These problem about features in Cisco PI 1.2
Dear Cisco Support Team ,
Currently , I am using PI 1.2 .I have some confuses about these features on this .
1. Alarm and Event :
- When 1 port on any devices down , I don't see any alarm about this . Plz tell me What kinds of alarm in PI ?
- I can't receive any syslog on these devices although I have configured and received on LMS .
2. Client and Users :
- What is the client ? On some Switchs just has 24 ports but show more 24 clients .
Thanks!
Hi Predrag ,
Thanks for advisors .
- About the syslog :
I have configured syslog on device to send to PI , some devices can send to PI , almost switchs .We monitor 40 devices , have 9 switchs in the network but on PI just see syslog on 2 switchs , no syslog on all router ? The flowing is status on PI :
Last login: Mon Apr 8 14:08:41 2013 from 10.7.15.224
srv-pi-01/admin# ncs status
Health Monitor Server is running.
Reporting Server is running
Ftp Server is running
Database server is running
Tftp Server is running
Matlab Server is running
NMS Server is running.
SAM Daemon is running ...
DA Daemon is running ...
Syslog Daemon is running ...
status
- About the Client :
For example :
I have 2 switchs . They have connected ( Switch A-- Switch B on port 24 ). On 1 switch A have connect 1 router A , from router A connected router B .
When I show client on PI on Switch B I see router B as client although it not connect with Switch B .
Plz help to check this problem .
Regards
Similar Messages
-
nowadays have many user have problem with update to ios7 and need active with apple id maybe in the future in order escape from these problems must be stop use these products else. Because of simple user don't know about this technology and sometime just hear from other user that it 's difficult to use then force they change phone that use to handle to another.
It is a feature to discourage the theft of iPhones by making them useless if resold. It's not going anywhere. It's simple: just don't buy a phone until you make sure that the activation lock has been disabled.
-
I need some detail solutions and suggests about below these problems ?
I need some detail solutions and suggests about below these problems:
Problem 1: SAP Management Console cannot start successfully
Problem 1.1: Click on SAP Management Console, but yellow light continues for a long period of time.
Problem 1.2: In DOS, startsap command cannot start SAP R/3.
Problem 1.3: Oracle 9i database automatically shutdown by itself.
Problem 1.4: There is very low disk storage left (say less than 50MB) in the hard disk where Oracle 9i database is installed in the server.3.1 - If you client copy from client 000, you need to go to SCC4 and set the client to customizing chnages allowed;
3.2 - If you do a client copy from client 800 (the one that SAP delivers data in) you should have data. Client 000 is empty (almost).
3.3 - You should be able to change the password of SAP* PASS user.
I am not sure which version you are dealing with, but ERP2004 and ERP2005 allow you to change the password suring installation.
Also, there is a parameter that can be maintained that allows you to log on as SAP*. If you set as not available, no one can log on.
Hope it helps,
Leonardo De Araujo -
Any one else have these problems with Mavericks 10.9.3?
I've observed the following wiith Mavericks:
If the system has multiple user accounts on it, it will start, erratically it seems, running background processes with those user IDs. With com.apple.IconServicesAgent eating up sometimes nearly 300MB of memory, this can get to be a memory wart hog.
It appears to be using about 20% more memory.
The fans are coming on a lot more, indicating the CPU is being taxed.
Erratically and inconsistently "losing" external drives on sleep.
High levels of memory compression when there was none before.
I reported on item #1 last night with this link:
https://discussions.apple.com/message/25807061#25807061
I monitor system activity with a tool named Performance Probe which shows the memory usage the old way (pie chart) and then bring up Activity Monitor to get the deteails. After rebooting one time, Performance Probe showed nearly 3GB out of 4GB of memory in active use right after booting, this used to report less than 2 GB. The exact same thing happened as in the link above, but in this case every single user account on the system had an instance of cfprefsd, launchd, distnoted, and com.apple.IconServicesAgent with IconServicesAgent being the "Grandaddy" of memory consumption. I used Activtiy monitor to kill all the launchd processes in the unused (not logged into) accounts followed by the rest and they never restarted.
