WLC problem

Hi Guys,
I’m trying to connect a 2504 WLC with cisco 1041 lightweight access points. I have a simple setup where my WAN link comes and terminate at a 2911 ISR router (where the DHCP pool is configured) and it connects to the internal switch in which both my WLC and access points(02) directly connected.
My problem is though I can see my 02 access points in the WLC’s GUI interface (under Monitor>CDP>interface neighbors) with ip addresses obtained from the DHCP pool. I can’t see any APs getting connected to the WLC.
Can anyone assist me with this regard?
Regards,
Suthakar

First off, make sure the time is set correctly on the WLC.  Place the AP's in the same subnet as the WLC management interface for now and make sure there is a dhcp scope on that subnet.  If you switchport is setup as an access port, then you need to make sure the wlc management interface is tagged with a vlan of "0".  If you have the switchport setup as at trunk port, then you can tag the wlc management interface with the vlan id.  Just make sure your not setting the native vlan on the trunk port and only allow the vlans you have defined on the WLC.

Similar Messages

  • ISE Airespace ACL WLC problem

    Hello,
    i've configured ISE and WLC to use guestportal with CWA but there is a problem with CoA -- it doesn't want to apply airespace alc after auth at guestportal.
    1. At authC page i've configured a wireless MAB to continue if user not found and to use a Internal users as a identity store.
    2. At authZ page i've configured a WEBAUTH as a default rule with the following:
    Access Type = ACCESS_ACCEPT
    cisco-av-pair = url-redirect-acl=ACL-WEBAUTH-REDIRECT
    cisco-av-pair = url-redirect=https://ip:port/guestportal/gateway?sessionId=SessionIdValue&action=cwa
    3. I've also configured this ACL at WLC to permit
    permit dns and icmp any-any
    permit any-to-ise-8443
    permit ise-to-any
    This part works fine because i able to redirect to guestportal and use my guest login&pw to authorize myself. The guest account was previously generated through sponsor portal and it's working too.
    4. At authC page i've use a wireless dot1x to use Internal users
    5. At authZ page i've use a "if internal users:Guest then GUEST permission" rule
    6. GUEST rule looks like the following:
    Access Type = ACCESS_ACCEPT
    Airespace-ACL-Name = GUEST_INTERNET_ONLY
    7. This ACL is configured on the WLC permitting any except private networks (ISE is also permitted)
    After guest portal auth i see a success message and i able to ping internet but i have no web access to it. It looks like CoA and Airespace acl are don't working and i keep using my ACL-WEBAUTH-REDIRECT access-list and i see a strange error messages in the WLC logs:
    *apfReceiveTask: Nov 12 17:32:27.317: %ACL-3-ENTRY_DONOT_EXIST: acl.c:369 Unable to find an ACL by name "".
    I swear my ACL name spelling is correct and both ACL-WEBAUTH-REDIRECT and GUEST_INTERNET_ONLY are on the WLC with their counters growing!
    I don't have a point what issue it could be...
    Any ideas?
    P.S. see attach for Live authentication log

    Thank you guys for your responses, it's working now!
    The first problem was there:
    Changing IPv4 ACL 'none' (ACL ID 255) ===> 'GUEST_INTERNET_ONLY' (ACL ID 5)
    There are only 3 ACLs on my WLC so ALC ID 5 is kinda suspicious -- after WLC reload it becames ACL ID 1 but the problem was unresolved.
    After that i changed my authZ matching rule to use another authZ profile:
    Access Type = ACCESS_ACCEPT
    Airespace-ACL-Name = PERMIT_ALL_TRAFFIC
    cisco-av-pair = Airespace:Airespace-ACL-Name
    Then i created ACL PERMIT_ALL_TRAFFIC on my WLC with one ACE "permit any any". I also denied access to my private networks at ASA where guest vlan's gateway resides.
    I think the problem was in WLC's GUEST_INTERNET_ONLY ACEs which denied traffic to my private networks.
    Thanks for the help!

  • Linksys PCI cards and WLC problems

    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:Standardowy;
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:11.0pt;
    font-family:"Calibri","sans-serif";
    mso-ascii-font-family:Calibri;
    mso-ascii-theme-font:minor-latin;
    mso-hansi-font-family:Calibri;
    mso-hansi-theme-font:minor-latin;
    mso-bidi-font-family:"Times New Roman";
    mso-bidi-theme-font:minor-bidi;
    mso-fareast-language:EN-US;}
    Hi,
    I have Linksys
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:Standardowy;
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:11.0pt;
    font-family:"Calibri","sans-serif";
    mso-ascii-font-family:Calibri;
    mso-ascii-theme-font:minor-latin;
    mso-hansi-font-family:Calibri;
    mso-hansi-theme-font:minor-latin;
    mso-bidi-font-family:"Times New Roman";
    mso-bidi-theme-font:minor-bidi;
    mso-fareast-language:EN-US;}
    WMP200 and WMP54G Wi-Fi PCI cards  installed on PC.
    My infrastructure is WLC 2106 and two APs 1231G and one 1242G.
    The problem is that the cards have problem with connection to WLAN.
    The broadcast SSID must be enable then the cards connect to WLAN otherwise is a problem with connection.
    When the card is connected but connection is unstable and poor.
    The cards have the newest firmware installed.
    Has anyone encountered a similar problem?
    Kamil

    Hi Kamil,
    Have you associated other types of clients with these AP's?  If so, do they perform better?
    You might want to start by checking the status of the poorly performing client on the controller while it's connected:
    monitor -> clients
    You'll primarily be interested in the RSSI and SNR. The other counters such as 'excessive retries' should be observed as well.
    Also check the AP's radio interface stats.  Check for excessive interference or channel utilization.
    This is a very helpful doc that you may want to check out:
    Unified Wireless Network: Troubleshoot Client  Issues
    http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00809d45a2.shtml
    Let us know if any of this helps.

  • WLC Problem 4.0 with mobile devices

    The problem is we have a WLC version 4.0 and have multiple SSIDs, but one has been created with WEP security is specific to the directors of the company. The scenario is that mobile devices (Blackberry, Iphone 4, IPad 2, etc) have connectivity problems
    One of the scenarios is not automatically sign the WIFI mobile devices and can only be after several attempts. Another scenario we have is that it takes over 15 seconds to take ip and be signed into the network. Finally, it is to tell us that after a while the devices are out of the WLAN and take again after several attempts to register or
    I hope I can guide
    GREETINGS!

    Marco,
    My recommendation is that you upgrade your controller to current software. 4.0 is ancient code.
    Justin

  • Migration to WLC Problems whit Phone 792X

    Hi,
    We have migrated from a Autonomous Wireless Solution (1200 AP) to Centralized Wireless LAN Controller (WLC 5500). The WLANs work fine, but the call on the Wireless Phone 7921, are experiencing problems, sound in one way, drop of calls, problems no present  previously with the autonoums solution. The QoS of the Voice WLAN is set to Voice, but the problems  persist. Any Suggestion ??

    It sounds RRM on the WLC may have changed your power levels on the APs.  One way audio is almost always caused by the power of the AP being set higher than the power on the phone.  Have a look at this deployment guide.
    http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7921g/6_0/english/deployment/guide/7921dply.pdf

  • WLC problem - Some LWAPP APs not working

    Dear All,
    Our WLC 4402 and 46 1130AG Access points in LWAPP mode have been working flawlesly for the past few years, but suddenly this week some access points have not been working (but the rest are fine). They are correctly registered on the WLC, but if anyone tries to connect they get an authentication failrue and the WLC logs the following. Nothing on the WLC has changed, the only thing that's changed on the network is a new firewall (the WIFI network is one of the subnets) but that shouldn't affect whether users can connect to the WIFI network. Anyone have any clues as to what's going on?
    Log System Time Trap
    0
    Thu Jun 16 10:29:57 2011
    Client Deauthenticated: MACAddress:00:1f:c5:f3:84:75 Base Radio MAC:00:1d:e5:4e:95:70 Slot: 0 Reason:Unspecified  ReasonCode: 1
    1
    Thu Jun 16 10:29:14 2011
    Client Deauthenticated: MACAddress:5c:59:48:55:74:49 Base Radio MAC:00:1d:e5:4e:93:80 Slot: 0 Reason:Unspecified  ReasonCode: 1
    2
    Thu Jun 16 10:28:54 2011
    Client Deauthenticated: MACAddress:5c:59:48:55:74:49 Base Radio MAC:00:1d:e5:4e:93:80 Slot: 0 Reason:Unspecified  ReasonCode: 1
    3
    Thu Jun 16 10:20:59 2011
    Decrypt errors occurred for client 04:1e:64:33:2b:d0 using WPA key on 802.11b/g interface of AP 00:1d:e5:4d:f1:f0
    4
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:d8:9e:3f:aa:ae:18 Base Radio MAC:00:13:5f:f9:a7:10 Slot: 0 Reason:Unspecified  ReasonCode: 1
    5
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:c4:2c:03:3f:92:c0 Base Radio MAC:00:1d:e5:4d:f1:f0 Slot: 0 Reason:Unspecified  ReasonCode: 1
    6
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:b4:07:f9:f3:87:7e Base Radio MAC:00:13:5f:fb:1b:e0 Slot: 0 Reason:Unspecified  ReasonCode: 1
    7
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:90:27:e4:b2:da:b1 Base Radio MAC:00:1d:e5:4e:8a:50 Slot: 0 Reason:Unspecified  ReasonCode: 1
    8
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:88:c6:63:c3:47:92 Base Radio MAC:00:1d:e5:4d:f1:f0 Slot: 0 Reason:Unspecified  ReasonCode: 1
    9
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:7c:c5:37:14:f0:bb Base Radio MAC:00:1d:e5:4e:92:d0 Slot: 0 Reason:Unspecified  ReasonCode: 1
    10
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:78:ca:39:88:c2:a3 Base Radio MAC:00:1d:e5:4e:93:10 Slot: 0 Reason:Unspecified  ReasonCode: 1
    11
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:5c:59:48:55:74:49 Base Radio MAC:00:1d:e5:4d:f1:f0 Slot: 0 Reason:Unspecified  ReasonCode: 1

    What kind of authentication i being used on SSID that the clients connect to? If RADIUS server is involved, can you verify if it shows any logs pointing to auth failure?
    Run a debug client on the controller for one problem client and send it over.

  • WLC problem, any Help?

    Hi,
    I've got a problem with our WLC 4402.
    We have a big network with only Cisco devices (routers, switches, wlc's ....). every thing is running fantastic a part from the following issue:
    I've a lot of Vlans, one of them called AVlan. if I connect devices  anywhere in the building  (pcs, laptops,.....) to this Vlan "using wired connections /cat5 cables" , all devices can see each other and transfare files, documents among them, but if I connect the same devices using the same Vlan (Avlan) but through wireless system, non of the devices can see anyother "connected" device (every pc can see only it's shared folders)!!!!. I've checked everything on the wireless controller (4402-25) but can't find the reason for this issue. It is very important for us to get all  devices connected to this Vlan to be able to "talk to eachother" because we have a file server in the same Vlan,which we use for transfering files from / to this server and among the devices on the same Vlan ( as I mentioned before it workes perfectly on wired network on the same Vlan).
    Any help please
    Mny thanks
    Ali

    Many thanks for all your help, and sorry for the delay (I was not at work for the last 4 days)
    The vlan I have problems with (only wireless) is the vlan 208
    Please find below the onfiguration of the distribution and core switches:
    The vlan 502 in the distribution switch because we use this vlan for our wireless voucher system
    Core switch:
    interface GigabitEthernet1/0/12
    description Wifi Ctrlr
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 1,201,203,208,211,214,499-510,600
    switchport mode trunk
    channel-group 4 mode on
    Distribution switch:
    interface FastEthernet1/0/23
    description *** WIFI_AP_HALL-B_CLOSE-TO-HALL-A ***
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 1,502
    switchport mode trunk
    interface FastEthernet1/0/24
    description *** WIFI_AP_HALL-B_MIDDLE-OF-HALL-B ***
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 1,502
    switchport mode trunk
    Does anybody think that I have to add Vlan 208 to the distribution switch as a trunk (
    switchport trunk allowed vlan 1,502)?
    Many thanks to everybody

  • SNMP Discovery of clients through WLC problems

    I have a client with a 2112 WLC and 1252AG radios. The clients work fine, but an SNMP management server can not reach any of the clients over the wireless. Before the WLC and new AP's were installed, they were running older Cisco Autonomous AP's and had no problems with SNMP.  My monitoring system uses SNMP and it can reach the WLC just fine, so there doesnt appear to be any issues on the switched network.
    What can be blocking the SNMP on the WLC?

    the WLC, by default doesn't communicate when you bridge the VLANs. Do the clients need to be in the same subnet as the SNMP server? If not, remove the interface and they should be able to communicate.
    If they do need to hVe in that subnet, then you need to enable management via dynamic interface
    Config network mgmt-via-dynamic-interface enable
    Sent from Cisco Technical Support iPhone App

  • WISM and NAC OOB/ Client in a different WLC problem

    Guys,
    I am using two WiSM modules in 6513 Chassi.
    We have 3 SSID configured but on each WLC  are using APGroups making a Layer 3 roaming.
    Well, Everything is work out fine and we have hundreds of the connections per day but each day appear two or three clients that still on Quarantine mode and the WLC does not change Auth_vlan to Access_Vlan.
    NAC appear that client as ONLINE on WLC 3 but that client isn't  there, he is on WLC 2 in Quarantine mode.
    anyone know can help me?
    thanks a lot

    I think the jndi service can be accessed froma remote m/c, you can initialize the context with the appropriate paramters, so the lookups on the topic and connection factories and continue with your work.

