Still cannot resolve "gethostbyaddr() and reverse DNS name" warnings.

"Mar 15 11:02:48 xs1 servermgrd: servermgr_dns: gethostbyaddr() and reverse DNS name do not match (xs1.dept.school.edu != xs1.dept.School.EDU), various services may not function properly - use changeip to repair and/or correct DNS"
I have two xserves, both of which keep generating the same warnings, ad nauseam, in /var/log/system.log and having followed all suggestions and instructions in discussions, technical notes, afp548.com, and from other sysadmin's I still cannot stop them. There do not seem to be any services affected, or at least not in an overt manner.
Both xserves run slightly different services: (xs1) AFP, Firewall, NetBoot, NFS, Open Directory (slave), Print and Web; and (xs2) AFP, Firewall, Open Directory (master) and Software Update.
On both xserves I have run the following commands/tests with correct results, yet still I get the warnings in system.log: "changeip -checkhostname" is correct, and "scutil --get HostName" is correct. The /etc/hostconfig file is correct with "HOSTNAME=-AUTOMATIC-".
The only thing I can consider is that when setting them up, I had entered the FQDN in all lower-case, but the reverse dns is not, our domain is capitalized, and the tld is in all caps on the DNS servers. I had ages ago issued the "changeip" command as recommended in the warning, to no effect, even though "changeip -checkhostname" says it's correct.
Where the heck to I look now? This is driving me nuts!
RackMac1,1 & RackMac3,1 Mac OS X (10.4.8)

>As of 10.4.6, Apple states to never change /etc/hostconfig's HOSTNAME entry.
Inside the little black box that Apple runs Mac OS X Server this might be good advice. However, in the real world, real servers are often outside of Apple's box (sometimes far outside) and you have to do certain things that Apple don't advise or 'support'.
I can't tell you how many things I run on my servers that are outside the box and judging by other posts on these boards I'm not the only one. You only have to look at DNS, web and mail for starters to see that Apple's model doesn't cover everyone's needs.

Similar Messages

Gethostbyaddr() and reverse DNS name do not match

So we updated to 10.4.6 on our server... and now none of the clients can connect...
Our DNS and reverse DNS (done by the university IT group) have caps in them... but all the home directories for users are lower case...
How can I fix this - short of entering all home directory info in by hand? Oh - suggesting that the IT group change the DNS is not helpful as it will not happen.
Mac OS X (10.4.6) Server

A summary - Here's the situation:
1. I have a 10.4 server running on a G5 tower.
2. The DNS is operated by the university IT group and our reverse DNS is mixed case... asked and they're not going to change it.
3. 10.4.6 introduced some funky stuff with FQDN, DNS and case sensitivity issues.
So... before I changed anything after the 10.4.6 update... users couldn't log in because it couldn't get their home directories...
The automounter would be looking for:
/Network/Servers/servername.Psychology.McMaster.CA/Users/username
While if you looked in /Network/Servers/ you will see:
/Network/Servers/servername.psychology.mcmaster.ca
(note the case)
Alright - moving on:
4. Tried changing hostconfig HOSTNAME - only worked on local server (and you're not supposed to do this anymore).
5. Used changeip same IP address, lower-case name to mixed case name... now users could log in.... glory!
6. Argh... they can log in, but can only intermittently actually get their home directories... seriously. You log in, see your desktop and flash it's gone... clicking on your home directory or desktop in finder gets you 'The volume for "Desktop" cannot be found'... doing "cd ~" and then "ls" from a terminal window sometimes gets you your directory, a partial directory or an error... and even then the ownership maybe the user or root...
7. Looking in the logs we see:
May 25 14:48:26 client kernel[0]: AFP_VFS afpfs_unmount: /private/Network/Servers/servername.psychology.mcmaster.ca/Users, flags 524288, pid 490
May 25 14:48:26 client kernel[0]: AFP_VFS afpfs_MountAFPVolume: GetVolParms failed 0x16
May 25 14:48:26 client automount[490]: Can't mount servername.Psychology.McMaster.CA:/Users on /private/Network/Servers/servername.Psychology.McMaster.CA/Users: Invalid argument (22)
May 25 14:48:26 client automount[490]: Attempt to mount /automount/Servers/servername.Psychology.McMaster.CA/Users returned 22 (Invalid argument)
May 25 14:48:26 client automount[489]: Can't mount servername.Psychology.McMaster.CA:/Users on /private/Network/Servers/servername.Psychology.McMaster.CA/Users: Invalid argument (22)
(server and client names changed to protect the guilty).
I'm stumped... and it's to the point that the owner of said server (a staunch apple supporter) is asking if I can replace the server with a Linux box with LDAP/AFP/SMB...
Any help here?

OS X 10.4.11 Server - configured name and reverse DNS do not match / DNS

Hi all,
I have looked for similar posts but all seem to have different scenarios, hoping to get an answer from someone more experienced than myself before I do anything silly.
Help much appreciated!
Scenario:
We run a 10.4.11 OS X Server on an XServe, hosted at an ISP. ISP provides all DNS services, incl. the reversed DNS entry.
I am currently only running the following services (based on the display in ServerAdmin):
AFP
Firewall
iChat
Mail
QuickTimeStreaming
Web
All others (incl. DNS) are grayed out. (As ISP instructed us not to add a DNS service on our box, that's "normal" according to my experiences with dedicated /co-location server hosting).
We never used changeip after the initial setup, meaning the server's
Current Hostname = somename.local and
DNS Hostname = mail.ourdomainname.net
So in system.log I find this re-occuring entry:
Jul 8 11:41:22 somename servermgrd: servermgr_dns: configured name and reverse DNS name do not match (somename.local != mail.ourdomainname.net), various services may not function properly - use changeip to repair and/or correct DNS
Finally, my question:
As Mail and Web services etc. are currently running OK from what I can tell,
1) do I HAVE to change this at all?
2) Would it be much better / why?
3) Could I change this using the following command
(111.11.111.1 indicating the server's IP address)
changeip 111.11.111.1 111.11.111.1 somename.local mail.ourdomainname.net
4) without running a DNS server on the machine, i.e. DNS service is not required for this to work?
5) obviously I want to be able to use Server Admin after I issue this command...
6) can I fall back easily in case this would screw it up, or is there no risk whatsoever doing this in my case?
THANK YOU so much for any help!

