WAP300N No Web interface or Connectivity after 3 - 4 hrs of uptime

I recently purchased 3 WAP300N devices to revamp my wireless solution in the office. I have configured two of them so far and both are experiencing the same problem. They are running in Access Point mode with static IP's and are set to run on different channels (6 and 11) are set to mixed network mode and share the same SSID to allow my users to roam the office. About as basic of a configuration as you can put on an AP.
After about 3-4 hours of uptime the AP's "lockup" by this I mean I can longer access them through the web portal and wireless devices no longer connect to the AP. After rebooting (power off wait 30 sec then power on) the AP's will work correctly for another 3-4 hours. I originally had only one of the AP's setup and still experienced the same issue, so I would think it is not a conflict between the devices.
I have downloaded the most recent firmware (same version that was on the AP to begin with) and applied the update... still same problem. I have also reset the AP's (using the reset button on the bottom) and reconfigured them... still same problem.
Anyone have any ideas, experienced or fixed this?

Do you get the same problem by connecting to your router’s wireless network? I believe you need to test that since the APs that you have set up is connected to your router’s network. Try different channels also like 3 and 9.

Similar Messages

Sun x4170 ILOM - Can't get to the web interface 2 days after password reset

Just bought a used x4170. I was able to get iLOM on the network and get to the web interface logon screen after setting the IP for it.
I tried logging on but the password was not given to me. So I connected to the serial interface (rj45) from another machine and used putty to connect. Got to the preboot point and was able to reset the password to default, Rebooted.
I was then able to log into iLOM. That was 2 days ago. Today for some reason, I can't get into iLOM. It pings but I can't get to the web interface. I get the IE error "cannot connect" or unable to connect or something like that.
I'm completely new to this brand of server so consider me completely ignorant on all aspects of the hardware.......lol
Thanks

Hello
By default, you connect to the server’s service processor (SP) using the out-of-band network management port (NET MGT). The ILOM sideband management feature enables you to select either the NET MGT port or one of the server’s Gigabit Ethernet ports (NET 0, 1, 2, 3), which are in-band ports, to send and receive ILOM commands to and from the server SP. In-band ports are also called sideband ports.
You can refer more here : https://docs.oracle.com/cd/E19269-01/820-7959-11/820-7959-11.pdf
If you want to use the NET MGT port of ILOM, then your output should display similar to below
-> show /SP/network
/SP/network
    Targets:
        interconnect
        ipv6
        test
    Properties:
        commitpending = (Cannot show property)
        dhcp_clientid = none
        dhcp_server_ip = xxxxxxxxx
        ipaddress = xxxxxxxxx
        ipdiscovery = dhcp
        ipgateway = xxxxxxxxx
        ipnetmask = xxxxxxxxx
        macaddress = 00:10:E0:65:2F:20
        managementport = MGMT   <<<<<<<<<<<<<<
        outofbandmacaddress = 00:10:E0:65:2F:20
        pendingipaddress = xxxxxxxxx
        pendingipdiscovery = dhcp
        pendingipgateway = xxxxxxxxx
        pendingipnetmask = xxxxxxxxx
        pendingmanagementport = MGMT    <<<<<<<<<<<<
        pendingvlan_id = (none)
        sidebandmacaddress = 00:10:E0:65:2F:21
        state = enabled
        vlan_id = (none)
Hope this helps.
Best Regards
Bhavyesh

Aironet 1100 series web interface times out after few mins of inactivity

Hello,
I just upgraded an Aironet 1121G access point to IOS software version 12.3(8)JEC2 (file name: c1100-k9w7-tar.123-8.JEC2). I noticed that the HTTP web interface now times out after an inactivity of just a few minutes (dont have an exact number, but it times out between 2-4 mins of inactivity). Can this timeout period be changed..!? How? This wasnt happenning on the previous software version: 12.3(8)JEB1.
Also, where can I find the online help files for the latest Cisco IOS software? I cant seem to find it on the Cisco website!
Thanks much for all your help.. really appreciate it.

