VPN and Windows 2003 DHCP

I have an 871 Router that I am trying to setup a VPN but the Windows 2003 server on the network does the dhcp. At this point I get and error on authentication just trying to vpn - here is the config I hope someone can help. I have never had this problem before
aaa authentication login default local
aaa authentication login sdm_vpn_xauth_ml_1 local
aaa authorization exec default local
aaa authorization network sdm_vpn_group_ml_1 local
aaa session-id common
resource policy
ip subnet-zero
ip cef
ip domain name xxx.com
ip name-server 216.x.x.x
ip name-server 216.x.x.x
crypto isakmp policy 1
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp client configuration group xxxvpn
key xx2cisco
dns 192.168.0.1 216.x.x.x
domain d2b0411
netmask 255.255.255.0
crypto ipsec transform-set xxxvpn esp-3des esp-md5-hmac
crypto dynamic-map SDM_DYNMAP_1 1
set transform-set peruvpn
reverse-route
crypto map SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1
crypto map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1
crypto map SDM_CMAP_1 client configuration address respond
crypto map SDM_CMAP_1 65535 ipsec-isakmp dynamic SDM_DYNMAP_1
interface FastEthernet4
description $ES_WAN$
ip address 216.x.x.x 255.255.255.248
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map SDM_CMAP_1
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 192.168.0.254 255.255.255.0
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
ip local pool SDM_POOL_1 192.168.0.220 192.168.0.225
ip classless
ip route 0.0.0.0 0.0.0.0 216.x.x.x
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source static udp 192.168.0.1 3389 interface FastEthernet4 3389
ip nat inside source route-map SDM_RMAP_1 interface FastEthernet4 overload
access-list 100 remark SDM_ACL Category=2
access-list 100 deny ip any host 192.168.0.220
access-list 100 deny ip any host 192.168.0.221
access-list 100 deny ip any host 192.168.0.222
access-list 100 deny ip any host 192.168.0.223
access-list 100 deny ip any host 192.168.0.224
access-list 100 deny ip any host 192.168.0.225
access-list 100 permit ip 192.168.0.0 0.0.0.255 any
no cdp run
route-map SDM_RMAP_1 permit 1
match ip address 100
Thanks
Gabrielle

OK - I am able to VPN in fine now. I can ping the server 192.168.0.1- I can get in Remote Desktop to the server 192.168.0.1 and from remote desktop I can ping my VPNed Pc IP of 192.168.0.200. However, I can't see the domain when I go to map network or Network neigh. Any Ideas?
Thanks

Similar Messages

WRV54G and VPN and Windows 2003 Server

Hello. I use Windows 2003 Server on my laptop and trying to establish VPN into my WRV54G. QuickVPN is not compatible with the OS, so that's not an option. I tried the manual setup and I got to a point where I had to enter the destination IP address. I use a DynDNS address and so I won't have a static IP.
I'm using firmware version 2.39.2.
Thoughts?
Thanks!

First thing i would like you to check is if you are able to "ping" the WAN ip address for the WRV54G.
Also what are the settings that you have on the WRV ??? typically the remote secure group and remote security gateway should be set at "any".
In the WRV...under the VPn go to advanced VPN and sset the mode to "agressive" , enable keep-alive and netbios broadcast....
let me know if this work or let me know a few more details.

Oracle 9i and windows 2003 R2 installation issues

Hi All,
I have a windows 2003 R2 server with oracle 9.2.0.8 installed both OS and DB are 32bit. The server has 12gb ram and I therefore use AWE and /PAE, however when ever the number of connections exceeds >60 memory errors start to appear and sessions crash. Has anyone out there carried out a successful install of 9i and windows 2003 R2. Can anyone help with the resolution of these issues.
regards
Alan

some more information
I’ve just restarted the server with its full quota of 16GB of RAM and selected both boot.ini switches (/PAE and /3GB) at server startup. I then amended the dbblock_lru_latches parameter from 128 to 64. Before I even started the database I tried running ‘ipconfig /all’ at the command prompt with the following result:
D:\Oracle>ipconfig /all
Windows IP Configuration
An internal error occurred: Insufficient system resources exist to complete the requested service.
Please contact Microsoft Product Support Services for further help.
is it windows causing these issues?
rgds
alan

Any known issues with Flash player 9 and windows 2003 compatibility?

