Version data transferred to during CIF

Hi,
When I transfer my data from R/3 to APO, what version does it get into? Is it only active version 000 or can we assign any version to which it has to go to.
Thanks.

Raj,
In the /SAPOPO/MC8U transaction (create transfer profile) you can assign the R/3 version number for independent requirements, the requirements type, and also mark the transfer as active requirements or not. This should give you the flexibility to send the requirements as needed.
Hope this helps.
Sean

Similar Messages

2012 R2 DPM: massive increase in data transferred during syncronisation of a Deduplicated protected volume

I have been using 2012 R2 DPM to protect a 46 TB 2012 R2 deduplicated volume for the past 4 months without too much issue. The volume is a low access archive server. Current usage on the volume is 23 TB (if not deduplicated, this would be more like 38TB).
Data transferred during a sync (twice daily) is normally in the order of a few 10's of GB. A Restore Point is set for 12am daily.
However, on Saturday during a scheduled sync, it started to transfer very large amounts of data and got to 9TB before failing early this Monday morning ( it had reached the 90% threshold and couldn't increase the replica volume any more). At first I had
thought that
a. There had been a large amount of data suddenly put on the server,
or
b. A lot of files had been changed causing them to be un-deduplicated
However on checking the volume stats ( I have an independent monitoring program), the data usage on the protected volume was fairly static throughout the week at 23 TB - and is still around that now. Besides, nobody generally uses this volume at the weekend.
I am currently running a consistency check on this volume ( this can take 36+ hours), in an attempt to get the sync & restore points working again, however , in the meantime, I need to find out what has caused this.
Has anyone experienced this sort of behavior before ? Where should I start looking ?
DPM version 4.2.1292

Hi,
When was DPM UR5 installed ?
DPM 2012 R2 UR5 (4.2.1292) introduced a fix where long term tape based backups or restores of files that were deduped would fail under the below circumstance.
Backup job for dedupe-enabled volume on Windows 2012 R2 fails. For example, Data Protection Manager backup might fail for following setup:
Data Protection Manager2012 R2 is installed on Windows Server 2012.
Data Protection Manager is protecting a dedupe-enabled volume on Windows Server 2012 R2.
If your DPM Server is running on Windows server 2012 and the protected dedup volume is on Windows server 2012 R2, then after installing UR5, all data will be protected in a non-dedup state. This is necessary because the Windows Dedup filter
on Windows 2012 does not know how to read Windows 2012 R2 dedup data structures which would be the replica volume on the DPM Server.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. Regards, Mike J. [MSFT] This
posting is provided "AS IS" with no warranties, and confers no rights.

How are valid-from and valid-to dates set in TRPROD table in APO during CIF

First question:
How are the valid-from and valid-to dates set in the APO TRPROD table?
For example, if I activate a transportaion lane model on March 1, 2008, will the valid-from and valid-to in TRPROD be 20080301 and 99991231?
Or are these dates defined in the model itself? Or in APO config somewhere?
Next question:
Suppose I rerun the model on May 1 2008 to add some records that didn't get added in the March 1 run. But suppose I want to back-date the valid-from of these records to March 1, rather than use May 1 as the valid-from.
Can this be done?
Or is the valid-from always the date of the CIF that creates the TRPROD records?
Please advise.
Thanks

Hi Srinivas -
Thanks very much for replying so quickly, but your response didn't answer the questions.
Let me try again.
1)
If I run a CIF on March 1 2008 based on a model that will generate APO TLane data, will the TRPROD valid-from and valid-to get automatically set to 20080301 and 99991231?
2)
If the answer to this question is yes, then is it also true that if I run a new set of records in on May 1, 2008 (no duplications with the original set), then the valid-from and valid-to dates will be 20080501 and 99991231.
3)
But if (1) and (2) are both true (if you answer them both "yes", then suppose I want the May 1 record set to have valid-from dates of March 1 (for example, if the May 1 record set includes records that didn't get included in the March 1 set due to an error in selection criteria). How do I get the valid-from to be March 1 when I run the CIF on May 1?
On the other hand, if (1) and (2) are NOT true, then how DO the two dates get set during a CIF ????
Thanks
djh

