WAP4410N won't repeat signal

Hi,
we purchased 8 WAP4410N access points to cover our entire school with wireless internet. 2 of those could not have access to a wired network accesspoint, so we wanted those to repeat the signal of 2 others. The ones who are to provide the signal are set up as access points, with the option to allow the signal to be repeated enabled. The mac adress of the other access point is provided, and the channel is set to 6. The 'repeat' 4410N ones are set up as wireless WDS Repeater, with the mac adress of the remote access point entered through the site survey. The channel is also set to 6.
When I connect with the 'repeaters' however, I only get limited access, cannot get on the internet, and I cannot change the network settings in Windows 7 from 'public' to 'business'. Any idea as to what I am doing wrong?
Thanks in advance,
Johan Van Hoeydonck
Belgium

I'm not in front of the wap4410n at the moment, but for sure you can see both wired and wireless mac addresses somewhere in the browser interface.
Otherwise, I imagine they must be listed alongside the serial number on the label under the wap4410n

Similar Messages

I downloaded IOS 7, but reminders' won't repeat when I set them to. They aren't connected to my icloud or an email account. *** is going on??

I downloaded IOS 7, but reminders' won't repeat when I set them to. They aren't connected to my icloud or an email account. *** is going on??

You really shouldn't be using the phone during an update...my thought is that your cables are the root issue. It is possible that because it was in the middle of the imparts and something went wrong it has been "bricked". I'd search the threads for restoring from recovery mode and you might have some luck.

Does Cisco WAP4410N work as repeater for Linksys E4200 ?

Does Cisco WAP4410N work as repeater for Linksys E4200 ?
Hi,
i have Linksys E4200 and I need repeater for it ...
Can anybody help me with this issue ?
BR

Thx for answer
I tested it and it works as Wireless Client - computer connected by ethernet wire is OK, everything works (DHCP etc)
but when i turn on " Allow wireless station to associate" in WAP4410N settings of "Wireless Client/Repeater" it doesn't work at all
I mean clients on wireless side and on wire side too ( DHCP doesnt work , there is no communication )

Keys won't repeat

Downloaded Lion the other day and when I press and hold a key down, it won't repeat. I went into system preferences to 'change key' repeat to fast and 'delay until repeat' to short, but that didn't fix it. And my friend was having the same issue.
So basically, if I want to consecutively repeat a letter, I have to keep pressing it, releasing it, pressing it, etc. Anyone else having the same problem? Any fix to this?

In this thread
https://discussions.apple.com/thread/3190706
got a fix in terminal.
Cheers

Certain keys won't repeat.... really irritating.

It's not a direct inconvenience, mostly just irritating that it's giving me trouble as I only bought it 3 weeks ago. Certain letter keys won't repeat if I hold them down, and I don't know why. Any ideas on how to correct this?

rwright41 wrote:
How do you do a "terminal command"?
Launch the program named "Terminal" (through Launchpad or from the Applications > Utilities folder) and type the command in the window that appears.
Be careful what you do there!
rwright41 wrote:
My daughter is also frustrated about not being able to do multiple exclamation marks and things like that!!!!!!!!!!!!!!!!!!!!! (I'm not on Lion yet, obviously - I can still hold for repeat).
I'm running Mountain Lion, and I can still repeat exclamation points!!!!!!!!!!!!!!!!!!!!! (without that setting). On the other hand, I can't repeat the letter "e" (Eeeeeeeee!!!!!) because it has variants.

How to configure 2 WAP4410n as AP + Repeater

Hi Everyone
I have a problem. We bought 2 WAP4410n-G5 AP for our customer. I'm trying to configure this two AP as:
1- AP as Acces Point (i have tickled the wireless signal can be repeated by repeter)
2- AP as WDS Repeater (i've chosen the AP MAC adress from site survey)
All of them has the same configuration (SSID, password etc). They are in the same network (10.10.10.0). When we are using only first one everything is OK. But i thing there is a problem with the second one. If you are connected by wire to the same network you can open configuration sites from the first and second AP. So those two AP are seeing each other. But when you are nearby the repeater (with laptop) you can connect to the network but you cannot gain IP adress from DHCP. We were trying to configure WEP, WPA, WPA2 TKIP, AES and without any security but there is still a problem. The firmware is the newest from cisco site on both AP (2.0.1.0). And it's not the first couple of AP from Cisco for small business with the same problem. Please help me guys.
And sorry for my bad English.

Hey team,
Just in case ... here is the link to the user guides:
http://www.cisco.com/en/US/products/ps10047/prod_maintenance_guides_list.html
You can open the link and search for repeater. The section relevant starts on the doc page 49.
Do please let us know how you make out. HTH and kindest regards,
Andrew Lissitz

AppleTV won't recognize signal

AppleTV won't recognize WiFi signal. The base is 50 ft. away with 2 walls. Is this too far and if so, can I put a NetGear router connected to the modem with a firewire half way?