Hi guys..
Is there any known compatibility problem with running flash
applications
on Windows 2003 Server?
My application runs just so well with Windows XP
yet it throws a 2015 bitmap error
when it is being run on the windows 2003 server.
(Not quite often but often enough. the only difference is the
operating
system)
Is there any known issue about this?
Or could there be any compatibility problem with flash player
and
windows 2003?
Any hints would be deeply appreciated...
Thank you...

Hyperion 32-bit Web Apps are fully compatible with Essbase 64-bit. Same with 32-bit Essbase client.

MSI K9N Neo board- and Windows 2003 R2

Hello,
I am having some compatibility issues with running a K9N Neo board and Windows 2003 r2
--I cant get core center to run
--I cant get audio/sound to work, it is all installed except for one thing.
so then i killed by loading XP drivers that it did not like.
Does anyone have a list of the minmum drivers off my CD that i should install to get it going, or are they on the MSI site for W2k3? I could not find them.
This machine works totally fine with XP and Vista.
thanks

That is mostly correct, absolutely. But it happens that Microsoft thought-up some security measure or two that prohibits some - for example - updating procedures. Here is an example, but I doubt that is your problem. Please note the kb number, you don't have to learn Swedish.
http://support.microsoft.com/kb/922582/sv
Modificacion: Very few companies do I believe produce special 2003 drivers. Don't think I ever saw any MSI ones, anyway. Isn't it enough that XP and Vista works? Those are better for gaming, entertainment, VOIP and such.

Clean Access and Windows 2003 Server

I am trying to install the Clean Access Client on a VM running Windows 2003 Server. When I connect to our customer's network the VPN client appears to connect properly and I see the Clean Access window. Then it all seems to fall over. My customer tells me I should see a blue window with a red OK button on it but I never see it. As a result I never get completely into the network. Is this because I am running this on Windows 2003 Server or should I be looking at something else? Can this run in a Virtual Environment and on 2003 Server?

I work it out partially by myself:
1)
(excuse me, I meant "kinit and Krb5LoginModule" not "kinit and kinit.exe").
Krb5LoginModule seems to work now (with TCP). The output is:
KRBError:sTime is Tue Jun 01 17:13:51 CEST 2004 1086102831000
suSec is 945761
error code is 52
error Message is Response too big for UDP, retry with TCP
realm is SSOTEST.RTC.CH
sname is krbtgt/SSOTEST.RTC.CH
KrbKdcReq send: kdc=rtcnt978.ssotest.rtc.ch TCP:88, timeout=30000, number of retries =3, #bytes=232
DEBUG: TCPClient reading 1496 bytes
KrbKdcReq send: #bytes read=1496
KrbKdcReq send: #bytes read=1496
EType: sun.security.krb5.internal.crypto.DesCbcMd5EType
KrbAsRep cons in KrbAsReq.getReply sso_testuserCommit Succeeded
Which is what I want (it tries first with UDP, then the KDC says the TGT is too big for UDP and the client tries again with TCP)
2)
I still have the error :-(

Cisco aironet 1130g and windows 2003 with cisco ACS

hi
i have configured windows 2003 server with DNS ,Active directory users and dhcp server. and configured my cisco 1130g AP .
i have installed cisco access control server 4.0 because i use LEAP authentication protocol and for the ACS for network configuration i give aaa client ip addresss as AP interface ip and same shared secret for the AP and ACS,.
so when i log to wifi it ask username and password
problem is lap top cannot have a ip address my dhcp server not issue any ip address .
my hiper terminal massage is like this when i connect to wifi
help ...thank you...

As I mentioned now several times already, it is the client and ACS which do the PEAP. The Access point doesn't have to be configured for an eap type. What you did on the AP was setting the AP as a radius server which is duplicate work with what you did on ACS.
So you need on your client to configure either PEAP or LEAP.
Nicolas

Windows 2003 DHCP server merge to Solaris 10

Does anyone ever tried to merge a Windows2003 DHCP server to Solaris 10? Especially running this DHCP server in a solaris zone?
I have an old windows 2003 server with 100 DHCP clients that needs be be transported to Solaris so we can get rid of this Windows machine.
Is it possible to read the DHCP backupfile from windows2003 with Solaris?

