USB 1.1 but no USB 2.0 on MS-7125 [solved]

I have Gentoo AMD64 2005.0 with kernel 2.6.11-gentoo-r11 running on an MSI K8N Neo4 nForce 4 Ultra Platinum motherboard (MS-7125). I tried two different USB memory sticks. The first is recognized by the kernel with no problems. dmesg reports the following.
Code: [Select]
ohci_hcd 0000:00:02.0: wakeup
usb 2-2: new full speed USB device using ohci_hcd and address 3
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
Vendor: USB NAND Model: FLASH DISK Rev: 0.30
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 64000 512-byte hdwr sectors (33 MB)
sda: Write Protect is off
sda: Mode Sense: 0b 00 00 08
sda: assuming drive cache: write through
SCSI device sda: 64000 512-byte hdwr sectors (33 MB)
sda: Write Protect is off
sda: Mode Sense: 0b 00 00 08
sda: assuming drive cache: write through
sda: sda1
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
usb-storage: device scan complete
It evidently is USB 1.1 (OHCI). The second is not recognized. dmesg reports the following.
Code: [Select]
usb 1-2: new high speed USB device using ehci_hcd and address 6
usb 1-2: khubd timed out on ep0in
usb 1-2: device descriptor read/64, error -110
usb 1-2: khubd timed out on ep0in
usb 1-2: khubd timed out on ep0in
usb 1-2: unable to read config index 0 descriptor/all
usb 1-2: can't read configurations, error -110
usb 1-2: new high speed USB device using ehci_hcd and address 7
usb 1-2: khubd timed out on ep0in
usb 1-2: device descriptor read/64, error -110
usb 1-2: khubd timed out on ep0in
usb 1-2: unable to read config index 0 descriptor/start
usb 1-2: can't read configurations, error -110
The second is evidently USB 2.0 (EHCI). dmesg seems to indicate that things are OK with EHCI.
Code: [Select]
ehci_hcd 0000:00:02.1: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: irq 185, pci mem 0xfebfe000
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: park 0
ehci_hcd 0000:00:02.1: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
lspci -v reports the following.
Code: [Select]
0000:00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3) (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7125
Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 185
Memory at febfe000 (32-bit, non-prefetchable)
Capabilities: [44] #0a [2098]
Capabilities: [80] Power Management version 2
The BIOS has two settings for USB which allow only enable/disable and both are enabled. Also, a thread in this forum indicated that connections to pin 10, USBOC, might cause problems but I have nothing connected to that pin.
Has anyone got USB 2.0 working under Windows XP on this motherboard, MS-7125?
Edit: USB 2.0 (the ehci_hcd module in Linux) now works flawlessly using the newest kernel, 2.6.12-gentoo. In Linux, at least, good things happen to those who wait.
Edit2: USB 2.0 malfunctioned in later kernels while it worked under XP x64. I believe it depends on the kernel and maybe udev. Under my latest kernel, gentoo-2.6.14, and udev 071 USB 2.0 is restored.

maybe use a different OS or put this in the "operating system" section and see if they can help?

Similar Messages

IPod nano works with USB 1.1 but not USB 2.0

Anyone using an iPod nano that works with USB 1.1 but not with USB 2.0? I am using Windows XP and when installing the iPod software from CD it recognizes the iPod and am able to transfer songs using iTunes but when installing SP1 or SP2 to enable USB 2.0 transfers, Windows XP only recognizes the iPod nano as a USB Mass Storage Device. This is the same with iPod Updater.

I have a similar problem with the following configuration:
- Dell Dimension 4100 Desktop with 2 integrated USB 1.1 ports, Windows 2000 SP 4
- PCI 6-Ports USB 2.0 Card ("Mentor" resp. www.bona.com.tw), Model USB20-PCI/6P
What works well?
- All my USB add-ons (1.1 and 2.0) on the internal 1.1 ports as well as on the USB2.0 PCI card
- iPod Nano 4GB on internal 1.1 ports (external drive in windows 2000 as well as iPod in iTunes)
- iPod Nano works as well as on the USB 2.0 card ONLY WHEN my old 4-port USB1.1 hub is connected between Nano and USB card
What doesn't works?
My iPod Nano directly connected to the USB 2.0 card. Symptoms when connecting:
- Windows is very slow, process "scvhost.exe" or "system.exe" using 99% of CPU for some minutes
- iPod is recognised as external drive, but when I click on it, it is empty and copying files to it results in "I/O error"
- iTunes doesn't recognise the iPod (of course, if even windows itself cannot read from it...)
I removed all USB drivers, reinstalled iTunes, iPod (by the way, I still don't understand what "iPod update" is good for, except for updating the iPod's firmware), deactivate the internal USB1.1 ports, no result.
Help!!!!!!!!!!!!!!!!

