Will a 2 port LAG setup between 2 cisco 200-50s create routing issues?

I followed this guide. http://sbkb.cisco.com/CiscoSB/GetArticle.aspx?docid=caae365b755f46f5989177cb68216304_Link_Aggregation_on_Cisco_Series_Managed_Switches.xml&pid=2&converted=0 and linked ports 2 and 26 on both switches. Outside IT staff seems to think this will cause routing issues if multiple vlans are not involved.

Hello,
VLANs are not required for LAGs to function properly. Once you configure the LAG members you can configure the LAG as a trunk port with multiple VLANs, and access port with just one, or even a routed port with an IP address on it.
As long as both sides of the LAG are configured the same way there won't be an issue. Since these switches are Layer 2 only, they don't even do any kind of routing, so your outside IT may have meant a layer 2 loop, which will happen with multiple connections between the same switches. But when you configure them as a LAG is treats those links as the same connection, so there is no layer 2 loop either.
Hope that helps,
Christopher Ebert - Advanced Network Support Engineer
Cisco Small Business Support Center
*please rate helpful posts*

Similar Messages

Cisco Linksys E1500 Wireless Router Issues

About a month ago, I bought this new router, and at first it seemed like it was working okay, but then i started noticing that my roku box (watch netflix) was cutting out all the time, losing the connection from the new router. I also began to notice that if more than one person was online, pages took forever to load, can't watch youtube videos and even listening to music online like Pandora became difficult. Also it says that I can get up to 300 mbps but when i run the test I get .50 download and about 1.8 upload
Details About Router & Connection
Its a Linksys E1500 with the capability of up to 6 devices and my IPS is Comcast.

Make sure to upgrade the router’s firmware if there is a new firmware update available. Try to play around with the router’s wireless settings; use this tool: http://www.metageek.net/products/inssider/ to select the best channel that you can set on your router. With regard to that 300 Mbps of speed, it means that it is the maximum link/card speed that the adapter could get from the router not the actual internet speed.

Call/video not working between Cisco jabber for Windows and VCS control C40s

Hello,
I've been struggling with no luck how to make a call using Cisco Jabber for Windows 9.6.0 registered to CM 8.6.2 with intercluster ICT to another CM 8.6.2 where we have a VCS Control 7.0.2 via GK H225, and all C40s are registered as H.323.
The VCS has interworking between H323 and SIP, however not sure if there is any problem with that. Assuming it is ok, not sure either if I'm facing any interoperability issue because in my remote site I have C40 (H323 registered at VCS and SIP listening mode) and cisco jabber for windows which is SIP based.
If is not possible, would I be able to change my C40 from H323 to SIP at VCS, or have both H323/SIP registered at VCS? If so, will I need to change as well instead of GK I'll have to establish a SIP Trunk between the CM and VCS?
Another thing I do not believe either I would be able to have one VCS connected with two clusters, right?
I'm just trying to find a solution in case my current topology is not compatible, but feel free if you have any better idea to make it work.
Anyway here is what is happening:
When I make a call from my cisco jabber windows to C40 using alias number. The call is being redirected just fine to the C40 and it rings, however when someoene or the auto answer picks it up, the call dropped right away.
However, if I enabled the MTP in my CSF device, the call gets longer before dropping. I was even able to see my jabber " start video" turns green, before was grayed out all the time and the call dropped faster. I hear a fast busy tone.
I'm able to provide SDI traces, logs, diagnostic sip/h323 calls from VCS in order to know for sure if this is an incompatible issue or something I can workaround.
Let me know if someone of you are interested in read these logs or could point me on the right direction.
Thanks!

Ok,
I have looked at both logs. I have to mentinon though that you didnt
provide the log that shows the h323 setup between cucm and the VCS. This
is most likely because the call originated from a different cucm than
the ones you provided the logs from.
The call would have orginated from the first cucm in the cucm group of
this trunk: Name=RL_TRUNK_VIDEO
The cucm ip will be : 10.252.53.10.
This is the VCS log that confirms where the h323 request originated
from:
pr 10 22:50:29 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:29,187"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="54000"
Received RAS PDU:
Having said that here is my analysis of the logs that you sent..
Jabber sent an INVITE to CUCM and advertised all the codecs (audio and
video it can support)..
Observer that Jabber says it doesnt support G729 anexB
21:55:16.576 |//SIP/SIPTcp/wait_SdlReadRsp: Incoming SIP TCP message
from 10.223.20.73 on port 54677 index 90661 with 2220 bytes:
[862370,NET]
INVITE sip:[email protected];user=phone SIP/2.0
Via: SIP/2.0/TCP 10.223.20.73:54677;branch=z9hG4bK000029d3
From: "4122107" <sip:[email protected]>;tag=00059a3c78000011000070b0
-00000e65
To: <sip:[email protected]>
Call-ID: [email protected]
Max-Forwards: 70
Date: Fri, 11 Apr 2014 01:55:16 GMT
CSeq: 101 INVITE
User-Agent: Cisco-CSF/9.4.1
m=audio 19252 RTP/AVP 0 8 18 105 104 101
c=IN IP4 10.223.20.73
a=rtpmap:0 PCMU/8000
a=rtpmap:8 PCMA/8000
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=no
a=rtpmap:105 G7221/16000
a=fmtp:105 bitrate=24000
a=rtpmap:104 G7221/16000
a=fmtp:104 bitrate=32000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=sendrecv
m=video 28878 RTP/AVP 97
c=IN IP4 10.223.20.73
++++Now lets observer the capabilites exchange during h245 negotiation
between cucm and VCS++++
Here CUCM advertises its caps to VCS (afterreceiving caps from VCS)
Note that G729A, G729AB, G729 is all advertised..
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,017"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : terminalCapabilitySet
capabilityTableEntryNumber 2,
       capability receiveAudioCapability :
g729wAnnexB : 6
       capabilityTableEntryNumber 3,
   capability receiveAudioCapability : g729AnnexAwAnnexB : 6
       capabilityTableEntryNumber 4,
       capability
receiveAudioCapability : g729 : 6
capabilityTableEntryNumber 5,
       capability receiveAudioCapability :
g729AnnexA : 6
++++++
After doing MSD (master slave determination, we move to the OLC phas e..
Here we see that the far end..c40 wants to use G729AB for media++++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,783"
Module="network.h323" Level="DEBUG": Src-ip="10.224.114.11" Src-
port="11163"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
+++Next VCS sends G729AB as the codec to use to CUCM+++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,784"
Module="network.h323" Level="DEBUG": Dst-ip="10.252.53.10" Dst-
port="45660"
Sending H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
++++The next thing we get is an OLC reject from CUCM and this is where
th call drops++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= response : openLogicalChannelReject :
forwardLogicalChannelNumber 1,
   cause dataTypeNotSupported : NULL
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="INFO": Dst-ip="10.224.114.11" Dst-
port="11163"
Detail="Sending H.245 OpenLogicalChannelRejResponse
+++We then receive a call release from cucm with cause code of 47:
resource unavailable++++
Apr 10 22:50:32 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:32,365"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="50913"
Received H.225 PDU:
Q931
   Message Type: Release
Complete
   Call reference flag: Message sent from originating side
Call reference value: 0x7b
   Info Element : Cause
     Location: Usr
   Cause Value: Resource unavailable
   Info Element : User User
   Length = 22
Suggestions:
Change the region setting between the ICT trunk to VCS and Jabber to use
G711 and test again.

