Tiger 10.4.6 + Logic 7.2 + digi 001 no worky...HELP!!

hi there,
so i received updates last night and installed.
- tiger 10.4.6
- logic 7.2
- g4 dual 1.25 ghz with 1.25 ram
so i've been using my digi 001 as my soundcard, running coreaudio. after installing everything last night, the 001 was not being seen by the version of coreaudio i had, think it was 6.4. so i upgraded that to coreaudio 7.0. still no luck with the 001. read on a thread this morning that coreaudio 7.0 doesn't support the 001. ah, yet another notch in my 'i hate digidesign' belt.
so, in this thread it said coreaudio 6.9.2 worked with the 001 AND tiger. so i trashed coreaudio 7.0 and grabbed 6.9. installed, and when firing it up, it at least recognizes the 001, but says it's in use, though i see nothing else open. any thoughts here?
another item:
i use a hd24 to track all my live audio and use logic primarily for mixing and virtual instruments. i could get by without the 001, what sound cards would you folks recommend? and they don't even have to have audio in capabilities.
thanks! hope someone can help!
andrew

ah, david, you're the post i saw earlier! yay! ok, so i do always fire up coreaudio first. usually it's all systems go, but last night/today, no dice. i just completely shut down and rebooted. only think i've fired up is coreaudio, it says:
digidesign hw: digi 001
status: not connected (hw in use)
and the hw setup button is not active. i did open up the audio/midi utility and the 001 is there and have it selected as my defaults.
what do you suggest?
THANKS!

Similar Messages

  • Logic 7 with Digi 001

    Hi all, first time in this forum. I am using a QS g4 on 10.3.5 with a digi 001, apogee rosetta and a SwisSonic lightpipe to analog i/o. I am able to easily achieve 18 in & 18 out with this setup using pro tools LE 6.4 and digidesign core audio setup 6.4.
    Again, 18 I/O is no problem using pro tools, but logic will only recognize 12. I'm nervous about updating the OS and the Core audio, since everything is super stable, but if someone tells me that this is the fix I will.
    Quicktime is version 6.5.1. I'm not sure if that's pertinent, but why not include it.
    Thank you for any advice in advance!

    Just test it on a copy of your system (another hard drive). It probably will only make things worse-soon enough you'll realize you are in th market for another audio card. If it is because of Digi's audio driver you get 12 then I don't even think they updated the 001 after that release, or? If it is then odds are even further against you. I'd just say, take an hour and test it out.

  • Digi 001 Core Audio Manager and Logic 7.1

    I just upgraded to Pro 7.1 from logic 5.5.1. When I would start up 5.1.1 it would automaticly startup the coreaudio manager for the Digi. I've noticed now using 7.1 that I have to start the Digi Core Audio Manager before starting up Logic Pro or it will not recognize the Digi at all, and will remove the digi as a sound card selection. Does anyone else experience this same issue? Is it normal? I read into the logic help and it said with a TDM or HD digi hardware this would be necessary. I'm confused help would be appreciated.

    Yes, this is normal when using Logic Pro 7.1 and Digi Coreaudio version 6.4. They seem to have fixed this in more recent versions of the coreaudio manager, but 6.4 is the last revision supported by the Digi 001.

  • Logic Gold 5.5.1 and Digi 001

    After formatting my computer, logic and digi 001 wont communicate in OSX anymore. I have installed both OS 9 and OSX, and in OS 9 it work fine. But when i try to launch Logic (5.5.1) in OSX i get this error message: Error code 28519 was returned buy the core audio driver...
    The Core audiodriver is installed in Library/audio/plugins/HAL! But i have no clue about SystemInit and Direct I/O (versions or were to put the files on the computer.
    I have also tried with and without the Protools software installed but that did´nt work either.
    PLEASE someone, help me. I have tried and tried but nothing seems to work. Before the formatting everything worked fine, but not anymore...
    What´s wrong?