Ipod works with USB 1.1, but not USB 2.0 (30GIG)

Has anyone had this issue? I plug my 30GIG iPod into a USB 2.0, and it says updating, do not disconnect for what seems like an eternity. Eventually, it pops up saying the ipod appears to be corrupted, restore to factory settings? I respond ok, and then it fails to restore. Tried multiple USB 2.0's, same thing.
Next, I pluged into my USB 1.1, and it pops up itunes (latest version) almost immediately, and shows the ipod, and allows me to xfer tunes immediately.
Any thoughts?
Thanks

I'm having a similar problem. I've tried reinstalling USB2.0 drivers, iTunes, iPod but cannot get it to work. It just shows up in the device manager as 'USB Mass storage device' with an exclaimation mark next to it. I've tried to update the drivers for the 'USB MAss storage device', however it just says that I've already got the most updated drivers for the device. I've succumbed to the 1.1 for now, but would really appreciate it if someone could shed some light on this situation!

Disabling USB hard drives but allowing USB keys mounting, possible ?

Hi all,
I have a tricky request from one of my customers : they would like to block any external hard drives (firewire and USB) from mounting on the Desktop, BUT would like to allow USB keys only.
All the clients are unmanaged (local accounts, NOT bound to an Open Directory Master server) and are running OS X 10.4.8 (Intel).
I found the easy way to prevent any Firewire device to show up.
I also found how to disable all USB devices (except for keyboard/mouse) : renaming /System/Library/Extensions/IOUSBMassStorageClass.kext
Problem is, this method won't make any difference between a hard drive and a key, it will block it, period.
Is there any way to allow some (or all) USB keys only to mount ? My only guess would be to unload some extensions which are listed by the "kextstat" command.
That could only be possible if USB keys and USB hard drives don't use the same kind/brand of controller/bridge and therefore don't use the same kernel extension.
Does anyone have a clue on this ?
Many thanks.
Mac OS X (10.4.8)

Hi all,
I have a tricky request from one of my customers : they would like to block any external hard drives (firewire and USB) from mounting on the Desktop, BUT would like to allow USB keys only.
All the clients are unmanaged (local accounts, NOT bound to an Open Directory Master server) and are running OS X 10.4.8 (Intel).
I found the easy way to prevent any Firewire device to show up.
I also found how to disable all USB devices (except for keyboard/mouse) : renaming /System/Library/Extensions/IOUSBMassStorageClass.kext
Problem is, this method won't make any difference between a hard drive and a key, it will block it, period.
Is there any way to allow some (or all) USB keys only to mount ? My only guess would be to unload some extensions which are listed by the "kextstat" command.
That could only be possible if USB keys and USB hard drives don't use the same kind/brand of controller/bridge and therefore don't use the same kernel extension.
Does anyone have a clue on this ?
Many thanks.
Mac OS X (10.4.8)

How do I use GarageBand as a amp/speaker to listen to my Electronic Drum set? I have a MIDI-USB cord already but I can't figure out how to listen to my set through the software using my computer speakers?

How do I use GarageBand as a amp/speaker to listen to my Electronic Drum set? I have a MIDI-USB cord already but I can't figure out how to listen to my set through the software using my computer speakers?

If you want to listen to the sounds of your drum set, you should use an audio cable and connect it to the computer's line-in, then create a real instrument track.
If you use a Midi/USB interface, you'll have to create a software instrument track and select one of GB's drumsets as the instrument. Hopefully your drumset's midi notes are mapped to the right sounds in GB.

