Upgraded from Linksys WRT54GX4 to WRT600N, severe loss of performance!

I have a WRT54GX4 with a WPC54GX4 adapter card. I enjoyed a rock solid 240Mbps signal thru out my apartment.
This weekend I upgraded to a WRT600N with WPC600N adapter card. I mainly wanted the Gigabit wired network for my desktops PC's but was hoping for even better performance with my laptops. If I sit at my desk where the router is located, I get around 180 Mpbs. If I move to the next room, the signal drops to about 27 - 81 mbps. What is up with that? I really didn't expect a loss in performance!
One laptop still has a 54 adapter card and that signal is great, steady everywhere in the apartment. But the laptop with the WPC600N sucks. I can't help but think that I just don't have something configured right.
Any help would be appreciated.

Try changing the wireless channel on the router & see if WPC600N connects or not ...

Similar Messages

Will Upgrading from 4 GB to 8 GB RAM Improve Performance

I have a 2009 2.0GHz Mac Mini with 4GB RAM. I use Photoshop CS4 and Lightroom 3 to process digital images. Lately, I'm processing higher megapixel files. I've gone from 10MP to 15MP and 18MP and would like processes to go faster.
Do you think that I'll see a significant gain in performance going from 4 to 8 GB RAM?

You may see some performance increase, but Photoshop CS4 can't address more than 4GB of RAM (it actually won't use that much, but I don't remember the exact figure), so expanding to 8GB won't be of as much benefit as it would if you upgraded to CS5 which is a 64-bit application and so is capable of addressing more RAM.
Regards.

Upgraded from 10.4.11 to 10.5.8 and lost mail in several Smart Mailboxes

I upgraded from 10.4.11 to 10.5.8. Several of my Smart Mail Boxes lost all email content but others remained in tact. Now the ones that lost content don't accept emails that meet the criteria for the Smart Box.
Anyone have that experience? Any ideas on recapturing? I didn't back up my mail prior to upgrade.

Welcome to the Discussion,
Smart Mailboxes are only virtual mailboxes, and contain nothing -- they are the product of a search list, and messages must stay in their original mailboxes. All the messages will still in the originating mailboxes, unless something else you did impacted those actual mailboxes, so you should be able to rewrite the definitions for these Smart Mailboxes.
Ernie

Running Lightroom 6 on Windows machine (after having upgraded from LR5... While attempting to add or change music in the Slideshow module, LR unexpectedly quits. After several attempts at this, LR6 won't even launch properly...shows the splash screen but

Running Lightroom 6 on Windows machine (after having upgraded from LR5... While attempting to add or change music in the Slideshow module, LR unexpectedly quits. After several attempts at this, LR6 won't even launch properly...shows the splash screen but that's it. The program is buggy...need an update/revision quickly!!

If you're on Windows, check out a free program called Audacity--it's fantastic. With Audacity the process of converting a 48.000 kHz to 44.100 kHz is as simply as opening, changing the sample rate, and then exporting again, as an MP3.

Trying to upgrade from 4.2.10 to 5.1.1. Error message -37 says backup will result in loss of all contents on the phone.

I need to upgrade from version 4.2.10 to 5.1.1. When I try, I get the following error message: An error occurred while backing up this iPhone (-37). Would you like to continue to update this iPhone? Continuing will result in the loss of all contents on this iPhone.
How can I upgrade?

This writeup says you have a security issue. http://support.apple.com/kb/TS3694
Try following the troubleshooting steps under error 37.
Good luck.

WRT54GX4 has problem. Please read! Can solved? Not Tested from linksys?

