Windows XP-Pro will not install on my new P965 Platinum

Question

I hope someone can help me with my problem.
It seems that everytime i try to install Windows XP-Pro after the initial
drivers setup i get this Error Message:
A problem has been detected and windows has been shut down to prevent
damage to your computer.
If this is the first time you've seen this stop error screen, restart
your computer. If this screen appears again, Follow these steps:
Check to be sure you have adequate disk space. If a driver is identified
in the stop message, disable the driver or check with the manufacturer
for driver updates. Try changing video adapters.
Check with your hardware vendor for any BIOS updates. Disable BIOS
Memory option such as caching or shadowing. If you need to use Safe Mode
to remove or disable components, restart your computer and press F8 to
select Advance Start up options, and then select Safe Mode.
Technical Information:
*** STOP: 0x0000007E (0xc0000005, 0xF78350BF,0xF7C81208,0xF7C80F08)
*** PCI. sys-address F8350BF base at F782E000, Datestamp 3b7d855c
This is a new build with a Samsung Spinpoint SP2504C SATAII Drive but
when this occurred i thought that it might be the drive that was the
problem.So i therefore put it i my Old PC and tried to install Windows
XP-Pro onto it which i did with no problems at all.
I then put the drive back in my New PC where it Booted Up First Time and
runs OK and i have even installed Software onto it.In fact i am using at
this very minute as i type.
Unfortunately when i still try to Reinstall Windows XP-Pro on my New Build
with my P965 i get the same Error Message as above.
 Can anybody please help.
                                   Thanks
P965 Platinum
Intel Core 2 Duo E6300
Samsung Spinpoint SP2504C SATAII
Corsair 1GB DDR2 Twin2X(5x512MB)
inno3D GeForce 7600GT
Creative Sound Blaster X-Fi Extreme Music Sound Card
NEC ND-3520 DVD
Arctic Cooling Freezer 7 Pro
Thermaltake Toughpower 600W
Thermaltake Tsunami Dream Case

Answer 1

Quote
I hope you don't mind me asking this question for Jack the Newbie.
You say i have to use a Windows XP-Pro Install-CD that includes SP2 as well as the JMicron driver for the JMicron IDE-Port which i have my Optical Drive connected to.I know this is telling me how to fix my problem, but what i would also like to know is WHY do i have to install it with SP2 & the JMicron driver like this on my P965 when it installed on my old pc with just the XP-Pro Install-CD.
Your Windows Installation CD should be as up to date as possible, especially for newer hardware.  SP1 is from 2002, SP2 was released in 2004. Neither SP1 nor SP2 install CDs provide the proper drivers for the JMicron chipset used on your mainboard.  I cannot give a detailed list about the differences between SP1 and SP2. I just know, that there are a lot of problems when people do not use SP2 on Intel 975/965 Chipset-boards which where released in 2006. 
When you say that your installation works fine on your old PC I believe you.  It worked on my old Laptop too.  However I was not able to install XP Pro on my 975X-board without SP2 at all until I upgraded my Installation CD.
Quote
Garfield,
I had exactly the same problem--because I had my optical drive hooked up to a Promise IDE controller, rather than to a mobo IDE connection.  Turns out the Promise will read and write the optical drives OK, just won't boot from them properly.  And, somehow, that affects Windows Setup.
I don't know anything about the JMicron and the need for SP2.  But, as you can see from my sig, I'm using XP Pro SP1, and once I moved my NEC 3500 back to the mobo IDE (as secondary behind my IDE hard disk) everything worked like a champ.
Just my $.02.
Stahlwird
To relate Garfields problem with your solution is a mistake.  Your board does not use any JMicron hardware, has NVidia chipset instead of Intel and an AMD CPU.  Your are talking about a totally different Setup here.