    Hi,
    Why exactly did you format your computer?
    Did Logic Gold 5.5.1 work on you OSX BEFORE you reformatted?
    What changed from before your format to after (any driver versions changed/automatic updates?)
    Remember,Digidesign does NOT support Digi001 anymore,so which Audio driver(DAE/CoreAudio) did you use before you reformatted?
    From Digidesign's website Answerbase:
    Core Audio error 28519 when trying to use the Digidesign Core Audio driver in a third party application (Logic, Reason, etc.).
    This error can have several different causes. Some things to check:
    1. Is another application using the core audio driver, such as the Sound control panel in your System Preferences panel? If so, you'll need to quit that application or switch your Sound control panel back to built in hardware. Keep in mind the Digidesign core audio driver is single client - only one application can be using the hardware at any time.
    2. Is your Digidesign hardware turned on and powered up? You may try turning off and turning back on the hardware and restarting your application.
    Also see Answerbase #27816 for other possibilities specific to Emagic Logic:
    Getting an error message -28519 in Logic Audio 6.3. when changing to Digidesign hardware for the CoreAudio output.
    These errors can be caused by two plugins that are installed when updating Emagic's Logic to version 6.3.1
    Removing these two plugins from the plugins folder may solve the issue.
    The plugins folder is located in the
    MacHD / Library / ApplicationSupport / Digidesign / Plugins
    Remove
    - ESB TDM OSX
    - ESX 24 TDM OSX
    If these plug-ins are installed, when launching Pro Tools, you will get an error message: When attempting to launch you get either: "- 6003 Emagic system bridge error"
    or "- 6003 error while initializing TDM host streams." (see Abase # 27414). Remove the plug-ins above to solve this problem.
    Without knowing why you reformatted,it is harder to help.
    I hope the Digidesign Answerbase messages help you out.
    Cheers,
    Nick
    iBook G4 800mHz   Mac OS X (10.4.3)   640MB RAM/ProTools 6.9/LogicPro7.1.1

  • Steps to create a logical system for client 001.

    Hi,
    In client 000 go to transaction scc4. There you create your new client for sap netweaver abap trial version for BI?
    Here, can you give me steps to create a logical system with client 001 using tcode scc4.
    Thanks,
    Kannan

    hi
         First log on to SAP R/3 server connections Go to SCC4 in R/3 & in Scc4 BW server. A screen opens in that logical name of the system would be opened in both (R/3 & BW).
         Take notepad in it save .R/3 & BW logical names go to R/3 & click SM59 to create R/3 connections click then a screen opens gives BW logical name in RFC Destination option & give connection. type 3 & give some description & then press enter.
         You will get another screen under it then at target host gives BW server name we will get it from BW logon change ID, IP address option & give the system no. The system no go to logon pad just drag it then you will see the name.
         Then click on log on securities go to log on give BW server details like No, client user Password. Then save it then click test connection tab if there are errors then it gives yellow color if they are no error the whole thing come as white.
         Then click on the Remote Logon then we go to BW server give RFC – SM59 & click create. Then give the server name which is at the bottom right corner give it then give the no, name, password in logon Security save it & test connection & then remote logon.
         R/3 - B W - R/3
         Logical connection source system connection is used to transfer the data from R/3 to BW. Go to BW system& click RSA1 go to source system option go to top to the source systems right click on it. Then click create then a screens opens then.
         PC Flat file ,  DB  Database
         Select the option manual then a screen appears RFC Destination, Logical source name then click OK  then it goes to opens other screen save it test connection then remote login then it go back to the then a screen opens then click only activate.
         BW  RS1  SOURCE SYSTEM  CREATE MANUAL AUTOMATIC CELL
         R/3  Test connections login  back  replicate method  active data R/3 Source system you will able to.
    regards
    ashwin

