Normal string ASCII characters are not shown after using string reversal.

In a VI that I have written, there is a point where I take a simple 5 character string and input it to a reverse string node.  I also have an indicator on the output of the reverse string node so I can look at the reversed string.  Both the input and output indicators are in normal display mode.   For the input indicator I can see the input string with no problem.  But on the indicator at the output of the reverse string node I see nothing.  If I then put each of the indicators in HEX display mode, both indicators display the hex equivalent characters of the original ASCII characters, and the output indicator shows the characters reversed from that of the input indicator, as expected.  So why when I am in normal display mode, are the characters in the output indicator not showing up?  Thanks.

What are the ASCII values that you are trying to display?  Perhaps they are non-printable ASCII values.
Perhaps you can post a simple VI with the values in a string control and saved as a default.
EDIT:  After seeing Rod's message, that seems very likely, especially considering that there is likely an EOL character if you are doing serial communication with some other device.
Message Edited by Ravens Fan on 03-23-2009 12:04 PM

Similar Messages

  • Special characters are not shown in compare document report in Acrobat X

    Hi All,
    I have a pdf document which is having some special characters like üὄ. Now I have updated the document with few corrections and while compare document in Acrobat X special characters are not shown in the report.
    Can any one please look into this and give suggestion.

    Hi Steve,
    Thanks for your reply.
    Platform - PC
    Application - 3B2 and Acrobat 9
    So far we have seen this kind of issue in only one document. In the below screenshot you can see 2 pdf files, the right side one is my MS pdf and the left side one is the exported pdf from 3B2 application both the files having the special characters such as . I just did the text comparison however both   and  is missing in the exported pdf but the reports shown the changes for  characters only wherever the  charactes is missing the report not shown the changes properly(See highlighted in yellow).
    Please let me know if you need more deatails.

  • Images in mail are not shown after ios8 update

    After update iOS8 the images attached in mails are not shown constantly, I configured my iPhone and iPad to show the images in mails but it is not working all time.
    The issue is with photos sent from my ip cameras, these are showing for one mail and for other not.
    Thanks in advance.

    Actually yes!
    I'm not familiar with fuse, but I found the action in line one of your third frame (on the main timeline) dubious, and a quick search lead me to try "portfolio._brightness = 0;" as first line (and I commented out the original line) that worked.
    My quess is that whatever template or original file you've been modifing/adjusting used some kind of color-fade in at that point, and you somehow broke it.
    To me it looks ok without it, but you let me know if you need further guesswork from me.
    cheers
    M

  • Images are not shown after deploying in apps

    After deploying my application in apps i have put all my images in media folder even then the images are not displaying, can any tell me what is the reason for this, but when i have deployed before it was working fine...

    when the page is displayed without the image, right click on the image place holder and click on properties. Under General tab,
    address will show you the place/url page is looking for the image. Make sure you have put the image on that path and the name of image mathes the case as well.
    --Tanveer                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                           

  • SAP Webdispatcher :Images are not displayed after using the URL filtering

    Hello,
    I have installed the SAP webdispatcher 7.3 on Linux redhat 5.4 in front of the Portal 7.3.
    I wanted to restrict the access just for the IRJ prefix so for this i used the parameter wdisp/permission_table = PermFile
    with Permfile as follows:
    #Denial of the useradmin URL from the WebDispatcher
    P /irj*
    P /irj/*
    The filtering is working well except that for IRJ the images are not displayed so i was using so i added the following line to disply the images to the logon page
    icm/HTTP/auth_
    P /logon_ui_resources/*
    P /logon_ui_resources*
    but i still have the same issue for the irj page where no icons are displayed and i can do nothing.
    The same issue also happened when using the icm/HTTP/auth_xx
    Do you have an idea how to deal with this issue?
    Thanks in advance;
    Hassan

    Hello,
    After checking the HTTP code of the irj page on IE,  i foud the needed URL to permit so i modified the permision table and it works fine for the moement
    P /irj*
    P /irj/*
    P /logon_ui_resources/*
    P /logon_ui_resources*
    P /AFPServlet/*
    P /AFPServlet*
    P /com.sap*
    P /com.sap/*
    P /webdynpro/resources*
    P /webdynpro/resources/*
    Thanks for you help,
    Hassan

  • Symbol characters are not shown correctly in webbrowser

    Hello,
    I have migrated my Forms 6i-application to Forms 11G R2 (11.1.2.0).
    Most problems I have solved. But now I see that Symbol-Characters in boilerplate-text in Formsbuilder are shown correct, but in the web they appear as "translated". In my case the Omega is turned to W.
    In the registry.dat I placed Symbol to be carried to Symbol because I read java could use Symbol.
    But I am wrong.
    Do you know what I must do to get the boilerplatetext shown in the rigth way?
    Thanks in advance.
    best regards
    Eveline Merches

    See my comments in this post:
    client_get_file_name do not go to specified folder

  • Selection-screen texts are not shown after transporting to QAS server...

