White screen after downloading Yosemite

i downloaded Yosemite on my MacBookPro and when it rebooted I just got a white screen. Can't even turn it off

Hi PG1892,
If your Mac is starting up to a white or grey screen after upgrading to Yosemite, you may find the troubleshooting steps outlined in the following article helpful:
Mac OS X: Gray screen appears during startup
Regards,
- Brenden

Similar Messages

I have a white screen whilst downloading Yosemite onto my Mac. What should I do??

I Have a white screen after downloading & installing Yosemite. What should I do now???

First of all, wait and give it some time. It might be rebuilding the disk. Sometimes, it takes a little time for the busy indicator to come up.
If there is no change in 5 min., reboot with the option key pressed. This will make the mountable recovery partition visible. You can select it and boot into it, then use Disk Utlity to try to check and repair your boot volume.
If there is no recovery HD, boot while pressing CMD-R. You need to be in a place with a network connected to the internet. If you are, you can boot recovery tools over the internet, and restore your system. Depending on the speed of your network connection, this can take a while (even hours....).
It is useful to have a backup of your system using a USB drive. These are inexpensive. Use Carbon Copy Cloner to maintain a copy of your main disk. You can boot from the USB drive, and repair your internal volume, and even completely restore it, should trouble arise.

White screen after installing yosemite

I was upgrading to yosemite and when i restarted my computer i am stuck on a blank white screen. i have tried all of the resets available and nothing is working. Any insight?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Why am I getting a white screen after downloading to OSX Mountain lion from OSX Snow Leopard. What caused this?

I just upgraded to OSX Mountain Lion from OSX Snow Leopard, thinking this was the thing to do. I have NEVER had any problems with Snow Leopard, but
after just a few days after downloading OSX Mountain Lion when I turned the computer on, the screen was white. Stayed white. I had to go onto another
computer to find out what to do. What caused this and will this happen again?

Did you see a circle made of light grey hash marks in the center/bottom of the screen? My iMac is 5 years old and for every update until 10.8.2 I would get the same white screen and the first few times I paniced and thought the machine was broken! Just let it play out until the desktop comes back up and it should not do it again until you do a system update.

IMac suddenly shows white screen after update Yosemite to 10.10.1

The day after I installed the update(10.10.1) for Yosemite, regularly my iMac suddenly stops working by showing a white screen. After 10 seconds, the iMac reboots automatically and again shows a white screen. Than, it stops. No action. No noise. I'm always obliged to stop the iMac by pressing the start button and restarting by holding the 'shift' key otherwise I have to look at a white screen again! In the save modus, I can work(typing this story) and restart the iMac. After a while, the whole show starts again. What can I do? Installing Yosemite again and whiteout the update? Can I undo the update? This once, I made no backup before the update(Murphy's law). Any suggestion will do!

Try these in order testing your system after each to see if it's back to normal:
1. a. Resetting your Mac's PRAM and NVRAM
    b. Intel-based Macs: Resetting the System Management Controller (SMC)
2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
4. Reinstall Yosemite: Reboot from the Recovery HD. Select Reinstall OS X from the Utilities menu, and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.
5. Reinstall Yosemite from Scratch:
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
How to Clean Install OS X Yosemite
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.

White screen after downloading iOS6 update

I just downloaded the iOS6 update onto my iPod touch, 4th generation. (I was prompted to do so when I turned it on this afternoon.) The update "stuck" midway, and after waiting more than an hour, I forced the iPod to turn off by holding down the sleep/wake button and the home button simultaneously. The iPod shut down and then restarted itself. However, the restart left me with a white/blank screen. Is there any way I can restore this iPod to factory defaults? It does not appear as a device in iTunes.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Blank white screen after download

I have downloaded and run the CC trial, but when I open CC from my desktop the window is blank white when it should be the screen where I select which trial to install. I have deleted the CC and redownloaded it twice to no avail. Any suggestions?

Hi,
Please refer to the threads below where this issue has been addressed:
New Creative Cloud App unusable: it's blank!
creative cloud is blank window why?
Cloud Desktop App is blank?
Re: Creative Cloud app opening blank
Regards,
Sheena

White screen after downloading adobe flash player

was told by odobe to download the latest flash player, which i thought at the time, i done ok, but now i sign on, all i get is a white flashing screen, my icons have all gone, i cant even get onto the internet now,
strange thing, once i sign on, i get locked out ?
is there any way i can uninstall the odobe from my lap top, even throught i cant actually use my lap top,
i really would appricate any help, anyone could possibly give me,

Check
http://forums.adobe.com/thread/885448
http://forums.adobe.com/thread/867968

What to do with withe screen after download ios5

my iphone turnd on white screen after download ios 5 what can i do now

If you purchased apple care plus then you can get your iPad replaced for a $49 service fee. If you didn't then out of warranty replacements start at 219 for a mini and goes up to 299 for the newer models.
If you decide to take it to a non-authorized repair place, they might fix it cheaper, but once a non-authorized place touches your device Apple washes its hands of it and will have nothing else to do with it.
So it kinda comes down to the more expensive sure bet of an out of warranty replacement or a cheaper gamble

My MacBook Pro won't go beyond a white screen, after I pushed the restart button. How can I get it to a login? I have routinely backed it up, but don't know how to bring that up, nor if I have a boot file on that external disk. Help!

