[SOLVED] Vostro 1310 lan connection

Hi there, I'm having trouble getting my laptop's networks setup. It's a Dell Vostro 1310 and has a Realtek 8100c network card and the wireless card is an Intel Pro Wireless 3945.
At the moment I have neither of the cards connecting, but I haven't tried the wireless yet and need the ethernet going first as that is the way in which I connect to my adsl router.
It detected the network card's module correctly it seems as r8169 is loaded with rc.conf.
Here's part of my rc.conf:
lo="lo 127.0.0.1"
eth0="dhcp"
INTERFACES=(eth0)
gateway="default gw 192.168.1.1 eth0"
ROUTES=(gateway) /also tried ROUTES=(!gateway)
It talks about setting device profiles, however I don't know how to do that.
I wonder if the driver for my nic isn't working for my card? I have got the latest Realtek drivers but I only got errrors on a make modules clean. I also don't think it works for a kernel later than 2.6.23.
Could someone help me figure this out?
Last edited by Phineas (2008-08-15 23:18:20)

After about a week with Kubuntu and KDE4 I have come back to Archlinux. At the end of that time it wouldn't connect to my router at all. Now in Archlinux, with significantly less installed it's connecting automatically. My rc.conf is slightly different, I don't know what I did other than that, I selected iproutes and dnsutils during install of the latest 32-bit arch, but I don't know. At least it works. Here is part of my rc.conf file:
MODULES=(r8169 iwl4965 snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore)
eth0="dhcp"
INTERFACES=(eth0)
gateway="default gw 192.168.1.1"
ROUTES=(gateway)

