Unable to see images in MAX

I have a SenTech USB camera and recently purchased the NI Vision software. Failing to sufficiently program in LabView to get an image using the SDK from SenTech I thought I might try to use the built in frame grabbers with Vision. Seeing as I needed a configuration name from MAX, I thought I'd try MAX to run the camera first.
So I open MAX and go into the Devices and find my camera properly identified. "cam0 : StUSBcam". But when I hit snapshot or play I get the following unknown error:
0x80040217
The message is "Unknown error" which is not terribly helpful. I would like to get back to the point where I am programming in LabView using the new IMAQ Image.ctl that I just bought but I wouldn't mind getting the camera to acknowledge me first.
If anyone has any experience with the SenTech SDK I'd love to pick your brain.
-Ken

Hello EverSong,
I decided to prod my camera again in MAX and discovered a setting which read "1360 x 1024 UNKNOWN 15fps". When I changed this setting to "1360 x 1024 32RGB 15fps" or 16RGB or 8Mono(?) the camera no longer threw an unknown error and was able to display an image of varying quality.
Initially I had tried to create a LabView program using SenTech / NI .vi's and the IMAQ vision .vi's. I set my image to be RGB (U32) and once I sized it properly, got not one image, but 16! I attach a picture of the alternating purple and green images from that attempt.
Having learned about Bayer filters from SenTech I tried applying a Bayer decoder to a Greyscale (U8) image and just got garbage. That image and program I have also attached. The program initializes the camera, sets the trigger to free run, sets the scan mode to full scan, and starts the transfer. The program that created the 16 pictures is the same except the source image was RBG (U32) and the output of "SNAP" fed directly into Image 2.
Attachments:
LabView_Image1.JPG ‏233 KB
Img_Bayer.JPG ‏247 KB
Prgm_Bayer.JPG ‏129 KB

Similar Messages

InDesign Unable to See Image in Preview

I'm very new to InDesign (day 1) and am working on a template for a flyer. I am unable to see one image when I do a preview. It does not appear when I export the file. The forum is not allowing me to attach the file. I have checked the attributes and the Nonprinting is NOT checked. I have the file uploaded to my Dropbox and will need an e-mail address if you would like me to share it to you. I don't know why it's not letting me attach on these forums . . .

Petteri_Paananen wrote:
Scott Falkner wrote:
Try re-saving the EPS as an Illustrator AI file. That’s the better format. If you’re saving EPS files for use in InDesign you’re doing something wrong.
That´s true if it´s vector graphics. I assumed (may be too fast) that original problem file is photoshop-eps, because I myself have had so little troubles with vector based eps-files in indesign.
It’s also true for mixed raster and vector and for raster only. TIF, PSD, or PDP are all superior to EPS when saving from Photoshop.

When "allow pages to choose their own colors, instead of my selections above" is un-checked in the options menu, I am unable to see images on websites. How do I maintain having the box un-checked and still view images?

I recently decided to switch the colors around in Firefox. I work in a pretty dark environment and having dark colored text on white or bright backgrounds is rather difficult on my eyes in the dark.
I switched the background to a dark gray, the text to a light gray and both visited and unvisited links to a light blue. Along with these changes, I unchecked the "allow pages to choose their own colors, instead of my selections above" box.
After unchecking the box, I am no longer able to view images on many websites. The images all turn gray - as if Firefox has changed their image into part of the background. When I check the box, I am able to see images fine, however, the websites usually revert back to their bright backgrounds with dark text.
Any help and assistance with this is greatly appreciated!
Thank you!

