VPN ERROR 619 :: A connection to the remote computer could not be established, so the port used for this connection was closed
I have been searching endlessly for this issue. Every time I try to connect to a VPN connection I get the error above. Thank you for any relevant input concerning this matter. My NIC is Qualcomm Atheros and I'm in Win8.1 x64.
everything normal before?
is there any changes before this issue happen?
turn off your antivirus and firewall, update the latest VPN client software, if still not working go to security settings and change the VPN type automatic to PPTP. And also change data encryption configuration to Optional and select CHAP & MS-CHAP v2.
If still not working try with other internet connection and try to contact your VPN provider
Similar Messages
-
Windows VPN: Error 720 - A connection to the remote computer could not be established
Dear all
I have a windows7 Laptop 64bit Dell 1340.
I was working with a UMTS card, was connected with a VPN to a windows 2003 server over PPTP and experienced a bluescreen. After this, I have the following errors when connecting to the VPN:
"Registering your computer on the network... Error 720: A connection to the remote computer could not be established. You might need to change the network settings for this connection"
and in the event view I receive the following:
EventID: 1, Source RasSstp
CoId={A3478DFD-FFA4-4E8F-9DA3-CE829BDA777B}:The initial Secure Socket Tunneling Protocol request could not be successfully sent to the server. This can be due to network connectivity issues or certificate (trust) issues. The detailed error message is provided below. Correct the problem and try again.
I tried to use the Rarepair.exe tool but it looks to work only on windows xp. I deleted the IP and TCP settings without any luck.
I run a registry cleaner as well with out any luck.
Your help will be greatly appreciated!
MarcHi,
Since it worked previously, a quick solution is to run System Restore and get back to the previous status when the issue didn’t occur.
If system restore doesn’t help, please also try the following:
1. Check if you can establish the VPN via other connections except the connection through the UMTS card.
2. Reset the PPTP and L2TP WAN miniport with running the following commands one by one in an elevated command prompt:
Netcfg -u MS_L2TP
Netcfg -u MS_PPTP
Netcfg -l %windir%\inf\netrast.inf -c p -i MS_PPTP
Netcfg -l %windir%\inf\netrast.inf -c p -i MS_L2TP
Then reboot the computer and see how it works.
Meanwhile, I would like to share the following with you for your reference:
Troubleshooting common VPN related errors
Hope this helps. Thanks.
Nicholas Li - MSFT -
Trying to set up Blackberry Torch for laptop tethering...bluetooth. I have connection/drivers/etc. but keep getting error message: "Error 720: A connection to the remote computer could not be established. You might need to change the network settings for this connection." Where and what do I chancge setting to so this will work?
I have synched my phone and laptop wirelessly across other internet connection....just cant get this above to work. Anybody know how to fix this? Thanks!Hi,
Since it worked previously, a quick solution is to run System Restore and get back to the previous status when the issue didn’t occur.
If system restore doesn’t help, please also try the following:
1. Check if you can establish the VPN via other connections except the connection through the UMTS card.
2. Reset the PPTP and L2TP WAN miniport with running the following commands one by one in an elevated command prompt:
Netcfg -u MS_L2TP
Netcfg -u MS_PPTP
Netcfg -l %windir%\inf\netrast.inf -c p -i MS_PPTP
Netcfg -l %windir%\inf\netrast.inf -c p -i MS_L2TP
Then reboot the computer and see how it works.
Meanwhile, I would like to share the following with you for your reference:
Troubleshooting common VPN related errors
Hope this helps. Thanks.
Nicholas Li - MSFT -
Error 720: A connection to the remote computer could not be established.
So I got an aircard Novatel P720. It was working fine for months. Then I installed a VPN connection. Now, I get this error.
Error 720: A connection to the remote computer could not be established.
Most of of what I found recommends uninstalling the WAN Miniport (IP), it seems that I have to go thru so many hoops to get this fixed. Wondering if I would be better off rebuilding my machine from scratch again. Is there an patch or another way to get me going.