Does anyone have any idea on this..!? Its terrible having to login every couple of mins..!
Thanks :)

WRVS4400N responds to pings but web interface fails

Hello.
I have a WRVS4400N router in a remote office. I have connectivity to the office and computers there. But the web interface for the router is failing to come up. This happens once every few days or so. Is there any utility or something that I can use to remotely reset the router without making use of the webinterface or having physical access to the router?
It's a version 2 router with the latest firmware.
Thanks.

I gain access via LogMeIn. QuickVPN has not been enabled on this router. And the hardware VPN between it and a like-router in a second office is down and will not come back up.
I know the interface does not come up when I'm physically there because I tried it last time I traveled to the office during the last outage. I am using it's LAN IP 192.168.148.1. I also tried 192.168.148.2. Both IPs respond to pings but no web interface will connect.
The web browser (Chrome, Firefox, and IE) just says "unable to connect" or "cannot display the page"

ASA 5505 configured for WebVPN connecting to Citrix Web Interface

ASA 5505 configured for WebVPN connecting to Citrix Web Interface.
i have a ASA 5505 that I am attempting to configure for WebVPN with passthrough into Web Interface . The user authenticates into WebVPN OK and gets the option to click on the Citrix Link (which is i add bookmark citrix server http:// 172.30.40.5.) i enter the citrix and then for example i want to open to outlook it can not open. (when i want to open some application no application is open)).there is no alarm at asa. how i solve this issue?
thanks.

Teymur,
Can you confim that after disabling the ssl/tls on the Citrix server (secure connectivity) that you are getting exactly the same error. It is possible that it is generating a different error.
The bug where we have see the existing error was CSCtf06303 but that has been fixed in 8.4.1. Can you confirm the exact version of code you are running on the ASA.
If you have confirmed the above two notes it may be adventageous to open a TAC case as we may need to do some live additional troubleshooting.
Thanks
-Jay

Connecting to exchange server via web interface?

Employer's exchange server has IMAP disabled and IT will not consider adding activesync for iPhone 2.0. Using the web interface via Safari is way too hard on an iPhone to be practical except in emergencies.
Question: The new version of Entourage allows for retrieval and sync through a connection to the exchange web interface. It behaves just like it's connected directly to the exchange server, but is hitting exchange's web server.
Is there anything like this for iPhone? Any way to retrieve mail into the native mail application (rather than web app) by polling the exchange web server?

A few things. Neither will give you the functionality you seem to be after.
1) Use Exchange OMA service (text based view via web) very quick compared to the full image web based application. Has read/write functionality but you are not going to want to write an email via this.
2) Outlook 2007 supports http: access. You could use that to pull the data from your work account to say a home PC and sync your iPhone (albeit once a day).
3) Ask them to install iTunes 7.7 on your work PC so you can sync (I think I know how this would go down in a company )

Web Interface doesn't work after installing 11g

A couple days ago I decided to install Oracle 11g (after already having 10g Express Edition), after successfully installing 11g, I tried to access 10g EE using http://127.0.0.1:8080/apex/apex, and it doesn't work anymore. I tried using a java program with Netbeans that connects to my 10g Database and there's connection with no problems and I can upload/download data with no problems, I just can't access the web interface.
Thanks in advance.

jalvarito wrote:
A couple days ago I decided to install Oracle 11g (after already having 10g Express Edition), after successfully installing 11g, I tried to access 10g EE using http://127.0.0.1:8080/apex/apex, and it doesn't work anymore. I tried using a java program with Netbeans that connects to my 10g Database and there's connection with no problems and I can upload/download data with no problems, I just can't access the web interface.
Thanks in advance.And the error message is . . . ????

Error "500 Connection timed out" when starting a Web Interface

Hello,
when starting a Web Interface
(either from preview in Web Interface Builder or directly via transaction BPS_WIF0),
after around 2 minutes I get the following Error Message: "500 Connection timed out"
(in Detail, it says "Connection to partner timed out").
If I use a less complex web interface, this error does not come up.
What can I do to avoid this?
Thank you in advance,
Stephan

Hello Stephan,
if a basic web interface is fast enough, this is normally a confirmation, that the problem does not depend on network performance. We do this test always as an initial test to exclude network issues before we analyze BPS.
So it looks like you do have BPS performance issues. What I can tell you is that multiple variable selectors decrease performance. If this is not you problem I would recommend to check how-to-paper "performance".
It could be related to HTTP-services as well, you will find SAP notes about this topics in OSS.
regards
Eckhard Lewin

After a while, WRT54G won't allow me into web interface anymore.

