[Solved] Machine shutdown after some time

Hi all,
I have a machine with an Intel J1900
It has installed:
last kernel
Plasma 5
Gummiboot
SDDM
Intel drivers
all is ok, but when the machine is some hours up, the machine shutdown by itself. This cannot be a hardware failure because It performs a perfect shutdown.
How can I start to check the issue? any idea?
thanks in advance!
Last edited by zofiel (2015-04-04 08:24:04)

Any power management system installed (eg. upower) with screensaver set up to shutdown (instead of hibernate) after some time?
journalctl -b -1
look here at previous system log and see last lines if you can find anything wrong

Similar Messages

HT1476 when i charged my iphone on y pc after some time showing charger not supported with this accessory what have to do to solve it

when i charged my iphone on y pc after some time showing charger not supported with this accessory what have to do to solve it

If you did not do a reset of your iPod please try that (you will not lose any data)
Reset iPod touch: Press and hold the On/Off button and the Home button at the same time for at least ten seconds, until the Apple logo appears.
If this does not work inspect the opening in your iPod where the cable connects. Look for any debris and clean it (a magnifying glass may be required).

GPRS services suddenly stop working after some time abt 4 hrs.Airplane on off solves it

I am using a factory unlocked iPhone 4 GSM in India. Iam currently using it on airtel network 2G services i.e GPRS services. Now the problem I have noticed is that the GPRS services suddenly stop working after some time say about 4 hours. Then what i do is to turn airplane mode on and then off or restart the phone and GPRS starts working. Agan after some time I have to repeat this exercise. Please help soon. This is happening since the time i bought this phone i.e from past 20 days. I have tried allpossible network settings and resetting network but nothing helped. everything else is working perfect.

Hi Syed,
I have also started facing the exact same problem since the past few months with my docomo service.
Earlier, EDGE / GPRS used to work just fine from my workplace where the network was good.
But recently, I got my iphone replaced, due to a network problem, from an apple store in indianapolis, and also upgraded to ios 5.....so not sure now whether this intermittent EDGE / GPRS outage is due to the new hardware or the new OS.
Did you upgrade to iOS 5 and did it help?
PS: iOS 5.0.1 also doesn't seem to be helping, I still need to restart the phone to get EDGE / GPRSt to work.....will try out the airplane mode thing....at least that shouldn't take as much time as a full reboot.
Regards,
Hemant

OAS4081 on RH6.2 hangs after some time

I installed OAS4081 on Redhat6.2. It seems to work fine... for a couple of hours. After some time (ranging from several hours to one day, depending on the activity I think) the listener does not respond anymore. Even a 'telnet <host> 80 - GET /' does not return anything. There are no processes taking up cpu-time. Memory usage (using top) seems ok (150Mb total). The only way to solve, it to 'owsctl stop -s website40', but still some processes remain and need to be killed -9. Then restarting the website makes it ok again.
Also using 'vmstat 1' I have the impression that free memory is decreasing slowly (max 1Mb/5min). But when the website hangs, there is still enoug free memory (+200Mb).
If anyone has the same experience, or any tips, please let me know. We would like to use this website in a production environment.
I use only PL/SQL on an 8.1.5 database on a remote machine.
Geert
[email protected]
P.S. I applied the /pfoo/stat patch as described in the forum elsewhere.

We haven’t managed to repro this problem yet – we’ve run it on a couple of different machines using 2.5 and tested it repeatedly and can’t get it to fail. So, we have some more questions:
* What mode are you running in? GPU,CPU or Flash?
* If GPU, do you only see this hang in GPU mode, or can you reproduce it in CPU or Flash mode?
* If GPU, what is the date and version number of the NVIDIA GPU driver you is using? (and is it up to date – new drivers can be downloaded here http://www.nvidia.com/Download/index.aspx?lang=en-us)
* When you hit "Build and Run" are you changing anything? (e.g. editing the filter code, changing modes, changing images etc.)
* Can you make the images you’re using available to us?
Thanks
Bob

N73 got shuts down automatically after some time

hi,
my n73 music edition gets shut down after some time autmatically please can anybody tell me the reason.

