Unable to get tunnel configured

I have a 2911 that has a few existing IPSec tunnels and I'm looking to add one in except the encryptio is a little different. I will be using AES vs DES like the other transform sets. - This what I have configured except I still don't see the tunnel when I do sh crypto isakmp sa... What could I be doing wrong?
note: I also added the peer address to access-list 101, do I need to allow it through outgoing_to_source?
Configure ISKAMP Policy
crypto isakmp policy 3
   encr aes 256
   authentication pre-share
hash sha
lifetime 86400
   group 2
Configure IPsec Transform Set
  crypto ipsec transform-set ESP-AES-SHA esp-aes 256 esp-sha-hmac
Specifies the interesting traffic to be encrypted
ip access-list extended outgoing_to_source
permit ip 192.168.18.0 0.0.0.255 host 10.1.1.198
permit ip 192.168.18.0 0.0.0.255 host 10.1.1.197
permit ip 192.168.18.0 0.0.0.255 host 10.1.1.226
permit ip 192.168.18.0 0.0.0.255 host 10.1.10.20
permit ip 192.168.18.0 0.0.0.255 host 10.1.10.21
permit ip 192.168.18.0 0.0.0.255 host 10.1.10.22
permit ip 192.168.18.0 0.0.0.255 host 10.1.10.24
permit ip 192.168.18.0 0.0.0.255 host 10.1.10.121
permit ip 192.168.18.0 0.0.0.255 host 10.1.10.122
Specifies the pre-shared key "secretkey" which should be identical at both peers
crypto isakmp key "secret-key" address 65.x.x.x no-xauth
Configure the Ipsec-isakmp
crypto map vpn-map 1 ipsec-isakmp
set peer 66.x.x.x
set transform-set ESP-AES-SHA
match address outgoing_to_source
Apply the Ipsec-isakmp to interface
interface GigabitEthernet0/1
description ** Connection to internet **
ip address 174.x.x.x 255.255.255.248
ip access-group 101 in
ip access-group 131 out
ip flow ingress
ip nat outside
ip inspect standard in
ip virtual-reassembly
duplex auto
speed auto
crypto map vpn-map

I do not believe so, and might be green to what you are asking. Would I need to create a deny ACL in order to prevent the NAT process?
These are the remote hosts I'm trying to reach -
Remote Hosts: 10.1.1.198
10.1.1.197
10.1.1.226
10.1.10.20
10.1.10.21
10.1.10.22
10.1.10.24
10.1.10.121
10.1.10.122
Security Profile: ESP-AES-256-SHA
                                Group 2
                                SHA
                                86400 Lifetime

Similar Messages

IFS-20010 Unable to get service configuration

Hi,
I'm trying to connect to iFS from a Java application. Basically it's a remote server which we'll connect to using RMI for some integration work. It will run on the same server as CM SDK.
Anyway, I try and connect to the service using:
LibraryService.startService(name, schemaPassword, serviceConfig, domainName)
and it comes back with this error:
oracle.ifs.common.IfsException: IFS-20102: Unable to start service (IfsDefault)
oracle.ifs.common.IfsException: IFS-20010: Unable to get service configuration properties (SmallServiceConfiguration)
java.lang.NullPointerException
at oracle.gss.util.NLSLocale.getNLSLanguage(NLSLocale.java:675)
I'm running it from the command line, I have a batch file to set the classpath. Interestingly, if I run an Agent (i.e., a java class that extends oracle.ifs.management.domain.IfsServer) standalone, it works fine.
This makes me think there's some element of the classpath that I'm missing, but I'm not entirely sure what!
Could anyone shed any light on this? Metalink doesn't seem to have anything!
Cheers,
Phill
P.S. -- my CLASSPATH is as follows:
set CLASSPATH=%CLASSPATH%;%ORACLE_HOME%\ifs\cmsdk\lib\cmsdk.jar;%ORACLE_HOME%\lib;
set CLASSPATH=%CLASSPATH%;%ORACLE_HOME%\jdbc\lib\classes12.zip;%ORACLE_HOME%\j2ee\home\lib;
set CLASSPATH=%CLASSPATH%;%ORACLE_HOME%\j2ee\home\jazn.jar
set CLASSPATH=%CLASSPATH%;%ORACLE_HOME%\jdbc\lib\nls_charset12.jar
set CLASSPATH=%CLASSPATH%;%ORACLE_HOME%\ifs\cmsdk\settings\

Just FYI, the solution to this was that the java security policy was denying access. I changed the java.policy to
grant {
permission java.security.AllPermission;
And this solved the problem.