I can get into the web interface shortly after powering on the router. But after several hours, or days, I no longer can access it. The internet and network continue to work, I just can't access the settings page (I get something like "page cannot be displayed" in all browsers).
If I unplug the router and plug it back in, I can get into the settings page again.
What might cause this? Would it be fixed if I upgrade the firmware?

Hi. I think people are misunderstanding my issue. That'smy fault, as I didn't report the error accurately. The error is actually an "Empty server response", not a 404 page not found. So it's talking to the router, but getting nothing back.
I understand wired connections are not subject to interference, the way wireless ones are.
However a wired connection for this PC is not feasible without bashing holes in the wall,
and anyway I can see no reason why I can't do this wirelessly (even if there's some risk of interference).
Some people seem to be implying this is "By design" and you're expected to access the settings page only via a wire, and it's perfectly normal to require a reboot before being allowed into it. I don't buy that. I've used other routers where I can access the settings wirelessly every time, even if it hasn't been rebooted in a long time.
What I'm getting at is this: the current issue has nothing to do with interference, if it were interference then I could get on after several attempts. Or if the interference is so strong that I can't connect even after trying for hours... then a simple reboot would not fix it. But a reboot does fix it, which tells me the router seems to be holding on to some info or setting that prevents my PC from accessing it. When I reboot, it loses or changes that info/setting. I'm just curious what it might be.
If the bottom line is "your router is old and sucks, replace it" then I can certainly just do that. I'd just like to know that the new one will not have this problem.

WRV200 web interface crashes after changing config

I've got a WRV200 with firmware 1.0.24. Configured to run secured wifi and a VPN tunnel, all without a problem.
Now, when I disable the DHCP service on the box and click Save Settings I'm prompted with the "wifi will restart"message after which the web interface will stop responding. Other functionality (like VPN tunnel) stays OK. I'm connected wired and tried the change with Internet Explorer and Firefox. The only way to get access to the web UI again is do a powercycle of the WRV200. Then the config still shows DHCP enabled.
When trying to upgrade the firmware to 1.0.29 exactly the same happens: try to apply the upgrade, then the web interface stops responding in the end... and after a reboot the f/w still shows 1.0.24.
So: is anyone seeing the same ? And more so: does anyone know how to get around this ?

make sure that you upgrade the firmware from a hardwired computer...
go to ftp://ftp.linksys.com/pub/network and download the tftp.exe file .. assign a static ip address on the computer ( 192.168.1.10 ) and reduce the NIC card's speed to 10 Mbps half duplex mode...
run the tftp.exe file...here the server is router's ip add , password is router's password....browse the firmware file and click upgrade...
the firewall should be disabled during the complete process...
after the firmware upgrade , reset the router for 30 seconds and do a power cycle...

[ACS]Problem web interface after reboot

Hello,
After power outage, when my ACS reboots the web interface doesn't start.
When I connect to CLI with SSH, I enter the command :
sh acs-config-web-interface
This is the result :
ACS management must be running
Please issue 'acs start' CLI if stopped,
or wait for the ACS processes to come up
So I enter the command :
acs start
And it's OK.
What is the reason why the ACS doesn't start properly?
Thank you in advance for your response.
Regards.
Thomas.