The reason is that nokia phones have many bugs and problems.
A common cause of this problem is 3G. If the phone is in a weak 3G area the loss of 3G signal can cause the phone to reboot. It's an old problem thats been affecting nokia's for years. Disabling 3G can stop the random shutdowns.
It may also be worth updating the phones firmware but this is a fairly risky procedure that can cause more problems than it solves.

WL 10.3 - Quartz's jobs stops after some time of correct executing

Hi,
I have a webapp (backend only) that is deployed on WebLogic 10.3 AS. In this webapp 5 quartz's job are executed (cron trigger). Two of them run 3 times a day, the next two of them execute every 5 seconds and the last one starts every 20 seconds.
The problem is that after some time of correct execution (about 20 min.) one on the jobs hangs on, then after some time (about 10 min.) the second one hangs on and finally only one of job (it's always the "20" second job) executes correct for a long time, then also stops. Above, concerns the only the "5" and "20" seconds jobs. All of the jobs are stateful and Oracle DB is used for synchronisation.
In DB I see that "TRIGGER_STATE" in "TRIGGERS" tables has value of "BLOCKED" for the jobs that hang on. Whenever the job crashes I see the following entry in the WL's log:
####<2011-05-30 08:50:11 CEST> <Info> <RJVM> <server_name> <AdminServer> <[ACTIVE] ExecuteThread: '5' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1306738211453> <BEA-000513> <Failure in heartbeat trigger for RJVM: -6468277378824263512S:127.0.1.1:[7001,7001,-1,-1,-1,-1,-1]:test_domain:test-server
java.io.IOException: The connection manager to ConnectionManager for: 'weblogic.rjvm.RJVMImpl@559e - id: '-6468277378824263512S:127.0.1.1:[7001,7001,-1,-1,-1,-1,-1]:test_domain:test-server' connect time: 'Mon May 30 08:45:11 CEST 2011'' has already been shut down.
java.io.IOException: The connection manager to ConnectionManager for: 'weblogic.rjvm.RJVMImpl@559e - id: '-6468277378824263512S:127.0.1.1:[7001,7001,-1,-1,-1,-1,-1]:test_domain:test-server' connect time: 'Mon May 30 08:45:11 CEST 2011'' has already been shut down
     at weblogic.rjvm.ConnectionManager.getOutputStream(ConnectionManager.java:1719)
     at weblogic.rjvm.ConnectionManager.createHeartbeatMsg(ConnectionManager.java:1662)
     at weblogic.rjvm.ConnectionManager.sendHeartbeatMsg(ConnectionManager.java:599)
     at weblogic.rjvm.RJVMImpl$HeartbeatChecker.timerExpired(RJVMImpl.java:1584)
     at weblogic.timers.internal.TimerImpl.run(TimerImpl.java:273)
     at weblogic.work.SelfTuningWorkManagerImpl$WorkAdapterImpl.run(SelfTuningWorkManagerImpl.java:516)
     at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201)
     at weblogic.work.ExecuteThread.run(ExecuteThread.java:173)
>The quartz version I use is 1.8.4.
I use my own implementation of scheduler to start the jobs at the deploy time. Jobs are also always unscheduled when the app is undeployed. After undeploying all entries from quartz's tables are erased excepting the one in "SCHEDULER_STATE" table.
The webapp is tested standalone but it will be in the production environment it will be clustered (two nodes).
What can cause the problem? And how to solve it?
Below is my quartz.properties file as it's deployed with webapp:
#============================================================================
# Configure Main Scheduler Properties
#============================================================================
org.quartz.scheduler.instanceName = SimulatorClusteredScheduler
org.quartz.scheduler.instanceId = AUTO
#============================================================================
# Configure ThreadPool
#============================================================================
org.quartz.threadPool.class = org.quartz.simpl.SimpleThreadPool
org.quartz.threadPool.threadCount = 10
org.quartz.threadPool.threadPriority = 5
#============================================================================
# Configure JobStore
#============================================================================
org.quartz.jobStore.misfireThreshold = 60000
#org.quartz.jobStore.isClustered = true
#org.quartz.jobStore.clusterCheckinInterval = 20000
#org.quartz.jobStore.class = org.quartz.impl.jdbcjobstore.JobStoreTX
org.quartz.jobStore.class = org.quartz.impl.jdbcjobstore.JobStoreCMT
#org.quartz.jobStore.driverDelegateClass = org.quartz.impl.jdbcjobstore.oracle.OracleDelegate
org.quartz.jobStore.driverDelegateClass = org.quartz.impl.jdbcjobstore.StdJDBCDelegate
org.quartz.jobStore.useProperties = false
org.quartz.jobStore.dataSource = myDS
org.quartz.jobStore.nonManagedTXDataSource = myDS
org.quartz.jobStore.tablePrefix = QRTZ_
org.quartz.jobStore.isClustered = true
org.quartz.jobStore.clusterCheckinInterval = 20000
#============================================================================
# Configure Datasources
#============================================================================
org.quartz.dataSource.myDS.jndiURL=${org.quartz.dataSource.myDS.jndiURL}
org.quartz.dataSource.myDS.jndiAlwaysLookup=true
org.quartz.dataSource.myDS.java.naming.factory.initial=weblogic.jndi.WLInitialContextFactory
org.quartz.dataSource.myDS.java.naming.provider.url=${org.quartz.dataSource.myDS.java.naming.provider.url}
org.quartz.dataSource.myDS.java.naming.security.principal=${org.quartz.dataSource.myDS.java.naming.security.principal}
org.quartz.dataSource.myDS.java.naming.security.credentials=${org.quartz.dataSource.myDS.java.naming.security.credentials}
#======================================================================
   # Configure Plugins
#======================================================================
#org.quartz.plugin.jobInitializer.overWriteExistingJobs = true
#org.quartz.plugin.shutdownhook.cleanShutdown = true Any help would be greatly appreciated.