  • ISE guestaccess - Android/iPad problem

    Hi all,
    I have a guestaccess using CWA on ISE 1.1.1 and WLC 7.2
    The setup is realy simple with redirect ACL to ISE and after that an permit-all ACL.
    Guest users are on a guest vlan and go thru a ASA to talk to DHCP, DNS and ISE.
    When I try to connect with laptops, Windows 7, OSX 10.7 and 10.8, it works like it a charm.
    The user gets redirected, put in credentials and after that get on the network. Not one problem out of maybe 30 tests.
    But when I try smartphones and iPad it doesent work that well...
    With iPhones, iOS5 and iOS 6 tested on three diffrent phones, I get access 19/20 times.
    With iPad, only one with iOS 5.1, I get access maybe 50% of the tries
    And with Android, two HTC with 2.3.7 and 2.3.3, I got one logon to the guest network out of 25 or more tries.
    What happends when I try to access the network with a problem device is that it gets a redirect url but states,
    on Android 'Web page not available' and on iPAD '..could not open page because it could not connect ot server.
    On all these devices I can see that I have a DHCP lease with IP address and DNS. I have rebooted all devices several times and I have used 'forget this network' on the diveces.
    I have also tried to removed the clients from the WLC and I have tried to turn off/on the WLAN on the WLC.
    Could this be a WLC problem? I did a simple TCP dump on the ISE server but did not see any packets. (Need to do this one again..)
    Anyone with some insight on guestaccess and mobile devices? :-)
    Message was edited by: Mikael Gustafsson

    While authenticating  the guest through wireless  its very important to check all the compatibility issues of the client  with the NAC(Switch/WLC) device and ISE.Please check the below  compatibitility matrix link along with some other links for assistance  on your queries:
    http://www.cisco.com/en/US/docs/security/ise/1.1.1/compatibility/ise_sdt.html
    http://www.cisco.com/en/US/solutions/collateral/ns340/ns414/ns742/ns744/docs/howto_40_webauthentication_dg.pdf
    http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bead09.shtml

  • WLC 5760 - AP2600i failed to join ap-group after reboot

    Hi,
    We're deploying a couple of 2600i with an WLC 5760.
    We've configured an AP group, named it "factory", and then issued the command ap name AP<ip mac address> ap-groupname factory for both APs. After the restart, both AP were on the AP-Group factory.
    The problem is that is we reboot or power off the APs, one will join automatically the AP-Group factory and the other goes to default-group and requires the ap name APAPf872.ead7.31da ap-groupname factory to join the AP group factory again.
    Any suggestion? Is it possible to forced the ap-group configuration directly on the cli of the AP?
    WLC1#sh ap groups
    Site Name: default-group
    Site Description:
    WLAN ID   WLAN Name                        Interface
    AP Name                          Slots AP Model             Ethernet MAC      Location      Port                   Country Priority GroupName
    Site Name: factory
    Site Description:
    WLAN ID   WLAN Name                        Interface               Radio
    AP Name                          Slots AP Model             Ethernet MAC      Location      Port                   Country Priority
    APf872.eaa6.fc69                 2     2602I                f872.eaa6.fc69 default location Te1/0/1                PT      1      
    APf872.ead7.31da                 2     2602I                f872.ead7.31da default location Te1/0/1                PT      1      
    debug ap group
    (AP joining the apgoup factory)
    Sep 17 18:24:24.420: apfRadioPolicySiteTableEntryGet: 1 wcm:  found radio Policy 7 for apVapId 1 for ap APf872.eaa6.fc69  apgroup factory
    Sep 17 18:24:24.420: apfRadioPolicySiteTableEntryGet: 1 wcm:  found radio Policy 7 for apVapId 2 for ap APf872.eaa6.fc69  apgroup factory
    Sep 17 18:24:24.420: apfRadioPolicySiteTableEntryGet: 1 wcm:  found radio Policy 7 for apVapId 3 for ap APf872.eaa6.fc69  apgroup factory
    Sep 17 18:24:24.420: apfRadioPolicySiteTableEntryGet: 1 wcm:  found radio Policy 7 for apVapId 4 for ap APf872.eaa6.fc69  apgroup factory
    Sep 17 18:24:24.420: apfRadioPolicySiteTableEntryGet: 1 wcm:  found radio Policy 7 for apVapId 5 for ap APf872.eaa6.fc69  apgroup factory
    Sep 17 18:24:24.420: apfRadioPolicySiteTableEntryGet: 1 wcm:  found radio Policy 7 for apVapId 6 for ap APf872.eaa6.fc69  apgroup factory
    Sep 17 18:24:24.420: apfRadioPolicySiteTableEntryGet: 1 wcm:  found radio Policy 7 for apVapId 7 for ap APf872.eaa6.fc69  apgroup factory
    (AP joining the default-group)
    Sep 17 18:30:36.078: apfRadioPolicySiteTableEntryGet: 1 wcm:  found radio Policy 0 for apVapId 1 for ap APf872.ead7.31da  apgroup default-group
    Sep 17 18:30:36.078: apfRadioPolicySiteTableEntryGet: 1 wcm:  found radio Policy 0 for apVapId 2 for ap APf872.ead7.31da  apgroup default-group
    Sep 17 18:30:36.078: apfRadioPolicySiteTableEntryGet: 1 wcm:  found radio Policy 0 for apVapId 3 for ap APf872.ead7.31da  apgroup default-group
    Sep 17 18:30:36.078: apfRadioPolicySiteTableEntryGet: 1 wcm:  found radio Policy 7 for apVapId 4 for ap APf872.ead7.31da  apgroup default-group
    Sep 17 18:30:36.078: apfRadioPolicySiteTableEntryGet: 1 wcm:  found radio Policy 0 for apVapId 5 for ap APf872.ead7.31da  apgroup default-group
    Sep 17 18:30:36.078: apfRadioPolicySiteTableEntryGet: 1 wcm:  found radio Policy 0 for apVapId 6 for ap APf872.ead7.31da  apgroup default-group
    Kind regards,
    Vasco Costa

    We've used a another group of 2600i APs and it seems that this problem only occous with AP "APf872.ead7.31da" so this is not a WLC problem.
    closing case

  • From WCS download webauthcer to WLC.

    Hi,
    Is possible from WCS to download a webauthcer on WLC?
    With WCS is possible to download the device cert that is not a webauthcer and CA cert but I don't see the webauthcer?
    Regards.
    Miko Severi

    I dont advise you to start with the DB this is not DB related problem at first sight.
    First of, your WLC version is too new to be supported for the WCS version you have as per release notes:
    http://www.cisco.com/en/US/docs/wireless/wcs/release/notes/WCS_RN6_0.html
    That WCS only supports WLC 6.0.182.0 max.
    For later WLC, you need to upgrade WCS.
    Fix that first. You can upgrade WCS during production, it's not having an impact on the WLC.
    Then FYI, for troubleshooting SNMP / WCS / WLC problems, look at my video. I also cover the upgrade steps for WCS:
    https://supportforums.cisco.com/community/netpro/ask-the-expert/webcasts
    or for bigger size:
    http://www.youtube.com/watch?v=0KQUfszmTJg
    Please support CSC Helps Haiti
    https://supportforums.cisco.com/docs/DOC-8895
    https://supportforums.cisco.com