How to delete Master Data transferred from ECC to APO via CIF

Hi, all
I'm connecting SCM 5.1 with ECC 6.0 via CIF.
When activating Integration Model in ECC, the following error occurred;
"Location 0001 of type 1001 (BSG 592BUSGP) already exists in APO"
This is because Location 0001 was already transferred from different ECC client via CIF, and not cleared.
I'm now trying to initialise master data transferred from ECC to APO via CIF, but in vain.
I suppose I have to first delete all master data CIFed from ECC in APO, or have to execute initialisation of APO master data with ECC data in ECC.
Please tell me how to do this.
For details, please read the followings;
I connected APO client with ECC client 590.
I transferred Plant and Material Master from ECC to APO via CIF.
After that, I wanted to change ECC client from 590 to the other.
I created the other client (592) by client-copying from 590 with SAP_ALL copy profile.
I deactivated Integration Model in ECC 590, and activated the same in ECC 592.
Here, I faced the problem.
The initial data transfer failed due to the duplicate of data.
Now I'm wondering how I can initialise master data in APO and transfer initial data from ECC.
Due to testing purposes, I have to change ECC clients from one to the other this time, but I cannot initialise master data in APO and cannot tansfer initial data from different ECC client.
thanks in advance,
Hozy

Hi all,
Thank you very much indeed for lots of your replies.
Thanks to all of your advices, I'm getting to understand what to do.
Well, I'll say I have to create one more client for testing with other ECC clients or I have to rebuild the client by client-copying from 001 and implementing all transportation requests, for marking del flags to each master data and running del programme sound like tough work, and sound like odd ..
Then, I've got next issue here.
In SCM-APO, I use BI objects, and , if I have to create several clients for testing, I have to set up clients where you can use both BI objects and CIFed master data.
I suppose I have to change 'BWMANDT' in RSADMINA and make RSA1 accessable in other SCM clients and implement tests.
Also, I have to register BI System for newly created SCM clients in RSA1-SourceSystem.
Well, if you have any experiences on this kind of use, and if you have any advice on it, please give me any tips.
Particulary, I'd appreciate very much if you give me advice on which way you have chosen; creating several clients or rebuilding the one client in SCM-APO when you use both BI objects, CIFed master data and Demand Planning.
Thanks in advance.
Hozy

Purchased Content and Data Transfers

I had a few questions regarding purchased content (i.e. apps, music, movies) and data transfers:
1. Can you re-download purchased apps for free or do you have to purchase them again?
2. Can you re-download purchased movies and music if the data is lost or do you have to purchase them again?
3. I noticed every time you download a movie it prompts you to backup the data with discs. I practically never use discs and most of the time, I have a large amount of purchased data that simply will not fit on DVD-Rs. Is it possible to backup data via external hard-drives? Is there an export option in iTunes to do this or do you have to go into the physical path which it's located?
4. Can you sync purchased content with multiple devices? For instance, I have a 32GB iTouch and an iPhone, would I be able to sync the same data for both of these devices or am I restricted to one?
5. How many computers can you have data synced with? For instance, I have five computers and a soon-to-be MacBook. How many computers can I have the same data synced up to?
I tried looking around for this information, but didn't have much luck finding it. Apple doesn't seem to clearly define these parameters unless there is a link one of you might have that discusses these issues. Any assistance would be greatly appreciated.
Message was edited by: chris.chin