I think this is an old issue. Lots of comments on this thru Google. I am hoping I can get a definative answer from Lenovo's itself!josezald wrote:
So I got an aircard Novatel P720. It was working fine for months. Then I installed a VPN connection. Now, I get this error.
Error 720: A connection to the remote computer could not be established.
Most of of what I found recommends uninstalling the WAN Miniport (IP), it seems that I have to go thru so many hoops to get this fixed. Wondering if I would be better off rebuilding my machine from scratch again. Is there an patch or another way to get me going.
I think this is an old issue. Lots of comments on this thru Google. I am hoping I can get a definative answer from Lenovo's itself!
Well, seeing since your having an Issue with a non Lenovo product. I dont think your going to get an official answer from Lenovo. You may get suggestions however.
Ignorance is no excuse! -
Error 720 a connection to the remote computer could not be established win 8
hello, i have this error on my windose 8, error 720 a connection to the remote computer could not be established ,for VPN connection, how can i fix it ?
Hi,
For this issue,I would like to know your VPN protocol.
Did you use Windows in-built VPN client?
I think the issue is related to your security software or Firewall.
Let’s temporarily disable other security software and Windows firewall to check if that helps.
If it doesn't work, please uninstall the third-party security software or firewall to test it.
Also, please check your event view to see if there are some related error in it.
Regards,
Kelvin hsu
TechNet Community Support -
The remote computer could not be found. please contact your helpdesk
RDS Farm set up as follows 3- RD Session Host/Web servers set up as network load balanced and 2-RD Connection broker servers set up as clustered servers. I access the RdWeb farm from the internet via VPN clientless. I can get into
RdWeb with no problems, however I have few clients that can connect to RdWeb portal but once they open any application icon the error gets displayed "the remote computer could not be found. please contact your helpdesk ". The client
pc is Windows 8 with IE11 and Windows 7 with IE 10. I could not find anything that related to some users that could not connect. Help!Hi,
Firstly please provide some more information from your side.
1. Does the other user can able to work properly without any issue?
2. Did you install the RD gateway role to allow the external user to access the internal resource? If so, please help to make sure you configure the FQDN for the RD gateway, and the external users can resolve this name on the internet.
3. Can you telnet the RD host server (like telnet server name 3389) to check whether the RD host server is available for another server?
4. Did you try to temporarily disable all of firewall and anti-virus to test if this issue persists?
You can configure RD Web Access behavior on IIS manager as per below.
IIS Manager Console > Default Web Site > RDWeb > Pages > Application Settings > DefaultTSGateway > add the "FQDN of the Remote Desktop Gateway"
After finishing all above steps, please launch the RemoteApp again to see if the same issue still exists. For more information, you can refer beneath article.
Configure Remote Desktop Web Connection Behavior
Hope it helps!
Thanks. -
The remote computer could not be found
Guys,
Im having this error message pop up when I launch a remoteapp from an external network through the rd web access page. On the deployment settings I have the gateway setting to "automatically detect rd gateway server settings". This always givves
me this error regardless of whether I edit the rdweb access application settings and add the defaultTSGateway : External FQDN.
If I switch the rd gateway settings in deployment proprties to "Use this rd gateway server setting" : external FQDN it works fine.
can someone tell me why? how does the automatically detect rd gateway server setting work and if it's even supposed to work if I am accessing apps externally?Hi,
You should select Use these RD Gateway server settings in most cases. Automatically detect is for when the client PCs are domain-joined and you have specified the RD Gateway settings using group policy.
-TP -
Remote Computer could not be found?
I have setup a Web Access RemoteApp server on Server 2008 R2 and it is no longer letting anyone connect to apps or use remote desktop from the outside. If I try to run any apps or try to RDP from the Web Access site it tries to launch but then I get a "The Remote Computer could not be found" error. It was working earlier today, I was able to launch applications from home but it now gives me that error.
