Station is not receiving an IP address from DHCP

Hello guys,
I have an ASA 5505 functioning as a router to connect to the Internet. Also, it is my DHCP server for my clients, and APs. When I connect my laptop to the ASA, I get an IP address and able to configure my WLC. The APs also receives an IP address from the ASA. However, when I connect to the AP wirelessly as a wireless client, my laptop is not receiving an IP address from the DHCP which is my ASA.
Here is my topology:
[3602i]--------[ASA5505]--------[WLC2504]
Here is my ASA config for my clients:
interface Vlan12
description *** DEFAULT GATEWAY FOR Wi-Fi GUESTS
nameif GUESTS-if
security-level 100
ip address 10.2.12.1 255.255.255.0
dhcpd address 10.2.12.100-10.2.12.131 GUESTS-if
dhcpd dns 208.67.222.222 208.67.220.220 interface GUESTS-if
dhcpd lease 1048575 interface GUESTS-if
dhcpd option 3 ip 10.2.12.1 interface GUESTS-if
dhcpd enable GUESTS-if
Here is the WLC interface config:

Hello jsnyder81,
I have another question. This is still related to the same network.
I am able to connect to the wireless network now, and receiving IP address from the ASA 5505; however, I can only ping my wireless gateway. I also don't have access to the Internet.
When I hard wired my laptop to the ASA's switch port, I am able to browse the Internet, but not via WiFi.
Here is the routing table that I have on the ASA:
Gateway of last resort is 192.168.1.1 to network 0.0.0.0
C    10.2.8.0 255.255.255.0 is directly connected, PRINTERS-if
C    10.2.9.0 255.255.255.0 is directly connected, FIOS-if
C    10.2.10.0 255.255.255.0 is directly connected, IP-CAMERAS-if
C    10.2.11.0 255.255.255.0 is directly connected, WiFi-USERS-if
C    10.2.12.0 255.255.255.0 is directly connected, GUESTS-if
C    10.2.13.0 255.255.255.0 is directly connected, WIRED-if
C    10.2.3.0 255.255.255.0 is directly connected, EXSi-if
C    10.2.4.0 255.255.255.0 is directly connected, AD/NPS/CA-if
C    10.2.5.0 255.255.255.0 is directly connected, inside
C    10.2.6.0 255.255.255.0 is directly connected, WLC-if
C    10.2.7.0 255.255.255.0 is directly connected, AP-if
C    10.2.20.0 255.255.255.0 is directly connected, WIRELESS-PILOT-if
C    10.2.21.0 255.255.255.0 is directly connected, WIRED-PILOT-if
C    10.2.22.0 255.255.255.0 is directly connected, SERVERS-PILOT-if
C    192.168.1.0 255.255.255.0 is directly connected, outside
d*   0.0.0.0 0.0.0.0 [1/0] via 192.168.1.1, outside
I also have this command:
same-security-traffic permit inter-interface

Similar Messages

Not receiving temp IPv6 address from router

I have spent the day trying to get IPv6 internet connectivity working in Arch and Im failing. No matter what I do my Arch install just isnt receiving and ipv6 temp address. If I use the exact same system but boot into another OS i automatically get an IPv6 temp address and can ping 1pv6.google.com .
If there is anything that might prevent this networking function from working Id appreciate to know what it could be. Thanks a lot.

I wont consider this solved until auto config works but in the mean time I have an ugly work around. I created a profile for eth0 to come up at 0.0.0.0 and I got static ipv6 working in my bridge like this
INTERFACE="br0"
CONNECTION="bridge"
DESCRIPTION="Gigabit Bridge"
POST_UP="ip -6 route add default via fe80::c851:85ff:fed0:e71f dev br0"
BRIDGE_INTERFACES="eth0"
IP="dhcp"
IP6="static"
ADDR6=(2001:470:1f07:be8:bd9a:b66d:248a:b866/64)
Gateway6=fe80::c851:85ff:fed0:e71f
ADDR='192.168.11.66'
#ROUTES=('192.168.0.0/24 via 192.168.1.2')
#GATEWAY='192.168.11.1'
#DNS=('8.8.8.8')

Mail 4.5 does not receive 2 email addresses from friends

Why cann't I receive 2 of my friends email but I can receive on my other Mac Mail account? I have OSX 10.6.8 & Mail 4.5!

Have you tried rebuilding the mailbox?
select the mailbox you want to rebuild (your inbox or custom malbox you created)
click on mailbox in the menubar
select rebuild
If you have a lot of email in the mailbox it might take a little time to finish
I did this when I was no able to see all of my emails and it worked like a charm!