Hi Jonas
If port 443 is already being used on the same box as KMS then it will complain and probably not start the service? I've seen this with LDAP port 636. This is when Kerio is installed on a server configured as an OD Master. Clearly the port can't be used by both servers.
It might be easier to change the port your sites are currently using to something else? Although don't do anything yet. Pose the question to Kerio Support and see what advice they offer.
Yes moving the mail to a local folder on the mail client will do it.
Is Kerio going on the same box? If its a different box (presumably different IP address?) Then what you can do is to port forward to the new server's IP address instead of disabling it. This way while you are bringing the new server on line users can still send mail right up until the time you give instructions on changing their inbound/outbound mail server details. Of course they won't be able to receive but if you time it right they may not even get an error message? Depends on what their schedules are.
If it was me I would choose IMAP every time. As the mail admin you have full control and a central location for easy backup. KMS has a built in archiving feature that makes this a simple process. This is an easier option than going round individual client machines and making sure mail held locally in POP accounts are backed up. Besides there is always someone who falls through the loop and I'm not taking into account drive failures. It makes good sense anyway as there is talk of legislation being introduced to make this a requirement for businesses who run their own mail servers. This is certainly true for certain parts of the US and what usually happens there is generally taken up in the UK and most parts of Europe.
Kerio's WebMail Client means users don't even have to have their own computer. Just as long as they have access to one that has access to the internet they can send/receive mail. No need for dedicated mail applications such as Apple Mail, Thunderbird, Entourage etc. How mail is uses remains consistent for all users.
Yes. I did this not so long ago with Leopard's built in Mail Server. I sent an e-mail defining a time when no inbound mail would be received. Disabled port forwarding for SMTP port 25 and approx 30 minutes after that another mail stating no outbound mail should be sent. Once everything was swopped over (we were changing from a G4 10.4 server to a G5 10.5 Server) port 25 was enabled, new server brought online and everyone was mailing again with no appreciable downtime.
These boxes were to have the same IP address hence the slightly different approach.
Does this help?
Tony

HELP: scheduled jobs no run---searched a lot but still cannot resolve

As for this problem, I have searched a lot by google, but I still cannot resolve it.
I am using 11g on Linux.
I delete all of jobs in my database.Then I configured a very simple periodic job as follows:
begin
DBMS_SCHEDULER.create_job (job_name => 'test2',
program_name => 'test_program',
repeat_interval => 'freq=secondly; INTERVAL= 4',
auto_drop => FALSE);
dbms_scheduler.set_attribute(name => 'test2',
attribute => 'max_runs',
VALUE => 100);
dbms_scheduler.enable('test2');
end;
The program which the job is associated with is as follows:
create or replace PROCEDURE TEST AS
BEGIN
INSERT INTO print_tab VALUES('come on');
commit;
END TEST;
However the table is always empty and the job never runs, and the state shows "SCHEDULED".
The facts are as follows:
1. My database worked very fine until yesterday. This problem occurs suddenly.
2. I also tried to reboot the system, but it did not work.
3. I can manually run the job by DBMS_SCHEDULER.RUN_JOB('test2', TRUE);
4 The process of CJQ, J0 are both running;
5. the value of "job_queue_processess" is 10000, and also i changed it to other values, it did not work;
6. the value of "MAX_JOB_SLAVE_PROCESSES" is 999.
I really do not understand the reason. Who could you give me some guidance. If you need more diagnostic, please tell me how to get them. Great thanks.
Message was edited by:
KingMing

There are many logs in      /u01/app/oracle/diag/rdbms/orcl/orcl/alert, which I checked from the manager console. Could you please help me take a look? Thanks
r 22, 2008 8:16:47 PM EDT     UNKNOWN     16
     Thread 1 advanced to log sequence 3114
Apr 22, 2008 8:16:47 PM EDT     UNKNOWN     16
     Current log# 3 seq# 3114 mem# 0: /u01/app/oracle/oradata/orcl/redo03.log
Apr 22, 2008 8:16:46 PM EDT     UNKNOWN     16
     Thread 1 cannot allocate new log, sequence 3114
Apr 22, 2008 8:16:46 PM EDT     UNKNOWN     16
     Private strand flush not complete
Apr 22, 2008 8:16:46 PM EDT     UNKNOWN     16
     Current log# 2 seq# 3113 mem# 0: /u01/app/oracle/oradata/orcl/redo02.log
Apr 22, 2008 8:00:46 PM EDT     UNKNOWN     16
     Thread 1 advanced to log sequence 3113
Apr 22, 2008 8:00:46 PM EDT     UNKNOWN     16
     Current log# 2 seq# 3113 mem# 0: /u01/app/oracle/oradata/orcl/redo02.log
Apr 22, 2008 1:25:35 PM EDT     UNKNOWN     16
     Thread 1 advanced to log sequence 3112
Apr 22, 2008 1:25:35 PM EDT     UNKNOWN     16
     Current log# 1 seq# 3112 mem# 0: /u01/app/oracle/oradata/orcl/redo01.log
Apr 22, 2008 4:39:32 AM EDT     UNKNOWN     16
     Thread 1 advanced to log sequence 3111
Apr 22, 2008 4:39:32 AM EDT     UNKNOWN     16
     Current log# 3 seq# 3111 mem# 0: /u01/app/oracle/oradata/orcl/redo03.log
Apr 21, 2008 9:15:42 PM EDT     UNKNOWN     16
     Thread 1 advanced to log sequence 3110
Apr 21, 2008 9:15:42 PM EDT     UNKNOWN     16
     Current log# 2 seq# 3110 mem# 0: /u01/app/oracle/oradata/orcl/redo02.log
Apr 21, 2008 8:15:54 PM EDT     UNKNOWN     16
     Thread 1 advanced to log sequence 3109
Apr 21, 2008 8:15:54 PM EDT     UNKNOWN     16
     Current log# 1 seq# 3109 mem# 0: /u01/app/oracle/oradata/orcl/redo01.log
Apr 21, 2008 8:15:54 PM EDT     UNKNOWN     16
     Thread 1 cannot allocate new log, sequence 3109
Apr 21, 2008 8:15:54 PM EDT     UNKNOWN     16
     Private strand flush not complete
Apr 21, 2008 8:15:54 PM EDT     UNKNOWN     16
     Current log# 3 seq# 3108 mem# 0: /u01/app/oracle/oradata/orcl/redo03.log
Apr 21, 2008 3:19:00 PM EDT     NOTIFICATION     16
     process start     ksbrdp:3527:3697353022     CJQ0 started with pid=39, OS id=8880
Apr 21, 2008 3:19:00 PM EDT     NOTIFICATION     16
     process start     ksbs1p_real:2133:2371767696     Starting background process CJQ0
Apr 21, 2008 3:15:48 PM EDT     NOTIFICATION     16
     admin_ddl     opiexe:2995:2802784106     Completed: ALTER DATABASE OPEN
Apr 21, 2008 3:15:46 PM EDT     UNKNOWN     16
     db_recovery_file_dest_size of 2048 MB is 0.00% used. This is a
Apr 21, 2008 3:15:46 PM EDT     UNKNOWN     16
     user-specified limit on the amount of space that will be used by this
Apr 21, 2008 3:15:46 PM EDT     UNKNOWN     16
     database for recovery-related files, and does not reflect the amount of
Apr 21, 2008 3:15:46 PM EDT     UNKNOWN     16
     space available in the underlying filesystem or ASM diskgroup.