Observation: For some reason the OS seems to erratically decide to launch or not launch all these other user accounts. Sometimes Activity Monitor will just show me and the normal system accounts on the sytem, other times it appears to be more or less a crap shoot as to what processes have been started under what users name.
For item 2, normally 10.9.2 was showing about 2.1G of RAM in use now it's running about 2.4-2.5GB. All that I typically have running is Safari and Mail and thats when I noticed this increase.
Item 3 is just an observation, but it tells me the CPU is doing a lot more work to do the same things it did before.
For item 4, I'd heard of this before but I'd never seen it, until now. If external drives are connected to the system and the system goes to sleep, when you wake it up the OS will say the drive and it's volumes were incorrectly ejected. This happens erratically on USB drives. To simulate it I set the sleep interval at 3 minutes and let it go to sleep several times. Sometimes the drives would be there, sometimes I'd get the unmounted message. I should also note that the first time I rebooted Mavericks after the update it didn't see my Firewire external drive but has since then.
I noticed item 5 after using Safari and Mail for a while. The system more or less came to a crawl, fans came on high speed, Perfomance Probe was showing about 3GB of RAM used (RED) with the other 1GB completely blue, which means it's not active but swappable. This was weird because I'd never seen the system "pegged" like this. Usually there's free memory showing up. I opened up Activity Monitor to get the details and it showed that about 1GB of RAM was compressed. This has never happened before. The only things in use were Mail and Safari, and I'd guess I was probably using Safari to go to weather.com.
I have never had or witnessed any of these problems before.An update:
For item 1, I suspect that when the other accounts were used, the users left them in the modes to reopen applications etc when restarting. This is a laptop and it's shared in the field by several people. By getting everyone to log into the accounts and turn that feature off, it limited the number of automatic processes that would restart. By opening up Activity Monitor, and first killing launchd for each of these unused accounts, then the rest of the processes, it seems to have cleared that problem up. This system has been through several OS upgrades so it's quite possible some people may not have used this thing since Lion or Mountain Lion were on it. I am, of course, talking about killing launchd associated with people not using the system, not an active version of it.
As far as items 2, 3, and 5 go, any time Safari needs to run some video this problem seems to surface. It doesn't seem to happen with other browsers. -
Some problem about SAP R/3 ~ I need some detail solutions and suggests
I need some detail solutions and suggests about below these problems:
Problem 1: SAP Management Console cannot start successfully
Problem 1.1: Click on SAP Management Console, but yellow light continues for a long period of time.
Problem 1.2: In DOS, startsap command cannot start SAP R/3.
Problem 1.3: Oracle 9i database automatically shutdown by itself.
Problem 1.4: There is very low disk storage left (say less than 50MB) in the hard disk where Oracle 9i database is installed in the server.
Problem 2: Problems in User Maintenance and Security of the SAP R/3 System
Problem 2.1: Super user account password was lost (e.g. SAP* password was lost)
Problem 2.2: Super users DDIC and SAP* were dropped in table usr02 in Oracle.
Problem 2.3: Some users have been locked or deleted by an ABAP programmer who has been granted with almost superuser profiles. For example, an ABAP programmer has been granted a profile of SAP_ALL and SAP_NEW but the system administrator would like to restrict all programmers form using SU01, SU02, SM01, so that no programmers can maintain other user's accounts.
Problem 3: Problems in the configuration of client copy
Problem 3.1: A copied client from the Client 000 cannot be customized.
Problem 3.2: No sample data in IDES after a successful client copy.
Problem 3.3: Logging on without being authorized. A new client is created and client copied and transported successfully. However, anyone can log into the system using user SAP* with the default password PASS.
Problem 4: Problems in the installation of SAP R/3 Server
Problem 4.1: Computer Name of the SAP R/3 server has been changed after the full installation of Oracle 9i and SAP R/3.
Problem 4.2: A network card of a server was faulty and it was replaced by a new network card but the SAP R/3 license was expired.
Problem 4.3: You would like to reinstall SAP R/3 on a server which has previously installed with SAP R/3 but the same error message appears during the re-installation.
Problem 5: Problems in the backup and recovery of Oracle 9i Database
Problem 5.1: A redo log file was lost and the database could not be started.
