Windows 8 with HP Photosmart 7700 network

I want to  have my HP Photosmart 7760 work with windows 8 within a network. Not with USB Cable.
I do have my HP Photosmart 7760 working with my windows xp with in a network.
Is there a way going about changing the autorun file to include windows 8 for the HP Photosmart 7760
My E-mail Address is {Personal Information Removed} Please

I would recommend unistalling the device and reinstalling it using the link below :
https://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=305375
-Spencer 

Similar Messages

  • Windows 10 with HP Photosmart 5520

    I have a HP Photosmart 5520 working on Windows 7 64bit.  Will it be able to convert to working on Windows 10 if I upgrade or will I have to buy a new printer?  Thanks for your help please

    Hi SB1961. You can reference the below link for supported printers. http://support.hp.com/us-en/document/c04658195 It looks like your printer is supported under Windows 10, and the driver is currently available. To find the driver do a search on the below link for your printers model number.  Then select the appropriate operating system. http://support.hp.com/us-en/drivers Regards,PrntDr

  • After updating my Iphone 4s to os 7.1.1 ota, my phone went into recovery mode. Yet when I try to restore it with Itunes on my windows 7 laptop it says the network connection has been reset! My phone has the itunes logo and charger symbol on it .

    After updating my Iphone 4s to os 7.1.1 from 7.1 over the air, my phone went into recovery mode. Yet when I try to restore it with Itunes on my windows 7 laptop it says the network connection has been reset. Make sure your network settings are correct and your network is active, or try again later. My phone has the itunes logo and charger symbol on it, as well as an arrow pointing at the Itunes logo. After holding the sleep button down or even doing the hard reset the same screen comes up on my phone regardless of whether it is plugged in or not to my computer. I have turned my computer off and on again. It is plugged in and charging as it's battery life is very short. I also reset my modem and the same error message pops up. The only option on my computer when my phone is plugged in is to restore it. My firewall also allows Itunes through it. I have literally tried everything I know being someone who knows very little about technology. I also do not want to hear about how the update worked for other people. My phone has been in recovery mode for 5 hours at least now so it will just make me more frustrated if a bunch of people post about how the update worked for them.

    Once the Device is asking to be Restored with iTunes... it is too late to save anything... and you must continue with the Recovery...
    kevinpowell1 wrote:
    how can i get it out of recovery mode?
    Make sure you have the Current Version of iTunes Installed on your computer
    iTunes free download from www.itunes.com/download
    Then See Here  >  http://support.apple.com/kb/HT1808
    You may need to try this More than Once...  Be sure to Follow ALL the Steps...
    Take your time... Pay particular attention to Steps 3 and 4.
    Some users have reported as many as 8 or 9 attempts were necessary before success.
    After you have Recovered your Device...
    Re-Sync your Content or Restore from the most recent Backup...
    Restore from Backup  >  http://support.apple.com/kb/ht1766
    If the issue persists...
    Then a Visit to an Apple Store or AASP (Authorized Apple Service Provider) is the Next Step...
    Be sure to make an appointment first...

  • Multiple page scanning with HP photosmart 5514 and windows 8.1

    I am unable to san multiple pages to one document since changing to Windows 8.1.
    Can you help please?
    Thanks in advance.
    This question was solved.
    View Solution.

    Hi @KC1719 ,
    I see that you are experiencing issues scanning multiple pages to one file, since updating to Windows 8.1.
    I would be happy to help you.
    Did you uninstall the old software and reinstall the latest drivers?
    Here is the link for newest drivers. HP Photosmart Full Feature Software and Drivers.
    Here is a document for scanning, that you may want to take a look at.
    Scan from Windows 8 With the Full Feature HP Software for HP Multifunction Printers.
    This is a screen shot for changing the settings in the HP Scan Software.
    If you need further assistance, just let me know.
    Have a great day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • HP Solution missing for Windows 7 Profession​al 64 bit with HP Photosmart C5100

    Message indicates HP Solution missing for Windows 7 Professional 64 bit with HP Photosmart C5100.
    What is the solution?

    Hello love2travel1960 , and welcome to the HP Forums, I hope you enjoy your experience!
    I see you are having issues finding the installer.  I would like to help.
    I would recommend downloading and installing the HP Officejet Pro Full Feature Software and Drivers.
    Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
    Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
    Jamieson
    I work on behalf of HP
    "Remember, I'm pulling for you, we're all in this together!" - Red Green.

  • HT3819 Is it possible to share a printer (attached to a Windows-7 PC) on my home network, with an iPad, iPhone or a Mac?