How to stop OS X from retrieving reverse DNS name ?!

Hello guys,
I have a small problem that's very annoying. I manage a couple dozen Macs at work via ARD. All Macs are up to date and so is ARD.
Recently i started to notice something bizzare in ARD, meaning that from time to time a couple of Macs that were passed over from an ex employee to another current employee, behaved erradic in ARD. Sometimes they appear offline, sometimes they dissaper entirely (also in Scanner), BUT most of the times they appear with incorrect DNS name (ex DNS name from the ex employee or even duplicates DNS names)
I attached a pic in which you can clearly see what i'm all about.
I tried different situations and config mods, and i almost nailed it when i changed the DHCP DNS settings from the router. Currently the router LAN DNS settings points to the local server (ie: 10.0.1.2) which has DNS enabled and then to the public DNS. If i switch the entires, then the DNS names appear correctly in ARD, but if i do that i also loose the iChat service which is dependent of that entry.
SO i think the best way is to figure out a way to stop OS X from retrieveing reverse DNS names. Is this possible?

I've have this issue too. This thread may be helpful:
https://discussions.apple.com/thread/4190442
Most of our computers have static IP addresses assigned, so it is just some laptops that receive DHCP that seem to get confused in ARD sometimes. As in your case, the computers themselves never have an issue - it is just ARD that gets mixed messages. It also never seems to affect ARD, it just displays incorrectly. While I'm not entirely convinced this is fixable, I took the advice of the thread above and when it gets really bad, I simply go to "All Computers" and delete everything out. Then I quit and reopen ARD and then from the Scanner, I re-add the computers and re-organize them. We only have about 30 computers, so it goes quick when they are all turned on. They seem to stay pretty organized for a while... and then the cycle begins again.

Error cannot connect to server or DNS name when working with the SRDemo

I receive the error cannot connect to server or Dns name when trying to
display the SRlist.jspx page in the SRDemo. I am using the embedded OC4J server . I tried to using the debugger to trouble shoot the problem but I did not get any information that was useful. The url I am using is http://localhost:8989/SRDemo-UserInterface-context-root/faces/app/SRlist.jspx I also tried using the IP address that didn't work . I really need to get through this demo.

What about using:
http://127.0.0.1:8989/SRDemo-UserInterface-context-root/faces/app/SRlist.jspx
Or disabling any proxy settings your browser might have?

How to find out the primary and failover DNS name

Hi;
This sounds very stupid, but could some one please tell me how to find out the name/dns name of the primary and failover server without using the CDS console.
any help is appreciated

Is this what you want?
$ /usr/lib/ldap/ldap_cachemgr -g
cachemgr configuration:
server debug level 0
server log file "/var/ldap/cachemgr.log"
number of calls to ldapcachemgr 12729
cachemgr cache data statistics:
Configuration refresh information:
Previous refresh time: 2005/08/07 23:54:59
Next refresh time: 2005/08/08 00:55:00
Server information:
Previous refresh time: 2005/08/14 15:15:00
Next refresh time: 2005/08/15 03:15:00
server: ldap1.example.com, status: UP
server: ldap2.example.com, status: UP
server: ldap3.example.com, status: UP
Cache data information:
Maximum cache entries: 256
Number of cache entries: 0
Gary

Exchange 2010 and reverse DNS

Hi
I have two exchange 2010 servers: x.x.x.72 and x.x.x.73
I have a reverse DNS ptr record for both of these machines pointing back to mail.mydomain.com
My users are getting an error message when they try to send mail to a craigslist.com address.
The error I see in the log is:
mail.mydomain.com [x.x.x.73] Please setup matching DNS and rDNS records: http://www.craigslist.org/about/help/rdns_failure
I have an A record [mail.mydomain.com] pointing back to .72
BUT I don't have an A record pointing back to .73.
So, I'm wondering is that what I need to do, create another A record and point .73 back to mail.mydomain.com
I was concerned having two A records pointing back to the same mail.mydomain.com. I wasn't sure if that would cause any problems.
Or should I create a send connector on .72 and only allow mail to be sent out for craigslist.com?
As you can see, I'm unclear on the best way to solve this.
Any advice is welcome.
Thanks!
Mike

Hi ,
If you wanted to use the x.x.x.73 ip address to send emails to internet then you need to have the proper A record and PTR records .
Please have a look in to the below mentioned points .Based upon the provided description i thought you are having like below.
Host A record :
mail.mydomain.com 192.168.1.72
PTR record :
192.168.1.72 mail.mydomain.com
Then on the send connector configuration you need have the smarthost as 192.168.1.72 to send emails to internet otherwise your emails get failed if the remote host has done reverse dns check.check. Because on your side i thought you don't have the proper
A records and PTR records for x.x.x.73
In case if you would like to have two A records .Please have the settings like below :-
Host A record :
mail.mydomain.com 192.168.1.72
mail1.mydomain.com 192.168.1.73
PTR record :
192.168.1.72 mail.mydomain.com
192.168.1.73 mail1.mydomain.com
On the above configuration you can make use of the both the ip's on the smarthost in the send connector to send emails to internet.
Note : You can make use of MXTOOLBOX to check the A and ptr records for your domain.
Please reply me if anything is unclear.
Thanks & Regards S.Nithyanandham

My apple 5th gen ipod is connected to wifi but still cannot access safari and other websites..can some1 help me out?

my apple 5th gen ipod is connected to wifi but still cannot access safari,itunes and other websites. the ip address is not strtng wid 169 and i have reset the network settings also..can some one help me out

The 169 IP address mans it did not correctly negotiate with the router:
Does the iOS device connect to other networks? If yes that tend to indicate a problem with your network.
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

1.9 DVR still cannot resolve recording conflicts?

While I enjoy the improvements in 1.9, the DVR still can't resolve recording conflicts.
My example: 9PM Monday.
1. Last hour of Sing Off
2. Two 1/2 Men
3. Top Gear
4. American Chopper
I have to resolve this manually. One thing I can say for DTV, their DVR's were programmed to know that 3 and 4 would be televised 3 hours later and would schedule the recording. Or know that, as an example, the weeks episode Boardwalk Empire would be televised on HBOW three hours later.