    Hello Experts,
    We created a custom transaction for MB52(Display warehouse stocks) named ZMB52.
    After I transported it to QAS server, the texts in the selection screen are shown
    as for example, p_bukrs, etc. When I looked at its text elements, it is maintained
    in German Language. My question is, should I translate it to English? And How do I
    properly transport it.
    Hope you can help me out here guys.Thank you and take care!

    Hi
    Have you created your own Selection screen Text elements
    or you simply copied the Std ones
    If you have created on your own it should have asked for the request and should have been transported with the request
    since you copied them as it is it is not displaying in ENglish language
    Translate to english and see
    otherwise create them in DEV with a request and transport it.
    Reward points for useful Answers
    Regards
    Anji

  • Pages are not loading after using for 20 min so i have to use task maneger to shut it down and restart

    i can download for about 20 min then i try to go to another page by opening a new tab or using a bookmark Firefox totally freeze's up so i have to close down and go into the task mngr and shut down the process for firefox and restart because if i do not do that it will not open back up i am using vista home pro on a 64 bit system please help this very bothersome

    This issue can be caused by an extension or plugin that isn't working properly.
    Start Firefox in [[Safe Mode]] to check if one of the add-ons is causing the problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
    * Don't make any changes on the Safe mode start window.
    See:
    * [[Troubleshooting extensions and themes]]
    * [[Troubleshooting plugins]]

  • Why Arabic charactes in PDF are not shown ?

    I have Microsoft IIS , oracle report server , Acrobat writer 5 and report builder 6
    in Windows2000 with Arabic language enabled.
    In live previewer and HTML format Arabic characters are shown correctly in my report
    also when i print my report by Acrobat distiller printer, but when i generate to file PDF ,
    arabic characters are not shown correctly (they are not shown as question marks )
    this meanes that my reports in IE5 as PDF do not show arabic characters.
    How Can I define my Acrobat distiller printer as default printer used by web CGI (rwcgi60) ?
    I have found this statment in developer documents:
         "PDF does not support multi-byte character sets."
    wether it meanes that i can not have reports with arabic characters as PDF?
    thanks for your help.

    Jalal,
    BiDi was not supported in PDF output in reports 6/6i. It is supported in reports 9i.
    Thanks
    The Oracle Reports team

  • Why is some text not shown after merging multiple documents

    One of my clients is using Adobe Acrobat XI and they are merging multiple PDF documents (up to 1000 single PDF's!) to create one big PDF document.
    But somehow just some parts of the text are not shown after the merging (it is actually still there because you can copy and paste it in to Word and you will see it again)?
    Any suggestions?

    Hi Wunold van Drunen,
    Since you have identified the problematic pages, have you checked if the issue occurs with the same pdf when merged with a smaller number may be 10 pdfs.
    How are these pdfs created? It might be possible that the said document's pdf structure is incorrect.
    You may want to sanitize the said pdf's before combining and check.
    Regards,
    Rave

  • I'm on a windows laptop using iTunes sharing through the family to connect with Apple TV. After choosing the folder of photos to be shared and displayed on the appletv and when I choose to show on screen, they are not shown in the order they are in the or

    I'm on a windows laptop using iTunes sharing through the family to connect with Apple TV.
    After choosing the folder of photos to be shared and displayed on the appletv and when I choose to show on screen, they are not shown in the order they are in the original folder.
    How to pair show in a certain order, for example, sorted by name.
    grateful
    Julio Cesar

    Not that I'm aware of. You just export JPEG copies to a folder that you can point iTunes to. For instance, I have created a folder in my Pictures folder called Apple TV. And within that folder I have other folders of pictures that I can choose from in iTunes to share with Apple TV. But there doesn't seem to be any way to share a Lightroom slideshow. If you have laid to create a video file that would probably work. Apple TV is a little clunky in my opinion. Some things are a little more difficult to do now than they were a while back. I probably haven't provided you with much help, but just keep experimenting and I think you will figure it out.

  • Contact bug : contact phone numbers in edit mode are not shown in "dial" mode

    Contacts can have seemingly unlimited phone numbers as seen in the contact edit mode, though very few are shown in the corresponding non-edit mode. Of course, Dialing is not supported in the edit mode.
    I have found that contacts that include pause characters or block characters are not properly displayed in the contact "dial mode".  If you every try a conference call service, this is important to you.
    At&t uses the comma as a pause, and Verizon uses the letter "t" as a pause.  *82 temporarily blocks your caller id.  Somehow the WebOS software that chooses which items to allow me to dial has bugs and worse, there is no clear way to prioritize so I am completely at the whim of the software.

