SR520 - no ip name-server command missed

Hi all,
I'd like just notify the missing "no ip name-server" command in sr520 series router.
However is possible to enter the command "ip name-server" the only way to delete it
is to copy a modified config from tftp or other source to the startup-config.
Does anyone know if this behavior is normal?
In 800 series al work properly.
Thanks.
Gianluca

Seems a 'normal' nvgen IOS bug.

Similar Messages

How a router can resolve dns without ip name-server command?

Hello everyone,
A question about the command "ip name-server *.*.*.*"
If I didn't put in the DNS server, the router can still resolve the domain name. You can see the domain server is 255.255.255.255.
Why does this happens?
R4#ping www.cisco.com
Translating "www.cisco.com"...domain server (255.255.255.255) [OK]
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 184.31.192.170, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
R4#

Hi,
There is a name server inside the LAN. Before searhing in the DNS server, it checks the name server in the LAN to reduce the time for searching. The name server of the LAN is like a cache which stores the results coming from the DNS server.
So, it is name server of the LAN which is resolving the IP address.
Thank you.
* please rate the helpful posts.

Change name-server order

Hi,
I have some local name-servers configured on a router using the ip name-server command.
The router also knows about some external DNS servers that were supplied via DHCP - the WAN interface uses DHCP to obtain its IP address and gets some DNS servers as well.
However these external servers have never actually been used because the configured local servers were always used first.
Unfortunately the router lost contact with the local servers recently and is now using the external servers first, by default - if a lookup fails it then does not try the others. A lot of local lookups are obviously failing for hostnames that are local, that don't have public DNS entries.
So my question is - is there a way of clearing this name-server priority without shutting the WAN interface or reloading the router? I have tried removing the local DNS servers and re-adding them (no ip name-server xxx.xxx.xxx.xxx, ip name-server xxx.xxx.xxx.xxx), switching off the lookup service (no ip domain-lookup, ip domain-lookup), clearing the hosts table (clear host *) but the router is still stubbornly using the external DNS servers that it failed over to during the internal outage.
Thanks!

Well - in the end I shut / no shut the outside interface, which forced it to release the DHCP-learned DNS servers:
098312: Jun 5 23:18:34.236 BST: Clearing default gateway and route to x.x.x.x
098313: Jun 5 23:18:34.236 BST: Removing old default route x.x.x.x
098314: Jun 5 23:18:34.240 BST: Clearing route to DHCP server y.y.y.y
098315: Jun 5 23:18:34.240 BST: DHCP: Removing static route to 0.0.0.0 0.0.0.0 via x.x.x.x
098316: Jun 5 23:18:34.240 BST: Clearing DNS address a.a.a.a
098317: Jun 5 23:18:34.240 BST: Clearing DNS address b.b.b.b

Asynchronous reserve finally failed: missing name server configuration

Hi,
can anybody give me a hint why we get these errors?
"asynchronous reserveFinally failed: missing name server configuration, no logon known -> operation will be retried name reservation : name server=http://sapcoe01.bbn.hp.com:50000/, category=SAP_DevelopmentComponentName, name=hp.com/appl/tax, reservationKey=63415681, state=FINALIZE_PENDING"
The development objects are listed in SLD with status PRERES. The Name Server location is configured in DTR with the logon data. The name server is also listed in the development configuration.
Where else could be the cause for this error?
Many thanks for any hints!

Hi Martin,
Here you can see the *_PENDING items: http://<host>:50000/dtr/sysconfig/support/NameReservationList
And here you can configure the name server: http://<host>:50000/dtr/system-tools/administration/NameServerConfiguration
The solution is to define your name server a second time with a slightly different URL. The first entry you already defined probably uses the fully qualified hostname, e.g. http://<host>.mycompany.com:50000/sld/cimom. Define the same name server again but without the domain and without the /sld/cimom path, e.g. http://<host>:50000/. Actually it should correspond to what's shown in the error message, e.g. "operation will be retried name reservation : name server=http://<host>:50000/,". When you click Save Configuration, the pending items in the queue will be processed. The only problem we have left is that "after some time" the 2nd entry we just defined dissapears and we need to configure it again (and again and again...)
Kind regards,
Sigiswald