  • Logical system for client 001 for SAP NETWEAVER ABAP TRIAL VERSION for BI

    Hi,
    I have installed SAP NETWEAVER ABAP TRIAL VERSION for BI. In that I have to create logical system for client 001. I have taken a list of available clients from the abap R3 side. Here is a list of it.
    Clients View
    Cl. Name City Crcy
    000 SAP AG Konzern Walldorf EUR
    001 Auslieferungsmandant R11 Kundstadt USD
    066 Test EarlyWatch Profiles Walldorf EUR
    I cannot get inside the BW side for it asks me to create a logical system for client 001. What to do?
    Kindly help me.
    Kannan

    hi,
    ? First log on to SAP R/3 server connections Go to SCC4 in R/3 & in Scc4 BW server. A screen opens in that logical name of the system would be opened in both (R/3 & BW).
    ? Take notepad in it save .R/3 & BW logical names go to R/3 & click SM59 to create R/3 connections click then a screen opens gives BW logical name in RFC Destination option & give connection. type 3 & give some description & then press enter.
    ? You will get another screen under it then at target host gives BW server name we will get it from BW logon change ID, IP address option & give the system no. The system no go to logon pad just drag it then you will see the name.
    ? Then click on log on securities go to log on give BW server details like No, client user Password. Then save it then click test connection tab if there are errors then it gives yellow color if they are no error the whole thing come as white.
    ? Then click on the Remote Logon then we go to BW server give RFC – SM59 & click create. Then give the server name which is at the bottom right corner give it then give the no, name, password in logon Security save it & test connection & then remote logon.
    ? R/3 - B W - R/3
    ? Logical connection source system connection is used to transfer the data from R/3 to BW. Go to BW system& click RSA1 go to source system option go to top to the source systems right click on it. Then click create then a screens opens then.
    ? PC ?Flat file , DB ? Database
    ? Select the option manual then a screen appears RFC Destination, Logical source name then click OK then it goes to opens other screen save it test connection then remote login then it go back to the then a screen opens then click only activate.
    ? BW ? RS1 ? SOURCE SYSTEM ? CREATE MANUAL AUTOMATIC CELL
    ? R/3 ? Test connections login ? back ? replicate method ? active data R/3 Source system you will able to.
    hope it helps u
    Ramesh

  • HT1338 Macbook pro two days old...bought logic from app store...logic has installed partly each time i open it up it wants to download rest of programme then stops half way thru and gets error message 'logic is unable to continue with download' help neede

    Macbook pro two days old...bought logic from app store...logic has installed partly each time i open it up it wants to download rest of programme then stops half way thru and gets error message 'logic is unable to continue with download' help needed !

    Hello:
    I would trot back into the Apple store and have them fix the problem (or call Applecare with a warranty issue).  There is no sense in you wasting your time trying to troubleshoot things on a new computer.
    Barry

  • Digi 001 with FCE 3..do they go?

    Hey Gurus!
    I have a Digi 001 which I'd like to use to monitor my audio in FCE 3 as I have powered monitors connected up.
    It works fine for iTunes, but i can't get it to work for FCE. I looked for some audio output settings in the programme but no joy.
    In the Mac's system preferences>Sound, the Digi 001 is the selected audio device, and like I said iTunes, Peak and ProTools ( kinda obviously) all work with the 001.
    Any tips gratefully accepted.
    pete

    A common problem, unfortunately I don't have a definitive answer. I use Protools 6.4, core audio driver 6.4 (downloaded separately), Digi 002R, as well as FCE 1.0.1. One issue that I've found is that the core audio driver is not a multi app driver. so once launched with an app, you need to re start only launching FCE. Is that the for FCE 3? Not sure. I would try putting the audio core driver in the dock and launching FCE, you should see it kick in by making sure the arrow is on next to the core driver. Be sure you turn on you Protools hardware first of course.
    Hope this was helpful to some degree,
    Good Luck Josh Silver

  • Digi 001 and dual g4 1ghz

    I'm trying to change my system over from a quicksilver 733mhz to a dual 1ghz machine. While running pro tools on the dual machine I keep getting a dae error -6045 anyone have any knowledge about this? I'm running pro tools 6.4 as I don't know if 6.9 will work with digi 001
    thanx