Similar Messages

Lan connectivity Issue on autonomous AP with throttles

          Hello,
I encounter a strange problem on several AP 1242 in version 12.4(25d)JA1 of a customer :
He has 10 autonomous AP covering a factory and is using them for laptop connectivity and TOIP with mainly 7921 Cisco Wifi Phones.
The phones are configured to use only 802.11a.
The APs loose LAN connectivity randomly and therefore the clients don't work anymore.
The AP are connected on a 2960 and a 3560 wich are in turn connected on a 3750 wich route the trafic.
After checking spanning-tree no loops are present.
When I check the counters on the AP involved I see the "trhottles" and "ignored" counters incrementing on the fa0 link of the AP impacted wich mean I think it can't handle the incoming traffic. This incoming traffic seems not to be too big however. I can see drops on the switch interface connecting the AP.
There is a lot of roaming on the AP due to people walking in the factory with their wifi phones.
Here is a view of the fa0 counters :
AP1242-LOGIST#sh int fa0
FastEthernet0 is up, line protocol is up
Hardware is PowerPCElvis Ethernet, address is 001d.a1ce.26e2 (bia 001d.a1ce.26e2)
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Full-duplex, 100Mb/s, MII
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/160/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 81000 bits/sec, 53 packets/sec
5 minute output rate 29000 bits/sec, 26 packets/sec
     7447113 packets input, 674891974 bytes
     Received 286839 broadcasts, 0 runts, 0 giants, 549631 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 549631 ignored
     0 watchdog
     0 input packets with dribble condition detected
     4422100 packets output, 609868806 bytes, 0 underruns
     0 output errors, 0 collisions, 4 interface resets
     1 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
Here is a small part of logs concerning roaming, i don't see errors or log indicating that something is wrong nor in the switches log :
Jun 6 12:57:27.007: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001E4A3EE15D 001e.4a3e.e15d Associated KEY_MGMT[WPAv2 PSK]
Jun 6 12:57:42.499: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 12:58:02.620: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 12:58:03.653: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 12:59:15.564: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 12:59:15.564: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 12:59:41.905: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 442b.0355.ab28 Reason: Previous authentication no longer valid
Jun 6 12:59:54.728: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP442B0355AB28 442b.0355.ab28 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:01:12.541: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:02:35.841: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001e.4a3e.d875 Reason: Previous authentication no longer valid
Jun 6 13:02:36.489: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   ec85.2f7c.c837 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:03:29.256: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:03:29.256: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:04:32.754: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001E4A3ED875 001e.4a3e.d875 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:06:47.858: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001e.4a3e.e15d Reason: Previous authentication no longer valid
Jun 6 13:07:18.107: %DOT11-6-ROAMED: Station 001f.6c7a.5101 Roamed to 001d.a2bb.15b0
Jun 6 13:07:18.107: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001f.6c7a.5101 Reason: Sending station has left the BSS
Jun 6 13:07:38.109: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:07:42.031: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:07:42.031: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:07:46.489: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001F6C7A5101 001f.6c7a.5101 Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:27.712: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:44.502: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:08:44.572: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:56.778: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:08:56.779: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:09:17.874: %DOT11-6-ROAMED: Station 001f.6c7a.5101 Roamed to 003a.9a92.8d70
Jun 6 13:09:17.874: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001f.6c7a.5101 Reason: Sending station has left the BSS
The AP are configured as follow :
Current configuration : 5184 bytes
! No configuration change since last restart
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP1242-LOGIST
logging rate-limit console 9
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
clock timezone gmt+1 1
clock summer-time gmt recurring last Sun Mar 2:00 last Sun Oct 3:00
dot11 syslog
dot11 vlan-name Data vlan 11
dot11 vlan-name Voix vlan 14
dot11 vlan-name Webguest vlan 5
dot11 ssid WLAN_data
   vlan 11
   authentication open
   authentication key-management wpa
   mbssid guest-mode
   wpa-psk ascii 7 10600C0E261B173C252203797479633F371A29
dot11 ssid WLAN_voice
   vlan 14
   authentication open
   authentication key-management wpa
   mbssid guest-mode
   wpa-psk ascii 7 080F49592A1500203B2D25567A7A7622263C0C
dot11 ssid Webguest
   vlan 5
   authentication open
   mbssid guest-mode
dot11 wpa handshake timeout 1000
dot11 arp-cache
dot11 priority-map avvid
dot11 phone
power inline negotiation prestandard source
class-map match-all _class_voice0
match ip dscp ef
class-map match-all _class_voice1
match ip dscp cs3
policy-map voice
class _class_voice0
set cos 6
class _class_voice1
set cos 3
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 11 mode ciphers aes-ccm
encryption vlan 14 mode ciphers aes-ccm
ssid WLAN_data
ssid WLAN_voice
ssid Webguest
mbssid
power client 17
channel 2472
station-role root
dot11 qos class voice local
    admission-control
    admit-traffic narrowband max-channel 75 roam-channel 6
dot11 qos class voice cell
    admission-control
no cdp enable
infrastructure-client
interface Dot11Radio0.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
bridge-group 5 subscriber-loop-control
bridge-group 5 block-unknown-source
no bridge-group 5 source-learning
no bridge-group 5 unicast-flooding
bridge-group 5 spanning-disabled
interface Dot11Radio0.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio0.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
bridge-group 14 subscriber-loop-control
bridge-group 14 block-unknown-source
no bridge-group 14 source-learning
no bridge-group 14 unicast-flooding
bridge-group 14 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 11 mode ciphers aes-ccm
encryption vlan 14 mode ciphers aes-ccm
ssid WLAN_data
ssid WLAN_voice
ssid Webguest
no dfs band block
mbssid
channel dfs
station-role root
interface Dot11Radio1.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
bridge-group 5 subscriber-loop-control
bridge-group 5 block-unknown-source
no bridge-group 5 source-learning
no bridge-group 5 unicast-flooding
bridge-group 5 spanning-disabled
interface Dot11Radio1.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio1.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
bridge-group 14 subscriber-loop-control
bridge-group 14 block-unknown-source
no bridge-group 14 source-learning
no bridge-group 14 unicast-flooding
bridge-group 14 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
speed 100
full-duplex
no cdp enable
hold-queue 160 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
no cdp enable
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
no bridge-group 5 source-learning
bridge-group 5 spanning-disabled
interface FastEthernet0.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
no bridge-group 11 source-learning
bridge-group 11 spanning-disabled
interface FastEthernet0.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
no bridge-group 14 source-learning
bridge-group 14 spanning-disabled
service-policy input voice
service-policy output voice
interface BVI1
ip address 10.17.10.5 255.255.255.0
no ip route-cache
ip default-gateway 10.17.10.254
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging trap warnings
logging 10.15.51.115
no cdp run
bridge 1 route ip
line con 0
line vty 0 4
sntp server 10.15.1.50
sntp broadcast client
end
Does someone ever experienced a similar problem ?
When I shut radio interfaces they're is no more problems on the LAN. Can this be an overlapping coverage issue ?
Can someone please give me advices on how to troubleshoot this issue ?
Thank you in advance as I'm a bit stuck.
Best Regards,