SQL Server cannot authenticate using Kerberos because the Service Principal Name (SPN) is missing, misplaced, or duplicated

We are getting this below alert message, while using SCOM 2012 R2. Anybody have any idea how to resolve this on the SQL box ?
Thx...
SQL Server cannot authenticate using Kerberos because the Service Principal Name (SPN) is missing, misplaced, or duplicated.
Service Account: NT Service\MSSQL$SQLEXPRESS
Missing SPNs:
Misplaced SPNs: MSSQLSvc/mysqlbox.com:SQLEXPRESS - sqldbadmin
Duplicate SPNs:

To Fix this issue, You can check below links
http://support.microsoft.com/kb/2443457/EN-US
http://www.scomgod.com/?p=155
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"Mai Ali | My blog:
Technical | Twitter:
Mai Ali

CO28: Unable to connect to Siebel Gateway Name Server

Hello.
I'm trying to install Siebel on a WinXP machine to familiarize myself with the Case Management module from Siebel. I have tried many times, installing and uninstalling software. I keep getting this error message when configuring a new Enterprise. "CO28: Unable to connect to Siebel Gateway Name Server".
I've shortened the hostname and removed dashes as prescribed in Siebel Bookshelf.
I've always made sure the ODBC System DSN is working and authenticating correclty.
Netstat shows gtwyns listening on 0.0.0.0:2320
What am I missing?????

Here's the log contents from sw_cfg_util.log:
2021 2009-05-21 12:52:03 0000-00-00 00:00:00 -0700 00000000 001 003f 0001 09 sw_cfg_util 2992 1704 C:\sba8123\siebsrvr\log\sw_cfg_util.log 8.1.1 [21112] ENU
GenericLog     GenericError     1     000000024a150bb0:0     2009-05-21 12:52:03     Error in transferring input values ,num of arrays incorrect 0, expected : 1
GenericLog     GenericError     1     000000024a150bb0:0     2009-05-21 12:52:03     TransferInputsToValues returned error:3611539 to SetControlValues
GenericLog     GenericError     1     0000031a4a150e34:0     2009-05-21 12:52:28     NSS - ErrCode 4597527 SysErr 0
GenericLog     GenericError     1     0000031b4a150e34:0     2009-05-21 12:52:29     NSS - ErrCode 4597527 SysErr 0
GenericLog     GenericError     1     0000031b4a150e34:0     2009-05-21 12:52:29     Validation failed : C028: Unable to connect to the Siebel Gateway Name Server 嗭粑୩୩୩୩୩୩୩
GenericLog     GenericError     1     0000031b4a150e34:0     2009-05-21 12:52:29     ValidateFailed for Gateway Name Server TCP/IP Port, error : C028: Unable to connect to the Siebel Gateway Name Server 嗭粑୩୩୩୩୩୩୩
GenericLog     GenericError     1     0000031b4a150e34:0     2009-05-21 13:18:49     Error in transferring input values ,num of arrays incorrect 0, expected : 1
GenericLog     GenericError     1     0000031b4a150e34:0     2009-05-21 13:18:49     TransferInputsToValues returned error:3611539 to SetControlValues
GenericLog     GenericError     1     0000031c4a150e34:0     2009-05-21 13:18:52     NSS - ErrCode 4597527 SysErr 0
GenericLog     GenericError     1     0000031c4a150e34:0     2009-05-21 13:18:52     Validation failed : C028: Unable to connect to the Siebel Gateway Name Server 嗭粑୩୩୩୩୩୩୩
GenericLog     GenericError     1     0000031c4a150e34:0     2009-05-21 13:18:52     ValidateFailed for Gateway Name Server TCP/IP Port, error : C028: Unable to connect to the Siebel Gateway Name Server 嗭粑୩୩୩୩୩୩୩

