Wireless router console unable to be viewed

I have a G router that I never have issues with until now.   I jested installed windows 7 on all my machines and after doing this I am unable to get to the Linksys Console.   I have tried IE 8 and Firefox but still no luck.   I first thought it was a bad password, but it logs on with no errors.   I just get a blank screen that I can do nothing with.   Does anyone know how to fix this issue

A blank page is usually solved by performing a power reset of the router.  Also, you may have to reboot all PCs as well after the power reset.  Since this is a problem on all PCs, it's likely a router problem unless you haven't installed network adapter drivers on any PC after the Windows 7 upgrade.
If a power reset doesn't work, you may need to perform a factory reset using the reset button on the back of the computer.

Similar Messages

  • Hp photosmart 5520 unable to connect to wireless router

    The printer worked fine-I went on vacation and now it won't work. I ran the wireless network test and it said"hp printer is unable to connect to your wireless router".  The wireless router is connected and running fine.  My wireless hp computer (windows 7) works just fine.
    The report satd "network name ssid found" said FAILED
    But "current configuration" showed the SSID
    can anyone offer a fix?
    Help
    colleenmercy
    This question was solved.
    View Solution.

    Hi colleenmercy,
    On the network menu, select Restore Network Defaults.  This will clear the current network settings and allow  you to reconnect the printer to the network.  You can use the wireless setup wizard or reinstall the HP software to reconnect.
    I was an HP employee.
    Please mark the post that solves your problem as "Accepted Solution"

  • I am unable to stream Netflix to my Iphone or Apple TV, from my wireless router . . . even though I am able to watch Netflix on my WII (also wireless) and desktop computer (not wireless).

    I am unable to stream Netflix to my Iphone or Apple TV, from my wireless router . . . even though I am able to watch Netflix on my WII (also wireless) and desktop computer (not wireless).
    On the Iphone and Apple TV I can connect to Netflix . . . it recognizes me and my account settings . . . and I can veiw all my recent programs and show titles, descriptions, etc..  But when I select one to watch I get a message saying:
    "ERROR A PROBLEM OCCURED WHILE PLAYING THIS ITEM. TRY AGAIN LATER, OR SELECT A DIFFERENT ITEM. GO TO WWW.NETFLIX.COM/SUPPORT FOR MORE INFORMATION. (139)
    Netflix support say there is nothing wrong on their end . . . that it is an Apple issue.  They see the request for the show, the devices are registered . . . but it shows 0 bandwidth to the device.
    My Apple TV did this when I first hooked it up a couple of weeks ago.  Then after a few days started working with Netflix, for no apparent change . . . now doesn't again for the past couple of days (I think that it auto restarted the other night after a virus scan).
    Very frustrating, and driving me nuts!  Has anyone else had and been able to resolve this problem?

    Troubleshooting
    Apple TV2 update one day and netflix is browsing but not launching the actual content (error 139)
    Ipad2 (another ios device) forces me to update netflix if I want to use it and I get the same error 139 on it.
    **** now I have two not ways not working where prior to some update it was fine.
    Nintendo Wii is still working ( mind you running an ancient version of netflix )  Dusted the Wii off and gave it to the kids use.  Now they are happy again...
    PC is also still working ( using some other flash client ) but that's just of interest, we're not going to be watching tv with that.
    My wife's iphone 4s is still working.  Odd.. still ios but for somereason I am not forced to update the version. So basically she could mirror stream up to the apple tv with it.  Nice feature of Ios5.  Later found out it is using 1.4 version of netflix.  The most useful thing out of that is that all 3 of the devices are Ios and it was actually the iphone with the 1.4 version of netflix that still worked!
    I heard from a friend who was on a different ISP he was still working so I took my appletv2 and ipad2 over to my brothers house who is on that same ISP as my friend and both started working.  So the ISP is involved too!
    Brought the appletv2 and ipad2 back to my house hoping it would maybe still work.  No dice   Broken again.
    Searched the appstore for a decent packet analyzer and there isn't really anything.  I was able to sniff the traffic with my PC and also on my juniper ssg5 confirmed that.  Turns out port 80 traffic is actually failing and authorization is not happening.  The other clients do not do this...
    Asked a buddy from work who used to work at the ISP if he could make a call to some one who might actually know what is going on.  He came back pretty quick and said yea they are trying really hard to get the beta patch in from Bluecoat asap. 
    So knowing that it was actually Netflix that changed when it hit 2.0 and in my case the ISP made the adjustment it's pretty safe to say this issue is going to be ongoing unless netflix changes again the way they authorize for licenses.
    So that's the summary of what went right down the troubleshooting path but I'll tell what what didn't
    2 calls to Netflix (useless... waste of time... they are too quick to blame anyone but themselves)
    1 call to apple support (support call was going to cost more than it cost for me to change ISPs)
    2 calls to ISP (through the normal means - regular support number)
    So why is this intermittantly working sometimes?  If you are lucky enough to authorize to an IP address that is not cached they voila you are going to get an authorization / a license to watch the show.  Some people report after defribulating their appletv (reseting, rebooting, dns changes, you name it) they get it working.  Over the past month we all seem to have got it working for some period of time only to lose it a day to two later.
    It's now been several days since the beta patch to the bluecoat and 4 of us who have been communicating on the issue appear to be online all at the same time for those several days and that is a good sign that we might be out of the woods on the issue.
    Hope this turns into something helpful for someone else out there.