    Is it possible to share a printer (attached to a Windows-7 PC) on my home network, with an iPad, iPhone or a Mac?

    Possibly. You'd need to see if your printer has any programs you can put on that attached computer to allow it to be a print server.
    I'd start with your printer manufacturer first. See if they offer anything. for your model. If not, then you can look for any printer apps or programs.

  • I cannot select the Paper Size when I try to print with HP Photosmart B110a with Windows 8.1 64bit

    I cannot select the Paper Size when I try to print with HP Photosmart B110a
    The same printer was working OK with my old PC with OS Windows 7
    However I got a new PC with OS Windows 8.1 64bit
    I installed the new driver for HP Photosmart B110a that I dowloaded from HP site. Driver forWindows 8.1 64bit.
    In addition to not being able to chose the paper size, also when I go to Printer Properties in Options, all the characters are non-ascii.
    Do you know what may be the problem?
    Thank you

    Hello Nanu64,
    Welcome to the HP Forums.
    I see that you are having some issues when attempting to print from your computer.
    I also see that you stated that not all the options are available in the printing preferences options.  This could be because the installation was not complete or it failed.
    I suggest that we do a complete uninstall/ reinstall as well as some additional steps.
    First off, please make sure that you have the printer power cable connected directly to a wall outlet and not a power bar/strip. Here is a document that uses a LaserJet printer as an example but it is meant for HP products in general. Please click on the following link that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
    If you have the printer connected to the computer with a usb cable, please remove the cable from both ends and leave it disconnected until further notice.
    The next link that I have for you will give you detailed instructions for Uninstalling the Printer Software.  Once the uninstall is complete, reboot the computer so that the changes take affect.
    When the computer is back up and running, please disable any firewalls or anti virus protection you may have running. We don't want anything getting in the way of the reinstall.
    The following download is the HP Photosmart Full Feature Software and Drivers.  Save this download to the desktop of the computer so that it creates its own icon.  This will make it easy for us to find when the download is complete.
    Double click the new icon and follow the installation instructions.  The installation will give you connection options (Wireless , usb or Ethernet), if connecting usb, please wait for the prompt to connect the cable.  Connecting the usb cable before hand can cause an issue with the installation.
    If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
    Thanks for your time.
    Cheers,  
    Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    W a t e r b o y 71
    I work on behalf of HP

  • How do install the network adaptor for windows 7 with boot camp?

    How do I install the network adaptor for windows 7 with boot camp?

    boot camp forum: https://discussions.apple.com/community/windows_software/boot_camp 

  • Help with Boot Camp Assistant network problem while downloading windows support system!

    I need to download Windows support software, but just keep encountering a problem which says "Can't download Windows Support Software because of a network problem." What should I do? I'm currently using Boot Camp Assistant v5.0.0, and OS X 10.8.2. Help! What can I do to solve this network problem? Please and thank you (:

    I have the same problem.  Anyone out there?  Hello?

  • Laptop sees Photosmart on network, but won't connect

    I have a Pavilion dv4 with Windows 7.  I have a Photosmart C4795.  My printer used to be hooked up to my desktop, but my HP Desktop has crashed and it's trash.  So now I'm trying to hook my laptop up to my printer on the network.  For two days, I was able to connect and download with no problems, but my laptop would never print.  Wouldn't even do a test page.  Uninstalled and reinstalled at least 10 times.  I ran the scan doctor and it said there was nothing wrong with my printer, but it wouldn't print a test page either.  It then had me do an internal test page and that one work, so it diagnosed that the software was bad.
    All of that was yesterday.  NOW TODAY, I uninstalled and reinstalled the software.  It's the most up to date software and drivers from the HP Support page.  Now, my printer recognizes that the printer is on the network, but won't install the printer.  It did the diagnostics, then brought up the screen where it showed my computer on the left, modem in the middle, printer on the right.  It gets about halfway through setting it up, then quits and says it can't complete.  I ran the scan doctor again and it says that the full software version is not installed.  I JUST downloaded it from the website and installed it twice and it won't work.  The version I download from the website is around 146mb, but when I download it from the scan doctor page, it's over 200 mb.  I run that software and it is exactly the same.
    I have tried to set it up via usb.  It gets to the 7th of the 8 steps, then it won't go any further.  Again, the printer is detected, but it says the appropriate drivers aren't there.
    I have tried to set up it's own port using it's USB and a different driver, but that gives me an error.  Unable to install printer. Operation could not be completed (error 0x000003eb).)
    Would someone please help me, and then if I reply with what it is doing next, please respond?  
    Please help me get through this.  Two days now and I don't have a solution.
    Just me, friebe13

    Hi,
    If you are using AT&T wireless router to connect the Photosmart to network, you can refer this link for a solution :
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03112838&tmp_task=solveCategory&cc=us&dlc=en&la...
    Hope this helps.
    Click "Thumbs up" if this helped you in any way.
    Its a pleasure talking to you ! Have a Great Day!
    I work for HP, but my comments and recommendations here are my PERSONAL views and NOT on behalf of HP.

