Unable to forward ports on HH4

Hi all,
Had Infinity 2 installed a couple of weeks ago, and I am finding it impossible to forward ports on the HH4. I have tried every which way but with no luck so, to make things easier to explain, have just factory reset my router and have done the following:
(The PC I am trying to forward to has the static IP of 192.168.0.10, and the port I need to forward is 4040)
Changed hub IP to 192.168.0.1 (my network is set up for this IP, have also tried on original IP with no success)
Changed DHCP range to 192.168.0.64 - 192.168.0.253
Disabled uPNP
Set up a new application 'Subsonic' to forward both protocols in the range 4040-4040, to translate to 4040-4040
Assigned this application to device of static IP 192.168.0.10
Apply settings.
... And nothing! Port still closed. Have I missed anything?
This is a major issue for me at the moment, somebody please help!
(Oops, forgot to add - Firewall and antivirus are both off on the PC)

Tried 192.168.0.58, 192.168.0.60 and 192.168.0.200 (after adjusting the DHCP assign to 192.168.0.66-192.168.0.100)
No luck on any of them - Just get this as usual....

Similar Messages

WRT54GS v6 Unable to do Port Forwarding

Yesterday, I downloaded the latest firmware for my router since I had been having some odd issues.... Anyways, I need to forward ports for gaming and such, and now I am totally unable to.
When I put in the ports, which gave me no problems in the past, I consistently receive the error message: "Port Overlap Occurred! Please change your Entry!"
I tried this from another machine on the network with a different operating system and received the same message. I am not sure what is going on? Is this anything to do with the firmware?

well in this case you need to reset the router back to factory default settings, try following steps... try reflashing/upgrading firmware for the router, after upgrading firmware on the router, reset the router back to facotry default settings and reconfigure it according to ISP settings, assign a statis IP on computer, e.g. 192.168.1.10 Subnet Mask 255.255.255.0 Default Gateway to 192.168.1.1 Primary DNS 192.168.1.1 Secondary DNS 4.2.2.2... logon to router's setup page, enable UPnP, reduce MTU to 1365 and try forwarding ports again and let me know if it works or not...

WRT54GS Ver 3 wont forward ports.

My WRT54GS won't forward ports after a reformat. I have done proper port forwarding before and followed the same process of forwarding a port. I also set a static IP to be sure I am opening the right IP. Using the Utorrent checker (http://www.utorrent.com/testport?port=6881) and www.canyouseeme.org i am unable to see any ports. But when I run Utorrent, it magically opens the port its using without issue. I do not know what the issue is and any help would be vastly appreciated.

The status page looks like this:
Firmware Version: v4.71.4, Oct. 31, 2007
Current Time: Thu, 29 Oct 2009 10:39:59
MAC Address: 00:1D:60:26:22:C5
Router Name: WRT54GS
Host Name:
Domain Name: ri.cox.net
Configuration Type
Login Type: Automatic Configuration - DHCP
IP Address: 68.229.64.48
Subnet Mask: 255.255.252.0
Default Gateway: 68.229.64.1
DNS 1: 68.105.28.12
DNS 2: 68.105.29.12
DNS 3: 68.105.28.11
MTU: 1500
Port forwarding tab:
http://img177.imageshack.us/i/prf.png/
Ports are kinda all over the place because I was trying a lot of stuff to fix it.
Ipconfig /all:
http://img526.imageshack.us/i/ipconfig.jpg/
The tunggle adapter is for a VPN which I installed after the problem existed
netstat-an:
http://tinypic.com/view.php?pic=14t1q52&s=4
http://tinypic.com/view.php?pic=2yweu5d&s=4
http://tinypic.com/view.php?pic=24planp&s=4
I hope this helps!

I've been having a problem forwarding ports in my router...

I've been having a problem forwarding ports in my router WRT160N I enable the ports I want to use for my applications, just after clicking save settings I go back to my port's forwarding section and I don't see any application I add being saved. Please help, thanks.
Message Edited by AudioSoft on 04-09-2008 05:31 PM

Might be possible that it will take time to save the settings ... so once you click save settings wait for few seconds ...
Also if it not working ... disable all firewall on the computer & then try to configure the router ...