I could not agree more.
The History and Series Priority management need to be better utilized to record missed airings due to conflict.

I had verify my apple ID but I still cannot download anything and it still ask me to verify my ID. I press resend email but no new email coming but when I open my old Email it said I verified already. How to solve this?

Please help me

Had a similar issue a couple of days ago, when my password was not recognized. I KNOW it was correct, yet when I checked in settings, the number of asterisks were far too few for my password. Ended up with my account disabled, so I had to request a reset, the link was sent the back up email account I created when I got my unit.
Today, I was asked to confirm credit card info when trying to download a FREE app. I suppose that is for any future in-app purchases....at least, I hope so!

People still cannot text me and I have removed my device from my account

Need help trying to allow my messages to go to my new phone that is an android... I switched from iPhone to android... Help!!

Contact Apple customer support for further assistance.

Resolve.conf, dnsmasq and external DNS servers

I am using dnsmasq to filter out ad urls, so my /etc/resolv.conf looks like that:
# Generated by dhcpcd from wlan0
nameserver 127.0.0.1
domain home
nameserver 192.168.1.254
# /etc/resolv.conf.tail can replace this line
However, it looks like after getting through the url filtration layer of dnsmasq, the URLs are being resolved by a DNS sever of whatever Access Point I am connected to. This create problems, because they often render me unable to connect to services like sourceforge.net, etc.
So, instead of that, I would like my system to fall back to Google and OpenDNS after filtering urls through dnsmasq.
But how can I do that? This is a specific case and wiki does not cover it.
Last edited by Lockheed (2013-05-19 16:50:43)

