Star Services on Analogue line

Any idea whether there is a dial plan available that allows star services ( *21* , #21# etc) to work on a UC320 as well as my modified dial plan for 166?
Cisco really should introduce the ability to allow users to edit their own dial plans - seems logical?
Thanks.
...Jon.

Hi Jon,
Yes, we have a PMF which adds dial plans to enable/disable call redirection. And there is a UK region pack which adds 166 service dial plan. Please send me an email to [email protected] I will reply you with the PMF and region pack.
Best regards,
Wendy

Similar Messages

Dialling plan that supports star services for the UK

Wendy has sent me a dialling play that supporrts *21, but I need a UK dialling plan that supports all fo the UK star services as below - Can anyone help please?
SET ANONYMOUS CALL REJECTION *227#
CHECK ACR *#227#
CANCEL ACR #227#
Call Divert on all calls
SET CALL DIVERSION * 21 * [phone number] #
CHECK CALL DIVERSION * # 21 #
CANCEL CALL DIVERSION # 21 #
Call Divert on no reply
SET DIVERSION ON NO REPLY * 61 * [phone number] #
CHECK DIVERSION ON NO REPLY * # 61 #
CANCEL DIVERSION ON NO REPLY # 61 #
Divert on no reply: *61*number*wait# == (Extra System Y facility only - does not work on 410567 as of Dec 2011)
Wait is two digit time in seconds (05 to 60) before redirection takes place.
Call Divert on busy
SET DIVERSION ON BUSY * 67 * [phone number] #
CHECK DIVERSION ON BUSY * # 67 #
CANCEL DIVERSION ON BUSY # 67 #
Call Divert on no reply or busy
SET DIVERSION ON NO REPLY & BUSY * 66 * [phone number] #
CHECK DIVERSION ON NO REPLY & BUSY * # 66 #
CANCEL DIVERSION ON NO REPLY & BUSY # 66 #
Call Minder (Voicemail)
CALL MINDER SERVICE 1571
Call Waiting
SET CALL WAITING * 43 #
CHECK CALL WAITING * # 43 #
CANCEL CALL WAITING # 43 #
Caller Display
SET CALLER DISPLAY DATA ON *234#
CHECK CALLER DISPLAY DATA *#234#
CANCEL CALLER DISPLAY DATA #234#
Caller ID
WITHHOLD CALLER ID 141 [phone number]
RELEASE CALLER ID 1470 [phone number]
CALLER RETURN 1471
ERASES LAST NUMBER GIVEN ON CALLER RETURN 1475
BLOCK LAST CALL ANSWERED WITH CHOOSE TO REFUSE 14258 [PIN] **
ADD TO LIST OF BLOCKED NUMBERS WITH CHOOSE TO REFUSE 14258 [phone number] #
Charge Advice
SET CHARGE ADVICE (BEFORE A CALL) * 40 * [phone number] #
SET CHARGE ADVICE (FOR ALL CALLS) * 411 #
CHECK CHARGE ADVICE *# 411 #
CANCEL CHARGE ADVICE # 411 #
Choose to Refuse
BLOCK LAST CALL ANSWERED WITH CHOOSE TO REFUSE 14258 [PIN] **
ADD TO LIST OF BLOCKED NUMBERS WITH CHOOSE TO REFUSE 14258 [phone number] #
I
ncoming Call Barring
SET INCOMING CALL BARRING * 261 #
CHECK INCOMING CALL BARRING * # 261 #
CANCEL INCOMING CALL BARRING # 261 #
Miscellaneous
CHECK WHICH SERVICES ARE ACTIVE * # 001 #
BT LINE TEST & RINGBACK FACILITY 17070
REDIAL LAST NUMBER DIALLED **0
Outgoing Call Barring
SET OUTGOING CALL BARRING * 34 option #
CHECK OUTGOING CALL BARRING * # 34 #
CANCEL OUTGOING CALL BARRING # 34 option * [PIN] #
Reminder Call Service
SET REMINDER CALL (using 24 hour clock with 4 digits) * 55 * [time] #
CHECK REMINDER CALL * # 55 #
CANCEL REMINDER CALL # 55 #
SET REGULAR REMINDER CALL * 56 * [time] * [day option] #
CHECK ALL REGULAR REMINDER CALL * # 56 #
CANCEL A REGULAR REMINDER CALL # 56 * [time] * [day option] #
CANCEL ALL REGULAR REMINDER CALLS # 56 #
Day options numbers: Monday - 1, Tuesday - 2, Wednesday - 3, Thursday - 4, Friday - 5, Saturday - 6, Sunday - 7, Monday - Friday: 8 Every Day - 9.
Remote (Smart) Call Divert on all calls
SET REMOTE CALL DIVERT ON ALL CALLS * 44 * [PIN] * [your full phone number] * [number to divert to] #
CHECK REMOTE CALL DIVERT ON ALL CALLS # 44 * [PIN] * [your full phone number] #
CANCEL REMOTE CALL DIVERT ON ALL CALLS * # 44 * [PIN] * [your full phone number] #
Remote (Smart) Call Divert on no reply
SET REMOTE CALL DIVERT ON NO REPLY * 64 * [PIN] * [your full phone number] * [phone number to divert to] #
CHECK REMOTE CALL DIVERT ON NO REPLY # 64 * [PIN] * [your full phone number] #
CANCEL REMOTE CALL DIVERT ON NO REPLY * # 64 * [PIN] * [your full phone number] #
Remote (Smart) Call Divert on busy
SET REMOTE CALL DIVERT ON BUSY * 65 * [PIN] * [your full phone number] * [phone number to divert to] #
CHECK REMOTE CALL DIVERT ON BUSY # 65 * [PIN] * [your full phone number] #
CANCEL REMOTE CALL DIVERT ON BUSY * # 65 * [PIN] * [your full phone number] #
Ringback
SET RINGBACK [phone number] 5
CHECK RINGBACK *#37#
CANCEL RINGBACK #37#
SET RING BACK INHIBIT *02*37#
CHECK RING BACK INHIBIT *#02*37#
CANCEL RING BACK INHIBIT #02*37#
CALL ROUTING VIA BT
(when using another provider) 1280