Setup is as follows: All TS roles are installed on TSserver except the virtualization host since this is not a Hyper-V server. All the consoles show no issues, I have everything pointing to TSserver. I have an external site setup (remote.domain.com) and it is working. I can get to the site fine, apps populate fine and overall there are no issues there. If I go to the RemoteApp server internally I can launch applications and rdp without a problem. It's just externally that they're not working.
I admit I'm new to all these new TS roles and just started setting this all up. But I can't figure out why this was working earlier today and now is not. The only changes I made were a redirect for IIS (so that users only have to type in remote.domain.com instead of https://remote.domain.com/rdweb) and I installed a new application (though a co-worker said he started getting that error before I installed that program).
What should I be looking at to resolve this? The fact that it works internally and that I can get to the site externally makes me think it's some small setting I'm missing. With so many different management consoles to look through it's a little difficult to pinpoint what's wrong.Hi,
Simple sharing of credentials between RD Gateway and RDS server can be enabled by doing the following :
On the RD Session Host server, open RemoteApp Manager. To open RemoteApp Manager, click Start, point to Administrative Tools, point to Remote Desktop Services, and then click RemoteApp Manager.
In the Actions pane of RemoteApp Manager, click RD Gateway Settings. (Or, in the Overview pane, next to RD Gateway Settings, click Change.)
Select the Use these RD Gateway server settings.
In the Logon box, select the Ask for password (NTLM).
Select the Use the same user credentials for RD Gateway and RD Session Host server check box.
Click OK to close the RemoteApp Deployment Settings dialog box.
If you want to enable web single sign on , please take a look at the following blog -
http://blogs.msdn.com/rds/archive/2009/08/11/introducing-web-single-sign-on-for-remoteapp-and-desktop-connections.aspx
Thanks,
Kaustubh -
I have configure remote access feature web application proxy but not configure give the error. The remote name could not be resolved in server 2012 R2.
I have configure Ad and ADFS different server and try to configure web application proxy different server. what setting are required for connect web application proxy to Ad and ADFS.Hi,
In addition, please make sure that the port 443 is not blocked by the firewall.
Web Application Proxy requires internal name resolution to resolve the names of backend servers, and AD FS servers. When publishing web applications via Web Application Proxy, every web application you publish requires an external URL. For clients to reach
these web applications, a public DNS server must be able to resolve each external URL that you configure. Note that the external URL must resolve to the same IP address as the Web Application Proxy server, or the external IP address of a firewall or load-balancer
placed in front of the Web Application Proxy server.
Best regards,
Susie
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] -
This is a new problem for an IPod Touch I have had for a year. The IPod is hooked up by cable and appears in ITunes. I can examine all the content on the IPOD and I can click "sync". It goes through to Step 7 and then the error messages occur. First "a session could not be started with the IPod" and when that dialogue box is closed, the message "a connection could not be established to the IPod."
Maybe:
Sync Session Failed to Start iTouch iOS5: Apple Support Communities
iphone could not be synced sync session failed to start...: Apple Support Communities -
Azure File Storage error The remote name could not be resolved
I am following http://azure.microsoft.com/en-us/documentation/articles/storage-dotnet-how-to-use-files/
While executing $s = New-AzureStorageShare mysampleshare -Context $ctx I get error as
New-AzureStorageShare : The remote name could not be resolved: 'mystorageaccount.file.core.windows.net'
At line:1 char:6
+ $s = New-AzureStorageShare elasticsearch -Context $ctx
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : CloseError: (:) [New-AzureStorageShare], StorageException
+ FullyQualifiedErrorId : StorageException,Microsoft.WindowsAzure.Commands.Storage.File.Cmdlet.NewAzureStorageShare
Thanks,
SubodhAzure Files is a Preview feature. Did you request and got access to it at the billing portal's Preview Features (https://account.windowsazure.com/PreviewFeatures)?