My MacBook Pro won't go beyond a white screen, after I pushed the restart button. How can I get it to a login? I have routinely backed it up, but don't know how to bring that up, nor if I have a boot file on that external disk. Help!

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

After downloading yosemite, can't import photos from camera to iPhoto

After downloading Yosemite 10.10.1 to my Macbook Air, I can't import photos from camera to iPhoto. Had no problem before. It recognizes camera and says loading, but it never does load photos.

That's the latest version.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
The title of the Console window should be All Messages. If it isn't, select
SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar at the top of the screen. Click the Clear Display icon in the toolbar. Then take the actions that you're having trouble with. Select any messages that appear in the Console window. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
The log contains a vast amount of information, almost all of which is irrelevant to solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Some private information, such as your name, may appear in the log. Anonymize before posting.

TS3824 My MacBook Pro freezes with a white screen after I log in.

MacBook Pro freezes with a white screen after I log in, support says to download an update, but if it
s frozen, how do I update?

Thanks for posting back your solution. It will help others w/the same problem.

IMac will not boot. Stuck at white screen after chime.

I am starting a new thread this because it seems that other people with this problem are able to get their Macs working with some sort of keyboard combination on boot. I am not. Nothing is working. My computer is currently a 27 inch brick... Actually a lamp, since it is frozen on a really nice white screen.....
Installed Yosemite on my 27" iMac (early 2010, i7) when Yosemite came out a couple weeks ago. Everything was working fine but it wouldn't read my external drive, so I did a reboot. After the reboot, it freezes on the white screen after the chime. No keyboard combinations work to get it to do anything....also, if I hit the power button it shuts off immediately.
Nothing is working to get it moving. And yes, I am using a usb keyboard, not the Bluetooth, to try to hit any of the keyboard combinations posted in various discussions.
My AppleCare is expired, so I'm going to be very upset if I have to go pay to have Apple fix their problematic software. Any help you guys can give will be greatly appreciated.
Thank you,

See if you can boot into the Safe Mode using your normal account. Disconnect all peripherals except those needed for the test. Shut down the computer and then power it back up after waiting 10 seconds. Immediately after hearing the startup chime, hold down the shift key and continue to hold it until the gray Apple icon and a progress bar appear and again when you log in. The boot up is significantly slower than normal. This will reset some caches, forces a directory check, and disables all startup and login items, among other things. When you reboot normally, the initial reboot may be slower than normal. If the system operates normally, there may be 3rd party applications which are causing a problem. Try deleting/disabling the third party applications after a restart by using the application un-installer. For each disable/delete, you will need to restart if you don’t do them all at once.
Safe Mode - Mavericks
Safe Mode - About
Startup - Gray, Blue or White screen at boot, w/spinner/progress bar
Startup - Gray Screen
Startup Issues - Resolve
Startup Issues - Resolve (2)

How do i get out of white screen after login

How do i get out of the white screen after signing on to my computer.

Hi GregConk,
Thank you for visiting Apple Support Communities.
If I understand right, your iMac is only starting up to a blank white screen after you log in. If so, there are some good troubleshooting steps that may resolve this behavior.
First, try booting your computer into Safe Mode, to see if your desktop appears in this mode:
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Start your Mac, then immediately hold the Shift key. This performs a Safe Boot. Advanced tip: If you want to see the status of a Safe Boot as it progresses, you can hold Shift-Command-V during start up (instead of just Shift).
Note: A Safe Boot takes longer than a typical start up because it includes a disk check and other operations.
If your Mac starts up as expected, immediately try restarting.
From:
Mac OS X: Gray screen appears during startup - Apple Support
If you see your desktop in Safe Mode, but not when starting up normally, try the troubleshooting tips in this article next:
OS X Yosemite: If you think you have incompatible login items
Best Regards,
Jeremy

Why is my MBP (2011) so slow after downloading yosemite?

My MBP has basically become unusable after downloading yosemite a few days ago. It is incredibly slow, and I get the pinwheel for hours on end. I have tried restarting the computer countless time. Although my account is really slow and inoperable, I can use the internet on my guest account without any problems. The issue seems to be specific to my account/data.
Any ideas what this might be? Is it an encryption issue? How long does it take? Can I stop it?
Thanks!

It's only related to encryption if you are using it.
Try these in order testing your system after each to see if it's back to normal:
1. a. Resetting your Mac's PRAM and NVRAM
    b. Intel-based Macs: Resetting the System Management Controller (SMC)
2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
     Boot to the Recovery HD: Restart the computer and after the chime press and hold down the
     COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the
     computer and after the chime press and hold down the OPTION key until the boot manager
     screen appears. Select the Recovery HD and click on the downward pointing arrow button.
3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
4. Reinstall Yosemite: Reboot from the Recovery HD. Select Reinstall OS X from the Utilities menu, and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.
5. Reinstall Yosemite from Scratch:
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
How to Clean Install OS X Yosemite
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.

White screen after downloading Yosemite

Similar Messages

Maybe you are looking for