IFS-20010 : Unable to get service configuration properties

Hi all,
I am trying to connect to IFS using JDeveloper. I have coded a JSP which makes a call to my java class to connect.
I know that I can connect from my machine because I can run a simple application from the command line to create
a file in IFS.
Anyway, I set up my classpath under Project Settings as follows (same as my classpath on command line):
C:\oracle\JDeveloper\9ifs\settings;.;C:\DOCUMENT\jars\adk.jar;C:\DOCUMENT\jars\email.jar;
C:\DOCUMENT\jars\repos.jar;C:\DOCUMENT\jars\utils.jar;C:\DOCUMENT\jars\xmlparserv2.jar;
C:\oracle\ora90\jdbc\lib\classes12.zip
When I run the jsp under JDeveloper I get the following output on my developer console.
Should the classpath value be what I have entered for my classpath under Project Settings?
Any help is appreciated,
Paul
C:\jdev9i_902\jdk\bin\javaw.exe -ojvm -classpath C:\jdev9i_902\j2ee\home\oc4j.jar com.evermind.server.OC4JServer -config C:\jdev9i_902\jdev\system\oc4j-config\server.xml
[Starting OC4J using the following ports: HTTP=9011, RMI=23916, JMS=9252.]
[waiting for the server to complete its initialization...]
Oracle9iAS (9.0.2.0.0) Containers for J2EE initialized
Target URL -- http://127.0.0.1:9011/maps-ifs-context-root/docScreens/test.jsp
oracle.ifs.common.IfsException: IFS-20102: Unable to start service (IfsDefault)
oracle.ifs.common.IfsException: IFS-20010: Unable to get service configuration properties (IfsDefault)
void oracle.ifs.common.IfsException.<init>(int, java.lang.Object[])
oracle.ifs.common.AttributeValue[] oracle.ifs.beans.LibraryService.getServiceConfigurationProperties(java.lang.String)
oracle.ifs.beans.LibraryService oracle.ifs.beans.LibraryService.startService(java.lang.String, java.lang.String)
oracle.ifs.beans.LibrarySession com.fujitsu.docHandler.dao.BusinessDocument_IFS_DAO.connect(java.lang.String, java.lang.String, java.lang.String, java.lang.String)
void com.fujitsu.docHandler.dao.BusinessDocument_IFS_DAO.<init>(java.lang.String, java.lang.String, java.lang.String, java.lang.String)
void docscreens.testForm._jspService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtime.HttpJsp.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void oracle.jsp.runtimev2.JspPageTable.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse, java.lang.String)
void oracle.jsp.runtimev2.JspServlet.internalService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtimev2.JspServlet.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void javax.servlet.http.HttpServlet.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.invoke(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.forwardInternal(javax.servlet.ServletRequest, javax.servlet.http.HttpServletResponse)
boolean com.evermind.server.http.HttpRequestHandler.processRequest(com.evermind.server.ApplicationServerThread, com.evermind.server.http.EvermindHttpServletRequest, com.evermind.server.http.EvermindHttpServletResponse, java.io.InputStream, java.io.OutputStream, boolean)
void com.evermind.server.http.HttpRequestHandler.run(java.lang.Thread)
void com.evermind.util.ThreadPoolThread.run()

Did anyone find a solution to the problem described in this thread?
I have made a simple stateless session bean in JDeveloper from which I try to connect to iFS. If I use the
embedded oc4j container in JDeveloper, I get the following exception:
Standard output of the EJB:
oracle.ifs.common.IfsException: IFS-20010: Unable to get service configuration properties (IfsDefault)Print stacktrace:
oracle.ifs.common.IfsException: IFS-20102: Unable to start service (IfsDefault)
oracle.ifs.common.IfsException: IFS-20010: Unable to get service configuration properties (IfsDefault)
     void oracle.ifs.common.IfsException.<init>(int, java.lang.Object[])
     oracle.ifs.common.AttributeValue[] oracle.ifs.beans.LibraryService.getServiceConfigurationProperties(java.lang.String)
     oracle.ifs.beans.LibraryService oracle.ifs.beans.LibraryService.startService(java.lang.String, java.lang.String)
     oracle.ifs.beans.LibrarySession xpackage1.impl.XSessionEJBBean.startSession(java.lang.String, java.lang.String)
     oracle.ifs.beans.LibrarySession XSessionEJB_StatelessSessionBeanWrapper0.startSession(java.lang.String, java.lang.String)
     java.lang.Object java.lang.reflect.Method.invoke(java.lang.Object, java.lang.Object[])
     void com.evermind.server.rmi.RMICallHandler.run(java.lang.Thread)
     void com.evermind.util.ThreadPoolThread.run()
The test client gets these messages:
oracle.ifs.common.IfsException: IFS-20102: Unable to start service (IfsDefault)
oracle.ifs.common.IfsException: IFS-20010: Unable to get service configuration properties (IfsDefault)
If I use oc4j in the application server, then I get the following exception:
Standard output of the EJB:
Localized message: IFS-20102: Message unavailableMessage: IFS-20102: Message una
vailableTo string :oracle.ifs.common.IfsException: IFS-20102: Message unavailabl
e
oracle.ifs.common.IfsException: IFS-20122: Message unavailable
oracle.ifs.common.IfsException: IFS-12000: Message unavailable
java.util.MissingResourceException: Can't find bundle for base name oracle.ifs.b
eans.resources.LibraryResources, locale no_NOPrint stacktrace:
oracle.ifs.common.IfsException: IFS-20102: Message unavailable
oracle.ifs.common.IfsException: IFS-20122: Message unavailable
oracle.ifs.common.IfsException: IFS-12000: Message unavailable
java.util.MissingResourceException: Can't find bundle for base name oracle.ifs.b
eans.resources.LibraryResources, locale no_NO
void java.util.ResourceBundle.throwMissingResourceException(java.lang.St
ring, java.util.Locale)
java.util.ResourceBundle java.util.ResourceBundle.getBundleImpl(java.lan
g.String, java.util.Locale, java.lang.ClassLoader)
java.util.ResourceBundle java.util.ResourceBundle.getBundle(java.lang.St
ring, java.util.Locale)
void oracle.ifs.common.Localizer.<init>(java.util.Locale, oracle.ifs.bea
ns.LibrarySession)
void oracle.ifs.common.Localizer.<init>(java.util.Locale)
void oracle.ifs.common.Localizer.<init>()
void oracle.ifs.server.S_LibraryService.<init>(java.lang.String, java.la
ng.String, oracle.ifs.common.AttributeValue[])
oracle.ifs.server.S_LibraryService oracle.ifs.server.S_LibraryService.st
artService(java.lang.String, java.lang.String, oracle.ifs.common.AttributeValue[
oracle.ifs.beans.LibraryService oracle.ifs.beans.LibraryService.startSer
vice(java.lang.String, java.lang.String, oracle.ifs.common.AttributeValue[])
oracle.ifs.beans.LibraryService oracle.ifs.beans.LibraryService.startSer
vice(java.lang.String, java.lang.String)
oracle.ifs.beans.LibrarySession xpackage1.impl.XSessionEJBBean.startSess
ion(java.lang.String, java.lang.String)
oracle.ifs.beans.LibrarySession XSessionEJB_StatelessSessionBeanWrapper0
.startSession(java.lang.String, java.lang.String)
java.lang.Object java.lang.reflect.Method.invoke(java.lang.Object, java.
lang.Object[])
void com.evermind.server.rmi.RMICallHandler.run(java.lang.Thread)
void com.evermind.util.ThreadPoolThread.run()
The test client gets theese messages:
oracle.ifs.common.IfsException: IFS-20102: Unable to start service (IfsDefault)
oracle.ifs.common.IfsException: IFS-20122: Unable to construct service
oracle.ifs.common.IfsException: IFS-12000: Unable to construct localizer
java.util.MissingResourceException: Can't find bundle for base name oracle.ifs.beans.resources.LibraryResources, locale no_NO
java.util.MissingResourceException: Can't find bundle for base name oracle.ifs.beans.resources.LibraryResources, locale no_NO
The classpath of the actual project in JDeveloper is:
C:\oracle\ora92ias\9ifs\settings;C:\oracle\ora92ias\9ifs\lib\adk.jar;C:\oracle\ora92ias\9ifs\lib\email.jar;C:\oracle\ora92ias\9ifs\lib\repos.jar;C:\oracle\ora92ias\9ifs\lib\utils.jar;C:\oracle\ora92\jdbc\lib\classes12.jar;C:\oracle\ora92ias\lib\xmlparserv2.jar;C:\oracle\ora92ias\j2ee\home\oc4j.jar;C:\oracle\ora92ias\j2ee\home\ejb.jar;C:\oracle\ora92ias\j2ee\home\jaas.jar;C:\oracle\ora92ias\j2ee\home\jaxp.jar;C:\oracle\ora92ias\j2ee\home\jdbc.jar;C:\oracle\ora92ias\9ifs\lib\http.jar;C:\oracle\ora92ias\9ifs\lib\provider.jar;C:\oracle\ora92ias\9ifs\lib\webui.jar;C:\oracle\ora92ias\jlib\javax-ssl-1_2.jar;C:\oracle\ora92ias\jlib\jssl-1_2.jar
Other information:
I have oracle 9i, application server and iFS installed on one machine with the windows advanced server 2000 os.
Does anyone know what I can do in order to solve this problem?
Thanks,
Anne Sommerhein