  • Problem with certificate authentication at wlc 4402

    Hi,
    we have a problem to get a connection from the client to the WLC. 
    we  are using Cisco Aironet 1130 AG and a Cisco 4402 WLC in our network. The certificate service is installed on a Windows 2008 R2 server. We use a standalone Root CA with a Enterprise Sub CA hierarchy. Issueing certificates to clients works fine. The vendor and ca certificates are installed on the WLC and the user have his user certificate. During implementation we used following document: "http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a008093f1b9.shtml#wlc". Instead of Anonymous Bind, we use a service user to read in AD (works fine, too).
    We use the Intel/PRO wireless utility on our Testclient and configured it for EAP-FAST and TLS. We can select the installed certificate in the utility, but when we try to connect, the utility throw the message: "Authentication failed due to an invalid certificate".
    We´ve logged the WLC and thats a part of the logfile (i´ve greyed out all enterprise data):
    *EAP Framework: Jan 18 12:08:21.921: EAP-AUTH-EVENT: Waiting for asynchronous reply from LL
    *LDAP DB Task 1: Jan 18 12:08:21.921: ldapTask [1] received msg 'REQUEST' (2) in state 'IDLE' (1)
    *LDAP DB Task 1: Jan 18 12:08:21.922: LDAP server 1 changed state to INIT
    *LDAP DB Task 1: Jan 18 12:08:21.922: LDAP_OPT_REFERRALS = -1*LDAP DB Task 1: Jan 18 12:08:21.925: LDAP_CLIENT: UID Search (...)))
    *LDAP DB Task 1: Jan 18 12:08:21.926: LDAP_CLIENT: ldap_search_ext_s returns 0 85
    *LDAP DB Task 1: Jan 18 12:08:21.926: LDAP_CLIENT: Returned 2 msgs including 0 references
    *LDAP DB Task 1: Jan 18 12:08:21.926: LDAP_CLIENT: Returned msg 1 type 0x64
    *LDAP DB Task 1: Jan 18 12:08:21.926: LDAP_CLIENT: Received 1 attributes in search entry msg
    *LDAP DB Task 1: Jan 18 12:08:21.927: LDAP_CLIENT: Returned msg 2 type 0x65
    *LDAP DB Task 1: Jan 18 12:08:21.927: LDAP_CLIENT : No matched DN
    *LDAP DB Task 1: Jan 18 12:08:21.927: LDAP_CLIENT : Check result error 0 rc 1013
    *LDAP DB Task 1: Jan 18 12:08:21.927: LDAP_CLIENT: Received no referrals in search result msg
    *LDAP DB Task 1: Jan 18 12:08:21.927: ldapAuthRequest [1] called lcapi_query base="..." (rc = 0 - Success)
    *LDAP DB Task 1: Jan 18 12:08:21.927: LDAP ATTR> dn = CN=... (size 76)
    *LDAP DB Task 1: Jan 18 12:08:21.927: Handling LDAP response Success
    *LDAP DB Task 1: Jan 18 12:08:21.927: 18:3d:a2:0a:ec:bc [Response] Client requested no retries for mobile 18:3D:A2:0A:EC:BC
    *LDAP DB Task 1: Jan 18 12:08:21.927: 18:3d:a2:0a:ec:bc Returning AAA Success for mobile 18:3d:a2:0a:ec:bc
    *LDAP DB Task 1: Jan 18 12:08:21.927: AuthorizationResponse: 0x33a5affc*LDAP DB Task 1: Jan 18 12:08:21.928: LOCAL_AUTH: Found context matching MAC address - 319
    *LDAP DB Task 1: Jan 18 12:08:21.928: LOCAL_AUTH: (EAP:319) User credential callback invoked
    *LDAP DB Task 1: Jan 18 12:08:21.928: LOCAL_AUTH: EAP Unable to find password in credentials. Skipped
    *LDAP DB Task 1: Jan 18 12:08:21.928: LOCAL_AUTH: EAP Unable to find wlan in credentials. Skipped
    *LDAP DB Task 1: Jan 18 12:08:21.928: Authenticated bind : Closing the binded session*LDAP DB Task 1: Jan 18 12:08:21.928: ldapClose [1] called lcapi_close (rc = 0 - Success)
    *LDAP DB Task 1: Jan 18 12:08:21.929: LDAP server 1 changed state to IDLE
    *EAP Framework: Jan 18 12:08:21.930: EAP-EVENT: Received event 'EAP_LL_REPLY' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:21.930: EAP-AUTH-EVENT: Using credential profile name: ...(0x78000041)
    *EAP Framework: Jan 18 12:08:21.930: EAP-AUTH-EVENT: Maximum EAP packet size: 1000
    *EAP Framework: Jan 18 12:08:21.930: EAP-AUTH-EVENT: Sending method new context directive for EAP context 0x78000041
    *EAP Framework: Jan 18 12:08:21.930: EAP-EVENT: Sending method directive 'New Context' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:21.930: eap_fast.c-EVENT: New context (EAP handle = 0x78000041)
    *EAP Framework: Jan 18 12:08:21.931: id_manager.c-AUTH-SM: Got new ID f700000e - id_get
    *EAP Framework: Jan 18 12:08:21.931: eap_fast.c-EVENT: Allocated new EAP-FAST context (handle = 0xF700000E)
    *EAP Framework: Jan 18 12:08:21.931: EAP-AUTH-EVENT: Sending method data for context 0x78000041
    *EAP Framework: Jan 18 12:08:21.931: EAP-EVENT: Sending method directive 'Receive Packet' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:21.931: eap_fast_auth.c-AUTH-EVENT: Process Response (EAP handle = 0x78000041)
    *EAP Framework: Jan 18 12:08:21.931: eap_fast_auth.c-AUTH-EVENT: Received Identity
    *EAP Framework: Jan 18 12:08:21.931: eap_fast_tlv.c-AUTH-EVENT: Adding PAC A-ID TLV (436973636f0000000000000000000000)
    *EAP Framework: Jan 18 12:08:21.931: eap_fast_auth.c-AUTH-EVENT: Sending Start
    *EAP Framework: Jan 18 12:08:21.931: eap_fast_auth.c-AUTH-SM: Changing state: Reset -> Start
    *EAP Framework: Jan 18 12:08:21.931: eap_fast.c:2367: eap-fast tx packet:
    *EAP Framework: Jan 18 12:08:21.931: eap_fast.c:138: Version: 1  Flags:S  Length:0x0014
    *EAP Framework: Jan 18 12:08:21.931: eap_core.c:1422:     Payload:  00040010436973636F00000000000000 ...
    *EAP Framework: Jan 18 12:08:21.931: eap_fast.c-TX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:21.931: eap_core.c:1484: Code:REQUEST  ID:0x 0  Length:0x001a  Type:FAST
    *EAP Framework: Jan 18 12:08:21.932: eap_core.c:1422:     Payload:  2100040010436973636F000000000000 ...
    *EAP Framework: Jan 18 12:08:21.932: EAP-AUTH-EVENT: EAP method state: Continue
    *EAP Framework: Jan 18 12:08:21.932: EAP-AUTH-EVENT: EAP method decision: Unknown
    *EAP Framework: Jan 18 12:08:21.932: EAP-AUTH-EVENT: Current method = 43
    *EAP Framework: Jan 18 12:08:21.932: EAP-AUTH-EVENT: Sending packet to lower layer for context 0x78000041
    *EAP Framework: Jan 18 12:08:21.932: EAP-AUTH-TX-PAK:
    *EAP Framework: Jan 18 12:08:21.932: eap_core.c:1484: Code:REQUEST  ID:0x 2  Length:0x001a  Type:FAST
    *EAP Framework: Jan 18 12:08:21.932: eap_core.c:1422:     Payload:  2100040010436973636F000000000000 ...
    *EAP Framework: Jan 18 12:08:21.932: EAP-EVENT: Started 'Authenticator Retransmit' timer (60) for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:21.932: EAP-EVENT: Started EAP tick timer
    *EAP Framework: Jan 18 12:08:21.932: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:21.932: LOCAL_AUTH: Found matching context for id - 319
    *EAP Framework: Jan 18 12:08:21.932: LOCAL_AUTH: (EAP:319) transmit event
    *EAP Framework: Jan 18 12:08:21.932: AuthorizationResponse: 0x13c713fc*EAP Framework: Jan 18 12:08:21.934: LOCAL_AUTH: AAA LOCAL AUTH EAP PKT AVP attribute 4f length 1a
    *EAP Framework: Jan 18 12:08:21.934: LOCAL_AUTH: AAA LOCAL AUTH TX PKT DUMP code cc id 00 type 2b
    *aaaQueueReader: Jan 18 12:08:22.290: LOCAL_AUTH: EAP: Received an auth request
    *aaaQueueReader: Jan 18 12:08:22.290: LOCAL_AUTH: Found context matching MAC address - 319
    *aaaQueueReader: Jan 18 12:08:22.290: LOCAL_AUTH: (EAP:319) Sending the Rxd EAP packet (id 2) to EAP subsys
    *EAP Framework: Jan 18 12:08:22.291: EAP-EVENT: Received event 'EAP_RX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.291: EAP-AUTH-RX-PAK:
    *EAP Framework: Jan 18 12:08:22.291: eap_core.c:1484: Code:RESPONSE  ID:0x 2  Length:0x0042  Type:FAST
    *EAP Framework: Jan 18 12:08:22.291: eap_core.c:1422:     Payload:  810000003816030100330100002F0301 ...
    *EAP Framework: Jan 18 12:08:22.291: EAP-EVENT: Stopping 'Authenticator Retransmit' timer for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.291: EAP-AUTH-EVENT: EAP Response received by context 0x78000041
    *EAP Framework: Jan 18 12:08:22.291: EAP-AUTH-EVENT: EAP Response type = Method (43)
    *EAP Framework: Jan 18 12:08:22.291: EAP-AUTH-EVENT: Sending method data for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.292: EAP-EVENT: Sending method directive 'Receive Packet' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.292: eap_fast.c-AUTH-EVENT: Process Response, type: 0x2b
    *EAP Framework: Jan 18 12:08:22.292: eap_fast_auth.c-AUTH-EVENT: Process Response (EAP handle = 0x78000041)
    *EAP Framework: Jan 18 12:08:22.292: eap_fast_auth.c-RX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:22.292: eap_core.c:1484: Code:RESPONSE  ID:0x 2  Length:0x0042  Type:FAST
    *EAP Framework: Jan 18 12:08:22.292: eap_core.c:1422:     Payload:  810000003816030100330100002F0301 ...
    *EAP Framework: Jan 18 12:08:22.292: eap_fast_auth.c-AUTH-EVENT: Received TLS record type: Handshake in state: Start
    *EAP
    Framework: Jan 18 12:08:22.292: EAP-EVENT: Sending lower layer event
    'EAP_GET_CREDENTIAL_PROFILE_FROM_PROFILE_NAME' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.292: LOCAL_AUTH: Found matching context for id - 319
    *EAP
    Framework: Jan 18 12:08:22.292: LOCAL_AUTH: (EAP:319) Returning profile
    *EAP Framework: Jan 18 12:08:22.293: IOS_PKI_SHIM: [StartSession] - New session 0x335ee108 started (TP = 'vendor')
    *EAP Framework: Jan 18 12:08:22.293: IOS_PKI_SHIM: [StartSession] - Trustpoint identity (cert) set to 'Vendor'
    *EAP
    Framework: Jan 18 12:08:22.297: IOS_PKI_SHIM: [ID-CERT] Subject : ...
    *EAP Framework: Jan 18
    12:08:22.297: IOS_PKI_SHIM: [ID-CERT] Issuer : ...
    *EAP Framework: Jan 18
    12:08:22.297: IOS_PKI_SHIM: [ID-CERT] Valid from '2012 Jan 12th,
    17:06:50 GMT' to '2016 Jan 11th, 17:06:50 GMT'
    *EAP Framework: Jan 18 12:08:22.297: IOS_PKI_SHIM: [ID-CERT] Is not a CA cert
    *EAP Framework: Jan 18 12:08:22.297: IOS_PKI_SHIM: Added cert (type 1) to chain (1 present on chain)
    *EAP
    Framework: Jan 18 12:08:22.300: IOS_PKI_SHIM: [CA-CERT] Subject :
    *EAP Framework: Jan 18 12:08:22.301: IOS_PKI_SHIM: [CA-CERT] Issuer : CN=...
    *EAP
    Framework: Jan 18 12:08:22.301: IOS_PKI_SHIM: [CA-CERT] Valid from
    '2012 Jan 12th, 16:54:49 GMT' to '2020 Jan 12th, 17:04:49 GMT'
    *EAP Framework: Jan 18 12:08:22.301: IOS_PKI_SHIM: [CA-CERT] Is a CA cert
    *EAP Framework: Jan 18 12:08:22.301: IOS_PKI_SHIM: Added cert (type 2) to chain (2 present on chain)
    *EAP Framework: Jan 18 12:08:22.301: IOS_PKI_SHIM: [StartSession] - Getting older style priv key
    *EAP Framework: Jan 18 12:08:22.338: IOS_PKI_SHIM: Session 0x335ee108 init'd OK
    *EAP Framework: Jan 18 12:08:22.338: eap_fast_auth.c-AUTH-EVENT: Local certificate found
    *EAP Framework: Jan 18 12:08:22.339: eap_fast_auth.c-AUTH-EVENT: Reading Client Hello handshake
    *EAP Framework: Jan 18 12:08:22.339: eap_fast.c:286: EAP-FAST-AUTH-RX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.339: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x0033
    *EAP Framework: Jan 18 12:08:22.339: eap_core.c:1422:     Payload:  0100002F03014F16A8262631FC9DC042 ...
    *EAP Framework: Jan 18 12:08:22.340: eap_fast.c:202: Handshake type:Client Hello  Length:0x002F
    *EAP Framework: Jan 18 12:08:22.340: eap_core.c:1422:     Payload:  03014F16A8262631FC9DC042253D3E24 ...
    *EAP Framework: Jan 18 12:08:22.340: eap_fast_auth.c-AUTH-EVENT: TLS_RSA_WITH_AES_128 proposed...
    *EAP Framework: Jan 18 12:08:22.341: eap_fast_auth.c-AUTH-EVENT: TLS_DHE_RSA_WITH_AES_128_CBC_SHA proposed...
    *EAP Framework: Jan 18 12:08:22.341: eap_fast_auth.c-AUTH-EVENT: TLS_RSA_WITH_RC4_128 proposed...
    *EAP Framework: Jan 18 12:08:22.341: eap_fast_auth.c-AUTH-EVENT: TLS_DH_anon_WITH_AES_128_CBC_SHA proposed...
    *EAP Framework: Jan 18 12:08:22.342: eap_fast.c-EVENT: Proposed ciphersuite(s):
    *EAP Framework: Jan 18 12:08:22.342: eap_fast.c-EVENT:     TLS_RSA_WITH_AES_128_CBC_SHA
    *EAP Framework: Jan 18 12:08:22.342: eap_fast.c-EVENT:     TLS_DHE_RSA_WITH_AES_128_CBC_SHA
    *EAP Framework: Jan 18 12:08:22.342: eap_fast.c-EVENT:     TLS_RSA_WITH_RC4_128_SHA
    *EAP Framework: Jan 18 12:08:22.343: eap_fast.c-EVENT:     TLS_DH_anon_WITH_AES_128_CBC_SHA
    *EAP Framework: Jan 18 12:08:22.343: eap_fast.c-EVENT: Selected ciphersuite:
    *EAP Framework: Jan 18 12:08:22.343: eap_fast.c-EVENT:     TLS_DHE_RSA_WITH_AES_128_CBC_SHA
    *EAP Framework: Jan 18 12:08:22.343: eap_fast_auth.c-AUTH-EVENT: Building Provisioning Server Hello
    *EAP Framework: Jan 18 12:08:22.344: eap_fast.c:286: EAP-FAST-AUTH-TX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.344: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x002A
    *EAP Framework: Jan 18 12:08:22.344: eap_core.c:1422:     Payload:  0200002603015F3325EADF12E6296F91 ...
    *EAP Framework: Jan 18 12:08:22.344: eap_fast.c:202: Handshake type:Server Hello  Length:0x0026
    *EAP Framework: Jan 18 12:08:22.345: eap_core.c:1422:     Payload:  03015F3325EADF12E6296F91530FE67F ...
    *EAP Framework: Jan 18 12:08:22.345: eap_fast.c:286: EAP-FAST-AUTH-TX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.345: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x0B54
    *EAP Framework: Jan 18 12:08:22.346: eap_core.c:1422:     Payload:  0B000B50000B4D00059F3082059B3082 ...
    *EAP Framework: Jan 18 12:08:22.346: eap_fast.c:202: Handshake type:Certificate  Length:0x0B50
    *EAP Framework: Jan 18 12:08:22.346: eap_core.c:1422:     Payload:  000B4D00059F3082059B30820483A003 ...
    *EAP Framework: Jan 18 12:08:22.347: eap_fast_crypto.c-EVENT: Starting Diffie Hellman phase 1 ...
    *EAP Framework: Jan 18 12:08:22.661: eap_fast_crypto.c-EVENT: Diffie Hellman phase 1 complete
    *EAP Framework: Jan 18 12:08:22.677: IOS_PKI_SHIM: PKI_SignMessage PostHashEncrypt ret SUCCESS.. op_len 128
    *EAP Framework: Jan 18 12:08:22.678: eap_fast_auth.c-AUTH-EVENT: DH signature length = 128
    *EAP Framework: Jan 18 12:08:22.678: eap_fast.c:286: EAP-FAST-AUTH-TX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.678: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x028D
    *EAP Framework: Jan 18 12:08:22.679: eap_core.c:1422:     Payload:  0C0002890100FFFFFFFFFFFFFFFFC90F ...
    *EAP Framework: Jan 18 12:08:22.679: eap_fast.c:202: Handshake type:Server Key Exchange  Length:0x0289
    *EAP Framework: Jan 18 12:08:22.679: eap_core.c:1422:     Payload:  0100FFFFFFFFFFFFFFFFC90FDAA22168 ...
    *EAP Framework: Jan 18 12:08:22.679: eap_fast.c:286: EAP-FAST-AUTH-TX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.680: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x000B
    *EAP Framework: Jan 18 12:08:22.680: eap_core.c:1422:     Payload:  0D00000704030401020000
    *EAP Framework: Jan 18 12:08:22.680: eap_fast.c:202: Handshake type:Certificate Request  Length:0x0007
    *EAP Framework: Jan 18 12:08:22.680: eap_core.c:1422:     Payload:  04030401020000
    *EAP Framework: Jan 18 12:08:22.681: eap_fast.c:286: EAP-FAST-AUTH-TX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.681: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x0004
    *EAP Framework: Jan 18 12:08:22.681: eap_core.c:1422:     Payload:  0E000000
    *EAP Framework: Jan 18 12:08:22.681: eap_fast.c:202: Handshake type:Server Done  Length:0x0000
    *EAP Framework: Jan 18 12:08:22.682: eap_fast_auth.c-AUTH-EVENT: Sending Provisioning Serving Hello
    *EAP Framework: Jan 18 12:08:22.682: eap_fast_auth.c-AUTH-SM: Changing state: Start -> Sent provisioning Server Hello
    *EAP Framework: Jan 18 12:08:22.682: eap_fast.c-EVENT: Tx packet fragmentation required
    *EAP Framework: Jan 18 12:08:22.683: eap_fast.c:2367: eap-fast tx packet:
    *EAP Framework: Jan 18 12:08:22.683: eap_fast.c:138: Version: 1  Flags:LM  Length:0x03DE
    *EAP Framework: Jan 18 12:08:22.683: eap_core.c:1422:     Payload:  160301002A0200002603015F3325EADF ...
    *EAP Framework: Jan 18 12:08:22.684: eap_fast.c-TX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:22.684: eap_core.c:1484: Code:REQUEST  ID:0x 0  Length:0x03e8  Type:FAST
    *EAP Framework: Jan 18 12:08:22.684: eap_core.c:1422:     Payload:  C100000E33160301002A020000260301 ...