Airport extreme not receiving an ip address

Hey i was wondering if anyone knew why my airport extreme is not receiving an ip address. Im connected to the internet through a cable modem connected to a airport extreme. I know the internet works because when i connect directly to my macpro book the internet works fine.......its just when i try to use my wireless network. Also its not my wireless card in my laptop because it works fine with other wireless networks. The other thing is i know my airport extreme works because it will connect for a while and then it wont connect at all until i reset everything (modem, computer, airport).....any suggestions?
I called apple support and they said it was a comcast problem and comcast said it was a problem with my airport extreme......figures huh?
macpro book 15" Mac OS X (10.4.8)
macpro book 15" Mac OS X (10.4.8)

i think i found the answer while browsing the archives.
http://discussions.apple.com/thread.jspa?messageID=2202720&#2202720
sjones posted this:
FIXED!
Ok, after getting the usual run around with apple not being able to advise me about my ISP and my ISP not being able to advise me about apple some wonderful support person at my ISP let a bit of info slip: Comcast have decomissioned a load of bad DNS servers today.
If you use Comcast and cannot connect via wireless try this:
Open applications/utilities/airport admin utility
select your base station
click configure
click internet
whatever is typed into the dns servers input boxes, delete it
update your base station
and you are connected to the internet.
It makes perfect sense if you have this problem. You base station has been trying to connect to the WAN using a decomissioned dns server. All Comcast dns servers are now distributed dynamically via the dhcp server.
I am working again! Hope you are too.
I tried it, and was able to connect to my mini-mac for the first time. Phew! Now, I'm going to try the printer and my powerbook. I hope my tinkering with those does not tamper with the delicate balance of the universe.
Sjones, if you see this, THANK YOU!
Power PC G4 & Mac Mini Mac OS X (10.4.3)

I am trying to create my Apple ID, but not receiving the verification link from Apple,. I get the email but NOT the link,. any suggestions

I am trying to create my Apple ID, but not receiving the verification link from Apple,. I get the email but NOT the link,. I have triple checked my email address and all Apple account info, all of which are correct. Any suggestions?

Where are you trying to create it?
Go to appleid.apple.com and create it there. Type the country name in the space and a dropdown should appear. Nigeria is clearly available there.

TS4002 Not receiving emails w/ attachments from a few of my existing contacts

This is a problem I just started having in the last couple weeks! I am not receiving emails w/ attachments from two of my every day mail contacts. Both of these people are with different organizations with different email accounts. If they send me an email without an attachment I receive it, but when they send one with an attachment, I don't even get a notification that they TRIED to send it! I have missed multiple emails from important business clients and my realtor! I have received hundreds of emails from these clients over the last 3 years. The attachments are simple PDF files so I know they are not exceeding the limit. They do not show up on the iCloud site, in my Mail app, or on my iPhone.
I have had several other contacts send me attachments which I receive as expected.
I have an @me.com account. Have had no complaints until now.
Any help?

Hi Tattoosleeve,
I suggest double check the Anti-Spam configuration if you have enabled it. More details in the following link:
http://technet.microsoft.com/en-us/library/aa997242.aspx
Did the customers get NDRs when they can't send to your org? If yes, please paste the details without sensitive information for the further troubleshooting.
I want to double confirm your Exchange server version. If you are using Exchange Online, I suggest contact Exchange Online Forum for help so that we can get more professional suggestion. For your convenience:
http://social.technet.microsoft.com/Forums/msonline/en-US/home?forum=onlineservicesexchange
Thanks
Mavis
Mavis Huang
TechNet Community Support

When I try to use the Vision Acquisition vi, I get an error message saying that " The system did not receive a test packet from the camera."

Error -1074360271 occurred at IMAQdx Start Acquisition.vi
NI-IMAQdx: (Hex 0xBFF69031) The system did not receive a test packet from the camera. The packet size may be too large for the network configuration or a firewall may be enabled.