Unable to get package configuration option in .dtsx file.

Hi Team,
I am unable to get see the package configuraiton option on my package.
I have created SSIS project in VS Data Tool of SQL SERVER 2012.
Can you please, correct me with appropriate setting.

Hi Sandip,
Just an addition, you can refer to the following screenshot:
Regards,
Mike Yin
TechNet Community Support

Host: Unable to load application configuration + wrong install version on download

i am using 64 bit windows 7 ... when unable to playing video, it redirects me to the adobe download pages to get flash player ... the page says i am about to download flashplayer for win7 64 bit, of 9MB approximately, but the file i get has name "install_flashplayer11x32_mssd_aih.exe" (NOTE THE NUMBER 32) and this file just wont install it ends with error message: HOST: Unable to load application configuration ...
By google i found also file install_flashplayer11x64_mssd_aih.exe (NOTE THE NUMBER 64) ... this file runs the install, i get the final screen saying "installation completed" but after clicking the "finish" button i get an error message saying "an error occured while sending a command to the program" ...
I am just getting mad ... its 3 days i am trying to figure aout this problem ...
i also tryed files as "install_flash_player_11_plugin.exe" , "install_flash_player_11_plugin.msi" , "install_flash_player_11_active_x.exe" and "install_flash_player_11_active_x.msi" ... those files actually proceeds with the install, but at the end, the videos are still not displaying ...
When i am checking the plugins statuses in my firefox addons manager, it says Shockwave Flash is all right ...
The precedent version of flash player was working just fine, i do not understand why you must make such a mess every 2 months ...
How do i get work this?

yes, the pages is http://get.adobe.com/flashplayer/
the page says:
Adobe Flash Player 11.3.300.257 (9.36 MB)
Your system: Windows 64-bit , English, Firefox
but when i click the "Download now" button i get the file named "install_flashplayer11x32_mssd_aih.exe" (NOTE THE NUMBER 32) which wont start and after few seconds i get the message "HOST: Unable to load application configuration"
but finaly i solved the problem ... i just installed the file found by google on some private page "install_flashplayer11x64_mssd_aih.exe" (NOTE THE NUMBER 64)
(the page is here: http://www.ziddu.com/download/16693235/install_flashplayer11x64_mssd_aih.exe.html)
and after that i disabled the protected mode of flashplayer by adding a line in the cfg file
the howto is here: http://forums.adobe.com/thread/1018071
i must say its quite shameful one must get this torture to have movies playing on websites ... this cant happen at open source stuf, at least not for 3 days ...
and being already here and complaining, i must say also (i hope some adobe emploee will read this) i am quite disgusted (and i believe not only me) by adobes bad habit to provide other software than flashplayer, when they include mcafee antivir into the install ...
it is literally taking the user as a stupid one ...
if i will need an antivir, i will look for it ...
i just hate when some society tries to infiltrete in my comp some crap software counting on possibility that at the download i will not pay enough attention
its just ridiculous and shameful behavior

