Time out condition for FTP parameters in communication channel

Hi
Could you please tell what should be the maximum limit for time out condition in receiver file communication channel for FTP.
it should be either 120,90 or 60 seconds or can we exceed time than this?
Thanks in advance
Best Regards,
Harleen Kaur Chadha

There is no hard limit, but the time limit should be less than the polling interval: if you set the polling interval to 60 seconds, your timeout interval should be less than that value. If you exceed this value, you have the risk of an adapter deadlock (adapter stops polling)
You can imagine that a timeout interval of 300 seconds would not make much sense.

Similar Messages

  • Time out period for PO approvals in worklist

    Hi all,
    Can any one know how to check the time out period for PO approvals in worklist other thant workflow builder like from system adminstrator or a query etc.,
    Thanks in advance,
    Regards,
    Pramod

    Hi,
    The following note might solve your problem :
    1330433.
    Thanks and Regards,
    Vignesh Ravikumar

  • Passing parameters from Communication channel to EJB Module

    Dear friends,
    We have an EJB module in NWDS. We want to pass some parameters from Communication Channel (Sender) in Integration Directory and use them in our EJB Module. Is there any function to do this process?? Please help me out
    Thanks and Regards,
    N.Jayanth Kumar

    Hi,
    Use the Channel object in this manner:
    String cid  = moduleContext.getChannelID();
    channel = (Channel) LookupManager.getInstance().getCPAObject(CPAObjectType.CHANNEL, cid);
    //To access channel parameters e.g in file adapter the connection parameters like host use the below code
    String host = channel.getValueAsString("ftp.host");
    PS: it is assumed that you are having the source code for adapter module development found on server
    Regards,
    Fariha

  • RFC Look Up APIs for a IDOC Receiver Communication Channel

    Hi,
    Can we use RFC Look Up APIs in UDF for a IDOC Receiver Communication Channel. (File to IDOC Scenario). Requirement is to send a notificaiton when IDOC got posted with IDOC number.
    Best Regards,
    Madan Agrawal

    As the name suggests, RFC lookup uses RFC receiver channel only. In mapping of your File to Idoc scenario, you may perform this lookup.
    Requirement is to send a notificaiton when IDOC got posted with IDOC number.
    Configure ALEAudit for this requirement. How were you planning to use RFC lookup for such a requirement?
    Regards,
    Prateek

  • Error time out to connect FTP server

    Hi Experts,
    I am getting the error in receiver communication channel (FTP) as :
    An error occurred while connecting to the FTP server ''. The FTP server returned the following error message: 'com.sap.aii.adapter.file.ftp.FTPEx: The control connection to the FTP server ""  timed out while reading the server reply.'. For details, contact your FTP server vendor.
    Getting this error for a particular interface. Changed the time out parameter but not working.
    the same IP address is used for same receiver but different interface and it is in green status.
    tried to restart the adapter but same time out error.
    Same configuation is done for two receiver channels .. but getting above error for a particular interface.Please help.
    Thanks,
    Swapnashree

    Hi Swapna,
        If you are facing problem with only one interface then you make some dummy changes in configuration(ID) to that perticular channel and activate.
    After doing this you just restart your communication channel and check if you have any luck.....
    Also check if you have permissions ......for the user and folder which you are accing in your channel...
    Naveen.

  • Time out issue for many users

    Hello all
    many users reported us TIMEOUT issue in our system
    we wanted to extract the report how many users were faced the same issue and why they have received  400 Session time out error.
    what parameter needs to be adjusted in SRM to avoid the same problem
    any help is appreciated and piece of information on this help .
    Muthu

    Hi Muthuraman,
    The error you are experiencing is caused by the icm/conn_timeout parameter being exceeded. You should increase this parameter to solve your issue. Also there are a number of other parameters that will cause the webdispatcher and ICM to close a connection.
    Please refer to SAP Note [824554|http://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes/sdn_oss_bc_cst/~form/handler%7b5f4150503d3030323030363832353030303030303031393732265f4556454e543d444953504c4159265f4e4e554d3d383234353534%7d] for additional information in webdispatcher and ICM timeouts.
    Michael

  • Time out problem for select query

    I am fetching data from BKPF for my report.
    I have written following query.But this query always time out.
    SELECT
        BUKRS
        BELNR
        GJAHR
        BLART
        BLDAT
        BUDAT
        MONAT
        XBLNR
        BKTXT
        WAERS
        KURSF
        HWAER
        FROM BKPF
        INTO TABLE I_BKPF
        WHERE BUKRS IN S_BUKRS
         AND BELNR IN S_BELNR
         AND GJAHR IN S_GJAHR
         AND BLART IN S_BLART
         AND BLDAT IN S_BLDAT
         AND BUDAT IN S_BUDAT
         AND MONAT IN S_MONAT
         AND CPUDT IN S_CPUDT
         AND BSTAT = SPACE.
    So please suggest me solution.