  • How to print from windows 7 pc on time capsule network?

    I added a new pc with windows 7 on my time capsule network.  Existing network includes 2 macbook pros and 1 mac mini with boot camp and windows xp.  I have been using the windows xp with bootcamp on the mac mini and printing from it for a couple years.  We don't share files between the notebooks and mac mini, just internet access and printing.  My bootcamp side got too full which is why I added the new windows pc (yuk) for my windows programs but I cannot figure out how to get the windows pc to recognize my printer connected to airport time capsule.  I installed the printer software and drivers and connected it with usb and printed but when I connect the printer back to time capsule the pc doesn't see it.  Also, I downloaded bonjour from apple site but still no go.  Any help is appreciated.  As you can probably tell, I only know enough to be dangerous.  That's why I love my Macs, they just work!

    The problem is you loaded the printer directly and now do not have it plugged in.. so delete the printer in the control panel.. then setup the printer again.. this time connect to it as network printer. The bonjour should make it available as a network resource..
    Tell me if you still run into trouble doing that. You may need to load the IP of the TC manually..
    Window7 has higher security level than xp.. and that can sometimes also cause issues.
    Are you using SMB compliant names for the TC, wireless and printer??
    Can the windows 7 computer get internet via the TC? Can you ping it?
    Look up how to reduce the security level in windows to match xp.. I don't remember the details but you have to do some nifty footwork.

  • Epson Stylus Pro 9800 errors on 32-bit Windows 7 with Adobe CS4

    Epson Stylus Pro 9800 errors on 32-bit Windows 7 with Adobe CS4
    Question: We are experiencing some major errors with printing to our Epson Stylus 9800 Pro. Some of our large files are spooling about 16K, then crashing Photoshop. Sometimes we are getting partial prints (the left most 3-4 inches of print, or the file starting to print about 1/2 way into the file itself), sometimes it just spools for a few minutes, then stops, with nothing coming from the printer at all.
    At Epson's request, we have tried the following:
    reinstalling Windows 7 print driver
    Reinstalling Adobe CS 4
    Installed NEW NIC in printer
    Installed new network line to printer
    Installed new main board on printer
    Printed from a PC directly connected to printer via USB and crossover cable
    This issue is very bizarre in that it is random and sporatic. Same file will cause one of the above errors, then, another attempt to print same file will be successful. We have several Windows 7 machines that get the issue, while several Windows XP machines are fine. Epson instructed us to install the newest (win7) driver on the XP machines, issue then affects XP machines. Uninstalling new driver and re-installing old driver on XP machines resolves issue on XP machines.
    Is this an issue with the Epson driver? CS4 on Windows 7? Or some other malady?
    When Photoshop crashes, the following error log is created: Log Name:      Application
    Source:        Application Error
    Date:          10/6/2010 1:31:16 PM
    Event ID:      1000
    Task Category: (100)
    Level:         Error
    Keywords:      Classic
    User:          N/A
    Computer:      _PCNAME_._OUR_DOMAIN_.com
    Description:
    Faulting application name: Photoshop.exe, version: 11.0.2.0, time stamp: 0x4bf2d4f6
    Faulting module name: E_FJBLDBE.DLL, version: 0.1.1.7, time stamp: 0x469dea6c
    Exception code: 0xc0000005
    Fault offset: 0x0001c9ba
    Faulting process id: 0x1cf8
    Faulting application start time: 0x01cb657c010cac1c
    Faulting application path: C:\Program Files\Adobe\Adobe Photoshop CS4\Photoshop.exe
    Faulting module path: C:\Windows\system32\spool\DRIVERS\W32X86\3\E_FJBLDBE.DLL
    Report Id: 85870535-d16f-11df-b849-406186f3bc8f
    Event Xml:
    <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
      <System>
        <Provider Name="Application Error" />
        <EventID Qualifiers="0">1000</EventID>
        <Level>2</Level>
        <Task>100</Task>
        <Keywords>0x80000000000000</Keywords>
        <TimeCreated SystemTime="2010-10-06T17:31:16.000000000Z" />
        <EventRecordID>5497</EventRecordID>
        <Channel>Application</Channel>
        <Computer>_PCNAME_._OUR_DOMAIN_.com</Computer>
        <Security />
      </System>
      <EventData>
        <Data>Photoshop.exe</Data>
        <Data>11.0.2.0</Data>
        <Data>4bf2d4f6</Data>
        <Data>E_FJBLDBE.DLL</Data>
        <Data>0.1.1.7</Data>
        <Data>469dea6c</Data>
        <Data>c0000005</Data>
        <Data>0001c9ba</Data>
        <Data>1cf8</Data>
        <Data>01cb657c010cac1c</Data>
        <Data>C:\Program Files\Adobe\Adobe Photoshop CS4\Photoshop.exe</Data>
        <Data>C:\Windows\system32\spool\DRIVERS\W32X86\3\E_FJBLDBE.DLL</Data>
        <Data>85870535-d16f-11df-b849-406186f3bc8f</Data>
      </EventData>
    </Event>