     Hi Scott,
Thanks for your reply.
Do you think this can be the origin of the issue my customer encounters or is it only to be standard ? As this change will have to be made on all clients, if there is a chance it solves the problem I will do it ASAP, if not I will delay it in a less busy period :-)
Can the constant roaming associations and dissasociations overload the AP and make it stop responding on the LAN or is it only a throuhput problem ?
Thanks in advance for your answer.
Best Regards,

802.1x on a wired Lan Connection

Dear Community,
i have the job to connect a Windows CE 6.0 device to a Network (wired) with 802.1x. The switch to wich i connect the device is operating as authenticator and the Wince device is the supplicant. A Radius Server with AD is also present .
All the informations and samples that i can find are relating to wireless LAN connections (WZCSVC). A description of the EAPOL API is also absent (or i was not able to find it).
I'm afraid that Wince 6.0 is not prepared for using 802.1x over a wired connection like Win XP can, but i'm not sure about that. I can not find a definite statement whether it is possibe or not.
Does anybody know if it is possible and/or how i can solve this problem.
Regards Achim

Community,
anybody has answer to this problem? I have to do the same thing...
Achim,
did you solve this problem?Thank you
in advance for any help you
can provide.
Regards Bruno

No network LAN-connection after iOS 5.1.1update

Today i tried to solve a big issue after updating my AppleTV's to 5.1.1 (actual version: AppleTV3,1_5.1_10A406e_Restore.ipsw). After updating my Apple TV´s, they could not connect to the Apple activation server. No Home Sharing was adjustable and also logging in iTunesStore was not possible. The update I have done via LAN cable, and I changed nothing in my network configuration. The network (networkadress via DHCP) is indeed set up by default in the AppleTV automatically. Nevertheless, nothing went. Then I removed the network cable and made a reset of the AppleTV and tried to connect via Wi-Fi. With Wi-Fi, he finds the activation server and everything works as it should. Home Sharing, iTunes, streaming. However, once the network cable is plugged in and the Apple TV is restarted, it is again not possible to get access the iTunesStore. Home Sharing is not possible. The networkcable are fine. Both MacBook, as well as my TVs have internet connection over the same network cable. If I unplug the network cable from the AppleTV again, anything goes. Only via WLAN, but it's just too slow to stream data from my Mac. I have this "strange behavior" on 3 AppleTV 3.Gen., which are in the apartment. The previous iOS-Version on the same network cables, worked great. Can anyone reproduce the problem? Or have I now 3 bricked devices? I tried to downgrade over itunes. But this is not possible anymore. I installed 3 times the update. But nothing goes. Please can anybody help me.