Name server problem on install

Hello,
just wondering if anyone can help - haven't had too much (very little) experience with solaris (or unix for that matter).
When installing Solaris 10 from cd (sparc) I get to the 'Confirm Information' screen, click confirm and it comes back with an error stating that 'The Name Server information entered is incorrect'.
The problem is that the NS's I entered are exactly the same as the NS's on my windows machine - also hooked up to the same router.
If I accept the supposed incorrect settings and continue the install everything completes ok - except the system can't resolve names. Here's the really strang bit - I can do an nslookup of www.google.com no problem (returning from the first NS entered) but can't do a lookup of anything else.
The DNS's are external to my network (supplied by ISP) and the connection is ADSL.
Other options set in setup : DHCP - no (Static public subnetted IP), Kerberos - no, Search Domain : none, Route :specified, ipv6 - no.
(during setup)The Solaris Install Console shows:
Completing system identification...
runCmd error in /usr/sbin/sysidput with output:
Unable to run cmd: /usr/sbin/sysidput
Any help would be much appreciated. (and apologies if this is something I should have picked up on in the docs - I did read as much as I could and I have searched the net for an answer to this)(I have also posted this on the install forum, but got no replies)
Gar

You should provide a bit more info on how your network is setup. How are you connected to the ADSL? Does your router have DHCP?
The DNS information you fill in during install is not ment for external DNS servers it's your local networks DNS server.
It is used to verify that the hostname you entered exists in the network/domain.
You could of course fill in external dns servers, but you'd allways end up with a 'can't resolv'. Simply because YOUR hostname does not excist on the external DNS server.
As Codename47 suggests, try not filling in a dns server. (use the hosts file instead)
Just an extra tip that appearantly some don't seems to know:
you don't have to reinstall to get it sorted. The command 'sys-unconfig' will force a reboot and guide you through the exact same configuration menu you had during install. Updating all locale, X and network settings along the way.
The nice thing is you can do it over again till you get it right and fully understand what it all means and changes.

How to add tns entry in names server

Hi,
Can anyone tell us, How to add tns entry in names server
Thanks

In the Net Manager utility, in the left-hand pane left click Oracle Names Servers, left click on your nameserver.
Click the "+" button in the upper left, that should be enough to get you started- sorry, all our 9i installs have gone away, can't exactly recall the nix X gui version of client program, but I think* its netmgr, should be in OH/bin.
If you're running a java OEM console that cames with 9i clients, Net Manager is available on that little Butler tab.
And for the command line version, running the namesctl utility- you can save a tns entry with the connect string and run it in a file, just like sqlplus, with an @filename:
vi newtns.txt
register newtns -d (DESCRIPTION=(ADDRESS_LIST=...(SERVICE_NAME=NEWTNS.MYCO)))
$ namesctl
@newtns.txt
query newtns *
reload -- nameserver sync
query newtns *
exit
$ Edited by: clcarter on Jul 7, 2011 3:26 PM
added cmdline version

Siebel Gateway Name Server configuration error

Hi,
I installed Siebel 8.1.1.10 in Oracle Enterprise Linux 5.9. And use following command lines to configure Siebel Gateway Name Server.
/opt/siebel/8.1.1.0.0/ses/gtwysrvr/cfgenv.sh
/opt/siebel/8.1.1.0.0/ses/config/config.sh -mode enterprise
After some steps, the Configuration Wizard prompted 'Siebel Configuration Wizard failed with error. Please see the log files for details'.

You can try to use locate and search for: *.log
Tips For Linux - How to find files in Linux using 'locate'

Final Cut Server (FCSvr) missing the Edit Proxies Device in the Advanced Administration Pane.