Problem 5.2: A group of data files were accidentally deleted and the database could not be started.
Problem 5.3: Both the online redo log files and archived redo log files have been damaged.
Problem 6: General problems regarding the general operations and the connection to the SAP R/3 System
Problem 6.1: After a reboot of the Windows 2003 Server, SAP service is not automatically started.
Problem 6.2: Some users complained that the performance of SAP R/3 is really very slow.
Problem 6.3: A user complained that his/her password was correct but he/she could not lock on the client because it was locked.Problem 2
2.1 If user account of the sap* is lost u can retrive by loging into os level as sidadm type this command
DELETE SAP<sid>.USR02 where BNAME='SAP*' AND MANDT=100
This 100 is the client in which u want to delete the sap*
after that restart the server and login as sap* with the default password as pass
there is also another way of doing this if needed u can catch me at [email protected] -
Is there going to be a new update to 2.0 that fixes these problems? When?
Hi, as my problems are iPod AND iTunes based, am posting question in both forums.
I have a few problems that I need addressing as soon as possible, as day to day use of my iPod has got incredibly aggravating.
When I access iTunes, I am immediately prompted to put my password in (for Apple id). It doesn't store it so if I want to purchase something, I have to put in my Apple id and password. If I've just done something in the iTunes store like purchasing something, then go to look at my account, I need to type in my password again. If I buy something, then try and buy something straight after that, I need to type in my password again. You get the idea.
Another iTunes issue - it's **** slow at the moment and I know it's not my internet speed. iTunes was fine before the 7.7 update, but now I experience very slow loading times, lots of errors with connecting to the store, downloads having errors etc. More often than not, downloads are at a speed like 3kbps. After many many attempts, I succeeded in downloading and reinstalling the 2.0 update, for reasons I will get to. I can't begin to count the number of times that failed before I succeeded.
Backing up - every time I connect my iPod, it backs up. Synching takes a long time. Synching and installing apps takes ages, it even takes ages to synch Outlook info. I know it's not my USB because other media players are fine.
The device itself:
- bootup time is very long. Several minutes.
- accessing settings, Notes, contacts, clock etc is slower than before.
- freezing. A couple of days ago, it froze in settings. I attempted to turn off, which it couldn't do. I rebooted it, which worked, but the black screen with the white apple logo was on the screen for about ten minutes before the device turned on again.
- battery drainage is mysteriously quicker since the update installed.
I'm not happy and would like to know a projected release date for an update to fix all these problems, which I know I'm not alone in.The best advice I can offer for your iTunes problems is to try creating a new test user on your computer. Check to see if iTunes behaves the same way in the new user.
As for your iPod issues, you should try restoring your iPod via iTunes, erasing all software and content components on the device. Once the device is restored, do not restore from backup and do not sync any of your content.
You mentioned that you use Notes and Contacts. You want to make sure that you email yourself your notes from the application and assure that you've got all your contacts synced with your computer.
Use the iPod in its restored state for a few hours. If you notice a favorable difference, begin to start syncing your content back over.
Good luck! -
How do I fix these problems with my iPhone 4S?
Okay, so I recently purchased a LifeProof case for iPhone 4S to take underwater photos and videos. Upon my third or fourth submersion, I discovered that water (very small amounts) had entered the case via the dock connecter area. I immediately removed the phone from water, dried it off and left it for about an hour. I (incorrectly) thought that my phone was completely dry and made the huge mistake of charging my phone. I returned an hour later to a funny smell and a very unhappy iPhone.
My current problems include a malfunctioning home button (activating siri on it's own and being unresponsive most of the time), a disappearing volume bar in music, youtube etc. (no volume without using a dock) and charging problems (doesn't charge from time to time). All of these problems seem to affect each other and we can go ahead and assume it's as a result of water damage.
I will be working out some way to get these issues professionally repaired (some clues as to where to go would be lovely), but I can't see to that for at least a week and a half. Are there any temporary (or permanent for that matter) fixes that i can do relatively easily? (not jailbroken)The only possible fix was turning the phone off immediately and burying it in a bag of dry rice for a week at least. That might...just might...have worked. But you're way beyond that and I see no fixes. In fact the phone is probably going to get more problems before finally gving up the ghost. Continued use is just shorting out more and more of the circuitry. For that reason I don't think repair is much of an option. Go to an Apple Store and buy an out-of-warranty replacement.