    *EAP Framework: Jan 18 12:08:22.684: EAP-AUTH-EVENT: EAP method state: Continue
    *EAP Framework: Jan 18 12:08:22.685: EAP-AUTH-EVENT: EAP method decision: Unknown
    *EAP Framework: Jan 18 12:08:22.685: EAP-AUTH-EVENT: Current method = 43
    *EAP Framework: Jan 18 12:08:22.685: EAP-AUTH-EVENT: Sending packet to lower layer for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.685: EAP-AUTH-TX-PAK:
    *EAP Framework: Jan 18 12:08:22.685: eap_core.c:1484: Code:REQUEST  ID:0x 3  Length:0x03e8  Type:FAST
    *EAP Framework: Jan 18 12:08:22.686: eap_core.c:1422:     Payload:  C100000E33160301002A020000260301 ...
    *EAP Framework: Jan 18 12:08:22.686: EAP-EVENT: Started 'Authenticator Retransmit' timer (60) for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.686: EAP-EVENT: Started EAP tick timer
    *EAP Framework: Jan 18 12:08:22.686: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.686: LOCAL_AUTH: Found matching context for id - 319
    *EAP Framework: Jan 18 12:08:22.687: LOCAL_AUTH: (EAP:319) transmit event
    *EAP Framework: Jan 18 12:08:22.687: AuthorizationResponse: 0x13c713fc*EAP Framework: Jan 18 12:08:22.755: LOCAL_AUTH: AAA LOCAL AUTH EAP PKT AVP attribute 4f length 297
    *EAP Framework: Jan 18 12:08:22.755: LOCAL_AUTH: AAA LOCAL AUTH TX PKT DUMP code cc id 00 type 2b
    *aaaQueueReader: Jan 18 12:08:22.830: LOCAL_AUTH: EAP: Received an auth request
    *aaaQueueReader: Jan 18 12:08:22.830: LOCAL_AUTH: Found context matching MAC address - 319
    *aaaQueueReader: Jan 18 12:08:22.830: LOCAL_AUTH: (EAP:319) Sending the Rxd EAP packet (id 6) to EAP subsys
    *EAP Framework: Jan 18 12:08:22.831: EAP-EVENT: Received event 'EAP_RX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.831: EAP-AUTH-RX-PAK:
    *EAP Framework: Jan 18 12:08:22.831: eap_core.c:1484: Code:RESPONSE  ID:0x 6  Length:0x015c  Type:FAST
    *EAP Framework: Jan 18 12:08:22.831: eap_core.c:1422:     Payload:  810000015216030100070B0000030000 ...
    *EAP Framework: Jan 18 12:08:22.831: EAP-EVENT: Stopping 'Authenticator Retransmit' timer for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.831: EAP-AUTH-EVENT: EAP Response received by context 0x78000041
    *EAP Framework: Jan 18 12:08:22.832: EAP-AUTH-EVENT: EAP Response type = Method (43)
    *EAP Framework: Jan 18 12:08:22.832: EAP-AUTH-EVENT: Sending method data for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.832: EAP-EVENT: Sending method directive 'Receive Packet' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.832: eap_fast.c-AUTH-EVENT: Process Response, type: 0x2b
    *EAP Framework: Jan 18 12:08:22.832: eap_fast_auth.c-AUTH-EVENT: Process Response (EAP handle = 0x78000041)
    *EAP Framework: Jan 18 12:08:22.832: eap_fast_auth.c-RX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:22.832: eap_core.c:1484: Code:RESPONSE  ID:0x 6  Length:0x015c  Type:FAST
    *EAP Framework: Jan 18 12:08:22.832: eap_core.c:1422:     Payload:  810000015216030100070B0000030000 ...
    *EAP
    Framework: Jan 18 12:08:22.832: eap_fast_auth.c-AUTH-EVENT: Received
    TLS record type: Handshake in state: Sent provisioning Server Hello
    *EAP Framework: Jan 18 12:08:22.832: eap_fast_auth.c-AUTH-EVENT: Reading Client Certificate handshake
    *EAP Framework: Jan 18 12:08:22.832: eap_fast.c:286: EAP-FAST-AUTH-RX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.832: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x0007
    *EAP Framework: Jan 18 12:08:22.832: eap_core.c:1422:     Payload:  0B000003000000
    *EAP Framework: Jan 18 12:08:22.832: eap_fast.c:202: Handshake type:Certificate  Length:0x0003
    *EAP Framework: Jan 18 12:08:22.832: eap_core.c:1422:     Payload:  000000
    *EAP Framework: Jan 18 12:08:22.833: eap_fast.c-EVENT: Client Certificate handshake empty
    *EAP Framework: Jan 18 12:08:22.833: eap_fast_auth.c-AUTH-EVENT: Rx'd I-ID: "EAP-FAST I-ID" from Peer Cert
    *EAP Framework: Jan 18 12:08:22.833: eap_fast_auth.c-AUTH-ERROR: Required cert not provided by client
    *EAP Framework: Jan 18 12:08:22.833: eap_fast.c:286: EAP-FAST-AUTH-TX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.833: eap_fast.c:255: Content:Alert  Version:0301  Length:0x0002
    *EAP Framework: Jan 18 12:08:22.833: eap_core.c:1422:     Payload:  0228
    *EAP Framework: Jan 18 12:08:22.833: eap_fast_auth.c-AUTH-SM: Changing state: Sent provisioning Server Hello -> Alert
    *EAP Framework: Jan 18 12:08:22.833: eap_fast.c:2367: eap-fast tx packet:
    *EAP Framework: Jan 18 12:08:22.833: eap_fast.c:138: Version: 1  Flags:L  Length:0x0007
    *EAP Framework: Jan 18 12:08:22.833: eap_core.c:1422:     Payload:  15030100020228
    *EAP Framework: Jan 18 12:08:22.833: eap_fast.c-TX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:22.833: eap_core.c:1484: Code:REQUEST  ID:0x 0  Length:0x0011  Type:FAST
    *EAP Framework: Jan 18 12:08:22.833: eap_core.c:1422:     Payload:  810000000715030100020228
    *EAP Framework: Jan 18 12:08:22.833: EAP-AUTH-EVENT: EAP method state: Continue
    *EAP Framework: Jan 18 12:08:22.834: EAP-AUTH-EVENT: EAP method decision: Fail
    *EAP Framework: Jan 18 12:08:22.834: EAP-AUTH-EVENT: Current method = 43
    *EAP Framework: Jan 18 12:08:22.834: EAP-AUTH-EVENT: Sending packet to lower layer for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.834: EAP-AUTH-TX-PAK:
    *EAP Framework: Jan 18 12:08:22.834: eap_core.c:1484: Code:REQUEST  ID:0x 7  Length:0x0011  Type:FAST
    *EAP Framework: Jan 18 12:08:22.834: eap_core.c:1422:     Payload:  810000000715030100020228
    *EAP Framework: Jan 18 12:08:22.834: EAP-EVENT: Started 'Authenticator Retransmit' timer (60) for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.834: EAP-EVENT: Started EAP tick timer
    *EAP Framework: Jan 18 12:08:22.834: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.834: LOCAL_AUTH: Found matching context for id - 319
    *EAP Framework: Jan 18 12:08:22.834: LOCAL_AUTH: (EAP:319) transmit event
    *EAP Framework: Jan 18 12:08:22.834: AuthorizationResponse: 0x13c713fc
    We think that the reason why it didn´t work, is the part:
    *EAP Framework: Jan 18 12:08:22.833: eap_fast.c-EVENT: Client Certificate handshake empty
    *EAP Framework: Jan 18 12:08:22.833: eap_fast_auth.c-AUTH-EVENT: Rx'd I-ID: "EAP-FAST I-ID" from Peer Cert
    *EAP Framework: Jan 18 12:08:22.833: eap_fast_auth.c-AUTH-ERROR: Required cert not provided by client
    But we aren´t sure.
    Maybe anyone can help us. Many thanks in advance.
    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2012.01.18 12:08:18 =~=~=~=~=~=~=~=~=~=~=~=
    debug aaa all disable                     debug aaa all enable(Cisco Controller) >*Dot1x_NW_MsgTask_0: Jan 18 12:08:21.917: 18:3d:a2:0a:ec:bc Audit Session ID added to the mscb: 0a63081e000000994f16a825
    *Dot1x_NW_MsgTask_0: Jan 18 12:08:21.917: Creating audit session ID (dot1x_aaa_eapresp_supp) and Radius Request
    *aaaQueueReader: Jan 18 12:08:21.917: AuthenticationRequest: 0x30b52e90
    *aaaQueueReader: Jan 18 12:08:21.917: Callback.....................................0x10b7803c*aaaQueueReader: Jan 18 12:08:21.917: protocolType.................................0x00140001*aaaQueueReader: Jan 18 12:08:21.917: proxyState...................................18:3D:A2:0A:EC:BC-02:00*aaaQueueReader: Jan 18 12:08:21.917: Packet contains 16 AVPs (not shown)*aaaQueueReader: Jan 18 12:08:21.917: 18:3d:a2:0a:ec:bc [Error] Client requested no retries for mobile 18:3D:A2:0A:EC:BC
    *aaaQueueReader: Jan 18 12:08:21.918: 18:3d:a2:0a:ec:bc Returning AAA Error 'No Server' (-7) for mobile 18:3d:a2:0a:ec:bc
    *aaaQueueReader: Jan 18 12:08:21.918: AuthorizationResponse: 0x3e04bd08
    *aaaQueueReader: Jan 18 12:08:21.918: structureSize................................32*aaaQueueReader: Jan 18 12:08:21.918: resultCode...................................-7*aaaQueueReader: Jan 18 12:08:21.918: protocolUsed.................................0xffffffff*aaaQueueReader: Jan 18 12:08:21.918: proxyState...................................18:3D:A2:0A:EC:BC-02:00*aaaQueueReader: Jan 18 12:08:21.918: Packet contains 0 AVPs:*aaaQueueReader: Jan 18 12:08:21.918: LOCAL_AUTH: EAP: Received an auth request
    *aaaQueueReader: Jan 18 12:08:21.918: LOCAL_AUTH: Creating new context
    *aaaQueueReader: Jan 18 12:08:21.918: EAP-EVENT: Received context create from lower layer (0x0000013F)
    *aaaQueueReader: Jan 18 12:08:21.918: id_manager.c-AUTH-SM: Got new ID 78000041 - id_get
    *aaaQueueReader: Jan 18 12:08:21.918: EAP-EVENT: Received credential profile name: "(null)" from LL
    *aaaQueueReader: Jan 18 12:08:21.918: EAP-EVENT: Allocated new EAP context (handle = 0x78000041)
    *aaaQueueReader: Jan 18 12:08:21.919: LOCAL_AUTH: Created new context eap session handle 78000041
    *aaaQueueReader: Jan 18 12:08:21.919: LOCAL_AUTH: (EAP:319) Sending the Rxd EAP packet (id 1) to EAP subsys
    *EAP Framework: Jan 18 12:08:21.919: EAP-EVENT: Received event 'EAP_RX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:21.920: EAP-AUTH-RX-PAK:
    *EAP Framework: Jan 18 12:08:21.920: eap_core.c:1484: Code:RESPONSE  ID:0x 1  Length:0x002b  Type:IDENTITY
    *EAP Framework: Jan 18 12:08:21.920: eap_core.c:1422:     Payload:  416E6472652E54736368656E74736368 ...
    *EAP Framework: Jan 18 12:08:21.920: EAP-AUTH-EVENT: EAP Response received by context 0x78000041
    *EAP Framework: Jan 18 12:08:21.920: EAP-AUTH-EVENT: EAP Response type = Identity
    *EAP Framework: Jan 18 12:08:21.920: EAP-AUTH-EVENT: Received peer identity: [email protected]
    *EAP Framework: Jan 18 12:08:21.920: EAP-EVENT: Sending lower layer event 'EAP_GET_CREDENTIAL_PROFILE_FROM_USERNAME' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:21.920: LOCAL_AUTH: Found matching context for id - 319
    *EAP Framework: Jan 18 12:08:21.921: LOCAL_AUTH: (EAP) Sending user credential request username '[email protected]' to LDAP
    *aaaQueueReader: Jan 18 12:08:21.921: AuthenticationRequest: 0x33a6ae18
    *aaaQueueReader: Jan 18 12:08:21.921: Callback.....................................0x10765234*aaaQueueReader: Jan 18 12:08:21.921: protocolType.................................0x00100002*aaaQueueReader: Jan 18 12:08:21.921: proxyState...................................18:3D:A2:0A:EC:BC-00:00*aaaQueueReader: Jan 18 12:08:21.921: Packet contains 2 AVPs (not shown)*EAP Framework: Jan 18 12:08:21.921: EAP-AUTH-EVENT: Waiting for asynchronous reply from LL
    *LDAP DB Task 1: Jan 18 12:08:21.921: ldapTask [1] received msg 'REQUEST' (2) in state 'IDLE' (1)
    *LDAP DB Task 1: Jan 18 12:08:21.922: LDAP server 1 changed state to INIT
    *LDAP DB Task 1: Jan 18 12:08:21.922: LDAP_OPT_REFERRALS = -1*LDAP DB Task 1: Jan 18 12:08:21.922: ldapInitAndBind [1] called lcapi_init (rc = 0 - Success)
    *LDAP DB Task 1: Jan 18 12:08:21.925: ldapInitAndBind [1] configured Method Authenticated lcapi_bind (rc = 0 - Success)
    *LDAP DB Task 1: Jan 18 12:08:21.925: LDAP server 1 changed state to CONNECTED
    *LDAP DB Task 1: Jan 18 12:08:21.925: disabled LDAP_OPT_REFERRALS*LDAP DB Task 1: Jan 18 12:08:21.925: LDAP_CLIENT: UID Search (base=DC=group,DC=jenoptik,DC=corp, pattern=(&(objectclass=Person)([email protected])))
    *LDAP DB Task 1: Jan 18 12:08:21.926: LDAP_CLIENT: ldap_search_ext_s returns 0 85
    *LDAP DB Task 1: Jan 18 12:08:21.926: LDAP_CLIENT: Returned 2 msgs including 0 references
    *LDAP DB Task 1: Jan 18 12:08:21.926: LDAP_CLIENT: Returned msg 1 type 0x64
    *LDAP DB Task 1: Jan 18 12:08:21.926: LDAP_CLIENT: Received 1 attributes in search entry msg
    *LDAP DB Task 1: Jan 18 12:08:21.927: LDAP_CLIENT: Returned msg 2 type 0x65
    *LDAP DB Task 1: Jan 18 12:08:21.927: LDAP_CLIENT : No matched DN
    *LDAP DB Task 1: Jan 18 12:08:21.927: LDAP_CLIENT : Check result error 0 rc 1013
    *LDAP DB Task 1: Jan 18 12:08:21.927: LDAP_CLIENT: Received no referrals in search result msg
    *LDAP DB Task 1: Jan 18 12:08:21.927: ldapAuthRequest [1] called lcapi_query base="DC=group,DC=jenoptik,DC=corp" type="Person" attr="userPrincipalName" user="[email protected]" (rc = 0 - Success)
    *LDAP DB Task 1: Jan 18 12:08:21.927: LDAP ATTR> dn = CN=Tschentscher\, Andre,OU=Users,OU=SSC,OU=JOAG,DC=group,DC=jenoptik,DC=corp (size 76)
    *LDAP DB Task 1: Jan 18 12:08:21.927: Handling LDAP response Success
    *LDAP DB Task 1: Jan 18 12:08:21.927: 18:3d:a2:0a:ec:bc [Response] Client requested no retries for mobile 18:3D:A2:0A:EC:BC
    *LDAP DB Task 1: Jan 18 12:08:21.927: 18:3d:a2:0a:ec:bc Returning AAA Success for mobile 18:3d:a2:0a:ec:bc
    *LDAP DB Task 1: Jan 18 12:08:21.927: AuthorizationResponse: 0x33a5affc
    *LDAP DB Task 1: Jan 18 12:08:21.927: structureSize................................180*LDAP DB Task 1: Jan 18 12:08:21.927: resultCode...................................0*LDAP DB Task 1: Jan 18 12:08:21.927: protocolUsed.................................0x00000002*LDAP DB Task 1: Jan 18 12:08:21.927: proxyState...................................18:3D:A2:0A:EC:BC-00:00*LDAP DB Task 1: Jan 18 12:08:21.928: Packet contains 2 AVPs:*LDAP DB Task 1: Jan 18 12:08:21.928:     AVP[01] Unknown Attribute 0......................CN=Tschentscher\, Andre,OU=Users,OU=SSC,OU=JOAG,DC=group,DC=jenoptik,DC=corp (76 bytes)*LDAP DB Task 1: Jan 18 12:08:21.928:     AVP[02] User-Name................................Andre.Tschentscher@group.jenoptik.corp (38 bytes)*LDAP DB Task 1: Jan 18 12:08:21.928: LOCAL_AUTH: Found context matching MAC address - 319
    *LDAP DB Task 1: Jan 18 12:08:21.928: LOCAL_AUTH: (EAP:319) User credential callback invoked
    *LDAP DB Task 1: Jan 18 12:08:21.928: LOCAL_AUTH: EAP Unable to find password in credentials. Skipped
    *LDAP DB Task 1: Jan 18 12:08:21.928: LOCAL_AUTH: EAP Unable to find wlan in credentials. Skipped
    *LDAP DB Task 1: Jan 18 12:08:21.928: Authenticated bind : Closing the binded session*LDAP DB Task 1: Jan 18 12:08:21.928: ldapClose [1] called lcapi_close (rc = 0 - Success)
    *LDAP DB Task 1: Jan 18 12:08:21.929: LDAP server 1 changed state to IDLE
    *EAP Framework: Jan 18 12:08:21.930: EAP-EVENT: Received event 'EAP_LL_REPLY' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:21.930: EAP-AUTH-EVENT: Using credential profile name: [email protected] (0x78000041)
    *EAP Framework: Jan 18 12:08:21.930: EAP-AUTH-EVENT: Maximum EAP packet size: 1000
    *EAP Framework: Jan 18 12:08:21.930: EAP-AUTH-EVENT: Sending method new context directive for EAP context 0x78000041
    *EAP Framework: Jan 18 12:08:21.930: EAP-EVENT: Sending method directive 'New Context' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:21.930: eap_fast.c-EVENT: New context (EAP handle = 0x78000041)
    *EAP Framework: Jan 18 12:08:21.931: id_manager.c-AUTH-SM: Got new ID f700000e - id_get
    *EAP Framework: Jan 18 12:08:21.931: eap_fast.c-EVENT: Allocated new EAP-FAST context (handle = 0xF700000E)
    *EAP Framework: Jan 18 12:08:21.931: EAP-AUTH-EVENT: Sending method data for context 0x78000041
    *EAP Framework: Jan 18 12:08:21.931: EAP-EVENT: Sending method directive 'Receive Packet' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:21.931: eap_fast_auth.c-AUTH-EVENT: Process Response (EAP handle = 0x78000041)
    *EAP Framework: Jan 18 12:08:21.931: eap_fast_auth.c-AUTH-EVENT: Received Identity
    *EAP Framework: Jan 18 12:08:21.931: eap_fast_tlv.c-AUTH-EVENT: Adding PAC A-ID TLV (436973636f0000000000000000000000)
    *EAP Framework: Jan 18 12:08:21.931: eap_fast_auth.c-AUTH-EVENT: Sending Start
    *EAP Framework: Jan 18 12:08:21.931: eap_fast_auth.c-AUTH-SM: Changing state: Reset -> Start
    *EAP Framework: Jan 18 12:08:21.931: eap_fast.c:2367: eap-fast tx packet:
    *EAP Framework: Jan 18 12:08:21.931: eap_fast.c:138: Version: 1  Flags:S  Length:0x0014
    *EAP Framework: Jan 18 12:08:21.931: eap_core.c:1422:     Payload:  00040010436973636F00000000000000 ...
