VoIP Setup between two centers

Dear Friends,Please help me out for connectivity of voice. We have two Centers in a distance of 2Km. We have connected both centers with Bridges of 2Mb Backbone for data transfer.we have PBXs in both centers. In both centers we have the staff of 50 members each. What is the best possible way for the connectivity of Voice. what type of equipment will support this. Please refer the equipment & Configuration details, So that i am very thankful to you.
Regards
M.K

Hi, you can see the document:
http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a0080080b60.html
At "figure 5" you can find an example of linking two PBXs. The diagram you can see here can be useful to your own design, but instead using E&M interfaces you can use BRI or PRI, depends on what interfaces you can use at your PBXs and how many simultaneous calls you want.
Supposing you have BRI interfaces and you want four simultaneous calls you could use a cisco2801 with a VIC2-2BRI-NT/TE and the DSPs needed (depends on the codec you're going to use with your calls).
Regards

Similar Messages

How can a session be setup between two MacBook Pro's at different locations on high speed Internet connections, be setup to have a live recording session in Logic?

My partner and I live on opposite sides of the valley here in Phoenix. About 50 miles apart one way. We are Musicians and are working on a commercial for television, and would like to know if there is a way, between FaceTime and Logic, that we can configure our MacBook Pro's to record sessions together without having to be at the same house? When we FaceTime, he can hear my keyboard through his headphones, but we can't seem to get the signal routed into Logic and register to a track when its record enabled. Is there a way for us to save gas, and record at seperate locations, so he can engineer me and I can engineer him, while we build this project in Logic and Final Cut? Here is what we are using, we have nearly identicle setups, which was planned so we might be able to do something like this. Both of us are using Mid 2012 15" MacBook Pro's with 2.6GHz Intel i7 processors and 16GB RAM. The only difference between the two MacBooks is that his has an Optical Drive, but I removed mine and replaced it with a 2nd SSD Drive, so I have two Samsung 840 Pro's each with 512GB in my MacBook Pro. His just has one Samsung 840 Pro with 512GB. We both use Focusrite Saffire Liquid 56 Firewire Audio Interfaces, and we both use Logic Studio 9 Academic. I don't know if you need to know what we are using in order to help us figure out how to configure the MacBooks for a live session, so I figured I would give you those details just in case. If you need any more information, just let me know? Oh, we both have high speed cable Internet connections. Mine is 150Mbps speed which is the absolute fastest I can get in my area. And his is only a 50Mbps speed line.
Again, what we are looking to do is have a LIVE recording session, in Logic, with him at his house and me at my house. When we FaceTime each other, we can pretty much hear each others keyboards as if they were part of the conversation, and as crystal clear as we can hear our own when recording, but we can't seem to record enable an Audio track in Logic and route that keyboard signal into Logic and record it so we can engineer each other without either one of us having to drive to the others house, to be there to do it. If any of this even makes sense, I'm not quite sure how to better explain it. So hopefully you get what I mean, otherwise just say so, and I will try to do a better job explaining it. :-)
Anyone who can help us with this little problem would be greatly appreciated, and quite a hero in these two humble Musicians Worlds!! So from both of us, THANK YOU in advance for any input you might be able to give us. I look forward to hearing any and all suggestions.
Scott

Hey Scott
You and ALOT of people are attempting to do this, myself included.
Unfortunately at this point (to my knowledge) it's a pretty CRAP setup involved that will likely leave you frustrated.
HOWEVER:
A few things CAN be done:
IF you are getting live audio from your partner over the internet, you can re-direct that audio directly into Logic using a program called SoundFlower.
There are a few alternatives to SoundFlower, like JackTrip, and.....(the name eludes me)
(SoundFlower is from a company called Cyling 74 who also makes Max MSP. )
Once in Logic, you set your audio inputs to the track to be Soundflower. (either 16 inputs, or in this case 2)
That all being said, regardless to speed, you are still going to experience latency in the connection, and THAT is the part that will likely drive you to the mad house.
THIS all being said, I believe there are websites out there that are set up to actually do this kind of thing, (at least there WERE) but likely membership costs, and other "hidden" problems that you only learn about after you have signed on the dotted line. (Hopefully I am wrong?)
If you don't need to do a "live jam", there are always solutions like DropBox that work very well for exchanging large files quickly.
If you want to record live MIDI input from his keyboard, I am unaware of any solutions for this.
Due to the popularity of the iPad, you might want to look into the App store, and see if there is something available.
Good luck!
Treatment