  • HP Officejet Pro 8000 Wireless: HP printer unable to connect to wireless router.

    Installing new printer,  getting error msg saying HP printer unable to connect to wireless router.   MAC address filtering may be enabled on your wireless router which can prevent HP printer from connecting to your wireless network during setup.
    SOLUTION says:  If MAC address filtering is enabled and you would like to keep it enabled, you must add the MAC addressof your printer to the list of permitted devices for your wireless router before continuing.
    My router is WD My Net N900 Router. MAC filtering is diabled. My security mode is WPA/WPA2 Personal. 
    I have run out of ideas to try and fix the issues, would appreciate some help.
    Thanks,

    Hi Jamshidk
    I am surprised you are getting that message and you checked the router settings and it is showing that the Mac Filtering is disabled.
    I would suggest connecting the printer to the router with a ethernet cable to get a valid IP address and then setup the wireless.
    Print a configuration report.
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&​dlc=en&docname=c01554589&lc=en&product=3760410&tmp​...
    Type the IP address from the configuration page  in the address bar into internet explorer browser. This will open the embedded web server for the printer. Click on the Networking tab, on the left hand side select wireless. After this is setup and applied, disconnect the ethernet cable.
    Should be on the wireless network. Takes about 1 minute.
    Run the add printer wizard.
    Go to start, devices and printers and select add a printer. (Win 7)
    Test the printer.
    If you need more assistance just let me know.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • I've reset my network settings , my wireless router is working fine, my iPhone keeps saying unable to join network.

    I've reset my network settings , my wireless router is working fine, my iPhone keeps saying unable to join network.

    Are there other devices that can connect to your Wi-Fi and work just fine?
    You can troubleshoot this using http://support.apple.com/kb/TS1398 as well. If you need to restore your iPhone at all, use http://support.apple.com/kb/HT1766?viewlocale=en_US and http://support.apple.com/kb/HT1414?viewlocale=en_US and set it up as new to see if this still happens. If it does, you might need a replacement

  • Network diagnostics is not accepting the WEP password on my wireless router. I know the password is case sensitive and was very careful in entering it but it still gives me the "Unable to join Wi-Fi Network" error message.

    I need help setting up the wireless router for my iMac. I did not know the WEP password when I first turned it on to set things up. Now that I know the WEP password I cant get Network Diagnostics to accept it. I know it is case sensitive and was very careful when I entered the password. What should I do?

    Hi, unfortunately WEP is about as secure as a bar of gold lent to a Gang Den! It can be broken in under 30 seconds these days!
    If the PW is ASCII, try enclosing it in qoute marks, if Hex try preceding it with the & or % sign.
    Also, is the Router set to only allow connect ion to MAC addies of the Interface?

  • I recently added a wireless router and now am unable to get to the internet through Firefox.

    When I laucnch Firefox I get the following message: Firefox has detected that the server is redirecting the request for this address in a way that will never complete.
    This problem can sometimes be caused by disabling or refusing to accept
    cookies.
    Do I have to do something else now that I added the wireless router?

    From a previous post:
    Clear the Cookies for the Specific Site or Page you are having the problem connecting to - or if no sites will load, Clear All Cookies: http://support.mozilla.com/en-US/kb/Deleting%20cookies?s=clear+cookies&r=1&as=s

  • I connect my i-pad mini to my wireless router but when i try to use the internet i get a pop up saying "unable to connect with server. check your internet connection and try again i try and try it still wont work anybody know how to fix this

    I connect my i-pad mini to my wireless router and it says im connected but it wont let me do anything anybody know why ?

    You may not really be connected to your WiFi network.
    Your router may not have given your iPad a valid IP address. Go to Settings > Wifi > your network name and touch the ">" to the right to see the network details. If the IP address starts with 169 or is blank then your router didn't provide an IP address and you won't be able to access the Internet.
    Sometimes the fix can be as simple as restarting your router (remove power for 30 seconds and restart). Next, reset network settings on your iPad (Settings > General > Reset > Reset network settings) and then attempt to connect. In other cases it might be necessary to update the router's firmware with the latest from the manufacturer's support web pages.
    If you need more help please give more details on your network, i.e., your router make, model and version, the wifi security being used (WEP, WPA, WPA2), etc.