How to create routed port in Cisco SF-300 Switch

I am trying to create routed ports in SF 300 small business 8 port switch.
I have 3 different LAN say 192.168.1.0/24, 192.168.2.0/24 and 192.168.3.0/24
I have 3 unmanaged linsys switch where I have connected all these computers.
Now what I have to do is to create routed ports in SF300 and route this networks properly.
Can anybody help me on this? Thanks in advance.

Dear Shereef,
Thank you for reaching Small Business Support Community.
In Layer 3 system mode, the device can have multiple IP addresses. Each IP address can be assigned to specified ports, LAGs, or VLANs. Operating in Layer 3 mode, the device routes traffic between the directly attached IP subnets configured on the device. In addition, you can manually define default routes.
Configuring the device to work in Layer 3 mode is performed in the Administration >System Settings page.
To define IP addresses on the ports:
IP Configuration > IPv4 Management and Interfaces > IPv4 Interface
To define an IP static route:
Click IP Configuration > IPv4 Management and Interfaces > IPv4 Routes
Just in case you can check on the admin guide, chapter 16 for a more detailed step by step description;
http://www.cisco.com/en/US/docs/switches/lan/csbms/sf30x_sg30x/administration_guide/78-19308-01.pdf
I hope you find this information useful and please do not hesitate to reach me back if there is any further assistance I may help you with.
Kind regards
Jeffrey Rodriguez S. .:|:.:|:.
Cisco Customer Support Engineer
*Please rate the Post so other will know when an answer has been found.

Site-to-Site VPN between Cisco ASA 5505 (8.4) and Cisco Router (IOS 15.2)

Hi, I'm trying to create Site-to-Site VPN between Cisco ASA 5505 and Cisco Router 3945.
I've tried create configuration with and without ASA wizard, but anyway it doesn't work.
Please help me to find where is the issue.
I have two sites and would like to get access from 192.168.83.0 to 192.168.17.0
192.168.17.0 --- S1.S1.S1.S1 (IOS Router) ==================== S2.S2.S2.S2 (ASA 5505) --- 192.168.83.0
Here is my current configuration.
Thanks for your help.
IOS Configuration
version 15.2
crypto isakmp policy 1
encr aes 256
authentication pre-share
group 2
crypto isakmp key cisco address 198.0.183.225
crypto isakmp invalid-spi-recovery
crypto ipsec transform-set AES-SET esp-aes esp-sha-hmac
mode transport
crypto map static-map 1 ipsec-isakmp
set peer S2.S2.S2.S2
set transform-set AES-SET
set pfs group2
match address 100
interface GigabitEthernet0/0
ip address S1.S1.S1.S1 255.255.255.240
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map static-map
interface GigabitEthernet0/1
ip address 192.168.17.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
access-list 100 permit ip 192.168.17.0 0.0.0.255 192.168.83.0 0.0.0.255
ASA Configuration
ASA Version 8.4(3)
interface Ethernet0/0
switchport access vlan 2
interface Vlan1
nameif inside
security-level 100
ip address 192.168.83.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address S2.S2.S2.S2 255.255.255.248
ftp mode passive
same-security-traffic permit intra-interface
object network inside-network
subnet 192.168.83.0 255.255.255.0
object network datacenter
host S1.S1.S1.S1
object network datacenter-network
subnet 192.168.17.0 255.255.255.0
object network NETWORK_OBJ_192.168.83.0_24
subnet 192.168.83.0 255.255.255.0
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any log
access-list outside_cryptomap extended permit ip 192.168.83.0 255.255.255.0 object datacenter-network
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn_pool 192.168.83.200-192.168.83.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic inside-network interface
nat (inside,outside) source static inside-network inside-network destination static inside-network inside-network no-proxy-arp route-lookup
nat (inside,outside) source static inside-network inside-network destination static datacenter-network datacenter-network no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.83.0_24 NETWORK_OBJ_192.168.83.0_24 destination static datacenter-network pdatacenter-network no-proxy-arp route-lookup
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 DEFAULT_GATEWAY 1
crypto ipsec ikev1 transform-set vpn-transform-set esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set vpn-transform-set mode transport
crypto ipsec ikev1 transform-set L2L_SET esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set L2L_SET mode transport
crypto dynamic-map dyno 10 set ikev1 transform-set vpn-transform-set
crypto map vpn 1 match address outside_cryptomap
crypto map vpn 1 set pfs
crypto map vpn 1 set peer S1.S1.S1.S1
crypto map vpn 1 set ikev1 transform-set L2L_SET
crypto map vpn 20 ipsec-isakmp dynamic dyno
crypto map vpn interface outside
crypto isakmp nat-traversal 3600
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
group-policy GroupPolicy_S1.S1.S1.S1 internal
group-policy GroupPolicy_S1.S1.S1.S1 attributes
vpn-tunnel-protocol ikev1
group-policy remote_vpn_policy internal
group-policy remote_vpn_policy attributes
vpn-tunnel-protocol ikev1 l2tp-ipsec
username artem password 8xs7XK3To4s5WfTvtKAutA== nt-encrypted
username admin password rqiFSVJFung3fvFZ encrypted privilege 15
tunnel-group DefaultRAGroup general-attributes
address-pool vpn_pool
default-group-policy remote_vpn_policy
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group S1.S1.S1.S1 type ipsec-l2l
tunnel-group S1.S1.S1.S1 general-attributes
default-group-policy GroupPolicy_S1.S1.S1.S1
tunnel-group S1.S1.S1.S1 ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f55f10c19a0848edd2466d08744556eb
: end