Hi, welcome to Apple Discussions.
chris.chin wrote:
I had a few questions regarding purchased content (i.e. apps, music, movies) and data transfers:
1. Can you re-download purchased apps for free or do you have to purchase them again?
Redownload for free, assuming still available in the store.
2. Can you re-download purchased movies and music if the data is lost or do you have to purchase them again?
You are not entitled to a repeat download of any media item. Sometimes unfortunate users are granted a one-time only repeat download if they ask nicely but don't count on it.
3. I noticed every time you download a movie it prompts you to backup the data with discs. I practically never use discs and most of the time, I have a large amount of purchased data that simply will not fit on DVD-Rs. Is it possible to backup data via external hard-drives? Is there an export option in iTunes to do this or do you have to go into the physical path which it's located?
Yes, you can backup to external drives or network shares however iTunes has no system for managing this. You just need to copy the files from their source folders, either manually or....
*Fast backup for iTunes library (Windows Only)*
Grab SyncToy 2.1, a free tool from MS. This can be used to copy your entire iTunes library (& other important data folders) onto another hard drive or network share. You can then use SyncToy periodically to synchronise or echo your library to the backup. A preview will show which files need to be updated giving you a chance to spot unexpected changes and during the run only the new or updated files will be copied saving lots of time. And if your media is all organised below the main iTunes folder then you should also be able to open the backup library on any system running the same version of iTunes.
4. Can you sync purchased content with multiple devices? For instance, I have a 32GB iTouch and an iPhone, would I be able to sync the same data for both of these devices or am I restricted to one?
You can sync the content to as many iPods/iPhones/iPads as you like. Each device can hold protected content from up to five different accounts at any one time.
5. How many computers can you have data synced with? For instance, I have five computers and a soon-to-be MacBook. How many computers can I have the same data synced up to?
You can authorise protected content on up to five different computer systems at any one time. Virtual machines count as separate systems as do computers with reformatted drives or, perhaps, certain hardware changes. Ideally you should deauthorise a computer before any major upgrade. If you are no longer able to access one of your systems but need to release the authorisation then, if you have five active authorisations you can deauthorise all of them together, however you may not then repeat this preocess for 12 months.
Protected content can only be transfered to a device when the computer is authorised. Devices may be manually managed from a number of computers but may only be automatically synced with one. Syncing is a one way process as far as media is concerned, library to device, but certain metadata such as play count and rating flows in both direction. With manual managment such metadata is not copied.
I tried looking around for this information, but didn't have much luck finding it. Apple doesn't seem to clearly define these parameters unless there is a link one of you might have that discusses these issues. Any assistance would be greatly appreciated.
No problem, that's what these forums are for... The information is probably spread around a number of support articles but I don't have the individual links to hand. Feel free to ask if you want more details though.
tt2

Issue in Data transfers using ALE for E-Recruiting standalone system

Dear Experts,
We have an issue in data transfers using ALE. We are having standalone system where E-Recruiting is maintaind seperately and the version is EHP5.
When we configured iDoc in Sandbox and its working fine. But when it comes to Dev and Quality servers this is not working fine.
we have created iDocs using the following filters.
For Object P: Infotypes 0000, 0001, 0002, 0003, 0006, 0024, 0105.
For Objects O,S: 1032, Subtype: 0010
For Object: 1001, Subtype: A003, A008, A012, B007
For Object O: 1001, Subtype: A002, B002, B003, B012, Tyoe of related object: O,S
For Objects: C, O, S, Subtype: 1000, 1002, 1028
For Object:C, Subtype: 1001, Subtype: A007
When we do the data transfers in Sandbox using PFAL it is transferring the data properly.
But when we do the same iin Dev and Quality servers we are not able to do it and gettign 52, 51 errors.
Here we are facing a strange issue. For some Users when we transfer data it is transferring data but with 52 error messgae.
For some users I am getting 51 error where i could not transfer any data.
For some users, when we tranfer O, S, and P related data is moving but getting mostly 52 error and all the relationships are not moving here for O,S and properly. But P related CP, BP and NA are getting created successfully.
It is happening only in Dev and Quality server and that too some users are able to get transferred but not all.
Where will be the issue? How can we resolve this?
Any help will be appreciable.
Thank you in advance.

Hi Sekhar,
Have a look over these threads.
Errors in ALE data transfer to E-Recruiting.
http://scn.sap.com/thread/1535402
BR,
RAM.

Data transfers from SRM to R/3

Hi,
i have follwing questions?
1. How date transfer from SRM to R/3?
2. Why PO transfer throught RFC? why not IDoc? and why confirmation and invoices are transfer using IDOC?.
3. config document for EBP-SUS?
Thanks
Rams

Hi Rams,
The data transfers between SRM using ALE (Application Link Enabling) via RFC & IDOCs...
P.O is transferred to R/3 using RFC. Confirmation and invoice through IDOCs.
Since P.O is the leading document and of course legal document, there should not be any duplication. Means if it generates two P.O numbers one in SRM & the other in R/3 they are considered as two different P.Os.And will be an issue during audit.
Where as confirmation and invoice posting documents are internal documents and the docs created in the back end with the back end number range. In this case same number is not mandatory.
Hope this makes you more clear.
Award points for helpful answers.
Rgds,
Teja

Creation of Transportation lanes during CIF of scheduling agreements.

Hi,
Could anyone please let me know the place(CIF Code) where transportation lanes are created during CIF process of scheduling agreements from R/3 to APO system. This scheduling agreements will be created in R/3 and will CIFed to APO(SPP).
I need to enhance the process where Transportation lanes are created when scheduling agreements are CIFed from R/3 to APO system. The enhancement will be adding a custom planned delivery time value to Means of transport(MOT) of the transportation lane.
I tried debugging the CIF but in vain.
Thanks in advance.