Linksys keep prompting for username and password when trying to forward port

As when we want to access the linksys router homepage we enter 192.168.1.1, and than we enter our user name and password. This is a normal step. But lately when i wanna forward a port and change the last 3 digit of the ip address, eg. to 101, i keep getting a promt for my user name and password but when i enter it correctly, it sill prompt me no matter whats. I used to forward port with no problem but do not know why this problem started to arise. Can anyone help me with this?
Btw i am using Linksys B router. THANKS

were u using the default password ?? because there is a possibility that someone in your neighbourhood must have connected to the wireless network and changed the router login password..
apart from this i don't see any reason of the old router password not working ..

I am unable to forward message in ios8

I am unable to forward message in ios8. After updating an iPhone 5s to ios8 I am
unable to forward messages. Selecting the more button does not bring up the bottom menu. Any ideas?

If you have really done that, then the next step is unfortunately a restore:
Back up and restore your iOS device with iCloud or iTunes
Use iTunes to restore your iOS device to factory settings
If you can't update or restore your iPhone, iPad, or iPod touch

How do I forward ports on my Airport Express?

I've been trying to get my ports open for a while now, but haven't succeeded. Here's my setup:
I have an Airport Express connected to a Dynalink RTA1320 ADSL2+ modem. I am running 10.5.2.
On the Dynalink modem, I have set 10.0.1.1 as a DMZ host, which is the address of the Airport Express.
I understand that in Airport Utility, I need to set private and public ports, as well as IP address. I am using NPMP with the Airport Express, and I have a default host set as 10.0.1.253. This is the IP address I am using on my Mac, and the one that I am using when forwarding ports on the Airport Express.
Even after doing all this, online port checkers still say that the ports I have forwarded are closed, and I can't work out why.
However: I am using XTorrent as my BitTorrent client. I have the port 49350 set as the default port in that application. XTorrent has the ability to open ports by itself, and it seems to have succeeded at doing this, even though I cannot open other ports manually. 49350 reads as open when using an online port checker.
These are the questions I have:
1. Am I inputting the right IP addresses?
2. Is NPMP doing me any good, or should I be using straight DHCP?
3. Am I doing the right thing by setting 10.0.1.1 as a DMZ?
4. Am I doing anything else wrong?
Thanks very much for your input in advance.

On the Dynalink modem, I have set 10.0.1.1 as a DMZ host, which is the address of the Airport Express.
This is probably incorrect. 10.0.1.1 is the LAN IP address of the AirPort Express (AX). You want to use the IP address provided by the Dynalink to the AX. It is the IP address used on the WAN side of the AX.
...Airport Express, and I have a default host set as 10.0.1.253.
If you configure the AX for Default Host operation, ALL of the ports are forwarded to the assigned IP address. The is no other configuration needed to forward the ports.

Want to forward ports, but 'add' and 'default host' are grayed out! help!

Hey folks. Configuring my laptop to access a new airport express plugged in one floor below me. great signal connection works fine, but of course it isn't forwarding ports i want... so I go to set it up... now, the owner of the house set it up first, but he told me the password so I could futz with it... now when i pull up the base station config in airport admin, the relevant options are grayed out! The whole section in which default host option is located is grayed out, as are all the buttons e.g. 'add' on the forward ports tab! I've tried doing all the tricks I can think of; if anyone has any insight as to where to look to fix this, I'd appreciate it enorm.
George

Copy these commands into TextEdit, replace the bracketed part with your username and the quoted parts with the ext HD's name, retaining the quotes.
sudo chflags 0 /Volumes/"name of ext HD"
sudo chmod a+rx /Volumes/"name of ext HD"
Launch the Terminal app in /Applications/Utilities, copy and paste the first one into the window that pops up, and hit the return key. When the Password: prompt pops up, carefully type in your admin password, since nothing shows on the screen, and hit the return key. Copy & paste the other two, one at a time, following each with hitting the return key. You won't get the password prompt, since the initial one's good for five minutes.
Quit the Terminal app and you should be able to read and write to the ext HD.