Thanks for helping me again. I really appreciate.
I don't hve any NAT-exemptions in Cisco IOS Router. Transform-set I will change soon, but I've tried with tunnel mode and it didn't work.
Maybe NAT-exemptions is the issue. Can you advice me which exemptions should be in Cisco IOS Router?
Because on Cisco ASA I guess I have everything.
Here is show crypto session detail
router(config)#do show crypto session detail
Crypto session current status
Code: C - IKE Configuration mode, D - Dead Peer Detection
K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
X - IKE Extended Authentication, F - IKE Fragmentation
Interface: GigabitEthernet0/0
Session status: DOWN
Peer: 198.0.183.225 port 500 fvrf: (none) ivrf: (none)
      Desc: (none)
      Phase1_id: (none)
IPSEC FLOW: permit ip 192.168.17.0/255.255.255.0 192.168.83.0/255.255.255.0
        Active SAs: 0, origin: crypto map
        Inbound: #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0
        Outbound: #pkts enc'ed 0 drop 0 life (KB/Sec) 0/0
Should I see something in crypto isakmp sa?
pp-border#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst             src             state          conn-id status
IPv6 Crypto ISAKMP SA
Thanks again for your help.

S2S between Cisco ASA 5505 and Sonicwall TZ-170 but not able to ping across

Hi,
I am helping out a friend of mine with his Site-to-Site VPN between his companies Cisco ASA another company's SonicWall TZ-170. I have checked the screenshots proivded by the other end and tried to match with ours. The Tunnel shows but we are not able to Ping resources on the other end. The other side insists that the problem is on our end but I am not sure where the issue resides. Please take a look at our config and let me know if there is anything that I have missed. I am pretty sure I didn't but extra eyes may be of need here.
Our LAN is 10.200.x.x /16 and theirs is 192.168.9.0 /24
ASA Version 8.2(2)
terminal width 300
hostname company-asa
domain-name Company.com
no names
name 10.1.0.0 sacramento-network
name 10.3.0.0 irvine-network
name 10.2.0.0 portland-network
name x.x.x.x MailLive
name 192.168.9.0 revit-vpn-remote-subnet
dns-guard
interface Ethernet0/0
nameif outside
security-level 0
ip address x.x.x.x 255.255.255.128
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.200.200.1 255.255.0.0
interface Ethernet0/2
nameif dmz
security-level 50
ip address 172.22.22.1 255.255.255.0
interface Ethernet0/3
description Internal Wireless
shutdown
nameif Wireless
security-level 100
ip address 10.201.201.1 255.255.255.0
interface Management0/0
shutdown
nameif management
security-level 100
no ip address
management-only
boot system disk0:/asa822-k8.bin
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
dns domain-lookup outside
dns server-group DefaultDNS
domain-name company.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network local_net_group
network-object 10.1.0.0 255.255.0.0
network-object 10.2.0.0 255.255.0.0
network-object 10.200.0.0 255.255.0.0
network-object 10.3.0.0 255.255.0.0
network-object 10.4.0.0 255.255.0.0
network-object 10.5.0.0 255.255.0.0
network-object 10.6.0.0 255.255.0.0
network-object 10.7.0.0 255.255.0.0
network-object 192.168.200.0 255.255.255.0
object-group network NACIO123
network-object 1.1.1.1 255.255.255.224
object-group service MAIL_HTTPS_BORDERWARE tcp
port-object eq smtp
port-object eq https
port-object eq 10101
object-group service SYSLOG_SNMP_NETFLOW udp
port-object eq syslog
port-object eq snmp
port-object eq 2055
object-group service HTTP_HTTPS tcp
port-object eq www
port-object eq https
object-group network OUTSIDECO_SERVERS
network-object host x.x.x.34
network-object host x.x.x.201
network-object host x.x.x.63
object-group network NO-LOG
network-object host 10.200.200.13
network-object host 10.200.200.25
network-object host 10.200.200.32
object-group service iPhoneSync-Services-TCP tcp
port-object eq 993
port-object eq 990
port-object eq 998
port-object eq 5678
port-object eq 5721
port-object eq 26675
object-group service termserv tcp
description terminal services
port-object eq 3389
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service DTI tcp
description DCS CONTROL PROTOCOL
port-object eq 3333
object-group service H.245 tcp
description h.245 signaling
port-object range 1024 4999
object-group service RAS udp
port-object eq 1719
port-object range 1718 1720
object-group service XML tcp
port-object range 3336 3341
object-group service mpi tcp
port-object eq 2010
object-group service mvp_control tcp
port-object eq 2946
object-group service rpc tcp-udp
port-object eq 1809
object-group service tcp8080 tcp
port-object eq 8080
object-group service tcp8011 tcp
port-object eq 8011
object-group service rtp_rtcp_udp udp
port-object range 1024 65535
object-group service ecs_xml tcp-udp
port-object eq 3271
object-group service rtp20000 udp
description 10000-65535
port-object range 20000 25000
port-object range 10000 65535
object-group service tcp5222 tcp
port-object range 5222 5269
object-group service tcp7070 tcp
port-object eq 7070
object-group network videoco
network-object host x.x.x.144
network-object host x.x.x.145
object-group service video tcp
port-object range 1718 h323
object-group service XML2 tcp-udp
port-object range 3336 3345
object-group service tcp_tls tcp
port-object eq 5061
object-group service Autodesk tcp
port-object eq 2080
port-object range 27000 27009
access-list outside_policy remark ====== Begin Mail From Postini Network ======
access-list outside_policy extended permit tcp x.x.x.x 255.255.240.0 host x.x.x.x eq smtp
access-list outside_policy extended permit tcp x.x.x.x 255.255.255.240 host x.x.x.x eq smtp
access-list outside_policy extended permit tcp x.x.x.0 255.255.240.0 host x.x.x.x eq smtp
access-list outside_policy remark ****** End Mail From Postini Network ******
access-list outside_policy remark ====== Begin Inbound Web Mail Access ======
access-list outside_policy extended permit tcp any host x.x.x.x object-group HTTP_HTTPS
access-list outside_policy remark ****** End Inbound Web Mail Access ******
access-list outside_policy remark ====== Begin iPhone Sync Rules to Mail Server ======
access-list outside_policy extended permit tcp any host x.x.x.x object-group iPhoneSync-Services-TCP
access-list outside_policy remark ****** End iPhone Sync Rules to Mail Server ******
access-list outside_policy remark ====== Begin MARS Monitoring ======
access-list outside_policy extended permit udp x.x.x.x 255.255.255.128 host x.x.x.x object-group SYSLOG_SNMP_NETFLOW
access-list outside_policy extended permit icmp x.x.x.x 255.255.255.128 host x.x.x.x
access-list outside_policy remark ****** End MARS Monitoring ******
access-list outside_policy extended permit tcp object-group NACIO123 host x.x.x.141 eq ssh
access-list outside_policy extended permit tcp any host x.x.x.x eq www
access-list outside_policy extended permit tcp any host x.x.x.x eq https
access-list outside_policy extended permit tcp any host x.x.x.x eq h323
access-list outside_policy extended permit tcp any host x.x.x.x range 60000 60001
access-list outside_policy extended permit udp any host x.x.x.x range 60000 60007
access-list outside_policy remark radvision 5110   port 80 both
access-list outside_policy extended permit object-group TCPUDP any object-group videoco eq www
access-list outside_policy remark radvision
access-list outside_policy extended permit tcp any object-group videoco object-group termserv
access-list outside_policy remark radvision 5110 port21 out
access-list outside_policy extended permit tcp any object-group videoco eq ftp
access-list outside_policy remark rad5110   port22 both
access-list outside_policy extended permit tcp any object-group videoco eq ssh
access-list outside_policy remark rad 5110 port161 udp both