Final Cut Server (FCSvr) missing the Edit Proxies Device in the Advanced Administration Pane.
If for any reason an Admin has mistakenly or purposely deleted the Edit Proxies device
from the FCSvr Java Admin, and you'd like to restore connective to it following the instructions below.
Note verify these symptoms, open the FCSvr Java Admin, Go to Preferences and the Proxies Pane and inspect
If the field and drop down for Edit Proxies is missing please backup your FCSvr DB manually and following the steps below to restore connectivity.
1. From the Terminal from the following command
 cd /Library/Application\ Support/Final\ Cut\ Server/Final\ Cut\ Server.bundle/Contents/MacOS/
2. Next run the following command
 ./fcsvr_client getmd --xml /prefs/0 > ~/Desktop/prefs0.xml
This will output a XML file containing the Final Cut Server Global Preferences to the Desktop folder of the currently logged in user.
3. Using for favorite XML Text Editor (mine is TextMate) open the file that was output
4. Notice the XML element and attribute values between lines 29 and 31
<value id="PROXY_CLIP_EDIT_DEVICE">
 <address>/dev/3</address>
</value>
5. From the command line run the following command to determine the Device ID for you Edit Proxies device
./fcsvr_client search /dev
You should get an output similar to what's below.
Address DEVICE_NAME DEVICE_TYPE
/dev/20 Edit Proxies contentbase
/dev/9 MEDIA filesystem
/dev/1 Proxies contentbase
/dev/2 Version contentbase
Record the new Device id for the Edit Proxies device.
6. Open up the file /Desktop/prefs0.xml and XML attribute in line 29
 <address>/dev/20</address>
to the value of the Edit Proxies from step 6.
7. Save the /Desktop/prefs0.xml
8. From the command line run the following command
sudo ./fcsvr_client setmd /prefs/0 --xml ~/Desktop/prefs0.xml
enter you admin password if prompted.
9. Close and reopen the FCSvr Java Admin, Go to Preferences and Proxies and inspect
The field and dropdown should reappear.
If for some reason this didn't work, feel free to contact me offline.
Nicholas Stokes
[email protected]

H.264 is a puzzling choice of codec for edit proxies. H.264 is not an edit-friendly codec since it is a complex long-GOP structure and will require a ton of rendering just to play back the timeline. ProRES 422 Proxy would be a much better choice for editing. I'm afraid I can't account for the differences between Compressor and FCServer in this case, but my gut tells me the non-I-frame codec you are trying to use for edit proxies might have something to do with it. Maybe for an edit-proxy workflow to operate properly on the server-side the codec must be I-frame? Is there any reason you do not want to use ProRES 422 Proxy? They are about 1/3 the footprint of 720p24 DVCPRO-HD, which is already very efficient. For that frame rate and frame size they would be roughly half the heft of good ol' DV25.
So my answer to all three questions would be to try ProRES 422 Proxy for your edit proxies and see if everything lines up.

Role Name Server defined in SLD but no CimomURL maintained

Hello gurus!
We have a problem with our NWDI setup.
What I want to do is to update an existing track DFODEV02 with the software package EP-RUNTIME.
I synchronize with the SLD. However when I try to save, I get the following error:
"SLD (URL http://<NWDI_server>:<port>)
server exception: Invalid Name Server null - Check SLD configuration -> Role
Name Server defined in SLD but no CimomURL maintained."
I am not familiar with the customizing for this but I have looked into a couple of customizing steps related to Data Supplier:
1) Under administration on SLD I see the following:
Update Namespaces is marked as sld/active; but
Update Other SLDs is an empty list.
2) From the configuration on NWA:
Target URL: <RuntimeSLD_server>/sld/ds
Both 'Automatic send' and 'success' are both "true".
Hope that you can guide us on the right “track”
In advance, thank you very much!
Best regards,
Elias