    Giving that a go.
    Thanks!

  • I connected my ipod touch 4g wi-fi with laptop ad hoc network....it's showing wi-fi signals but internet is not working...what is the problem in that can anyone help me...inadvances thanks

    I connected my ipod touch 4g wi-fi with laptop ad hoc network....it's showing wi-fi signals but internet is not working...what is the problem in that can anyone help me...inadvances thanks

    my laptop is Windows 7 and ip is this
    192.168.102.12
    255.255.255.0
    192.168.102.1
    DNS
    192.168.254.2
    192.168.254.3
    in ipod touch 4g is DHCP and its showing
    ip address 169.254.192.139
    subnet mask 255.255.0.0.
    remaining all blank

  • Update doesn't seem to work with my job's network...

    I work at a large company, and pretty much 99% of the team members here are on Windows - myself and another designer are on Macs. We've successfully had our Macs on the same network as everyone here. We log into our Macs, just like everyone logs into their Dell's on our network. I recently did the Yosemite update and when rebooting it up (while still on my work network) the status bar stopped at 50% and it just stayed there until I had to take it to a Mac store to get fixed. They pretty much backed up my computer, wiped the computer, than re-installed Yosemite and restored old files on my computer, and it worked fine, BUT I was no longer on my work's network. All weekend, my MacBook worked great but without all my software and access to my job's network. So the following Monday, I brought my MacBook to my IT department to get put back on the network and get all of my old software installed again. While rebooting, the same thing happened - status bar stopped at 50% and stayed there.
    So, conclusions I've made - Yosemite is having a problem with my work's network and is not even booting up. It is a Windows based network. Earlier this year, I feel like I successfully updated to Maverick with no problems while on my work's network. Does anyone have any input they can provide?

    Wi-Fi?
    Wi-FI connection drops
    Wi-Fi Problems in OS X Yosemite
    Wi-Fi Problems in OS X Yosemite (2)
    Wireless Diagnostics
    Also try turning off Bluetooth.
    Troubleshooting Wi-Fi issues in OS X
    Wireless Connection Problems - Fix
    Wireless Connection Problems - Fix (2)
    Wireless Connection Problems - Fix (3)
    Wireless Connection Problems - Fix (4)

  • Problem with 2 computers Airport network

    While long time comfortable with Mac, I am novice with Airport/network.
    I have a MacMini (with Airport card) and a new PowerBookPro (15" 2.2 Intel Core 2 Duo and Airport card). I have new Airport Extreme Base device and I have successfully set up wireless internet connection for both computers.
    I have also successfully through Airport set up so my mini connects with MBP/sees the MBP on the Mini desktop, etc..
    My problem is that I haven't done the +correct rain dance+ so that the MBP connects to see my Mac mini on the MBP.
    No clue what is being done wrong, except: In Finder of Mini under Go --> Network the MBP is listed and I then connect through steps of that window.
    However, on the MBP Finder under Go --> Network, I just get a "flash" and no menu window is displayed at all.
    Strange to me that computer network gods are so easily accommodating one way (Mini connects with MBP via Go/Network) and totally absent in reverse (no connect of MBP via Go/Network with Mini).
    I hope someone can guide me through the correct ritual so that the 2 computers can go both ways. TIA.

    I solved my problem!
    Looking in other discussion forums, I found workaround for the fact that when on MBP/Finder/Go/Network all I got was a flash and no window.
    The recommended solution worked! To simply logout and then login on that MBP. This restored the Go windows and Network window showing my MacMini to connect with.
    So now both computer go both ways.

Maybe you are looking for