Hi Jon,
After thorough discusiion with engineering team and marketing team, we have decided to support most star services you requested except the following items. I have created a PMF for it. Please send me an email at [email protected]. I will reply you with the PMF.
Call Minder (Voicemail)
CALL MINDER SERVICE 1571
Call Waiting
SET CALL WAITING * 43 #
CHECK CALL WAITING * # 43 #
CANCEL CALL WAITING # 43 #
Caller ID
WITHHOLD CALLER ID 141    [phone number]
RELEASE CALLER ID 1470 [phone number]
CALLER RETURN 1471
ERASES LAST NUMBER GIVEN ON CALLER RETURN 1475
BLOCK LAST CALL ANSWERED WITH CHOOSE TO REFUSE 14258 [PIN] **
ADD TO LIST OF BLOCKED NUMBERS WITH CHOOSE TO REFUSE 14258 [phone number] #
Choose to Refuse
BLOCK LAST CALL ANSWERED WITH CHOOSE TO REFUSE 14258 [PIN] **
ADD TO LIST OF BLOCKED NUMBERS WITH CHOOSE TO REFUSE 14258 [phone number] #
Incoming Call Barring
SET INCOMING CALL BARRING    * 261 #
CHECK INCOMING CALL BARRING    * # 261 #
CANCEL INCOMING CALL BARRING    # 261 #
REDIAL LAST NUMBER DIALLED **0
Outgoing Call Barring
SET OUTGOING CALL BARRING * 34 option #
CHECK OUTGOING CALL BARRING    * # 34 #
CANCEL OUTGOING CALL BARRING    # 34 option * [PIN] #
Reminder Call Service
SET REMINDER CALL (using 24 hour clock with 4 digits)    * 55 * [time] #
CHECK REMINDER CALL * # 55 #
CANCEL REMINDER CALL # 55 #
SET REGULAR REMINDER CALL    * 56 * [time] * [day option] #
CHECK ALL REGULAR REMINDER CALL    * # 56 #
CANCEL A REGULAR REMINDER CALL    # 56 * [time] * [day option] #
CANCEL ALL REGULAR REMINDER CALLS    # 56 #
Day options numbers: Monday - 1, Tuesday - 2, Wednesday - 3, Thursday - 4, Friday - 5, Saturday - 6, Sunday - 7, Monday - Friday: 8 Every Day - 9.
Ringback
SET RINGBACK [phone number] 5
CHECK RINGBACK   *#37#
CANCEL RINGBACK #37#
SET RING BACK INHIBIT *02*37#
CHECK RING BACK INHIBIT *#02*37#
CANCEL RING BACK INHIBIT #02*37#
Best regards,
Wendy