-
hi everyone, i have a problem about my iphone 4S, doesn't work with wifi connection and bluetooth since upgrade to the IOS 7.0.3. Can anyone can help me tosolve this problem?????Thank's regards paulus
Try the suggestions here to see if they resolve your problem:
http://support.apple.com/kb/ts1559
If these don't work you may have a hardware problem. Visit an Apple store for an evaluation or contact Apple Support. -
Hello apple
I have the problem with my iPhone and my friends have this problem too.
My iPhone have the problem about calling and answer the call. When I use my iPhone to call I can't hear anything from my iPhone but the person that I call can answer it but when answer both of us can't hear anything and when I put my iPhone to my face the screen is still on and when I quit the phone application and open it again it will automatic call my recent call. And when my friends call me my iPhone didn't show anything even the missed call I'm only know that I missed the call from messages from carrier. Please check these problem I restored my iPhone for 4 time now in this week. I lived in Hatyai, Songkhla,Thailand and many people in my city have this problem.
Who have this problem??Apple isnt here. this is a user based forum for technical questions. The solution is to restart, reset, and restore as new which is in the manual after that get it replaced for hard ware failure. if your within your one year warranty its replaced if it is out of the warranty then it is 199$
-
Should I get an iMac with all the problems about?
So, as my birthday is coming up I decided to get an iMac, however on Wednesday I read on Gizmodo about the yellow screen debacle, so after doing some research on the matter I'm not sure what to get any more.
I decided (Before I read this on Giz) to get a 21.5" iMac.
So I have a few questions about it.
1: Does the 21.5" iMac's screen flicker and blackout like the 27", it's very hard to find info about it as it seems it only affects 27", but is that because it doesn't effect 21.5" or because not many people bought the 21.5" iMac
2: Just how bad is this 'yellowing', I've looked at various photos of it and can hardly see any problem, does anyone have a really bad screen with the bottom of the screen being strongly yellow tinted?
3: Should I just skip all these problems and get a Macbook?
Please help me decide!You have done your research on the new iMacs so you already know the answers to your questions. It's difficult to come to a consensus though because some report problems and some report they have no problems. It's your birthday... in my honest opinion, go for it.
Post back when you have your machine as to your findings on your machine. That's the one that matters.
Sorry if I am sounding a little tired of this but many people have asked the same question and many have provided the same answers. If you are very conservative you might want to wait and see, but if you don't want to postpone your birthday, go ahead; your iMac may be fine and if not, Apple will make it right. Do buy AppleCare. -
Dear all,I have a problem about vrrp,my core switch is cisco 3750x and huawei S5700-28C-EI, after I configured vrrp between them,the switch log got the error problem as follow:
*Jan 11 00:01:43.111: %VRRP-6-STATECHANGE: g1/0 Grp 3 state Backup -> Master
*Jan 11 00:01:43.111: VRRP: tbridge_smf_update failed
*Jan 11 00:01:44.187: VRRP: Advertisement from 10.252.200.34 has an incorrect group 10 id for interface g1/0
*Jan 11 00:01:46.539: VRRP: Advertisement from 10.252.200.36 has an incorrect group 10 id for interface g1/0
*Jan 11 00:01:50.323: VRRP: Advertisement from 10.252.200.34 has an incorrect group 10 id for interface g1/0
*Jan 11 00:01:51.707: VRRP: Advertisement from 10.252.200.36 has an incorrect group 10 id for interface g1/0
*Jan 11 00:01:52.079: VRRP: Advertisement from 10.252.200.34 has an incorrect group 10 id for interface g1/0
*Jan 11 00:01:53.079: VRRP: Advertisement from 10.252.200.34 has an incorrect group 10 id for interface g1/0
If cisco and huawei cannot interconnect with each other?Can you post the interface config from the huawei and cisco device?