    Hi..
    1) Try to make Some of the Fields such as BUKRS , GJAHR  as PARAMETERS so that ROWS are restrited mostly.
    2) Make fields like BLDAT and BUDAT as OBLIGATORY if possible.
    3) And in the SELECT query add the PACKAGE SIZE addition.
    <b>Reward if Helpful.</b>

  • Time stamp is not getting updated for File Adapter in communication channel

    Hi All,
    Since yesterday, I am observing that the time stamp of communication channel for File adapter is not gettingupdated some times.
    I had to stop and start the communication channel to update the time stamp.Please let me know if anyone has come across such issue or any useful notes on this.I could not find any related notes on Market place.
    Regards,
    Dinakar

    Hi,
    This is happening only with one communication channel which is sender in derection.Any reason why it is happening like this?since the restart of the communication channel it is getting update now.I really do not know how to delete/create the communication channels as this was done our PI consultants.Pls guide me.
    Regards,
    Dinakar

  • BAPI_SAG_CREATE - time indepenedent condition  for schdule line agreement

    Hi all,
    i have nade a BAPI -BAPI_SAG_CREATE for schedule line agreement. it is running okay for time dependent condition.
    but it is giving error " schedule line fortime independent condition is not asllowed"when i am running for the same bapi for time independent condition whereas it is our requiirement.
    kindly help.
    Regards,
    Santosh

    Hello Santosh,
    I think you have no chance, this time you found a missing funcionality, BAPI_SAG_CHANGE (and BAPI_SAG_CREATE) can only treat scheduling  agreements with time-dependent conditions. Document conditions are not  supported. Therefore, this kind of scheduling agreements cannot be           
    processed and you receive error message MEOUT019.   
    Regards,
    Mauro

  • Is there any time out defined for long running transaction?

    hi, 
    i have to make one big data transferring script , though transaction is not required here, but i was planning to,
    please tel me is there any time out for long running transactions.i have to run the script from database it self
    yours sincerley

    Can you show us an example of your script? You can divide the transaction into small chunks to reduce time and locking/blocking as well.
    Best Regards,Uri Dimant SQL Server MVP,
    http://sqlblog.com/blogs/uri_dimant/
    MS SQL optimization: MS SQL Development and Optimization
    MS SQL Consulting:
    Large scale of database and data cleansing
    Remote DBA Services:
    Improves MS SQL Database Performance
    SQL Server Integration Services:
    Business Intelligence

  • Session Time Out capturing for legacy application running in portal

    Hi Forums,
    I am using portal URL  iView to connect to legacy application. How to capture the session time of of that legacy application and show it in the portal. In portal I have already handled session time out which shows a javascript popup message. I want to call the same piece of code once session time out happens in the legacy application which is been accessed by portal through URL iview.
    Many Thanks and Best Regards
    Sudhir

    Hi Sudhir,
    The handling of the session timeout should be done by the application itself not the portal. From the portal you have no way of working out what the application is doing. My suggestion to you is that you need to modify the application to handle the scenario you describe not the portal.
    BRgds,
    Simon

  • Need to increase the Time out  parameter for executing BI queries

    Folks,
    We are publishing BI Query on portal , we are getting Time out error while executing the quries , please let me know how to increment the time out parameter
    Thanks
    Manish

    Hi Manish,
    Try this link
    Time out time
    Cheers....