I am unable to forward my photos through iMessage here lately. I have iPhone5 and started having this problem within last month. Anyone have a solution I can try?

I have been unable to forward photos and videos within the last month on my iPHone 5. Anyone else having this problem and does anyone have a solution?

Hello,
I found the exact solution. It is very simple thank you. But I want to remove the passcode on my phone can anyone help me.
Thanks
Srini.

ERROR: NAT unable to reserve ports.

Hi guys,
I am trying to let the PPTP VPN traffic passing through a new Cisco ASA 5505 but I cannot NAT any UDP traffic using the outside interface as public ip for the incoming VPN connections.
The error arrears I run these commands:
object network CUSTOMER-VPN-SERVER-INTERNAL
nat (inside,outside) static interface service udp isakmp isakmp
I get the following error:
ERROR: NAT unable to reserve ports.
My version is:
Cisco Adaptive Security Appliance Software Version 8.4(2)18
Device Manager Version 6.4(5)
Here below my configuration (sanitized as much as I could). Can you please help me find out where I am mistaking?
ASA Version 8.4(2)18
hostname CUSTOMER-SITE1
domain-name CUSTOMER
names
name 192.168.31.0 CUSTOMER-SITE1
name 192.168.32.0 CUSTOMER-SITE2
name 192.168.32.253 CUSTOMER-SITE2-FW-LAN
name YYY.YYY.YYY.YYY CUSTOMER-SITE2-FW-WAN
name 192.168.31.253 CUSTOMER-SITE1-FW-LAN
name XXX.XXX.XXX.XXX CUSTOMER-SITE1-FW-WAN
name 192.168.31.2 USER-TEST-PC
name 192.168.31.30 CUSTOMER-SITE1-VPN-SERVER-PRIVATE
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Vlan1
nameif inside
security-level 100
ip address 192.168.30.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address CUSTOMER-SITE1-VPN-SERVER-PUBLIC 255.255.255.252
object network CUSTOMER-SITE1
subnet 192.168.31.0 255.255.255.0
object network CUSTOMER-SITE2
subnet 192.168.32.0 255.255.255.0
object network USER-TEST-PC
host 192.168.31.186
object network CUSTOMER-SITE1-VPN-SERVER-PUBLIC
host 116.212.244.138
description Created during name migration
object network CUSTOMER-SITE1-VPN-SERVER-INTERNAL
host 192.168.31.30
description VPN SERVER
object-group service DM_INLINE_SERVICE_1
service-object tcp destination eq pptp
service-object udp destination eq 4500
service-object udp destination eq isakmp
service-object gre
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object gre
access-list outside_1_cryptomap extended permit ip object CUSTOMER-SITE1 object CUSTOMER-SITE2
access-list inside_nat0_outbound extended permit ip object CUSTOMER-SITE1 object CUSTOMER-SITE2
access-list inside_access_in extended permit ip any any
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any object CUSTOMER-SITE1-VPN-SERVER-INTERNAL
access-list outside_access_in extended permit tcp any object USER-TEST-PC eq www
nat (inside,any) source static CUSTOMER-SITE1 CUSTOMER-SITE1 destination static CUSTOMER-SITE2 CUSTOMER-SITE2 no-proxy-arp
object network CUSTOMER-SITE1
nat (inside,outside) dynamic interface
object network USER-TEST-PC
nat (inside,outside) static interface service tcp www www
object network obj_any
nat (inside,outside) dynamic interface
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer CUSTOMER-SITE2-FW-WAN
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map interface outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
tunnel-group 116.212.199.226 type ipsec-l2l
tunnel-group 116.212.199.226 ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect pptp
Thanks,
Dario