$ cat /etc/resolv.conf
# Generated by dhcpcd from wlan0
nameserver 127.0.0.1
nameserver 8.8.8.8
domain home
# /etc/resolv.conf.tail can replace this line
The google DNS is what I put in there earlier to be able to use internet after dnsmasq stopped starting.
$ cat /etc/resolvconf.conf
# Configuration for resolvconf(8)
# See resolvconf.conf(5) for details
resolv_conf=/etc/resolv.conf
# If you run a local name server, you should uncomment the below line and
# configure your subscribers configuration files below.
name_servers=127.0.0.1
# Write out dnsmasq extended configuration and resolv files
dnsmasq_conf=/etc/dnsmasq-conf.conf
dnsmasq_resolv=/etc/dnsmasq-resolv.conf
$ cat /etc/dnsmasq.conf
# Configuration file for dnsmasq.
# Format is one option per line, legal options are the same
# as the long options legal on the command line. See
# "/usr/sbin/dnsmasq --help" or "man 8 dnsmasq" for details.
# Listen on this specific port instead of the standard DNS port
# (53). Setting this to zero completely disables DNS function,
# leaving only DHCP and/or TFTP.
#port=5353
# The following two options make you a better netizen, since they
# tell dnsmasq to filter out queries which the public DNS cannot
# answer, and which load the servers (especially the root servers)
# unnecessarily. If you have a dial-on-demand link they also stop
# these requests from bringing up the link unnecessarily.
# Never forward plain names (without a dot or domain part)
#domain-needed
# Never forward addresses in the non-routed address spaces.
#bogus-priv
# Uncomment this to filter useless windows-originated DNS requests
# which can trigger dial-on-demand links needlessly.
# Note that (amongst other things) this blocks all SRV requests,
# so don't use it if you use eg Kerberos, SIP, XMMP or Google-talk.
# This option only affects forwarding, SRV records originating for
# dnsmasq (via srv-host= lines) are not suppressed by it.
#filterwin2k
# Change this line if you want dns to get its upstream servers from
# somewhere other that /etc/resolv.conf
#resolv-file=/etc/resolv-dnsmasq.conf
# By default, dnsmasq will send queries to any of the upstream
# servers it knows about and tries to favour servers to are known
# to be up. Uncommenting this forces dnsmasq to try each query
# with each server strictly in the order they appear in
# /etc/resolv.conf
strict-order
# If you don't want dnsmasq to read /etc/resolv.conf or any other
# file, getting its servers from this file instead (see below), then
# uncomment this.
#no-resolv
# If you don't want dnsmasq to poll /etc/resolv.conf or other resolv
# files for changes and re-read them then uncomment this.
#no-poll
# Add other name servers here, with domain specs if they are for
# non-public domains.
#server=/localnet/192.168.0.1
server=208.67.222.222
server=208.67.220.220
# Example of routing PTR queries to nameservers: this will send all
# address->name queries for 192.168.3/24 to nameserver 10.1.2.3
#server=/3.168.192.in-addr.arpa/10.1.2.3
# Add local-only domains here, queries in these domains are answered
# from /etc/hosts or DHCP only.
#local=/localnet/
# Add domains which you want to force to an IP address here.
# The example below send any host in double-click.net to a local
# web-server.
#address=/double-click.net/127.0.0.1
# --address (and --server) work with IPv6 addresses too.
#address=/www.thekelleys.org.uk/fe80::20d:60ff:fe36:f83
# You can control how dnsmasq talks to a server: this forces
# queries to 10.1.2.3 to be routed via eth1
# server=10.1.2.3@eth1
# and this sets the source (ie local) address used to talk to
# 10.1.2.3 to 192.168.1.1 port 55 (there must be a interface with that
# IP on the machine, obviously).
# [email protected]#55
# If you want dnsmasq to change uid and gid to something other
# than the default, edit the following lines.
#user=
#group=
# If you want dnsmasq to listen for DHCP and DNS requests only on
# specified interfaces (and the loopback) give the name of the
# interface (eg eth0) here.
# Repeat the line for more than one interface.
#interface=lo
# Or you can specify which interface _not_ to listen on
#except-interface=
# Or which to listen on by address (remember to include 127.0.0.1 if
# you use this.)
#listen-address=127.0.0.1
# If you want dnsmasq to provide only DNS service on an interface,
# configure it as shown above, and then use the following line to
# disable DHCP and TFTP on it.
#no-dhcp-interface=
# On systems which support it, dnsmasq binds the wildcard address,
# even when it is listening on only some interfaces. It then discards
# requests that it shouldn't reply to. This has the advantage of
# working even when interfaces come and go and change address. If you
# want dnsmasq to really bind only the interfaces it is listening on,
# uncomment this option. About the only time you may need this is when
# running another nameserver on the same machine.
#bind-interfaces
# If you don't want dnsmasq to read /etc/hosts, uncomment the
# following line.
#no-hosts
# or if you want it to read another file, as well as /etc/hosts, use
# this.
addn-hosts=/etc/hosts.block
#hostsfile=/etc/hosts.block
# Set this (and domain: see below) if you want to have a domain
# automatically added to simple names in a hosts-file.
#expand-hosts
# Set the domain for dnsmasq. this is optional, but if it is set, it
# does the following things.
# 1) Allows DHCP hosts to have fully qualified domain names, as long
# as the domain part matches this setting.
# 2) Sets the "domain" DHCP option thereby potentially setting the
# domain of all systems configured by DHCP
# 3) Provides the domain part for "expand-hosts"
#domain=thekelleys.org.uk
# Set a different domain for a particular subnet
#domain=wireless.thekelleys.org.uk,192.168.2.0/24
# Same idea, but range rather then subnet
#domain=reserved.thekelleys.org.uk,192.68.3.100,192.168.3.200
# Uncomment this to enable the integrated DHCP server, you need
# to supply the range of addresses available for lease and optionally
# a lease time. If you have more than one network, you will need to
# repeat this for each network on which you want to supply DHCP
# service.
#dhcp-range=192.168.0.50,192.168.0.150,12h
# This is an example of a DHCP range where the netmask is given. This
# is needed for networks we reach the dnsmasq DHCP server via a relay
# agent. If you don't know what a DHCP relay agent is, you probably
# don't need to worry about this.
#dhcp-range=192.168.0.50,192.168.0.150,255.255.255.0,12h
# This is an example of a DHCP range which sets a tag, so that
# some DHCP options may be set only for this network.
#dhcp-range=set:red,192.168.0.50,192.168.0.150
# Use this DHCP range only when the tag "green" is set.
#dhcp-range=tag:green,192.168.0.50,192.168.0.150,12h
# Specify a subnet which can't be used for dynamic address allocation,
# is available for hosts with matching --dhcp-host lines. Note that
# dhcp-host declarations will be ignored unless there is a dhcp-range
# of some type for the subnet in question.
# In this case the netmask is implied (it comes from the network
# configuration on the machine running dnsmasq) it is possible to give
# an explicit netmask instead.
#dhcp-range=192.168.0.0,static
# Enable DHCPv6. Note that the prefix-length does not need to be specified
# and defaults to 64 if missing/
#dhcp-range=1234::2, 1234::500, 64, 12h
# Do Router Advertisements, BUT NOT DHCP for this subnet.
#dhcp-range=1234::, ra-only
# Do Router Advertisements, BUT NOT DHCP for this subnet, also try and
# add names to the DNS for the IPv6 address of SLAAC-configured dual-stack
# hosts. Use the DHCPv4 lease to derive the name, network segment and
# MAC address and assume that the host will also have an
# IPv6 address calculated using the SLAAC alogrithm.
#dhcp-range=1234::, ra-names
# Do Router Advertisements, BUT NOT DHCP for this subnet.
# Set the lifetime to 46 hours. (Note: minimum lifetime is 2 hours.)
#dhcp-range=1234::, ra-only, 48h
# Do DHCP and Router Advertisements for this subnet. Set the A bit in the RA
# so that clients can use SLAAC addresses as well as DHCP ones.
#dhcp-range=1234::2, 1234::500, slaac
# Do Router Advertisements and stateless DHCP for this subnet. Clients will
# not get addresses from DHCP, but they will get other configuration information.
# They will use SLAAC for addresses.
#dhcp-range=1234::, ra-stateless
# Do stateless DHCP, SLAAC, and generate DNS names for SLAAC addresses
# from DHCPv4 leases.
#dhcp-range=1234::, ra-stateless, ra-names
# Do router advertisements for all subnets where we're doing DHCPv6
# Unless overriden by ra-stateless, ra-names, et al, the router
# advertisements will have the M and O bits set, so that the clients
# get addresses and configuration from DHCPv6, and the A bit reset, so the
# clients don't use SLAAC addresses.
#enable-ra