Troy H wrote:
> Hi,
>
> I have an issue where I do not see SLP being deployed successfully from
> a Windows Server's DHCP scope options. All of the other options come
> through.
>
> I followed this MS doc: http://support.microsoft.com/kb/285019
>
> As far as I can tell, it's setup correctly.
> Has anyone else setup SLP Options in MS and gotten them to work?
> Thank you,
> Troy
Okay, more information:
Workstations that are imaged will receive SLP information as long as the
Zen agent hasn't been installed.(using latest Zen7SP1 Postpatch)
Once you install the Zen agent you will no longer receive SLP via DHCP.
Note that the Novell Client version can be 491 to 491 SP3.
However, if you rename the C:\windows\system32\novell\novdhcp.dll file,
you'll resume getting SLP info from DHCP.(TID 10093676)
Pretty strange, eh?

Cisco vlan setup w a windows 2003 dhcp server help

Can anyone give me some tips or point me to some documentation on setting up a catalyst 4500 series w vlans and a windows 2003 server w associated dhcp scopes? Just for curiosity, what is a good vlan design for a college. I was thinking a student, a staff, a faculty, and a guest and or mgmt vlan. Also, on the guest vlan how would I setup an outbound acl to only allow port 80 traffic? Thanks in advance.

Hi
Try to limit the number of users per vlan to no more than a class C subnet if you can. We use half a class C /25 network in our offices.
If you can break up the vlans to match the different type of users then that would be a good start. It means you can further down the line apply different security policies to the different vlans which in your situation you may well want to do. Don't worry if for example you need to use 2 or 3 vlans for students it's not a problem.
Attached is a link for 4500 configuration. You need to look at the following chapters primarily
1) Configuring VLAN's VTP & VMPS.
2) Configuring Layer 3 interfaces. Look at the section on logical layer 3 SVI's.
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/31sg/configuration/guide/conf.html
On the guest vlan you would need something like (assuming guest vlan subnet range is 192.168.1.0/24
access-list 120 permit tcp 192.168.1.0 255.255.255.0 any eq www
access-list 120 deny ip 192.168.1.0 255.255.255.0 any
and apply it on the inbound vlan interface. ie. if your vlan for guest users is vlan 20
switch(config)# vlan 20
switch(config-if)# ip access-group 120 in
As for the W2003 server, not done much with windows. You will need DHCP manager which should be under admin tools. Make sure you exclude the addresses for each subnet that you allocate to the 4500 layer 3 interfaces ie
switch(config)# vlan 20
switch(config-t)# ip address 192.168.1.1 255.255.255.0
In your DHCP scope 192.168.1.1 will be the default gateway for your clients and you should exclude this from the scope.
Hope this is enough to get you started
Jon

SAP 4.6c with 32 bit kernel and Windows 2003 EE 64 bit - memory issues?

Dear Colleagues.
My apologies for this simple question. I would appreciate your assistance and expertise for this as I think I have confused myself and I would appreciate clarification.
Running an SAP 4.6c system on SAP Kernel 46D_EXT2 32-bit with Windows 2003 Enterprise Edition 64-bit and ORACLE 10.2 64 bit.
Could you confirm that there is still memory address space limitations due to the 32-bit SAP kernel?
It is the SAP Kernel that determines the addressable operating system limit for R/3 extended memory under Windows NT?
Do I still need to set the 3GB option on the system to allocate more than 2.5GB of SAP buffers and extended memory space?
I have taken a look at SAP Notes 110172 and 129813, but I just need clarification?
Thanking you in advance.
Kind Regards,
Alcatz

> Could you confirm that there is still memory address space limitations due to the 32-bit SAP kernel?
Yes.
>> It is the SAP Kernel that determines the addressable operating system limit for R/3 extended memory under Windows NT?
On a 64bit OS it is a bit different, effectively you can use 4 GB per workprocess.
> Do I still need to set the 3GB option on the system to allocate more than 2.5GB of SAP buffers and extended memory space?
No.
Markus