Recently just bought WRT54GX4. I discovered that this wireless router from linksys did not cover the range that i want. Previously i own WRT54Gv5 which still is better can connect to internet until when i was in my garden. However, this router when i take my notebook just out of my room where the router is installed the wireless is disconnected. Had tried a few time by opening the properties by clicking the icon on the bottom right found out that. The SSID dissapear first then a few second later the connection broke. My position was just out side my room only. For those who have WRT54GX4 please let me know can this problem solved? It was worst than my WRT54G model which is cheaper.
Message Edited by whlee1 on 07-13-2006 06:32 AM

Try setting the Adaptive Channel Expansion to disabled (Unless you happen to be using a WPC54GX4). Also try channel 11 and change the SSID to some other than linksys. Lastly, set the ACK mode to NO ACK and 802.11e/QoS to disabled. These settings are found under "Applications and Gaming" -> "QoS"

I have transferred Aperture 3 from an old Imac to a new. Now I´m requested to put in the serial number for v2, which I upgraded from several years ago. I can`t find it, but have the serial number for the upgrade. What to do?

I have transferred Aperture 3 from an old Imac to a new. Now I´m requested to put in the serial number for v2, which I upgraded from several years ago. I can`t find it, but have the serial number for the upgrade. What to do? Can I find the original serial number in my old Imac?

You'll have to contact Apple. See Pro Application Replacement Serial Numbers

HT1420 I purchased an audio book several years ago. When I upgraded from a 2009 imac to a 2012 lion iMac, I was able to transfer all songs and media from my I-tunes account with the exception of my audio books. My apple I.D. I tunes account was same of

Upgraded from a 2009 to 2012 Imac with lion. Successfully transferred all media and music with exception of audio books. Same Apple I.D. & I-tunes account.
Apple support unable to help. Have done all the routine i.e: ITunes store, click on purchased, etc. Audio Books not shown in history.
Help

Audiobooks are currently a one-time only download (which I think is a requirement from audible.com who supply them). Have you not got them on a backup ? If not (and I don't know if this is what you've already tried) then you can try contacting iTunes support and see if they will grant you a re-download : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page, then Purchases, Billing & Redemption

HT204368 I recently upgraded from an iPhone 4s to an iPhone 5. I have a Motorola HX550 Bluetooth Headset which worked flawlessly with the iPhone 4s. However, since upgrading to the iPhone 5, I frequently lose audio when in the middle of a call. I am no

I recently upgraded from an iPhone 4s to an iPhone 5. I have a Motorola HX550 Bluetooth Headset which worked flawlessly with the iPhone 4s. However, since upgrading to the iPhone 5, I frequently lose audio when in the middle of a call. I am not certain whether it is a full disconnect or just an audio loss. The person on the other end reports still being able to hear me, however, I suppose they could hear me speaking over another source even if bluetooth disconnected. The loss of audio is always preceded by a quick shrill noise, so I can easily tell when it happens. All I have to do to fix the problem is to select Audio Source on the call screen, temporarily switch audio back to the iPhone, and then switch back to the headset, and then it starts working again.
Is is important to note that I am not the only one experiencing this issue:
This is a link to someone using the Motorola H19txt headset experiencing the same issue
https://forums.motorola.com/posts/94ac15ad7c
If you go to the Plantronics website and look at the "Ratings and Reviews" on the Voyager Legend you will see the same issue reported:
http://www.plantronics.com/us/product/voyager-legend (next paragraph is taken from the review since there is no direct link to the review.
Really nice Headset unless you own an Iphone 5. I own several Plantronics headsets and have always loved the quality/ performance. This headset seems not to be compatible with the new Iphone 5. In the middle of a conversation it will lose all incoming audio. This leaves you trying to switch audio sources really fast in order not to lose your phone call. Ive tried 3 legend headsets and they all do the same thing. Hopefully this gets fixed soon because the headset is really nice
Since this issue appears to affect multiple headsets from multiple vendors, I think it is fair to conclude that it is an issue with the iPhone5 bluetooth itself.
I am posting this as a new discussion as I don't see any other posts specific to this iPhone 5 Bluetooth issue. I would have reported this as a problem to Apple, but don't seem to be able to find a way to do this on the web. Hopefully they are already aware, but if not, maybe they will see i here.

here is an interesting thing: take the iphone and set lock screen to never. Now make an email with siri--be sure to activate her with call button. get to the body and get some text in there. then just stop talking. LOCK SCREEN APPEARS!!!!!! and of course you draft is gone.
There does seem to be a work around for some--maybe all these issues. Don't use the call button--use the buttons on the phone.
Siri seems to behave properly with scenerio above---sans call button. She does not go to lock.