Requirements about delay and bandwith for using OTV in Nexus 7000 between two data centers separated 25 miles?

We have two Nexus 7000, and I need use them with OTV between two data Centers separated 25 miles, but I don´t know what are the optimal values about bandwidth and delay (ms) for extended VLANs IDs (production and DAG replication) for Microsoft Exchange environment. Can somebody tell me please which are the values required for operate OTV in optimal conditions in this case? We have about 35 000 users that will use that platform of email. Thanks a lot for your comments. Regards.

We have two Nexus 7000, and I need use them with OTV between two data Centers separated 25 miles, but I don´t know what are the optimal values about bandwidth and delay (ms) for extended VLANs IDs (production and DAG replication) for Microsoft Exchange environment. Can somebody tell me please which are the values required for operate OTV in optimal conditions in this case? We have about 35 000 users that will use that platform of email. Thanks a lot for your comments. Regards.

Tried to setup Shared between two MacBooks, now cannot login to either

I tried to setup a sharing folder between two MacBooks at home, both have Snow Leopard and with the latest software update, but when I turned off both MacBooks then turned them back on, it will not go pass the white Apple screen showing it's processing, but does not go to the login screen.
What can I do to login back into my MacBooks?
Thanks
-Erica

Ok, I don't follow that.
You selected the Hard Drive and Get Info.
Now, did you click the Shared Folder check box, or did you go to Sharing and Permissons and make changes?
changed the shared settings to a folder on both MacBooks
There is no ability to change settings to a folder from the Get Info panel. You can add a user and give them specific access, or change the current user's access rights, but not indicate a folder.

Create line extension between two SPA-3102

I`m having problems to create a line extension between two SPA-3102
I have one SPA-3102 connected to an analog PBX system with IP 192.168.0.201, and the other SPA-3102 with analog phone and IP 192.168.0.200
I succesfully setup them to make a call from the first to the second
But I couldn`t setup them to make a call from the second (192.168.0.200) and give me the dialtone of the PBX connected to the first SPA-3102 (192.168.0.201).
I could setup a hot line on the second SPA-3102 (192.168.0.200) and call to 192.168.0.201, but it doesn`t take the line to hear the pstn dialtone.
I saw many answers about this problem, but no one resolve the problem, i have the latest firmware. please, anyone could help me and if it`s possible to work please send me all the configuration needed.
Thanks again

Hi Jeremy,
I have a similar problem, I have one PSTN line (say Line1) with free minutes to mobiles, so its good for outgoing calls. The other line (say Line2) which i have is acually VoIP but it comes with its own hardware (magicJack if you have heard) so I can't use a SIP client and have to use the supplied Hw client, but it does give me an option to connect any normal phone to this magicJack (i suppose that would make it a fxs port). Now this magicJack is cheap for other people to call me.
I want to find a solution so that all the calls I receive on Line2 get forwarded to my mobile number via Line1. And if I receive any calls on Line1 they should be treated normally (my home phone rings). Do you have some idea how I can achieve this with minimal spend? Thanx
Atif

Using A FireWire cable between two Macs and Migration Assistance to transfer all my desktop to my macbook laptop, will all my apps, bookmarks, contacts and files be transferred? I am trying to make a complete copy of my desktop to my laptop.

Using a FireWire cable between two Macs and the Migration Assistance feature, will al my apps, bookmarks, contacts and files be tranferred?

