X.Org Foundation"
[ 934.353] compiled for 1.8.1, module version = 1.0.0
[ 934.353] ABI class: X.Org Server Extension, version 3.0
[ 934.353] (II) Loading extension XFree86-DRI
[ 934.354] (II) LoadModule: "dri2"
[ 934.354] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 934.354] (II) Module dri2: vendor="X.Org Foundation"
[ 934.354] compiled for 1.8.1, module version = 1.2.0
[ 934.354] ABI class: X.Org Server Extension, version 3.0
[ 934.354] (II) Loading extension DRI2
[ 934.354] (==) Matched intel as autoconfigured driver 0
[ 934.354] (==) Matched vesa as autoconfigured driver 1
[ 934.354] (==) Matched fbdev as autoconfigured driver 2
[ 934.354] (==) Assigned the driver to the xf86ConfigLayout
[ 934.354] (II) LoadModule: "intel"
[ 934.354] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 934.354] (II) Module intel: vendor="X.Org Foundation"
[ 934.354] compiled for 1.7.6, module version = 2.11.0
[ 934.354] Module class: X.Org Video Driver
[ 934.354] ABI class: X.Org Video Driver, version 6.0
[ 934.354] (EE) module ABI major version (6) doesn't match the server's version (7)
[ 934.356] (II) UnloadModule: "intel"
[ 934.356] (II) Unloading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 934.356] (EE) Failed to load module "intel" (module requirement mismatch, 0)
[ 934.357] (II) LoadModule: "vesa"
[ 934.357] (WW) Warning, couldn't open module vesa
[ 934.357] (II) UnloadModule: "vesa"
[ 934.357] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 934.359] (II) LoadModule: "fbdev"
[ 934.359] (WW) Warning, couldn't open module fbdev
[ 934.359] (II) UnloadModule: "fbdev"
[ 934.359] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 934.360] (EE) No drivers available.
[ 934.362]
Fatal server error:
[ 934.364] no screens found
[ 934.365]
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 934.370] Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 934.372]
What does the problem with modules mean? Archlinux was warning me, that "in future releases /etc/modprobe.d/framebuffer_blacklist.conf.save will be ignored, but it is the same file as /etc/modprobe.d/framebuffer_blacklist.conf.
I don't understand, why it cannot find any screens (I use a laptop screen)
I tried to start with and without xorg.conf, which is:
Section "Device"
Identifier "Intel X4500MHD"
Driver "intel"
VendorName "Intel Corporation"
BoardName "Mobile 4 Series Chipset Integrated Graphics Controller"
BusID "PCI:0:2:0"
Option "DRI" "true"
Option "AccelMethod" "uxa"
Option "MigrationHeuristic" "greedy"
EndSection
The graphic driver I use is xf86-video-intel-newest from archstuff, but it is the same version as xf86-video-intel.
I am not sure if I provided all needed info, but I hope so. Thank you for your help.SOLVED
Last edited by Staerseus (2010-06-21 09:18:03)Use the arch version. It is actually built against the xorg version that you are using... here is the relevant section of your log:
[ 934.354] (EE) module ABI major version (6) doesn't match the server's version (7) -
ICloud is messing with my phone and now iStore says my card doesn't work.
Okay. Where do I begin. I feel like a crazy person, Anyway.
So all of this started when I got my MacBook Pro. I had just got a new e-mail so of course I want to update my iCloud account with the new e-mail and a new password. Seems easy enough but NO, it's been a nightmare.
1. I can't update, delete or do anything with the iCloud setting in my phone, which is still registered to the old e-mail. It keeps asking for the old password and it does not make sense because it has been disabled. Help me god.
2. I can't update or do anything in the App/iTunes Store because it keeps asking for verification, which leads to my card info (was already saved) but now all I get is it has either been declined or is not a valid payment option etc etc etc.
3. Same thing as number 2 happened on my iTunes Store on my macbook.
And that's it. My phone is having a meltdown because he's stuck in some sort of non-existant iCloud account twilight zone. I've tried everything and nothing seems to work, I get nothing from the apple support (thanks Apple! Great customer care by the way!) and no one around me seems to know what to do or what the deal is.
I'm just a simple human being that gets very frustrated when technology doesn't work.
So if anyone out there is really smart and can figure this out and tell me step by step what to do before I set my phone on fire, please help me!
I'd really appreciate it. Thanks!Does your phone charge without issues when using the Apple supplied charger?
If it does, the issue is with the Mophie.
If it does not, the issue may be with the iPhone or may simply be a dirty dock connector. -
[SOLVED] External USB mouse doesn't work
I've installed Arch on my laptop and today faced with a problem. When I boot with AC off my external USB mouse doesn't work. Also it looks like USB ports don't work. If I detached AC when working mouse works fine.
I can suppose there is some problem with laptop mode. May be it turns off usb ports to save energy. Anyway quick search doesn't brings any results. If someone give me a hint how to solve this problem I'll be very grateful.