Problems with Active Directory and Windows 2003

Hello,
I'm using Mac OS X Server 10.4.9 with Active Directory bound to a Windows 2003 Active Directory Domain. I can bind successfully to the domain using the graphical interface. Then in Samba I can access shared directories using Windows users. However, after some time somehow there are problems and Windows users aren't authenticated anymore on the Mac. I've looked at the firewall and there are no denied packets from the Mac. There are two servers in the domain, all clocks are synchronized and domain information is up to date. When I unbind the Mac, I can see the machine account being deleted on both domain servers and created too on both machines when I bind to the domain.
Problems occur when I try login in using ssh or samba do I think this is a problem with the AD module.
I turned on debugging messages on DirectoryServices:
sudo killall -USR1 DirectoryService
When in Windows, using the Administrator user I try:
net use \\10.0.0.1 /user:domain\Administrator
Where 10.0.0.1 is the Mac.
In the Mac I get from
tail -f /Library/Logs/DirectoryService/DirectoryService.debug.log |grep ADPlug
2007-06-27 10:48:37 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:37 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:37 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:37 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:37 CDT - ADPlugin: Searching domain domain.com.mx for User administrator
2007-06-27 10:48:37 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:37 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:37 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:37 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:37 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:37 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:37 CDT - ADPlugin: Adding Search for Attribute displayName containing DOMAIN\administrator
2007-06-27 10:48:37 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=DOMAIN\\administrator)), limit 1
2007-06-27 10:48:37 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:37 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:37 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:37 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:37 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:37 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:37 CDT - ADPlugin: Searching domain domain.com.mx for User administrator
2007-06-27 10:48:37 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:37 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:37 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:37 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:37 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:37 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:37 CDT - ADPlugin: Adding Search for Attribute displayName containing domain\administrator
2007-06-27 10:48:37 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=domain\\administrator)), limit 1
2007-06-27 10:48:37 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:37 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:37 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:37 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:37 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:37 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:37 CDT - ADPlugin: Searching domain domain.com.mx for User ADMINISTRATOR
2007-06-27 10:48:37 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:37 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:37 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:37 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:37 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:37 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:37 CDT - ADPlugin: Adding Search for Attribute displayName containing domain\administrator
2007-06-27 10:48:37 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=DOMAIN\\ADMINISTRATOR)), limit 1
2007-06-27 10:48:37 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:37 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:37 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:37 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:37 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:37 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:37 CDT - ADPlugin: Locating User with Query (&(objectCategory=person)(|(cn=administrator)(sAMAccountName=administrator)(dis playName=administrator)(mail=administrator)(userPrincipalName=administrator)(use rPrincipalName=administrator@*)))
2007-06-27 10:48:37 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:37 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:37 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:37 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:37 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:37 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:37 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:37 CDT - ADPlugin: Adding Search for Attribute displayName containing ADMINISTRATOR
2007-06-27 10:48:37 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=administrator)), limit 1
2007-06-27 10:48:37 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:37 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:37 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:37 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:37 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:37 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:37 CDT - ADPlugin: Locating User with Query (&(objectCategory=person)(|(cn=ADMINISTRATOR)(sAMAccountName=ADMINISTRATOR)(dis playName=ADMINISTRATOR)(mail=ADMINISTRATOR)(userPrincipalName=ADMINISTRATOR)(use rPrincipalName=ADMINISTRATOR@*)))
2007-06-27 10:48:37 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:38 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:38 CDT - ADPlugin: Adding Search for Attribute displayName containing ADMINISTRATOR
2007-06-27 10:48:38 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=ADMINISTRATOR)), limit 1
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:38 CDT - ADPlugin: Locating User with Query (&(objectCategory=person)(|(cn=administrator)(sAMAccountName=administrator)(dis playName=administrator)(mail=administrator)(userPrincipalName=administrator)(use rPrincipalName=administrator@*)))
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:38 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:38 CDT - ADPlugin: Adding Search for Attribute displayName containing ADMINISTRATOR
2007-06-27 10:48:38 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=administrator)), limit 1