Service Contract header, line level and party data report.

Using 11.5.9.
In Service Contracts Module, trying to create a query that extracts header data, party data (role and name) and the name of the service from the lines/account tab, ie Full Service, Gold Service etc...
Created query that retrieve Service Contract header and party data, but when I try to join to mtl_system_items_b, I am getting a product description instead of the name of the service. I also include code below this that pulls in the lines from the lines/account tab which captures line 1.1 and has the correct service name. Note this code does not have the header data and party data built into it, but I am willing to modify either piece of code to create the need join and get the data returned.
SELECT
distinct (okhb.contract_number)     contract_number,
nvl(okhb.contract_number_modifier,'-') contract_modifier,
okhb.sts_code,
okhb.start_date     start_date,
okhb.end_date          end_date,
okprb.rle_code ROLE,
msib.description,
(msib.segment1) item_number,
hp.party_name
FROM
hz_party_sites ps,
hz_party_sites ps9,
hz_locations l,
hz_locations l9,
hz_cust_acct_sites_all ca,
hz_cust_acct_sites_all ca9,
hz_cust_site_uses_all cs,
hz_cust_site_uses_all cs9,
hz_parties hp,
hz_parties hp9,
okc_rules_b orb,
okc_rules_b orb9,
okc_rule_groups_b ogb,
okc_k_headers_b okhb,
okc_k_party_roles_b okprb,
okc_k_lines_b oklb,
ra_customer_Trx_all rcta,
mtl_system_items_b msib
WHERE
PS.LOCATION_ID = L.LOCATION_ID AND
ps9.location_id = l9.location_id and
L.CONTENT_SOURCE_TYPE = 'USER_ENTERED' AND
l9.content_source_type = 'USER_ENTERED' and
PS.PARTY_SITE_ID = CA.PARTY_SITE_ID AND
ps9.party_site_id = ca9.party_site_id and
CA.CUST_ACCT_SITE_ID = CS.CUST_ACCT_SITE_ID and
ca9.cust_acct_site_id = cs9.cust_acct_site_id and
ps9.party_id = hp9.party_id and
ps.party_id = hp.party_id and
cs.site_use_id=orb.object1_id1 and
cs9.site_use_id = orb9.object1_id1 and
orb.jtot_object1_code in ('OKX_SHIPTO'/*,'OKX_BILLTO'*/) and
orb9.jtot_object1_code = 'OKX_BILLTO' and
orb.rgp_id = ogb.id and
orb9.rgp_id = ogb.id and
okhb.id = okprb.chr_id and
msib.inventory_item_id = orb.object1_id1 and
okhb.contract_number = rcta.interface_header_attribute1 and
nvl(okhb.contract_number_modifier,'-') = nvl(rcta.interface_header_attribute2,0) and
ogb.chr_id = okhb.id and
okhb.sts_code = 'ACTIVE' and
okhb.contract_number in ('VO-7001','VO-7078') and
okprb.rle_code in ('CUSTOMER','END_USER')
--oklb.line_number||'.'||oklbs.line_number = '1.1'
order by okhb.contract_number;
select
     to_char(oklb.line_number)||'.'||to_char(oklbs.line_number) subline_number,
okhb.contract_number,
     okhb.sts_code,
(msi.segment1) item_number,
     msi.description,
     okcis.number_of_items,
round(months_between(element.date_completed , element.date_start))     billable_days,
     oklbs.start_date          start_date,
     oklbs.end_date          end_date,
     to_date(oklbs.attribute1, 'YYYY/MM/DD HH24:MI:SS')          warranty_start_date,
     to_date(oklbs.attribute2, 'YYYY/MM/DD HH24:MI:SS')          warranty_end_date,
     oklbs.attribute4 sales_order
from oks_level_elements_v element,
okc_rules_v rule,
okc_rule_groups_v grp,
oks_bill_cont_lines_v      obcl,
     okc_k_lines_v          oklbs,
     okc_k_items_v               okcis,
     mtl_system_items_vl     msi,
     okc_k_items_v               okci,
     okc_k_lines_v           oklb,
     okc_k_headers_v          okhb,
OKS_BILL_TRANSACTIONS_V obtrx
where trunc(element.date_start) = trunc(obcl.date_billed_from) and
rule.id = element.rul_id and
rule.rgp_id = grp.id and
grp.rgp_type = 'KRG' and
grp.rgd_code = 'SVC_K' and
grp.cle_id = oklbs.id and
oklbs.cle_id     = oklb.id      and
     oklbs.lse_id     <> '2'      and
okhb.sts_code = 'ACTIVE' and
     msi.inventory_item_id = okci.object1_id1 and
     msi.organization_id = 3      and
     okcis.cle_id          = oklbs.id and
     okci.cle_id          = oklb.id and
     obcl.cle_id           = oklb.id      and
     oklb.chr_id           = okhb.id      and
     obcl.btn_id = obtrx.id and
     okhb.contract_number like 'VO-7078' and
oklb.line_number||'.'||oklbs.line_number = '1.1'
order by okhb.contract_number, to_number(oklb.line_number), to_number(oklbs.line_number), oklbs.id;
Code that pulls in the correct description as seen at line level in Service Contracts Module.
OUTPUT of this query
CONTRACT_NUMBER     STS_CODE     ITEM_NUMBER     DESCRIPTION
XX-XXXX     ACTIVE     FULL SERVICE     FULL SERVICE

