Workgroup Bridge and local Wifi Config

Question

Hi all, hoping you can help me with this, just need an other brain as mine is empty as I've been staring at this for too long!!!
What I'm trying to config is to have a standalone local WLAN (Built into a VAN) running on the 2.4ghz and then also have a workgroup bridge on the 5ghz to the corporate lan.
Setup is this:
2960<-->1142(autonomous)   <--Workgroup bridge on 5Ghz-->  1131(Lightweight)<3560>--<5508WLC> (hope that makes sense!!)
So  far I have the bridge working, the 1142 connects to a ssid on the 1131  using psk. I can see the 1142 as an assosiated client on the wlc and I  can ping the the lan from the 1142 so I'm happy the bridge is working.
Clients  connected to the 2.4ghz ssid on the 1142 can only ping through as far  as the AP(1142) I can't seem to get the traffic to pass across the  bridge, is there something I need to do to link the 2.4 to the 5ghz  bridge link?
Any help always appreciated, cheers.

Answer 1

dmantill - Thanks for your link. I have read through and checked my config but my plan is to have a number of clients, all dhcp assigned, connecting to the do0 int for local wlan breakout.
I'm not sure that the passive config will help me there.
Steven - I have enabled the wgb on the do1 int and I am connecting clients on the do0 int for local wlan breakout. Enabling the WGB has not disabled the other radio on my setup.
I was running 7.0.98.0 but have today upgraded to 7.0.98.218 on my WLC but that has not helped.
From what I can tell it looks like my problem just lies with routing traffic across the 2 radios. My local clients can ping as far as the WGB and if I CLI into the WGB AP I can ping the corporate lan on the otherside of the bridge and can also ping from the lan to the WGB. I just cannot seem to get the 2 ssid's to route between each other.
Here's my WGB config, hope this brings some more ideas!!
Cheers,
Jason.
Current configuration : 1555 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname XXX
logging rate-limit console 9
enable secret 5 $1$ujWI$HMYMAjMfJV2J2WaGa1/JJ0
no aaa new-model
dot11 syslog
dot11 ssid XXX       
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 105A0C0A11001D1908
dot11 ssid XXX       
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 080F15480C090D1221
username Cisco password 7 02250D480809
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid XXX
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid XXX
antenna gain 0
station-role workgroup-bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
bridge 1 aging-time 216000
line con 0
line vty 0 4
login local
end