Also, you can now try creating the File share via the Preview Portal (https://portal.azure.com -> your storage account -> "File Shares"). -
Hi
I am trying to setup a Power BI On Premise datasource at a client site.
I successfully installed the Data Management Gateway (DataManagementGateway_1.2.5303.1_en-us (64-bit)) software on a Windows Server 2012 box and created the Gateway on the Power BI Office 365 site.
The Gateway is running correctly with no errors. When trying to setup the Datasource I get an error. As soon as I try to set the credentials the following message appears.
Failed to verify gateway 'GatewayName' status. The remote name could not be resolved: 'servername.domainname.net’
The servername which is returned in the error message is exactly the name which the DMG was installed on.
There is a firewall in place with a proxy server and I don't know if this might cause the problems. The
following website suggests adding the proxy settings in the config files of the DMG but this did not solve the problem.
The above setup process works perfectly when running the DMG from my laptop, connecting to a Gateway and creating a DataSource connecting to SQL Server.
Any assistance would be appreciated.HI
Thank You for the reply.
I resolved the issue in the mean time. I was on laptop which does not belong to the domain.
When setting up the datasource you should be on the same domain as the datasource as per the below post.
http://sharepoint-community.net/profiles/blogs/connecting-office-365-to-on-premises-data
Regards, Drickus -
Our home folders are stored on a non-windows NAS device and with Windows XP and 2003 we've always got the above error when creating or modifying users home folders, even when the shares were al ready created and being used.
However this was never really a big issue as the error that popped up was really for information and finshed with a "we've modified the user properties anyway, please create the share manually" type message.
Unfortunately now we are moving to windows 7 and 2008R2, this last part of the the message is missing and it won't accept the correct value.
This issue may be in the way that the NAS device shares the folder, as only the username that matches the folder name can access the share. This behaviour can't be modified.
Is there a way to get Windows 7/2008R2 AD users and computers to behave the same way that Windows XP/2003 does , i.e. don't try and create the share just set the value in the user properties ?
The AD is still at 2003 level and we can still use Windows XP/2003 clients to make the changes but this is a bit of a limitation.The KB article is almost what we have apart from theitalic underlined
part
Consider the following scenario:
You use a domain administrator account to log on to a computer that is running Windows 7 or Windows Server 2008 R2.
You use the Active Directory Users and Computers Microsoft Management Console (MMC) snap-in to connect to a domain controller.
You open the Properties dialog box of a user account.
The user account has sole access to a shared folder path that cannot be accessed by the administrator account.
You set the Remote Desktop Services Home Folderattribute to the shared folder path.
NoteThis attribute is located on the
Remote Desktop Services Profiletab.
You click Apply or OK.
In this scenario, you receive the following error message:
The home folder could not be created because: The network name cannot be found.
Note If you click Apply or OK again, no error message is returned. However, the setting is not saved.
I think the important bit is
The user account has sole access to a shared folder path that cannot be accessed by the administrator account.
We manually create the shares on our NAS and then just want to enter the path in the profile tab, I suppose the question is how to we stop it trying to create the shares ? -
The remote name could not be resolved
We are running Office 365 Power BI (as a trial) and published our data through the data manager gateway service.
We are able to retrieve a list of shared tables / views through Power Query in Excel 2013 Professional Plus.
However, when clicking on edit on any table returned we get this error in the Power Query window:
DataSource.Error: OData: Request failed (NameResolutionFailure):
The remote name could not be resolved: 'SERVER-NAME.DOMAIN.local'
Details: https://POWERBISITE.hybridproxy.powerbi.com/ODataService/v1....
I have tried configuring the Data Manager Gateway service to run HTTP (at first) and HTTPS.
Could this be a port number issue? Or what else?
Appreciate any help, Thank you
IanHi intrasight,
I gave the hosts thing a try.