I guess you are looking for coverage name. You need to add two more table to join with items like as in
select inventory_item_id,a.name,a.item_description from mtl_system_Items_b c,okc_k_lines_tl a,okc_k_lines_b b
where organization_id=<organization_id>
and contract_item_type_code in ('SERVICE','WARRANTY')
and a.id=b.id
and b.chr_id=-1
and coverage_schedule_id=b.id;
Thanks
Nagamohan

Analogue line input on SB Live!

Hi,
I am trying to sample my old vinyl record collection using my Sound Blaster Li've! PCI (think that was the model - it was the original (not Value) version of the card with the seperate header for the coaxial digital and MIDI I/O).
Unfortunately, I get severe clipping regardless of the recording volume on the Volume Control panel. I know that my photo pre-amp is capable of high voltage outputs and therefore wondered if anyone was aware of the sensitivity of the analogue line input in volts of this particular model?
Many thanks.
Regards,
Paul.

paush wrote:
Hi, I am trying to sample my old vinyl record collection using my Sound Blaster Li've! PCI (think that was the model - it was the original (not Value) version of the card with the seperate header for the coaxial digital and MIDI I/O). Unfortunately, I get severe clipping regardless of the recording volume on the Volume Control panel. I know that my photo pre-amp is capable of high voltage outputs and therefore wondered if anyone was aware of the sensitivity of the analogue line input in volts of this particular model? Many thanks.
Regards, Paul.
If your pre-amp is a phono pre-amp (with RIAA in-build), I suppose it's not the culprit for clipping.
How have you set the recording and source (input) levels on Volume Control and Recording Control?
Try adjust the recording level by the 'hights' (loudest outputs) of the record (you know those recordings so you can easily find those places (or you can look on vinyls surface where the darkest areas are --> loudest outputs)).
jutapaMessage Edited by jutapa on 0-23-2006 :38 PM

Service keeps repeating line training.