I found another link titled "Apple TV Death after update" and found several links that have proven to work to restore to the previous version. Here is my post:
"I had originally replied to a post titled "No network LAN-connection after iOS 5.1.1 update". That has been my issue after updating to 5.1. Wirless worked for me but iTunes match and Podcasts were slow to respond. I finally downgraded to the previous version (5.0.2). So far, my ATV3 has been operating exactly as it did out of the box. No more activation failed message, and all components of ATV are functioning flawlessly on my whole home LAN network.
I also wonder what Apple was thinking for releasing this update without adaquate testing. I can forgive them for Maps, but not this. ATV has been around long enough for all of the kinks to be worked out and any updates to just plain work. I did like the new menu displays in apps and how you could rearrange the program icons on the home screen.
Perhaps they will get it right. Some day. But until they show proof that any future updates are correct and provide detailed instructions on how to revert back to a previous version, I will be very leary of updating. Spending a week reading message boards on how to do a simple resotre is not my idea of how to spend my weekends.
As a side note, I am a PC, so to restore from an .ispw file located on your system, you must press the Alt & Shift keys togather, then click the Restore button, and a window will pop-up so you can select the location for the restore file."
Directions to restore:
"Yes you can. I am a PC. Download the .ipsw file and save to your desktop. Unplug the LAN, HDMI and power cable. Connect the usb cable from your laptop to the ATV. If iTunes does not automatically launch, start it. After iTunes is running, plug in the power cable to the ATV. iTunes will recognize the ATV and will open the restore window in iTunes.
Press the Alt and Shift keys togather, then click on the Restore button. A file window will open so you can navigate to the desktop (or where ever you saved the file). Select the AppleTV3,1_5.-.2_9B830_Restore.ipsw file. iTunes will start the restore process.
When you see the message that it has completed the restore, unplug the usb cable and power cable. Reconnect the LAN and HDMI cable then plug in the Power cable in that sequence.
Follow the setup procedure again and all should be as it was before."

Dell Vostro 1310, Close lid, Freeze

I just installed arch on my old Dell Vostro 1310.
It is a very fresh and simple install. The only packages I have installed are wget and sshd.
I.e I have no acpid running.
I have set HandleLidClose to ignore in logind.conf, but when I close the lid something happens and the laptop freezes.
ssh access also dies, and fans stop, so it is not just the screen.
What could be the issue here?
[EDIT]
Just noticed a strange workaround. If I have an active SSH connection to the machine, I can close the lid without problems.
If I close the ssh connection while the lid is closed, it is also still fine. But if I close it without any SSH connection, it freezes.
Last edited by inferred (2012-12-11 15:49:16)

I have c600, and I used to have some kind of the same problem with it. I had acpi, and it had difficulties to suspend to RAM and to HDD... there were always problems doing this kind of things. But i reconpiled mu kernel (2.6.10 rc1) with apm support, and dissabled acpi. Now all of this (standby, suspend, etc) is working just fine. When I close the lid, tc PC get asleep.. somekind of suspend to RAM, ot god-knows-where. When I open it, it wakes up... And all of the function buttons are working too... maybe just apm is "native" for this kind of systems.
good luck

Linksys Easy Link Advisor [ Lan Connected Users]

Hi. I am using Linksys Easy Link Advisor, I am using my Laptop and is connected through Wireless mode, Now one of my computer is connected through Lan line [ Ethernet cable]. The Lan line and Wireless both computers are working properly, but while I am using Wireless Laptop I am unable to watch Lan Connected computer.
In Router setting I have enabled Wireless MAC Filter and all the computer like Wireless and Lan Line computers are registered. But in Linksys Easy Link Advisor the Lan Line computer dosen't appear.
Please Help.
I am thankful from your team side which has helped me in solving many problems for Linksys Easy Link Advisor.
Solved!
Go to Solution.

I have Linksys Easy Link Version 3.11 (Build 9139.94)     Platform Version   11.1.9051.0
I connected my Laptop wirelessly through this and now I connected one more Laptop through Lan [ Ethernet Cable]. But I am unable to see this Lan Connected Computer. The Wireless computer can be viewed.
I disabled firewall from all like Windows Firewall Trend Micro Firewall, Still unable to add Lan [ Wire connected] computer through my Laptop which is wireless connected. But still I cant see the Lan Connected Computer on Wireless Computer.
Is there anything to do in router. I have Linksys Wag160N ADSL2+   [MAC-00226BF1F82]
Please help me.
Thanks.
Ghanshyam,
Dubai   U A E
(Mod note: Edited for guideline compliance.)

LAN connection not recognized

Config :
-wifi connection => airport (music)
-wifi conection => internet (disconnected when LAN connected)
-ethernet connection => internet
IMac lost connection with internet thru ethernet.
Don't understand why.
Don't know how to modify settings so we can have :
-wifi connection with airport (itunes and stereo)
-ethernet connection for internet
It worked in the past and suddenly it stopped
Thanks for your help
PS : I think the best would be a re-initialization of the network config

Thanks for the info but the pb is not solved.
Apple > System > Network :
Ethernet = automatic via DHCP (169.254.24.81)
PB= it gives me an IP address which does not correpond to the IP address range of the DSL box (192.168.1.1)
The most incredible is :
I connect a PC to the ethernet cable, it works !!!
I'm kind of dizzy...