    *EAP Framework: Jan 18 12:08:21.931: eap_fast.c-TX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:21.931: eap_core.c:1484: Code:REQUEST  ID:0x 0  Length:0x001a  Type:FAST
    *EAP Framework: Jan 18 12:08:21.932: eap_core.c:1422:     Payload:  2100040010436973636F000000000000 ...
    *EAP Framework: Jan 18 12:08:21.932: EAP-AUTH-EVENT: EAP method state: Continue
    *EAP Framework: Jan 18 12:08:21.932: EAP-AUTH-EVENT: EAP method decision: Unknown
    *EAP Framework: Jan 18 12:08:21.932: EAP-AUTH-EVENT: Current method = 43
    *EAP Framework: Jan 18 12:08:21.932: EAP-AUTH-EVENT: Sending packet to lower layer for context 0x78000041
    *EAP Framework: Jan 18 12:08:21.932: EAP-AUTH-TX-PAK:
    *EAP Framework: Jan 18 12:08:21.932: eap_core.c:1484: Code:REQUEST  ID:0x 2  Length:0x001a  Type:FAST
    *EAP Framework: Jan 18 12:08:21.932: eap_core.c:1422:     Payload:  2100040010436973636F000000000000 ...
    *EAP Framework: Jan 18 12:08:21.932: EAP-EVENT: Started 'Authenticator Retransmit' timer (60) for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:21.932: EAP-EVENT: Started EAP tick timer
    *EAP Framework: Jan 18 12:08:21.932: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:21.932: LOCAL_AUTH: Found matching context for id - 319
    *EAP Framework: Jan 18 12:08:21.932: LOCAL_AUTH: (EAP:319) transmit event
    *EAP Framework: Jan 18 12:08:21.932: AuthorizationResponse: 0x13c713fc
    *EAP Framework: Jan 18 12:08:21.933: structureSize................................74*EAP Framework: Jan 18 12:08:21.933: resultCode...................................255*EAP Framework: Jan 18 12:08:21.933: protocolUsed.................................0x00000080*EAP Framework: Jan 18 12:08:21.933: proxyState...................................18:3D:A2:0A:EC:BC-02:00*EAP Framework: Jan 18 12:08:21.934: Packet contains 1 AVPs (not shown)*EAP Framework: Jan 18 12:08:21.934: LOCAL_AUTH: AAA LOCAL AUTH EAP PKT AVP attribute 4f length 1a
    *EAP Framework: Jan 18 12:08:21.934: LOCAL_AUTH: AAA LOCAL AUTH TX PKT DUMP code cc id 00 type 2b
    *aaaQueueReader: Jan 18 12:08:22.290: LOCAL_AUTH: EAP: Received an auth request
    *aaaQueueReader: Jan 18 12:08:22.290: LOCAL_AUTH: Found context matching MAC address - 319
    *aaaQueueReader: Jan 18 12:08:22.290: LOCAL_AUTH: (EAP:319) Sending the Rxd EAP packet (id 2) to EAP subsys
    *EAP Framework: Jan 18 12:08:22.291: EAP-EVENT: Received event 'EAP_RX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.291: EAP-AUTH-RX-PAK:
    *EAP Framework: Jan 18 12:08:22.291: eap_core.c:1484: Code:RESPONSE  ID:0x 2  Length:0x0042  Type:FAST
    *EAP Framework: Jan 18 12:08:22.291: eap_core.c:1422:     Payload:  810000003816030100330100002F0301 ...
    *EAP Framework: Jan 18 12:08:22.291: EAP-EVENT: Stopping 'Authenticator Retransmit' timer for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.291: EAP-AUTH-EVENT: EAP Response received by context 0x78000041
    *EAP Framework: Jan 18 12:08:22.291: EAP-AUTH-EVENT: EAP Response type = Method (43)
    *EAP Framework: Jan 18 12:08:22.291: EAP-AUTH-EVENT: Sending method data for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.292: EAP-EVENT: Sending method directive 'Receive Packet' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.292: eap_fast.c-AUTH-EVENT: Process Response, type: 0x2b
    *EAP Framework: Jan 18 12:08:22.292: eap_fast_auth.c-AUTH-EVENT: Process Response (EAP handle = 0x78000041)
    *EAP Framework: Jan 18 12:08:22.292: eap_fast_auth.c-RX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:22.292: eap_core.c:1484: Code:RESPONSE  ID:0x 2  Length:0x0042  Type:FAST
    *EAP Framework: Jan 18 12:08:22.292: eap_core.c:1422:     Payload:  810000003816030100330100002F0301 ...
    *EAP Framework: Jan 18 12:08:22.292: eap_fast_auth.c-AUTH-EVENT: Received TLS record type: Handshake in state: Start
    *EAP Framework: Jan 18 12:08:22.292: EAP-EVENT: Sending lower layer event 'EAP_GET_CREDENTIAL_PROFILE_FROM_PROFILE_NAME' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.292: LOCAL_AUTH: Found matching context for id - 319
    *EAP Framework: Jan 18 12:08:22.292: LOCAL_AUTH: (EAP:319) Returning profile '[email protected]' (username '[email protected]')
    *EAP Framework: Jan 18 12:08:22.293: IOS_PKI_SHIM: [StartSession] - New session 0x335ee108 started (TP = 'vendor')
    *EAP Framework: Jan 18 12:08:22.293: IOS_PKI_SHIM: [StartSession] - Trustpoint identity (cert) set to 'Vendor'
    *EAP Framework: Jan 18 12:08:22.297: IOS_PKI_SHIM: [ID-CERT] Subject : C=DE, ST=Thuringia, L=Jena, O=Jenoptik AG, OU=Jenoptik SSC GmbH, CN=Cisco WLC 1st, [email protected]
    *EAP Framework: Jan 18 12:08:22.297: IOS_PKI_SHIM: [ID-CERT] Issuer : DC=corp, DC=jenoptik, CN=Jenoptik WLAN Certificate Authority
    *EAP Framework: Jan 18 12:08:22.297: IOS_PKI_SHIM: [ID-CERT] Valid from '2012 Jan 12th, 17:06:50 GMT' to '2016 Jan 11th, 17:06:50 GMT'
    *EAP Framework: Jan 18 12:08:22.297: IOS_PKI_SHIM: [ID-CERT] Is not a CA cert
    *EAP Framework: Jan 18 12:08:22.297: IOS_PKI_SHIM: Added cert (type 1) to chain (1 present on chain)
    *EAP Framework: Jan 18 12:08:22.300: IOS_PKI_SHIM: [CA-CERT] Subject : DC=corp, DC=jenoptik, CN=Jenoptik WLAN Certificate Authority
    *EAP Framework: Jan 18 12:08:22.301: IOS_PKI_SHIM: [CA-CERT] Issuer : CN=Jenoptik Certificate Authority
    *EAP Framework: Jan 18 12:08:22.301: IOS_PKI_SHIM: [CA-CERT] Valid from '2012 Jan 12th, 16:54:49 GMT' to '2020 Jan 12th, 17:04:49 GMT'
    *EAP Framework: Jan 18 12:08:22.301: IOS_PKI_SHIM: [CA-CERT] Is a CA cert
    *EAP Framework: Jan 18 12:08:22.301: IOS_PKI_SHIM: Added cert (type 2) to chain (2 present on chain)
    *EAP Framework: Jan 18 12:08:22.301: IOS_PKI_SHIM: [StartSession] - Getting older style priv key
    *EAP Framework: Jan 18 12:08:22.338: IOS_PKI_SHIM: Session 0x335ee108 init'd OK
    *EAP Framework: Jan 18 12:08:22.338: eap_fast_auth.c-AUTH-EVENT: Local certificate found
    *EAP Framework: Jan 18 12:08:22.339: eap_fast_auth.c-AUTH-EVENT: Reading Client Hello handshake
    *EAP Framework: Jan 18 12:08:22.339: eap_fast.c:286: EAP-FAST-AUTH-RX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.339: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x0033
    *EAP Framework: Jan 18 12:08:22.339: eap_core.c:1422:     Payload:  0100002F03014F16A8262631FC9DC042 ...
    *EAP Framework: Jan 18 12:08:22.340: eap_fast.c:202: Handshake type:Client Hello  Length:0x002F
    *EAP Framework: Jan 18 12:08:22.340: eap_core.c:1422:     Payload:  03014F16A8262631FC9DC042253D3E24 ...
    *EAP Framework: Jan 18 12:08:22.340: eap_fast_auth.c-AUTH-EVENT: TLS_RSA_WITH_AES_128 proposed...
    *EAP Framework: Jan 18 12:08:22.341: eap_fast_auth.c-AUTH-EVENT: TLS_DHE_RSA_WITH_AES_128_CBC_SHA proposed...
    *EAP Framework: Jan 18 12:08:22.341: eap_fast_auth.c-AUTH-EVENT: TLS_RSA_WITH_RC4_128 proposed...
    *EAP Framework: Jan 18 12:08:22.341: eap_fast_auth.c-AUTH-EVENT: TLS_DH_anon_WITH_AES_128_CBC_SHA proposed...
    *EAP Framework: Jan 18 12:08:22.342: eap_fast.c-EVENT: Proposed ciphersuite(s):
    *EAP Framework: Jan 18 12:08:22.342: eap_fast.c-EVENT:     TLS_RSA_WITH_AES_128_CBC_SHA
    *EAP Framework: Jan 18 12:08:22.342: eap_fast.c-EVENT:     TLS_DHE_RSA_WITH_AES_128_CBC_SHA
    *EAP Framework: Jan 18 12:08:22.342: eap_fast.c-EVENT:     TLS_RSA_WITH_RC4_128_SHA
    *EAP Framework: Jan 18 12:08:22.343: eap_fast.c-EVENT:     TLS_DH_anon_WITH_AES_128_CBC_SHA
    *EAP Framework: Jan 18 12:08:22.343: eap_fast.c-EVENT: Selected ciphersuite:
    *EAP Framework: Jan 18 12:08:22.343: eap_fast.c-EVENT:     TLS_DHE_RSA_WITH_AES_128_CBC_SHA
    *EAP Framework: Jan 18 12:08:22.343: eap_fast_auth.c-AUTH-EVENT: Building Provisioning Server Hello
    *EAP Framework: Jan 18 12:08:22.344: eap_fast.c:286: EAP-FAST-AUTH-TX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.344: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x002A
    *EAP Framework: Jan 18 12:08:22.344: eap_core.c:1422:     Payload:  0200002603015F3325EADF12E6296F91 ...
    *EAP Framework: Jan 18 12:08:22.344: eap_fast.c:202: Handshake type:Server Hello  Length:0x0026
    *EAP Framework: Jan 18 12:08:22.345: eap_core.c:1422:     Payload:  03015F3325EADF12E6296F91530FE67F ...
    *EAP Framework: Jan 18 12:08:22.345: eap_fast.c:286: EAP-FAST-AUTH-TX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.345: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x0B54
    *EAP Framework: Jan 18 12:08:22.346: eap_core.c:1422:     Payload:  0B000B50000B4D00059F3082059B3082 ...
    *EAP Framework: Jan 18 12:08:22.346: eap_fast.c:202: Handshake type:Certificate  Length:0x0B50
    *EAP Framework: Jan 18 12:08:22.346: eap_core.c:1422:     Payload:  000B4D00059F3082059B30820483A003 ...
    *EAP Framework: Jan 18 12:08:22.347: eap_fast_crypto.c-EVENT: Starting Diffie Hellman phase 1 ...
    *EAP Framework: Jan 18 12:08:22.661: eap_fast_crypto.c-EVENT: Diffie Hellman phase 1 complete
    *EAP Framework: Jan 18 12:08:22.677: IOS_PKI_SHIM: PKI_SignMessage PostHashEncrypt ret SUCCESS.. op_len 128
    *EAP Framework: Jan 18 12:08:22.678: eap_fast_auth.c-AUTH-EVENT: DH signature length = 128
    *EAP Framework: Jan 18 12:08:22.678: eap_fast.c:286: EAP-FAST-AUTH-TX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.678: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x028D
    *EAP Framework: Jan 18 12:08:22.679: eap_core.c:1422:     Payload:  0C0002890100FFFFFFFFFFFFFFFFC90F ...
    *EAP Framework: Jan 18 12:08:22.679: eap_fast.c:202: Handshake type:Server Key Exchange  Length:0x0289
    *EAP Framework: Jan 18 12:08:22.679: eap_core.c:1422:     Payload:  0100FFFFFFFFFFFFFFFFC90FDAA22168 ...
    *EAP Framework: Jan 18 12:08:22.679: eap_fast.c:286: EAP-FAST-AUTH-TX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.680: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x000B
    *EAP Framework: Jan 18 12:08:22.680: eap_core.c:1422:     Payload:  0D00000704030401020000
    *EAP Framework: Jan 18 12:08:22.680: eap_fast.c:202: Handshake type:Certificate Request  Length:0x0007
    *EAP Framework: Jan 18 12:08:22.680: eap_core.c:1422:     Payload:  04030401020000
    *EAP Framework: Jan 18 12:08:22.681: eap_fast.c:286: EAP-FAST-AUTH-TX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.681: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x0004
    *EAP Framework: Jan 18 12:08:22.681: eap_core.c:1422:     Payload:  0E000000
    *EAP Framework: Jan 18 12:08:22.681: eap_fast.c:202: Handshake type:Server Done  Length:0x0000
    *EAP Framework: Jan 18 12:08:22.682: eap_fast_auth.c-AUTH-EVENT: Sending Provisioning Serving Hello
    *EAP Framework: Jan 18 12:08:22.682: eap_fast_auth.c-AUTH-SM: Changing state: Start -> Sent provisioning Server Hello
    *EAP Framework: Jan 18 12:08:22.682: eap_fast.c-EVENT: Tx packet fragmentation required
    *EAP Framework: Jan 18 12:08:22.683: eap_fast.c:2367: eap-fast tx packet:
    *EAP Framework: Jan 18 12:08:22.683: eap_fast.c:138: Version: 1  Flags:LM  Length:0x03DE
    *EAP Framework: Jan 18 12:08:22.683: eap_core.c:1422:     Payload:  160301002A0200002603015F3325EADF ...
    *EAP Framework: Jan 18 12:08:22.684: eap_fast.c-TX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:22.684: eap_core.c:1484: Code:REQUEST  ID:0x 0  Length:0x03e8  Type:FAST
    *EAP Framework: Jan 18 12:08:22.684: eap_core.c:1422:     Payload:  C100000E33160301002A020000260301 ...
    *EAP Framework: Jan 18 12:08:22.684: EAP-AUTH-EVENT: EAP method state: Continue
    *EAP Framework: Jan 18 12:08:22.685: EAP-AUTH-EVENT: EAP method decision: Unknown
    *EAP Framework: Jan 18 12:08:22.685: EAP-AUTH-EVENT: Current method = 43
    *EAP Framework: Jan 18 12:08:22.685: EAP-AUTH-EVENT: Sending packet to lower layer for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.685: EAP-AUTH-TX-PAK:
    *EAP Framework: Jan 18 12:08:22.685: eap_core.c:1484: Code:REQUEST  ID:0x 3  Length:0x03e8  Type:FAST
    *EAP Framework: Jan 18 12:08:22.686: eap_core.c:1422:     Payload:  C100000E33160301002A020000260301 ...
    *EAP Framework: Jan 18 12:08:22.686: EAP-EVENT: Started 'Authenticator Retransmit' timer (60) for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.686: EAP-EVENT: Started EAP tick timer
    *EAP Framework: Jan 18 12:08:22.686: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.686: LOCAL_AUTH: Found matching context for id - 319
    *EAP Framework: Jan 18 12:08:22.687: LOCAL_AUTH: (EAP:319) transmit event
    *EAP Framework: Jan 18 12:08:22.687: AuthorizationResponse: 0x13c713fc
    *EAP Framework: Jan 18 12:08:22.687: structureSize................................1048*EAP Framework: Jan 18 12:08:22.687: resultCode...................................255*EAP Framework: Jan 18 12:08:22.687: protocolUsed.................................0x00000080*EAP Framework: Jan 18 12:08:22.688: proxyState...................................18:3D:A2:0A:EC:BC-02:01*EAP Framework: Jan 18 12:08:22.688: Packet contains 1 AVPs (not shown)*EAP Framework: Jan 18 12:08:22.688: LOCAL_AUTH: AAA LOCAL AUTH EAP PKT AVP attribute 4f length 3e8
    *EAP Framework: Jan 18 12:08:22.688: LOCAL_AUTH: AAA LOCAL AUTH TX PKT DUMP code cc id 00 type 2b
    *aaaQueueReader: Jan 18 12:08:22.700: LOCAL_AUTH: EAP: Received an auth request
    *aaaQueueReader: Jan 18 12:08:22.701: LOCAL_AUTH: Found context matching MAC address - 319
    *aaaQueueReader: Jan 18 12:08:22.701: LOCAL_AUTH: (EAP:319) Sending the Rxd EAP packet (id 3) to EAP subsys
    *EAP Framework: Jan 18 12:08:22.701: EAP-EVENT: Received event 'EAP_RX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.701: EAP-AUTH-RX-PAK:
    *EAP Framework: Jan 18 12:08:22.702: eap_core.c:1484: Code:RESPONSE  ID:0x 3  Length:0x0006  Type:FAST
    *EAP Framework: Jan 18 12:08:22.702: eap_core.c:1422:     Payload:  01
    *EAP Framework: Jan 18 12:08:22.702: EAP-EVENT: Stopping 'Authenticator Retransmit' timer for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.703: EAP-AUTH-EVENT: EAP Response received by context 0x78000041
    *EAP Framework: Jan 18 12:08:22.703: EAP-AUTH-EVENT: EAP Response type = Method (43)
    *EAP Framework: Jan 18 12:08:22.703: EAP-AUTH-EVENT: Sending method data for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.704: EAP-EVENT: Sending method directive 'Receive Packet' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.704: eap_fast.c-AUTH-EVENT: eap_fast_rx_packet(): EAP Fast NoData (0x2b)
    *EAP Framework: Jan 18 12:08:22.704: eap_fast.c:2367: eap-fast tx packet:
    *EAP Framework: Jan 18 12:08:22.704: eap_fast.c:138: Version: 1  Flags:M  Length:0x03E2
    *EAP Framework: Jan 18 12:08:22.705: eap_core.c:1422:     Payload:  3A2F2F2F434E3D4A656E6F7074696B25 ...
    *EAP Framework: Jan 18 12:08:22.705: eap_fast.c-TX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:22.705: eap_core.c:1484: Code:REQUEST  ID:0x 0  Length:0x03e8  Type:FAST
    *EAP Framework: Jan 18 12:08:22.705: eap_core.c:1422:     Payload:  413A2F2F2F434E3D4A656E6F7074696B ...
    *EAP Framework: Jan 18 12:08:22.706: EAP-AUTH-EVENT: EAP method state: Continue
    *EAP Framework: Jan 18 12:08:22.706: EAP-AUTH-EVENT: EAP method decision: Unknown
    *EAP Framework: Jan 18 12:08:22.706: EAP-AUTH-EVENT: Current method = 43
    *EAP Framework: Jan 18 12:08:22.706: EAP-AUTH-EVENT: Sending packet to lower layer for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.707: EAP-AUTH-TX-PAK:
    *EAP Framework: Jan 18 12:08:22.707: eap_core.c:1484: Code:REQUEST  ID:0x 4  Length:0x03e8  Type:FAST
    *EAP Framework: Jan 18 12:08:22.707: eap_core.c:1422:     Payload:  413A2F2F2F434E3D4A656E6F7074696B ...
    *EAP Framework: Jan 18 12:08:22.707: EAP-EVENT: Started 'Authenticator Retransmit' timer (60) for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.708: EAP-EVENT: Started EAP tick timer
    *EAP Framework: Jan 18 12:08:22.708: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.708: LOCAL_AUTH: Found matching context for id - 319