Hi Elias,
1) Under administration on SLD I see the following:
Update Namespaces is marked as sld/active; but
Update Other SLDs is an empty list.
This is something else, your error message is not about this one.
What you need to make sure is that you have a name server defined.
You can check it in various ways:
A). go to CMS -- Track Data -- select the track in question -- tab Build Variants -- Display/Download the Development Configuration --> This will be an XML file. If you see a tag "sld-nameserver" then you are ok, however I assume this tag is missing or points to a wrong SLD in your case.
B)
Go to the initial page of the SLD.
2. Choose Landscapes.
3. Choose New Landscape…
4. In the page that appears, select the landscape type NWDI System.
5. Specify NWDI as the name of the landscape. Choose Create.
The new landscape is displayed.
6. Select the new landscape.
You see the details about the landscape.
7. Choose Systems and then choose Add System to Landscape.
8. Choose the hosted system type System Landscape Directory. Choose OK.
You see the installed SLD.
9. Select the SLD.
The details view appears.
10. Select the roles Landscape Server and Name Server and save your changes.
The name server is now known to the NWDI and can be used there. Only now can you create valid development configurations.
Could you please confirm this way whether you have a name server specified and that points to the correct SLD ?
I hope this guides you to the right "track"
Regards,
Ervin

Unable to connect to Gateway Name Server while config Siebel Server

I installed Siebel 8.1.1.11.0 on RHEL 32-bit. I did configuration as following.
Install 32-bit Oracle Client and config TNS.
Install and config Gateway and Enterprise.
Install Siebel Database.
Use stop_ns, start_ns and list_ns to restart and ensure Gateway running.
Run CreateSiebSrvrEnvScript to generate Env file.
Modify /siebel/8.1.1.11.0/ses/siebsrvr/siebenv.sh. Change ODBCINI=/siebel/8.1.1.11.0/ses/gtwysrvr/sys/.odbc.ini.
Source siebenv.sh.
export LD_LIBRARY_PATH=$LD_LIBRARY_PATH:/home/oracle/product/11.2.0/client_1/lib
Config Siebel Server. While enter info of Gateway, enter SADMIN as account, rhel (configed in /etc/sysconfig) as host name and port = 2320. Then it prompt "Unable to connect to the Siebel Gateway Name Server".
Any step missing to config it?
Thanks

The siebenv.sh file located in the Gateway directory from a 8.1.1.11 installation doesn't have the enviromentt variable SIEBEL_UNIXUNICODE_DB, which i do have in the siebenv.sh from my 8.1.1.0 installation. Add the following line to the siebenv.sh located in the gateway directory (/siebel/8.1.1.11.0/ses/gtwysrvr in my installation):
SIEBEL_UNIXUNICODE_DB=ORACLE; export SIEBEL_UNIXUNICODE_DB
Be sure that this variable is set BEFORE you start the gateway and everything should work.
PS- You also need the Oracle enviroment varibles set before you start the gateway. ORACLE_HOME should be pointing to your 32bit client.
Cheers!

Configuring Siebel Gateway Name Server on Linux 64 bit OS

Hello Siebel Experts,
I am currently installing Siebel 8.1.1.11 on a Linux 64-bit machine. After successfully completing the installation steps, I am proceeding with the configuring the server and its components.
I am starting with the configuration of Siebel Gateway Name Server as per the instructions mentioned on the url:
Bookshelf v8.1/8.2: Configuring the Siebel Enterprise
I completed steps 1 and 2 and started executing step 3: Start the Siebel Enterprise Configuration Wizard.
I provided all the necessary information till the summary information is displayed.
However when I click next, it immediately gives an error.
>>Siebel Configuration Wizard fails with error. Please check the log files for details.
I searched for the log file in $SIEBEL_ROOT/cfgtoollogs/cfg/config_<date-time>.log
However there is no error information in this log file. It contains just INFO, SECTION, STEP or ATTRIBUTE mappings/values.
I could not find any .err file in this directory. Can you please let us know how to identify the error and debug this issue?
Thanks in advance.
Regards,
Sadath