Migration from Linksys G to Airport not working

I'm upgrading from a Linksys WRT54g to an airport extreme. The previous setup was the linksys and a 4 port hub with a combination of wired and wireless connections. Our apple server, printer and a few other devices are hardwired. We have about 10 imacs and 1 Vista laptop. All the wireless imacs and vista need to connect to the hardwired server to run a filemaker database and be able to print to the hardwired printer via wireless connection.
Some imacs are running OS 10.4.11 but that should still work with the AP extreme since it's multi mode for wireless g and N.
The airport extreme and an 8 port netgear Gb hub are replacing the previous setup.
I've used the Airport utility on a 10.5.8 imac to find and configure the Airport and most macs find it but I still don't have internet or lan connection. I'm using WPA because that's all the older macs will support. The internet connection is a T1. I'm also getting the 169.xxx.xxx.xx ip address for the airport by default. How can I change this to 192.168.1.1 and still use DHCP?
I'm also getting kernal panics on several of the G5 imacs while switching airport connections and/or after configuring this new wireless connection.
Are the any special considerations I should be aware or a firmware upgrade? I'm following the instructions very carefully. Doesn't the Airport extreme provide the DHCP for the ipv4 connections and shouldn't the wireless macs connect to other hardwired macs with no problem?
Thanks for any advice.
budgen

Welcome to the discussion area, budgens!
Can't answer all of your questions, but can offer some assistance.
I'm also getting the 169.xxx.xxx.xx ip address for the airport by default.
This is a self-assigned IP address which indicates that the AirPort is not connected to or is not currently communicating with a valid Internet connection.
How can I change this to 192.168.1.1 and still use DHCP?
You will continue to see the 169.x.x.x error until you have a good Internet connection.
By default, the AirPort Exteme will use the 10.0.1.x range for local network IP assignments. If you want to change this to the 192.168.x.x range, you would do the following:
Open AirPort Utility - click Manual Setup
Click the Internet icon
Click the DHCP tab
Change to the 192.168.x.x range on this page
By default, the AirPort Extreme will be at 192.168.1.1 if you use this range and have a valid Internet connection.
Message was edited by: Bob Timmons

Inplace upgrade from 2012 to 2012 R2 fails when nearly complete

Greetings,
I've tried several times to upgrade a Server 2012 Standard running Hyper-V to R2 several times now with no success.
The setup will start fine. There are no "compatibility" issues found or reported and the setup then proceeds as expected.
It gets all the way through the phases and past the installing features, reboots, does all the hardware devices install and completes that, then does another reboot and gives me a BSOD (sorry, windows could not start sad face)
It will then reboot again and just keep doing that until I catch the boot menu and select the option to roll back to previous Windows. It then goes through the revert process and gives me a functioning machine again.
It's very much like this thread:
http://social.technet.microsoft.com/Forums/windowsserver/en-US/23d088d4-9ce0-4f12-a8c5-9bde3979e372/windows-server-2012-r2-upgrade-fails?forum=winserver8gen
I have checked and there are NO disk volumes at all without drive letters
I have tried setting all Hyper-V and other 3rd party app services to manual and disabled
I tried disabling VT support from the bios (this was an issue on a workstation upgrading from Win8 to Win8.1)
I've unplugged all external drives and the UPS connection (only mouse/keyboard attached)
This server is running a full GUI, and apart from the UPS and RAID disk controller there are no other apps or software installed.
I am doing the install from a copy of all the DVD ISO files placed on a directory on the C: and there is over 550GB free space
I first tried this several months ago and gave up. I just tried again today with a newer ISO of 2012R2 but still the same issue.