    *EAP Framework: Jan 18 12:08:22.708: LOCAL_AUTH: (EAP:319) transmit event
    *EAP Framework: Jan 18 12:08:22.709: AuthorizationResponse: 0x13c713fc
    *EAP Framework: Jan 18 12:08:22.709: structureSize................................1048*EAP Framework: Jan 18 12:08:22.709: resultCode...................................255*EAP Framework: Jan 18 12:08:22.709: protocolUsed.................................0x00000080*EAP Framework: Jan 18 12:08:22.710: proxyState...................................18:3D:A2:0A:EC:BC-02:02*EAP Framework: Jan 18 12:08:22.710: Packet contains 1 AVPs (not shown)*EAP Framework: Jan 18 12:08:22.710: LOCAL_AUTH: AAA LOCAL AUTH EAP PKT AVP attribute 4f length 3e8
    *EAP Framework: Jan 18 12:08:22.711: LOCAL_AUTH: AAA LOCAL AUTH TX PKT DUMP code cc id 00 type 2b
    *aaaQueueReader: Jan 18 12:08:22.723: LOCAL_AUTH: EAP: Received an auth request
    *aaaQueueReader: Jan 18 12:08:22.723: LOCAL_AUTH: Found context matching MAC address - 319
    *aaaQueueReader: Jan 18 12:08:22.724: LOCAL_AUTH: (EAP:319) Sending the Rxd EAP packet (id 4) to EAP subsys
    *EAP Framework: Jan 18 12:08:22.724: EAP-EVENT: Received event 'EAP_RX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.725: EAP-AUTH-RX-PAK:
    *EAP Framework: Jan 18 12:08:22.725: eap_core.c:1484: Code:RESPONSE  ID:0x 4  Length:0x0006  Type:FAST
    *EAP Framework: Jan 18 12:08:22.725: eap_core.c:1422:     Payload:  01
    *EAP Framework: Jan 18 12:08:22.725: EAP-EVENT: Stopping 'Authenticator Retransmit' timer for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.726: EAP-AUTH-EVENT: EAP Response received by context 0x78000041
    *EAP Framework: Jan 18 12:08:22.726: EAP-AUTH-EVENT: EAP Response type = Method (43)
    *EAP Framework: Jan 18 12:08:22.726: EAP-AUTH-EVENT: Sending method data for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.726: EAP-EVENT: Sending method directive 'Receive Packet' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.727: eap_fast.c-AUTH-EVENT: eap_fast_rx_packet(): EAP Fast NoData (0x2b)
    *EAP Framework: Jan 18 12:08:22.727: eap_fast.c:2367: eap-fast tx packet:
    *EAP Framework: Jan 18 12:08:22.727: eap_fast.c:138: Version: 1  Flags:M  Length:0x03E2
    *EAP Framework: Jan 18 12:08:22.728: eap_core.c:1422:     Payload:  BD84CC4BF49A766267DA94429BEBE087 ...
    *EAP Framework: Jan 18 12:08:22.728: eap_fast.c-TX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:22.728: eap_core.c:1484: Code:REQUEST  ID:0x 0  Length:0x03e8  Type:FAST
    *EAP Framework: Jan 18 12:08:22.728: eap_core.c:1422:     Payload:  41BD84CC4BF49A766267DA94429BEBE0 ...
    *EAP Framework: Jan 18 12:08:22.729: EAP-AUTH-EVENT: EAP method state: Continue
    *EAP Framework: Jan 18 12:08:22.729: EAP-AUTH-EVENT: EAP method decision: Unknown
    *EAP Framework: Jan 18 12:08:22.729: EAP-AUTH-EVENT: Current method = 43
    *EAP Framework: Jan 18 12:08:22.729: EAP-AUTH-EVENT: Sending packet to lower layer for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.730: EAP-AUTH-TX-PAK:
    *EAP Framework: Jan 18 12:08:22.730: eap_core.c:1484: Code:REQUEST  ID:0x 5  Length:0x03e8  Type:FAST
    *EAP Framework: Jan 18 12:08:22.730: eap_core.c:1422:     Payload:  41BD84CC4BF49A766267DA94429BEBE0 ...
    *EAP Framework: Jan 18 12:08:22.731: EAP-EVENT: Started 'Authenticator Retransmit' timer (60) for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.731: EAP-EVENT: Started EAP tick timer
    *EAP Framework: Jan 18 12:08:22.731: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.731: LOCAL_AUTH: Found matching context for id - 319
    *EAP Framework: Jan 18 12:08:22.732: LOCAL_AUTH: (EAP:319) transmit event
    *EAP Framework: Jan 18 12:08:22.732: AuthorizationResponse: 0x13c713fc
    *EAP Framework: Jan 18 12:08:22.732: structureSize................................1048*EAP Framework: Jan 18 12:08:22.732: resultCode...................................255*EAP Framework: Jan 18 12:08:22.733: protocolUsed.................................0x00000080*EAP Framework: Jan 18 12:08:22.733: proxyState...................................18:3D:A2:0A:EC:BC-02:03*EAP Framework: Jan 18 12:08:22.733: Packet contains 1 AVPs (not shown)*EAP Framework: Jan 18 12:08:22.734: LOCAL_AUTH: AAA LOCAL AUTH EAP PKT AVP attribute 4f length 3e8
    *EAP Framework: Jan 18 12:08:22.734: LOCAL_AUTH: AAA LOCAL AUTH TX PKT DUMP code cc id 00 type 2b
    *aaaQueueReader: Jan 18 12:08:22.746: LOCAL_AUTH: EAP: Received an auth request
    *aaaQueueReader: Jan 18 12:08:22.747: LOCAL_AUTH: Found context matching MAC address - 319
    *aaaQueueReader: Jan 18 12:08:22.747: LOCAL_AUTH: (EAP:319) Sending the Rxd EAP packet (id 5) to EAP subsys
    *EAP Framework: Jan 18 12:08:22.747: EAP-EVENT: Received event 'EAP_RX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.747: EAP-AUTH-RX-PAK:
    *EAP Framework: Jan 18 12:08:22.748: eap_core.c:1484: Code:RESPONSE  ID:0x 5  Length:0x0006  Type:FAST
    *EAP Framework: Jan 18 12:08:22.748: eap_core.c:1422:     Payload:  01
    *EAP Framework: Jan 18 12:08:22.748: EAP-EVENT: Stopping 'Authenticator Retransmit' timer for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.749: EAP-AUTH-EVENT: EAP Response received by context 0x78000041
    *EAP Framework: Jan 18 12:08:22.749: EAP-AUTH-EVENT: EAP Response type = Method (43)
    *EAP Framework: Jan 18 12:08:22.749: EAP-AUTH-EVENT: Sending method data for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.750: EAP-EVENT: Sending method directive 'Receive Packet' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.750: eap_fast.c-AUTH-EVENT: eap_fast_rx_packet(): EAP Fast NoData (0x2b)
    *EAP Framework: Jan 18 12:08:22.750: eap_fast.c:2367: eap-fast tx packet:
    *EAP Framework: Jan 18 12:08:22.750: eap_fast.c:138: Version: 1  Flags:  Length:0x0291
    *EAP Framework: Jan 18 12:08:22.751: eap_core.c:1422:     Payload:  34C4C6628B80DC1CD129024E088A67CC ...
    *EAP Framework: Jan 18 12:08:22.751: eap_fast.c-TX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:22.751: eap_core.c:1484: Code:REQUEST  ID:0x 0  Length:0x0297  Type:FAST
    *EAP Framework: Jan 18 12:08:22.751: eap_core.c:1422:     Payload:  0134C4C6628B80DC1CD129024E088A67 ...
    *EAP Framework: Jan 18 12:08:22.751: EAP-AUTH-EVENT: EAP method state: Continue
    *EAP Framework: Jan 18 12:08:22.751: EAP-AUTH-EVENT: EAP method decision: Unknown
    *EAP Framework: Jan 18 12:08:22.752: EAP-AUTH-EVENT: Current method = 43
    *EAP Framework: Jan 18 12:08:22.752: EAP-AUTH-EVENT: Sending packet to lower layer for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.752: EAP-AUTH-TX-PAK:
    *EAP Framework: Jan 18 12:08:22.752: eap_core.c:1484: Code:REQUEST  ID:0x 6  Length:0x0297  Type:FAST
    *EAP Framework: Jan 18 12:08:22.752: eap_core.c:1422:     Payload:  0134C4C6628B80DC1CD129024E088A67 ...
    *EAP Framework: Jan 18 12:08:22.753: EAP-EVENT: Started 'Authenticator Retransmit' timer (60) for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.753: EAP-EVENT: Started EAP tick timer
    *EAP Framework: Jan 18 12:08:22.753: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.753: LOCAL_AUTH: Found matching context for id - 319
    *EAP Framework: Jan 18 12:08:22.753: LOCAL_AUTH: (EAP:319) transmit event
    *EAP Framework: Jan 18 12:08:22.754: AuthorizationResponse: 0x13c713fc
    *EAP Framework: Jan 18 12:08:22.754: structureSize................................711*EAP Framework: Jan 18 12:08:22.754: resultCode...................................255*EAP Framework: Jan 18 12:08:22.754: protocolUsed.................................0x00000080*EAP Framework: Jan 18 12:08:22.754: proxyState...................................18:3D:A2:0A:EC:BC-02:04*EAP Framework: Jan 18 12:08:22.754: Packet contains 1 AVPs (not shown)*EAP Framework: Jan 18 12:08:22.755: LOCAL_AUTH: AAA LOCAL AUTH EAP PKT AVP attribute 4f length 297
    *EAP Framework: Jan 18 12:08:22.755: LOCAL_AUTH: AAA LOCAL AUTH TX PKT DUMP code cc id 00 type 2b
    *aaaQueueReader: Jan 18 12:08:22.830: LOCAL_AUTH: EAP: Received an auth request
    *aaaQueueReader: Jan 18 12:08:22.830: LOCAL_AUTH: Found context matching MAC address - 319
    *aaaQueueReader: Jan 18 12:08:22.830: LOCAL_AUTH: (EAP:319) Sending the Rxd EAP packet (id 6) to EAP subsys
    *EAP Framework: Jan 18 12:08:22.831: EAP-EVENT: Received event 'EAP_RX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.831: EAP-AUTH-RX-PAK:
    *EAP Framework: Jan 18 12:08:22.831: eap_core.c:1484: Code:RESPONSE  ID:0x 6  Length:0x015c  Type:FAST
    *EAP Framework: Jan 18 12:08:22.831: eap_core.c:1422:     Payload:  810000015216030100070B0000030000 ...
    *EAP Framework: Jan 18 12:08:22.831: EAP-EVENT: Stopping 'Authenticator Retransmit' timer for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.831: EAP-AUTH-EVENT: EAP Response received by context 0x78000041
    *EAP Framework: Jan 18 12:08:22.832: EAP-AUTH-EVENT: EAP Response type = Method (43)
    *EAP Framework: Jan 18 12:08:22.832: EAP-AUTH-EVENT: Sending method data for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.832: EAP-EVENT: Sending method directive 'Receive Packet' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.832: eap_fast.c-AUTH-EVENT: Process Response, type: 0x2b
    *EAP Framework: Jan 18 12:08:22.832: eap_fast_auth.c-AUTH-EVENT: Process Response (EAP handle = 0x78000041)
    *EAP Framework: Jan 18 12:08:22.832: eap_fast_auth.c-RX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:22.832: eap_core.c:1484: Code:RESPONSE  ID:0x 6  Length:0x015c  Type:FAST
    *EAP Framework: Jan 18 12:08:22.832: eap_core.c:1422:     Payload:  810000015216030100070B0000030000 ...
    *EAP Framework: Jan 18 12:08:22.832: eap_fast_auth.c-AUTH-EVENT: Received TLS record type: Handshake in state: Sent provisioning Server Hello
    *EAP Framework: Jan 18 12:08:22.832: eap_fast_auth.c-AUTH-EVENT: Reading Client Certificate handshake
    *EAP Framework: Jan 18 12:08:22.832: eap_fast.c:286: EAP-FAST-AUTH-RX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.832: eap_fast.c:255: Content:Handshake  Version:0301  Length:0x0007
    *EAP Framework: Jan 18 12:08:22.832: eap_core.c:1422:     Payload:  0B000003000000
    *EAP Framework: Jan 18 12:08:22.832: eap_fast.c:202: Handshake type:Certificate  Length:0x0003
    *EAP Framework: Jan 18 12:08:22.832: eap_core.c:1422:     Payload:  000000
    *EAP Framework: Jan 18 12:08:22.833: eap_fast.c-EVENT: Client Certificate handshake empty
    *EAP Framework: Jan 18 12:08:22.833: eap_fast_auth.c-AUTH-EVENT: Rx'd I-ID: "EAP-FAST I-ID" from Peer Cert
    *EAP Framework: Jan 18 12:08:22.833: eap_fast_auth.c-AUTH-ERROR: Required cert not provided by client
    *EAP Framework: Jan 18 12:08:22.833: eap_fast.c:286: EAP-FAST-AUTH-TX-TLS-RECORD:
    *EAP Framework: Jan 18 12:08:22.833: eap_fast.c:255: Content:Alert  Version:0301  Length:0x0002
    *EAP Framework: Jan 18 12:08:22.833: eap_core.c:1422:     Payload:  0228
    *EAP Framework: Jan 18 12:08:22.833: eap_fast_auth.c-AUTH-SM: Changing state: Sent provisioning Server Hello -> Alert
    *EAP Framework: Jan 18 12:08:22.833: eap_fast.c:2367: eap-fast tx packet:
    *EAP Framework: Jan 18 12:08:22.833: eap_fast.c:138: Version: 1  Flags:L  Length:0x0007
    *EAP Framework: Jan 18 12:08:22.833: eap_core.c:1422:     Payload:  15030100020228
    *EAP Framework: Jan 18 12:08:22.833: eap_fast.c-TX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:22.833: eap_core.c:1484: Code:REQUEST  ID:0x 0  Length:0x0011  Type:FAST
    *EAP Framework: Jan 18 12:08:22.833: eap_core.c:1422:     Payload:  810000000715030100020228
    *EAP Framework: Jan 18 12:08:22.833: EAP-AUTH-EVENT: EAP method state: Continue
    *EAP Framework: Jan 18 12:08:22.834: EAP-AUTH-EVENT: EAP method decision: Fail
    *EAP Framework: Jan 18 12:08:22.834: EAP-AUTH-EVENT: Current method = 43
    *EAP Framework: Jan 18 12:08:22.834: EAP-AUTH-EVENT: Sending packet to lower layer for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.834: EAP-AUTH-TX-PAK:
    *EAP Framework: Jan 18 12:08:22.834: eap_core.c:1484: Code:REQUEST  ID:0x 7  Length:0x0011  Type:FAST
    *EAP Framework: Jan 18 12:08:22.834: eap_core.c:1422:     Payload:  810000000715030100020228
    *EAP Framework: Jan 18 12:08:22.834: EAP-EVENT: Started 'Authenticator Retransmit' timer (60) for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.834: EAP-EVENT: Started EAP tick timer
    *EAP Framework: Jan 18 12:08:22.834: EAP-EVENT: Sending lower layer event 'EAP_TX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.834: LOCAL_AUTH: Found matching context for id - 319
    *EAP Framework: Jan 18 12:08:22.834: LOCAL_AUTH: (EAP:319) transmit event
    *EAP Framework: Jan 18 12:08:22.834: AuthorizationResponse: 0x13c713fc
    *EAP Framework: Jan 18 12:08:22.834: structureSize................................65*EAP Framework: Jan 18 12:08:22.834: resultCode...................................255*EAP Framework: Jan 18 12:08:22.835: protocolUsed.................................0x00000080*EAP Framework: Jan 18 12:08:22.835: proxyState...................................18:3D:A2:0A:EC:BC-02:05*EAP Framework: Jan 18 12:08:22.835: Packet contains 1 AVPs (not shown)*EAP Framework: Jan 18 12:08:22.835: LOCAL_AUTH: AAA LOCAL AUTH EAP PKT AVP attribute 4f length 11
    *EAP Framework: Jan 18 12:08:22.835: LOCAL_AUTH: AAA LOCAL AUTH TX PKT DUMP code cc id 00 type 2b
    *aaaQueueReader: Jan 18 12:08:22.838: LOCAL_AUTH: EAP: Received an auth request
    *aaaQueueReader: Jan 18 12:08:22.838: LOCAL_AUTH: Found context matching MAC address - 319
    *aaaQueueReader: Jan 18 12:08:22.838: LOCAL_AUTH: (EAP:319) Sending the Rxd EAP packet (id 7) to EAP subsys
    *EAP Framework: Jan 18 12:08:22.838: EAP-EVENT: Received event 'EAP_RX_PACKET' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.839: EAP-AUTH-RX-PAK:
    *EAP Framework: Jan 18 12:08:22.839: eap_core.c:1484: Code:RESPONSE  ID:0x 7  Length:0x0006  Type:FAST
    *EAP Framework: Jan 18 12:08:22.839: eap_core.c:1422:     Payload:  01
    *EAP Framework: Jan 18 12:08:22.839: EAP-EVENT: Stopping 'Authenticator Retransmit' timer for EAP session handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.839: EAP-AUTH-EVENT: EAP Response received by context 0x78000041
    *EAP Framework: Jan 18 12:08:22.839: EAP-AUTH-EVENT: EAP Response type = Method (43)
    *EAP Framework: Jan 18 12:08:22.839: EAP-AUTH-EVENT: Sending method data for context 0x78000041
    *EAP Framework: Jan 18 12:08:22.839: EAP-EVENT: Sending method directive 'Receive Packet' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.839: eap_fast.c-AUTH-EVENT: eap_fast_rx_packet(): EAP Fast NoData (0x2b)
    *EAP Framework: Jan 18 12:08:22.840: eap_fast.c-AUTH-EVENT: Process Response, type: 0x2b
    *EAP Framework: Jan 18 12:08:22.840: eap_fast_auth.c-AUTH-EVENT: Process Response (EAP handle = 0x78000041)
    *EAP Framework: Jan 18 12:08:22.840: eap_fast_auth.c-RX-AUTH-PAK:
    *EAP Framework: Jan 18 12:08:22.840: eap_core.c:1484: Code:RESPONSE  ID:0x 7  Length:0x0006  Type:FAST
    *EAP Framework: Jan 18 12:08:22.840: eap_core.c:1422:     Payload:  01
    *EAP Framework: Jan 18 12:08:22.840: eap_fast_auth.c-AUTH-EVENT: Received ACK from peer
    *EAP Framework: Jan 18 12:08:22.840: EAP-AUTH-EVENT: EAP method state: Done
    *EAP Framework: Jan 18 12:08:22.840: EAP-AUTH-EVENT: EAP method decision: Fail
    *EAP Framework: Jan 18 12:08:22.840: EAP-EVENT: Received get canned status from lower layer (0x78000041)
    *EAP Framework: Jan 18 12:08:22.840: EAP-EVENT: Sending method directive 'Free Context' on handle 0x78000041
    *EAP Framework: Jan 18 12:08:22.840: eap_fast.c-EVENT: Free context (EAP handle = 0x78000041)
    *EAP Framework: Jan 18 12:08:22.840: id_manager.c-AUTH-SM: Entry deleted fine id f700000e - id_delete
    *EAP Framework: Jan 18 12:08:22.840: IOS_PKI_SHIM: Session 0x335ee108 deleted
    *EAP Framework: Jan 18 12:08:2