access-list outside_policy extended permit udp any object-group videoco eq snmp
access-list outside_policy remark rad5110 port443 both
access-list outside_policy extended permit tcp any object-group videoco eq https
access-list outside_policy remark rad5110 port 1024-4999 both
access-list outside_policy extended permit tcp any object-group videoco object-group H.245
access-list outside_policy remark rad5110 port 1719 udp both
access-list outside_policy extended permit udp any object-group videoco object-group RAS
access-list outside_policy remark rad5110 port 1720 both
access-list outside_policy extended permit tcp any any eq h323
access-list outside_policy remark RAD 5110 port 3333 tcp both
access-list outside_policy extended permit tcp any object-group videoco object-group DTI
access-list outside_policy remark rad5110 port 3336-3341 both
access-list outside_policy extended permit object-group TCPUDP any object-group videoco object-group XML2
access-list outside_policy remark port 5060 tcp/udp
access-list outside_policy extended permit object-group TCPUDP any object-group videoco eq sip
access-list outside_policy remark rad 5110port 1809 rpc both
access-list outside_policy extended permit object-group TCPUDP any object-group videoco object-group rpc
access-list outside_policy remark rad 5110 port 2010 both
access-list outside_policy extended permit tcp any object-group videoco object-group mpi
access-list outside_policy remark rad 5110 port 2946 both
access-list outside_policy extended permit tcp any object-group videoco object-group mvp_control
access-list outside_policy extended permit tcp any object-group videoco object-group tcp8080
access-list outside_policy extended permit tcp any object-group videoco object-group tcp8011
access-list outside_policy remark 1024-65535
access-list outside_policy extended permit udp any object-group videoco object-group rtp_rtcp_udp
access-list outside_policy extended permit object-group TCPUDP any object-group videoco object-group ecs_xml
access-list outside_policy extended permit udp any object-group videoco object-group rtp20000
access-list outside_policy extended permit tcp any object-group videoco eq telnet
access-list outside_policy remark port 53 dns
access-list outside_policy extended permit object-group TCPUDP any object-group videoco eq domain
access-list outside_policy remark 7070
access-list outside_policy extended permit tcp any object-group videoco object-group tcp7070
access-list outside_policy remark 5222-5269 tcp
access-list outside_policy extended permit tcp any object-group videoco range 5222 5269
access-list outside_policy extended permit tcp any object-group videoco object-group video
access-list outside_policy extended permit tcp any object-group videoco object-group tcp_tls
access-list outside_policy remark ====== Begin Autodesk Activation access ======
access-list outside_policy extended permit tcp any any object-group Autodesk
access-list outside_policy remark ****** End Autodesk Activation access ******
access-list outside_policy extended permit tcp x.x.x.x 255.255.255.248 host x.x.x.x eq smtp
access-list outside_policy remark ****** End Autodesk Activation access ******
access-list inside_policy extended deny tcp host 10.200.200.25 10.1.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny tcp host 10.200.200.25 10.3.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny tcp host 10.200.200.25 10.2.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny tcp host 10.200.200.25 10.4.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny tcp host 10.200.200.25 10.5.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny udp object-group NO-LOG any eq 2967 log disable
access-list inside_policy extended deny tcp object-group NO-LOG any eq 2967 log disable
access-list inside_policy remark ====== Begin Outbound Mail Server Rules ======
access-list inside_policy extended permit udp host 10.200.200.222 any eq 5679
access-list inside_policy extended permit tcp host 10.200.200.222 any eq smtp
access-list inside_policy remark ****** End Outbound Mail Server Rules ******
access-list inside_policy extended permit ip object-group local_net_group any
access-list inside_policy extended permit icmp object-group local_net_group any
access-list OUTSIDECO_VPN extended permit ip host x.x.x.x object-group OUTSIDECO_SERVERS
access-list company-split-tunnel standard permit 10.1.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.2.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.3.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.4.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.200.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.5.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.6.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.7.0.0 255.255.0.0
access-list company-split-tunnel standard permit 172.22.22.0 255.255.255.0
access-list company-split-tunnel remark Video
access-list company-split-tunnel standard permit 192.168.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.1.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.2.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.3.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.200.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.4.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.5.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.6.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.7.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 172.22.22.0 255.255.255.0
access-list SSL_SPLIT remark Video
access-list SSL_SPLIT standard permit 192.168.0.0 255.255.0.0
access-list NONAT_SSL extended permit ip object-group local_net_group 172.20.20.0 255.255.255.0
access-list NONAT_SSL extended permit ip 10.200.0.0 255.255.0.0 192.168.9.0 255.255.255.0
access-list tom extended permit tcp host x.x.x.x any eq smtp
access-list tom extended permit tcp host 10.200.200.222 any eq smtp
access-list tom extended permit tcp any host x.x.x.x
access-list aaron extended permit tcp any any eq 2967
access-list capauth extended permit ip host 10.200.200.1 host 10.200.200.220
access-list capauth extended permit ip host 10.200.200.220 host 10.200.200.1
access-list DMZ extended permit icmp any any
access-list dmz_access_in extended permit tcp any eq 51024 any eq 3336
access-list dmz_access_in extended permit icmp any any
access-list dmz_access_in extended permit tcp any any eq ftp
access-list dmz_access_in extended permit tcp any any eq https
access-list dmz_access_in remark rad5110 port 162 out
access-list dmz_access_in extended permit udp any any eq snmptrap
access-list dmz_access_in remark port 23 out
access-list dmz_access_in extended permit tcp any any eq telnet
access-list dmz_access_in remark port 53 dns out
access-list dmz_access_in extended permit object-group TCPUDP any any eq domain
access-list dmz_access_in extended permit object-group TCPUDP any any eq www
access-list dmz_access_in extended permit tcp any any eq h323
access-list dmz_access_in extended permit tcp any any object-group XML
access-list dmz_access_in extended permit udp any any object-group RAS
access-list dmz_access_in extended permit tcp any any range 1718 h323
access-list dmz_access_in extended permit tcp any any object-group H.245
access-list dmz_access_in extended permit object-group TCPUDP any any eq sip
access-list dmz_access_in extended permit udp any any object-group rtp_rtcp_udp
access-list dmz_access_in extended permit object-group TCPUDP any any object-group XML2
access-list dmz_access_in extended permit ip object-group local_net_group any
access-list dmz_access_in remark port 5061
access-list dmz_access_in extended permit tcp any any object-group tcp_tls
access-list outside_cryptomap extended permit ip 10.200.0.0 255.255.0.0 192.168.9.0 255.255.255.0
pager lines 24
logging enable
logging buffered warnings
