Verizon Router Needed?

Hello all,
I currently have FIOS TV/Internet service in my home. The TV service is NOT using any Verizon STBs, as I have TIVO deployed, but I am using a MCard in my main TIVO DVR. Do I still need to use the Verizon router or can I swap it out for a real router?
Thanks,
Steve

Should be able to use your own router.

Similar Messages

Can I have my Time Capsule wifi and my Verizon router wifi on at the same time?

I want to have my verizon wifi on at the same time as my time capsules wifi but I don't know if it interfere. There's an app that you can use as a remote for your cable box but you need to be on your routers wifi.
Thanks,
Zach

Suggest that you run a few speed checks on both wireless networks with a computer in same room as the wireless router using a site like www.speedtest.net on your browser.
If you are getting close to your plan speeds, then you likely do not have interference issues.
Most routers will scan to find the best available channel to use, so assuming that your equipment is working OK, things should be OK. Try to keep the Verizon router and Time Capsule at least 6-8 feet, or a few meters from each other.
This assumes that you are not living in a crowded situation like an apartment complex, where intereference is pretty much a fact of life due to the very limited number of wireless channels that are available.

How to create Windows 7 Homegroup with Verizon Router

I have a desktop and a laptop, both running Windows 7 (the desktop is running Windows 7 Home Premium, the laptop is running Windows Ultimate). With XP I had a nice network and could share printerhs, files, etc .
After I upgraded both machines from XP to windows 7 I cannot get the homegroup to create AND share. I can create a homegroup on either machine, but in either case the other machine cannot see the home network.
Windows 7 says that Homegroup requires IPv6, but Verizon Routers don't support this protocol. I have attempted, as noted on the internet, to disable IPv6 on both computers, but this didn't seem to solve the problem. I chatted with an Verizon tech support person who told me no IPv6 routers.
I am looking for suggestions on how to successfully network my computers with Windows 7 and my Verizon router. (Actiontec M1424-WR). We previously tried to put another router in the interface to do wireless and that didn't work.
Thank you.

IPv6 connectivity needs to be enabled on the Windows 7 machines to support HomeGroup networking. Make sure you re-enable those. Once IPv6 is re-enabled, verify that the PCs are at least holding a Link-Local IPv6 address. Open up command prompt and type in "ipconfig" to verify it is holding something, first of all. It's also a good idea to make sure Teredo is in working order as well, as it's considered to be needed in order to use IPv6 on an IPv4 router.
========
The first to bring me 1Gbps Fiber for $30/m wins!

I recently added an extender to my verizon router to be able to connect to apple tv in my guest house. the apple tv message in the guest house says it cannot connect to the server at this time.

I have two problems. Firstly I rented two movies and have not been able to watch them. Error on screen says 'cannot load at this time, try later'. Second problem is that I added a wi-fi extender to my verizon router to connect to apple tv in my guest house. message on screen in guest house says 'cannot connect to server'. I need some set up help.

Hi Kailik Hunter,
Thanks for using Apple Support Communities. This article has some steps you can try if you're unable to sign in to your Apple TV and continue with setup:
Apple TV: Basic troubleshooting
http://support.apple.com/kb/ht1551
If you are still having trouble, you can try to reset your equipment by unplugging Apple TV, your television, your wireless networking equipment or AirPort Base Station, and your router from their power outlet. Wait 30 seconds, then plug everything back in.
Cheers,
- Ari

New Verizon router-'old' HP Photosmart 209a-m

We had to get a new Verizon router - it connected automatically with some of our printers, but not my Photosmart B209a - anybody who can shed light on this problem and give help - much appreciated!!! Can't afford to buy a new printer - computer doesn't recognize router. PLEASE HELP!

Hi norsegal,
I understand you have a Photosmart B209a printer that is not connecting with your new Verizon router. I'm sorry to hear this hasn't been working but I will certainly do my best to assist you in resolving this issue.
Please follow the steps below and you should be able to get your printer back on the network.
1. You will need the USB cable that came with your printer (or any printer USB cable) and the software CD (or the downloaded software)
2. Insert the software CD into the computer and you should get a screen with an option to Connect New Printer or Add a Device
3. Once you've clicked that it should ask you how you're connecting and you will say wireless.
4. The on screen instructions will tell you when to connect the USB cable and when to disconnect it.
5. Once you've followed the steps the information should be updated on your printer and you should be able to print via the wireless connection again.
Hope this helps, have a wonderful day!!
Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
**MissTeriLynn**
I work on behalf of HP

Help with Verizon Router and Setting Up a Second Wireless Router

I had my network set up until I had intermittent loss of the internet. So I received a new Verizon router and I cannot figure out how to use the second wireless router which I used to have working just fine.
The new Verizon router is the Actiontec MI424WR and it is installed in my basement and the signal is weak. However there is a cat5 wire snaked up from the Actiontec router to my home office. Currently that is plugged into the back of my computer for internet acess. My second router is the Trendnet 300Mbps Wireless N Home router. ANd this is the router that I would like to use (and used to use) to trasmit the internet connection throughout the house as well as use for a wired connection to my home security system.
I attempted to plug the cat5 wire from the Actiontec into the back of the Nextrend router (1,2,3,4 and not the WAN) but then would lose the internet signal whether I attempted to log on via wired or wireless. Must be some kind of settings I need to change.
Can anyone help me to understand how to add the second router? I am relatively computer literate but cannot understand the instructions from Verizon. Thanks in advance.
Solved!
Go to Solution.