Hi Thomas,
Which version of ACS you are running?
Regards
Najaf

Jumbled text in web interface after updating Web Services / firmware

I got a message on the screen of my Officejet 6700:
Update Recommended
An update is available for Web Services (ePrint and Apps).
Do you want to proceed?
I selected Update Now, and it installed fine, or so I thought.
I checked the web interface for the printer, and find there is a bunch of jumbled text, like the code is messed up for the web server.
I had just finished checking the status of ink cartridges (and subsequently replaced one), therefore I fortunately still have the fully functioning webpage open on another machine, so I can tell exactly what the before-and-after is on that one page.
On the Tools > Ink Gauge page, on the good (old) page the table says (title, first row, first column):
Installed Cartridges
Color | Magenta | Cyan | Yellow | Black
Part Number
Type
End-of-Warranty Date (Y-M-D)
First Installation Date (Y-M-D)
Ink Zone
USE
HP
But after updating the software, it says this:
Print Self Test Page
L@S#0456 | Number of Logged Events | L@S#0462 | L@S#0552 | L@S#0450
Accumulated Media Usage
Date
L@S#0477
L@S#0561
L@S#3345
Also, the "Order Supplies" link, with a popup text of "Order printing supplies"
now says "Ink Cartridge", with a popup text of 'Block unwanted faxes"
And "Print Printer Status Report" now says "L@S#2567".
I went to the support section, and found a firmware update, but upon downloading and running it, upon finding the printer, it says it is already Up-to-date, and won't let me select it to try and re-apply the firmware update (as that's evidently what going through the touchscreen menu has already done).
Do I need to just restore to factory settings? I would think firmware wouldn't be changed by doing that. There isn't an old version of the firmware available on the product support page, to revert to an older version.
Via the printer touchscreen menu, a printed Printer Status Report says the firmware version is MPM3CN1322DR.
How do I force a re-install of the firmware, or get them to fix the firmware that was published on 2013-06-25?
This question was solved.
View Solution.

michaelprang,
You are unable to revert back or reinstall the firmware since it has already been downloaded and updated.
Have you attempted to use a different web browser?
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Can't Connect to Web Interface

I have a Valet M10 and I'm trying to connect to the web interace to set up port forwarding. I've tried typing in the 192.168.1.1 address into 2 different browsers but it won't connect. Furthermore when I try and install the Cisco Connect software it gives me an error and won't finish the installation. My wireless works fine but I can't seem to connect to the web interface no matter what I do. Any ideas?

Well the scenario that you explained in that case you can try the following steps:
If you want to make use of the Cisco Connect Software then in that case you need to uninstall the existing Cisco Connect Software Reset the Router, power cycle the whole network and Reinstall the Cisco Connect Software... Then update the firmware of the Router which can be downloaded from the Cisco Website ( homesupport.cisco.com )....
If you want to do it manually then reset the router, power cycle the whole network then check the default gateway address and then try to open the Router setup page..As well as update the firmware of the Router which can be downloaded from the Cisco Website ( homesupport.cisco.com )....

How many connections supports a web interface with each camera and how many Adobe Encoder clients does AMS support? AMS Standart

How many connections supports a web interface with each camera and how many Adobe Encoder clients does AMS support? AMS Standart. We need connect by Adobe Encoder many people. what is differences between Adobe Media Server 5 Professional, Adobe Media Server 5 Standard and Adobe Media Server 5 Extended?

For the detailed list of differences across editions refer this link
http://www.adobe.com/in/products/adobe-media-server-family/buying-guide-comparison.html

Getting dump after pressing save button in web interface

Hi all!
When i press save button in my web interface. i'm getting dump:
The following error text was processed in the system EDW : Syntax error in program GP1ARALDY6TX0M51YNJ5FNELBCI .
The error occurred on the application server kurmutau_EDW_01 and in the work process 0 .
The termination type was: RABAX_STATE
The ABAP call stack was:
Form: VALUE_TO_SID_CONVERT1 of program SAPLRRSI
Form: VALUE_TO_SID_CONVERT1 of program SAPLRRSI
Form: VALUE_TO_SID_CONVERT of program SAPLRRSI
Function: RRSI_VAL_SID_SINGLE_CONVERT of program SAPLRRSI
Form: GET_SID of program GP5VHI3S252BZAWN36WKBAS71QH
Form: GET_DIMID_DA of program GP5VHI3S252BZAWN36WKBAS71QH
Form: WRITEIC of program GP5VHI3S252BZAWN36WKBAS71QH
Form: WRITEIC of program GPEP1KAM5Q04J9717R7T5PDWE0W
Form: APO_WRITEIC of program GPEP1KAM5Q04J9717R7T5PDWE0W
Method: _WRITE_TO_CUBE of program CL_RSDRI_INFOCUBE=============CP
Infocube and web interface were imported from BW3.5 system...
How can i solve this problem?
Thanks in advance...

Go in ST22 and post the short dump to better ubderstand.
Regards

WAP300N No Web interface or Connectivity after 3 - 4 hrs of uptime

Similar Messages

Maybe you are looking for