See Pondini's Setup New Mac guide

Site to Site VPN Between Two ASA 5505's Up But Not Passing Traffic

hello,
i am setting up a site to site vpn between two asa 5505's. the tunnel is up but i cannot get it to pass traffic and i have run out of ideas at this point. i am on site as i am posting this question and only have about 4 hours left to figure this out, so any help asap is greatly appreciated. i'll post the configs below along with the output of sh crypto isakmp sa and sh ipsec sa.
FYI the asa's are different versions, one is 9.2 the other is 8.2
Note: 1.1.1.1 = public ip for Site A 2.2.2.2 = public ip for site B
Site A running config:
Result of the command: "sh run"
: Saved
ASA Version 8.2(2)
hostname csol-asa
enable password WI19w3dXj6ANP8c6 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 192.168.1.0 san_antonio_inside
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 1.1.1.1 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns domain-lookup inside
dns server-group DefaultDNS
name-server 24.93.41.125
name-server 24.93.41.126
object-group network NETWORK_OBJ_192.168.2.0_24
access-list inside_access_out extended permit ip any any
access-list outside_access_out extended permit ip any any
access-list outside_access_in extended permit icmp any any
access-list outside_access_in_1 extended permit icmp any interface outside
access-list outside_access_in_1 extended permit tcp any interface outside eq pop3
access-list outside_access_in_1 extended permit tcp any interface outside eq 8100
access-list outside_access_in_1 extended permit udp any interface outside eq 8100
access-list outside_access_in_1 extended permit udp any interface outside eq 1025
access-list outside_access_in_1 extended permit tcp any interface outside eq 1025
access-list outside_access_in_1 extended permit tcp any interface outside eq 5020
access-list outside_access_in_1 extended permit tcp any interface outside eq 8080
access-list outside_access_in_1 extended permit tcp any interface outside eq www
access-list outside_access_in_1 extended permit ip san_antonio_inside 255.255.255.0 any
access-list outside_1_cryptomap extended permit ip 192.168.2.0 255.255.255.0 host san_antonio_inside
access-list outside_1_cryptomap_1 extended permit ip 192.168.2.0 255.255.255.0 san_antonio_inside 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.255.0 san_antonio_inside 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat-control
global (inside) 2 interface
global (outside) 101 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 101 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface pop3 192.168.2.249 pop3 netmask 255.255.255.255
static (inside,outside) tcp interface 8100 192.168.2.161 8100 netmask 255.255.255.255
static (inside,outside) udp interface 8100 192.168.2.161 8100 netmask 255.255.255.255
static (inside,outside) udp interface 1025 192.168.2.161 1025 netmask 255.255.255.255
static (inside,outside) tcp interface 5020 192.168.2.8 5020 netmask 255.255.255.255
static (inside,outside) tcp interface 8080 192.168.2.251 8080 netmask 255.255.255.255
static (inside,inside) tcp interface www 192.168.2.8 www netmask 255.255.255.255
static (inside,outside) tcp interface 1025 192.168.2.161 1025 netmask 255.255.255.255
access-group inside_access_out out interface inside
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 1.1.1.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.2.0 255.255.255.0 inside
http 2.2.2.2 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map1 1 match address outside_1_cryptomap_1
crypto map outside_map1 1 set peer 2.2.2.2
crypto map outside_map1 1 set transform-set ESP-3DES-SHA
crypto map outside_map1 interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.30-192.168.2.155 inside
dhcpd dns 24.93.41.125 24.93.41.126 interface inside
dhcpd domain corporatesolutionsfw.local interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
anyconnect-essentials
group-policy DfltGrpPolicy attributes
tunnel-group 2.2.2.2 type ipsec-l2l
tunnel-group 2.2.2.2 ipsec-attributes
pre-shared-key *****
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:021cf43a4211a99232849372c380dda2
: end
Site A sh crypto isakmp sa:
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: 2.2.2.2
Type : L2L Role : responder
Rekey : no State : MM_ACTIVE
Site A sh ipsec sa:
Result of the command: "sh ipsec sa"
interface: outside
Crypto map tag: outside_map1, seq num: 1, local addr: 1.1.1.1