    I have tested entering 12 phone numbers on my own Pre Plus and all the numbers display in the normal contact field. How many phone numbers are you trying to to display?
    The dialing options on the Palm Pre Plus are as follows:
    To insert a two-second pause in the dialing sequence, enter a T where you want the pause to appear. To add a + symbol in the dialing sequence for international dialing, press and hold 0 (zero) in the location where you want the + symbol to appear. To insert a stop in the dialing sequence, enter a P where you want the stop to appear; to dial the next set of numbers after the stop, tap the screen.
    As far as 3rd party special dialing character entry you would need to check with the 3rd party on how to enter this information into you device for your conference calling service.

  • Bridge New keywords are not shown on startup

    Hi,
    I have some images, (in folder X) which I tagged with NEW keywords I created.
    When I reopen bridge, these new keywords are not shown by default.
    In ordert to see the above keyword, in the keyword panned, i have to navigate to folder X.
    Is this a normal behavoure for bridge?
    Is there a way to show all the new user ekywords on startup?
    I am working with bridgew CS6, win7 x64.

    I have some images, (in folder X) which I tagged with NEW keywords I created.
    When I reopen bridge, these new keywords are not shown by default.
    I think you use Photoshop or other application to add keywords?
    The Bridge keyword panel offers you the option to create your own keyword list with parent keywords and sub keywords in it. You can also import an existing keyword list using the little menu icon top right in the keyword panel. And export for back up or new version and/or computer.
    If you have Bridge pointed to a file the keywords do show in the list but as italic instead of normal. This means the file has a keyword that is not in the list of Bridge itself. You can make it persistent by using right mouse click on the keyword and after this it shows always in the panel regardless if you point to the file with the keyword or not.
    So if you want to make the most of your search function and using keywords you should start to build your own list. This can be done in Bridge but also in a simple text application. Just try to add some different keywords with a couple of sub keywords to the metadata panel and when done use the export function. This provides you with a good example of how to make your own list in a text application that you then cam import again.
    Off course before staring to create a long list in a text application be sure to start with a short list and see if importing succeeds…

  • Chinese characters are not displayed in the Firefox bookmarks

    Chinese characters are not displayed in the Firefox bookmarks. The name looks like e.g. "??????? ???? cn.nytimes.com"
    Chinese character of the site name is displayed ok in the head of the browser window and there is no problem reading chinese web content. I use Firefox Portable 11 /English from portableapps.com in Windows XP.
    I googled and got some tips:
    1) Set your browser to recognise Chinese language internet sites.
    Windows users: Under "Tools - Options" on your browser's menu-bar add Chinese to the languages list.
    - I did this.
    2) Set your browser's "Character Set" or "Encoding" to UTF-8 (sometimes also called Universal Alphabet or Unicode).
    Encoding settings can be changed under the "View" option in your browser's menu-bar.
    - It was already set to UTF-8.
    3) Windows users: If Chinese text still does not display correctly, East Asian language support may need to be enabled.
    - This has been done when I installed Windows.
    I still don't get any Chinese fonts in the bookmark names. I can edit the bookmark name with chinese characters and then save the bookmark, it works fine. But why does not Firefox recognize the characters when saving bookmarks? Help is appreciated.

    No I didn't change anything deep beneath the hood. My problem didn't apply to the URL, but to the name of the link or bookmark header or whatever you would like to call it. (When hitting Ctrl + D there is a Name field). I only got ???????? instead of chinese characters in the name. Also for e.g. www.cntv.cn ...but maybe all China is not in the whitelist either. ;-) But anyway, this was not the real problem for me.
    Apparently I was wrong as after a reboot of the computer it worked. The solution seemed to be to add Chinese to the language list. I don't know why it was not enough to restart Firefox?
    Now I only have problems to show chinese characters in the name field of my external link manager... But I guess it is not an issue for Mozilla.

  • Polish characters are not retrived from request object

    Hi
    I have a problem in passing POLISH character through request object.
    I am calling a servlet from a jsp with a hyper link. when the link in jsp is clicked the following code will be executed
    response.sendRedirect(response.encodeURL("http://hostname:8080/appName/abc.do?method=getReport&FirstName=Ko�tun&LastName=Pro�ciak"));
    this code is passing two POLISH strings First Name & Last Name to the servlet.
    In the servlet i am trying to retrieve the values of the parameters "FirstName" & "LastName".
    Sring FN=request.getParameter("FirstName");
    String LN=request.getParameter("LastName");
    The variable FN & LN doesn't show the POLISH character in servlet.
    I tried with the below option in JSP
    <meta content="text/html; charset=ISO-8859-2" > (or)
    <meta content="text/html; charset=UTF-8" >
    (or)
    <%@ page contentType="text/html;charset=ISO8859_2" %>
    (or)
    <%@ page contentType="text/html;charset=UTF-8" %>
    In Servlet i tried using
    request.setCharacterEncoding("ISO-8859-2");
    (or)
    request.setCharacterEncoding("UTF-8");
    Pl help me.
    Thanks in advance

    Don't do it then. Those characters are not allowed inside a URL and have to be encoded. You know, that %... stuff.

Maybe you are looking for