Hello hbirkie,
I recommend you take a look at this article named Apple TV (2nd and 3rd generation): Troubleshooting Wi-Fi networks and connections found here http://support.apple.com/kb/TS4546
You can resolve many Wi-Fi issues by checking your network connection settings. You can view or adjust these by selecting Settings > General > Network on Apple TV:
If you discover that you aren't connected to a network, the signal strength is low, or some of these settings are incorrect or blank, try the following steps:
Ensure that Apple TV is within range of your Wi-Fi router or base station.
Confirm that your Wi-Fi router and cable/DSL modem are connected to power and turned on.
Make sure other devices (computers, iPhone, iPad, for example) are able to connect to the Wi-Fi network and access the Internet.
Check your Wi-Fi network settings on Apple TV:
Select Settings > General > Network > Wi-Fi and press the center button on the remote to display nearby networks.
Choose your Wi-Fi network from the list.
If your Wi-Fi network uses a password, make sure you are entering it correctly.
Restart your Apple TV by selecting Settings > General > Restart.
Try restarting your Wi-Fi router or modem by turning it off and then on again.
If possible, connect an Ethernet cable and verify your Internet connection. If you can connect to the Internet using an Ethernet connection, verify that your Apple TV is using the latest software by selecting Settings > General > Software Update. If your Apple TV can be updated, install the update and then try the steps again.If the above steps did not resolve your Wi-Fi issue, click the symptom below to display more detailed troubleshooting steps.
If you're unable to see your Wi-Fi network
Select Settings > General > Network > Wi-Fi and check if you can see any Wi-Fi networks. If you can see other Wi-Fi networks, the issue may be isolated to your Wi-Fi network.
Check for any obstructions and adjust the location of your router or Apple TV; also check for sources ofpotential interference.
If your Wi-Fi network is configured as closed or private, it will not broadcast the network name to Wi-Fi devices.You can join a closed or private network by selecting Settings > General > Network > Wi-Fi > Otherand entering the Wi-Fi network name, security, and password.
Try restarting your Wi-Fi router or modem by turning it off and then on again.
Update your Wi-Fi router to the latest firmware.For an AirPort Base Station, refer to this article for information about firmware updates. For third-party Wi-Fi routers, check the manufacturer's website for details on updating your firmware.
Verify that other devices can see and connect to your Wi-Fi network. If other devices cannot connect to your Wi-Fi network, contact your router manufacturer.
If after attempting the above steps, your Apple TV still cannot see any Wi-Fi networks and other devices are able to see and connect to your Wi-Fi network:
Restart your Apple TV: Select Settings > General > Restart.
If you can connect to the Internet using an Ethernet connection, verify that your Apple TV is using the latest software by selecting Settings > General > Software Update. If your Apple TV can be updated, install the update and test again.
All the best,
Sterling

Tv Won't Detect Signal

I hooked my late 2007 model Macbook up to my Sanyo via Mini DVI to HDMI ports. It worked for a little while, the resolution wasn't 1080p but it nonetheless worked. I started messing with the resolutions, and now my tv won't detect a singal from my computer even though my computer detects the Sanyo. Could I maybe have a faulty Mini DVI to HDMI cable?

Tried it without audigy still with the same result. I also tried a different PSU but that isn't it either and Unless it is the RAM or the CPU (which I doubt). It must be the motherboard. Either my board is faulty or it is just not compatible. I will give my supplier a ring and see what they think.

10.5.2 won't send signal to external projector

Help! I do speaking engagements for a living and just updated to 10.5.2. When I hook an external projector to the computer (DVI to VGA) my MacBook Pro does see the external projector, but will not send a signal to it. It worked yesterday, but as soon as I upgraded it no longer works. We tried a second Mac running 10.5.1 and it worked fine.
I have an engagement Wednesday evening and MUST have this fixed or I will be forced to buy a new computer. Don't have system disks to go backwards with updates. Anybody have any ideas? What a nightmare. I'm desperate to have a computer that will send a video signal out. It sees a monitor, but doesn't see the projector.

Howdy chadnodoubt,
If you are having an issue with your external display not performing as expected when connected with your MacBook Pro, I would suggest that you troubleshoot using the steps in this article -
Apple computers: Troubleshooting issues with video on internal or external displays - Apple Support
Thanks for using Apple Support Communities.
Best,
Brett L

IPhoto slideshow won't repeat

I was quite pleased with myself for being able to pull together this great slideshow on iphoto. However, even though I have the box checked for repeat, I can't get the slideshow to repeat. I have music attached to go with the slide show and the songs stop as soon as the slide show completes. In Settings, I have it so each slide plays for 5 seconds. If I change it to "play slides as long as the music plays", each slide stops for a good 20 seconds (not what I want).
I count just over 100 slides. Is this the problem?