access-list outside_1_cryptomap_1 extended permit ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0
local ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (san_antonio_inside/255.255.255.0/0/0)
current_peer: 2.2.2.2
#pkts encaps: 1, #pkts encrypt: 1, #pkts digest: 1
#pkts decaps: 239, #pkts decrypt: 239, #pkts verify: 239
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 1, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 1.1.1.1, remote crypto endpt.: 71.40.110.179
path mtu 1500, ipsec overhead 58, media mtu 1500
current outbound spi: C1074C40
current inbound spi : B21273A9
inbound esp sas:
spi: 0xB21273A9 (2987553705)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, }
slot: 0, conn_id: 1691648, crypto-map: outside_map1
sa timing: remaining key lifetime (kB/sec): (3914989/27694)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0xC1074C40 (3238480960)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, }
slot: 0, conn_id: 1691648, crypto-map: outside_map1
sa timing: remaining key lifetime (kB/sec): (3914999/27694)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
Site B running config:
Result of the command: "sh run"
: Saved
: Serial Number: JMX184640WY
: Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz
ASA Version 9.2(2)4
hostname CSOLSAASA
enable password WI19w3dXj6ANP8c6 encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 2.2.2.2 255.255.255.248
ftp mode passive
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network mcallen_network
subnet 192.168.2.0 255.255.255.0
access-list outside_cryptomap extended permit ip object NETWORK_OBJ_192.168.1.0_24 object mcallen_network
access-list outside_access_in extended permit ip object mcallen_network 192.168.1.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-731-101.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static mcallen_network mcallen_network no-proxy-arp route-lookup
nat (inside,outside) after-auto source dynamic any interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 2.2.2.2 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto map outside_map3 1 match address outside_cryptomap
crypto map outside_map3 1 set peer 1.1.1.1
crypto map outside_map3 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map3 interface outside
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh stricthostkeycheck
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd address 192.168.1.200-192.168.1.250 inside
dhcpd dns 24.93.41.125 24.93.41.126 interface inside
dhcpd domain CSOLSA.LOCAL interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
anyconnect-essentials
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol ikev1
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 ipsec-attributes
ikev1 pre-shared-key *****
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:4e058021a6e84ac7956dca0e5a143b8d
: end
Site B sh crypto isakmp sa:
Result of the command: "sh crypto isakmp sa"
IKEv1 SAs:
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: 1.1.1.1
Type : L2L Role : initiator
Rekey : no State : MM_ACTIVE
There are no IKEv2 SAs
Site B sh ipsec sa:
Result of the command: "sh ipsec sa"
interface: outside
Crypto map tag: outside_map3, seq num: 1, local addr: 71.40.110.179
access-list outside_cryptomap extended permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
local ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0)
current_peer: 1.1.1.1
#pkts encaps: 286, #pkts encrypt: 286, #pkts digest: 286
#pkts decaps: 1, #pkts decrypt: 1, #pkts verify: 1
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 286, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#TFC rcvd: 0, #TFC sent: 0
#Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 2.2.2.2/0, remote crypto endpt.: 1.1.1.1/0
path mtu 1500, ipsec overhead 58(36), media mtu 1500
PMTU time remaining (sec): 0, DF policy: copy-df
ICMP error validation: disabled, TFC packets: disabled
current outbound spi: B21273A9
current inbound spi : C1074C40
inbound esp sas:
spi: 0xC1074C40 (3238480960)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, IKEv1, }
slot: 0, conn_id: 28672, crypto-map: outside_map3
sa timing: remaining key lifetime (kB/sec): (4373999/27456)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000003
outbound esp sas:
spi: 0xB21273A9 (2987553705)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, IKEv1, }
slot: 0, conn_id: 28672, crypto-map: outside_map3
sa timing: remaining key lifetime (kB/sec): (4373987/27456)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001