  • Wrt54g2 wireless router--unable to establish connectivity

    I have to unplug/replug my router powercord connection every time i want to use my laptop to access the internet.  i have reinstalled the software disc that came with my router.  i have have comcast check my modem--no problems. any suggestions?  do i need a new router?

    If that is the case then you can try the following steps:
    # Open up the browser and on the address bar type 192.168.1.1 that will open up the Router setup page…
    # Click on Wireless Tab and make the wireless channel to 6, 9 or 11. (These are considered to be the best)…
    # Click on the Advanced Wireless Settings change Beacon Interval to 75, Fragmentation Threshold to 2306, RTS Threshold to 2307...
    # After doing these settings check for the connectivity….
    Also, make sure that you do not have any interfering devices like Microwaves and cordless phones near the wireless router. These devices work on the same frequency as that of the router works…

  • P1102w 'unable to communicate with any wireless router or access point using the provided SSID

    For more than a 1 1/2 years I have been able to print wirelessly.  Prior to getting all set up, I was getting this message and had difficulty with the setup.  At that time I was under warrantly, I was able to get help from HP.  However, it took techs a very long time to figure out why I was receiving this message.  I somewhat recall doing something in the control panel and checking the SSID and password.
    I recently received a new wireless router and now my printer does not work wirelessy.  I can't figure it out!! 
    Anyone having the same probelm?

    Replacing your wireless router try here.
    http://www.hp.com/global/au/en/wireless/reconfiguring-system-help3.html
    Say thanks by clicking the Kudos Thumbs Up to the right in the post.
    If my post resolved your problem, please mark it as an Accepted Solution ...
    I worked for HP but now I'm retired!

  • Unable to connect to internet with my wireless router...... Shows Connected... Great signal...

    Hello, I really need some help.� 
    � 
    I have Verizon DSL and that works great when it is connected to my laptop with a network cable.� 
    � 
    I got a have a linksys wireless router (wrt54G)� �  and It works, � according to the network connections........ Connected and says the signal is great.
    � 
    � However when I an connected to my signal and I open up a browser window .... it says it cant find network....
    � 
    � I have reset the router...... and the Verizon modem....... 3 or four times........ I even went with the linksys step by step software CD twice.�  Nothing.....�  I can, however connect to my roommates wireless network, just fine.... but he is moving and taking his router with him so I need to get mine to work.
    � 
    I am new at the wireless networking thing so any hepl in laymans terms would be greatly appreciated.... thank you
    � 
    Melissa

    Ok......... finally fixed it.  seemingly, all that i needed to do was change my ip to 192.168.2.1.  WOW then it worked. 

  • Unable to maintain internet connection using wireless router

    I posted a bug report with Apple, 7229097. Not sure if anyone has been able to fix this. I tried the suggestions on the board (create location, reboot router, clean install, normal install, delete config etc.) I have narrowed the issue down to my router, which works fine under 10.5.8.
    Summary:
    I have trouble maintaining an internet connection using my Dell TrueMobile 1184 Wireless Broadband Router, model wx-6215D. If I connect directly to my cable modem, I have no internet issues. So, it seems the issue is using the Router, both wireless or using RJ45 cable.
    Steps to reproduce:
    Connect to my wireless router using Airport or RJ45. Browse to a page using Safari or Firefox. First page usually comes up, but is incomplete. Start using refresh or click on more pages, after 1 - 5 refreshes, clicking on links, you get a notice that you are no longer connected to the internet. If you open terminal and execute "dscacheutil -flushcache" you can get your internet back, but will degrade to no internet after 1 - 5 page refreshes.
    Expected result:
    Internet browsing should be fine
    Actual result:
    Internet degrades until browser reports no internet connection.
    Regression:
    Go back to 10.5.8 system and no problem exists. Only happens when you upgrade to 10.6 and 10.6.1.
    Notes:
    I have tried doing the recommended installation, and erasing the hard drive and installing - in both cases I have the same result. Router works fine for PC and 10.5.8. I have since installed 10.6.1 to a USB drive to do any further testing and would appreciate a patch or a timeline for a patch before I move my system to 10.6.1

    I tried adding in the OpenDNS ip 208.67.222.222, 208.67.220.220
    It appears that the router is hijacking DNS calls.
    Funny thing though, DNS is resoving through the router, .2.1
    nslookup apple.com
    ;; reply from unexpected source: 192.168.2.1#53, expected 208.67.222.222#53
    ;; reply from unexpected source: 192.168.2.1#53, expected 208.67.220.220#53
    Server: 192.168.2.1
    Address: 192.168.2.1#53
    Non-authoritative answer:
    Name: apple.com
    Address: 17.251.200.70
    So, the router is giving up the IP address. Also, even though Safari, Firefox and others report no internet, nslookupk continues to work. The router works, but 10.6.1 doesn't seem to like what it gets from the router. Also, not sure a firmware upgrade is required for the router, if there even is one, because it works with both of my PCs and my Mac running 10.5.8.