HTH,
John
*** Please rate all useful posts *** -
A problem about Chinese encoding
When i access portal by SSL,I find one or two problems about encoding.
reshow these problems:
1. Locale be set to Chinese(zh_CN)
2. access portal by SSL
3. Administration/create portlet
Then the popup window's title will show a bad encoding.
otherwise,if i search chinese, then only have bad encoding shown in the searchbox and i can't get anything.
MY running enviroment:
windows 2003
plumtree foundation v6.0
plumtree publisher v6.2
tomcat 5.0.58 with jre_1.4.2.08
MSSql 2000 sp4
and I have tried other BEA ALUI newer version,I can get these problems.
I'm appreciated for any help.ANSI 0xFF is NBSP. NBSP in Unicode is 0x00A0... so neither 0x00FF (which is �) nor 0xF5F8 (which is in the "private use" range) is correct. Something really weird is going on.We are talking about CP1252 and in CP1252 0xFF is �
(see http://czyborra.com/charsets/iso8859.html for example) and thus is \u00FF correct.
btw. I would never use windows notepad as reference application. -
hi everyone:
I have a problem about ALV. The question is I want to show two headers in the gt_item .(Hierachy)
I want to use these in the event "change_fieldcatlog"
LOOP AT I_FIELDCAT.
CASE I_FIELDCAT-FIELDNAME
WHEN 'MESSWERT'.
I_FIELDCAT-ROW_POS = 1.
I_FIELDCAT-SEL_L = '1111'.
I_FIELDCAT-SEL_M = '1111'.
I_FIELDCAT-SEL_S = '1111'.
APPEND I_FIELDCAT.
so I want to add another label in the next row. but I write like this below , it doesn't work .
I_FIELDCAT-ROW_POS = 2
I_FIELDCAT-SEL_L = text-004.
I_FIELDCAT-SEL_M = text-004.
I_FIELDCAT-SEL_S = text-004.
APPEND I_FIELDCAT
ENDCASE.
ENDLOOP.
So who can help me ?
thank you in advacne .
Regards
NickHii Nick, in your program I found that you have created only one fieldcat structure, actually we need 2 structures one is for workarea and one for body.
like this
It_Fieldcat type SLIS_T_FIELDCAT_ALV
Is_Fieldcat type SLIS_FIELDCAT_ALV
now you can write the code
LOOP AT It_FIELDCAT into Is_Fieldcat.
CASE Is_FIELDCAT-FIELDNAME
WHEN 'MESSWERT'.
Is_FIELDCAT-ROW_POS = 1.
Is_FIELDCAT-SEL_L = '1111'.
Is_FIELDCAT-SEL_M = '1111'.
Is_FIELDCAT-SEL_S = '1111'.
APPEND Is_FIELDCAT to It_Fieldcat.
clear Is_Fieldcat.
Is_FIELDCAT-ROW_POS = 2
Is_FIELDCAT-SEL_L = text-004.
Is_FIELDCAT-SEL_M = text-004.
Is_FIELDCAT-SEL_S = text-004.
APPEND Is_FIELDCAT to It_Fieldcat.
Clear Is_Fieldcat.
Hope it will works.
Reward points if helpful. -
PI7.0: Problem about openning alert configuration in RMB
Hi experts,
I encounter a problem about alert configuration.
I have defined the alert catogory in WAS ABAP and use the report RSALERTTEST to test it. It's OK. Then I logon RWB and click u201CAlert configurationu201D,system popup a login window. I input my user account and confirm it. But the logon window popup again and again.I don't kown how to resolve it. BTW, my user account has the roles SAP_ALM_ADMINISTRATOR and SAP_ALM_CUSTOMIZER.And I have resolved the problem "Alert configuration does not start" according to note 750287.
Anyone has idea??Could you please give me some advice???
Thanks a lot in advance.
BR Villy.LHello Villy
Check these notes:
1) #913858 XI Alerting: Troubleshooting
2) #768456 Troubleshooting Runtime Workbench
Restart the java engine after making any changes in the Exchange Profile.
For further info check previous threads on this topic:
The URL contains no complete domain specification
Calling the BSP page terminated due to an error While accessing ALERT INBOX
Regards
Mark -
im totally on hold after reading all these problems with the MBP SR. I thought long and hard and though my money is already paid in full Im not going for it yet! Might wait till Leopard is in it. Anyone having NO PROBLEMS!?