Hi Keegan,
Your tunnel is up and encrypting traffic one way, the other end is not able to encrypt the traffic.
I would suggest to do a 'clear xlate'? Sometimes if you setup the nonat configuration after you've attempted other configurations, you need to 'clear xlate' before the previous NAT configuration is cleared and the new one works.
HTH
"Please rate useful posts"

Transfer VOIP Calls Between Cisco Desk Phone and Cisco Jabber For IPhone 9.5

Does anyone know how to transfer an active voip call from a Cisco IP Desk Phone to Cisco Jabber for IPhone? I can transfer a call from Cisco Jabber for IPhone to my Cisco IP Desk Phone no problem. I put the call on hold and then click "Resume" on my Cisco IP Desk Phone. However I cannot do the same but the other way around. If I put the call on hold on my Cisco IP Desk Phone, I see "no active call" on my Jabber client. The only information I could find slighlty relevant was using the Mobility Key/Remote Destination Profile feature however this defeats the object as this will forward to an external number, e.g. mobile and I just want to transfer the call within the VOIP environment between the two devices that are using the same directory number.
I am using Cisco Call Manager 9.1(2), Cisco Presence 9.1 and Cisco Jabber for IPhone 9.5.
Any help would be greatly appreciated.
Kind Regards,
Paul Parker.

Did you ever find an answer to this ?
I am seeing the same behavior and trying so see if I can put calls on hold and pick them up both ways also.
The only answer I seem to have found is to use park instead
That would/should work but I would just prefer to hold/unhold
Just not sure why we would not be able to hold/unhold on what is essentially a "shared" line
Does anyone have this working for them ?

Communication between Two WebLogic instances on the same machine

Hi,
We're having a problem with communication between two copies of Weblogic on
the same machine. They are configured with seperate ports (regular and SSL).
Independantly, they run fine. I can access EJBs running on either of them.
The problem is that a bean in one of them has code which attempts to access
an EJB on the other one. The procude fails when trying to obtain the initial
context. This same code works if compilied independantly of WebLogic on the
same machine.
Are there any known issues regards communication between two running
instances of Weblogic on the same machine?
Thanks in advance,
Randy Yarger
marchFIRST
[email protected]

Thanks for the prompt reply.
There is one IP address (internal address 10.227.1.34) one the machine. WLS1
is set up at ports 7001 and 5133. WLS2 is setup at ports 7004 and 7005.
When WLS1 attempts to obtain a context to WLS2 with the URL
t3://10.227.1.34:7004/ it pauses for a long period of time. Running truss
on the both WLS processes shows communication occuring between the two
followed by long periods of silence. Finally WLS2 spits out the error
ConnectionException[7001,7001,5133,5133,7001,7001] (paraphrased, I can get
the entire error if it would help).
After another long pause, WLS1 quits trying with the error 'Server
10.227.1.34:7004 not found' (again paraphrased).
Among the things we've tried:
* Changing the URL from the IP to 127.0.0.1
* Enabling/disabling SSL on either or both WLSs.
* Changing the server name in WLS2's copy of weblogic.properties from
'myserver' to 'myserver2' (previously they were both 'myserver')
* Upgrading WLS2 to 5.1.0sp5 (Tried upgrading WLS1, but was getting class
not found errors and quit because that WLS is being used by other people)
This is a Solaris server. WLS1 is running 5.1.0 and WLS2 is running 5.1.0sp5
Any suggestions would be appreciated.
Best,
Randy Yarger
marchFIRST
[email protected]
"Michael Girdley" <[email protected]> wrote in message
news:[email protected]...
>
>
There should not be. What is your network configuration? Are they on
separate IP addresses?
Thanks,
Michael
Michael Girdley
BEA Systems Inc
"Randy Jay Yarger" <[email protected]> wrote in message
news:[email protected]...
Hi,
We're having a problem with communication between two copies of Weblogicon
the same machine. They are configured with seperate ports (regular andSSL).
Independantly, they run fine. I can access EJBs running on either of
them.
The problem is that a bean in one of them has code which attempts toaccess
an EJB on the other one. The procude fails when trying to obtain theinitial
context. This same code works if compilied independantly of WebLogic onthe
same machine.
Are there any known issues regards communication between two running
instances of Weblogic on the same machine?
Thanks in advance,
Randy Yarger
marchFIRST
[email protected]