I point you to http://www.dslreports.com/faq/12506
If you have any questions, please ask.
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Connecting wi fi to a verizon router

how to hook a printer to a verizon router with the lion program

Two different things. Connecting the printer is either with wire, Ethernet cable, or Wireless to the router.
Once the printer is connect to the router then you need to set it up in the computer as a networked Printer.

DMZ on Verizon Router

I have a need to run a Point-to-Point VPN from my work office to my Home Office. For that I’ve enabled DMZ on Verizon Router and point it to my internal NETGEAR Firewall. Then I assigned DDNS Name to my Firewall and created VPN link to my work office firewall. Everything worked like a charm. However, in couple days after that I’ve lost On-Demand option and later whole Chanel Guide. When I call Verizon Support, tech who run diagnostics, told me that my wiring is bad (!). However, when I removed my firewall and reset the router to Factory Default, my Chanel Guide magically reappeared along with On-Demand. Is anybody has an answer for that? Verizon, looks like, does not have a clue.
My Router: MI424WR-GEN2 Firmware: 20.19.8

I connected my NETGEAR Firewall WAN Interface directly to the FiOS Router and my LAN Switch to the firewall LAN Interface. I assigned 172.16.X.1 for my FiOS Router LAN address and 172.16.X.2 for my firewall. Also, I left my internal LAN unchanged and assign default gateway Address to my firewall’s LAN Interface. Then I enabled DMZ on the router and point it to 172.16.X.2.

Replacing verizon router with my own

Hello,
I want to replace my current verizon router with my own, the issue I have is I can not logon. I know I can do a full reset but all the info will be lost. (gateway, verizon password, ect). Is there any way around this? I only have fios, no tv. Incoming connection is a cat 5 cable from fiberoptic converter. Or will I be stuck calling tech support?
Any help would be appreciated, I have small to fair knowledge with these devices.
Geo1cran

since your hooked up with cat5 your good to go. Now if your DHCP verizon would need to help or if your PPPOE then all you have to do is hook up your router and your good to go.

Remote DVR Activation Failure, but I have a Verizon Router!

I keep getting the following message when I try to activate remote programming:
Remote DVR Activation Failure Remote DVR is not supported on non-Verizon routers. Remote DVR service works only with the Verizon supplied routers and with no changes to the original setup. Since you are using your own router and/or firewall setup we cannot enable Remote DVR on your account.
The problem is that I DO have a Verizon router, and I don't know what I can do to enable remote programming. To my knowledge I have not made changes to the original setup....

chrisp wrote:
I keep getting the following message when I try to activate remote programming:
Remote DVR Activation Failure Remote DVR is not supported on non-Verizon routers. Remote DVR service works only with the Verizon supplied routers and with no changes to the original setup. Since you are using your own router and/or firewall setup we cannot enable Remote DVR on your account.
The problem is that I DO have a Verizon router, and I don't know what I can do to enable remote programming. To my knowledge I have not made changes to the original setup....
One of my BIGGEST complaints about ALL the remote features and CID. The router MUST have the correct port forwarding rules in the router, so the web site can find the DVR, or STBs for CID. They never get set right, always get messed up with even the simplest changes to the Verizon router. I gave up on all of it and started using my router that I like better. Even with all the correct port forwarding rules in the router, the features are hit or miss in my opinion. These rules are read only and can only be fixed by Verizon.
Contact tech support and insist that it be fixed while you are on the phone. It can be fixed, and do not take the it will need to be escalated, as an answer. Once I was told it would need to be escalated and could take a couple days. Look at your router, and if it is a REV A. Have it replaced because they are nothing but trouble. If you log into the router you should see forwarding rules for each STB or DVR.

Windows 7/SBS 2003 Networking Issue complicated by Verizon Router

I posted on Answers.Microsoft.com ( http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/windows-7-suddenly-wont-talk-to-sbs-2003-server/e8116774-6b4f-44d3-91cf-b10df236805a?tm=1405553282721 ) and here at TechNet in the Windows 7 IT Pro
forum ( http://social.technet.microsoft.com/Forums/en-US/1f8b8cbc-4b9d-4f68-981c-4c71e7a3f24a/windows-7-suddenly-wont-talk-to-sbs-2003-server-and-viceversa-possibly-dns-but-not-definite?forum=w7itpronetworking ) a problem that I was having with our Windows
7 computers suddenly losing connectivity to our SBS 2003 server. Someone posted an answer (rebooting our router), which worked, but only on a temporary basis. After turning off the router and turning it back on, we get connectivity back for about 3 days, then
we lose it again, and we have to reboot the router again.
I called Verizon, and the tech I spoke to claims that the problem is that the SBS 2003 server should not be the DNS and DHCP server for the network - the Verizon router should be. He's claiming that the fact that we have IP Address Distribution turned off
on their router means that the router never properly knows where each address is assigned. The fact that this all worked up until a week or so ago, and that it's only the Windows 7 machines that are affected, he doesn't have an answer for.
His suggestions were either A) turn off DNS and DHCP on the SBS 2003 server and have both run through the Verizon router, or B) assign static IP addresses to each machine. From what little I know (I inherited this system from someone who left little or nothing
in the way of technical notes) DNS and DHCP have to be running on the SBS 2003 server since it is a domain controller. B) seems possible, as long as I note the static addresses both on the server and on the router.
This still, however, does not really address the underlying issue. Somehow, I think there should be another, easier way to make this work. Especially since, as I said, these Windows 7 machines were content to run for about a year, and only in the past week
or two started having this issue.
Any help would be greatly appreciated.
============== Brian Gerstel Billing and IT Support, Regional Bankruptcy Center of Southeastern PA, P.C.