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:38 CDT - ADPlugin: Locating User with Query (&(objectCategory=person)(|(cn=ADMINISTRATOR)(sAMAccountName=ADMINISTRATOR)(dis playName=ADMINISTRATOR)(mail=ADMINISTRATOR)(userPrincipalName=ADMINISTRATOR)(use rPrincipalName=ADMINISTRATOR@*)))
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:38 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:38 CDT - ADPlugin: Adding Search for Attribute displayName containing ADMINISTRATOR
2007-06-27 10:48:38 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=ADMINISTRATOR)), limit 1
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:38 CDT - ADPlugin: Searching domain domain.com.mx for User administrator
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:38 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:38 CDT - ADPlugin: Adding Search for Attribute displayName containing DOMAIN\administrator
2007-06-27 10:48:38 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=DOMAIN\\administrator)), limit 1
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:38 CDT - ADPlugin: Searching domain domain.com.mx for User administrator
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:38 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:38 CDT - ADPlugin: Adding Search for Attribute displayName containing domain\administrator
2007-06-27 10:48:38 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=domain\\administrator)), limit 1
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:38 CDT - ADPlugin: Searching domain domain.com.mx for User ADMINISTRATOR
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:38 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:38 CDT - ADPlugin: Adding Search for Attribute displayName containing DOMAIN\ADMINISTRATOR
2007-06-27 10:48:38 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=DOMAIN\\ADMINISTRATOR)), limit 1
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:38 CDT - ADPlugin: Locating User with Query (&(objectCategory=person)(|(cn=administrator)(sAMAccountName=administrator)(dis playName=administrator)(mail=administrator)(userPrincipalName=administrator)(use rPrincipalName=administrator@*)))
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:38 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:38 CDT - ADPlugin: Adding Search for Attribute displayName containing ADMINISTRATOR
2007-06-27 10:48:38 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=administrator)), limit 1
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:38 CDT - ADPlugin: Locating User with Query (&(objectCategory=person)(|(cn=ADMINISTRATOR)(sAMAccountName=ADMINISTRATOR)(dis playName=ADMINISTRATOR)(mail=ADMINISTRATOR)(userPrincipalName=ADMINISTRATOR)(use rPrincipalName=ADMINISTRATOR@*)))
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:38 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:38 CDT - ADPlugin: Adding Search for Attribute displayName containing ADMINISTRATOR
2007-06-27 10:48:38 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=ADMINISTRATOR)), limit 1
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:38 CDT - ADPlugin: Locating User with Query (&(objectCategory=person)(|(cn=administrator)(sAMAccountName=administrator)(dis playName=administrator)(mail=administrator)(userPrincipalName=administrator)(use rPrincipalName=administrator@*)))
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:38 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:38 CDT - ADPlugin: Adding Search for Attribute displayName containing ADMINISTRATOR
2007-06-27 10:48:38 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=administrator)), limit 1
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Calling GetRecordList Routine
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:38 CDT - ADPlugin: Locating User with Query (&(objectCategory=person)(|(cn=ADMINISTRATOR)(sAMAccountName=ADMINISTRATOR)(dis playName=ADMINISTRATOR)(mail=ADMINISTRATOR)(userPrincipalName=ADMINISTRATOR)(use rPrincipalName=ADMINISTRATOR@*)))
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:38 CDT - ADPlugin: Calling AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RealName
2007-06-27 10:48:38 CDT - ADPlugin: Adding Search for Attribute displayName containing ADMINISTRATOR
2007-06-27 10:48:38 CDT - ADPlugin: Did DC search with queryFilter = (&(objectCategory=cn=person,cn=schema,cn=configuration,dc=domain,dc=com,dc=mx)( displayName=ADMINISTRATOR)), limit 1
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: 16784372 - Put 0 records in Buffer for AttributeValueSearch
2007-06-27 10:48:38 CDT - ADPlugin: Calling OpenDirNode
2007-06-27 10:48:38 CDT - ADPlugin: Opening Specific Node domain.com.mx
2007-06-27 10:48:38 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:38 CDT - ADPlugin: 16833877 - Calling GetRecordList Routine
2007-06-27 10:48:38 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:38 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:38 CDT - ADPlugin: Locating User with Query (&(objectCategory=person)(|(cn=administrator)(sAMAccountName=administrator)(dis playName=administrator)(mail=administrator)(userPrincipalName=administrator)(use rPrincipalName=administrator@*)))
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:38 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:38 CDT - ADPlugin: 16833877 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:38 CDT - ADPlugin: Calling CloseDirNode
2007-06-27 10:48:42 CDT - ADPlugin: Calling OpenDirNode
2007-06-27 10:48:43 CDT - ADPlugin: Opening Specific Node domain.com.mx
2007-06-27 10:48:43 CDT - ADPlugin: Calling GetRecordList
2007-06-27 10:48:43 CDT - ADPlugin: 16833881 - Calling GetRecordList Routine
2007-06-27 10:48:43 CDT - ADPlugin: Search Records called in ADSWrapper
2007-06-27 10:48:43 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-06-27 10:48:43 CDT - ADPlugin: Locating User with Query (&(objectCategory=person)(|(cn=administrator)(sAMAccountName=administrator)(dis playName=administrator)(mail=administrator)(userPrincipalName=administrator)(use rPrincipalName=administrator@*)))
2007-06-27 10:48:43 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:43 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-06-27 10:48:43 CDT - ADPlugin: Returning 0 Results
2007-06-27 10:48:43 CDT - ADPlugin: 16833881 - Put 0 records in Buffer for RecordList
2007-06-27 10:48:43 CDT - ADPlugin: Calling CloseDirNode
I really don't know what to do. The Windows Event log shows no messages. The link used to work and there have been no changes in the domain servers.
The key line seems to be:
2007-06-27 10:48:43 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
But I don't know what that ADSEngine.mm is.
XServe G5 Mac OS X (10.4.9)