Unable to get 'InitialContext' using Java Client in Oracle App 10.0.2.0

Scenario & Problem Description: Unable to get 'Initial Context' using Simple Java Client in Oracle Application Server 10.0.2.0
I'm having an issue while I try to initialize the Initial Context for an EJB lookup from a simple Java Client [local lookup], but the same code snippet works fine when I try from Servlet. I have enclosed the Exception Stack Trace and the Code Snippet for your reference.
1. .NET Client ---> Servlet --> LookupUtility --> EJB --> DB - Issue
2. .NET Client ---> Servlet --> EJB --> DB - Works
Exception: java.lang.InstantiationException: Error communicating with server: Lookup error: javax.naming.AuthenticationException: Invalid username/password for Config (guest); nested exception is: nested exception is: Exception in InitialContext: javax.naming.NamingException: Lookup error: javax.naming.AuthenticationException: Invalid username/password for Config (guest) at com.evermind.server.ApplicationClientInitialContextFactory.getInitialContext(ApplicationClientInitialContextFactory.java:149)
at javax.naming.spi.NamingManager.getInitialContext(NamingManager.java:662)
at javax.naming.InitialContext.getDefaultInitCtx(InitialContext.java:243)
at javax.naming.InitialContext.init(InitialContext.java:219)
at javax.naming.InitialContext.<init>(InitialContext.java:195)
at com.seagate.edcs.config.util.LookupUtility.getInitialContext(LookupUtility.java:123)
at com.seagate.edcs.config.util.LookupUtility.getConfiguration (LookupUtility.java:69)
at com.seagate.edcs.config.util.LookupUtility.main(LookupUtility.java:135)
Code Snippet:
* This method returns the Configuration for the properties set.
public ArrayList getConfiguration ( ) throws Exception {
ArrayList arrayList = null;
try {
Context context = getInitialContext();
System.out.println("Context : " + context);
Object home = context.lookup("java:comp/env/ejb/com.seagate.edcs.config.ejb.ConfigSessionEJBHome");
System.out.println("Object home : " + home);
ConfigSessionEJBHome configSessionEJBHome = (ConfigSessionEJBHome)PortableRemoteObject.narrow(home, ConfigSessionEJBHome.class);
System.out.println("ConfigSessionEJBHome configSessionEJBHome : " + configSessionEJBHome);
ConfigSessionEJB configSessionEJB =(ConfigSessionEJB)PortableRemoteObject.narrow(configSessionEJBHome.create(), ConfigSessionEJB.class);
System.out.println("ConfigSessionEJB configSessionEJB : " + configSessionEJB);
arrayList = configSessionEJB.getAllConfig();
System.out.println("Context : " + context);
} catch (Exception ex) {
System.out.println("Exception Occured");
throw ex;
return arrayList;
* Get an initial context from the JNDI tree.
private Context getInitialContext() throws NamingException {
try {
Hashtable hashtable = new Hashtable();
hashtable.put("java.naming.factory.initial", "com.evermind.server.ApplicationClientInitialContextFactory");
hashtable.put("java.naming.provider.url", "ormi://seagate.mil-shivas-270.am.ad.seagate.com/home"); // if we won't specify the port, it considers the default port
hashtable.put("java.naming.security.principal","ias_admin");
hashtable.put("java.naming.security.credentials","ias123");
return new InitialContext(hashtable);
} catch (NamingException ne) {
System.out.println("Exception in InitialContext.");
throw ne;
Note:
1. The user "ias_admin" & password "ias123" are the credential provided for the 'Admin' while installing the Oracle App Server and using these credentials I'm able to bring the Admin Console. Also, added new user 'guest/guest' - assigned this user to the 'admin' group ...
2. Since its a local lookup, there is no need to specify the credentials, but at runtime a dialog box pops up prompting to enter the 'userid/password' and when I enter the crendtials, I get the exception as stated. [In case of Servlet - EJB lookup, I'm not specifying any credentials]
Are there are any configuration parameters which I need to provide in any of the .xml? Could you please let me know the fix for the same.
Regards,
Kafeel/-