You can use the NoSquint extension to set font sizes (text/page zoom) and text colors on web pages.
* NoSquint - https://addons.mozilla.org/firefox/addon/2592

XML Publisher Report - Unable to see image stored on External server

Hi
I need to put image on XML report that is on different instance for that i had put a dummy image on XML template and in the WEB TAB for that image i put the tag like url:{ATTRIBUTE3} and attribute3 is having correct value we are also showing it on the report , but at the run time i can only see the dummy image of the template and the URL, not the actual image , URL points to a image on different server we can see the image when we place that URL in Web browser.
Please help me , Thx in advance.
Ranga

From the documentation:
URL Reference
1.Insert a dummy image in your template.
2.In Microsoft Word's Format Picture dialog box select the Web tab. Enter the following syntax in the Alternative text region to reference the image URL:
url:{'http://image location'}
For example, enter: url:{'http://www.oracle.com/images/ora_log.gif'}
Element Reference from XML File
1.Insert a dummy image in your template.
2.In Microsoft Word's Format Picture dialog box select the Web tab. Enter the following syntax in the Alternative text region to reference the image URL:
url:{IMAGE_LOCATION}
where IMAGE_LOCATION is an element from your XML file that holds the full URL to the image.
You can also build a URL based on multiple elements at runtime. Just use the concat function to build the URL string. For example:
url:{concat(SERVER,'/',IMAGE_DIR,'/',IMAGE_FILE)}
where SERVER, IMAGE_DIR, and IMAGE_FILE are element names from your XML file that hold the values to construct the URL.
This method can also be used with the OA_MEDIA reference as follows:
url:{concat('${OA_MEDIA}','/',IMAGE_FILE)}
Edited by: stevencallan on Feb 13, 2009 3:50 PM

Unable to see Images in LR

I am only able to see any images when I am in develop mode in LR. Both in version 2.7 and 3. I have no issues on my PC running Windows 7 but on my laptop also running Windows 7 I have tried uninstalling and reinstalling an still cannot figure it out. I am not finding anything that can help me with my problem. Can anyone tell me what might be wrong?
Thanks in advance!
Pam

Pam,
There are 2 possible reasons for this behaviour:
1) Corrupted previews
Try renaming the [catlogname] Previews.lrdata folder right next to your catalog when LR is closed. This will have your previews re-rendered the next time you start LR and go to Grid View.
2) Corrupted display profile
If you have a hardware calibration device, try re-calibrating and re-profiling your display.
Beat Gossweiler
Switzerland

Unable to see images in iTunes Store

Everything seems to be working fine except for the images. The only thing I see are grey boxes.
I have no idea what caused this problem and I don't know how to fix it. Any ideas?
SAMSUNG R540

Hi, aasia_.
Thank you for visiting Apple Support Communities.
Here are some troubleshooting steps that I would recommend going through for this issue.
Apple software on Windows: May see performance issues and blank iTunes Store
http://support.apple.com/kb/TS4123
Cheers,
Jason H.

Unable to see image in Yahoo mail from iphone, show images is turned on. IE8 works.

I am able to see the image when I reply to the email, but not in the original email. When I look at the original email in IE8 I am able to see the image. I am using Yahoo Email Beta in both browsers.
Thank you.
Tom

You can use these steps to check if images are blocked:
* Open the web page that has the images missing in a browser tab.
* Click the website favicon ([[Site Identity Button]]) on the left end of the location bar.
* Click the "More Information" button to open the "Page Info" window with the Security tab selected (also accessible via "Tools > Page Info").
* Go to the <i>Media</i> tab of the "Tools > Page Info" window.
* Select the first image link and scroll down through the list with the Down arrow key.
* If an image in the list is grayed and there is a check-mark in the box "<i>Block Images from...</i>" then remove that mark to unblock the images from that domain.

Can Not See Images On 1 Site

HELLO,
Can someone please help me, I am still trying to learn my MAC.....
I go to a website, which I noticed it only does it with the one website, but I am unable to see images. It does not give a error message or anything, but once on the site, try to click on the tabs to see different categories, it does not show any pictures, which it is suppose to.I tried from my Windows computer and it shows. I think I am missing something , on how to get images to show, but its only on that site- Essence Website ? Can someone help please.
THANK YOU VERY MUCH !