LAN-Connection doesn't work sometimes

Hi,
Since two weeks I have been having some trouble with my LAN connection. Whenever I want to start a LAN connection, it doesn't seem to work. In System Preferences, I get the message "Cable unplugged". When I reboot my computer 3 times, it works. The problem is not the internet, because when I connect the cable to another computer, the Internet works immediately.
Does someone know how I can solve this problem?
Jeroen

No, it isn't. Like I said, when I connect the cable to another computer, the Internet works immediately.

LAN Connection Error: Panasonic DMP-BD35 Blu Ray Player

Hello,
My Panasonic DMP-BD35 Blu Ray player has a wired LAN connection port that is used to download firmware updates.
When I was using a DLink WBR-2310 with Verizon DSL the system worked perfectly with the BD35 player wired to a LAN port on the DLink router. I recently switched to Verizon FiOS and now the BD35 player is wired to LAN port 2 on the FiOS wireless router.
The BD35 is no longer able to connect to the network now that it is wired to the FiOS router. When I run the connection test an error is returned, "Cannot obtain IP Address using DHCP." However, all of my other network devices (Wii, Laptops, Desktops, Print Router, etc.) have had no problem connecting to the router, both wirelessly and wired. I have even wired a laptop to the jack that the BD35 is using and the laptop connects just fine (wireless turned off). Also, I checked the Port Configuration screen on the router and Port 2 is showing that it is connected at 100Mbps Full-Duplex when the BD35 is on, but the device does not appear on the list of devices connected on the My Network screen.
Here are the settings on the BD35:
- IP Address Auto Configuration (DHCP) = ON
- DNS Auto Configuration (DHCP) = OFF
- Auto Detect Connection Speed = ON
Does anyone have experience with this issue? Is it possible to setup a Static IP for the BD35 in the router using the MAC Address for the BD35?
Thank you!

I'm not familiar with the Panasonic BD35 but I would suggest that you try it with DNS Auto Configuration turned on.
You may also be able to set it up with a manual address that is way out of the range of anything that you woudl normally use.
Try the following:
Check the TCP/IP Address that your PC is getting. Assuming your IP Address is set to 192.168.1.x set the Panasonic to
IP Address: 192.168.1.200
Subnet: 255.255.255.0
Gateway: 192.168.1.1
DNS: 192.168.1.1
The Verizon STBs will use 100 to 150 and your other DHCP Devices woudl normally use the addresses between 2 and 99.
If you still have problems try using OpenDNS and set the DNS address to 208.67.222.222.
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it.
If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

How do I network my MacBook Air to a PC to utilize the PC's LAN connection?

Want to connect MacBook Air (10.8) to a PC over the PC's USB port.
Need to utilize the PC's LAN connection to connect to the internet.
Not allowed to connect the MAC directly to internet via Ethernet or WiFi.
PC is allowed to be connected to netowk.

This video will guide you to get the Ipad to print from a printer connected to the windows pc- http://www.youtube.com/watch?v=P_64MdjFoL0

Error Code 10 Intel 82579LM LAN connection on Portege R830-13C

After recent Windows 7 32 Bit update, the LAN connection is failing to start (Code 10) under device manager
"This device cannot start. (Code 10)"
I have tried uninstalling drivers / rolling back / and installing the following files from Toshiba support pages, but does not resolve the issue.
- lan-20110330164846
- fareg-20110331130330
How do I get Intel 82579LM Gigabit Network Connection on Portege 830 -13C to work?
(wireless is fine)

Hi
Error Code 10 is generated when Device Manager can't start the hardware device and usually its caused by outdated or corrupted drivers.
Therefore I think that driver installation should help to sort out this issue.
I would recommend doing this:
- Go to device manager and uninstall the LAN driver
- Reboot the notebook but dont install the driver
- Install the CCleaner and clean the registry
- Reboot the notebook once again
- Then go to device manager, choose the LAN card (Ethernet controller) and install the downloaded driver
As option I would recommend testing the LAN driver from Intel page.