There is a minor BIOS update that I will probably apply to be sure, although the release notes only say it is for additional support for newer CPU's. All drivers are either updated with ones that are already R2 supported, or are devices that say to just
use the drivers that come OOB in 2012/R2. This is a "white box" that I've built myself, but it effectively uses the same "enterprise class" components and is fully 2012R2 compatible.
I was able to do a clean install of 2012R2 using a different drive that I connected up, so I know the system is capable of running R2, the issue seems to be somewhere in the upgrade process that messes it all up. I'd rather avoid having to do a fresh install
at this time though.
Because the upgrade actually seems to get through all the steps of hardware detection etc I'm at a loss where the failure is. My first guess is that there is some "other" driver that the system has decided is more suitable for something (and is incompatible)
than the one I'm currently using.

TS2518 I started the upgrade from 3.2.4 to 3.3 yesterday and it stuck at Step & 97% complete

I started the upgrade from 3.2.4 to 3.3 yesterday and it stuck at Step & 97% complete overnight (~14 hours). Its a 71 GB library. I have no confidence there is anything actually happening. I've forced quit Aperature and used disk utility to repair links. Still seems to be stuck. Any ideas?

I have tried several times. Repair gets to 100% and stays that way.
I have Force Quit several times, rebooted mac, repaired permissions, reset PRAM. Each time I have to start Repair and at 100% it gets stuck. I let it sit for 5 Hours just to see if something was working in background. Now I have no library or photos (yes I know, the photos are there. I'll I have to do is start all over again. That shouldn't be hard with 150+GB of photos and the loss of all their settings, gps location, crops, color correction, etc).
Any other suggestions. Apple support won't help, unless I pay them for an update that broke my work.
TIA
Narvon

Upgrading from Tiger to Leopard on and external (FireWire) drive...

Hi all,
I'm pretty sure this has been discussed somewhere on the www but after several hours of research, I'm embarrassed to admit I'm ready to call it quits (unless someone more tech savvy than I can help <:o)
I've been running my OS on a WD 500GB FireWire for the past couple of years. Switched to it shortly after realizing that the 80GB HD on my MacBook was insufficient for my needs.
Now I'm getting ready to upgrade from Tiger to Leopard and I've got some issues. Most importantly, when I launch the installer and it requires me to restart my system, I do so through both methods (holding down the "option" key to start up using the external HD and also by just allowing a normal boot under the old drive). In neither situation do I ever get the option to select where I'd like to install the new OS. In fact, when I allow the normal start without the "option" key being pressed, I don't even get to see the option to begin an installation. When I hold down the "option" key, I get the Mac OS X Install DVD screen (directory on the DVD), but it never gets to the point where I can start the installation.
I'm at a loss and getting a little frustrated (which has been my problem since I started with Macs--been a long time PC user and I'm always looking for the difficult way of doing things--so I'm probably just being PC-stupid as usual >;o)
Any assistance with getting me on the path to continued righteousness would be greatly appreciated. Thanks very much in advance!
Ali T. Borahan
http://www.alisails.com
PS: Despite the fact that I'm PC-literate and Mac-stupid, I've managed to convince almost a dozen people to switch to Mac, simply because I'm hooked and love how the Mac community sticks together and helps one another (and also because I can't stand the Microsoft kingdom!!! <:o)

Insert the Leopard DVD in the optical drive and restart the computer. After the chime press and hold down the "C" key until the dark gray Apple logo appears on the screen. After the installer loads select your language and click on the Continue button.
When the menubar appears select Disk Utility from the Utilities menu. After DU loads select your startup drive's entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger, and 4.1 for Leopard) and/or TechTool Pro (4.6.1 for Leopard) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Continue with the installation process until you reach the point where you must select a Target drive. Select your Target drive then click on the Options button in the lower left corner of the dialog.
Select the Archive and Install option.
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
Your target drive must have repaired OK when you repaired it. Otherwise do not continue.
You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

Never upgraded from 4.7, should I?