Configuring SMTP Namespace Sharing between two Exchange Forests on the same LAN

Hi guys, really hoping that someone can help me with configuring SMTP Namespace Sharing between two Exchange Forests on the same LAN.
Basically, I have created a new forest and installed a new exchange organisation in this forest. Both forests are located on the same IP subnet and a two way trust has been created between the forests. Federated sharing has also been configured.
I can use ADMT to migrate the user and computer accounts to the new forest and also migrate test mailboxes over. Ideally, I want to be able to do the mailbox migrations in stages so will need to be able to have mail flowing between the two forests.
I have read over the following article (http://ibrahimnore.wordpress.com/2012/09/06/configuring-smtp-namespace-sharing-between-two-exchange-forests-part-2/)
which is good but it's demonstrating over the internet, can anybody advise how this can be achieved on the local LAN?
Any help greatly appreciated :-)

Hi Gilliano,
Thanks for correct link. I must say this is a very good article indeed, I read the entire article and if you go to the 3rd part of this article, please note the text "DOMAINC.COM is configured as Internal Relay Accepted Domain on both the domains"
This is exactly what I asked you to check. Personally, I understand the method described in this article will work but its very complex to manage and administer, while the easiest option is to configure internal relay at the first place and no need to make
so many DNS changes and customizations to your environment.
The solution really depends on what your requirement is - Since you mentioned that you are migrating stuff over from source to destination - I feel this article is too complex for your situation and not really worth (for your requirement). The setup described
in the article is an excellent choice if you are planning to keep both forests alive for longer duration due to several reasons like compliance or company mergers and so on...
please let me know if my explanation is not clear enough.. we can even even have a one-on-one email conversation too!
All the best!
Please mark as helpful if you find my contribution useful or as an answer if it does answer your question. Regards, Siva

Display of internal revenues between profit centers in FI (FAGLL03)

Hi,
I need to do transfer posting ( Storage location to Storage Location ) between two profit centers which are in the same plant. I need to have the line item to display the internal revenue to the sender profit center and cost to the receiving profit center.
I maintained accounts for the mapping of internal goods movements between profit centers (Transaction 0KEK "Account Determination for Internal Goods Movements"). But the additional line items are not reflected.
Thanks
Bhaskar

Hi ,
This requirement is achieved through configuration.
Thanks

I want to create serial communicatios between two notebooks via Bluetooth

Hi,
I'm trying to accomplish serial communications between two laptops via a Bluetooth connection.
The two laptops are NOT Toshiba notebook, but they are both running the Toshiba Bluetooth Stack For Windows. They are also both using the default Bluetooth Manager program that is supplied by Toshiba and Dell (just rebadged?).
Basically I can set up a connection no problems, but then I send serial data from one computer and watch the receiving serial port on the other computer but nothing ever arrives.
Are there any good tutorials for this? It would be nice to have something for the Toshiba Bluetooth Manager in particular as the windows and buttons will have the names as explained in the tutorial.
Thanks in advance.
Adam

I tried it for tests purpose via a hyperterminal connection and it worked.
Maybe the description contains also some helpful information for you.
Here is it:
PC1:
Start "Bluetooth Settings->Custom Mode->Select Remote PC->Select 'Serial Port'->Accept proposed COM port (in my case COM40)->Confirm wizard windows
until setup is finished".
PC2:
Start "HyperTerminal->Select COM7"
PC1:
Start "HyperTerminal->Select COM40 (in my case. See step 1 above)"
PC1, PC2:
Enter the same Passkey if security is turned on e.g. "0000"
PC1:
Everything what you type into HyperTerminal should be visible in HyperTerminal of PC2 and vice versa.