Thanks for you response,
I have a entry, in web.xml, because of this this working at startup time. (connecting the quarts scheduler)
When server and application started every thing it's working but after some time(mostly after 30 minutes), without any change in server/application we are getting the above error.
We have entry in web.xml file like this.
<ejb-local-ref>
<ejb-ref-name>ejb/DXTrackingSession</ejb-ref-name>
<ejb-ref-type>Session</ejb-ref-type>
<local>com.sample.app.ejb.tracking.DXTrackingSession</local>
</ejb-local-ref>

Sun One Web Server connection pool goes stale after some time

Hi all,
I have a few web applications running on Sun One Web Server 6.1 (SP4). I configured a connection pool via the web admin of the web server. I do not know why the connections in the connection pool are never released after some time (this happened for 3 times with a couple of months in between). I need to reboot the web server to solve this problem everytime the connection pool goes stale. I have verified that the resources are released (stream and connection are closed) with proper programming logic. Even so, I think that the connections will be timed out (the setting is 5 minutes) by the web server as a bulletproof even if the resource is not released properly as implemented in the code logic. Can anybody help on this? I have been troubled by this problem by weeks.
Thank you in advance.

Hi all,
I have a few web applications running on Sun One Web Server 6.1 (SP4). I configured a connection pool via the web admin of the web server. I do not know why the connections in the connection pool are never released after some time (this happened for 3 times with a couple of months in between). I need to reboot the web server to solve this problem everytime the connection pool goes stale. I have verified that the resources are released (stream and connection are closed) with proper programming logic. Even so, I think that the connections will be timed out (the setting is 5 minutes) by the web server as a bulletproof even if the resource is not released properly as implemented in the code logic. Can anybody help on this? I have been troubled by this problem by weeks.
Thank you in advance.