Please use the OS {forum:id=210}

WUO-709: Unable to get Property: Open == Forms application using Webutil

Hi everyone,
I have configured Webutil and tested a demo application for loading excel data into a forms application. The application works just fine. Here is the code:
DECLARE
application Client_OLE2.Obj_Type;
workbooks Client_OLE2.Obj_Type;
workbook Client_OLE2.Obj_Type;
worksheets Client_OLE2.Obj_Type;
worksheet Client_OLE2.Obj_Type;
filename                varchar2(2000);
cell Client_OLE2.OBJ_TYPE;
args Client_OLE2.OBJ_TYPE;
cell_value varchar2(100);
eod boolean:=false;
j integer:=1;
BEGIN
     -- The following set up communication with the excel spreadsheet
application := Client_OLE2.create_obj('Excel.Application');
Client_OLE2.set_property(application,'Visible','false');
workbooks := Client_OLE2.Get_Obj_Property(application, 'Workbooks');
args := Client_OLE2.CREATE_ARGLIST;
Client_OLE2.add_arg(args, 'c:\test\test.xls');
workbook := Client_OLE2.GET_OBJ_PROPERTY(workbooks,'Open',args);
Client_OLE2.destroy_arglist(args);
worksheets := Client_OLE2.GET_OBJ_PROPERTY(workbook, 'Worksheets');
worksheet := Client_OLE2.GET_OBJ_PROPERTY(application,'activesheet');
--Go to the first record
go_block('planets');
first_record;
loop
          If :system.record_status <> 'NEW' then
create_record;
          end if;
exit when eod;
     for k in 1..3 loop --3 fields per record
     args:= Client_OLE2.create_arglist;
Client_OLE2.add_arg(args, j);
Client_OLE2.add_arg(args, k);
cell:= Client_OLE2.get_obj_property(worksheet, 'Cells', args);
Client_OLE2.destroy_arglist(args);
cell_value :=Client_OLE2.get_char_property(cell, 'Value');
if upper(cell_value) = 'EOD' then
     eod:=true;
     Message('End of Data');
     exit;
end if;
--Could be done this way also ->
/*if k =1 then
     :dept.deptno:=cell_value;
end if;
if k =2 then
     :dept.dname:=cell_value;
end if;
if k =3 then
     :dept.loc:=cell_value;
end if;
--Less code this way ->
copy(cell_value,name_in('system.cursor_item'));
next_item;
     end loop; --for
     j:=j+1;
end loop;--main loop
-- Release the Client_OLE2 object handles
Client_OLE2.release_obj(cell);
Client_OLE2.release_obj(worksheet);
Client_OLE2.release_obj(worksheets);
Client_OLE2.release_obj(workbook);
Client_OLE2.release_obj(workbooks);
Client_OLE2.invoke(application,'Quit');
Client_OLE2.release_obj(application);
END;
-- cell_value :=Client_OLE2.get_num_property(cell, 'Value');
The issue comes when I try to supply filename and path (here, c:\test\test.xls) through a file open dialog. I tried each of these:
1.
filename := client_get_file_name
(directory_name => 'C:\'
,file_name => 'test'|| '.xls'
,file_filter => 'Excel (*.xls)|*.xls|'
,message => 'Select client side filename where App Server file will be saved'
,dialog_type => OPEN_FILE
,select_file => TRUE
2.
filename := Client_Get_File_Name(directory_name => 'C:\'
,file_name => null
,file_filter => null
,message => null
,dialog_type => null
,select_file => null
3.
filename := client_get_file_name ('','','','Select a file to Upload ',null,TRUE);
On using the above, I DO get a file open box. However, after browsing and selecting a file, I am getting the error message:
WUO-709 [OleFunctions.get_obj_property_args()] Unable to get Property: Open; Exception com.jacob.com.ComFailException: Can't map name to dispid: Open
I have checked the documentation on 'WUO-709' but cannot seem to figure out why it's not working.
Sorry for the lengthy description. Would greatly appreciate help on this.
- Amit

I forgot to mention that in the modified code, I am supplying 'filename' as:
filename := client_get_file_name ('','','','Select a file to Upload ',null,TRUE);
args := Client_OLE2.CREATE_ARGLIST;
Client_OLE2.add_arg(args, filename);
Thanks,
Amit

Unable to get RequestDispatcher for Context

Eclipse 3.3.0
Tomcat 6.0.16
Java 1.5.0_13
Mac OS X 10.5.6
Greetings:
I'm attempting to retrieve information cross context in my web application. I've attempted to enable cross context access by three means.
- I've added "crossContext=true" to the <Context> element in the server.xml of the Tomcat configuration under the Servers project of my workspace.
- I've added "crossContext=true" to the <Context> element in a META-INF/context.xml in the WebContent folder of my project.
- I've added "crossContext=true" to the <Context> element of the context.xml file in the conf directory of the Tomcat installation directory.
Yet despite these changes I'm still seeing "Unable to get RequestDispatcher for Context....Verify values and/or enable cross context access" in the console. What do I need to do to enable cross context access using Eclipse? Thanks for any help.
ETA - I've had this working before. I believe that I upgraded to Tomcat 6 from Tomcat 5.5 and that's when the jstl cross context actions broke.
ETA - I've got it working in Tomcat 6. The problem arises when I change the name of my webapplication from "foo" to ROOT inside eclipse. I want a jsp page in the ROOT web application to be able to access a servlet in the "bar" web application.
Edited by: nantucket on May 17, 2009 2:17 PM
Edited by: nantucket on May 17, 2009 2:26 PM

Thanks for your reply evnafets.
How many times do you declare your context???I know, I know... I got frustrated. :o)
But seriously, since my post I've discovered that it is "working" but not in the manner I had expected within the IDE. That is, if I access the page at
http://localhost:8080/ROOT/myPage.jspThen I can see the contents retrieved from the context bar. But if I use.
http://localhost:8080/myPage.jspI can see that the page somehow has been deployed to the root context, but the error code 500 appears in place of where the content from the bar context should be.
However, if I export war files for these two web applications and run them in Tomcat 6 outside of Eclipse, everything works as it should. So this is an eclipse issue with respect to deploying a web application to the root context. Maybe there is some configuration about that I must make somewhere.
I hope that makes sense.
Anyhow, the server.xml file contains the following..
<Context crossContext="true" docBase="bar" path="/bar" reloadable="true" source="org.eclipse.jst.j2ee.server:bar"/>
<Context crossContext="true" docBase="ROOT" path="/ROOT" reloadable="true" source="org.eclipse.jst.j2ee.server:ROOT"/>The jstl code in the jsp page accessing the context bar is the following.
<c:import url='/helloworld?action=view' context='/bar' />