HP Slate 21 Kit Kat OTA Update Fix for Audio Quality and LAN Connectivity

Recent Over The Air (OTA) update for Slate 21 Update
Link to thread discussion here, fix listed below -
ISSUE:
A previously applied HP Slate 21 Kit Kat Update (Android 4.4.2) over the air (OTA) update may have caused issues with audio quality or wireless LAN connectivity.
Audio Quality: Bass response will be poor. Audio will play but bass frequencies will be lacking.
WiFi Issue: 5 GHz band not functioning properly
Status:
A new update (17r25.1-011-11-WW) has been released over the air (OTA) to end users
Resolution:
Apply update 17r25.1-011-11-WW
If the user was previously on 17r25.1-010-10-WW then a Factory Reset should be performed to complete the resolution.
I work for HP, supporting the HP Experts who volunteer their time and technical knowledge to help others.

Pebbles65,
Thank you for visiting our English HP Support Forum. We are only able to reply to posts written in English. To insure a quick response it would be advisable to post your question in English. The following links are here to assist you if you prefer to post in the following Language Forum.
English: http://h30434.www3.hp.com
Spanish: http://h30467.www3.hp.com
French: http://h30478.www3.hp.com
Portuguese: http://h30487.www3.hp.com
German: http://h30492.www3.hp.com
Korean: http://h30491.www3.hp.com/t5/community/communitypage
Simplified Chinese: http://h30471.www3.hp.com/t5/community/communitypage
Cheers,
KarolB
I work for HP

Is it possible to control (screen share) my Mac Book on my PC over a LAN connection with fullscreen 1920x1080 resolution AND sound?

I've fiddled with Team Viewer and was able to control my Mac on my PC, but it wasn't over my LAN connection (it was slow), and it was a small windowed view without the Mac's sound. I want to cotrol my Mac, with my PC over LAN and on a 1920x1080 resolution with the Mac's sound on my PC.
(Sry for a almost report of this (https://discussions.apple.com/thread/4031259) but I forgot to ask about the sound).

well there is a program called logmein found at logmein.com. it fixes your resolution problem, but the speed is still not the best due to a lag still. As long as internet connections are decent, the lag should be minimal

How to solve the problem of connecting my iPad to Itunes while my iPad not working and show to connect to iTunes?

Question to all iPad users please help in this issue
How to solve the problem of connecting my iPad to Itunes while my iPad not working and show to connect to iTunes?
Thank you for help out.

Hi Jamalzoal,
Dose your computer have the most recent iTunes on it? When you connect the iPad 2 to your computer what happens? dose iTunes tell you the iPad need to be restored?
p.s. you post this question in the Apple Remote Desktop community. You would probable have gotten more an fast responses if you posted this in the iPad community.

Cannot re-boot after enabling K8T Neo LAN Connection

I've tried to enable the K8T Neo LAN controller in BIOS so that I can connect a Wireless Router to my PC. However, when I do this, the PC will not boot and I have to disable the LAN controller.
On booting-up the BIOS seems to be looking for an ethernet controller and a message states that either the device is not plugged in or the cable is faulty ! Why should enabling the onboard LAN controller affect the device the BIOS boots from ?
Can I plug a Wireless Router directly into the RJ45 LAN connection on the K8T Neo and if so, how ?
Thankyou for any helpful advice

Check to make sure you are not set to boot from network. Unfortunately I can't remember the exact name or where it is located, but it may help.
Quote from: Geps on 07-July-05, 22:52:17
as you say: a WIRELESS router is WIRELESS, how could you plugin a cable from a wireles router. or does it also have rj45 conectors?
if you want to use the wirreles function, you will need to buy a wirrles lan adapter (usb) for your pc
I have never seen a wireless router without rj45 connectors. (WAP yes, router no).
Good Luck
Jeremy

[SOLVED] Vostro 1310 lan connection

Similar Messages

Maybe you are looking for