  • Why doesn't my E4200 wireless router show all attached devices when viewing the DHCP Client table?

    I recently installed some wireless IP cameras and when attempting to re-install a camera I went into the DHCP Client table to verify which IP a camera was using to set it up, but I could not...and still cannot see any of my cameras in the table even though I can access three of them directly through the IE web browser. I initially power cycled both the E4200 router and Motorola cable modem, and then later just the wireless router...but I still do not see the devices connected. I currently have 2.0.37 firmware even though I was told by Cisco support that there was a later version available, just before being informed that I do not have support available and could purchase it. I attempted to locate a newer version, but the online upgrade portion of the Cisco Connect software searched the net and then states that I have the latest version available. I also opened a Firefox browser to see if maybe my browser was causing issues, but the same limited table appears without all entries available. I even opened the Cisco Connect software on another laptop with the same limited results.
    Other than a factory reset, any suggestions to get me E4200 dual band wireless router to show all attached devices through the DHCP Client table as it previously did approximately two weeks ago? Thanks!

    barrysegal wrote:
    I recently installed some wireless IP cameras and when attempting to re-install a camera I went into the DHCP Client table to verify which IP a camera was using to set it up, but I could not...and still cannot see any of my cameras in the table even though I can access three of them directly through the IE web browser. I initially power cycled both the E4200 router and Motorola cable modem, and then later just the wireless router...but I still do not see the devices connected. I currently have 2.0.37 firmware even though I was told by Cisco support that there was a later version available, just before being informed that I do not have support available and could purchase it. I attempted to locate a newer version, but the online upgrade portion of the Cisco Connect software searched the net and then states that I have the latest version available. I also opened a Firefox browser to see if maybe my browser was causing issues, but the same limited table appears without all entries available. I even opened the Cisco Connect software on another laptop with the same limited results.
    Other than a factory reset, any suggestions to get me E4200 dual band wireless router to show all attached devices through the DHCP Client table as it previously did approximately two weeks ago? Thanks!
    It is strongly recommended that you upgrade the firmware to a smart wifi, which may resolve lot of bugs. You can also download the firmware here:
    E4200v2 Linksys Smart Wi-Fi Firmware11/19/2012
    Ver.2.1.39.145204
    Download
    18.3 MB

  • Wireless signal but unable to view web pages

    I have a WRT54G version 6 wireless router, it's security enabled and my XP laptop recognizes the signal and says I'm connected, excellent strength. Problem is that when I open IE no pages will load, if I connect the modem to my ethernet connection I can connect fine.
    Any ideas?

    I'm having the exact same problem.  This morning I went to the website to follow the directions from Easy Answers: How to set up PPPoE DSL connections with Linksys Router......just a great help this was...after all the plug/unplug/plug/computer off/on/off/on....When I clicked on IE icon to connect to the internet, All it Connected to was this LINKSYS page...couldn't go  any place else!!! 
     I've had to unplug everything and go back to the DSL modem direct to this PC to get on the internet to go to this link....Now, interesting it does make sence that both the modem and router can not have the same IP address, but if I change the router..what do I change it too???  May DSL works at 192.168.1.1 which is the same as the link I went too to get the Linksys page.  Thanks

  • Unable to conect Original Airport Card to password protected wireless route

    I am trying to connect a ClamShell notebook( OS 10.3.9) with an Apple Original Airport Card (installed) to a wireless router. When I access the network in System preferences, it detects the router and my Airport Card and indicates that a password is needed to access the that network. After inputting the password and with the location router highlighted, it does not connect me with the network as I go through the setup procedure. The system administrator successfully connected to the router with a PC laptop. Am I not selecting a topic that I should or have I not performed the set up procedure correctly? I did not have this problem when I connected to a non-password router.
    Any help would be greatly appreciated,
    Darrell

    Never received a reply from Henry B. so I decided to experiment with my problem. I Inputted the password in the Setup assistant, highlighted the router location and clicked Continue to continue with the Assistant. The Airport icon in the top bar became more pronounced instead of faded. I did not receive confirmation of a connection, in fact the back up page button was the only button active. I closed out of the Setup Assistant. I brought a browser and found the browser was connected to the Internet.
    MORAL: Don;t always believe the Setup Assistant

Maybe you are looking for