How can i make network between two databases ?

Good Morning to all ;
Going to configure oracle 10g - ( I trying to exchange data between two different databases.
Each database is configured in different operating systems.
For ex : one database from windows XP(seperate virtual machinne)
one database from linux rhel (seperate virtual machinne)
I am waiting for some suggestions ..
Thanks ..
Edited by: 969352 on Mar 19, 2013 10:04 AM

969352 wrote:
What virtualization product are you using?*#* vmware-toolbox-cmd -v
8.1.3.9911 (build-203739)
VMWARE Product Information :
Version : 7.0.0 build - 203739
OK. You will need to make sure the ip addresses you assign to your vms are in the same subnet as the adapter create by the installation of vmware. Once you get the fundamental network setup fixed, you can treat these vms just like any machine in your data center. Forget the vm console and access them exactly like you would any remote server -- putty for the linux machine and Windows Remote Desktop for the Windows machine.
At a command prompt on the host, issue this:
c:> ipconfig -allYou will get back info on several net adapters, two of which are identified as being with vmware -- vmNet1 and vmNet8. Note the IP addresses of both. We'll need it later.
You will also need to know how you configured the network adapters on your vm's -- NAT, bridged, hostonly, ???
Note that these issues are out of scope for this forum. I don't mind helping, but I no longer have a vmware installation to reference details.
What have you actually tried to do? ( Data Transfer )I tried to exchange data from windows database to linux DB
That's pretty vague. Exactly how did you try to "exchange data"? A sql statement using a db_link? export/import? Carrier Pigeon?
>
Where are you stuck?
I don't know , how to configure ip and necessary information for windows database.
Configuring an IP address is purely an OS admin issue and is out of scope for this database forum.
Google is your friend, but only if you use it: [url http://lmgtfy.com/?q=configure+windows+ip+address]http://lmgtfy.com/?q=configure+windows+ip+address
>
That's it Edstevens .. thanks ..

N bridge between two 1252an in bridge mode at 5GHz

I've read in some of the cisco documentation on the 1250 series that root bridge or non root bridge modes are "not tested". They don't say "not supported". I have a client that could use a high bandwidth link between two buildings that are 100' or so apart. The fiber link has already been busted twice. Heavy heavy trucks kill the ground concrete. I have configed a 54Mbps solution with two 1242G's and some cisco yagi's. But, if an N bridge is possible with two 1252AG's, and go faster than the 54Mbps..I'd go with that setup.
Cisco documentation says the bridge modes show up in the 1252 webgui and are selectable. They just end it with "not tested".
Any thoughts?

It became supported in recent versions of the 1250 IOS.
|With this feature, the Cisco Aironet 1140 and 1250 Series can be configured for both access point and bridge functions. Bridging support on 802.11n access points offers added performance, reliability and throughput for basic wireless LAN coverage, wireless LAN coverage with wireless backhaul, and more traditional bridging applications.|
http://www.cisco.com/en/US/partner/prod/collateral/wireless/ps5678/ps6087/product_bulletin_c25-560118_ps6973_Products_Bulletin.html
Nicolas
===
Don't forget to rate answers that you find useful

How to drag and drop button between two toolbar?

Hi,everybody :)
i hava a problem :
if i have two toolbar in a frame , and there are some button in each, how can i use dnd package to drag and drop button between two toolbar,such as drag one button in a toolbar to the other toolbar ,i write some sample code ,but find some difficult to finish
can anyone give me some example code?
Thanks!