I was getting 'unable to resolve' errors in attempting to use Power Query in a small stand-alone test domain (all computers are in the domain, and in this little LAN). So I edited
hosts in C:\Windows\System32\drivers\etc
I added this line:
192.168.0.4 mycomputer.ad.mydomain.com
mycomputer is the name of the computer running the Data Management Gateway, and
ad.mydomain.com is the name of the domain.
Now, I get
<textarea class="role-selectableText" cols="1" readonly="readonly" rows="1" style="width:659px;height:87px;" tabindex="-1">DataSource.Error: OData: Request failed: The underlying connection was closed: Could not establish trust relationship for the SSL/TLS
secure channel. Details: https://mydomain.hybridproxy.powerbi.com/ODataService/v1.0/mydatasource</textarea>
Which tells me that hosts on the client is indeed now resolving the name/IP correctly, and Power Query is finding the DMG directly (rather than via the
hybridproxy.powerbi.com cloud service).
But that's terrible!
A) I shouldn't need to use hosts since
B) the hybridpproxy cloud service is finding the DMG on my database machine (because the Test Connection works OK)
C) but without hosts the client Power Query says that "The remote name could not be resolved"
DataSource.Error: OData: Request failed: The remote name could not be resolved: 'mycomputer.ad.mydomain.com'
Details:
https://mydomain.hybridproxy.powerbi.com/ODataService/v1.0/mydatasource
There's no way an actual production system should require editing
hosts on all client machines.
So to my mind, the original question is still outstanding.
How do I get Power Query to resolve the remote name?
Cheers, Donna
Donna Kelly -
Itunes could not sync because a connection could not be established to the Iphone
I have been trying to sync my 4s and I keep getting "Itunes could not sync because a connection could not be established to the Iphone"
I am also getting this error with two iPad 2s and an iPhone 5. All are on iOS 6.0.1 and this is with iTunes 11 on a Windows 7 PC. I also have an iPhone 4 that does not seem to have an issue that I can tell. When I plug in the iPhone 5 and one of the iPads, it will start to to sync and right at the end I get that message. It will, however, still continue to sync the device after the error message pops up. With the one iPad, which is rarely connected to computer, it will find the iPad via wifi when iTunes is opened, but I will get that message when it is performing its initial sync.
While I kept having sync issues when using iTunes 10.7, this is a new issue for me. I was also getting a lot of warnings that the iPhone or iPad could not be synced because the connection was lost even though the iPad and iPhone were connected via USB cable. In those cases, the sync would just abort. I have not gotten that error though in two days. At the time to resolve that issue, I needed to disconnect the USB cable, reset the iPhone/iPad, and then reconnect the USB cable.
I really wish Apple would figure out these sync issues.
- Merg
Maybe you are looking for
-
Crystal report Error for CRVS2010 sp2 using Push Method
I am trying to pass a dataset to a crystal report viewer using SetDatabaseSource. I have defined in Crystal to used an ADO .Net Database XML Schema. I pass a Dataset to the Report By using SetDatbaseSourece and set the ReportSource for the CrystalVie
-
Me and my sister use the same itunes but on my new iphone i have a different apple id. how do i hook up my iphone to get the music from her account on to my iphone because my iphone wont show up in our itunes.
-
Cannot open pdf's from internet
I installed Adobe reader but found it wasn't necessary. After uninstalling it I cannot open pdf's from the internet. When I try all that opens is a blank screen. How can I fix this?
-
IWeb blog pages versus TypePad, Blogger / Blogspot
Hello bloggers, I want to start a blog to share my thoughts, ideas and photo snapshots. My question is: should I do that with iWeb and my dot Mac account, or use one of the on-line services like Blogger.com? What are the pros an cons of those two wor
-
Recording and Replaying Ejb Calls
Hi All, Recently i have developed an application for jboss AS which record Ejb outgoing invocations from a J2EE Client Application in XML form using AspectJ instrumentation. In Jboss case the recorded invocations are Dynamic Proxies with their handle