Hi all,
For some reason my line keeps going into line training mode.
I was upgraded to ADSL2+ on 9 Aug 2010. Line training, as expected, completed after 10 days and my line settled to an acceptable 15Mb/1Mb Down/Up. Fantastic.
I noticed during line training it was operating in Fastpath mode, and once training was complete it switched to Interleave. Once again as expected and no problem there.
Five days after line training comleted I noticed that my line had gone back into Fastpath mode and the typical daily change in speed and noise margin experienced during line training seemed to be happening again. Once again I watched it go through it's 10 day cycle and finally settle to 15Mb/1Mb Down/Up and change back to Interleave. Ok, just an anomaly I thought, service is still fantastic, not worried.
Today, about 5/6 days after the last line training phase I noticed my line has once again gone back to Fastpath mode and the typical pattern of line training seems to have started again.
Is this going to be a neverending cycle? I hope not, as the line training phase is not the most stable situation to be in, as the loss of synchronisation causes me to have to manually reconnect via my router in order to pick up the new IP address.
Anyone know what could cause this repeated cycle of line training?
My line attenuation (14db Down / 3 db Up) and noise margin (3db Down / 6 db Up) seem to be excellent and are not a problem.
Any help would be appreciated. Thank you.

Hi Campotech,
It's strange that your interleaving mode keeps changing - if you could drop me an email I'll see what's going on. Click on my profile to get our address, I'll need your forum username and BT account or telephone number.
Thanks,
Stephanie
Stephanie
BTCare Community Manager
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post. If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Service PO sub line items not appearing in PO print out

Hi,
Service PO line items under item details are not appearing on print out...
Where are they stored ..means in which table?
Regards

Hi SSingh,
Has this problem been solved? we have a similar problem here --- after upgrading from 4.6c to ECC6.0, we found that the service PO line items are not being shown in the PO printout. This happens for items that have been marked 'delivery complete'.
How do we get the service lines to print out again? Appreciate any help out there!

Unable to restart the Microsoft Software Protection Platform service from command line - Win81 MS Office 2013 SP1

I'm unable to restart the Microsoft Software Protection Platform service on a Windows 8.1 laptop for MS Office 2013 SP1 (32-bit) using the following command:
cscript ospp.vbs /osppsvcrestart (issued from C:\Program Files (x86)\Microsoft Office\Office15)
When this is run, a window appears with the title ospp.vbs and the text "Error: The Software Protection Platform service is not installed"
I verified that the service is installed in services.msc, and was able to manually stop and restart the SPP service in the Services console without issue.
The command runs correctly when restarting the MS Office 2013 SPP on Windows 7 devices.
Has anyone else seen this or have a solution for it?
The reason that I am attempting to restart the service from the command line is because this command is part of a script to change the KMS server IP Address used by OSPP prior to software activation.
The only other options that I have at this time is to ask the users to reboot, or manually force a reboot. This is both time consuming and disruptive to the users.
The Fix It tool to remove MS Office 2013 was run, and the MS Office 2013 software was successfully reinstalled after a reboot. The software was successfully activated. When the command was run, it produced the same exact error.

Hi,
I am able to reproduce this on my own machine, but in my case, I don't see the specific service running in the Services console.
I would like first confirm that whether you've the right service running on your Windows 8.1 system. The display name of this service should be "Office Software Protection Platform", service name is "osppsvc".
You can also check this by going to below path where you should see the executable file (OSPPSVC.EXE) if the service is installed on your system (in my case, the folder is empty):
C:\Program Files\Common Files\Microsoft Shared\OfficeSoftwareProtectionPlatform
Regards,
Ethan Hua
TechNet Community Support
It's recommended to download and install
Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
programs.
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected]

No Customer Service with Phone Line

I requested a transfer of phone service over a month ago. No service, yet. Two technicians have come out and diagnosed the problem as a Foreign Exchange issue stemming from a transfer of service. I called the customer service line on 3 different occassions today, they hung up on me three times. No explanation given. Who do i call?

We sent you a message on our private support board to assist you and we did not receive a response. Please repost the issue if you are still experiencing a problem so that we may assist you. Tonya C.

What does it take to get a VZW Customer Service Rep to call you back?? READY TO CANCEL SERVICE OF 4 LINES!