  • [solved] systemd times out waiting for dev-null.device on encrypted fs

    I have a relatively new install of Arch on my laptop. The relevant sections of the drive setup are a luks encrypted root device (with associated unencrypted /boot), and a large ntfs device encrypted with truecrypt. That contains my home directory, which is shared with the Windows 8 dual-boot on the machine.
    I have all this mounted on boot, so my typical usage is to enter my password for the encrypted root, followed by the password for the truecrypt-encrypted data drive, then normal login.
    This has been working fine for a couple of weeks. This afternoon I rebooted my machine from Windows to Linux, at which point the secondary encrypted drive failed to mount. The root device mounts fine.
    On further examination, in the form of journalctl -xb, I'm getting the following errors after mounting the encrypted root device:
    Feb 12 21:29:54 kafka systemd[1]: Job dev-null.device/start timed out.
    Feb 12 21:29:54 kafka systemd[1]: Timed out waiting for device dev-null.device.
    -- Subject: Unit dev-null.device has failed
    -- Defined-By: systemd
    -- Support: http://lists.freedesktop.org/mailman/li … temd-devel
    -- Documentation: http://www.freedesktop.org/wiki/Softwar … e9d022f03d
    -- Unit dev-null.device has failed.
    -- The result is timeout.
    Feb 12 21:29:54 kafka systemd[1]: Dependency failed for Cryptography Setup for cryptdata.
    -- Subject: Unit [email protected] has failed
    -- Defined-By: systemd
    -- Support: http://lists.freedesktop.org/mailman/li … temd-devel
    -- Documentation: http://www.freedesktop.org/wiki/Softwar … e9d022f03d
    -- Unit [email protected] has failed.
    As my root home directory is on the root filesystem, I can still log in as root. If I try to mount or unmount the truecrypt device (located at /data) the command hangs. After removing "auto,x-systemd.automount" from that device from /etc/fstab and rebooting, I have a significant delay at boot, but I can then mount the /data device as normal.
    I can't find anything related to this either here or on Google. Any ideas?
    Last edited by tealeaf (2014-02-13 12:01:55)

    WonderWoofy wrote:A bit OT, but I just want to mention that having your $HOME on ntfs is probably not the best idea either.  It may work, but because it is not a POSIX compliant filesystem, there is a good chance you might run into some issues.
    Thanks for the warning. Sadly, as there are applications I need for work that only run in Windows, I need to dual boot this machine with Windows 8.1. This is the best option I can find for sharing my home directory, which is also a necessity due to the amount of data I have to share between the systems. I would much rather trust to ntfs-3g-ar and its UserMapping (and all the fiddling with ACLs that I had to do) than to the Windows ext2 drivers I can find. They all seem to be several years out of date. Linux is much better at talking NTFS than Windows is at talking EXT. (To be honest, I'm actually quite impressed with Windows 8 since the upgrade to 8.1. As a long term Arch user and a fan of tiling window managers it's interesting to see Windows moving in the right direction. )
    With 'permissions' in the /etc/fstab and the .NTFS-3G/UserMapping file in place it works almost seamlessly. (It took a lot of tinkering with ACLs in Windows and Linux, but it's working very well now. One tip that I'll write here in case it's of use is that you want the last line of the UserMapping file to be a 'generic' mapping. When I didn't have that there were very strange things going on.)
    The only two minor problems I have now are:
    1) A few applications don't like FUSE filesystems. Steam worked for a while and then broke; reinstalling it failed at every stage. When I checked, it seems that FUSE is a known problem for Steam. (I don't think it's restricted to NTFS.) My response to that was to create /home/.local/$HOME on my root (ext4) filesystem and symlink out to it for troublesome applications.
    2) There are a few characters for filenames that Windows doesn't like, making those files inaccessible in Windows. (Colons are the major culprit.) They're usually quite easily renamed. (The exception being my .maildir folder, which I have had to duplicate natively in cygwin.)
    Neither of these are anything more than minor niggles. I appreciate the warning, though.
    Having said that, if you have an alternative that lets me share a truecrypt-encrypted drive between Linux and Windows that is better than the NTFS-3G approach, I'd love to hear it for future reference.

  • Systemd Boot Problem - Times out waiting for LVM partitions

    At first I had a problem in which the initramfs didn't map LVM partitions to /dev/vg0/lv, only /dev/mapper/vg0-lv. I changed /dev/vg0/root to /dev/mapper/vg0-root in bootloader configuration as a hacky workaround.
    Getting closer to a working system, systemd failed boot because my fstab entries are uuids, and for some reason, my LVM volumes aren't showing up in /dev/disk/by-*. My flash drive boot partition shows up in there though.
    I replaced the uuids with /dev/mapper/vg0-* and tried again. Now my boot fails with this:
    Oct 21 19:19:31 archserver systemd[1]: Job dev-mapper-vg0\x2dmedia.device/start timed out.
    Oct 21 19:19:31 archserver systemd[1]: Timed out waiting for device dev-mapper-vg0\x2dmedia.device.
    Oct 21 19:19:31 archserver systemd[1]: Dependency failed for /mnt/media.
    Oct 21 19:19:31 archserver systemd[1]: Dependency failed for Local File Systems.
    Boot log: http://sprunge.us/LEhG
    mkinitcpio.conf: http://sprunge.us/QEBK
    What should I do?