I'm still running OS 10.3.9 and never upgraded from iTunes 4.7, so I'm wondering if I should, given all the problems folks are having with the version 7 updates.
I've purchased only three songs in my life, and don't particularly care about buying movies and TV shows. At some future date, however, I might want to buy another song and I'm currently blocked from doing that at the iTunes Store.
Of real concern: Is my 4.7 iTune Library so seriously different in format from libraries, etc. in higher versions that I risk mucking up things forever if I ever do upgrade?
Thanks in advance for your replies and advice.
Dual-boot G4 Mac OS X (10.3.9) PB 1400, PM 7600, PLW NTR, LW 360

When QT7 was first released there were a lot of problems reported on the iMovie and iDVD lists from people using OS10.3.9. These problems were far ranging from everything to jerky playback, loss of importing or exporting to cameras, encoding issues, etc. So many people had to try and revert back to QT6 leaving QT7 for the OS 10.4 folks.
Your problem is a bit strange sounding and not one I have run across before. So first thing you will want to try is running basic system maintenance.
My standard list of things to do first for these weird sort of problems, but I also tend to run these before I go to burn an iDVD project just to be safe. Keep in mind this list represents the programs I tend to use. There are several alternate programs that do the same things with some combining the functions of some of the ones below. So everyone has their favorites, but here are mine...
Run MacJanitor (free download) to do all the Unix Cron Maintenance scripts.
Run Disk Utility (Applications -> Utilities) and repair disk permissions on your start up drive (typically your internal drive). Also verify any other drives mounted on the system, especially any external drives that you use for iMovie and iDVD projects.
Run Preferential Treatment (free download) to check for corrupt/damaged application and system preference files.
Run Cache Out X (free download) to clear all system and application caches.
Reboot your Mac (after running Cache Out X you are given the option to restart the machine).
Patrick