What is the Purchasing Document used - Purchasing Info Records or Contracts? You can CIF any of these to APO to create Procurement Relationships which in turn automatically creates Transportation Lane. You have to assign Means of Transport manually though. Note - T Lanes created with reference to Contract are however not used by SNP for source determination.
The other option is Special Procurement Key - if assigned in Material Master will automatically create TLane in APO when Materials are CIFed. Downside of that process is no control on TLane Validity Date and / or other Planning Parameters like Lot Size / PDT.
As for creation of T Lane based on Source List - SAP Help mentions it can be used but have not seen in any live project so cannot comment.
Hope this helps.
somnath

I have old Macintosh LC that recently passed on, anyone know where I can get this repaired or have the data transferred into something else?

I have an old Macintosh LC that recently went down. I am located in the Portsmouth, NH area.
Anyone know where I can get this repaired or have the data transferred??

How much $$ do you care to spend to transfer the data on the LC's 40 or 80 MB hard drive? The original LC is now 21 years-old and has little if any market value (I know - I have an LC I and an LC III), so professional repair will easily exceed that. It's considered "obsolete" by Apple's authorized repair shops, so parts are not available. Was it starting up normally before it stopped working, and if so, were the date & time always correct after it had been disconnected from an electrical outlet? If not and if startups have been hit or miss for a while, your LC undoubtedly needs a new PRAM battery installed. It's a 3.6-volt ½AA lithium battery and is installed in a black plastic holder w/retainer cover clipped over it on the LC's motherboard. The battery can be purchased at battery specialty retailers for about $8 or less, as well as from a number of online merchants. If you don't mind paying 2-3 times the value of the battery, Radio Shack carries it. If you need directions for installing the battery, post back. It's the least expensive thing to try and a new battery has brought many a dead Mac back from the dead. As for the internal hard drive, it could be removed and installed in a slightly newer, pre-G3 Power Mac having an internal SCSI bus. If there are any thrift stores in your area, you might find a suitable Mac for this purpose. This would involve removal of the hard drive from the LC and installation in the newer Mac, with a slight change in the LC's SCSI address jumper placement. Once installed in the newer Mac, the files could be copied. If this is more challenging than you planned on, you might check your area for a Mac User Group, where you might be able to take your LC and have someone transfer the files for you. After the files have been transferred to another medium, you may have problems trying to open them on a newer Mac running a newer OS version than the LC's (System 7.0, 7.1, 7.5.x, or 7.6), if the programs aren't compatible.

Large data transfers in early morning hours putting me over my data limit

I am getting large data transfers labeled Intranet Media Net from two different Iphones in my home. These transfers occur typically in the early morning hours when we are sleeping and when we should be connected to Wifi. ATT suggested that I turn off the option to send updates to Apple, which I did. However, the charges are still occuring. Last night a 35MB transfer has nearly put my daughter's phone over her 200 MB limit. ATT suggested that I turn off cellular data to eliminate these from occuring, but that seems silly. Plus, who is to say that they won't occur when I turn cellular on, in order to use data when I am outside of a Wifi area? Any help would be much appreciated. I don't know if this is an Apple issue or an ATT issue.

How do you get logs out of a TC anyway?
From the latest one you cannot.. no logs at all so that is the direction Apple is moving.. the black box.. well white box that you feed this into and get that out of.. but all the works inside are complete mystery.. that is the end point.. not quite there yet.
Logs from v5 utility or SNMP.. both still working on any of the earlier TC.
You can install v5 on Mountain Lion.
How to load 5.6 into ML.
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
Leave the package open on the desktop so you can see the file. AirportUtility56.pkg
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. If your Mac refuses to run the software, because it wasn’t downloaded from the Apple store, go to security in preferences and allow other software to work.. this is limitation of trade methinks. You can set back later if you like.
Now drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. in finder, open the new directory, drill down.. applications, utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall version 6 (now 6.3 if you updated) so don't try.. and you cannot or should not run them both at the same time.. although I have had no problems when doing so.
Give 7.6.3 firmware the heave ho.. and use 7.6.1 and if the TC is more than 18months old.. round about .. even a Gen4 you can go back to 7.5.2.. which seems more solid again.
As stated above.. by the time you get early Gen3.. they can have board faults. and earlier ones are especially not reliable with power supply faults.