From the Safari menu bar, select
Safari ▹ Preferences ▹ Extensions
Turn all extensions OFF and test. If the problem is resolved, turn extensions back ON and then disable them one or a few at a time until you find the culprit.
If you wish, you may be able to salvage the malfunctioning extension by uninstalling and reinstalling it. That will revert its settings to the defaults.

I have elements 12 in Windows 7 but is unable to see mp4 files in the organiser. The sound from the file is there but no image!

I have elements 12 in Windows 7 but is unable to see mp4 (Canon G16) files in the organiser. The sound from the file is there but no image!
Other file formats from Canon is no problen. So What to do??
Roger

Me again,
A friend suggested that I do a system restore.
I did a search for system restore in Windows 7 and got a very intuitive menu.
I selected an earlier system restore point and executed the restore.
After the computer restart I reloaded Firefox 5.0 and the Ask.com problem was corrected.
My friend says this approach may work about 25% of the time to fix this kind of problem. In my case it worked and I am happy.
Thanks all.
Richard Ryer

I am unable to see the images in Aperture trash, though there are a number indicated in the trash. I have "show all" selected. What settings am I missing?

I am unable to see the images in Aperture trash, though there are a number indicated in the trash. I have "show all" selected. What settings am I missing?

You may have an invisible filter on your trash.
Try the "Double Caggiano", as described in Frank Caggiano's User tip:
Images not appearing in browser, search filter is cleared
Regards
Léonie

Unable to see PXIe-8133 in MAX on host computer

Hi,
I seem to be running into a very basic problem. I'm trying to use the PXIe-8133 system in Real-Time but I am unable to detect the system in MAX. I can't even see an "Unconfigured RT System" with IP Address of 0.0.0.0 as it shows in the documentation. I've installed all of the drivers for the PXIe 8133 on my host computer found here:
http://joule.ni.com/nidu/cds/view/p/id/2030/lang/en, but this has not solved the problem.
One thing to note, when I attach a monitor to the PXIe-8133, it says: "System State: No Software Installed" and also "Can't Find Suitable Device for Drive C". But only one of our 2 PXIe-8133's is displaying this and we are not able to see the PXIe-8133 system in MAX even in the system which does not display these warning messages.
Thanks very much in advance for your help!
Steven

Hey Steven,
So a couple things to make sure of:
1. Reboot your PXI and when it is rebooting up keep hitting the delete key until you see an output on your screen that gives you different options to select.
2. Go over to Real Time menu (think it is like the fourth option from the left on the top).
3. Once in here the first option is what mode of Real-Time do you want to access. Select LabVIEW Real-Time Safe Mode.
4. Go to the last menu option and save changes. This will reboot into the mode we just set.
Once it is rebooted, go into MAX on your computer that is on the same subnet as this PXI and refresh remote systems. You should now see a device with an IP address of 0.0.0.0. Make the changes to the IP address that you want. Once you save those changes it will reboot the PXI. If you are still not able to get the target showing, try to go back into the bios and there is also another option to choose under the Real-Time heading to reset IP by hardware switch, software or none. Change that to software. Save again and then it will reboot and see if you can now see it in MAX and make the corresponding IP changes.
David A.
National Instruments
Applications Engineer

Unable to see RAW NEF image from Nikon D300 in CS3

Have Camera Raw Plug-in Version 4.0 in my PS CS3 and am not able to see images from my recently purchased used Nikon D300. I have no problems seeing the NEF images downloaded from my Nikon D80. I typically download the images from my camera thru Lightroom 2.4. Do I need a more recent Camera Raw Plug-in? I want to make sure I'm still compatible with LR. Any suggestions will be hellpful.