Has anyone else had problems with VZW customer service? I have been lied to repeatedly and am on the verge of terminating my contracts. To begin, I sent my daughters, who are authorized users, into the store - which is 40 minutes from my house- to upgrade and renew 2 lines. I called Apple to upgrade initially, but my account has a corporate discount, so they were unable to upgrade my lines of service. I called the closest VZW store, again 40 minutes away, spoke with the sales associate DUSTIN. I told DUSTIN exactly what I wanted and advised that my daughters would be in to upgrade the lines.
When my daughters arrived, there were 2 people in line ahead of them. As the other customers were taken care of and left, it became closing time. Another representative approached DUSTIN telling him he did not "need to do all that, just hurry and get them out". YES!!! The other rep told him to hurry and get the sale out of the store!!! WHO PAYS YOUR BILLS? WHO PROVIDES YOU WITH THAT PAYCHECK AND COMMISSION MONTHLY?? YES, we the customer do!!!
Next, DUSTIN brought out a selection of cases, car chargers and screen protectors from the back of the store advising my daughter to "pick one", as he presented the selection of cases to her. She advised she did not want or need the cases or other items he was offering. He told her the case and screen protector "comes with it". HE LIED to her!! This is unethical and deceptive!! It was not until she arrived home, after being rushed out of the store, she noticed the additional charged for the case and screen protector - which was supposedly included.
I called VZW *611 immediately. I spoke with a gentleman named CASEY who empathized with me and stated he would forward this information to his manager to have his manager contact me. I have waited for a return call and have not received one. If I do not hear back from VZW today, I am returning 2 lines of service, cancelling all 4 lines and taking my service to a carrier that will do what they promise and not unethically obtain sales from paying customers.
The bonus to this story- my daughter is a minor! Not only did he manipulate and lie, but did so to a child!!! I have been a VZW customer for over a decade. When I cancel my service, everyone will know why. In addition, I talked my LARGE corporation into obtaining corporate accounts with VZW. I can assure you, that will also be revoked.
Best Wishes

Sadly, i've had a few unethical issues of my own and i'm an adult. I do think there was some responsiblity on the daughters' part to verify what they were paying for before leaving the store even though you made an honest attempt to have things laid out prior to their arrival. In regards to VZW's service, It has declined horribly over the past few years. I've been a customer since they were orignally a company called PrimeCo and I'm on the verge of switching providers myself. I had a defective phone that was replaced 6 times in one year..the store manager called me out the blue to apologize for the defective phones and offered me a free upgrade at no charge. He NEVER told me that he was extending my contract and treating it like a normal upgrade. I didn't find out until i went for my New Every Two purchase. I also received a letter stating they were discontinuing the New Every Two Program, but i still would be able to use my last upgrade on my next purchase. Of course when the renewal period came around, there was no such record of the offer and I got nothing. It's now time to renew my contract again and upgrade, but as before, there is absolutely no incentive for me doing so. I'm still going to pay the same as any new customer that walks through the door, still paying an activation fee, and i don't have unlimited everything like most other providers are currently offering. So please tell me again WHY i would want to renew my contract and purchase a new phone from Verizon when i can go elsewhere and get all types of perks???
All in all, i truly sympathize with you and as of today, i'm looking to purchase a new phone this afternoon with another provider.

Service Items for Line Type as Service

I have created a new line type in purchasing as 'Service'. The Value Basis is 'Amount' and Purchasing Basis is 'Services'. Now when I am trying to create a PO for this line type, the Item field is non updateable. I cannot search for any items.
Can I not create and select items for this line type?

Hi,
This seems to be the current functionality. Instead of choosing the item, you can fill the category and description.
If you are trying to treat your purchasable services as item, than try using line type with similar setting as Goods
Thanks

Service Contract Usage line Invoice Amount

Hello All,
I have created Service contract with a Usagline and Service line. When entered the Counter reading, and run the 'Service Contract Main billing program', i am getting the invoice amont of 0 only. Could you please tell me how can i proceed.
And also, what is the relation between 'Service Contract Main Billing Program' and 'QP_CUSTOM' (I have to bill the usage line based on my own logic)
Please help me
Thanks inadvance,
Amarnadh