(sanitized)
ASA Version 8.4(2)18
hostname xxxxxx
enable password xxxxxx
passwd xxxxxx
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address xxxxxx 255.255.255.224
boot system disk0:/asa842-18-k8.bin
ftp mode passive
clock timezone SGT 8
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server xxxxxx
name-server xxxxxx
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Public_Address
host xxxxxx
object network VPN-TCP
host 192.168.1.2
object network VPN-UDP
host 192.168.1.2
object network xxxxxx
host 192.168.1.2
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object gre
access-list outside_access_in extended permit ip any any
access-list outside_access_in_1 extended permit gre any host 192.168.1.2
access-list outside_access_in_1 remark VPN TCP Connection
access-list outside_access_in_1 extended permit tcp any object VPN-TCP eq pptp
access-list outside_access_in_1 remark VPN UDP Connection
access-list outside_access_in_1 extended permit udp any object VPN-UDP eq isakmp
access-list inside_access_in remark All inside to outside connections
pager lines 24
logging enable
logging asdm informational
logging mail alerts
mtu inside 1500
mtu outside 1500
ip verify reverse-path interface outside
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
asdm image disk0:/asdm-641.bin
no asdm history enable
arp timeout 14400
object network VPN-TCP
nat (inside,outside) static interface service tcp pptp pptp
object network VPN-UDP
nat (inside,outside) static interface service udp isakmp isakmp
object network Kaseya-TCP
nat (inside,outside) after-auto source dynamic any interface description Default NAT from Inside to Outside
access-group inside_access_in in interface inside
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 XXXXXX
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
http server enable 11443
http 0.0.0.0 0.0.0.0 outside
http 0.0.0.0 0.0.0.0 inside
http redirect inside 80
snmp-server host inside 192.168.1.2 community *****
snmp-server host inside 192.168.1.5 community *****
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec fragmentation after-encryption inside
crypto ipsec fragmentation after-encryption outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
XXXXXX
quit
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 inside
ssh XXXXXX 255.255.255.255 outside
ssh timeout 5
console timeout 0
management-access inside
dhcpd auto_config outside
dhcpd dns XXXXXX XXXXXX interface inside
threat-detection basic-threat
threat-detection scanning-threat shun except ip-address 192.168.1.0 255.255.255.0
threat-detection scanning-threat shun duration 3600
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
ntp server 118.107.60.254 source outside
ntp server 121.0.0.41 source outside
ntp server 202.60.94.11 source outside prefer
webvpn
port 11443
enable outside
group-policy DfltGrpPolicy attributes
webvpn
url-list value Administration
group-policy GroupPolicy1 internal
group-policy GroupPolicy1 attributes
vpn-tunnel-protocol ikev1 ikev2
username XXXX password XXXXXX encrypted privilege 15
vpn-group-policy DfltGrpPolicy
tunnel-group ClientlessVPN type remote-access
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect ctiqbe
inspect dcerpc
inspect icmp
inspect icmp error
inspect ils
inspect ipsec-pass-thru
inspect mgcp
inspect snmp
inspect waas
inspect pptp
service-policy global_policy global
prompt hostname context
call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:af0d8ba03c99dd37540a4d0a4bf569d2
: end

Forward Ports

I have a Linksys EA6900 Router.
I'm setting up a security system with IP cameras and need 4 ports opened.
I'm trying to forward ports. I had to open port 80 for my crameras, I entered the information in the single port fordwarding section and it opened fine. I entered port 8200 with the same iP address I used for port 80 but won't open. But I can change the Ip address for port 8200 then it opens.
I opened 3 ports with the same IP address I used to open port 80 in port range forwarding and it worked.
My question is because I'm using IP cameras should I use the IP address of the each camera or the DVR for the cameras or the router?
Thanks for the help

I looked up what you gave me but there just isn't any useful information regarding the system.
The IP Camera must be streaming video to the NVR so it has something to record.
Check to see if the NVR has a website or remote access you can use on your local network. Then use port forwarding to make those services of the NVR available to you off site.
Another option would be to use different external ports to each IP Camera.
Ex:
Camera 1 Port Forward rule:
External Port 10001 to internal Camera 1 IP Address port 80
Camera 2 Port Forward rule:
External Port 10002 to internal Camera 2 IP Address port 80
Etc................
To remote access Camera 1:
http://your-public-ip:10001
To remote access Camera 2:
http://your-public-ip:100012
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Issue Forwarding Port 7000 on RVS4000 Router