Last edited by avli (2011-07-14 16:53:15)Well, after diving into configs solution has been founded. The point was to disable auto suspend feature in laptop-mode-tools config by setting BATT_SUSPEND_USB variable to 0 in /etc/laptop-mode/conf.d/usb-autosuspend.conf
Hope this information will be helpful for users who probably faced with the same problem. Thank you! -
[solved] remove grub timeout doesn't work
i am trying to remove the grub timeout by editing /etc/default/grub and setting grub_timeout to 0, but it doesn't work, is there anything else i should change?
p.s. should i run grub-mkconfig?
Last edited by aldoiljazi (2013-09-18 07:35:11)okay i run 'sudo grub-mkconfig'
this is my /etc/default/grub
GRUB_DEFAULT=0
GRUB_TIMEOUT=0
GRUB_DISTRIBUTOR="Arch"
GRUB_CMDLINE_LINUX_DEFAULT="quiet"
GRUB_CMDLINE_LINUX=""
# Preload both GPT and MBR modules so that they are not missed
GRUB_PRELOAD_MODULES="part_gpt part_msdos"
# Uncomment to enable Hidden Menu, and optionally hide the timeout count
#GRUB_HIDDEN_TIMEOUT=5
#GRUB_HIDDEN_TIMEOUT_QUIET=true
# Uncomment to use basic console
GRUB_TERMINAL_INPUT=console
# Uncomment to disable graphical terminal
#GRUB_TERMINAL_OUTPUT=console
# The resolution used on graphical terminal
# note that you can use only modes which your graphic card supports via VBE
# you can see them in real GRUB with the command `vbeinfo'
GRUB_GFXMODE=auto
# Uncomment to allow the kernel use the same resolution used by grub
GRUB_GFXPAYLOAD_LINUX=keep
# Uncomment if you want GRUB to pass to the Linux kernel the old parameter
# format "root=/dev/xxx" instead of "root=/dev/disk/by-uuid/xxx"
#GRUB_DISABLE_LINUX_UUID=true
# Uncomment to disable generation of recovery mode menu entries
GRUB_DISABLE_RECOVERY=true
# Uncomment and set to the desired menu colors. Used by normal and wallpaper
# modes only. Entries specified as foreground/background.
#GRUB_COLOR_NORMAL="light-blue/black"
#GRUB_COLOR_HIGHLIGHT="light-cyan/blue"
# Uncomment one of them for the gfx desired, a image background or a gfxtheme
#GRUB_BACKGROUND="/path/to/wallpaper"
#GRUB_THEME="/path/to/gfxtheme"
# Uncomment to get a beep at GRUB start
#GRUB_INIT_TUNE="480 440 1"
#GRUB_SAVEDEFAULT="true"
and this is my /boot/grub/grub.cfg
# DO NOT EDIT THIS FILE
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
### BEGIN /etc/grub.d/00_header ###
insmod part_gpt
insmod part_msdos
if [ -s $prefix/grubenv ]; then
load_env
fi
if [ "${next_entry}" ] ; then
set default="${next_entry}"
set next_entry=
save_env next_entry
set boot_once=true
else
set default="0"
fi
if [ x"${feature_menuentry_id}" = xy ]; then
menuentry_id_option="--id"
else
menuentry_id_option=""
fi
export menuentry_id_option
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
function load_video {
if [ x$feature_all_video_module = xy ]; then
insmod all_video
else
insmod efi_gop
insmod efi_uga
insmod ieee1275_fb
insmod vbe
insmod vga
insmod video_bochs
insmod video_cirrus
fi
if [ x$feature_default_font_path = xy ] ; then
font=unicode
else
insmod part_msdos
insmod ext2
set root='hd0,msdos1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 6b44daaa-610c-4f23-a632-569d091e4d43
else
search --no-floppy --fs-uuid --set=root 6b44daaa-610c-4f23-a632-569d091e4d43
fi
font="/usr/share/grub/unicode.pf2"
fi
if loadfont $font ; then
set gfxmode=auto
load_video
insmod gfxterm
set locale_dir=$prefix/locale
set lang=en_US
insmod gettext
fi
terminal_input console
terminal_output gfxterm
set timeout=5
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/10_linux ###
menuentry 'linux' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-true-6b44daaa-610c-4f23-a632-569d091e4d43' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_msdos
insmod ext2
set root='hd0,msdos1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 6b44daaa-610c-4f23-a632-569d091e4d43
else
search --no-floppy --fs-uuid --set=root 6b44daaa-610c-4f23-a632-569d091e4d43
fi
echo 'Loading Linux core repo kernel ...'
linux /boot/vmlinuz-linux root=UUID=6b44daaa-610c-4f23-a632-569d091e4d43 rw quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initramfs-linux.img
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/20_linux_xen ###
### END /etc/grub.d/20_linux_xen ###
### BEGIN /etc/grub.d/30_os-prober ###
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###
### BEGIN /etc/grub.d/41_custom ###
if [ -f ${config_directory}/custom.cfg ]; then
source ${config_directory}/custom.cfg
elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then
source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###
### BEGIN /etc/grub.d/60_memtest86+ ###
### END /etc/grub.d/60_memtest86+ ###
p.s. i didn't think you needed those, because i thought they had default values.