# Supply parameters for specified hosts using DHCP. There are lots
# of valid alternatives, so we will give examples of each. Note that
# IP addresses DO NOT have to be in the range given above, they just
# need to be on the same network. The order of the parameters in these
# do not matter, it's permissible to give name, address and MAC in any
# order.
# Always allocate the host with Ethernet address 11:22:33:44:55:66
# The IP address 192.168.0.60
#dhcp-host=11:22:33:44:55:66,192.168.0.60
# Always set the name of the host with hardware address
# 11:22:33:44:55:66 to be "fred"
#dhcp-host=11:22:33:44:55:66,fred
# Always give the host with Ethernet address 11:22:33:44:55:66
# the name fred and IP address 192.168.0.60 and lease time 45 minutes
#dhcp-host=11:22:33:44:55:66,fred,192.168.0.60,45m
# Give a host with Ethernet address 11:22:33:44:55:66 or
# 12:34:56:78:90:12 the IP address 192.168.0.60. Dnsmasq will assume
# that these two Ethernet interfaces will never be in use at the same
# time, and give the IP address to the second, even if it is already
# in use by the first. Useful for laptops with wired and wireless
# addresses.
#dhcp-host=11:22:33:44:55:66,12:34:56:78:90:12,192.168.0.60
# Give the machine which says its name is "bert" IP address
# 192.168.0.70 and an infinite lease
#dhcp-host=bert,192.168.0.70,infinite
# Always give the host with client identifier 01:02:02:04
# the IP address 192.168.0.60
#dhcp-host=id:01:02:02:04,192.168.0.60
# Always give the host with client identifier "marjorie"
# the IP address 192.168.0.60
#dhcp-host=id:marjorie,192.168.0.60
# Enable the address given for "judge" in /etc/hosts
# to be given to a machine presenting the name "judge" when
# it asks for a DHCP lease.
#dhcp-host=judge
# Never offer DHCP service to a machine whose Ethernet
# address is 11:22:33:44:55:66
#dhcp-host=11:22:33:44:55:66,ignore
# Ignore any client-id presented by the machine with Ethernet
# address 11:22:33:44:55:66. This is useful to prevent a machine
# being treated differently when running under different OS's or
# between PXE boot and OS boot.
#dhcp-host=11:22:33:44:55:66,id:*
# Send extra options which are tagged as "red" to
# the machine with Ethernet address 11:22:33:44:55:66
#dhcp-host=11:22:33:44:55:66,set:red
# Send extra options which are tagged as "red" to
# any machine with Ethernet address starting 11:22:33:
#dhcp-host=11:22:33:*:*:*,set:red
# Give a fixed IPv6 address and name to client with
# DUID 00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2
# Note the MAC addresses CANNOT be used to identify DHCPv6 clients.
# Note also the they [] around the IPv6 address are obilgatory.
#dhcp-host=id:00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2, fred, [1234::5]
# Ignore any clients which are not specified in dhcp-host lines
# or /etc/ethers. Equivalent to ISC "deny unknown-clients".
# This relies on the special "known" tag which is set when
# a host is matched.
#dhcp-ignore=tag:!known
# Send extra options which are tagged as "red" to any machine whose
# DHCP vendorclass string includes the substring "Linux"
#dhcp-vendorclass=set:red,Linux
# Send extra options which are tagged as "red" to any machine one
# of whose DHCP userclass strings includes the substring "accounts"
#dhcp-userclass=set:red,accounts
# Send extra options which are tagged as "red" to any machine whose
# MAC address matches the pattern.
#dhcp-mac=set:red,00:60:8C:*:*:*
# If this line is uncommented, dnsmasq will read /etc/ethers and act
# on the ethernet-address/IP pairs found there just as if they had
# been given as --dhcp-host options. Useful if you keep
# MAC-address/host mappings there for other purposes.
#read-ethers
# Send options to hosts which ask for a DHCP lease.
# See RFC 2132 for details of available options.
# Common options can be given to dnsmasq by name:
# run "dnsmasq --help dhcp" to get a list.
# Note that all the common settings, such as netmask and
# broadcast address, DNS server and default route, are given
# sane defaults by dnsmasq. You very likely will not need
# any dhcp-options. If you use Windows clients and Samba, there
# are some options which are recommended, they are detailed at the
# end of this section.
# Override the default route supplied by dnsmasq, which assumes the
# router is the same machine as the one running dnsmasq.
#dhcp-option=3,1.2.3.4
# Do the same thing, but using the option name
#dhcp-option=option:router,1.2.3.4
# Override the default route supplied by dnsmasq and send no default
# route at all. Note that this only works for the options sent by
# default (1, 3, 6, 12, 28) the same line will send a zero-length option
# for all other option numbers.
#dhcp-option=3
# Set the NTP time server addresses to 192.168.0.4 and 10.10.0.5
#dhcp-option=option:ntp-server,192.168.0.4,10.10.0.5
# Send DHCPv6 option. Note [] around IPv6 addresses.
#dhcp-option=option6:dns-server,[1234::77],[1234::88]
# Send DHCPv6 option for namservers as the machine running
# dnsmasq and another.
#dhcp-option=option6:dns-server,[::],[1234::88]
# Ask client to poll for option changes every six hours. (RFC4242)
#dhcp-option=option6:information-refresh-time,6h
# Set the NTP time server address to be the same machine as
# is running dnsmasq
#dhcp-option=42,0.0.0.0
# Set the NIS domain name to "welly"
#dhcp-option=40,welly
# Set the default time-to-live to 50
#dhcp-option=23,50
# Set the "all subnets are local" flag
#dhcp-option=27,1
# Send the etherboot magic flag and then etherboot options (a string).
#dhcp-option=128,e4:45:74:68:00:00
#dhcp-option=129,NIC=eepro100
# Specify an option which will only be sent to the "red" network
# (see dhcp-range for the declaration of the "red" network)
# Note that the tag: part must precede the option: part.
#dhcp-option = tag:red, option:ntp-server, 192.168.1.1
# The following DHCP options set up dnsmasq in the same way as is specified
# for the ISC dhcpcd in
# http://www.samba.org/samba/ftp/docs/textdocs/DHCP-Server-Configuration.txt
# adapted for a typical dnsmasq installation where the host running
# dnsmasq is also the host running samba.
# you may want to uncomment some or all of them if you use
# Windows clients and Samba.
#dhcp-option=19,0 # option ip-forwarding off
#dhcp-option=44,0.0.0.0 # set netbios-over-TCP/IP nameserver(s) aka WINS server(s)
#dhcp-option=45,0.0.0.0 # netbios datagram distribution server
#dhcp-option=46,8 # netbios node type
# Send an empty WPAD option. This may be REQUIRED to get windows 7 to behave.
#dhcp-option=252,"\n"
# Send RFC-3397 DNS domain search DHCP option. WARNING: Your DHCP client
# probably doesn't support this......
#dhcp-option=option:domain-search,eng.apple.com,marketing.apple.com
# Send RFC-3442 classless static routes (note the netmask encoding)
#dhcp-option=121,192.168.1.0/24,1.2.3.4,10.0.0.0/8,5.6.7.8
# Send vendor-class specific options encapsulated in DHCP option 43.
# The meaning of the options is defined by the vendor-class so
# options are sent only when the client supplied vendor class
# matches the class given here. (A substring match is OK, so "MSFT"
# matches "MSFT" and "MSFT 5.0"). This example sets the
# mtftp address to 0.0.0.0 for PXEClients.
#dhcp-option=vendor:PXEClient,1,0.0.0.0
# Send microsoft-specific option to tell windows to release the DHCP lease
# when it shuts down. Note the "i" flag, to tell dnsmasq to send the
# value as a four-byte integer - that's what microsoft wants. See
# http://technet2.microsoft.com/WindowsServer/en/library/a70f1bb7-d2d4-49f0-96d6-4b7414ecfaae1033.mspx?mfr=true
#dhcp-option=vendor:MSFT,2,1i
# Send the Encapsulated-vendor-class ID needed by some configurations of
# Etherboot to allow is to recognise the DHCP server.
#dhcp-option=vendor:Etherboot,60,"Etherboot"
# Send options to PXELinux. Note that we need to send the options even
# though they don't appear in the parameter request list, so we need
# to use dhcp-option-force here.
# See http://syslinux.zytor.com/pxe.php#special for details.
# Magic number - needed before anything else is recognised
#dhcp-option-force=208,f1:00:74:7e
# Configuration file name
#dhcp-option-force=209,configs/common
# Path prefix
#dhcp-option-force=210,/tftpboot/pxelinux/files/
# Reboot time. (Note 'i' to send 32-bit value)
#dhcp-option-force=211,30i
# Set the boot filename for netboot/PXE. You will only need
# this is you want to boot machines over the network and you will need
# a TFTP server; either dnsmasq's built in TFTP server or an
# external one. (See below for how to enable the TFTP server.)
#dhcp-boot=pxelinux.0
# The same as above, but use custom tftp-server instead machine running dnsmasq
#dhcp-boot=pxelinux,server.name,192.168.1.100
# Boot for Etherboot gPXE. The idea is to send two different
# filenames, the first loads gPXE, and the second tells gPXE what to
# load. The dhcp-match sets the gpxe tag for requests from gPXE.
#dhcp-match=set:gpxe,175 # gPXE sends a 175 option.