logging trap informational
logging history informational
logging asdm warnings
logging host outside x.x.x.x
mtu outside 1500
mtu inside 1500
mtu dmz 1500
mtu Wireless 1500
mtu management 1500
ip local pool SSL_VPN_POOL 172.20.20.1-172.20.20.75 mask 255.255.255.0
ip verify reverse-path interface outside
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-631.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list NONAT_SSL
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) x.x.x.12 10.200.200.15 netmask 255.255.255.255
static (inside,outside) x.x.x.15 10.5.0.11 netmask 255.255.255.255
static (inside,outside) x.x.x.13 10.200.200.240 netmask 255.255.255.255
static (inside,outside) x.x.x.16 10.200.200.222 netmask 255.255.255.255
static (inside,outside) x.x.x.14 10.200.200.155 netmask 255.255.255.255
static (inside,dmz) 10.200.200.0 10.200.200.0 netmask 255.255.255.0
static (inside,dmz) 10.4.0.0 10.4.0.0 netmask 255.255.0.0
static (dmz,outside) x.x.x.18 172.22.22.15 netmask 255.255.255.255
static (dmz,outside) x.x.x.19 172.22.22.16 netmask 255.255.255.255
static (inside,dmz) 10.3.0.0 10.3.0.0 netmask 255.255.0.0
static (inside,dmz) 10.2.0.0 10.2.0.0 netmask 255.255.0.0
static (inside,dmz) 10.1.0.0 10.1.0.0 netmask 255.255.0.0
static (inside,dmz) 10.6.0.0 10.6.0.0 netmask 255.255.0.0
static (inside,dmz) 10.7.0.0 10.7.0.0 netmask 255.255.0.0
static (inside,dmz) 10.5.0.0 10.5.0.0 netmask 255.255.0.0
access-group outside_policy in interface outside
access-group inside_policy in interface inside
access-group dmz_access_in in interface dmz
route outside 0.0.0.0 0.0.0.0 x.x.x.12 1
route inside 10.1.0.0 255.255.0.0 10.200.200.254 1
route inside 10.2.0.0 255.255.0.0 10.200.200.254 1
route inside 10.3.0.0 255.255.0.0 10.200.200.254 1
route inside 10.4.0.0 255.255.0.0 10.200.200.254 1
route inside 10.5.0.0 255.255.0.0 10.200.200.254 1
route inside 10.6.0.0 255.255.0.0 10.200.200.254 1
route inside 10.7.0.0 255.255.0.0 10.200.200.150 1
route inside x.x.x.0 255.255.255.0 10.200.200.2 1
route inside x.x.x.0 255.255.255.0 10.200.200.2 1
route inside 192.168.1.0 255.255.255.0 10.200.200.254 1
route inside 192.168.2.0 255.255.255.0 10.200.200.254 1
route inside 192.168.3.0 255.255.255.0 10.200.200.254 1
route inside 192.168.4.0 255.255.255.0 10.200.200.254 1
route inside 192.168.5.0 255.255.255.0 10.200.200.254 1
route inside 192.168.6.0 255.255.255.0 10.200.200.254 1
route inside 192.168.7.0 255.255.255.0 10.200.200.254 1
route inside 192.168.200.0 255.255.255.0 10.200.200.254 1
route inside 192.168.201.0 255.255.255.0 10.200.200.254 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 2:00:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server COMPANY-NT-AUTH protocol nt
aaa-server COMPANY-NT-AUTH (inside) host 10.200.200.220
nt-auth-domain-controller DC
aaa authentication ssh console LOCAL
aaa authorization command LOCAL
http server enable
http 10.200.200.0 255.255.255.0 inside
http 10.200.0.0 255.255.0.0 inside
http 10.3.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set AES256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set asa2transform esp-3des esp-sha-hmac
crypto ipsec transform-set 3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map outside_dyn_map 20 set transform-set 3DES-SHA
crypto dynamic-map outside_dyn_map 20 set security-association lifetime seconds 28800
crypto dynamic-map outside_dyn_map 20 set security-association lifetime kilobytes 4608000
crypto map OUTSIDE_MAP 5 match address outside_cryptomap
crypto map OUTSIDE_MAP 5 set pfs
crypto map OUTSIDE_MAP 5 set peer x.x.x.53
crypto map OUTSIDE_MAP 5 set transform-set 3DES-SHA
crypto map OUTSIDE_MAP 5 set security-association lifetime seconds 28800
crypto map OUTSIDE_MAP 10 match address OUTSIDECO_VPN
crypto map OUTSIDE_MAP 10 set peer x.x.x.25
crypto map OUTSIDE_MAP 10 set transform-set AES256-SHA
crypto map OUTSIDE_MAP 10 set security-association lifetime seconds 28800
crypto map OUTSIDE_MAP 10 set security-association lifetime kilobytes 4608000
crypto map OUTSIDE_MAP 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map OUTSIDE_MAP interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 28800
crypto isakmp policy 10
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 0.0.0.0 0.0.0.0 inside
ssh timeout 20
console timeout 0
dhcpd dns 10.200.200.220 10.200.200.225
dhcpd wins 10.200.200.220 10.200.200.225
dhcpd lease 18000
dhcpd domain company.com
dhcpd dns 10.200.200.220 10.200.200.225 interface Wireless
dhcpd wins 10.200.200.220 10.200.200.225 interface Wireless
dhcpd lease 18000 interface Wireless
dhcpd domain company.com interface Wireless
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 192.5.41.40 source outside prefer
ssl trust-point vpn.company.com outside
webvpn
enable outside
anyconnect-essentials
svc image disk0:/anyconnect-win-2.5.0217-k9.pkg 1
svc image disk0:/anyconnect-macosx-i386-2.5.2017-k9.pkg 2
svc enable
tunnel-group-list enable
group-policy SSL_Client_Policy internal
group-policy SSL_Client_Policy attributes
wins-server value 10.200.200.220
dns-server value 10.200.200.220
vpn-tunnel-protocol IPSec svc webvpn
split-tunnel-policy tunnelspecified
split-tunnel-network-list value SSL_SPLIT
default-domain value company.com
webvpn
sso-server none
auto-signon allow uri * auth-type all
group-policy no-split-test internal
group-policy no-split-test attributes
banner value Welcome to company and Associates
banner value Welcome to company and Associates
dns-server value 10.200.200.220
vpn-tunnel-protocol IPSec
ipsec-udp enable
split-tunnel-policy tunnelall
default-domain value company.com
group-policy DfltGrpPolicy attributes
dns-server value 10.200.200.220
default-domain value company.com
group-policy company internal
group-policy company attributes
banner value Welcome to company and Associates
banner value Welcome to company and Associates
dns-server value 10.200.200.220
vpn-tunnel-protocol IPSec
ipsec-udp enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value SSL_SPLIT
default-domain value company.com
username ciscoadmin password xxxxxxxxxxx encrypted privilege 15
tunnel-group DefaultWEBVPNGroup general-attributes
address-pool SSL_VPN_POOL
authentication-server-group COMPANY-NT-AUTH
default-group-policy SSL_Client_Policy
tunnel-group DefaultWEBVPNGroup webvpn-attributes
group-alias company_SSL_VPN enable
tunnel-group company_group type remote-access
tunnel-group company_group general-attributes
address-pool SSL_VPN_POOL
authentication-server-group COMPANY-NT-AUTH LOCAL
default-group-policy company
tunnel-group company_group ipsec-attributes
pre-shared-key *****
tunnel-group x.x.x.53 type ipsec-l2l
tunnel-group x.x.x.53 ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect tftp
inspect esmtp
inspect ftp
inspect icmp
inspect ip-options
inspect netbios
inspect rsh
inspect skinny
inspect sqlnet
inspect sunrpc
inspect xdmcp
inspect mgcp
inspect h323 h225
inspect h323 ras
inspect sip
service-policy global_policy global
privilege cmd level 5 mode exec command ping
privilege cmd level 6 mode exec command write
privilege show level 5 mode exec command running-config
privilege show level 5 mode exec command version
privilege show level 5 mode exec command conn
privilege show level 5 mode exec command memory
privilege show level 5 mode exec command cpu
privilege show level 5 mode exec command xlate
privilege show level 5 mode exec command traffic
privilege show level 5 mode exec command interface
privilege show level 5 mode exec command clock
privilege show level 5 mode exec command ip
privilege show level 5 mode exec command failover
privilege show level 5 mode exec command arp
privilege show level 5 mode exec command route
privilege show level 5 mode exec command blocks
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:a0689b4c837c79a51e7a0cfed591dec9
: end
COMPANY-asa#