Data adapter failed during OnLoad: The UDC file contains errors: '=' is an unexpected token. The expected token is ';'.

I am working on SharePoint 2010 Infopath form, i have created one secondary connection to SharePoint List view using XML Connection it works fine.
For the deployment from DEV to PROD i converted this connection to universal data connection (UDC) and tested this before deploying to PROD but i m getting below error.
An error occurred querying a data source.
i checked ULS logs and found below details
Data adapter failed during OnLoad: The UDC file contains errors: '=' is an unexpected token. The expected token is ';'. Line 17, position 108.
UDC file is below
<?xml version="1.0" encoding="UTF-8"?>
<?MicrosoftWindowsSharePointServices ContentTypeID="0x010100B4CBD48E029A4ad8B62CB0E41868F2B0"?>
<udc:DataSource MajorVersion="2" MinorVersion="0" xmlns:udc="http://schemas.microsoft.com/office/infopath/2006/udc">
<udc:Name>LastItemID</udc:Name>
<udc:Description>Format: UDC V2; Connection Type: XmlQuery; Purpose: ReadOnly; Generated by Microsoft InfoPath 2010 on 2014-04-25 at 16:49:31 by DOMAIN\username.</udc:Description>
<udc:Type MajorVersion="2" MinorVersion="0" Type="XmlQuery">
<udc:SubType MajorVersion="0" MinorVersion="0" Type=""/>
</udc:Type>
<udc:ConnectionInfo Purpose="ReadOnly" AltDataSource="">
<udc:WsdlUrl/>
<udc:SelectCommand>
<udc:ListId/>
<udc:WebUrl/>
<udc:ConnectionString/>
<udc:ServiceUrl UseFormsServiceProxy="false"/>
<udc:SoapAction/>
<udc:Query>https://contoso/_vti_bin/owssvr.dll?Cmd=Display&List={32364DED-7FE3-4276-837C-F2AC62C04B81}&View={804CC528-34B2-4473-89DB-C4E766CACC95}&XMLDATA=TRUE&NOREDIRECT=TRUE</udc:Query>
</udc:SelectCommand>
<udc:UpdateCommand>
<udc:ServiceUrl UseFormsServiceProxy="false"/>
<udc:SoapAction/>
<udc:Submit/>
<udc:FileName>Specify a filename or formula</udc:FileName>
<udc:FolderName AllowOverwrite=""/>
</udc:UpdateCommand>

</udc:ConnectionInfo>
</udc:DataSource>
w: sandippatilblog.blogspot.com/

Hi Sandip ,
How about escape “&” to “&” as below:
<udc:Query>https://contoso/_vti_bin/owssvr.dll?Cmd=Display&List={32364DED-7FE3-4276-837C-F2AC62C04B81}&View={804CC528-34B2-4473-89DB-C4E766CACC95}&XMLDATA=TRUE&NOREDIRECT=TRUE</udc:Query>
Reference:
http://social.technet.microsoft.com/Forums/en-US/534fae6b-2cef-4947-86e2-4869cb291cfe/the-form-cannot-be-opened-because-it-requires-the-domain-permission-level-log-id-5566-error?forum=sharepointcustomizationlegacy
http://stackoverflow.com/questions/3493405/do-i-really-need-to-encode-as-amp
Best Regards,
Eric
Eric Tao
TechNet Community Support

Getting data transfered from old HD to new ones, leaving 2 slots filled . .