#dhcp-boot=tag:!gpxe,undionly.kpxe
#dhcp-boot=mybootimage
# Encapsulated options for Etherboot gPXE. All the options are
# encapsulated within option 175
#dhcp-option=encap:175, 1, 5b # priority code
#dhcp-option=encap:175, 176, 1b # no-proxydhcp
#dhcp-option=encap:175, 177, string # bus-id
#dhcp-option=encap:175, 189, 1b # BIOS drive code
#dhcp-option=encap:175, 190, user # iSCSI username
#dhcp-option=encap:175, 191, pass # iSCSI password
# Test for the architecture of a netboot client. PXE clients are
# supposed to send their architecture as option 93. (See RFC 4578)
#dhcp-match=peecees, option:client-arch, 0 #x86-32
#dhcp-match=itanics, option:client-arch, 2 #IA64
#dhcp-match=hammers, option:client-arch, 6 #x86-64
#dhcp-match=mactels, option:client-arch, 7 #EFI x86-64
# Do real PXE, rather than just booting a single file, this is an
# alternative to dhcp-boot.
#pxe-prompt="What system shall I netboot?"
# or with timeout before first available action is taken:
#pxe-prompt="Press F8 for menu.", 60
# Available boot services. for PXE.
#pxe-service=x86PC, "Boot from local disk"
# Loads <tftp-root>/pxelinux.0 from dnsmasq TFTP server.
#pxe-service=x86PC, "Install Linux", pxelinux
# Loads <tftp-root>/pxelinux.0 from TFTP server at 1.2.3.4.
# Beware this fails on old PXE ROMS.
#pxe-service=x86PC, "Install Linux", pxelinux, 1.2.3.4
# Use bootserver on network, found my multicast or broadcast.
#pxe-service=x86PC, "Install windows from RIS server", 1
# Use bootserver at a known IP address.
#pxe-service=x86PC, "Install windows from RIS server", 1, 1.2.3.4
# If you have multicast-FTP available,
# information for that can be passed in a similar way using options 1
# to 5. See page 19 of
# http://download.intel.com/design/archives/wfm/downloads/pxespec.pdf
# Enable dnsmasq's built-in TFTP server
#enable-tftp
# Set the root directory for files available via FTP.
#tftp-root=/var/ftpd
# Make the TFTP server more secure: with this set, only files owned by
# the user dnsmasq is running as will be send over the net.
#tftp-secure
# This option stops dnsmasq from negotiating a larger blocksize for TFTP
# transfers. It will slow things down, but may rescue some broken TFTP
# clients.
#tftp-no-blocksize
# Set the boot file name only when the "red" tag is set.
#dhcp-boot=net:red,pxelinux.red-net
# An example of dhcp-boot with an external TFTP server: the name and IP
# address of the server are given after the filename.
# Can fail with old PXE ROMS. Overridden by --pxe-service.
#dhcp-boot=/var/ftpd/pxelinux.0,boothost,192.168.0.3
# If there are multiple external tftp servers having a same name
# (using /etc/hosts) then that name can be specified as the
# tftp_servername (the third option to dhcp-boot) and in that
# case dnsmasq resolves this name and returns the resultant IP
# addresses in round robin fasion. This facility can be used to
# load balance the tftp load among a set of servers.
#dhcp-boot=/var/ftpd/pxelinux.0,boothost,tftp_server_name
# Set the limit on DHCP leases, the default is 150
#dhcp-lease-max=150
# The DHCP server needs somewhere on disk to keep its lease database.
# This defaults to a sane location, but if you want to change it, use
# the line below.
#dhcp-leasefile=/var/lib/misc/dnsmasq.leases
# Set the DHCP server to authoritative mode. In this mode it will barge in
# and take over the lease for any client which broadcasts on the network,
# whether it has a record of the lease or not. This avoids long timeouts
# when a machine wakes up on a new network. DO NOT enable this if there's
# the slightest chance that you might end up accidentally configuring a DHCP
# server for your campus/company accidentally. The ISC server uses
# the same option, and this URL provides more information:
# http://www.isc.org/files/auth.html
#dhcp-authoritative
# Run an executable when a DHCP lease is created or destroyed.
# The arguments sent to the script are "add" or "del",
# then the MAC address, the IP address and finally the hostname
# if there is one.
#dhcp-script=/bin/echo
# Set the cachesize here.
#cache-size=150
# If you want to disable negative caching, uncomment this.
#no-negcache
# Normally responses which come from /etc/hosts and the DHCP lease
# file have Time-To-Live set as zero, which conventionally means
# do not cache further. If you are happy to trade lower load on the
# server for potentially stale date, you can set a time-to-live (in
# seconds) here.
#local-ttl=
# If you want dnsmasq to detect attempts by Verisign to send queries
# to unregistered .com and .net hosts to its sitefinder service and
# have dnsmasq instead return the correct NXDOMAIN response, uncomment
# this line. You can add similar lines to do the same for other
# registries which have implemented wildcard A records.
#bogus-nxdomain=64.94.110.11
# If you want to fix up DNS results from upstream servers, use the
# alias option. This only works for IPv4.
# This alias makes a result of 1.2.3.4 appear as 5.6.7.8
#alias=1.2.3.4,5.6.7.8
# and this maps 1.2.3.x to 5.6.7.x
#alias=1.2.3.0,5.6.7.0,255.255.255.0
# and this maps 192.168.0.10->192.168.0.40 to 10.0.0.10->10.0.0.40
#alias=192.168.0.10-192.168.0.40,10.0.0.0,255.255.255.0
# Change these lines if you want dnsmasq to serve MX records.
# Return an MX record named "maildomain.com" with target
# servermachine.com and preference 50
#mx-host=maildomain.com,servermachine.com,50
# Set the default target for MX records created using the localmx option.
#mx-target=servermachine.com
# Return an MX record pointing to the mx-target for all local
# machines.
#localmx
# Return an MX record pointing to itself for all local machines.
#selfmx
# Change the following lines if you want dnsmasq to serve SRV
# records. These are useful if you want to serve ldap requests for
# Active Directory and other windows-originated DNS requests.
# See RFC 2782.
# You may add multiple srv-host lines.
# The fields are <name>,<target>,<port>,<priority>,<weight>
# If the domain part if missing from the name (so that is just has the
# service and protocol sections) then the domain given by the domain=
# config option is used. (Note that expand-hosts does not need to be
# set for this to work.)
# A SRV record sending LDAP for the example.com domain to
# ldapserver.example.com port 389
#srv-host=_ldap._tcp.example.com,ldapserver.example.com,389
# A SRV record sending LDAP for the example.com domain to
# ldapserver.example.com port 389 (using domain=)
#domain=example.com
#srv-host=_ldap._tcp,ldapserver.example.com,389
# Two SRV records for LDAP, each with different priorities
#srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,1
#srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,2
# A SRV record indicating that there is no LDAP server for the domain
# example.com
#srv-host=_ldap._tcp.example.com
# The following line shows how to make dnsmasq serve an arbitrary PTR
# record. This is useful for DNS-SD. (Note that the
# domain-name expansion done for SRV records _does_not
# occur for PTR records.)
#ptr-record=_http._tcp.dns-sd-services,"New Employee Page._http._tcp.dns-sd-services"
# Change the following lines to enable dnsmasq to serve TXT records.
# These are used for things like SPF and zeroconf. (Note that the
# domain-name expansion done for SRV records _does_not
# occur for TXT records.)
#Example SPF.
#txt-record=example.com,"v=spf1 a -all"
#Example zeroconf
#txt-record=_http._tcp.example.com,name=value,paper=A4
# Provide an alias for a "local" DNS name. Note that this _only_ works
# for targets which are names from DHCP or /etc/hosts. Give host
# "bert" another name, bertrand
#cname=bertand,bert
# For debugging purposes, log each DNS query as it passes through
# dnsmasq.
#log-queries
# Log lots of extra information about DHCP transactions.
#log-dhcp
# Include a another lot of configuration options.
#conf-file=/etc/dnsmasq-resolvconf.conf
#conf-dir=/etc/dnsmasq.d
domain-needed
interface=lo
# If dnsmasq is compiled for DBus then we can take
# advantage of not having to restart dnsmasq.
enable-dbus
conf-file=/etc/dnsmasq-conf.conf
resolv-file=/etc/dnsmasq-resolv.conf
Logs:
May 23 00:01:06 panzor systemd[1]: Failed to start A lightweight DHCP and caching DNS server.
May 23 00:01:10 panzor dhcpcd[27267]: dhcpcd not running
May 23 00:01:10 panzor kernel: [ 7771.282756] iwl4965 0000:03:00.0: Can't stop Rx DMA.
May 23 00:01:10 panzor dhcpcd[27294]: dhcpcd not running
May 23 00:01:11 panzor dhcpcd[27330]: dhcpcd not running
May 23 00:01:14 panzor dhcpcd[27373]: wlan0: sendmsg: Cannot assign requested address
May 23 00:01:18 panzor dhcpcd[27373]: wlan0: sendmsg: Operation not permitted
May 23 00:01:22 panzor dhcpcd[27395]: wlan0: sendmsg: Operation not permitted
May 23 00:01:26 panzor dhcpcd[27395]: wlan0: sendmsg: Operation not permitted
For domain filtration, if I remember correctly, I am using this
https://bbs.archlinux.org/viewtopic.php?id=139784