Hi Sian,
Yes on their end the PFS is enabled for DH Group 2.
Here is the information that you requested:
company-asa# sh crypto isakmp sa
   Active SA: 3
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 3
1   IKE Peer: x.x.x.87
    Type    : user            Role    : responder
    Rekey   : no              State   : AM_ACTIVE
2   IKE Peer: x.x.x.53
    Type    : L2L             Role    : initiator
    Rekey   : no              State   : MM_ACTIVE
3   IKE Peer: x.x.x.25
    Type    : user            Role    : initiator
    Rekey   : no              State   : MM_WAIT_MSG4
company-asa# sh crypto ipsec sa
interface: outside
    Crypto map tag: OUTSIDE_MAP, seq num: 5, local addr: x.x.x.13
      access-list outside_cryptomap extended permit ip 10.200.0.0 255.255.0.0 192.168.9.0 255.255.255.0
      local ident (addr/mask/prot/port): (10.200.0.0/255.255.0.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.9.0/255.255.255.0/0/0)
      current_peer: x.x.x.53
      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
      #pkts decaps: 10744, #pkts decrypt: 10744, #pkts verify: 10744
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: x.x.x.13, remote crypto endpt.: x.x.x.53
      path mtu 1500, ipsec overhead 58, media mtu 1500
      current outbound spi: 500EC8BF
      current inbound spi : 8DAE3436
    inbound esp sas:
      spi: 0x8DAE3436 (2377004086)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, PFS Group 2, }
         slot: 0, conn_id: 32768, crypto-map: OUTSIDE_MAP
         sa timing: remaining key lifetime (kB/sec): (3914946/24388)
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0xFFFFFFFF 0xFFFFFFFF
    outbound esp sas:
      spi: 0x500EC8BF (1343146175)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, PFS Group 2, }
         slot: 0, conn_id: 32768, crypto-map: OUTSIDE_MAP
         sa timing: remaining key lifetime (kB/sec): (3915000/24388)
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
    Crypto map tag: outside_dyn_map, seq num: 20, local addr: x.x.x.13
      local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
      remote ident (addr/mask/prot/port): (172.20.20.8/255.255.255.255/0/0)
      current_peer: x.x.x.87, username: ewebb
      dynamic allocated peer ip: 172.20.20.8
      #pkts encaps: 16434, #pkts encrypt: 16464, #pkts digest: 16464
      #pkts decaps: 19889, #pkts decrypt: 19889, #pkts verify: 19889
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 16434, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 30, #pre-frag failures: 0, #fragments created: 60
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 60
      #send errors: 0, #recv errors: 0
      local crypto endpt.: x.x.x.13/4500, remote crypto endpt.: x.x.x.87/2252
      path mtu 1500, ipsec overhead 66, media mtu 1500
      current outbound spi: 2D712C9F
      current inbound spi : 0EDB79C8
    inbound esp sas:
      spi: 0x0EDB79C8 (249264584)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 65536, crypto-map: outside_dyn_map
         sa timing: remaining key lifetime (sec): 18262
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0xFFFFFFFF 0xFFFFFFFF
    outbound esp sas:
      spi: 0x2D712C9F (762391711)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 65536, crypto-map: outside_dyn_map
         sa timing: remaining key lifetime (sec): 18261
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001