edit: i guess i need 'grub-mkconfig -o /boot/grub/grub.cfg '
Last edited by aldoiljazi (2013-09-18 07:31:39) -
Satellite 1900-803: Hi-Speed USB 2.0 card doesn't work
i have a satellite 1900-803 laptop. I recently bought and installed a Belkin Hi-Speed USB 2.0 Notebook Card but it doesn't work. the card's manual says that after successful installation i should see a second "universal serial bus controllers" heading which i didn't. i even had it replaced it with another one thinking that there might be some problems with the drivers, but it still doesn't work. everytime i plug in a device such as an mp3 player, a digital camera or a usb storage device, windows just suddenly locks itself up, the cursor won't move, the ctrl-alt-del function doesn't work, and the worst of all, i can't turn off the machine!
the card says that it runs on any 32-bit slot.
i've browsed the user's manual and the device manager to see if mine is a 32-bit one, but i can't really find it. is this probably the reason why it won't work? or is there any other reason for it not working? if this is the reason, is there a way where i can upgrade my laptop's pc card slot to make it work?
please help.
i've posted this question yesterday morning and haven't got a single reply. is it because it has got to do with an older laptop? please, anybody, help..........
Message was edited by: wes0702Hi
Did you check the Bios? I assume the Toshiba Bios was preinstalled on your notebook. Am I right? There should be an option for changing the PC card controller mode.
There you can change the controller mode to auto-selected, PCIC compatible or Card bus/16-bit.
If the card supports 32 bit so you shouldnt use the 16bit option.
I think you should play a little bit with this option and possibly the card will work. -
HP Pavilion dv8210us sound card doesn't work.
Computer p/n ET831UA#ABA came with WIN XP Home Edition. Label states designed for Windows XP, Windows Vista Capable. I formatted the harddrive and loaded Windows Vista Business 64 bit. I downloaded and installed all drivers that were recommended by HP but my Sound and Audio doesn't work. Neither does my Mass Storage Controller nor my PCI Modem. All were working with the WIN XP. Need help on how to getting everything working.
This question was solved.
View Solution.You're very welcome.
You enjoy the rest of your weekend too! -
KA780G second network card doesn't work
Hi everybody,
Today, I put an second network card on the KA780G board (it's for a round robin network), on a free PCI slot, and this card isn't recognised by Linux and Windows (in Windows XP, when the network card is connected, my graphical card works bad as well).
I tested this network card in another computer and it's working well, I try with another type of network card and it's not working.
I upgraded the BIOS with the latest release and reset the bios parameters but it doesn't work.
Do I need to put some specifics parameters in the BIOS ?
Someone as an idea ?
Thanks
MattAs you want... but I know the truth
Transfert a file takes me twice the time when the second network card was unpluged (the test was made with two differents files with the same size, this is for keeping disk caching speeding the transfert).
I think, your're not understanding, so let me explain the achitecture of my network : two computers pluged to my "super magic switch" (each with one network card) and my NAS with two round robin's network card.
I transfert one file from the NAS to the first computer and at the same time another file from the NAS to the second computer. The network speed was (on the NAS) about 24MB/s (see with the system monitor).
If you're right explain me why many people using port trunking with their switches ?
Matt.
Maybe you are looking for
-
It has quit working with "liverez" which is my web based reservation program. The place I login is https://reservations.liverez.com/login.asp?LogOff=True&Return=Res but once I login, the site does not work as it did before. The website that correspon
-
having problems receiving mail via iCloud. I cannot revise the setting in Mail for mail from the incoming server the "box" is jammed and wont let me alter the details. reluctant to delete the icloud mail box and start again if it's going to delete ev
-
Erreur d'installation CS5.5 master LS4
Bonjour, j'ai essayé d'installer CS5.5 master collection LS4 (français) et seuls photoshop et indesign sont installés...Voir le log: Exit Code: 6 -------------------------------------- Summary -------------------------------------- - 17 fatal error(s
-
Portal Form for a Many to Many relationship
I have 3 tables (well there are actually more but i'm glad when i can do the trick with 3 at the moment): T_JOURNAL (JOURNAL_ID, JOURNAL_NAME) T_CONTENTBROKER (CONTENTBROKER_ID, CONTENTBROKER_NAME) HT_JOURNAL_CONTENTBROKER (JOURNAL_ID, CONTENTBROKER_
-
Poor audio quality after exporting to .MOV.
Voiceover in my video sounds crystal clear in the timeline but then thin and "rattley" after export when playing back with Quicktime player. Background music on other tracks always seems to be unaffected. Audio export set to AAC, 48 kHZ, Stereo. I mu