Firefox consumes a lot of CPU resources after some time

Hi,
I've upgraded from Firefox 3.5.16 to Firefox 5.0 on Linux i386 with 512 MB RAM. Everything is working fine until after "some time" (don't know the exact time period) the CPU load increases to 100%, my average system load explodes and the system is swapping memory wildly. This suddenly happens, even if Firefox is in the background while I'm working on different things. So it does not belong to any memory-hungry stuff like Flash pages or JavaScript sites.
I don't think the problem is caused by my extensions (adblock, noscript, multifox, tabloc) or plugins (mplayer/Flash) either.
I think it is the Javascript Garbage Collector. I could tweak its cycle time in about:config, but this would just be work around the problem.
Note that I usually have many open (app) tabs that extensively use Javascript and AJAX.
I really like the new Firefox features, but I haven't expected that "5.0" stands for 5.0 average system load. Sorry couldn't resist that remark ;D
bcctr

I updated to Firefox Aurora this morning. Problems seem to be solved. Thank you!

Cannot erase authorization. "Unable to erase authorization. Please try after some time." Please help!!

I am having a number of problems with Digital Editions, and I have tried the chat options numerous times but no one seems to be able to help me. I cannot express how disappointed I am with Adobe. I have an ebook that I paid a lot of money for and I need to access it for work, but when I try to download the e-book I get the error message E_ACT_NOT_READY. The forums say I need to deauthorise my account, but when I try to erase authorization I get the message "Unable to erase authorization. Please try after some time." This has been happening for weeks. For 2 weeks I have been trying to solve this problem. Can somebody please help me or give me a phone number to call to reach adobe? I am desperate at this point.

If due to some reason, you are unable to deauthorize ADE, follow the below steps:
Mac:
1. Go-> Go to folder.
Go to folder dialog will appear.
2. Type ~/Library/Application Support/Adobe/Digital Editions
drag the activation.dat file to the trash.
ADE will be deauthorized now.
Now Authorize ADE again.
ADE will be deauthorized now.
Now Authorize ADE again.
Windows:
Choose Start > Run.
In the Open text box, type regedit and then press Enter. The Registry Editor opens.
In the left pane of the Registry Editor, locate the following registry key:
HKEY_CURRENT_USER\Software\Adobe\Adept
Right-click the Adept key and choose Delete.
In the Confirm Key Delete dialog, click OK.
Your authorization will be deleted.
ADE will be deauthorized now.
Now Authorize ADE again.

After recent upgrade to IOS 7 i an seeing systems rebooting very frequently. it just goes offline and comeback online after some time. IS this hardware issue or others also facing the same

After recent upgrade to IOS 7 i an seeing systems rebooting very frequently. it just goes offline and comeback online after some time. IS this hardware issue or others also facing the same

Hello there, Kishoresaraogi.
The following Knowledge Base article provides some great steps to troubleshoot your issue:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Particularly:
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

N8 after some time handsfree mode

My N8 gets into handsfree mode after some time....
I have to press 2 times then the handset/handsfree button to get the connection back!
Solved!
Go to Solution.

Sent you the mail
Hope it helps

No http after some time in user account

I have a strange behavior. After a restart (Software Update), I couldn't visit any webpages. Network diagnostics said everything was ok. I could send and receive email. I tried another browser: Same result. I logged into my administrator account: everything worked.
I could fix that problem by changing my proxies settings from "Using PAC-File" to "manually", but the next time, I wanted to use the internet, same problem.
So now, I have to toggle the proxies settings a couple of times until the internet works again, after every sleep or restart. My wife even lost the "connection" after working some time in other programs.
This is very annoying, so help would be appreciated.