WAN Port disconnecting Ethernet between Gigaset 4300 DSL modem

I have a WRT400N setup as a wireless/wired router on a Windstream DSL modem. The Ethernet light on the Modem keeps going out and it log's a disconnect. At the same time, the internet connection light on the WRT400N goes out. I disconnect the router from the network and connected the Windstream Gigaset 4300 Modem/Gateway directly to my PC. No more problems. Any idea on what setting would be making the WAN port ethernet connection act like a RTS/CTS lead in the old RS232 interface?
Steve

The issue is between the DSL modem's ethernet port and the WRT400N's WAN port. The light's on both the router's Internet connection and the modem's Ethernet port goes out, like the cable is being unpluged. I have replaced the cable, so it's not that. Naturally, all devices, both wired and wireless cease internet connectivity when this connection is open. I have connected the DSL modem/gateway directly (via the same ethernet port) to two different computers and never lose this connection, which makes me think that the WRT400N is opening (disconnecting) the internet port at different intervals for some reason. It happens both wireless connections and wired connections are using the internet. As I type this, my PS3 (wireless G) is downloading a 1.4 gig demo and about every 30 sec. the ethernet light on the modem goes out, at the same time the internet light on the router goes out also. It varies in time, some time as little as 10 sec. between disconnects, sometime it will stay connected for over 2 min. It's a closed network with 3 wired connections (2 computers and Dish VIP922 DVR), several wireless connections (1 Computer via N adapter, Wii wireless G, PS3 Wireless G, Ipod touch Wireless G, 2 cell phones wireless G). No QoS or port forwarding is in use.

Voip between cisco and avaya

We have to implement Voice over IP on our IPLC circuit between foreign office and India office.
Topology is such that our foreign office is having 1700 series router with wan card
(Wic-1T) and one two port FXO card connected to PBX for PSTN and local connectivity.
India end we have a cisco 1700 router with wan card (Wic-1T) and on lan we have Avaya S8300 media server with multiple phones connected to it. Avaya server is acting as a voice gateway at India end. Avaya server is connected to LAN on Ethernet.
We have configured IPSEC site-to-site VPN between both the locations.
Requirement:-
Over the VPN tunnel we want to enable voice communication between both the locations.
i.e between cisco at foreign end and avaya server at India end.
1) India office users via IPLC should communicate over voice and data with the foreign office (Avaya extensions to FXO in Foreign office).
2) Foreign office should communicate with the india office users connected to IPLC link (FXO to Avaya server extensions)
Any suggestions/config will be appreciated
Attaching the india end router config.
Thanks

Hi
Before getting onto the requirements,from now on i would suggest you to mask the ip (public) address part included in the configs while posting in any general forum.
These are the links which you can use up here for the ref..
You need to check out for the possible codes and other compatible points which you need to configure on both the sidees..
http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a008009431b.shtml
http://www.cisco.com/en/US/products/hw/routers/ps259/products_configuration_guide_chapter09186a008007e606.html
http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a0080080afd.html
i m not sure though about the configuration of Avaya box but you can mention the remote end routers ethernet ip as the destination ip or the target for the call termination.
And in the remote router while configuring the dial-peer pots and dial-peer voip binded on the FXO itnerface make sure that you are mentioning the Avaya box ip as the session target.
regds

Routing issue between Cisco Nexus and Cisco 4510 R+E Chassis

We have configured Cisco Nexus 7K9 as core and Cisco 4510 R+E as access switches for Server connectivity.
We are experiencing problem in terms of ARP learning and Ping issues between Cisco Nexus and end hosts.