Hi Everyone,
I have recently replaced a WatchGuard Firebox SOHO 6 with a Linksys 4 Port Router Mod: RVS4000 because the WatchGuard was becoming unstable.
I set up the new router with all the settings from the previous equipment, which included forwarding port 7000 to a specific IP.
This port broadcasts images from a surveillance software installed on a computer with a static IP (the computer runs on Vista).
In order to view the broadcasted video on another computer, I use a proprietary software not a web browser.
So far, I tried single port forwarding without being able to view the images and range port forwarding with the same result.
I spend over an hour with the Business Tech Support from Linksys without success. They even remoted into the device and found nothing suspicious.
Currently the router runs on firmware version 1.2.11 and the Tech Support people suggested upgrading to a newer version.
I'm concerned to do so because I in read other postings that I can run into a bigger problem (i.e. bricking the router).
Finally, other ports are being forwarded (i.e. port 3389 RDP) and it works fine, so at least I know the forwarding feature is working properly.
Can someone shed some ligh as to what to do next?
Needless to say, everything was working fine with the WatchGuard Firebox and no changes in equipment, IPs or other software/hardware have been done.
Thank you in advance fro your help.
danielk

Greetings,
That sounds peculiar that some ports would get forwarded but others not, you might want to check and see if your ISP is blocking the ports if your going through the internet to this security application. If everything is local, then you should try to follow the advice of upgrading your firmware to the latest version, in order to avoid "bricking" your router do the following sequence, before you upgrade:
do a backup of your configuration (optional)
Reset router to factory default settings from the GUI.
Upgrade to latest firmware.
Reset router to factory default settings again from the GUI.
Configure everything again manually *RECOMENDED*
This somewhat ilogical sequence of events prevents the IOS from being corrupted and has worked in many cases I have dealt with regarding router "lock up" issues.
Besides that the only thing else I can think of is find out if there are any more additional ports required for this application to work properly and check to see if your using the exact protocol UDP or TCP for the ports that are being forwarded.
Regards.

E90 unable to forward text messages after software...

Hi,
I recently updated my e90 to 300.34.84 software and now I am unable to forward text messages. You can only forward by manually typing in the numbers. If you choose via the "add recipient" option, it brings you to your contacts list and you can mark "x" on the box beside the name however there is no "ok" option, just a "back" option which if chosen, brings you back to the text message you want to forward without any name on the top. Any help on how to solve this is much appreciated

try doing the following on the senders iPhone : http://ios.wonderhowto.com/how-to/fix-delayed-imessages-text-messages-after-upgr ading-ios-7-0148663/
then see if you can receive SMS from him.

How to forward ports using Airport Extreme?

So,
I wanna forward some ports but every guide I find on the internet describes how to use the Airport Admin Utilty to do this. The problem is though that I can't configure my AE using AIrport Admin Utility; I need to use my Airport Utility instead. The only problem is that I don't know how to forward ports using Airport Utility.
Anyone?

In AirPort Utility, Port Forwarding is called Port Mapping which is under the Advanced->Port Mapping tab.

How to forward port 25565?

I'm trying to run a minecraft server, and whenever I try to forward my port in port mapping in network preferences, I still get a "port 25565 is closed" on a port checking website. Putting my ip in the interenet browser does not load any setting either

Evan21437 wrote:
The main router is my 1 generation connected to my Ethernet/modem
So this TC gets the public IP address? Please check the summary page of the TC that it has a public not private wan IP.
The extend network TC is bridged so that doesn't matter. The only place you forward ports is the main TC if it is the main router of the network.
Post the screen shots of the setup of port forwarding on that.

Unable to forward ports on HH4

Similar Messages

Maybe you are looking for