Hello.
Thanks for your reply.
I tried the net use with a drive letter with and without the /user switch. When I use a domain user domain\user1 I can't connect. When I use a user local to the XServe it works.
When I use
net use x: \\10.0.0.1\share /user:domain\user1
I get prompted for a password, but it doesn't work.
I checked the firewall and all packets to or from the mac are accepted, no denied or dropped packages.
I already went through the MS document on fw ports. Before I opened to Kerberos ports the binding failed. No the binding work OK.
Some users who were authenticated yesterday still can access files using the Windows domain accounts. It's new users trying to connect those who have problems.
This is what the Samba log.smbd log shows:
[2007/07/04 14:58:45, 2] /SourceCache/samba/samba-100.7/samba/source/smbd/sesssetup.c:setupnew_vcsession(662)
setupnew_vcsession: New VC == 0, if NT4.x compatible we would close all old resources.
[2007/07/04 14:58:45, 2] /SourceCache/samba/samba-100.7/samba/source/smbd/sesssetup.c:setupnew_vcsession(662)
setupnew_vcsession: New VC == 0, if NT4.x compatible we would close all old resources.
[2007/07/04 14:58:46, 0] /SourceCache/samba/samba-100.7/samba/source/auth/authutil.c:make_server_infoinfo3(1138)
makeserver_infoinfo3: pdbinitsam failed!
[2007/07/04 14:58:46, 0] pdbods.c:odssamgetsampwnam(2329)
odssam_getsampwnam: [0]getsam_recordattributes dsRecTypeStandard:Users no account for 'user1'!
[2007/07/04 14:58:46, 2] /SourceCache/samba/samba-100.7/samba/source/auth/auth.c:checkntlmpassword(367)
checkntlmpassword: Authentication for user [user1] -> [user1] FAILED with error NTSTATUS_NO_SUCHUSER
This is what the DS log shows:
2007-07-04 14:58:46 CDT - ADPlugin: 16892201 - Calling GetRecordList Routine
2007-07-04 14:58:46 CDT - ADPlugin: Search Records called in ADSWrapper
2007-07-04 14:58:46 CDT - ADPlugin: Searching attribute: dsAttrTypeStandard:RecordName
2007-07-04 14:58:46 CDT - ADPlugin: Locating User with Query (&(objectCategory=person)(|(cn=user1)(sAMAccountName=user1)(displayName=user1)( mail=user1)(userPrincipalName=user1)(userPrincipalName=user1@*)))
2007-07-04 14:58:46 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-07-04 14:58:46 CDT - ADPlugin: Failed getting credentials at line 2687 in ADSEngine.mm
2007-07-04 14:58:46 CDT - ADPlugin: Returning 0 Results
2007-07-04 14:58:46 CDT - ADPlugin: 16892201 - Put 0 records in Buffer for RecordList
XServe G5 Mac OS X (10.4.9)