Hi,
So you have N7k acting as L3 with servers connected to 4510?.
Do you see the MAC associated with failing ARP in 4510?. Is it happening with all or few servers?. Just to verify if it is connectivity issue between N7k and 4510, you can configure an SVI on 4510 and assign address from same raneg (server/core range) and perform a ping.
This will help narrow down if issue is between server to 4510 or 4510 to N7k.
Thanks,
Nagendra

Cisco or Linksys DSL router that will work with Windows XP Pro?

Any suggestions for a CISCO or LINKSYS DSL router to replace a Zyxel (Century Link) PK5001Z? System is Windows XP Pro, 20 wireless and wired devices connected (including 6 CISCO WVC210 IP cameras ). The Zyxel forwards as many ports as I want, but will only open a limited number of the ports. This limits my access thru the internet (local network sees all cameras). Zyxel support is unable to help.

Hi Edward, if you're looking for a modem/router combo device, Cisco offers the SRP500 series. However this product is EOS/EOL. The small business product line does not have any other DSL termination router aside the SRP series. If your goal is to use a DSL modem and then have a router, you may want to consider RV325 router as it is very feature rich and quite robust.
-Tom
Please mark answered for helpful posts

Basic setup for Cisco RV325 router

I am having problem with the basic setup of RV325 router.
Example:
STEP 1 Connect a PC to a numbered LAN port on the device. If the PC is configured to
become a DHCP client, an IP address in the 192.168.1.x range is assigned to the
PC.
Which LAN port does it meant?
I tried the router connection on different LAN ports to a PC but the browser would not launch anything at 192.168.1.1.
Can anyone help?
Thank you.

Hello,
It sounds like you are trying to access the web interface of your router so you can configure it. First of all, I'll go over the ports of the router with you.
The last port of each row (on the right side) of the device is for the WAN (Wide Area Network) that's designated for where you connect to your ISP (Internet Service Provider). Most likely, you will connect your modem to one of those ports. Any ports to the left of those are your LAN ports (Local) where you can connect your PC.
Once you connect to one of those ports, your PC should get an IP address. If you are unable to get to the web interface of the router, you will want to confirm your IP address and default gateway (which is the IP address of the router).
This can be done in Windows by:
Select Start > Run. Type command or CMD into the dialog box, then click OK.
In the resulting command line window, type ipconfig.
C:\>ipconfig
You will see something similar to this resulting output:
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : 3Com EtherLink 10/100 PCI For Complete PC Management NIC (3C905C-TX)
Physical Address. . . . . . . . . : 00-01-03-AB-0E-6P
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 192.168.1.10
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
This will give you 3 key pieces of information you will want to verify. First, you want to see that your network adapter is set to DHCP. It should say yes next to it. Second, your IP address needs start with 192.168.1.x
In this example, it is 192.168.1.10, which is fine.
Lastly, your default gateway should be preset to 192.168.1.1. If it is not, write that number down and try to access that IP address in your browser.
Note: If your browser is just coming up blank, you may want to try a different browser.
Hopefully you'll be able to get into your router at this point. If not, please provide the output of your IP config statement so we can further troubleshoot your issue.

Specify SQL Server Port During Setup

I am installing ConfigMgr 2012 R2 in an environment that requires remote SQL. In addition, the remote SQL uses a custom port and does not run the SQL Browser service.
Is there a way to specify the SQL Server port during setup? I know I can specify the port for the SQL Service Broker, but I need to specify the port for the SQL Server instance itself.
Any insight/experiences are greatly appreciated!
Thanks,
Jeff

You will need to change the port in SQL Server Network Configuration
See this technet documentation : https://technet.microsoft.com/library/ms177440.aspx
Benoit Lecours | Blog: System Center Dudes

Can I run a cat5 cable to a 4 port hub from a cisco router then connect one of the hub's output ports to an airport express to 'extend' my wireless range?

Can I run a cat5 cable to a 4 port hub from a cisco router then connect one of the hub's output ports to an airport express to 'extend' my wireless range?
Flow would be
Cable modem---->cisco e2000 wifi router (This is broadcasting wifi but not strong enough)---->4 port hub ---->airport express (to extend the wifi in another part of house)
thanks!

Yes, you can do this as you stated. In essence you will want to configure both routers for roaming network. Please check out the following Apple Support article that describes this type of network. Although this article uses two or more AirPorts, it can be done with just about any manufacturer's router.

WRT610N V1 will not allow port forwarding via HP Mediasmart Server

I have the WRT620N router and an HP MediaSmart server connected to it. My source is a cable modem. WHen I try to set up the server for remote access, the router is not found. I am continually getting "Port Forwarding failed" errors from the server. I also have several iPhone apps used to control devices on the network (DVR, BluRay player,etc) that will not connect. (These worked before I changed to this router.)
I have verified that the UPnP is enabled.
I have been struggling with this issue for several months and have not had any luck getting help from the forums, but will tryi again.
Any help would be appreciated.
Thanks,
Joel WZ
Thanks,
Joel WZ

Did you tried to enable Remote Management Access on the router setup page?
If no, then Enable Remote Management Access under Administration tab and then check.

Difference between cisco prime infrastructure and cisco WCS

Can you explain me difference between cisco prime infrastructure and cisco WCS.. I'm little bit confuse...
Thanks..

Hi Hasan,
In terms of features...You can say PI is more advanced version of WCS and NCS. All the stuff possible in WCS/NCS can be done on PI as well.
But from the architecture perspective , there are differences. If I remember correctly , WCS is based on 32 bit OS while NCS and PI based on 64 bit OS. For the same reason you cannot do inline upgrade from WCS to PI via any path and will have to change the platform/Hardware itself before moving to PI. However , inline upgrade from NCS to PI is possible if we follow the correct path.
Regards
Dhiresh
**Please rate helpful posts**

Will a 2 port LAG setup between 2 cisco 200-50s create routing issues?

Similar Messages

Maybe you are looking for