Upgrade from 4.6C to ERP6.0 EHP4 NW7.01 fails on EHP_INCLUSION

Hello dear friends at SDN forums,
We are performing an upgrade from a 4.6C Non Unicode source release to a SAP ERP 6.0 EHP4 based on NW 7 EHP1 Non Unicode.
Every phase has gone more or less fine until the current phase EHP_INCLUSION in SAP EHPI tool.
We are trying to specify the stack file manually, cosu00B4 SAP EHPI does not find it automatically via RFC against Solution Manager. I donu00B4t discard a possible missconfiguration in the RFC destination "BACK" configuration (the one that points from our target system to the Solution Manager), but thatu00B4s another story.
Anyway, that shoulnu00B4t be relevant for the trouble Iu00B4m expressing.
As we are on source release 4.6C I must make use of the .txt stack file and not the .xml file, as per SAP notes.
The symptom: everytime I retry that EHP_INCLUSION phase, it complaints about "Sever errors detected. Error Code = -1. Reason: The stack configuration does not contain a product stack".
Iu00B4ll also paste here the contents of the EHP_INCLUSION.log trace file:
1 ETQ201 Entering upgrade-phase "EHP_INCLUSION" ("20100715150020")
2 ETQ367 Connect variables are set for standard instance access
4 ETQ399 System-nr = '00', GwService = 'sapgw00'
4 ETQ399 Environment variables:
4 ETQ399   dbs_ora_schema=SAPR3
4 ETQ399   auth_shadow_upgrade=0
4 ETQ380 computing toolpath for request "TP_DEFAULT"
4 ETQ382 translates to group "R3UP_TOOL_GROUP_OLD"
4 ETQ383 translates to path "D:\usr\sap\CES\SYS\exe\run"
4 ETQ383 translates to path "exe"
4 ETQ399 Set environment for standard connect:
4 ETQ399 ENV: dbs_ora_schema=SAPR3
4 ETQ399 ENV: auth_shadow_upgrade=0
4 ETQ399 Set RFC variables for standard connect:
4 ETQ399 System-nr = '00', GwService = 'sapgw00'
4 ETQ399 Set tool parameters for standard connect:
4 ETQ399   default TPPARAM: DEFAULT.TPP
1 ETQ200 Executing actual phase 'PREP_EXTENSION/EHP_INCLUSION'.
1 ETQ399 Phase arguments:
2 ETQ399 Arg[0] = 'ADDONEHP.DMP'
2 ETQ399 Arg[1] = 'NAVERSEHP.DMP'
2 ETQ399 Arg[2] = 'SPDA_EHP_INCLUSION.LOG'
2 ETQ399 Arg[3] = ''
2 ETQ730 Starting upload of all package files in "
dbapru001\sapmnt\trans\EPS\in"
4 ETQ010 Date & Time: 20100715150020
4 ETQ230 Starting RFC Login to: System = "CES", GwHost = "dbapru001", GwService = "sapgw00"
4 ETQ359 RFC Login to: System="CES", Nr="00", GwHost="dbapru001", GwService="sapgw00"
4 ETQ232 RFC Login succeeded
4 ETQ233 Calling function module "SPDA_PREPARE_PATCH" by RFC
4 ETQ234 Call of function module "SPDA_PREPARE_PATCH" by RFC succeeded
4 ETQ239 Logging off from SAP system
4 ETQ010 Date & Time: 20100715150024
2 ETQ732 Package descriptions uploaded successfully
4 ETQ399 EhP stack selection ...
4 ETQ399 Reading stack content ...
4 ETQ399 ... reading stack configuration file "C:\SMSDXML_CES.txt"
4 ETQ230 Starting RFC Login to: System = "CES", GwHost = "dbapru001", GwService = "sapgw00"
4 ETQ359 RFC Login to: System="CES", Nr="00", GwHost="dbapru001", GwService="sapgw00"
4 ETQ232 RFC Login succeeded
4 ETQ233 Calling function module "SPDA_GET_STACK_INFO" by RFC
2 ETQ399 Returned table ET_STACK_NCVERS:
2 ETQ399 Returned table ET_STACK_PACKAGES:
4 ETQ399 ... Error reading stack info (rc=-1, reason="The stack configuration does not contain a product stack")
That file was generated from Solman Mopz, was saved with a short path name just in case it could be problematic.
The Solman is on version NW 7 EHP1. Our 4.6C SPAM version is 50 (the latest available).
Iu00B4ve been fighting this issue for several days unsuccessfully, and it seems like thereu00B4s no documentation on it.
Iu00B4ve re-read SAP notes , master, EHP and upgrade guides several times, and also similar problems (but not exactly the same as mine) here at SDN forums.
Besides, now Iu00B4m having a problem to create customer messages to OSS which will last a few days (due an issue with our old installation number in SAP Service Marketplace). Thatu00B4s why Iu00B4m trying to obtain support from this forum, before we can obtain a response from SAP OSS.
Has anybody experienced something similar?
Thanks in advance for your help.
Javier

Hi FDK,
As far as I´m concerned, I promise I will write how we solved it when we get it.
The news are: at last we could create a customer message to SAP Support, and SAP has told us to:
1) Ensure that our Solution Manager is in a sufficiently high SP Stack level. In our case, as we have a Sol. Manager based on NW 7 EHP 1 with SP Stack level 20, they are asking us to apply SP Stack level 22 as first meassure.
2) In case we cannot afford to do the mentioned meassure immediately, then they suggest us another possibly working option: to downgrade our SPAM 4.6C from level 50 to 48. There is a SAP Note that explains how a reimport of a Support Package for SPAM can be done (and it seems like it´s even possible to downgrade the SPAM level, I didn´t know that):
SAP Note 684564: Re-importing a SPAM/SAINT update
So, now we are working on these suggestions. As the Solution Manager is really not "ours", but belongs to our SAP VAR (partner), we need to wait until they can schedule this technical task.
So, right now the immediate task I´m trying to perform is downgrading our SPAM 4.6C from level 50 to 48.
But, I have a problem and have just let know it to SAP in the customer message: I have no way to get such level 48 of SPAM 46C. SAP always only hosts the last (or the 2 most recent as much) version of SPAM in the Software Download Center of SAP Service Marketplace. Thus, right now if you navigate in SAP Service Marketplace you´ll only find the 50 level version of SPAM 4.6C. I´m again waiting for SAP ´s response concerning this.
Best regards,
Javier

Upgraded from Linksys WRT54GX4 to WRT600N, severe loss of performance!

Similar Messages

Maybe you are looking for