Cannot establish a link between MacPro and Windows 2003 Server

I just had an issue where we had a server crash. This server supports several PCs, as well as two Macs. The server has been brought back online and can communicate with all of the PCs. However, neither one of the Macs can now communicate with the server.
When I try to connect through the sidebar in the finder window, it will bring up the authentication window. But after I type in my password and hit enter, it gives me the message, "The alias "" could not be opened because the original item could not be found."
When I try to connect through Go>Connect to Server, it gives me the message, "The Finder cannot complete the operation because some data in "" could not be read or written (Error code -36).
My IT guy says that everything is alright with the server and that the problem has to be in the Mac settings. He does not know anything about Macs, however.
Can somebody help me out with this issue?

The only thing that comes to mind is a few settings in the Security Options of the Local Policy. Here's a link:
http://allinthehead.com/retro/218/accessing-a-windows-2003-share-from-os-x
Not sure if that's it, but I hope it helps.

SCEP on ISE 1.2 and Windows 2003 Server

Hi there
has anyone ever be able to get SCEP on ISE 1.2 working with Windows 2003 Server? I know Cisco recommends Windows 2008 Server onwards, but sometimes the server infrastructure is not yet there.
Thanks in advance and best regards
Dominic

Hmm, good question that I would also like to know the answer to. All of my deployments have been either 2008 or 2012. I believe long time ago I got it working in my lab with 2003 but then my 2003 server blew up so when I re-created it I did it with 2008. However, I cannot confirm 100% and even if it was true it was not in a full production environment. So it would be nice if someone else can chime in here.
I did come across this though that would suggest that it is supported with some tweaks:
http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Borderless_Networks/Unified_Access/BYOD_Design_Guide/BYOD_ISE.html
Windows Server 2003, Microsoft SCEP (MSCEP) required a Resource Kit add-on to be installed on the same computer as the CA. In Windows Server 2008, MSCEP support has been renamed NDES and is part of the operating system. NDES may be installed on a different computer than the CA (http://technet.microsoft.com/en-us/library/cc753784%28WS.10%29.aspx).
Thank you for rating helpful posts!

OS 10.3.9 and Windows 2003 Server - Can't get to the network

My company just up graded from a Windows 2000 to a Windows 2003 server. I am lone Mac user. Yesterday, with Windows 2000, I had no trouble accessing several drives on the server. Now with this upgrade, I can't log on to any of the drives.
The IT folks are not that Mac savvy and they've tried a few things regarding security, but they're lost, and haven't found anything from Microsoft that helps. And I know nothing about networking. I've tried searching Apple but can't find anything specific to this problem. I can print to all the networked printers, just can't get to the drives.
Is there something we're missing here? Something in my System Preferences that we needed to adjust first?
Thanks.
Power Mac G5 Mac OS X (10.3.9)
Power Mac G5 Mac OS X (10.3.9)

My company just up graded from a Windows 2000 to a Windows 2003 server. I am lone Mac user. Yesterday, with Windows 2000, I had no trouble accessing several drives on the server. Now with this upgrade, I can't log on to any of the drives.
The IT folks are not that Mac savvy and they've tried a few things regarding security, but they're lost, and haven't found anything from Microsoft that helps. And I know nothing about networking. I've tried searching Apple but can't find anything specific to this problem. I can print to all the networked printers, just can't get to the drives.
Is there something we're missing here? Something in my System Preferences that we needed to adjust first?
Thanks.
Power Mac G5 Mac OS X (10.3.9)
Power Mac G5 Mac OS X (10.3.9)

ZFS and Windows 2003 Diskpart

I was given some space on a thumper that has zfs drives. I connect from a Windows 2003 using ISCI. I was running out of space and the admin gave me more space which ended up with my losing the drive, but it came back (is that normal). When I went to use diskpart to expand the drive to the additional space, it would not work. Can I not use diskpart to extend the drive size or do I need to something additional?
Thanks for your help.

Earl,
I'm stuck with the 2003 itunes install problem, too. Can you post or email your solution?
THANKS,
Glenn

VPN and Windows 2003 DHCP

Similar Messages

Maybe you are looking for