    Well, you would probably have more luck going on the Digidesign forum...
    My experiences with DAE errors and Protools usually have to do with the installation. Did you install Protools LE 6.4 as a clean copy or did you copy it from another computer? Also, installing a clean copy of Protools off of the disk installs drivers for the Digi or Mbox to function...if you didn't go through the full installation process then your Digi won't work. You can't just plug it in...Protools LE requires that you have a Digidesign Protools Interface (Such as an Mbox or Digi) +in order to even run Protools+. If the Digi 001 isn't correctly installed, that would probably explain your error messages.
    Also what OS are you running? And I am pretty sure 6.9 will work with the digi 001, since I know Protools 7 supports all Digi and Mbox interfaces. I've got protools 7 so I can't give you specific information just off the top of my head... If you have a copy of 6.9 then try installing it and see if it works. After the installation the Digi 001 and Protools should be fully operational.
    After reading your post again, are you trying to copy all of your info off of your original HD on the 733 over to the dual 1 Ghz machine? If that's the case then that would explain the problem...you must install a clean version of Protools LE in order to install the drivers for the Digi 001. Without the Digi, protools won't run.

  • Tiger or Leopard for Logic Studio on my G4?

    (This is a repost from a reply in another topic) According to Apple's system requirements I need to upgrade to either Tiger or Leopard to get Logic Studio to run on my G4. Does anyone with a simlilar machine have advice of whether 10.4 or 10.5 will be my best bet? Also how do I do a "clean install" and will it make a difference. -Thanks

    Before doing a clean install please make sure you've back-up all your Songs,
    then test to see if they work,
    after they have work then you could then select the Hard-Drive from where you install L.P. 8 by double clicking onto it and use Spotlight which is at the Upper-Right of the H.D. you've just enter,
    and type Logic-Pro 8 in seconds the installed Files will appear highlight all the Files you want that comes up saying Logic-Pro 8
    Right-Click onto them then select Trash or Manually Drag them to the Trash.
    As to whether you want to use Leo or Tiger its up to you,
    I would love to use Leo however at this time it isn't fully supported by Digi Design Pro-Tools LE oo2R, so i'll have to wait before i jump in,
    therefore if you don't have wait the choose is yours, Logic -Pro 8 requires OSX 10.4.9. straight to Leo + Quicktime 7.3
    Good-Luck and a happy new-Year.
    Fr.BlayZay.

  • Logic with a digi interface

    Hello I just bought a logic studio 8. I have a Question, I was reading that some people use a digi 002 working with logic 8, I wonder if a digi 002 or a digi 003 works sincronized with all the motorized faders, gains, knobs and the little screen?
    somebody use that interfases?
    Paul.

    I just got an email this morning from Digidesign. They indicated that their hardware will not interface with Logic. Digi is only designed to interface with Pro Tools.
    I have the same problem. I have been using Pro Tools LE with a 002 surface controller. Now I have Logic 8 and have to get a different controller. I am looking at the Mackie Universal Pro or Euphonix MC.
    Good luck.

  • Logic 8 and Digi 003 with RME-ADI-2 as DA/AD converters.

    I am very new to this so, I'll do my best at explaining what I am trying to accomplish. I am running Logic 8 with a Digi 003 as my interface (connected by firewire). I just got an RME ADI-2 converter (connected to 003 via optical i/o). I have the outputs of the converter working fine to my monitors, but I can not figure out what I need to do to use the RME as a source for inputs. In Logic preferences for Audio Hardware, it does not give me the option for using the RME (only the 003).
    Any help on this would be great. Thanks in advance.

    Usually you'd create an aggregate device (Utilities Folder - Audio/MIDI set up) to create a new virtual device, into which you can combine two or more devices, including built-in audio I/O.
    But although I'm not certain (as I don't use an 003) I don't think you can create an aggregate device with an 003 (no harm in trying, though).
    As your RME is already working fine connected to the 003 via optical, presumably as the 003's outputs 9/10 (S/PDIF?), wouldn't the inputs be available also on 9/10? Doesn't the 003 support ADAT - in which case the RME's ins/outs should show up, but as part of the 003 if you cabled the RME to the 003 via the ADAT connections.
    Sorry to not have a definitive answer, but maybe try some of the above variations. Maybe an 003 user will chime in.