Hello,
*(Below is a thread I started in another forum, but, didn't get my final questions answered (see at bottom of this post in BOLD), and am hoping for further help and suggestions. I know there is a lot to read here, but, I think this information will help other novices, such as myself. Thanks!)*
I have 2 new HDs (each 1T) uninstalled, and I have my old HD (160 gigs) currently residing in one of the two slots in my G5. Any ideas on the best way/process to get the data transfered from the old HD to the new ones, leaving my two slots filled with the 2 new drives AND my data from the old HD transfered and intact, with a RAID0 setup?
OR, are there any other suggestions on a good setup with the 2 new HDs??
I'm open to suggestions.
I always back-up on external HDs, so, is their a need for me to worry about setting up a RAID0??
I'm doing video processing for DVD release.
Should I just max out the 2x1T gig HDs and not worry about a HD failure??
All Suggestions welcomed!!
Thanks, Jack
*FROM THE CUTTERMAN:*
You are limited with only 2 drive slots. In this scenario what usually works best is a small fast drive (eg Velocirapter or SSD) for OSX/Applications and a large drive for video files. It is not advisable to have the operating system running from a striped array.
Since you already have the drives, here is what you can do.
Install one new drive and format the partition you wish to use for OSX. You may not want to use the whole drive for OSX, so make 2 partitions. Be sure that it is GPT-formatted so it can boot.
Use CarbonCopy Cloner to copy your current OSX partition to the new one.
Set the startup disk as the new partition.
Remove the old drive and replace it with the second new one.
Reboot, and partition/format new drive.
*Hey Cutterman,*
Thanks for the advice. That sounds like a good set-up. I'll have to research the process of doing what you've advised, but, should work out ok:
A. Install one new drive and format the partition you wish to use for OSX. You may not want to use the whole drive for OSX, so make 2 partitions:
1. Partitions are done under Disc Utilities correct? Never done it before; will take a look.
B. Be sure that it is GPT-formatted so it can boot.
2. GPT is also done under Disc Utilities, correct? Here I start to get a bit confused, as I've formatted Extended Journal, SO, the partition with the OSX & Applications is formatted GPT, and the rest of the HD is formatted as Extended Journal?
C. Use CarbonCopy Cloner to copy your current OSX partition to the new one.
3. So, I partition the first new HD and use Carbon Copy Cloner (also under Disc Utilities) to copy the OSX & Applications from my original HD to the first new HD, correct?
D. Set the startup disk as the new partition.
4. This will be an option when I setup the partition???
E. Remove the old drive and replace it with the second new one.
F. Reboot, and partition/format new drive.
5. QUESTION: So, you recommend not striping the HDs: If I do a RAID 1, which sets up a mirror of the HDs, and since the first new HD is partitioned with the OSX & Applications, AND is set up as the Startup Disk, then the second new HD will also mirror that?? Another QUESTION: Even if the second new HD does not mirror the OSX & Applications, the second HD will only mirror the space/partition not utilized by the OSX & Applications partition, correct?
Thanks for your help!!
Jack
*FROM THE CUTTERMAN:*
OK I will try to answer your questions. To begin, if you want to mirror the 2 drives then you will need to boot from the SL install DVD or an external (USB/firewire) drive to set it up. IMO for your purposes it is too much hassle and a waste of HD space.
1) Yes partitions are created in Disk Utility
2) Yes, you choose a volume Scheme (ie number of partitions) and size them by dragging the separator bar. Then select the planned boot partition and click Options..., then choose GPT. I think it is usually the default but check and make sure. Extended journaled is the usual format.
3) You need to download Carbon Copy. It is a free tool that will copy the entire image of your current system partition to the new one and make it bootable. Consider making a donation as it is a very useful and frequently updated utility. It is fairly intuitive to use. You can also use the restore feature in Disk Utility but I have had more experience with Carbon Copy.
4) Once the copy process is finished the new boot partition will show up under the startup disk selections (this tool is in System Preferences).
*FROM 666Sheep:*
If may i correct one thing: OP, don't choose GPT (GUID Partition Table). You got PPC Mac (G5), so valid partition type for you is Apple Partition Map (APM).
GPT is for Intel Macs and you will not able to boot from this kind of partition.
*FROM THE CUTTERMAN:*
Thanks for the correction- my bad. No familiarity with non-Intel Macs.
G5 PowerMac, 2.5 GHz Dual, Dec. 2004, 6.5 GB RAM, 149 GB HD
*Hi All,*
*Since this process will come to a head on Tuesday/Wednesday, and I hope to be successful in transferring Old HD data to new HD/s.*
*A: I'm still a little foggy here, as I thought I'd set up the 2 new T-gig HDs so that if one of them failed, I'd still have the data backed up on the other HD; more ideas concerning this would be reassuring:*
*WHAT DOES "IMO" mean?*
*(IMO for your purposes it is too much hassle and a waste of HD space.)*
*As I understand the points made: After I partition the first new HD, and Carbon Copy data from old HD, I then install second new HD, and this will just act as an overflow from the first partitioned HD, correct? Because, if set up a Raid1/Mirror, the OSX partitioned portion of the first new HD will not copy to the second new HD, and that space on the second new HD will be wasted, correct?*
*Also: I have to set up RAID1 (if I do not set up RAID0), correct?*
*RAID 1*
*From WIKI: RAID 1 mirrors the contents of the disks, making a form of 1:1 ratio real time mirroring. The contents of each disk in the array are identical to that of every other disk in the array. A RAID 1 array requires a minimum of two drives.*
*Carbon Copy is a free tool that will copy the entire image of your current system partition to the new one and make it bootable.*
*1. Is my old HD partitioned? Is that done automatically by MAC prior to PC purchase?*
*2. Do I Carbon Copy the whole old HD or just parts? (eg. OSX, Photo Shop, After Effects, Various Files)*
*3. I read that it is necessary to DEACTIVATE Photo Shop (I have CS3) prior to doing Carbon Copy. Is that correct? If so, does this also apply to other Adobe applications? Such as After Affects, Illustrator??*
*Thanks to all for the help!!*
*G5 PowerMac, 2.5 GHz Dual, Dec. 2004, 6.5 GB RAM, 149 GB HD*