hi:)
i have done it ,but there is another problem ,after i finish drag the button and drop it into the toolbar,if my mouse across the dragged button ,it will change the color ,can i setup any mathod to disappear the side_effect?
thank u
click open to show the other frame
and the code is as follows:
import java.awt.*;
import java.awt.datatransfer.*;
import java.awt.dnd.*;
import java.awt.event.*;
import java.io.*;
import javax.swing.*;
public class buttondrag implements DragGestureListener, DragSourceListener,
DropTargetListener, Transferable{
static JFrame source = new JFrame("Source Frame");
static JFrame target = new JFrame("Target Frame");
static final DataFlavor[] supportedFlavors = { null };
static {
try {
     supportedFlavors[0] = new DataFlavor(DataFlavor.javaJVMLocalObjectMimeType);
catch (Exception ex) {
     ex.printStackTrace();
} Object object; // Transferable methods.
public Object getTransferData(DataFlavor flavor) {
if (flavor.isMimeTypeEqual(DataFlavor.javaJVMLocalObjectMimeType)) return object;
else{
return null;
public DataFlavor[] getTransferDataFlavors() {
     return supportedFlavors;
public boolean isDataFlavorSupported(DataFlavor flavor) {
     return flavor.isMimeTypeEqual(DataFlavor.javaJVMLocalObjectMimeType);
} // DragGestureListener method.
public void dragGestureRecognized(DragGestureEvent ev) {
ev.startDrag(null, this, this);
} // DragSourceListener methods.
public void dragDropEnd(DragSourceDropEvent ev) { }
public void dragEnter(DragSourceDragEvent ev) { }
public void dragExit(DragSourceEvent ev) { }
public void dragOver(DragSourceDragEvent ev) {
     object = ev.getSource();
public void dropActionChanged(DragSourceDragEvent ev) { } // DropTargetListener methods.
public void dragEnter(DropTargetDragEvent ev) { }
public void dragExit(DropTargetEvent ev) { }
public void dragOver(DropTargetDragEvent ev) { dropTargetDrag(ev); }
public void dropActionChanged(DropTargetDragEvent ev) { dropTargetDrag(ev); }
void dropTargetDrag(DropTargetDragEvent ev) { ev.acceptDrag(ev.getDropAction()); }
public void drop(DropTargetDropEvent ev) {
     ev.acceptDrop(ev.getDropAction());
     try {
     Object target = ev.getSource();
     Object source = ev.getTransferable().getTransferData(supportedFlavors[0]);
     Component component = ((DragSourceContext) source).getComponent();
     Container oldContainer = component.getParent();
     Container container = (Container) ((DropTarget) target).getComponent();
     container.add(component);
     oldContainer.validate();
     oldContainer.repaint();
     container.validate();
     container.repaint();
     catch (Exception ex) {
          ex.printStackTrace();
          ev.dropComplete(true);
public static void main(String[] arg) {
JButton button = new JButton("Drag this button");
JToolBar sbar = new JToolBar();
JToolBar dbar = new JToolBar();
JButton open_button = new JButton("Open");
source.getContentPane().setLayout(null);
source.setSize(new Dimension(400, 300));
sbar.add(button);
sbar.setBounds(new Rectangle(0, 0, 400, 31));
sbar.add(open_button);
open_button.addMouseListener(new MouseAdapter() {
public void mouseClicked(MouseEvent e) {
target.setVisible(true);
source.getContentPane() .add(sbar);
target.getContentPane().setLayout(null);
target.setSize(new Dimension(400, 300));
target.getContentPane().add(dbar);
dbar.setBounds(new Rectangle(0, 0, 400, 31));
dbar.add(new JButton("button1"));
buttondrag dndListener = new buttondrag();
DragSource dragSource = new DragSource();
DropTarget dropTarget1 = new DropTarget(sbar, DnDConstants.ACTION_MOVE, dndListener);
DropTarget dropTarget2 = new DropTarget(dbar, DnDConstants.ACTION_MOVE, dndListener);
DragGestureRecognizer dragRecognizer1 = dragSource.createDefaultDragGestureRecognizer(button, DnDConstants.ACTION_MOVE, dndListener);
source.setBounds(0, 200, 200, 200);
target.setVisible(false);
target.setBounds(220, 200, 200, 200);
source.show();
}

VoIP Setup between two centers

Similar Messages

Maybe you are looking for