TS1538 ipad does not come on once its unpluged from power source,it enters recovery mode when both power and home botton are pressed with usb on powersource but does not come up at all when connected to computer or out of power source

ipad does not come on once its unpluged from power source,it enters recovery mode when both power and home botton are pressed with usb on powersource but does not come up at all when connected to computer or out of power source

What model iPad do you have? If it's an iPad 1, the battery may have expired and needs replacement.
 Cheers, Tom

4s Hotspot tethering only works with USB and BT but not with wifi

Hi,
XP sp3 - iPhone 4s with ios 5.0.1 - on Three one plan
Tethering with wifi works to a friends Samsung phone, wifi on the pc confirmed working with the apple store wifi, tethering with USB and BT works with good connection speeds on my laptop but when i try to tether with wifi it connects to the laptop at 54mbps and all appears well, even claims to have received a small amount of data packets, but no data comes to any browser. The iPhone reports 1 connection to the hotspot and stays connected with a non-pulsing blue bar after the first minute.
In the PC i have tried this http://windows.microsoft.com/en-US/windows7/Change-the-order-of-network-protocol -bindings
I've deleted my firewall (zone alarm) completely and turned off windows firewall to go naked surfing for a second even though they don't cause a problem with USB tethering, makes no difference
I've deleted the network connection numerous times
"repaired" connection
dissabled and enabled the wifi
turned off the wireless with a hardware switch and on again
disabled bluetooth
rebooted many times
reinstalled itunes (latest)
loads more things i can't remember
This is causing me a nightmare. I've been through everything i can find online, been to the Apple store genius bar (genius appeared to have sub zero knowledge / interest as it involved a MS machine), been to a Three shop (legally not allowed to touch my PC apparently) and been to a Sony shop (laptop make, not their fault if my iphone doesn't work). All very frustrating.
Please help if you can! Any suggestion will be tried unless it involves sledge hammers or lakes, and only then for a few more days at most.

Turned off bluetooth on phone, turned off hotspot and on again, phone asked if i wanted to turn on bluetooth or go with USB and wifi only, said usb/wifi only. Still nothing. Rebooted PC and iphone. Turned on hotspot, pc seemlessly connects to network, still no data comes.
One odd thing is zone alarm asks me to "select a security zone for the wireless network at ip address: *******.0" every time and doesn't seem to remember the setting over sessions. When i get the status of the connection the ip address is *****.2 and default gateway is same ********.1 Not sure if that's anything.
Also getting a javascript error about an undefinded component (trustcheckermozilla) since i updated zonealarm but as i said even completely uninstalling zonealarm made no difference. I'll update firefox as well but tried with IE and still no data.

When i try to connect my iPhone 4S into iTunes through wifi or USB it will not connect the other thing is when i hook up my iPad into iTunes it will connect through wifi but not USB? Now is this a issue with my iPad and iPhone or is this iTunes?

When i bought my iPhone and my iPad they both were on iOS 7.0.2 i updated them shortly after thinking the new iOS 7.0.4 was better. i see its not but they both worked great with iTunes before and after the update. My question is why is my iPhone not connecting to iTunes? it will not connect through USB or wifi and i know that the setting to do that is turned on. my iPad connects through iTunes through wifi but not USB. This isnt making any sense but i wanna know is this a iTunes issue? or is it my phone and iPad??

This can sometimes be the result of a faulty/damaaged USB sync cable. Do you have another cable you could test it out with?
B-rock

I got lightning to usb camera adapter but get fault message on ipad mine "cannot use device" the connected usb device requires too much power

I tried to use lightning to usb camera adapter but every time I plug it into my ipad mine it give cannot use device. the connected usb device requires too much power. how could I use this attachment.

Or use the camera's SD card instead.
 Cheers, Tom

Zen Microphoto works with USB1.1, but not USB

I recently bought a Zen Microphoto 8gb. After some trouble installing it, i finally got it to work. My computer has 6 USB-ports, where 2 is USB. compliant, and 4 are USB2.0 compliant. I connected the Microphoto to one of the USB. ports, and Windows XP installed it automatically after a few seconds. This works fine.
But I want faster transfer speeds, so I connected the player to one of my USB2-ports, expecting it to work equally there. What happens when I do this, is that Windows XP acts as the player is not installed.. A message at the systray tells me "Creative Labs ZEN MicroPhoto found", and a driver install window pops up telling me to insert the included CD to install the driver (obviously because the driver now isn't implemented in XP)
I then tried to uninstall the players drivers and then plug it in the USB2.0 ports. Just the same problem.
Windows finds the drivers when connecting it to USB., but not when connecting it to USB2.0
I have Windows XP Service Pack 2 and Windows Media Player 0. Can anyone help me, as I am a music artist, and need a working MP3-player.
Thanks.

Hi,
I have the same problem actually. Works fine on my USB1.1, but it was a bit slow, so i bought a PCI USB 2 Card. When I plug it in, I get the generic hdd and nothing in iTunes. I got it working a few times in the USB2, but only after reinstalling and installing the iPod software, but it stops working the next time i connect to it.
Not sure what the issue is so far.