Did not understand your question, at least completely. The steps you described and the functionality provided is all right.
Is the question, which one of these two values to choose from or why they are two values in the LOV?
Thanks
Nagamohan

How to execute IDC services from command line

Hey Guys,
is there some way we can execute IDC Services from command prompt.
your any pointers will be highly appriciated.
regards,
sapan
Edited by: sapan on Mar 9, 2009 7:26 AM

Hey sapan,
You can use IdcCommand to execute services from the command line. The process is as follows:
1. Create a text file with the services calls you want to make, the definitions are in hda format:
@Properties LocalData
IdcService=UPDATE_DOCINFO
dID=1
dDocName=000001
dDocType=MyType
dSecurityGroup=Public
dRevLabel=1
dDocAuthor=sysadmin
dDocTitle=My Title
@end
<<EOD>>
(Note: for multiple entries in the file <<EOD>> is very important)
2. Execute IdcCommand from the <content server install>/bin directory:
IdcCommand -f image_update.hda -u sysadmin -l c:\idccommand.log
Options:
-f = file with service definitions
-u = user to run as
-l (lowercase L) = location for log of execution
More detailed documentation can be found in the Idc Command Reference (idc_command_reference_10en.pdf).
Hope that helps,
Andy Weaver - Software Consultant
Fishbowl Solutions < http://www.fishbowlsolutions.com?WT.mc_id=L_Oracle_Consulting_amw >

How to start OracleOraDb10g_home1iSQL*Plus service from command line (PC)

After installing 10G, I now have a service with this name: OracleOraDb10g_home1iSQL*Plus
I need to be able to start/stop the service from windows 2000 command line,
BUT "net start OracleOraDb10g_home1iSQL*Plus" DOES NOT WORK.
Adding quotes around the service name does not solve the problem either.
Both attempts give "The service name is invalid" errors.
Can anyone provide a solution?
THANKS!

Sorry, but none of the suggestions works. Thanks for trying though.
1) Renaming the service only changes the display name, and then when you use "net start", it errors with: "The service name is invalid"
2) call isqlplus start errors with "isqlplus is not recognized as an internal or external command..."
3) You cannot execute isqlplussvc.exe directly either.
Any more suggestions?

How to programatically start j2ee application/service from command line

Hi all
We have developed a j2ee application and deployed the .ear file on SAP J2EE (Netweaver'04) engine.
We are able to successfully start/stop the application from Visual administrator -> Deploy -> Service -> Start application (or) Stop application.
We need to start and stop the same application programatically or via command line instead of doing it from VA. Any thoughts from anyone on how to do it ?
Thanks in advance.
Regards
Nagesh

The cammands are there in the respective folders, these are just the batch files / .sh scripts that can be run from command line.
/usr/sap/<instance>JC<client>/j2ee/admin
go.sh and go.bat can run either on command line
j2ee/configtool
configtool.sh / configtool.bat
similarly for other smaller utilities. For the main server, the related commands are in exe directory of sapmnt
/sapmnt/<instance>/exe
Regards,
Nitin
Edited by: Nitin Mahajan on Jun 16, 2009 11:16 PM

QoS for FXS analogue lines

Hi
I have a situation where I will be installing 2 analogue phones via FXS ports.
Is there any way to tag these ports/DNs in order for me to capture any calls to and from so I can create a policy-map for them.
On the same router we have approx 10 IP phones on LAN, this is a remote site and often falls over to low B/W sat link and I want to reserve B/W for these analouge lines in QoS.
Any advice appreciated.

On the dial-peer, you can specify a DSCP value with 'ip qos dscp.' You can use that to map the special phones to a specific value and then use the downstream policy map to differentiate what WAN egress queues the different DSCPs should go.
I would do that on the outbound dial-peer. You can't do it on a per-phone or per-DN basis on CME, so it needs to be done on the H.323/SIP VoIP peer pointing to the other side. Probably what I would do is leave the special phones with media of EF, and I'd mark all of the non-special phones to do DSCP of AF41 and if the WAN doesn't hae provisioning for an AF41 queue, strip the DSCP of AF41 to 0 at the WAN egress.

Star Services on Analogue line

Similar Messages

Maybe you are looking for