New inst: HP-UX: db2icrt fails: CLP frontend unable to get request handle

We are migrating our installations from the beautiful AIX to ... HP-UX. I am told I will learn to love it, but probably not until they update df to at least 1988 levels.
This is the pilot install. We have never seen this work before (and maybe no-one has...?)
sapinst runs correctly up to the "Create database instance" phase. At that point it dies with the following:
FUNCTION: DB2 UDB, command line process, clp_start_bp, probe:3
MESSAGE : CLP frontend unable to get REQUEST handle
DATA #1: Hexdump etc.
DBI1281E: The database manager configuration file could not be read initialized.
No further useful information is provided.
In db2<sid> I have a bunch of dot files (.profile and the like) and the db2_software directory containing the database installation.
During the create database instance phase, I can see that directory sqllib is created, but it is deleted when the phase fails.
There is no litter of any kind in the /db2/<SID> directories, - nothing has been done at all.
I have done the following: <<imagine nice bullets below - they dont seem to be available here>>
checked that the permissions on /tmp and the installation direcctory (redirected by setenv TEMP /usr/sap/install) are 777: they are;
checked the OS parameters with db2osconf - they are good
checked the host name resolution with a perl script - gethostbyname and gethostbyaddr agree.
the ip address, simple hostname and FQDN are on a line in the hosts file
there is no litter from previous installations - this is a clean machine
I could not find any reference to required environment variables (such as LD_LIBRARY_PATH) in the install guide or the install note - so I have not set any.
I have been hacking away at this for days. I have put in a call to SAP, who will get back to me after dark (of course...)
This seems to be a massively popular problem, and the helpful error message ("Sorry, Sport, just can't bring myself to do it") seems to have people jumping from tall buildings and in front of busses all over Google-world. Furthermore there also seems to be a near-infinite number of possible causes and none of them seem to apply here.
H-PUX version is 11.31. DB2 is 9V5 patch 4. sapinst is latest available. Weekend is fading fast...
Edited by: Russell Day on Mar 5, 2010 7:46 AM

>
Paul Power wrote:
> Hi Russell,
>
> Apologies if some of this has been already tried but please check the following points:
>
> Make sure the machine name is listed in its hosts file.
>
> Make sure to log on directly to root. ie: do not su to root from another without '-'
>
> Make sure there is no instance created already (find / -name sqllib) for that user
>
> Using ps -aef and ipc -a, no old db2 ressources should be displayed for db2 instance owner. If there are any, kill/remove it
>
> You should make sure, that LIBPATH and LD_LIBRARY_PATH of root and db2 instance owner does not point to an path of another db2 version
>
> Regards,
> Paul
No need to apologise for assisting, Paul, but I have dealt with most of these.
The host file contains the unqualified and fully qualified hostnames, on the same line, unqualified first.
I am logging in as root (because there were no other users, and I'm old school, from when everyone logged on as root to do everything.
There is no instance, and in fact there is no sqllib except when the "create database instance" step is running.
The only detectable db2 process running is db2fcmd
I have not been able to find any instructions regarding LD_LIBRARY_PATH and LIBPATH for HP-UX. They are not mentioned in the installation guide at all. I cannot find it in any of the installation notes.   I presume sapinst is setting them itself before they are needed. Neither are set in the enviroment of db2<sid> or <sid>adm. I have gnawed my fingernails to the elbow over this one, but I cannot see any indication that either should be set for HP-UX. Anyway, they are definitely not set anywhere, to anything. This was a clean machine before I started chopping it up to do this install.
I figure it must be complicated - I have been trying to get an answer for 10 days already. I will absolutely hate myself when it turns out to be something obvious, documented in 10 places, mostly in bold italics. I shoulda taken my dads advice and been a riverboat gambler or a piano player in a cathouse - its a lot less complicated,

Unable to get the media from the Endeca Experience manager version 11.0.0

Hi.,
Iam unable to get the media from the Endeca Experience Manager for my endeca app 'CRS'.
I have created the endeca app named 'CRS' using the reference app discover-data-catalog-integration and successfully initialized and indexed.Iam able to see the Indexed data in my endeca_jspref and the configurations in my Experience Manager.
I want to import the media from my experience manager(this is my actual requirement) and for this iam executing the get_media.bat cmd from my application's control folder,the cmd was executing successfully without any errors, but the media folder was not populating with any images that i can see in the Experience manager .Please do the needful to resolve this issue.
ThankYou!!!
C:\>cd Endeca\apps\CRS\control
C:\Endeca\apps\CRS\control>get_media.bat
[07.04.14 11:48:08] INFO: Checking definition from AppConfig.xml against existing EAC provisioning.
[07.04.14 11:48:09] INFO: Updating provisioning for component 'DailyReportGenerator'.
[07.04.14 11:48:09] INFO: Updating definition for component 'DailyReportGenerator'.
[07.04.14 11:48:10] INFO: Definition updated.
[07.04.14 11:48:10] INFO: Exporting resource 'http://localhost:8006/ifcr/sites/CRS/media' to 'C:\Endeca\apps\CRS\control\..\config\media'
[07.04.14 11:48:11] INFO: Finished exporting resource.