Bruce Ammons wrote:
Did you try disabling test packets? I know Basler cameras have a "Enable Test Packets" setting buried in Advanced Network settings or something like that. You have to change the setting in MAX to show all settings instead of just acquisition, then locate the setting. I have been told regularly that the setting must be turned off for Basler cameras to work properly. Perhaps your camera has the same setting and the same requirement.
Bruce
A very specific firmware revision for certain Basler cameras had an issue where the test packet would not be sent for certain packet sizes and certain specific conditions, causing a false report of a test packet failure when a normal acquisition would in fact succeed. However, this was fixed in later firmware revisions and I have never seen a similar issue on any other types of cameras.
Aside from this specific case, if a test packet fails, it generally means an acquisition will as well. Given that Pleora's software can acquire, we can rule out networking topology and hardware, assuming you are using the same packet size as the Pleora software is. The only other thing that would seem a likely candidate would be a software issue like a firewall or some other filter driver that is interefering with IMAQdx receiving the data.
Eric

Rates being redetermined. Form not received for delivery 0040008146 from 00

Hi ! All,
I m creating a Export Proforma Invoice ( It is a copy of Billing Type JEX ) with respect to a delivery , I am getting the following error-
Rates being redetermined. Form not received for delivery 0040008146 from 0000000012
Message no. 8I642
Diagnosis
Excise rates are being re-determined. This is becuase you have not received the Concession form for the delivery document & yet from the customer &
System Response
System will apply the normal excise duty rates and generate an excise invoice
Procedure
In case you have forgotten to record the receipt of the Forms please do so in Forms tracking for the Sales order and delivery.
Please analyse and let me know what is possible solution.
Regards,
Ashutosh

I feel the process what you had narrated itself is wrong.
It seems some zee table is developed wherein, the users should maintain data related to some concession forms which I feel should be applicable to domestic sales.
Apart from the above, for exports, I dont know why you were generating proforma copying billing type JEX. You were supposed to copy F5 (order related proforma) or F8 (delivery related proforma).
Since in your case, you have indicated that you have generated against a delivery, you should copy F8 billing type and maintain copy control accordingly in VTFL.
Last but not least, the message number also seems to be not a standard one.
thanks
G. Lakshmipathi

I have forgot my I pad In saudi airlines SV883 , on 09-09-2012, then I have immediate inform them but not received any feed back from their side, please advise and protect my Ipad.

Dear Sir,
I have forgot my I pad In saudi airlines SV883 , on 09-09-2012, then I have immediate informed them but not received any feed back from their side, please advise and protect my Ipad.
LOCATION : SAUDI ARABIA. DAMMAM - I have travelled from KOZHIKODE TO DAMMAM.
I HAVE KEPT MY IPAD SEAT POCKET#42H, ,
I have tay it several time thru ICloud still it's in offline.
Saudi air lines customer support services not responding properly,
You are requested to protect my IPAD and advice for the next.
* Can I get back up files from that IPad.,
waiting for your prompt reply as soon as possible,
best regards,
ZAMEER MAIDANI
<Personal Information Edited By Host>

This is a user-to-user technical support forum. We can't do anything to "protect" your iPad. If your files are backed up (and only you would know if so and where) you should be able to access them from your back up.
Did you have Find My iPad enabled?

I can not receive files via bluetooth from other external devices

I can not receive files via bluetooth from other external devices nokia, samsung and other than apple. I can send files to them but not receive. What is the problem?

I sucessfully transfered files from my Nexus4 to MBP via Bluetooth
1. Go to system preference and select Sharing.
2. Check the Bluetooth sharing.
3. Specify directory to which you want to recieve files from Blue tooth device.
4. Turn Blue tooth off and make it on.
Your MBP is now ready to recieve files from Andoriod phone.

I am not receiving security rest question from apple

i am not receiving security rest question from apple, i need to buy some app. please help

Read here > Apple ID: All about Apple ID security questions
If necessary
1) See Here > Apple ID: Contacting Apple for help with Apple ID account security
Ask to speak with the Account Security Team...
2) Or Email Here > Apple Support iTunes Store Contact
Note:
You can only set up a Rescue Email BEFORE you forget the questions/answers.

AP gets always a new IP address from DHCP server

Hello,
When an access points doesn't find a controller it gets always a new IP address from DHCP server.
Does anyone know, why?
thanks

Hi,
From what I know this is to do with DHCP option 60 and 43.Normally when APs request for IP address, DHCP Server also returns the management IP Address of WLC if the VCI matches.
If the VCI sent by the AP does not match with the one configured under DHCP for that particulart AP type, the DHCP will never return the WLC IP and hence AP can not find the controller.And the AP keeps sending DHCP Req and sometimes end up getting two IP addresses!
So may be you can check VCI on DHCP server for that AP model.
Let me know.
Cheers