    This may be LVM's incompatibility with anything hotplug (it may not be, your issue sounds more obscure). You need to create your own, local lvm service file. I'll tell you how. This is /usr/lib/systemd/system/lvm.service:
    [Unit]
    Description=LVM activation
    DefaultDependencies=no
    Requires=systemd-udev-settle.service
    After=systemd-udev-settle.service
    Before=basic.target shutdown.target
    Conflicts=shutdown.target
    [Service]
    ExecStart=/sbin/vgchange --available y
    Type=oneshot
    TimeoutSec=0
    RemainAfterExit=yes
    [Install]
    WantedBy=basic.target
    Create /etc/systemd/system/lvm_local.service:
    [Unit]
    Description=LVM activation
    DefaultDependencies=no
    Requires=dev-something-something1.device
    After=dev-something-something1.device
    Requires=dev-something-something2.device
    After=dev-something-something2.device
    Before=basic.target shutdown.target
    Conflicts=shutdown.target
    [Service]
    ExecStart=/sbin/vgchange --available y
    Type=oneshot
    TimeoutSec=0
    RemainAfterExit=yes
    [Install]
    WantedBy=basic.target
    No, what to you put in those "something-something1" places above? For each LVM physical volume, run 'systemctl status /dev/disk/by-uuid/$UUID' where $UUID is the UUID of your physical volume. You'll get a status output showing the exact name of the correct .device unit. Then 'systemctl enable lvm_local.service'.
    This speeds up boot and makes sure lvm is properly initialized. After writing all this, I am unsure if this is at all related to your problem, as your volume group is activated in initramfs and the links should be set up by udev.

  • Setting a time out limit for OBIEE Queries

    Hi Experts,
    I am using OBIEE 11g. I have a scenario where I have to cancell a query if the query runs for more than 15 mins to fetch the data. The requirement is if the query takes longer than 15 mins the query to the database should be cancelled and in the OBIEE answers it should show the query cancelled message. Even if we are not able to show the exact message in answers is fine. But the front end and backend query must be cancelled after running for 15 mins.
    Any help on this would be highly appreciated. Thanks in Advance.
    Satyabrat

    Hi,
    Please try the following:
    Add the below code in instanceconfig.xml
    To set time to expire for Idle Oracle BI Presentation services Client connections.
    <ConnectionExpireMinutes>Number of Minutes</ConnectionExpireMinutes>
    Setting the Time to Expire for Oracle BI Presentation Services Client Sessions
    <ClientSessionExpireMinutes>Number of Minutes</ClientSessionExpireMinutes>
    And also try in RPD
    Go to Manage-->Identity-->Application Roles
    Select the ROLE and click on the permissions tab.
    In the next wizard go to the “Query limits” tab.
    Against the database row set the following values
    Max Time Minutes=20
    Status Max Time=Enable
    For Custom messages for the error message:
    Find error webmessage template and rewrite it in customMessages. For example:
    <WebMessage name="kmsgCatalogAccessDenied" exception="true">
    <TEXT>Отказ в доступе на <sawm:param insert="2"/> пользователю <sawm:param insert="3"/> по пути <sawm:param insert="1"/>.</TEXT>
    </WebMessage>
    Found this in catalogmessages.xml. Then I created file custommessages.xml in msgdb\customMessages:
    <?xml version="1.0" encoding="utf-8" ?>
    <WebMessageTables xmlns:sawm="com.siebel.analytics.web/message/v1">
    <WebMessageTable system="CustomMessages">
    <WebMessage name="kmsgCatalogAccessDenied" exception="true"><TEXT>Some other error message</TEXT></WebMessage>
    </WebMessageTable>
    </WebMessageTables>
    It's possible not to show error message code.
    There are a lot of perfect examples in the documentation.
    Also Please refer the below link:
    http://sranka.wordpress.com/2008/05/23/style-sheet-changes-custom-look-and-feel-in-obiee/
    This should resolve your problem
    Regards
    MuRam

Maybe you are looking for