Yes, you are outdated with the RAW plug in and probably not able to use the
correct version that supports your camera.
You have two options:
1- upgrade to CS4 and benefit from all other good this has to offer
2- If you won't or can't upgrade use the DNG route, DNG is a free offered
(by Adobe) converter. The latest DNG converter will convert your D300 files
to the open DNG format which will show your RAW (then as DNG but still the
same quality) files and you will be able to use it in CS3.
There is lot's of information about in on this page:
http://www.adobe.com/products/photoshop/cameraraw.html
Have Camera Raw Plug-in Version 4.0 in my PS CS3 and am not able to see images
from my recently purchased used Nikon D300.

Unable to see interface on ASA 5510 Firewall

Hi All,
I am unable to see 4th interface on my firewall i.e fastether0/3 on my firewall ASA 5510.
Below is the output.
ciscoasa# sh int ip br
Interface                  IP-Address      OK? Method Status                Protocol
Ethernet0/0                x.x.x.x           YES CONFIG up                    up
Ethernet0/1                x.x.x.x           YES CONFIG up                    up
Ethernet0/2                unassigned      YES unset administratively down down
Internal-Control0/0        127.0.1.1       YES unset up                    up
Internal-Data0/0           unassigned      YES unset up                    up
Management0/0              192.168.1.1     YES CONFIG up                    up
Please suggest what could be the reason.
Regards
Pankaj

Hi Ramraj,
Even i have the base license for my ASA 5510 which is showing all the 4 interfaces in sh ver. I don't think so license would be an issue. There should be some IOS code bug that needs to be upgraded. If this goes for an OS upgrade it should get resolved.
Its not showing up in sh ver . As Karsten said he might be running on old IOS version.
fy-a# sh ver
Cisco Adaptive Security Appliance Software Version 8.4(4)1
Device Manager Version 6.4(5)
Compiled on Thu 14-Jun-12 11:20 by builders
System image file is "disk0:/asa844-1-k8.bin"
Config file at boot was "startup-config"
fy-a up 1 day 1 hour
Hardware:   ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW016 @ 0xfff00000, 2048KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
                             Boot microcode   : CN1000-MC-BOOT-2.00
                             SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
                             IPSec microcode : CNlite-MC-IPSECm-MAIN-2.06
                             Number of accelerators: 1
0: Ext: Ethernet0/0         : address is 2c54.2d0c.8f1a, irq 9
1: Ext: Ethernet0/1         : address is 2c54.2d0c.8f1b, irq 9
2: Ext: Ethernet0/2         : address is 2c54.2d0c.8f1c, irq 9
3: Ext: Ethernet0/3         : address is 2c54.2d0c.8f1d, irq 9
4: Ext: Management0/0       : address is 2c54.2d0c.8f1e, irq 11
5: Int: Not used            : irq 11
6: Int: Not used            : irq 5
Licensed features for this platform:
Maximum Physical Interfaces       : Unlimited      perpetual
Maximum VLANs                     : 50             perpetual
Inside Hosts                      : Unlimited      perpetual
Failover                          : Disabled       perpetual
VPN-DES                           : Enabled        perpetual
VPN-3DES-AES                      : Enabled        perpetual
Security Contexts                 : 0              perpetual
GTP/GPRS                          : Disabled       perpetual
AnyConnect Premium Peers          : 2              perpetual
AnyConnect Essentials             : Disabled       perpetual
Other VPN Peers                   : 250            perpetual
Total VPN Peers                   : 250            perpetual
Shared License                    : Disabled       perpetual
AnyConnect for Mobile             : Disabled       perpetual
AnyConnect for Cisco VPN Phone    : Disabled       perpetual
Advanced Endpoint Assessment      : Disabled       perpetual
UC Phone Proxy Sessions           : 2              perpetual
Total UC Proxy Sessions           : 2              perpetual
Botnet Traffic Filter             : Disabled       perpetual
Intercompany Media Engine         : Disabled       perpetual
This platform has a Base license.
Serial Number: JMX1AXXXXX
Running Permanent Activation Key: XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Configuration register is 0x1
Configuration has not been modified since last system restart.
fy-a#
Ramraj please do correct me if am wrong.
Please do rate if the given information helps.
By
Karthik

When using the camera downloader in Adobe Bridge CS6 with Nikon D5200 we are unable to see previews of the photos and it is very slow to download. The issue occurs under a the users rights, but not under admin level. This is a new issue

When using the camera downloader in Adobe Bridge CS6 with Nikon D5200 we are unable to see previews of the photos and it is very slow to download. The issue occurs under a the users rights, but not under admin level. This is a new issue.