Confusing Information:
A1: You also want to make sure the drive you are backing up to is formatted Mac HFS Extended (HFS+) if using Mac OS 8.1 or above.
A2: On PowerPC Macs, your clone should be partitioned as Apple Partition Map.
*Q? I thought the new HD (1T) should be formatted in Extended Journaled?*
B: Also disable Spotlight (in 10.4 only) on your destination drive using Apple menu -> System Preferences -> Spotlight -> Privacy to add the destination drive to the pane.
*Q? I'm using 10.4.11, so, I should follow these instructions?*
C: If possible, boot into safe mode to perform the backup (holding the SHIFT key at startup). In addition, you can clone while logged into another administrative user that you don't use at all to avoid further complications of changes which may be happening to your regular user (though don't use Fast User Switching to get into that other user, since that other user is still active when fast user switching is used). Otherwise you are going to be running a backup on a live system which could have changes happening while you are attempting to backup. These may yield an imperfect clone, with uncertain success at recovery. It may be possible that your clone will have its own hardware issues, so make at least two copies.
*Q? ?????????????*
*I GOT THE ABOVE INFO. FROM THE FOLLOWING SITE:*
Making a clone/mirror/duplicate backup
http://www.macmaps.com/backup.html#SHORTANDEASY
*ALSO, WHAT DO YOU THINK ABOUT THE ADVICE ON THIS PAGE:*
http://www.levoltz.com/2010/04/21/how-to-transfer-data-to-your-new-hard-drive/

No data in IT0007 during the period 05.05.2010 - 31.05.2010

Hi experts,
When i am running PY simulation for a particular employee who has joined as trainee a year before and was confirmed on 05.05.2011 I am getting error in log saying No data in IT0007 during the period 05.05.2010 to 31.05.2010. Pls brief me to overcome this issue ASAP.
Thanks in advance
Upensap

Please go to PA30 select the IT0007 and go for overview
check the start date of the records, check if there is data for the mentioned period in the error?
if not maintain it .
from which date the employees payroll is going to start?

I just bought a new desktop and will be taking my old one to the apple store tomorrow to have the data transferred. Does the transfer include the transfer of programs or just data?

I just bought a new desktop and will be taking my old one to the apple store tomorrow to have the data transferred. Does the transfer include the transfer of programs or just data?

They will simply use Migration Assistant to transfer your Home folder, third-party applications and support files, and system preferences. This is something you could do yourself. You would need a Firewire cable to connect between your old computer and your new one. Migration Assistant is installed in the Utilities folder of your new computer.
See Transferring files between two computers using FireWire and How to use Migration Assistant to transfer files from another Mac.

What happens to versions data when files are deleted ?

When working on a document with an application using autosave, I understand modifications are regularly saved together with the actual state of the file. When such file is dulicated, history and the different versions are not duplicated.
My question is, what happens to the versions data if the original file is deleted and is the space used for all versions reclaimed ?
Working with big documents on SSD disk could be a problem seems to me.
Thanks for your comments.

Hi Tony,
As soon as data is deleted from the cube, Data will not be available for reporting. because for any reports data is fetched from Tables, for DSO they will fetch from Active table.
So you will receive a message Data not found, if the data is deleted from Cube's table.
Assign some points, if this is helpful.
Rgs,
I.R.K

Version data transferred to during CIF

Similar Messages

Maybe you are looking for