  • Can i control surface logic 9 with digi 002 mixer? on snow leopard 10.6.8

    Hi I'm trying to connect my digi002 mixer to use it as a control surface with logic 9, is there anyway of doing this?
    I have an RME Hammerfall DSP Multiface II, that I'm using as my main sound card, but would like to light it with the 002 and use the 002 converters as well, so that in total i get 16 channels I/O + if I could get control surface of logic with the 002 would be great.....
    I heard about the Multi-Client CoreAudio Driver, but not 100% sure if and how it works to control surface logic with 002.
    Anyone???
    Help please....
    Thx...
    G

    I assume you have working installer discs? If so here's a suggestion:
    Clean Install of Snow Leopard
    Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
         1. Boot the computer using the Snow Leopard Installer Disc.  Insert the disc into the
             optical drive and restart the computer.  After the chime press and hold down the
             "C" key.  Release the key when you see a small spinning gear appear below the
             dark gray Apple logo.
         2. After the installer loads select your language and click on the Continue
             button. When the menu bar appears select Disk Utility from the Utilities menu.
             After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
             size.)  Click on the Partition tab in the DU main window.  Set the number of
             partitions to one (1) from the Partitions drop down menu, set the format type to Mac
             OS Extended (Journaled, if supported), then click on the Partition button.
         3. When the formatting has completed quit DU and return to the installer.  Proceed
             with the OS X installation and follow the directions included with the installer.
         4. When the installation has completed your computer will Restart into the Setup
             Assistant. Be sure you configure your initial admin account with the exact same
             username and password that you used on your old drive. After you finish Setup
             Assistant will complete the installation after which you will be running a fresh
             install of OS X.  You can now begin the update process by opening Software
             Update and installing all recommended updates to bring your installation current.

  • Yet another Logic Vs.Pro Tools question. Please help!!

    Hi guys! I just arrive to the world of mac a few days ago, and I couldn't be happier. Now it's time to purchase new audio gear, and I am torn between Logic Studio/Apogee interface, or the Digi 003. I've been a Sonar user for the past couple of years, and before that I was on Cubase.
    I love Sonar, but I'm sick of PC's(hence the switch). I need something with good compositional/midi tools, but I also need powerful audio editing. One thing I love about Sonar is the ability to use non-destructive editing in the arrange window. Can the new logic do this? Currently I am leaning towards logic...but I still haven't made a decision. I definitely need drum programming ability, and I'm not sure if Pro Tools le even has a drum map? Any and all advice would be greatly appreciated. Thanks!

    servo2112 wrote:
    I need something with good compositional/midi tools, but I also need powerful audio editing...non-destructive editing in the arrange window... I definitely need drum programming ability..
    Taking just the key points above, Logic will definitely fit the bill better. Logic seems to be a better compositional tool, although PT can also be used for that. Both do SOME non-destructive editing in the arrange windows. Protools has no drum editor at all.
    However, PT is still better at audio editing.
    It would depend on how much audio editing you plan on doing vs midi/composition.
    The above poster is certainly in the ballpark about the add-ons you have to buy with PT just to equal the tools that come with Logic. I would say you'll probably have to spend at least another $1000 on plugin instruments and utility tools (CD burning/mastering) above the cost of PTLE software. Assume you will need at least the Music Production Toolkit in addition to PTLE. You will also want Toast Titanium to burn CDs unless you get Logic w/Waveburner.
    The 003 will definitely not sound as good as the Apogee.
    I've used PTLE since 1999 and it's great for recording and editing audio, but nothing special for writing and nothing special for midi.

  • Logic Crashing on startup!! Please Help!!

    I have just installed Logic 9 on my intel mac. I have a digi 003 interface. When I go to start, Logic crashes and reports that it's a DIGIDESIGN CORE AUDIO problem. This is NOT the melodyne/rewire issue. I don't have Melodyne at all. This is something else. Would love some thoughts. It's a thread 15 crash. PLEASE HELP!!!

    When I go to start, Logic crashes and reports that it's a DIGIDESIGN CORE AUDIO problem.
    I wonder if you have this file on your machine:
    Macintosh HD/Library/Audio/Plug-Ins/HAL/Digidesign CoreAudio.plugin
    If you move it to the desktop, does Logic still crash?

Maybe you are looking for