Hi Jdentremont,
Lync client gets user photos by first querying the Address Book Web Query (ABWQ) service on the server, which is exposed through the Distribution List Expansion web service. The client receives
the image file and then copies it to the user's cache to avoid downloading the image each time it needs to be displayed. The attribute values returned from the query are also stored in the cached Address Book Service entry for the user. The Address Book Service
deletes all cached images every 24 hours, which means that it can take up to 24 hours for new user images to be updated in the cache on the server.
To troubleshoot your problem, please follow the steps below:
1. Navigate to
“X:\share\1-WebServices-1\ABfiles\000000000\000000000” folder. (ABS file share)
You should see some photo files in this folder as the following screenshot.
2. Delete all the files in this folder.
3. On test PC, delete local cache files.
%userprofile%\AppData\Local\Microsoft\Office\15.0\Lync\[email protected]
4. Sign-in Lync with the test account.
5. Go back to the ABS file share, check if there is any Photo file in the folder.
Best regards,
Eric
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Unable to create image buffer after RAM preview

Running into an odd and frustrating error. Built a comp using the new Ray-traced 3D renderer and now I'm regretting being an early adopter big time with all the problems I've been encountering with it. The latest comes whenever I do a longer RAM preview in an attempt to watch the whole duration of my comp. It will get to about 170 frames or so, at which point I've interrupted by pressing spacebar because I don't need to see all the way to the end of my work area (around 220 frames). It'll play the RAM preview back fine, and even loop it, but as soon as I stop playback, I get this error message: "After Effects warning: Unable to create image buffer." There's only one button: "okay" and as soon as I click it the same error pops up again and it will never go away, forcing me to close AE from the task manager. I've taken to saving before every RAM preview like I used to do with Flash before previewing my buggy swfs for fear I'll lose all my work after previewing. Any ideas about what might be causing this?
Some more details about my comp:
1920x1080 @ 29.97
Ray-traced 3D
About 70 3D layers (I'm guessing this is my downfall - new renderer not designed for this many layers?)
Running Windows 7 Professional
i7 2600K
32GB RAM
2x GTX 570 video cards running latest driver (301.42, CUDA 4.2.1)
508GB free on my 2TB internal drive where the project and cache lives
From my GPU info window in case it's useful:
Fast Draft:
Available
Texture Memory:
600.00 MB
Ray-tracing:
GPU
OpenGL
Vendor:
NVIDIA Corporation
Device:
GeForce GTX 570/PCIe/SSE2
Version:
3.0.0
Total Memory:
1.20 GB
Shader Model:
4.0 or later
CUDA
Driver Version:
4.2
Devices:
2 (GeForce GTX 570, GeForce GTX 570)
Current Usable Memory:
1.04 GB (at application launch)
Maximum Usable Memory:
1.25 GB

Yeah, some buffer is very likely not flushing when you interrupt the preview and then there is no more memory on the graphics hardware. Consider setting the work area and your preview options to use only the work area. if it finishes the preview "correctly", it may not suffer the issue. Beyond that - raytracing doesn't/ shouldn't care about the number of items. The math is such, that it makes no difference whether you render a million polygons or just one. Of course there are still limitations due to the GPU dependency, but I doubt you ever truly exhaust the cards' geometry buffers. Compared to pixel data that is a small amount...
Mylenium

Unable to see images in MAX

Similar Messages

Maybe you are looking for