Clients not receiving addresses from DHCP

I have a Cisco 2811 router and have configured it to be a DHCP server at a remote site. It seems like it should be pretty straight forward to configure DHCP. Apparently I'm missing something because I can't get clients to receive an address. Below are the applicable parts of the config. I also have tried associating the DHCP pool with the Claims vrf and that did not work either.
ip dhcp excluded-address 10.10.30.0 10.10.30.99
ip dhcp excluded-address 10.10.30.201 10.10.30.255
ip dhcp pool Claims_Office
   network 10.10.30.0 255.255.255.0
   domain-name fmi.com
   default-router 10.10.30.253
   dns-server 10.10.10.191
   lease 7
interface FastEthernet0/0
description Claims Office
vrf forwarding Claims
ip address 10.10.30.253 255.255.255.0
duplex auto
speed auto
no mop enabled
interface FastEthernet0/0/0.1205
description Claims Office
vrf forwarding Claims
encapsulation dot1Q 1205
ip address 192.168.103.2 255.255.255.252

Unfortunately that didn't work. Here is the output before:
Pool Claims_Office :
Utilization mark (high/low)    : 100 / 0
Subnet size (first/next)       : 0 / 0
Total addresses                : 254
Leased addresses               : 0
Pending event                  : none
1 subnet is currently in the pool :
Current index        IP address range                    Leased addresses
10.10.30.1           10.10.30.1       - 10.10.30.254      0
And after:
Pool Claims_Office :
Utilization mark (high/low)    : 100 / 0
Subnet size (first/next)       : 0 / 0
Total addresses                : 254
Leased addresses               : 0
Pending event                  : none
1 subnet is currently in the pool :
Current index        IP address range                    Leased addresses
10.10.30.1           10.10.30.1       - 10.10.30.254      0
What I want is for it to assign addresses from 10.10.30.100-199

APs unable to receive IP address from DHCP (core 6500 series switch)

Dear Friends,
a week ago I had stable wireless network APs were getting IPS from 6500 series switch (DHCP) but unfortunately some WISM got rebooted and now APs are unable to receive IP address from Core 6500 DHCP, to cater this issue I have another DHCP server configured on windows 2008 i created another subnet and and put APs in that vlan now all APs are are successfully receiving IPS from windows DHCP server I don't know why APs are not able to receive IPs from core 6500 series DHCP.
please advice
Thanks
Faysal

Thanks george for stepping up here is DHCP config
ip dhcp excluded-address 10.10.30.1 10.10.30.20
ip dhcp excluded-address 10.10.8.1 10.10.8.10
ip dhcp excluded-address 192.168.10.1 192.168.10.5
ip dhcp excluded-address 10.9.20.1 10.9.20.30
ip dhcp pool vlan_30
network 10.10.30.0 255.255.254.0
default-router 10.10.30.1
option 60 ascii """"""""""""""""""""""""CiscoAPc1250""""""""""""""""""""""""
option 43 hex f110.0a0a.1e0b.0a0a.1e0d.0a0a.1e0f.0a0a.1e11
dns-server 10.10.2.11
lease infinite
ip dhcp pool WiSM1_SP
network 192.168.10.0 255.255.255.248
default-router 192.168.10.1

RV042 doesn't receive an IP-address from my ISP on the WAN port

I have a problem with my WAN ports. I can´t obtain a ip adress from my ISP.
I´ve tried factory reset.
Upgrade to lateset firmware.
Clone MAC adress from my PC.
Nothing is working.
But when I plug the WAN port into my Old router it receives an adress directly.
When I plug the ISP connection directly into my pc or the old router it´s working as well.
I using the latest firmware:
RV0XX-v4.1.0.02-tm.bin
And My ISP has an interface with an ADSL modem SmartAX with DHCP.

Hello Ola,
You will most likely need to clone the MAC address of your PC to get this to work. The Modem is not releasing the IP address to the new Router.
Procedures for Cloning a MAC address.
•1.       Disconnect router from Modem.
•2.       Connect Computer to Modem and go to Internet.
•3.       Connect same computer to Router. (Do Not connect router to Modem, and Do not reboot modem.)
•4.       Log into the Router and clone the MAC from the Computer used in the previous step.
•5.       Plug the Router into the Modem.
If that doesnt work check to see if the modem has a selector for MDI/MDIX and switch the selector.
Hope this helps,
Cisco Small Business Support Center
Randy Manthey
CCNA, CCNA - Security

Station is not receiving an IP address from DHCP

Similar Messages

Maybe you are looking for