I've had my MBP 2.4GHz for 3 weeks now, and I love it.
I have had NO PROBLEMS whatsoever.
It does seem to get very hot sometimes, and it worries me a bit, but apparently this is "normal".
There is no screen "flicker".
When I wear headphones, there are some barely noticeable electronic noises that are normal for an electronic (non hi-fi) device such as this, and a non-issue for me even as someone from an audio engineering background.
I have seen the yellowish tint to the screen some have reported, but ONLY WHEN VIEWING FROM AN EXTREME ANGLE!
This is a normal limitation of the technology and certainly not a defect.
I come to this forum to find out what potential issues I should watch out for.
I take all the negative reports with a grain of salt, knowing that they are typically far more rare than posts here would make it seem.
You need to do your research, and realize that if a dozen folks report a problem, that is a fraction of a fraction of a percent of users.
The ones to pay attention to are the ones with much larger numbers of reporters, such as this one http://discussions.apple.com/thread.jspa?threadID=986785&tstart=15 - about AirPort related kernel panics, which seems to be a very hardware-specific bug that doesn't happen to relate to me.
I assure you, there are many more people, like myself, who are thrilled with their MBP purchases, than the ones that are having major problems - they just don't have a reason to post here.
Also keep in mind that the unlucky few who do purchase a legitimately defective machine are understandably frustrated and angry. And it's human nature to want to believe that you are not just one of the unlucky few - misery loves company.
So a lot of these folks try to convince themselves and others that the problems are wide-spread. Which, for the most part, they are not.
Anyway, all that said, if you can comfortably wait until Leopard is released to buy your MBP, you absolutely should.
My aging PBG4 couldn't run the software I'm being trained to use (FCP), so I couldn't wait any longer.
It took every ounce of restraint I could muster to wait for the new MBP.
I waited an extra couple of weeks after it was released, keeping an eye on these forums, just to rule out any major defects - which I did, despite the handful of reports that the sky was falling.
At the rate technology improves and prices fall these days, it definitely pays to wait as long as you possibly can to make a high-end tech purchase (as difficult as it is to delay gratification).
So - never fear - these machines are awesome! You can buy with 99.9% certainty that you'll be thrilled with your purchase.
Sorry for the long post. Wait for Leopard if you can, if not buy without fear and ENJOY!
-Dennis
MacBookPro2.4GHz 15.4" matte, PowerBook G4 Ti 550 [FOR SALE], PowerMacG4 466 Mac OS X (10.4.10) 3rd gen iPod 30gig, 2nd gen Nano 8gig
MBP 2.4GHz 15" Matte, PowerBook G4 Ti 550 [FOR SALE], PowerMac G4 466 Mac OS X (10.4.10) 3rd gen iPod 30gig, 2nd gen Nano 8gig
Maybe you are looking for
-
Hi! At some point over the winter break (I am a professor) Buzzword stopped working on my office computer (Max OSX 10.5.6., Firefox 3.0.5 and Safari 3.2.1, Flash Player 10,0,12,36, ). I try to login to Buzzword, either from the acrobat.com applicatio
-
WF_Batch id deletes cost center from euipment master data - IE02
hi guys, how to trace this.. we have checked some of our equipment master data that wf_batch id has deleted its cost center..how can we work from this..how to trace which programs/function did it.. is it purely coming from workflow ?
-
I am having problems backing up data with DPM 2012. I keep getting this meesage. The protection agent on dpmServer was temporarily unable to respond because it was in an unexpected state. (ID 60 Details: Internal error code: 0x809909B0) I can't under
-
I'm having a problem during locating my iPhone via Find My iPhone app & iCloud service online. I've enabled everything needed by Find My iPhone app but it stil doesn't work. I live in Serbia, we don't officialy have iPhones, but there is no law forbi
-
HP color laserjet 4600 parallel port is wierd need help to identify
Hi I have a laserjet 4600 and it has a wierd looking parallel port and I can't seem to find out the name for it so I can buy it online. I have tried looking for it online but the only thing that comes up is the IEEE 1284 36 pin parallel port. Can any