QuestionJust purchased a USB Super Drive but unsure how to use it - o instructions provided apart from how to eject a cd. Each time I put in a cd it just ejects it again.

Just purchased a USB Super Drive but unsure how to use it - o instructions provided apart from how to eject a cd. Each time I put in a cd it just ejects it again.Can anyone help.

USB is rarely bootable under Mac OS X and PowerPC Macs. Get a Firewire Superdrive from http://www.macsales.com/ if your intent is to boot the machine. PPC, which is PowerPC, indicates the Mac predates 2006.

Photoshop Elements 12 will not let me save files edited on a usb flash drive, but will photos on the hard drive all other apts will on the flash drive

Photoshop Elements 12 will not let me save files edited on a usb flash drive, but will photos on the hard drive all other apts will on the flash drive

Thanks for the information and your help. I have never bothered before changing the format. Next time I will.
I copied the library to the external drive and then it went and said they were referenced files but I was okay about that. Now it cannot see them and will not do anything with them. I think I will buy another external drive and start again by importing all of my files again. I guess 55K will keep the mac busy this week.

USB Drives works, but does not show up in "Safely Remove Hardware"

USB Drives works, but does not show up in "Safely Remove Hardware"
windows 8
USB Drives works, but does not show up in "Safely Remove Hardware"
Here are my symptom
- USB Flash Drives , USB External HDD works normally
- I can see them in "My Computer"
- I can open "Safely Remove Hardware" via Run Command, but there is no device in the list
- They show up as "Disk drives" in device manager
- When I right click their icons in "My Computer", there is no option to "Eject" them
- In "Disk Management", they show up as "Basic". Prior to this issue, they were "Removable"
After I tested, it seems that my Vista detects every USB storage device as a normal HDD.
I don't know why but I'd appreciate any help because I have to plug-in and remove those drives often, especially flash drives.
Thank you

Hello Mickey2003
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand you are having issues in Windows Vista with your USB Storage devices not showing up in the Safely Remove Hardware list. I am providing you with a link to a Microsoft Hotfix for this very issue titled An external USB storage device may not appear in the Safely Remove Hardware list in the notification.... I would recommend you review the KB document and ensure you a familiar with the Hotfix information and run the hotfix to resolve the issue you are experiencing.
Please re-post if you require additional support. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

H800-30ea,USB Drives works, but does not show up in "Safely Remove Hardware"

hi
USB Drives works, but does not show up in "Safely Remove Hardware"
Here are my symptom
- USB Flash Drives , USB External HDD works normally
- I can see them in "My Computer"
- I can open "Safely Remove Hardware" via Run Command, but there is no device in the list
- They show up as "Disk drives" in device manager
- When I right click their icons in "My Computer", there is no option to "Eject" them
- In "Disk Management", they show up as "Basic". Prior to this issue, they were "Removable"
After I tested, it seems that my Vista detects every USB storage device as a normal HDD.
I don't know why but I'd appreciate any help because I have to plug-in and remove those drives often, especially flash drives.
Thank you

Hello takpesar,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand you are having issues in Windows Vista with your USB Storage devices not showing up in the Safely Remove Hardware list. I am providing you with a link to a Microsoft Hotfix for this very issue titled An external USB storage device may not appear in the Safely Remove Hardware list in the notification.... I would recommend you review the KB document and ensure you a familiar with the Hotfix information and run the hotfix to resolve the issue you are experiencing.
Please re-post if you require additional support. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Hi all, i want create a bootable Mavericks USB key (8G) but installEDS. dmg does'nt exist in my HD. How can i dowload this. Thank you

Hi All
I want to create a bootable Mavericks USB key (8G) but installEDS. dmg does'nt exist in my HD. How can i dowload this?
Thank you

You just want to create a Mavericks USB thumb drive, right? If so, you don't need to erase Mavericks and you don't need to reinstall Snow Leopard.
While you're in Mavericks and at your Desktop, open the App Store. Go to the Purchases tab and click on the Download button on the right hand side across from OS X Mavericks. This will start the download of the OS X Mavericks installer. When it finishes and you see a screen that wants you to continue, go up to the menu bar and QUIT the installer (Install OS X). Do not click the Continue button.

USB 1.1 but no USB 2.0 on MS-7125 [solved]

Similar Messages

Maybe you are looking for