What media are you trying to import? There won't be any media returned with get_media unless you but media in to begin with using the set_media cmd. However, it's preferable to use the media MDEX rather than storing media in the ECR.

Siebel 8.0.0.12 Fix Pack; Unable to get the seed from binary file.

Hello Folks,
Can anyone throw some light into what action is required on my scenario.
I have applied Fix Pack Siebel 8.0.0.12 on top of 8.0.0.11 SBA. After it is appled, I am facing a documented issue within the Release Notes for the 8.0.0.12 Fix Pack
The issue is "UNABLE TO LAUNCH URL AFTER APPLYING SIEBEL 8.0.0.12". I tried the steps given with the MR document, however, I am still having this issue.
I am also not sure what is expected at the step of; Run the following command: seedgeneratorutil myseed.dat abcdef .
It's asking me for a value to enter for seed at command prompt. "Enter the seed":
what I should give here. As an assumption values,I gave SADMIN and tried to launch but still shows up the same error
Please Assit
Steps Details from Release Notes:
UNABLE TO LAUNCH URL AFTER APPLYING SIEBEL 8.0.0.12
Component: Server Infrastructure
Subcomponent: SWSE
Product Version: Siebel 8.0.0.12
Base Bug ID: 11938270
**Users are unable to launch the URL after applying the Siebel 8.0.0.12 Fix Pack.
**Use the following workaround to address this issue:
Navigate to the eappweb/bin directory from the command line on the SWSE installation.
Run the following command:
seedgeneratorutil myseed.dat abcdef
NOTE: In the example, myseed.dat is a filename. You can give any file name you wish.
The myseed.dat file is generated in the eappweb/bin directory.
Edit eapps.cfg to include the following parameters under the SWE section:
seedfile = < complete path for myseed.dat >
Bounce the web server.
(For Linux only) Copy libmod_swe.so from the eappweb/bin folder to the web/ohs/modules folder
Thanks
Kumar

Wilson,
Thanks for your reply.I have repeated the steps and regenerated the error messages.
Browser
Message:
An error occurred while trying to process your request. This error indicates a problem with the configuration of this server and should be reported to the webmaster (along with any errors listed below). We apologize for the inconvenience
Initialization error:
Unable to get the seed from binary file.
Log
2021 2011-09-20 23:23:01 0000-00-00 00:00:00 +0530 00000000 001 003f 0001 09 ss110920_7068 7068 7852 E:\sba80\SWEApp\log\ss110920_7068.log 8.0.0.12 [20444] ENU
ProcessPluginState ProcessPluginStateError 1 000000024e781b9c:0 2011-09-20 23:23:01 7852: [SWSE] Unable to get the seed from binary file.
Eapps.cfg
[swe]
Language = enu
Log = errors
LogDirectory = $(SWSERoot)\log
ClientRootDir = $(SWSERoot)
SessionMonitor = False
AllowStats = true
LogSegmentSize = 0
LogMaxSegments = 0
DisableNagle = False
seedfile = E:\sba80\SWEApp\BIN\80012seed.dat
Thanks
Kumar

Wont get past "configuring updates stage 3 of 3 0%" and wont let me log into computer..HELP!!!

heres a picture of the screen i keep getting.
-HP Pavilion dv6700 as you can see its home premium
i kept getting a vista spyware alert saying i had 34 infected files and wouldn't stop and i also tried updating some things on my laptop while i updated to the new internet explorer 9. around 12noon today i rebooted my laptop to get all the updates to work and i got this configuring updates screen and was like ok. it kept going. it does it for a while, shuts down and restarts and goes back i didnt think anything was wrong made it to stage 3 and wont stop and move on from 0%. its now 10pm and its been doing it all day. ive tried shutting it down and rebooting myself but no matter what i do, it wont let me access my computer to do anything. i have avast virus protection but it said it was unable to move viruses to chest i pressed repair and it said it was postponed until next reboot so i did it this morning and figured its taking so long maybe because its trying to repair them but im sure it doesnt take 10 hours...im extremely upset. someone please help. and also, anyone know how i can get the viruses out? i dont have money for a better protection right now so im using my moms computer but she works on it so its hard. hp said they cant help because my warrenty is up, was a 1 year warrenty, got laptop in 2008 and warrenty expired in 2009. please help me.

After installing updates from Windows Update, you may get into a Reboot loop where you machines gets to “configuring updates 3 of 3. x% complete” then freezes or reboots.
Solution:
1a. Boot from the Windows System Repair Disc and choose the repair option in the lower left hand corner, choose System Restore, and select a Restore Point predating the attempted installation of the updates.
1b. If you don't have the DVD and the Vista/W7 came preinstalled on the machine, boot to the Recovery Environment using F8 at the HP logo during boot, choose "repair your computer" from the list, let RE load and do a system restore from there.
If restore fails, load the recovery environment command prompt and enter:
Del C:\Windows\winsxs\pending.xml
exit recovery environment and restart the pc, you may get 3 of 3 again but be patient, the desktop should load. Create a manual restore point and Turn off Windows Automatic updates until you can figure out which update caused the loop.
If you get it booting again:
You may be infected
Follow the order given below to disinfect your PC
1.) On a PC that is Not infected, Make a boot AV disc then boot from the disc on the Infected PC and scan the hard drive, remove any infections it finds, I prefer the Kaspersky disc myself. The New 2010 Kaspersky disc can update the AV dat files if you are connected to the internet at the time of scan and is suggested to update before the scan.
http://www.techmixer.com/free-bootable-antivirus-rescue-cds-download-list/
2.) Then boot into Windows:
Install free MBAM, run the program and go to the Update tab and update it, then go to the Scanner Tab and do a quick scan, select and remove anything it finds.
http://download.cnet.com/Malwarebytes-Anti-Malware/3000-8022_4-10804572.html
3.) When MBAM is done install SAS free version, run a quick scan, remove what it automatically selects.
http://www.superantispyware.com/download.html
These last 2 are not AV softwares like regular Anti Virus Software, they are on demand scanners that only scan for nasties when you run the program and will not interfere with your installed AV, these can be run once a day or week to ensure you are not infected. Be sure you update them before each daily-weekly scan.