    Now we found the reason.
    The WLC doesn´t work with the Sub CA respectively with chain certificates for device authentication.
    "Support for Chained Certificate
    In controller versions earlier than 5.1.151.0, web authentication  certificates can be only device certificates and should not contain the  CA roots chained to the device certificate (no chained certificates).
    With controller version 5.1.151.0 and later, the controller allows  for the device certificate to be downloaded as a chained certificate for  web authentication.
    Certificate Levels
    Level 0—Use of only a server certificate on WLC.
    Level 1—Use of server certificate on WLC and a CA root certificate.
    Level 2—Use of server certificate on WLC, one single CA intermediate certificate, and a CA root certificate.
    Level 3—Use of server certificate on WLC, two CA intermediate certificates, and a CA root certificate.
    WLC does not support chained certificates more than 10KB size on the WLC.
    Note: Chained certificates are supported for web authentication only; they are not supported for the management certificate."
    So the WLC can´t decode the peer certificate.

  • I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .

    HI All,
    I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
    Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
    The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
    here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
    show run-config
    Press Enter to continue...
    System Inventory
    NAME: "Chassis"   , DESCR: "Cisco 5500 Series Wireless LAN Controller"
    PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
    Burned-in MAC Address............................ 30:E4:DB:1B:99:80
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 12
    Press Enter to continue or <ctrl-z> to abort
    System Information
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.0.235.0
    Bootloader Version............................... 1.0.1
    Field Recovery Image Version..................... 6.0.182.0
    Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
    Build Type....................................... DATA + WPS
    System Name...................................... WLAN Controller 5508
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
    IP Address....................................... 10.125.18.15
    Last Reset....................................... Software reset
    System Up Time................................... 41 days 5 hrs 14 mins 42 secs
    System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
    Current Boot License Level....................... base
    Current Boot License Type........................ Permanent
    Next Boot License Level.......................... base
    Next Boot License Type........................... Permanent
    Configured Country............................... US - United States
    --More or (q)uit current module or <ctrl-z> to abort
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +36 C
    External Temperature............................. +20 C
    Fan Status....................................... OK
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 10
    Number of Active Clients......................... 61
    Burned-in MAC Address............................ 30:E4:DB:1B:99:80
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 12
    Press Enter to continue or <ctrl-z> to abort
    AP Bundle Information
    Primary AP Image  Size
    ap3g1             5804
    ap801             5192
    ap802             5232
    c1100             3096
    c1130             4972
    c1140             4992
    c1200             3364
    c1240             4812
    c1250             5512
    c1310             3136
    c1520             6412
    c3201             4324
    c602i             3716
    Secondary AP Image      Size
    ap801             4964
    c1100             3036
    --More or (q)uit current module or <ctrl-z> to abort
    c1130             4884
    c1140             4492
    c1200             3316
    c1240             4712
    c1250             5064
    c1310             3084
    c1520             5244
    c3201             4264
    Press Enter to continue or <ctrl-z> to abort
    Switch Configuration
    802.3x Flow Control Mode......................... Disable
    FIPS prerequisite features....................... Disabled
    secret obfuscation............................... Enabled
    Strong Password Check Features:
           case-check ...........Enabled
           consecutive-check ....Enabled
           default-check .......Enabled
           username-check ......Enabled
    Press Enter to continue or <ctrl-z> to abort
    Network Information
    RF-Network Name............................. OGR
    Web Mode.................................... Disable
    Secure Web Mode............................. Enable
    Secure Web Mode Cipher-Option High.......... Disable
    Secure Web Mode Cipher-Option SSLv2......... Enable
    OCSP........................................ Disabled
    OCSP responder URL..........................
    Secure Shell (ssh).......................... Enable
    Telnet...................................... Disable
    Ethernet Multicast Forwarding............... Disable
    Ethernet Broadcast Forwarding............... Disable
    AP Multicast/Broadcast Mode................. Unicast
    IGMP snooping............................... Disabled
    IGMP timeout................................ 60 seconds
    IGMP Query Interval......................... 20 seconds
    User Idle Timeout........................... 300 seconds
    ARP Idle Timeout............................ 300 seconds
    Cisco AP Default Master..................... Enabled
    AP Join Priority............................ Disable
    Mgmt Via Wireless Interface................. Disable
    Mgmt Via Dynamic Interface.................. Disable
    --More or (q)uit current module or <ctrl-z> to abort
    Bridge MAC filter Config.................... Enable
    Bridge Security Mode........................ EAP
    Mesh Full Sector DFS........................ Enable
    AP Fallback ................................ Enable
    Web Auth Redirect Ports .................... 80
    Web Auth Proxy Redirect ................... Disable
    Fast SSID Change ........................... Enabled
    AP Discovery - NAT IP Only ................. Enabled
    IP/MAC Addr Binding Check .................. Enabled
    Press Enter to continue or <ctrl-z> to abort
    Port Summary
               STP   Admin   Physical   Physical   Link   Link
    Pr Type   Stat   Mode     Mode     Status   Status Trap    POE   SFPType  
    1 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
    2 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    3 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    4 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    5 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    6 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    7 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    8 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    Press Enter to continue or <ctrl-z> to abort
    AP Summary
    Number of APs.................................... 8
    Global AP User Name.............................. Not Configured
    Global AP Dot1x User Name........................ Not Configured
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KNOWLOGY_DC01       2     AIR-LAP1131AG-A-K9   00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1       US       1
    KNOWLOGY_DC02       2     AIR-LAP1131AG-A-K9   00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1       US       1
    KN1252_AP01         2     AIR-LAP1252AG-A-K9   00:21:d8:ef:06:50 Knowlogy Confere 1       US       1
    KN1252_AP02         2     AIR-LAP1252AG-A-K9   00:22:55:8e:2e:d4 Server Room Side 1       US       1
    Anham_AP03           2     AIR-LAP1142N-A-K9     70:81:05:88:15:b5 default location 1       US       1
    ANHAM_AP01          2     AIR-LAP1142N-A-K9     70:81:05:b0:e4:62 Small Conference 1       US       1
    ANHAM_AP04           2     AIR-LAP1131AG-A-K9   00:1d:45:86:e1:b8   Conference room 1       US       1
    ANHAM_AP02           2     AIR-LAP1142N-A-K9     70:81:05:96:7a:49         Copy Room 1       US       1
    AP Tcp-Mss-Adjust Info
    AP Name             TCP State MSS Size
    KNOWLOGY_DC01       disabled   -
    KNOWLOGY_DC02       disabled   -
    --More or (q)uit current module or <ctrl-z> to abort
    KN1252_AP01         disabled   -
    KN1252_AP02         disabled   -
    Anham_AP03           disabled   -
    ANHAM_AP01           disabled   -
    ANHAM_AP04           disabled   -
    ANHAM_AP02           disabled   -
    Press Enter to continue or <ctrl-z> to abort
    AP Location
    Total Number of AP Groups........................ 3  
    Site Name........................................ ANHAM8075
    Site Description................................. ANHAM 8075 Location
    WLAN ID         Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    9               knowlogy_ogr         Disabled                         None
    7               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    Anham_AP03           2     AIR-LAP1142N-A-K9   70:81:05:88:15:b5 default location 1     US       1
    ANHAM_AP01           2     AIR-LAP1142N-A-K9   70:81:05:b0:e4:62 Small Conference 1     US       1
    ANHAM_AP04           2     AIR-LAP1131AG-A-K9   00:1d:45:86:e1:b8   Conference room 1     US       1
    ANHAM_AP02           2     AIR-LAP1142N-A-K9   70:81:05:96:7a:49         Copy Room 1     US       1
    Site Name........................................ Knowlogy_DC
    --More or (q)uit current module or <ctrl-z> to abort
    Site Description................................. DC Center Access points
    WLAN ID         Interface         Network Admission Control         Radio Policy
    2               knowlogy_ogr         Disabled                         None
    4               knowlogy_ogr         Disabled                         None
    3               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KNOWLOGY_DC01       2     AIR-LAP1131AG-A-K9   00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1     US       1
    KNOWLOGY_DC02       2     AIR-LAP1131AG-A-K9   00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1     US       1
    Site Name........................................ OGR
    Site Description................................. 1934 OGR Office
    WLAN ID         Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    2               knowlogy_ogr         Disabled                        None
    4               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    --More or (q)uit current module or <ctrl-z> to abort
    7               knowlogy_ogr        Disabled                         None
    9               knowlogy_ogr         Disabled                         None
    8               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KN1252_AP01         2     AIR-LAP1252AG-A-K9   00:21:d8:ef:06:50 Knowlogy Confere 1    US       1
    KN1252_AP02         2     AIR-LAP1252AG-A-K9   00:22:55:8e:2e:d4 Server Room Side 1     US       1
    Site Name........................................ default-group
    Site Description................................. <none>
    WLAN ID        Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    2               knowlogy_ogr         Disabled                         None
    3               knowlogy_ogr         Disabled                         None
    4               knowlogy_ogr         Disabled                         None
    5               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    7               knowlogy_ogr         Disabled                         None
    8               knowlogy_ogr         Disabled                          None
    --More or (q)uit current module or <ctrl-z> to abort
    9               knowlogy_ogr         Disabled                         None
    10             management           Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    Press Enter to continue or <ctrl-z> to abort
    AP Config
    Cisco AP Identifier.............................. 6
    Cisco AP Name.................................... KNOWLOGY_DC01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:1d:45:86:ed:4e
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.100
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................ wireless.knowlogy.com
    Primary Cisco Switch IP Address.................. 10.125.18.15
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    --More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    --More or (q)uit current module or <ctrl-z> to abort
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1134T0QG
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 48 days, 20 h 19 m 18 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:33 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 47 s
    --More or (q)uit current module or <ctrl-z> to abort
    Attributes for Slot 0
        Radio Type................................... RADIO_TYPE_80211b
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:1d:71:09:8f:90
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
           11000 Kilo Bits.......................... MANDATORY
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
    --More or (q)uit current module or <ctrl-z> to abort
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
        Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 .......................... 11 dBm
         Tx Power Level 5 .......................... 8 dBm
         Tx Power Level 6 .......................... 5 dBm
         Tx Power Level 7 .......................... 2 dBm
         Tx Power Level 8 .......................... -1 dBm
    --More or (q)uit current module or <ctrl-z> to abort
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy DSSS parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 11
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
         Current CCA Mode .......................... 0
         ED Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 12 dB
    --More or (q)uit current module or <ctrl-z> to abort
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Cisco AP Identifier.............................. 6
    Cisco AP Name.................................... KNOWLOGY_DC01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:1d:45:86:ed:4e
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.100
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................ wireless.knowlogy.com
    Primary Cisco Switch Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1134T0QG
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    --More or (q)uit current module or <ctrl-z> to abort
    AP Up Time....................................... 48 days, 20 h 19 m 18 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:33 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 47 s
    Attributes for Slot 1
       Radio Type................................... RADIO_TYPE_80211a
       Radio Subband................................ RADIO_SUBBAND_ALL
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
          CFP MaxDuration ........................... 60
         BSSID ..................................... 00:1d:71:09:8f:90
         Operation Rate Set
           6000 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           9000 Kilo Bits........................... SUPPORTED
           12000 Kilo Bits.......................... MANDATORY
           18000 Kilo Bits.......................... SUPPORTED
           24000 Kilo Bits.......................... MANDATORY
          36000 Kilo Bits.......................... SUPPORTED
           48000 Kilo Bits.......................... SUPPORTED
           54000 Kilo Bits.......................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 36
         Number Of Channels ........................ 20
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
    --More or (q)uit current module or <ctrl-z> to abort
       Tx Power
         Num Of Supported Power Levels ............. 7
         Tx Power Level 1 .......................... 15 dBm
         Tx Power Level 2 .......................... 14 dBm
         Tx Power Level 3 .......................... 11 dBm
         Tx Power Level 4 .......................... 8 dBm
         Tx Power Level 5 .......................... 5 dBm
         Tx Power Level 6 .......................... 2 dBm
         Tx Power Level 7 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy OFDM parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 44
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
           ......................................... 104,108,112,116,132,136,140,
           ......................................... 149,153,157,161
         TI Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
    --More or (q)uit current module or <ctrl-z> to abort
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
          Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 16 dB
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Press Enter to continue or <ctrl-z> to abort
    Cisco AP Identifier.............................. 3
    Cisco AP Name.................................... KNOWLOGY_DC02
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:36:c5:c4
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.101
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    --More or (q)uit current module or <ctrl-z> to abort
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W  Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Enabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    --More or (q)uit current module or <ctrl-z> to abort
    AP Serial Number................................. FTX1230T24F
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 48 days, 20 h 24 m 41 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:35 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 48 s
    --More or (q)uit current module or <ctrl-z> to abort
    Attributes for Slot 0
       Radio Type................................... RADIO_TYPE_80211b
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
        Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:a5:0c:30
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
           11000 Kilo Bits.......................... MANDATORY
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
    --More or (q)uit current module or <ctrl-z> to abort
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 .......................... 11 dBm
         Tx Power Level 5 .......................... 8 dBm
         Tx Power Level 6 .......................... 5 dBm
         Tx Power Level 7 .......................... 2 dBm
         Tx Power Level 8 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
    --More or (q)uit current module or <ctrl-z> to abort
         Current Tx Power Level .................... 1
       Phy DSSS parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 1
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
         Current CCA Mode .......................... 0
         ED Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 12 dB
         Coverage exception level................... 25 %
    --More or (q)uit current module or <ctrl-z> to abort
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Cisco AP Identifier.............................. 3
    Cisco AP Name.................................... KNOWLOGY_DC02
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:36:c5:c4
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.101
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    --More or (q)uit current module or <ctrl-z> to abort
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Enabled
    PoE Power Injector MAC Addr...................... Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1230T24F
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    --More or (q)uit current module or <ctrl-z> to abort
    AP Up Time....................................... 48 days, 20 h 24 m 41 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:35 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 48 s
    Attributes for Slot 1
       Radio Type................................... RADIO_TYPE_80211a
       Radio Subband................................ RADIO_SUBBAND_ALL
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:a5:0c:30
         Operation Rate Set
           6000 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           9000 Kilo Bits........................... SUPPORTED
           12000 Kilo Bits.......................... MANDATORY
           18000 Kilo Bits.......................... SUPPORTED
           24000 Kilo Bits.......................... MANDATORY
           36000 Kilo Bits.......................... SUPPORTED
           48000 Kilo Bits.......................... SUPPORTED
           54000 Kilo Bits.......................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 36
         Number Of Channels ........................ 20
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
    --More or (q)uit current module or <ctrl-z> to abort
       Tx Power
         Num Of Supported Power Levels ............. 7
         Tx Power Level 1 .......................... 15 dBm
        Tx Power Level 2 .......................... 14 dBm
         Tx Power Level 3 .......................... 11 dBm
         Tx Power Level 4 .......................... 8 dBm
         Tx Power Level 5 .......................... 5 dBm
         Tx Power Level 6 .......................... 2 dBm
         Tx Power Level 7 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy OFDM parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 36
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
           ......................................... 104,108,112,116,132,136,140,
           ......................................... 149,153,157,161
         TI Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
    --More or (q)uit current module or <ctrl-z> to abort
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
          Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 16 dB
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Press Enter to continue or <ctrl-z> to abort
    Cisco AP Identifier.............................. 5
    Cisco AP Name.................................... KN1252_AP01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:ef:06:50
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.125.18.101
    IP NetMask....................................... 255.255.255.0
    Gateway IP Addr.................................. 10.125.18.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Enabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ Knowlogy Conference Rooms Side
    Cisco AP Group Name.............................. OGR
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    --More or (q)uit current module or <ctrl-z> to abort
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.4.10.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. PoE/Medium Power (15.4 W)
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1252AG-A-K9
    AP Image......................................... C1250-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    --More or (q)uit current module or <ctrl-z> to abort
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX122990L5
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 118
          WLAN 1 :........................................ 111
          WLAN 2 :........................................ 111
          WLAN 4 :........................................ 112
          WLAN 6 :........................................ 112
          WLAN 7 :........................................ 111
          WLAN 9 :........................................ 112
          WLAN 8 :........................................ 112
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 26 days, 00 h 24 m 39 s
    --More or (q)uit current module or <ctrl-z> to abort
    AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
    Join Date and Time............................... Wed Oct 9 10:59:07 2013
    Join Taken Time.................................. 0 days, 00 h 00 m 50 s
    Attributes for Slot 0
       Radio Type................................... RADIO_TYPE_80211n-2.4
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 7
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:df:a5:90
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           11000 Kilo Bits.......................... MANDATORY
         MCS Set
           MCS 0.................................... SUPPORTED
           MCS 1.................................... SUPPORTED
           MCS 2.................................... SUPPORTED
           MCS 3.................................... SUPPORTED
           MCS 4.................................... SUPPORTED
           MCS 5.................................... SUPPORTED
           MCS 6.................................... SUPPORTED
           MCS 7.................................... SUPPORTED
           MCS 8.................................... SUPPORTED
            MCS 9.................................... SUPPORTED
           MCS 10................................... SUPPORTED
           MCS 11................................... SUPPORTED
           MCS 12................................... SUPPORTED
           MCS 13................................... SUPPORTED
           MCS 14................................... SUPPORTED
           MCS 15................................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
    --More or (q)uit current module or <ctrl-z> to abort
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 ..........

    Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
    Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
    There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
    Sent from Cisco Technical Support iPhone App

  • Web Redirection Problem on Cisco ISE 1.2 and WLC 7.5

    Hello,
    We are at initial phase of deploying ISE 1.2 in our environment for Wireless Guest Users.
    I have configured ISE and WLC to talk to each other which is working fine. An SSID with MAC-Filtering is also configured on WLC and ACL only allowing ISE and DNS traffice.
    I have configured proper authentication and authorization policies on ISE. Now, when I try to connect my device (laptop and android mobile), I see my device gets associated with the SSID (Demo) and gets the right IP Address from DHCP and right VLAN from WLC. The log process on ISE is as follows.
    11001
    Received RADIUS Access-Request
    11017
    RADIUS created a new session
    11027
    Detected Host Lookup UseCase (Service-Type = Call Check (10))
    15049
    Evaluating Policy Group
    15008
    Evaluating Service Selection Policy
    15048
    Queried PIP
    15048
    Queried PIP
    15004
    Matched rule
    15041
    Evaluating Identity Policy
    15006
    Matched Default Rule
    15013
    Selected Identity Source - Internal Endpoints
    24210
    Looking up User in Internal Users IDStore - B8:B4:2E:A6:7D:75
    24216
    The user is not found in the internal users identity store
    24209
    Looking up Endpoint in Internal Endpoints IDStore - B8:B4:2E:A6:7D:75
    24211
    Found Endpoint in Internal Endpoints IDStore
    22037
    Authentication Passed
    15036
    Evaluating Authorization Policy
    15048
    Queried PIP
    15048
    Queried PIP
    15048
    Queried PIP
    15004
    Matched rule - Guest Redirection
    15016
    Selected Authorization Profile - Test_Profile
    11002
    Returned RADIUS Access-Accept
    I also see a redirect url in the detailed authentication logs. But the problem is that when I open my browser on my device, it doesn't get redirected to the guest portal url. Now since I can't get there, I can't continue with the rest of the process of authentication, COA and final ACL for internet access.
    Can some one please either guide me the correct steps that I need to follow, if I have mis configured something or advise if this is a bug.
    Thanks in advance.
    Jay

    The ACL is definitely used to define what traffic is re-directed to ISE and what traffic is not redirected. Having the permit-all statement at the end will break redirection. If you are using flex-connect then you will need to use flex-connect ACLs and apply those to the flex-connect APs. The links below should give you an idea of what needs to be done:
    http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/113606-byod-flexconnect-dg-000.html
    http://www.cisco.com/c/en/us/support/docs/security/identity-services-engine/116087-configure-cwa-wlc-ise-00.html
    Thank you for rating helpful posts! 

Maybe you are looking for

  • Only getting static, no channels, etc

    Hi, i have recently purchased an MSI VOX  usb2 device, and have installed it without any obvious problems (it is displayed in control panel, the programs- both windvd and the intervideo program, can recognise it) and yet cannot get a picture from any

  • Statement "++" is not defined.?

    Hi i write the code as below. FORMAT COLOR COL_BACKGROUND INTENSIFIED.     ++ '001'.     WRITE: /    TXT           COLOR COL_BACKGROUND INTENSIFIED,              23 XFAKKTS-KUNNR COLOR COL_BACKGROUND INTENSIFIED OFF. I am getting error " Statement "+

  • ITunes repeatedly crashes.

    I did a clean uninstall & downloaded and reinstalled itunes only to have the same error flash up. It's getting really annoying and I'd appreciate any help! The crash report is attached. Process:         iTunes [491] Path:            /Applications/iTu

  • VIP in Intermediate state after relocate

    11.2.0.2.0 windows 2008 2 node RAC Rolling patch. Brought down and relocated all services to node 2. All services start ok except for node 1 VIP which goes to intermediate and FAILED OVER state. C:\Windows\system32>crsctl status resource -t ora.rac01

  • Frequent Freezing (Captivate 7)

    Hello, I am testing Captivate 7 after a few months now of familiarizing myself with Captivate 6.When editting my recorded Video Demo I have noticed very frequent freezing of the program. Is there an auto save feature when using Video Demo mode or som