How can I sync my photo contents in iPhoto on my iMac to my new iPAD's iPhoto? I follwed all the instructions on manuals for both iPAD and iTunes re syncing, but I cannot find "phone button" under Device name on iTunes page. Please help! Thanks!

I follwed all the instructions on manuals for both iPAD and iTunes re syncing, but after physically connecting iPAD with iMac with USB or via WiFi I still cannot find "phone button" under Device name on iTunes page. Please help! Thanks!
I have been creating a photo book using a lots of photographs on iPhoto, and then I took another photos by using new iPAD which I want to integrate with the original album/book on iMac. I was able to import them from iPAD's iPhoto to iMac's iPhoto. However I cannot import or transfer or sync anything from iMac's iPhoto to that of my iPAD.
So my iPhoto page on iPAD contains only 3 or 4 newly created albums, and no other info. That means no syncing....
I am supposed to be able to work on this project on either of these iPAD and iMac, correct?
I am puzzled. I appreciate for your advice and help.
Thank you!

It doesn't appear under the iPad device on the left-hand sidebar of iTunes, you need to select the iPad device on the sidebar and then select the Photos tab on the right-hand side of iTunes e.g.
And then on the right-hand side :

Clients fail to resolve local DNS names, external names working fine

Hi there,
I've a strange issue with a couple of domain joined computers. Resolving internal and external host names works fine with nslookup. But clients loose AD connectivity because they can't resolve host names from the local DNS zones outside of nslookup.
Pinging IP addresses always works.
So far only notebook computers are affected. Desktop computers work fine. OS is Windows 7/8/8.1 for clients and Windows Server 2008 R2/2012 for AD DCs/DNS servers.
Example:
C:\>nslookup bl-sphv00
Server: bl-spdc01.bl.local
Address: 192.168.154.21
Name: bl-sphv00.bl.local
Address: 192.168.154.10
C:\>ping bl-sphv00
Ping request could not find host bl-sphv00. Please check the name and try again.
C:\>ping bl-sphv00.bl.local
Ping request could not find host bl-sphv00.bl.local. Please check the name and t
ry again.
C:\>ping 192.168.154.10
Pinging 192.168.154.10 with 32 bytes of data:
Reply from 192.168.154.10: bytes=32 time=52ms TTL=128
Reply from 192.168.154.10: bytes=32 time=51ms TTL=128
Reply from 192.168.154.10: bytes=32 time=52ms TTL=128
Any help appreciated.
Thanks a lot.
Te.Be.

Hi there,
a Microsoft support guy send me a solution earlier posted under
http://social.technet.microsoft.com/Forums/windowsserver/en-US/f49b8398-d923-4e7e-86e7-78094113c091/problems-with-dns-and-ad?forum=winservergen
To get the client work again you just have to delete a few registry keys set by DirectAccess GPOs using this little batch:
@echo off
reg delete "HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows NT\DNSClient\DnsPolicyConfig" /f
reg delete "HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\Policies\Microsoft\Windows\NetworkConnectivityStatusIndicator\CorporateConnectivity" /f
reg delete "HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\Policies\Microsoft\Windows\Tcpip" /f
reg delete "HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\NetworkConnectivityAssistant\DTEs" /f
reg delete "HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\NetworkConnectivityAssistant\Probes" /f
reg delete "HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\LanmanWorkstation\Parameters" /v SMB1NATCompatibilityLevel /f
Unfortunately this breaks the clients DirectAccess configuration and leaves me without a real solution. Found some hints here:
http://blogs.technet.com/b/tomshinder/archive/2010/03/13/uag-directaccess-group-policy-assignment-make-sure-the-right-policies-are-applied.aspx
So my question is now: How do i have to edit the wizard generated DirectAccess GPOs correctly?
Anyone any idea?

Still cannot resolve "gethostbyaddr() and reverse DNS name" warnings.

Similar Messages

Maybe you are looking for