Hello @Polysept,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your monitor turns black after some time in use, and I would be happy to assist you in this matter!
Since you mentioned that your desktop was overheating, I recommend following the steps in this document on Reducing heat inside the PC to prevent overheating.
If the issue persists, please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

SAP instance getting stop after some time....

Hi,
Installed SAP on Cluster .SAP runs fine before and after switchover cluster when we do manually.
Problems comes after scripting ,While starting SAP Instance with SCript its work fine but after some time instance get fail.
And error comes
15:09:55
/usr/sap/SID/SCS01/exe/sapcontrol -prot NI_HTTP -nr 01 -function Stop
05.03.2014 15:09:55
Stop
OK
15:09:57
Instance on host insapr3pi01 stopped
15:09:57
Waiting for cleanup of resources
And it stop instance after some time.We are using Veritas (VCS cluster).Its continously search for cleanup of resources!!!!!!!
Regards
Adil

Sap instance start by that script but after sometime it give message in cluster software that Waiting for Cleaning of Resources.And after sometime it shutdown that instance.
Hi Adil,
When an external application (in this case SAP NetWeaver) is clustered with VCS, there are options to execute scripts at various operation cycles of the VCS agent for the application in question. I would recommend reviewing the application group configuration, corresponding VCS logs, as well as the path to the scripts and their content.
I can assist from VCS perspective if the question still stands.
Regards,
Villi

SA 540 drops wan connectivity after some time interval

hello guys,
I have problem. after a certain period of time (ranging from 2 minutes to several hours) the unit keeps dropping the WAN connection, making the unit unaccessible from the WAN side. The strange thing is, that when the connection is dropped, the unit is perfectly accessible from the LAN side, the WAN LED is still on, status info shows the WAN link up, and packet trace shows broadcasted traffic on the WAN interface, so only the directed communication to and from the ISPs gateway (configured to fix IP) seems to be blocked for some reason. When this happens, then plugging the WAN cable to the Optional WAN port enables traffic again, but it is also dropped after some time, and then only power cycling the unit restores WAN connectivity.
please suggest me as soon as possiblethat how to fix this problem?
Awaiting for valuable reply.....

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

BFF62048 Error after some time

Hello everyone,
I need CAN to communicate between a converter and our test cell. I use an NI PCMCIA-CAN/2 Card and LabVIEW 2012 SP 1. My program works fine but after some time I get an the error BFF62048. I know what it means but I don't know where the problem is nor how to solve it.
I use the Channel API for programming the CAN-communication.
The problem is I need to write at different timings on the can. Some messages need to be sent at 12ms others at 100ms. Therefore I initialized the messages in different tasks.
For CAN 1 have 1 readtask and 4 writetasks. For CAN 2 I have 1 readtask and 2 writetasks. I hope it is not too much for this little card.
The readtasks were both executed at 10ms after each other. The writetasks are executed in several parallel loops, except for one writetask. I need to send back an "alive value" immediately, so I read a value from my CAN-read-array and put it back on the CAN with a writetask. Which means I have to access the card 3 times in one loop.
I reduced the execution of my CAN-read-loop from 10ms to 20ms and the program runs much longer. (from ~30 min to 4 hours)
In my opinion the problem should occur immediately after I started my program not after some hours.
If someone have some advices for me, that would be great.
Thanks,
Rino

I use Labview 2012 (fully updated). Driver Version is 2.7.4
I don't think there is a problem with the bus load. Only 50 % of the capacity is used.
Unfortunately we are in lack of hardware, but I'm sure my code will work on a "real" PCI-CAN card. Is it possible, that the PCMCIA-card maybe has a problem with too many tasks? I couldn't find any information regarding the task limit in the hardware specification or I'm blind
I attached the project as *.zip file. I had to remove the can database files (*.dbc) because they are confidential.
Attachments:
Abnahme_629.zip ‏1058 KB

[Solved] Machine shutdown after some time

Similar Messages

Maybe you are looking for