Is this the problem?
Probably. Try adding an audio track(s) of approximately 8 minutes and see if it will repeat.
Then you can try shortening the audio track you've selected in iTune's Info/Options preference pane:
and see if that play you selected tracks and allow repeat at about 5 seconds per slide.
OT

Printer won't receive signal after updating to Yosemite

I have ran a Xerox Phaser 3100 off of my iMac for quite some time and it has been totally fine. I just finished updating to Yosemite and now my printer won't receive anything. Window keeps saying ' Printer 'filter' failure'. I've tried adding and resetting the printer and nothing seems to work. Help!

I have another idea on how to use the old driver. NO guarantees.
For all who may be reading this -- this is for Yosemite -- it reduces security by relaxing sandboxing. It is a workaround, not a permanent fix.
Use the Terminal utility to run the two commands below -
sudo sh -c 'echo "Sandboxing Relaxed" >> /etc/cups/cups-files.conf'
sudo launchctl stop org.cups.cupsd
(sudo means superuser do - this is your admin user on OS X. It asks for your password - but it hides it from you when you type - for security)

Slideshow Won't Repeat in Win7

I have discovered a bug, maybe it's just me, but I don't think so. I have 3 different systems, Win Xp-Pro, Vista, and Win7. On XP-Pro and Vista, the "repeat" function works just fine, multiple pictures just loop over and over. HOWEVER, in Win 7, the repeat function does NOT work. Is anyone else experiencing this within Win7?

I have been experiencing problems with the repeat function on LR3 beta x64 and Win 7 RC1 x64. I haven't tried it on XP or vista.

5s phone won't receive signal after changing sim card

Moved to England; had carrier unlock phone before leaving. Got a new nanoSIM on arrival (specifying 5s). Inserted chip several times, still no signal. What am I missing here?

and you followed this process ?
iPhone: About unlocking

IPod Shuffle won't repeat songs

I can get the same song to repeat when listening on laptop via iTunes in my playlist, but not when I try to listen via my shuffle, even when playing in direct order. Can you set the Shuffle to repeat same song over and over for replay?

I found out the answer to my own question, in case anyone else has this problem. The answer is that the Shuffle will not repeat the same song over and over in a row. Where the other iPods can be programmed via their 'menue' to do so, the Shuffle doesn't have this capability to do so during playback. I got this direct from Apple/iPod support group.

Automated server-based multicast session won't repeat without help

When I set up an ZENWorks Imaging multicast session on a server using
ConsoleOne, the session is no longer checked after the multicast session
runs.
I manage a fairly large school envrironment, and am trying to automate the
process of setting up an unattended daily imaging session in a computer lab
using ZfD 4.01 (fully patched). Wake-on-LAN is working fine, and PXE is
working fine, but the imaging only happens if the checkbox for "Multicast
Sessions Configured for this Server" is checked. Every time it runs, the
checkbox gets UN-checked!!!! AAARRRGGGHHH!!!!
The whole point of doing this is to eliminate the need for manual
intervention! I've never seen this issue discussed anywhere, and it's
driving me nuts. Is there a place I'm overlooking where this can be
changed?
Thanks,
Roger

How would one go about doing the LDAP thing?
Thanks,
Roger
"Marcus Breiden" <[email protected]> wrote in message
news:1qk3gk7uuaq4d$.[email protected]. .
> On Mon, 08 Jan 2007 19:53:11 GMT, Roger Kresge wrote:
>
> > The whole point of doing this is to eliminate the need for manual
> > intervention! I've never seen this issue discussed anywhere, and it's
> > driving me nuts. Is there a place I'm overlooking where this can be
> > changed?
>
> nope, only option is either to use ldap or similar to set the checkbox
back
> or to get zwake from www.engl.co.uk
>
> --
>
> If you have already compiled drivers or have linux.2 please put them on
> http://forge.novell.com/modules/xfmo...ect/?zfdimgdrv
> Live BootCd and USB Disk from Mike Charles
> http://forge.novell.com/modules/xfmod/project/?imagingx
> eZie http://forge.novell.com/modules/xfmod/project/?ezie
>
> Marcus Breiden
>
> If you are asked to email me information please change -- to - in my
e-mail
> address.
> The content of this mail is my private and personal opinion.
> http://www.edu-magic.net

WAP4410N won't repeat signal

Similar Messages

Maybe you are looking for