Unable to load application configuration?

All of a sudden, a couple of weeks ago, adobe flash stopped working in Internet Explorer 10. I've gone through all the steps I can find on the forum to try to get it
to load. I even uninstalled it and the plug in for firefox, but it still wouldn't download, even directly. The error message that boinks and shows up as the exe file is installing it is:
Unable to load application configuration.
I'm running windows 7 pro 64 bit, service pack 1
Internet Explorer 10, 10.0.9200.16635 v 10.0.7
Adobe Flash version is gone, now that I uninstalled it to try to install, but was trying to install the update that it alerted me to, that is version 11.8.800.94, I think.
I went away from IE when there was no adobe flash for 64 bit, but came back and have enjoyed it. I see others have had similar problems, seemingly around installing an update.
Thanks for anyone's help.

Download and run the offline installers from http://helpx.adobe.com/flash-player/kb/installation-problems-flash-player-windows.html#mai n-pars_header (nder the heading Progress bar hangs...).

Unable to get a connection for pool - ResourceUnavailableException

Hi
I have a BPEL process which starts a child instance of another asynchronous BPEL process for each message in an XML file. The child BPEL process makes a call to the Oracle Apps JCA Adapter to push the data into E-Business Suite.
All works perfectly except when the number of messages exceeds a certain limit (15 or so). The error received is as follows:
"Exception occured when binding was invoked.
Exception occured during invocation of JCA binding: "JCA Binding execute of Reference operation 'SyncPersonRecord' failed due to:
JCA Binding Component connection issue. JCA Binding Component is unable to create an outbound JCA (CCI) connection.
ebsPeoplesoftEmployees:SyncPersonRecord [ SyncPersonRecord_ptt::SyncPersonRecord(InputParameters,OutputParameters) ] :
The JCA Binding Component was unable to establish an outbound JCA CCI connection due to the following issue:
javax.resource.spi.ApplicationServerInternalException:
Unable to get a connection for pool = 'eis/Apps/Apps',
weblogic.common.resourcepool.ResourceUnavailableException:
No resources currently available in pool eis/Apps/Apps to allocate to applications.
Either specify a time period to wait for resources to become available, or increase the size of the pool and retry.. Please make sure that the JCA connection factory and any dependent connection factories have been configured with a sufficient limit for max connections.
Please also make sure that the physical connection to the backend EIS is available and the backend itself is accepting connections. ".
The invoked JCA adapter raised a resource exception.
Please examine the above error message carefully to determine a resolution."
Obviously what is happening is the connection pool maximum is reached (currently 15) and this is throwing the error.
What I need to do is to implement the suggestion of "specifying a time period to wait" and I was hoping someone could tell me how I do this?
I have tried setting the 'Connection Creation Retry Frequency' parameter to 30 seconds which made no difference and also have checked the documentation on "Configuring and Managing JDBC Data Sources for Oracle WebLogic Server".
Does anyone know if this is something that is implemented directly in the BPEL process/composite or in the connection source itself.
Many thanks

Open the jndi : eis/Apps/Apps in /console - config tab - increase the initial and max conn capacity and save it. Retry the scenario

AnyConnect - Posture Assessment Failed: Unable to get the available CSD version....

Hello all
I am attempting to get the HostScan posture assessment working so we can check that any device connecting to the ASA is a valid corporate asset.
I have installed the posture module onto our test client machine (Windows 8.1) using the following software:
anyconnect-posture-win-4.0.00061-pre-deploy-k9
Then in ASDM under Remote Access VPN > Host Scan Image I have uploaded the following package:
disk0:/hostscan_3.1.06073-k9.pkg
...and ticked the box 'Enable Host Scan/CSD'.
Under Remote Access VPN > Secure Desktop Manager I have configured an initial simple Prelogin policy to test it working, this simply just checks that the OS is Windows 8. A success should map this user to a Group Policy I have created that is mapped to a Connection Profile.
So, with all that said, when I try to connect I see that the AnyConnect client going through the motions: "Posture Assessment: Checking for updates....", after which I get a pop-up and error message:
"Posture Assessment Failed: Unable to get the available CSD version from the secure gateway"
A bit stumped here and haven't quite found much on the web as to how to resolve this.
Has anyone encountered this before? If so, can you advise on what I can do
By the way I am connecting using IKEv2 (IPsec) as these are the requirements and the AC version is 4.0.00061, ASA version: 9.2(1).
Many thanks

Hello
Please forgive the shameless bump. Was hoping someone could help?
Many thanks

Unable to get tunnel configured

Similar Messages

Maybe you are looking for