Hi
Thanks for your inputs.
I have executed the said command and captured the output in the below file:
https://docs.google.com/file/d/0By7-5z2zbQo9MUd5ek1mdTh1SU9yUzlZRzc2eDlFZFNrczR3
I also executed env command and following is the output:
[telkom@ucm1 bin]$ ./evt
Running checks defined in file [evt.ini]. Please wait..
▒1990, 2006, Oracle. All rights reserved. The Programs (which include both the software and documentation) contain proprietary information; they are provided under a license agreement containing restrictions on use and disclosure and are also protected by copyright, patent, and other intellectual and industrial property laws. Reverse engineering, disassembly, or decompilation of the Programs, except to the extent required to obtain interoperability with other independently created software or as specified by law, is prohibited.
Environment Verification Summary Report for [ucm1.cx.dev.telkom.co.id]
Report Run by [telkom] on [Thu Jul 17 12:30:12 2014]
Installed Version [NOT DETECTED] Installed Build [NOT DETECTED]
Running a [8.1.1.9] version validation with [VAN] flavor
Total Checks : 4
Checks Passed : 1
Checks Failed : 3 (0 critical failures, 3 warnings)
Checks Skipped: 0
Critical Failures:
Complete list of checks:
Environment Settings
The highest Operating System that we have certified is 2.6.32-100.37.1.el6 - the current version you are running is 3.8.13-35.1.2.el6uek.x86_64
The current value of SIEBEL_OSD_LATCH is not defined
The current value of SIEBEL_OSD_NLATCH is not defined
Environment variable SIEBEL_MEMORY_ALLOCATOR has correctly not been defined
This exe file was created with the evaluation version of Perl2Exe.
For more information visit http://www.indigostar.com
(The full version does not display this message with a 2 second delay.)
[telkom@ucm1 bin]$
Thanks,
Sadath

C028: Unable to connect to siebel gatway name server"

Hi,
We are using Oracle enterprise linux 6.3 version OS for siebel 8.1.1.7 siebel installation on oracle database.
I have installed the siebel gateway name server, but while installing enterise, it is erroring out during the gateway name server authentication.
Points ot note. checked all the below options
1. db connectivity is working fine wt SADMIN/SADMIN user. able to conect using sqlplus
2. able to ping the gateway port using netstat.
3. the oracle client is a 32 bit client.
Also there is gateway.cfg file missing from gtwysrvr/bin. but the gateway service is up and running and the process is pointing to the gateway.cfg in the bin file. .
Please suggest.
Thanks,
Vinod.

Vinod,
Check if Doc ID 1391312.1 on support.oracle.com is helpful.
Thanks,
Wilson

Siebel Gateway Name Server Configuration Wizard returns "Execution failed"

Hi,
I am installing Siebel 8.1.1.1 on Linux platform and now having problem while trying to configure Siebel Gateway Name Server.
Steps done:
1) DB instance prepared
2) Created Siebel installation image
3) Installed Siebel server and configured Gateway name server (the wizard started automatically as part of the installation). Skip configuration of Enterprise and SWSE Logical profile
4) Ran DB Configuration Wizard for the primary language - successfully. Import repository-add language - successfully.
5) Trying to Wizard "Configure Enterprise" - failed with "Execution failed"
Here I thought that probably Gateway Nameserver was not configured and decided to remove the Gateway and create it from scratch.
Unfortunately this time the Gateway configuration failed. Also with message"Execution failed"
Here are the errors I got in the log files sw_cfg_util*.log
<EF><BB><BF>2021 2012-01-25 16:14:56 2012-01-25 16:14:56 +0200 00000002 001 003f 0001 09 sw_cfg_util 17234 -1215752512 /OraSSO_tstcol/siebapp/server/siebsrvr/log/sw_cfg_util.log 8.1.1 [21111] ENU
GenericLog GenericError 1 000000024f204352:0 2012-01-25 16:14:56 (svrconfig.cpp (2465) err=3023557 sys=0) SBL-CSO-08901: The required arguments are not specified.
GenericLog GenericError 1 000000034f20432e:0 2012-01-25 16:14:56 Executing step: CreateGateway
GenericLog GenericError 1 000000034f20432e:0 2012-01-25 16:14:58 Step CreateGateway: failed to run program %%SiebelRoot%%%%OSDirSeparator%%bin%%OSDirSeparator%%srvrcfg with cmdline -u nouser -p nopassword -r %%SiebelRoot%% -g %%SiebelRoot%%%%OSDirSeparator%%sys%%OSDirSeparator%%siebns.dat::NSFILE: -r %%SiebelRoot%% -a gateway -l %%PrimaryLanguage%% -i %%SiebelRoot%%%%OSDirSeparator%%admin%%OSDirSeparator%%gtwydefs.dat
GenericLog GenericError 1 000000034f20432e:0 2012-01-25 16:14:58 Failed during Execution, err: 5500044
Does anybody know what is the reason?
Searching in Metalink and Google were fruitless..
Thank you in advance.