The LAN is all one subnet (it's not a very big office), a 192.168.1.X network.
I don't think the router's firmware has been updated recently, although I can't swear to what Verizon might have done "behind my back" (they do funny things with some of their routers, from what I can tell),
The router doesn't sit between the server and the clients - it only links our LAN and WAN (there's 1 port on the router hooked to the uplink port of a 16-port Gigabit switch which handles the LAN).
The router is the default gateway for all the systems on the LAN.
When the Windows 7 problem occurs, a Windows XP client can ping a Windows 7 client and vice versa, but a Windows 7 client can't ping the SBS server nor vice versa (and in all cases, I'm pinging numeric IP addresses, not the name). Since the SBS server is
the DNS server, the Windows 7 clients effectively lose the ability to go out on the Internet, although some programs that must cache the data (like Microsoft Outlook) seem to continue working so I think WAN access is still up for them.
Brian Gerstel Billing and IT Support, Regional Bankruptcy Center of Southeastern PA, P.C.

HT3180 My wireless router needed restart. And, no Apple TV signal. How do I reset the Apple TV box.

My wireless router needed restart. And, no Apple TV signal. How do I reset the Apple TV box? no lite. nothing

The remote app requires both to be on the same network and home sharing to be enabled, you will need the physical remote to set this up. You can purchase a replacement through Apple.

Is an AppleTV and Wireless Router Needed for Mirroring Screen?

Is an AppleTV and a Wireless Router Needed for Mirroring from a desktop monitor to an HDTV?

It is one way.
You can also use a mini Display Port to HDMI adapter, and an HDMI cable. A Thunderbolt to HDMI adapter works too.
You might be able to get away with an Apple TV and no WiFi router, if you use an Ethernet cable from the Mac to the Apple TV (never tried it, but it should work in theory).
You may even be able to use an adhoc network with an Apple TV and no WiFi router, but I think the setup would be annoying each time you wanted to mirror and you would give up internt access while the adhoc network was active.

Can't get ip from verizon router to iMac over ethernet

I've got an MI424WR verizon router that is running wireless fine. I also have a Apple Airport Express connected to the Verizon router via ethernet that is running in bridge mode so I can have access to all of my other Apple wireless points and printers in my house. All of this works flawlessly over wireless.
If I plug my iMac into my ethernet cable and then attempt to plug into the back of the Verizon router, I can only get a self assigned IP address on my iMac over ethernet. I've tried many suggestions on the Mac side, from using a manual IP to trashing several prefence files in the system etc. I've also tried a factory reset on the Verizon router. Nothing is working to get the ethernet working to my iMac.
I'm beginning to think it could be a MAC address issue where the Verizon router is not passing or getting something from the iMac correctly, but I have not idea how to really dig into the Verizon router settings to check this out.
Verizon support is less that useless so I'm hoping some savy network folks out there may have some suggestions for me.
thanks for any help you can offer.
Solved!
Go to Solution.

Finally a successfull update.
The crux of my problem was something to do with either the last upgrade to Yosemite or to how my Mac was loading startup items or both of these issues.
First, I confirmed that I could connect to the same ethernet cable with another Mac running one OS back from Yosemite. It connected instantly and the Verizon router passed it an ip address with no problem.
Next, I connected my iMac back to the ethernet and then booted my iMac into safemode and then made a new network location in the network prefs. I then turned off the wifi antennae and had the ethernet set to use DHCP. Renewing the DHCP lease still did not work, but once I rebooted again in safe mode with wifi still turned off, after about 5 minutes, the iMac was able to pull a working ip address from the verizon router.
All on the network side was working fine, but once I booted out of safe mode, my finder went into a horrific crash loop. After doing some cleaning of my system preferences and clearing out all startup items I am now back in business.
thanks to all who suggested ideas.

How can I disable the wireless port (feature) on my Verizon router ?

How can I disable the wireless feature on my Verizon router. I do have 9100EM15-10 Model. I don't know the procedure or what the PW should be. Thanks nss

Thanks. Can we confirm about the router reset procedure. I have 9100EM15-10 Model router. How can I log in to disable the wireless port on my router. I tried calling Verizon tech support but they were difficult to reach or get in last night.

Verizon Router Needed?

Similar Messages

Maybe you are looking for