Just in case anybody bumps in this thread:
The problem in my case was solved according with Oracle Note "Delete and create the "Siebel Server" via Configuration Wizard on Linux, it failed. [ID 880562.1]"
Applies to:
+Siebel CRM - Version: 8.1.1 SIA [21111] and later [Release: V8 and later ]+
Linux x86
Symptoms
Delete the "Siebel Server" once and then create a new "Siebel Server" via Siebel Server Configuration Wizard on Linux, it failed with message "Execution Failed".
The error on sw_cfg_util_xx.log is as follows,
GenericLog GenericError 1 0000ce524a3a1bd2:0 2009-06-19 10:18:33 Executing step: AddSrvrRegistryEntry
GenericLog GenericError 1 0000ce524a3a1bd2:0 2009-06-19 10:18:35 Step AddSrvrRegistryEntry: failed to run program %%SiebelRoot%%%%OSDirSeparator%%bin%%OSDirSeparator%%siebctl with cmdline -r %%SiebelRoot%% -q -S siebsrvr -i "%%SiebelEnterprise%%:%%SiebelServer%%" -a -g "-g %%SiebelGateway%% -e %%SiebelEnterprise%% -s %%SiebelServer%% -u %%Username%%" -e %%Password%%
GenericLog GenericError 1 0000ce524a3a1bd2:0 2009-06-19 10:18:35 Failed during Execution, err: 5500044
Reproduce steps:
- confirm that siebel server was created before, and is stopping.
- create sh env and enter the following command to remove the Siebel Server.
+$ cd $(SiebelServerRoot)+
+$ . ./cfgenv.sh+
+$ cd $(SiebelServerRoot)/bin+
+$ ./ssincfgw+
- select "3 - Remove Existing Configuration".
- complete the configuration wizard.
- enter the following command to create the Siebel Server.
+$ cd $(SiebelServerRoot)+
+$ . ./cfgenv.sh+
+$ cd $(SiebelServerRoot)/bin+
+$ ./ssincfgw+
- select "1 - Create New Configuration".
- continue inputs to finish and execute the configration.
+==> you'll find "Execution Failed".+
Cause
AddSrvrRegistryEntry section shown in the log is the command for registering the Windows Service, and it is no need to execute on Linux env. However, it is executed and it failied.
Solution
You can do either of follows,
+(1) Uninstall and Install the Siebel Server again.+
+(2) The section to execute the Windows registeration command is specified on $(SiebelServerRoot)/admin/common.scm, line 2475-2477.+
+[Step]+
Name = AddSrvrRegistryEntry
Type = RunProg %%SiebelRoot%%%%OSDirSeparator%%bin%%OSDirSeparator%%siebctl ' -r %%SiebelRoot%% -q -S siebsrvr -i "%%SiebelEnterprise%%:%%SiebelServer%%" -a -g "-g %%SiebelGateway%% -e %%SiebelEnterprise%% -s %%SiebelServer%% -u %%Username%%" -e %%Password%% '
So, delete the AddSrvrRegistryEntry section from common.scm, and execute Configuration Wizard again.
Edited by: mmango on Jan 31, 2012 12:21 AM

SR520 - no ip name-server command missed

Similar Messages

Maybe you are looking for